Honeywell HM506 Le manuel du propriétaire

Marque: Honeywell

Modèle: HM506

Catégorie: Humidificateurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

HM509
HM512

Hone_el|

TrueSTEA

omeowner's Manual

69-2286EF-01

Safety Definitions and Precautions

Must be installed by a trained, experienced technician.

Read these instructions carefully. Failure to follow these instructions can damage the product or cause a

hazardous condition.

Please read this manual completely. It is important that you understand how TrueSTEAM works, and how to

safely perform the required maintenance procedures. Read and understand all safety-related labels found on

and posted near the TrueSTEAM humidifier. These labels provide additional instructions and important

safety information.

Safety Definitions

These safety terms identify information you must read.

,_ CAUTION: Indicates a hazardous situation which, if not avoided, could cause bodily injury or

property damage.

_l_ WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Safety Precautions

Make sure you read and understand the following safety hazards before installing, using, or working

with theTrueSTEAM humidifier:

,, Do not d rect the steam nozzJe at people.

, Water inside lank can be very hot. Read the warning label on TrueSTEAM and make sure you

understand the hazards of scalding not water in the tank.

,, Scalding danger from draining water. When the water tank empties, draining water can be hot enougq

to cause injury. Make sure you know where the water exits the drain hose. Be certain hot water will not

pose a hazard to people or pets.

WARNING: Electrocution Hazard.

TrueSTEAM uses 120 volts AC, which can cause death or serious injury. Take precautions when servicing

TrueSTEAM or when removing the water tank or cover. If in doubt, unplug TrueSTEAM and disconnect

HVAC equipment power before servicing.

CAUTION: Heavy Equipment and Water Hazard.

Improper installation or misuse can cause death, blindness, and water damage to home, and heating

element failure. Be sure you know how to turn TrueSTEAM off, and how to drain the water tank safely.

CAUTION: Steam Condensation, Fire, and Freezing Water Hazard.

Can cause failure of fan or limit control, or result in water damage to home.

TrueSTEAM Humidification System 69-2286EF--01

Welcome!

Congratulations on your new humidifier.

The Honeywell TrueSTEAM humidification system provides the high performance and efficiency of steam, with

easier maintenance than traditional humidifiers.

We are sure TrueSTEAM will be a welcome addition to your home.

How is TrueSTEAM different from other humidifiers?

- The steam goes directly into your hot air supply duct, rather than evaporating from a wet pad, which

requires furnace temperature to produce humidity efficiently.

- TrueSTEAM delivers humidity independent of your furnace. This allows you to achieve ideal humidity levels

in your home, year-round.

- TrueSTEAM wastes less water than flow-through humidifiers.

- TrueSTEAM operates automatically, just like a thermostat, to keep your home's humidity at the desired level.

- TrueSTEAM is easy to maintain. Just clean the tank as instructed. The tank is easily accessible and does not

require tools to remove it.

What safety features does TrueSTEAM have?

- An interlock switch located inside the water tank shuts off 120 VAC power to TrueSTEAM when the tank

is removed.

- Three sets of sensors constantly monitor water level in the tank. The sensors prevent the tank from being

over-filled and from running dry.

How should I get started? Your TrueSTEAM must be installed by an HVAC Professional Installer. If the

TrueSTEAM has just been installed, it should either be running and humidifying your home, or waiting for a

humidity call from the humidity control provided.

Once TrueSTEAM is up and running, all you have to do is use the humidity control to change the humidity to

your desired comfort.

• Please read this manual completely for tips on getting the most out of your TrueSTEAM.

• Read }/our humidity control manual and make sure you know how to operate your system.

• If you have questions, now or later, please ask your installer or call Honeywell Customer Care

a_ 1-800-468-t 502 ...........

TrueSTEAM Humidification System 69-2286EF--01

How does TrueSTEAM work?

A call for humidity comes from the humidity control

provided with TrueSTEAM. The humidity control is

connected to TrueSTEAM, either with wires or by

wireless connection.

The heating element coil heats water in the tank to

the boiling point.

The resulting steam flows out of TrueSTEAM into

the hot air supply duct of your HVAC system. If

remote mounting is used, the steam flows through

an insulated steam hose from TrueSTEAM to your

supply duct.

Air flow from your furnace fan carries the moisture

throughout your home. Your furnace may or

may not be heating the air, depending on your

thermostat setting and TrueSTEAM configuration.

When humidity in your home reaches the setpoint,

the humidity call ends and TrueSTEAM stops

producing steam. The furnace fan may continue

to run until humidity in the duct is completely

distributed to your home.

m Sensors monitor water level in the tank. The built-in

solenoid valve opens and closes to automatically

refill the tank, as needed. During long periods of

inactivity, the tank will drain completely to prevent

water stagnating. The tank will automatically refill

when there is demand for humidity.

TrueSTEAM Humidification System 69-2286EF--01

Which TrueSTEAM model do l have?

TrueSTEAM is available in three sizes, each with a different humidifying capacity:

HM506 Delivers up to 6 gallons of water each day into your home. This _sgenerally suitable for homes

4.000 to t4.400 cubic feet in size.

HM509 Delivers up _o9 gallons of water each day into your home. It is generally suitable for homes

8.000 to 18.400 cubic feet in size.

HM512 Delivers up to 12 gallons of water each day into your home. This model is generally suitable for

komes 12.000 to 24.000 cubic feet in size.

The proper model for your home depends on many factors. Size of the area to be humidified, ceiling height,

window and insulation type, as well as your geographic area, all affect how much humidity your

home needs.

Some activities in your home may create heavier loads for TrueSTEAM. Vented fireplaces, high exhaust from

fans, or driers can reduce humidity in your home and make TrueSTEAM work harder.

Your Professional Installer or salesperson will have considered these and other factors when choosing the best

TrueSTEAM model for your unique situation.

This label displays the model number and date code

of your TrueSTEAM.

TrueSTEAM Humidification System 69-2286EF--01

Which humidity control do l have?

TrueSTEAM comes with a humidity control. Your humidity control will either be included in your home thermostat

(RedLINK Prestige or VisionPRO IAQ), or it will be a separate device (TruelAQ or H8908). You will use the

humidity control to set the desired humidity level for your home, and to turn TrueSTEAM on and off.

RedLINK Prestige TM High-Definition Color

• Advanced wireless control of air quality equipment

Automatically controls temperature, TrueSTEAM,

and other air quality equipment

Shows actual and desired humidity on an intuitive

digital display

Wireless sensor for displaying outdoor temperature

and humidity

Maintenance and service reminders

i........

VisionPRO TM IAQ

Automatically controls temperature, TrueSTEAM,

and other air quality equipment

Sensor for displaying outdoor temperature

Easy 7-day temperature programming on an

intuitive digital display

Maintenance and service reminders

TruelAQ TM

Automatically controls air quality equipment

Sensor for displaying outdoor temperature

and humidity

Shows actual humidity and desired setting

Maintenance and service reminders

H8908 Manual Control

Manual humidity control with intuitive

comfort settings

Integrated humidity chart for accurate control in

changing conditions

TrueSTEAM Humidification System 69-2286EF--01

How is my TrueSTEAM installed?

Your HVAC Professional Installer will install TrueSTEAM in a proper location in your home. The best location

depends on your furnace type and configuration, and how your living space is arranged around the furnace

ducts. Your TrueSTEAM wil! be either duct mounted or remote mounted,

Duct mounting. TrueSTEAM is installed directly onto

the supply (hot) air duct of your furnace. The steam

nozzle sends steam directly from TrueSTEAM into the

duct for distribution through your home.

Remote mounting. TrueSTEAM is installed some

distance away from your furnace supply duct. An

insulated hose carries steam from TrueSTEAM to a

suitable location on the supply duct.

Remote mounting is usually done when a suitable

mounting location can not be found on your

furnace duct.

TrueSTEAM Humidification System 69-2286EF--01

What TrueSTEAM parts do ! need to know?

Your TrueSTEAM installation includes the following parts and components that you should be familiar with:

M29679

M27981

...

A. Cold Water Connection with Shutoff Valve

Provides the connection from TrueSTEAM to your

home's cold water pipe. Your Professional Installer

may have used the saddle valve that came with

TrueSTEAM, or may have chosen a different type

of connection. This connection must include

a shutoff valve for you to turn off water flow to

TrueSTEAM, if necessary.

IMPORTANT: TrueSTEAM requires cold water.

Do not connect a hot water supply to TrueSTEAM

Water Supply Line

This 1/4-inch line brings cold water to TrueSTEAM

from a water pipe in your home. Your Professional

Installer may have used the plastic line provided or

a copper pipe, as appropriate.

C. In-line Water Filter

It is likely the installer provided a water filter on

the water supply line leading to TrueSTEAM.

This helps minimize mineral deposits forming

in TrueSTEAM's tank. For optimal performance,

replace this water filter once each humidification

season. See "How do I change the water filter?"

on page 19.

D. Shutoff Valve and Backflow Preventer

This valve was provided by Honeywell and is

required by code. It prevents water from flowing

backward in the water supply line.

TrueSTEAM Humidification System 69-2286EF--01

E, Power Cord

TrueSTEAM is plugged into a 120 volt AC

household electrical outlet. The power cord

provided is 6 feet long.

F, Water Drain Line

This 1/2-inch hose drains water from TrueSTEAM

to a drain in your home. The tank is drained

automatically when TrueSTEAM performs an

automatic flush cycle, and at the end of the

humidification season. You may also drain the tank

manually in order to clean the tank or perform

additional maintenance.

G. Safety Release Button

This button prevents the tank release lever from

accidentally moving forward and releasing the

water tank. Press and hold the button down to

move the lever forward.

H, Ventilation Holes

These holes provide airflow for the electronic

components inside the TrueSTEAM cover. Normal

maintenance includes keeping these holes clean.

TrueSTEAM Cover

TrueSTEAM wiring connections and electronic

components are located behind the cover. There

are no homeowner-serviceable parts here, and

the cover should only be removed by a qualified

HVAC Service Technician.

Jm Tank Release Lever

This lever locks the water tank in place on

TrueSTEAM. Press the safety release button, then

pull the lever forward to release the water tank

when removing for cleaning or service.

IMPORTANT: Only remove the tank after it is

completely empty. See "How do I clean the tank?"

on page 16.

Light Display

The six lights are on or blinking to indicate

TrueSTEAM's operational status and when service

is required. See "What do the lights tell me?" on

page 13.

Lm TrueSTEAM Buttons

The two buttons are the only controls located

on TrueSTEAM. They are seldom used by the

homeowner. (Remember, day-to-day operation is

done using your humidity control.) Use the Drain

button to manually drain the water tank. Use the

Go button to reset TrueSTEAM when restarting the

system. See "When will I press the Drain and Go

buttons?" on page 14.

M, Water Tank

The tank holds the water that TrueSTEAM heats and

converts to steam. The tank can be removed

for cleaning.

Hm Manual Shutoff Valve

Turn this valve by hand to either of two positions:

Lock: The valve will be locked during operation.

This turns the water supply on and locks the

solenoid valve in place. (TrueSTEAM uses the

solenoid valve to control water flow into the tank.)

Unlock: Turning the valve to "Unlock" seals the

bottom of the tank and the water supply to avoid

leaks when performing manual cleaning of the tank.

It also disengages the solenoid valve so that you

can push the solenoid back in its base to release

the tank. Once this is done, you can pull the tank

release lever forward to remove the tank

for cleaning. See "How do I clean the tank?" on

page 16.

TrueSTEAM Humidification System 69-2286EF--01

What should ! expect from my TrueSTEAM?

Honeywell wants to make sure you know what to expect from your new TrueSTEAM installation, Make sure you

discuss these items with your Professional installer:

Achieving Humidity Setpoint. It may take up to a week of continuous operation to initially achieve the

humidity setpoint. This depends on factors such as weather, size of home, furnishings in the home, and

insulation. Once this is achieved, TrueSTEAM should not have to run as much to maintain humidity.

Plastic or Rubber Odor. When the humidifier starts up after the initial installation, it is normal to smell a slight

plastic odor in the home. If the remote hose is used, there may be a slight rubber odor. These odors will go

away within a few days.

Ideal Humidity. 35% relative humidity in typical winter weather is considered ideal for indoor comfort by

industry experts. You can adjust to your own comfort or until there is condensation on the windows. Lower the

setpoint if condensation appears.

Unit Hot Humidifying. If TrueSTEAM is not running but the humidity is below the desired setting, the humidity

control may have a frost protection setting. See "What is a frost setting?" on page 12. Note that TrueSTEAM

will not humidify while in an automatic flush cycle.

Setpoint Not Reached. If humidity doesn't reach the setpoint, TrueSTEAM may be under-sized for the home.

This can be due to insulation, windows, arid climate, and other environmental factors. Also, the outdoor

temperature may be too low to maintain the humidity level. If the desired humidity is still not reached, then a

larger capacity TrueSTEAM may be needed.

Home Ventilation. Excessive ventilation exhausts humidified air and replaces it with dry air. This can make it

hard to maintain the humidity setpoint. If you are installing a ventilator, use a solution that retains moisture. An

Energy Recovery Ventilator (ERV) is recommended.

Cleaning Required Light. If the Cleaning Required light is on, clean TrueSTEAM using the steps found in

"How do I clean the tank?" on page 16,TrueSTEAM will continue to run normally while the Cleaning Required

light is on.

,, Hard Water. Your home's water hardness determines how often TrueSTEAM must be cleaned and how often

the water filter needs to be replaced.

Energy Consumption. You may notice a slight increase in overall energy consumption when operating any

humidifier. However, TrueSTEAM will make the home feel warmer. This allows you to lower the temperature

setting on the thermostat. Every degree lower on the thermostat can save up to 3% on heating costs.

lO TrueSTEAM Humidification System 69-2286EF--01

How do ! operate TrueSTEAM?

Once TrueSTEAM is installed and running, operation is automatic. Use the humidity control provided to make any

changes to the setpoint, or to turn TrueSTEAM on or off.

Your Professional Installer configured TrueSTEAM so that it only creates steam when conditions in your HVAC

system are right. Steam can only be produced when your system fan is blowing air through the duct.

Be sure to read the manual that came with your humidity control. Ask your Professional Installer if you have

questions about how to operate TrueSTEAM.

How do I use the humidity control? Whenever humidity in the home is lower than the humidity control's

setpoint, the control will call for humidity. Some controls will also monitor outdoor conditions to ensure indoor

humidity does not condense on windows and walls. Refer to the manual provided with your humidity control

for instructions on setting the control. There are two different types of humidity control:

Thermostat with integrated humidity

control (such as VisionPRO IAQ or

RedLINK Prestige).

,o... 72°

This arrangement allows you to control

your furnace, central air conditioning, and

TrueSTEAM all with one device.

Humidity control separate from the

thermostat(sUchastheHago8

With this arrangementl you wil use your current

therm0stat to contr01 y0ur furnace and central

air conditioning. Use the separate humidity

control to control your TrueSTEAM. .........................

TrueSTEAM Humidification System 69-2286EF--01 11

What should my humidity setpoint be? The outdoor air temperature affects how much humidity can be

retained by the air in your home. Use this table as a starting point. Then adjust the humidity control to your

own comfort or until condensation appears on the windows.

Outdoor Recommended Relative

Temperature Humidity Setting

..................................................... • ,.,H.....,.

2oF 7° o

0 (- C) 35

>20°F (-1oC)....................... 35% ..................

What is a frost setting? Some humidity controls (such as Prestige, VisionPRO IAQ, and True IAQ) contain

a Window Frost Protection feature which limits humidity output based on outdoor conditions. For example,

on colder days, the air in your home can hold less humidity. The humidity control automatically lowers the

humidity setpoint accordingly, to prevent frost from appearing on the inside of your windows.

Lower the frost setting by one value each morning that you see frost or condensation on windows. Allow 24

hours for the new setting to take effect before re-adjusting. Once you have this set to a comfortable level

without condensation, you will not need to adjust further. You can adjust your humidity setpoint without

worrying about condensation.

Less Humidity

Loosehome/ single-panewindows

More Humidity

Tight home/triple-panewindows

1 2 3 4 5 6 7 8 9

M27982

Manual humidity controls (such as the H8908) do not have built-in frost settings. They require you to adjust

the humidity setpoint when the outdoor temperature changes. Use higher humidity setpoints when the

temperature is warmer, and lower setpoints when the temperature is cooler.

12 TrueSTEAM Humidification System 69-2286EF--01

What do the lights tell me?

The six lights show TrueSTEAM status and indicate when service needs to be performed.

Power (Green). On indicates the power cord is

plugged in.

Humidifying (Green).

Lit - TrueSTEAM is actively heating water and creating

steam.

Blinking - TrueSTEAM is resetting or filling. This is

usually done when plugging in the power cord, and

lasts for about 3 minutes. You can press the Go button

to reset TrueSTEAM immediately.

Dark - TrueSTEAM is in Ready mode - it can heat

water and produce steam when a humidity call comes

from the control.

Empty (Green). When on, the water tank is empty and

can be removed for manual cleaning.

Service (Red).

Blinking - The number of blinks (1-18) shows the type

of fault TrueSTEAM has detected. See "What should I

do if the Service light is blinking?" on page 22.

Draining (Yellow).

Blinking - TrueSTEAM is flushing water from the tank

for manual cleaning. See "What is the automatic flush

cycle?" on page 15.

Cleaning Required (Yellow).

On - Indicates that the tank needs to be cleaned

manually. See "How do I clean the tank?" on page 16.

M29628

TrueSTEAM Humidification System 69-2286EF--01 13

When will l press the Drain and Go buttons?

The two buttons are used when starting TrueSTEAM and to manually drain the tank.

Drain Button: Press and hold to drain water from the

TrueSTEAM tank. See "How do I clean the tank?" on

page 16.

When the Draining light is blinking, TrueSTEAM is

actively flushing water during a manual drain.

Go Button: Press to start or reset TrueSTEAM when

the Humidifying light is blinking.

Pressing and holding Go also clears the blinking

Service light and stops water draining from the tank.

Drain and Go Button: Pressing and holding both the

Drain and Go buttons in at the same time will interrupt

the water cooling cycle and immediately drain

the tank.

M29628

IMPORTANT: Pressing and holding the Drain and Go

buttons together--when the Draining light is already

on--causes TrueSTEAM to empty the tank, regardless

of water temperature. Make sure the drain outlet can

handle up to 212°F (100°C), or wait at least 45 minutes

to allow the water to cool before using

this feature.

14 TrueSTEAM Humidification System 69-2286EF--01

What is the automatic flush cycle?

TrueSTEAM automatically flushes out the water tank

during the humidifying season. In the automatic

flush cycle, cold water enters the tank while water

is being emptied through the drain line. The action

of simultaneous filling and draining cools the water

to a safe draining temperature, it also dilutes water

hardness concentration to reduce mineral deposits

from forming in the tank.

At the end of the automatic flush cycle, TrueSTEAM

refills the tank with fresh water, and automatically

returns to normal operation.

M29669

Automatic flush is performed regularly, based on the number of hours that TrueSTEAM heats water and produces

steam. Automatic flush can be set to occur at any of the following intervals:

Autoflush Intervals

8 hours (recommended for hard wa[er)

12 hours (factory setting)

20 hours Cwhen a wa[er softener is installed)

30 hours (when an optional RO filter is installed)

Your Professional Installer set TrueSTEAM to flush at the appropriate interval for your installation. During any

service call, the automatic flush interval can be changed, if desired.

TrueSTEAM Humidification System 69-2286EF--01

Why do ! need to manually clean the tank?

Manua! cleaning is needed at least once each season to clean out the mineral deposits that remain in the tank

after automatic flushing. Manual cleaning is easy - just empty and remove the water tank and clean the interior

components, Then re-assemble and start TrueSTEAM up again,

When should I clean the tank? TrueSTEAM should be manually cleaned at least once every 5 months.

(Hard water may require more frequent cleaning.) The Cleaning Required light turns on when the tank needs

manual cleaning. TrueSTEAM will still operate normally when the Cleaning Required light is on. The light will

turn off when you have cleaned the tank and re-started TrueSTEAM.

Note: The Cleaning Required light turns on when the tank drains too slowly during a manual flush cycle. (This is probably due to tank sediment.) TrueSTEAM

will still operate as normal. If during the next manual flush cycle, the tank drains normally, the Cleaning Required light will stop blinking.

How do I clean the tank? Follow these steps to manually clean TrueSTEAM:

Press the Drain button to initiate a flush cycle and

empty the water tank. You will know the tank is

draining when the Draining light is blinking.

Wait for the Empty light to turn on. (It takes about 45

minutes for the tank to drain.) This indicates that the

water has finished draining.

IMPORTANT: You can stop a manual flush once the

cycle has started by pressing and holding the Drain

button while the Draining light is already blinking. The

tank will refill and TrueSTEAM will return to normal

operation in about 5 minutes,

Turn the manual shutoff valve at the tank bottom to the

"Unlock" position.

Grip the white water valve arm and push it back to

disconnect it from the tank.

M29671

16 TrueSTEAM Humidification System 69-2286EF--01

First, firmly grip the tank bottom. Then push down the

safety release button.

Pull the latch forward to release the tank.

Note: The latch remains attached to TrueSTEAM and is not removed with

the tank.

Remove the tank.

Remove the sediment screen from the bottom of

the tank.

Use tap water to flush loose minerals from the tank

and sediment screen:

• For a more thorough cleaning, soak tank in warm

water. Then rinse clean. Tank is dishwasher safe.

Honeywell recommends CLR®,LimeAway ®,

or white vinegar for cleaning. Do not use

hydrocarbon- or oil-based cleaners.

Unplug the TrueSTEAM, and carefully rub minerals off

the heating element and reservoir walls.

Scouring pads suitable for non-stick pots or pans

may be used to clean the TrueSTEAM reservoir

walls and components within the tank.

For more thorough element cleaning, Honeywell

recommends soaking with CLR®, LimeAway ®, or

white vinegar. Do not use hydrocarbon- or oil-

based cleaners.

TrueSTEAM Humidification System 69-2286EF--01 17

How do I reassemble and start up TrueSTEAM? Follow these steps to reassemble the tank and start up

TrueSTEAM after cleaning:

Attach tank by raising the latch.

Pull the white water valve forward to connect to the

the black spool. Then turn the manual shutoff valve to

the "Lock" position.

M29675

M29676

Plug in the power cord.

The Power light will be on at start-up. If the humidity

control is also actively calling for humidity, the

Humidifying light will blink. This indicates that

TrueSTEAM is waiting to act on the call to allow time

for the tank to be fully connected.

M29677

Press the Go button to make TrueSTEAM ready

for use. You must actively call for humidity from the

humidity control for TrueSTEAM to produce steam.

Note: You don't have to press the Go button after pJugging in the power cord.

TrueSTEAM will wait for 5 minutes and then automatically reset itself.

18 TrueSTEAM Humidification System 69-2286EF--01

How do ! change the water filter?

Your HVAC Professional Insta!ler chose one of these two in-line water filters for use with your TrueSTEAM The

selection was based on the hardness of your home's water supply, Both types of filter must be replaced at least

once every humidification season:

Polyphosphate water filter with backflow preventer.

Reverse osmosis (RO) filter with backflow preventer.

M29683

Changing the in-line polyphosphate filter. Your Professional Installer will have secured the water filter and

backflow preventer valve in a place where you can reach them. Follow the water supply line from TrueSTEAM

to find the filter.

Turn the water supply off at the saddle valve or

T-fitting and manual shutoff valve.

Press down the filter collar ring and pull out the 1/4-

inch water line from each side of the filter.

Insert the 1/4-inch line into a new filter. Apply a

modest pull to ensure a tight fit.

Be sure to install the new filter correctly. The arrows on

the filter must point to TrueSTEAM.

Secure the new filter in place, using the bracket or

strap that your Installer provided.

kAg_A

TrueSTEAM Humidification System 69-2286EF--01

La page charge ...

Honeywell HM506 Le manuel du propriétaire

Marque: Honeywell

Modèle: HM506

Catégorie: Humidificateurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

HM509
HM512

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell HM506 Owner's manual

Honeywell HM506 Le manuel du propriétaire

Ce manuel convient également à

Honeywell HM506 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents