Simmons DA2012B Manuel utilisateur

Simmons
Marque
Simmons
Modèle
DA2012B
Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur
SimmonsDrums.net
OWNER’S MANUAL
2
SETTING UP / HELPFUL TIPS
• Position the DA2012B in the desired location, and ensure the amp
is stable.
• Make sure the Power Switch is off.
• Turn Channel 1, 2, and 3 knobs to minimum.
• Turn Bass and Treble to center/straight up.
MAKING THE CONNECTIONS
• Connect sources to Channel 1, 2 and 3 input jacks as desired.
(All these input jacks can be used at once, along with Bluetooth
audio input.)
CHECK SWITCHES
• Check that Mono / Stereo Master / Link In switch
is set to Mono.
POWERING UP
• Power on any devices connected to input jacks.
• Turn up the output volume of all sources.
• Turn Channel 1, 2 and 3 knobs to desired levels.
FOR FLOOR MONITOR USE
• Press rear panel VOICINGS button to light one of the FLOOR LEDs.
FOR USE ON POLE OR FREE STANDING VERTICALLY
• Press rear panel VOICINGS button to light one of the POLE LEDs.
BLUETOOTH AUDIO INPUT
• From your Bluetooth audio source device, look for DA2012B and
select it.
• See next page for Bluetooth Troubleshooting in case of difficulty.
FRONT LED LIGHT
• Check that rear panel button for FRONT LED is pressed in (On/Limit
position)
• When front LED lights red, limiter is being triggered, and Channel 1,
2, and 3 knobs may need to be turned down
DA2012B can be used as an upward-angled floor monitor, on a pole,
or standing vertically on the floor or other stable surface.
QUICK START GUIDE
Speaker stand not included
Main
Floor Monitor
DA2012B ADVANCED DRUM AMPLIFIER
3
SMART STEREO WITH DA2012B
A pair of DA2012B drum amplifiers can operate together as a Smart
Stereo system, giving you control of the sound and volume of both
amplifiers from the first master amplifier, and optimally distributing
all audio inputs to both amplifiers for rich stereo sound.
1
Connect all inputs and make all sound settings on the first (left)
unit only. The second (right) unit’s inputs and controls are all
disabled when it is set to Link In.
2
Set the switch on first unit to Stereo Master.
3
Set the switch on second unit to Link In.
4
Connect an XLR (microphone) cable from the first unit’s OUT jack
to the second unit’s LINK IN.
1
2 3
4
BLUETOOTH
®
TROUBLESHOOTING
These steps should resolve any Bluetooth trouble you may encounter:
• Power off the DA2012B and leave it off
• On your Apple iOS device
1. Open Settings app, select Bluetooth
2. If DA2012B is listed under MY DEVICES, touch info button,
tap to Forget This Device
3. Turn off Bluetooth, wait 10 seconds, turn on Bluetooth
• On your Android device
1. Open Settings, select Bluetooth
2. If DA2012B is listed under Paired Devices, touch gear Icon, and
tap to Unpair
3. Turn off Bluetooth, wait 10 seconds, turn on Bluetooth
• Then power on your DA2012B, and Bluetooth LED should flash
• You should now be able to connect to DA2012B via Bluetooth
4
DA2012B BACK PANEL
1
VOICINGS
Pressing the button selects from the available voicings (tunings)
for different applications:
- FLOOR Normal: standard tuning, for use as a floor monitor
- FLOOR Boost: boosts lows and highs, which can be useful for
low volume use, or to hear yourself better alongside other
musicians’ amps
- POLE Normal: standard tuning, for use on a pole, or when
standing vertically
- POLE Boost: boosts lows and highs, which can be useful for
low volume use, or to hear yourself better alongside other
musicians’ amps
2
CHANNEL 1, 2 and 3 KNOBS
These knobs set the volume for the inputs below them. Channel
3 knob sets the level of Bluetooth audio as well as the other
Channel 3 audio inputs.
3
BALANCED LINE INPUTS
Balanced or unbalanced line level sources can be connected here
4
BLUETOOTH AUDIO INPUT
Bluetooth audio input is automatically enabled each time you
turn the amplifier on, will automatically reconnect to the previous
Bluetooth audio source if it is available, and will otherwise be
available for Bluetooth pairing from a source audio device such as
a smartphone
- To pair, look for DA2012B from your Bluetooth audio source
device.
- LED is lit solid when currently paired, blinking when available for
pairing, and off if Bluetooth has been disabled by a press of the
Bluetooth Off button.
- On/Pair button forces any currently connected Bluetooth audio
source to disconnect, and makes the speaker available for
pairing.
- Off button disables Bluetooth. (Bluetooth will be re-enabled
next time you turn power off and on, or if you press the On/Pair
button.)
5
AUX INPUT
Audio from smartphones, computers and other consumer audio
devices can be connected here
6
BASS AND TREBLE KNOBS
Adjust the sound of your amplifier
7
MONO / STEREO MASTER / LINK IN SWITCH
- Mono: This DA2012B will output mono audio, and send mono
audio to the OUT jack so it’s available for any other amplifier or
sound system.
- Stereo Master: This DA2012B will operate as the master unit of
a Smart Stereo pair. Use a mic cable to connect this DA2012B’s
OUT to the LINK IN jack of a second DA2012B. All inputs should
be connected to the first master amplifier, which will also set the
volume and tone of both DA2012Bs.
- Link In: Use this setting for the second DA2012B of a Smart
Stereo pair. The audio from the LINK IN will be routed directly
to the power amp and speaker, with all other inputs and
controls being ignored.
8
OUT JACK
Configured by
7
switch
- Mono: sends out mono audio
- Stereo Master: sends out right audio, for second DA2012B’s
LINK IN
- Link In: sends out the same audio received at the LINK IN jack
9
LINK IN JACK
Activated only when
7
switch is set to LINK IN
10
FRONT LED SWITCH
- On: Front LED is lit white when power is on
- On/Limit: LED lights red when limiter is active, and otherwise is
lit white
11
Connect power cable here
12
If the DA2012B will not power on and you suspect its fuse
may have blown, turn off the power switch, and open the fuse
compartment using a small flat blade screwdriver. If metal strip in
fuse is broken, replace with T5AL 250V fuse.
13
Switches the power on and off
1
2
3
If limiter is continuously or frequently active, turn down Channel 1,
2 or 3 knobs to reduce volume
4
5
6
7 8
9
11
12
13
10
DA2012B ADVANCED DRUM AMPLIFIER
5
Amplifier
DSP
Selectable Voicing (Floor Normal, Floor Boost, Pole Normal, Pole Boost) and
Bass and Treble knobs all control the internal DSP to customize the sound
Limiter
Transparent, dynamic DSP limiter for ideal sound quality and system
protection at maximum volume
Smart Stereo
A pair of DA2012B amplifiers can be connected for unified volume and tone
control from the first master amplifier, with optimal distribution of mono and
audio signals between both amplifiers
Input 1
Stereo Line: Left/mono and right 1/4-inch TRS balanced/unbalanced
compatible audio line inputs
Input 2
Stereo Line: Left/mono and right 1/4-inch TRS balanced/unbalanced
compatible audio line inputs
Input 3
Stereo Line: Left/mono and right 1/4-inch TRS balanced/unbalanced
compatible audio line inputs
Aux: 1/8-inch mini TRS unbalanced input
Bluetooth Audio: with On/Pair and Off buttons plus LED
Link In XLR balanced +4dBv audio input
Out Jack XLR balanced +4dBv audio output
Power Output 2000 Watts Peak
Bass EQ Knob +/-12dB Shelf, 100Hz
Treble EQ Knob
+/-12dB Shelf at 10kHz
Volume volume control per channel
Power Input 115V/60 Hz
Features
Removable AC Power Cord
Front LED, configurable to indicate power or power/limiter
Voicing button and 4 voicing indicator LEDs
Speaker
Type 12˝ 2-way vented design
Frequency Response 40-20K Hz
Max SPL@1M 126dB
HF Driver Compression Driver, 8 Ohm
LF Driver 12˝ Driver, 4 Ohm
Cabinet Polypropolene, with rubber surfaced handles and feet
Grille 1.2mm steel
Suspension Points DA2012B Is Not Designed For Suspension
Pole Mount 35mm stand pole with M6 screw
Product Dimensions 14.2” x 14.2” x 24.1”
Dimensions and Weights
Packaging Size 18.1” x 18.1” x 28.1”
Net Weight 35 pounds
Gross Weight 45 pounds
SPECIFICATIONS
6
IMPORTANT SAFETY INSTRUCTIONS
Please keep this instruction manual for future reference and for the
duration of owning the Simmons DA2012B Advanced Drum Amplifier.
Please carefully read and understand the instructions inside this owner’s
manual before attempting to operate your new powered loudspeaker.
This instruction manual includes essential safety information regarding
the use and maintenance of the amplifier. Take special care to heed all
warning symbols and signs inside this manual and those printed on the
amplifier on the back of the loudspeaker.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE
AMPLIFIER TO WATER/MOISTURE, NOR SHOULD YOU OPERATE THE
AMPLIFIER NEAR ANY WATER SOURCE.
The exclamation point triangular symbol is intended to alert the user
to the presence of important operating and maintenance(servicing)
instructions in the user manual accompanying the Amplifier.
The lightning flash with an arrow triangular symbol is intended to alert
the user to the presence of non-insulated “dangerous voltage” within the
product’s enclosure, and may be of sufficient magnitude to constitute a
risk of electric shock.
WARNING
Handle the power supply cord with care.
Do not damage or deform it as it may cause electric shock or malfunction
when used. Hold the plug attachment when removing from wall outlet.
Do not pull on the power cord.
IMPORTANT SAFETY PRECAUTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions. DO NOT turn on the amplifier module
before connecting all other external devices.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.
11. Only use attachment/accessories specified by the manufacturer.
12. Use only the cart, stand, tripod, bracket or table specified
by the manufacturer, or sold with the apparatus. When
a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. POWER SOURCES – This product should be operated only from the
type of power source indicated on the rating label. If you are not
sure of the type of power supply to your home, consult your product
dealer or local power company.
16. WALL OR CEILING MOUNTING – The product should never be
mounted to a wall or ceiling.
17. Where the mains plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
18. OBJECT AND LIQUID ENTRY – Care should be taken so that objects
do not fall and liquids are not spilled into the enclosure through
openings.
19. Water and Moisture: This product should be kept away from direct
contact with liquids. The apparatus shall not be exposed to dripping
or splashing and that no objects filled with liquids, such as vases, shall
be placed on the apparatus.
20. Keep the speaker system out of extended or intense direct sun light.
21. No containers filled with any type of liquid should be placed on or
near the speaker system.
22. SERVICING – The user should not attempt any service to the speaker
and/or amplifier beyond that described in the operating instructions.
All other servicing should be referred to qualified service personnel.
23. VENTILATION – Slots and openings in the amplifier are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating. These openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should not be placed in a built-in installation such as a bookcase or
rack.
24. Protective earthing terminal: The apparatus should be
connected to a main socket outlet with a protective
earthing connection.
25. ACCESSORIES – Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the product.
Use only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product.
26. When moving or not using the appliance, secure the power cord
(e.g., wrap it with a cable tie). Be careful not to damage the power
cord. Before using it again, make sure the power cord has not been
damaged. If the power cord has been damaged at all, bring the unit
and cord to a qualified service technician for repair or replacement as
specified by the manufacturer.
27. LIGHTNING – For added protection during a lightning storm, or when
it is left unattended and unused for long periods of time, unplug it
from the wall outlet. This will prevent damage to the product due to
lightning and power-line surges.
28. REPLACEMENT PARTS – When replacement parts are required, be
sure the service technician has used replacement parts specified by
the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or
other hazards.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED PERSONAL
DA2012B ADVANCED DRUM AMPLIFIER
7
IMPORTANT SAFETY INSTRUCTIONS
To prevent electric shock, do not use a polarized plug with an extension
cord, receptacle or other outlet unless the blades can be fully inserted to
prevent blade exposure.
HEARING DAMAGE AND PROLONGED EXPOSURE TO
EXCESSIVE SPLs
Simmons DA2012B Advanced Drum Amplifiers are capable of producing
extremely loud volume levels that can cause permanent hearing damage
to performers, production crews or the audience. Hearing protection is
recommended during long-term exposure to high SPLs (sound pressure
levels).
Remember, if it hurts, it is definitely too loud! Long term exposure to
high SPLs first causes temporary threshold shifts; limiting your ability to
hear the actual loudness and exercise good judgment. Repeated long
term exposure to high SPLs will cause permanent hearing loss.
Please note the recommended exposure limits in the accompanying table.
More information about these limits is available on the US government
Occupational Safety and Health (OSHA) website at: www.osha.gov.
WARNING: To reduce the risk of fire or shock do
not expose this equipment to rain or moisture.
AVERTISEEMENT: Pour réduire les risques
d’incendie et d’électrocution, ne pas exposer ce
matérial à la pluie ou à l’humidité.
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE NE
PAS OUVRIR
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE NE
PAS OUVRIR
CAUTION: To reduce the risk of electric shock, do not
remove chassis. No user-serviceable parts inside.
Refer servicing to qualified service personnel.
AVERTISEEMENT: Pour réduire les risques d’incendie et
d’électrocution, ne pas exposer ce matérial à la pluie ou
à l’humidité.
WARNING: To reduce the risk of fire or shock do
not expose this equipment to rain or moisture.
AVERTISEEMENT: Pour réduire les risques
d’incendie et d’électrocution, ne pas exposer ce
matérial à la pluie ou à l’humidité.
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE NE
PAS OUVRIR
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE NE
PAS OUVRIR
CAUTION: To reduce the risk of electric shock, do not
remove chassis. No user-serviceable parts inside.
Refer servicing to qualified service personnel.
AVERTISEEMENT: Pour réduire les risques d’incendie et
d’électrocution, ne pas exposer ce matérial à la pluie ou
à l’humidité.
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.
WARNING: To reduce the risk of fire or shock do
not expose this equipment to rain or moisture.
AVERTISEEMENT: Pour réduire les risques
d’incendie et d’électrocution, ne pas exposer ce
matérial à la pluie ou à l’humidité.
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE NE
PAS OUVRIR
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE NE
PAS OUVRIR
CAUTION: To reduce the risk of electric shock, do not
remove chassis. No user-serviceable parts inside.
Refer servicing to qualified service personnel.
AVERTISEEMENT: Pour réduire les risques d’incendie et
d’électrocution, ne pas exposer ce matérial à la pluie ou
à l’humidité.
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING
AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE APPARATUS.
Permissible Noise Exposures (1)
Duration per day, hours Sound level dBA slow response
8 90
6 92
4 95
3 97
2 100
1.5 102
1 105
0.5 110
0.25 or less 115
8
CALL
TOLL FREE
888-621-4008
OR VISIT OUR WEBSITE AT: simmonsdrums.net
MISSING
damaged
parts?
assembly
questions?
WARRANTY
Two (2) Years limited warranty
Subject to the limitations set forth below, Simmons® hereby
represents and warrants that the components of this product
shall be free from defects in workmanship and materials,
including implied warranties of merchantability or fitness for a
particular purpose, subject to normal use and service, for three
(3) years to the original owner from the date of purchase.
Retailer and manufacturer shall not be liable for damages
based upon inconvenience, loss of use of product, loss of
time, interrupted operation or commercial loss or any other
incidental or consequential damages including but not limited
to lost profits, downtime, goodwill, damage to or replacement
of equipment and property, and any costs of recovering,
reprogramming, or reproducing any program or data stored
in equipment that is used with Simmons® products. This
guarantee gives you specific legal rights. You may have other
legal rights which vary from state to state. Some states do not
allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.
Simmons
P.O. Box 5111 Thousand Oaks, CA 91359-5111
All trademarks and registered trademarks mentioned herein are
recognized as the property of their respective holders.
FCC STATEMENT
1. Caution: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
2. Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined
by tuming the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician
for help.
Warning: Changes or modifications to this unit not expressly
approved by the part responsible for compliance could void
the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure
requirement. The device can be used fixed/mobile (min20cm)
exposure condition without restriction.
1904-19376886
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Simmons DA2012B Manuel utilisateur

Simmons
Marque
Simmons
Modèle
DA2012B
Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents