Sony VPL-XW7000 Mode d'emploi

Setup Guide_______________

Manuel de configuration __

Guía de configuración _____

Installationsanleitung _____

Guida di configurazione ___

C:\Users\kazuyuki-handa\Desktop\Condor_SG\21_SYQ\5038072211\5038072211VPLXW7000SYQ\01COV-

VPLXW7000SYQ\01GB01COV.fm

masterpage: Cover

VPL-XW7000

5-038-072-21(1)

Video Projector

5-038-072-21(1)

VPL-XW7000

masterpage: cover4.print

5-038-072-21(1)

VPL-XW7000

Printed in China

GB 2

This Setup Guide explains the installation and basic operations for projecting pictures.

Before operating the unit, please read this manual thoroughly and retain it for future reference.

Refer to “About Indicators” as necessary.

For details on the operations, refer to the Help Guide (Web operating instructions).

About This Manual

Preparing ....................................................................Page 9

Installing the Unit ..................................................... Page 10

Connecting the Unit .................................................. Page 12

Projecting.................................................................. Page 13

About Indicators........................................................................................Page 14

Dimensions................................................................................................Page 15

Step 1

Step 2

Step 3

Step 4

Manuals supplied

Setup Guide (this document)

Explains the installation and basic operations for projecting pictures.

Help Guide (Web operating instructions)

Explains the features of the unit and how to use in detail. You can view the Help

Guide on a smartphone or computer.

https://rd1.sony.net/help/vpl/xw5000/en/

3 GB

When using the product, do not use it for

purposes other than those described in the

instruction manual.

WARNING

To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified personnel

only.

WARNING

When installing the unit, incorporate a readily

accessible disconnect device in the fixed wiring, or

connect the power plug to an easily accessible

socket-outlet near the unit. If a fault should occur

during operation of the unit, operate the

disconnect device to switch the power supply off,

or disconnect the power plug.

CAUTION

For safety, do not connect the connector for

peripheral device wiring that might have excessive

voltage to the following port:

LAN

WARNING

1. Use the approved Power Cord (2-core mains

lead) / Appliance Connector / Plug that

conforms to the safety regulations of each

country/region if applicable.

2. Use the Power Cord (2-core mains lead) /

Appliance Connector / Plug conforming to the

proper ratings (Voltage, Ampere).

If you have questions on the use of the above

Power Cord / Appliance Connector / Plug, please

consult a qualified service personnel.

IMPORTANT

The nameplate is located in the following location

on the unit.

Side

CAUTION

– Danger of explosion if battery is incorrectly

replaced. Replace only with the same or

equivalent type recommended by the

manufacturer.

– When you dispose of the battery or the product,

you must obey the law in the corresponding area

or country. Do not dispose of the battery or the

product in a fire or a hot oven, or mechanically

crush or cut the battery. It may explode or cause

a fire. Do not subject the battery to extremely

low air pressure that may result in an explosion

or the leakage of flammable liquid or gas.

– Do not place the battery in a high temperature

place, such as under direct sunlight or near fire.

It may ignite, explode, or cause a fire. Do not

immerse or wet the battery in water or seawater.

This may cause an electric shock.

CAUTION

The following size and number of batteries are

required for the remote control.

Size: AA (R6)

Number of battery(ies): Two pieces

To avoid risk of explosion, use only the following

type of battery.

Manganese batteries

This symbol is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

For kundene i Norge

Dette utstyret kan kobles til et IT-

strømfordelingssystem.

WARNING: Do not look into the lens while in use.

Caution

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

Caution

The use of optical instruments with this product

will increase eye hazard.

IEC 60825-1:2014

CLASS 1 LASER PRODUCT

As with any bright light source,

do not stare into the beam, RG2

IEC 62471-5:2015.

English

GB 4

För kunderna i Sverige

VARNING: Titta aldrig in i projektorns lins medan

den används.

Försiktighet!

Användandet av kontroller eller justeringar eller

utförandet av andra procedurer än de som

specificeras häri kan resultera i exponering av

farlig strålning.

Försiktighet!

Användandet av optiska instrument med denna

produkt ökar risk för ögonskada.

Location information of the labels

Light source specifications

5.2 W laser diodes × 24

Wavelength: 450 - 460 nm

Beam divergence angle from lens of this unit

Zoom maximum: α = 39.9°

Zoom minimum: α = 25.5°

Do not place any object in front of the lens that

may block the light during projection. Heat from

the light may damage the object.

IEC 60825-1:2014

LASERPRODUKT AV KLASS 1

Precis som med alla starka

ljuskällor bör man inte titta

direkt i strålen, RG2 IEC 62471-

5:2015.

RG2 CAUTION PICTOGRAM

CLASS 1 LABEL

Laser emission port

5 GB

Precautions

On safety

Check that the operating voltage of your unit is

identical with the voltage of your local power

supply.

Should any liquid or solid object fall into the

cabinet, unplug the unit and have it checked by

qualified personnel before operating it further.

Unplug the unit from the wall outlet if it is not to

be used for several days.

To disconnect the cord, pull it out by the plug.

Never pull the cord itself.

The wall outlet should be near the unit and

easily accessible.

The unit is not disconnected to the AC power

source (mains) as long as it is connected to the

wall outlet, even if the unit itself has been turned

off.

Do not look into the lens while in use.

Do not place your hand or objects near the

ventilation holes. The air coming out is hot.

On preventing internal heat build-up

After you turn off the power with the / (On/

Standby) button, do not disconnect the unit from

the wall outlet while the cooling fan is still running.

Caution

This unit is equipped with ventilation holes

(intake/exhaust). Do not block or place anything

near these holes, or internal heat build-up may

occur, causing picture degradation or damage to

the unit.

On repacking

Save the original shipping carton and packing

material; they will come in handy if you ever have

to ship your unit. For maximum protection, repack

your unit as it was originally packed at the factory.

On watching 3D video images

Safety precautions

If you observe flickering or flashing, turn off the

lighting in the room.

Not for use by children without proper adult

supervision.

For the customers in the U.S.A.

SONY LIMITED WARRANTY - Please visit http://

www.sony.com/psa/warranty for important

information and complete terms and conditions

of Sony’s limited warranty applicable to this

product.

For the customers in Canada

SONY LIMITED WARRANTY - Please visit http://

www.sonybiz.ca/pro/lang/en/ca/article/

resources-warranty for important information

and complete terms and conditions of Sony’s

limited warranty applicable to this product.

For the customers in Europe

Sony Professional Solutions Europe - Standard

Warranty and Exceptions on Standard Warranty.

Please visit https://pro.sony/support-services/

primesupport/support-professional-solutions-

europe-standard-product-warranty for

important information and complete terms and

conditions.

For the customers in Korea

SONY LIMITED WARRANTY - Please visit http://

bpeng.sony.co.kr/handler/BPAS-Start for

important information and complete terms and

conditions of Sony’s limited warranty applicable

to this product.

GB 6

On inspection of light source related parts

Since the unit uses a laser, when adjusting or

inspecting the light source related parts, particular

attention and a safe environment are necessary.

Be sure to consult with qualified Sony personnel

(charged).

Note on leaving unused for long periods

If the unit is not used for a long period of time,

malfunction or a drop in performance can occur.

To avoid this, periodically turn on the power and

operate the unit.

On LCD Projector

The LCD projector is manufactured using high-

precision technology. You may, however, see tiny

black points and/or bright points (red, blue, or

green) that continuously appear on the LCD

projector. This is a normal result of the

manufacturing process and does not indicate a

malfunction.

Also, when you use multiple LCD projectors to

project onto a screen, even if they are of the same

model, the color reproduction among projectors

may vary, since color balance may be set

differently from one projector to the next.

On condensation

If the room temperature where the projector is

installed changes rapidly, or if the projector is

moved suddenly from a cold to a warm place,

condensation in the projector may occur. As the

condensation may cause malfunction, be careful

in adjusting temperature settings of the air

conditioner. If condensation occurs, leave the

projector turned on for about two hours before

use.

Notes on security

SONY WILL NOT BE LIABLE FOR DAMAGES OF

ANY KIND RESULTING FROM A FAILURE TO

IMPLEMENT PROPER SECURITY MEASURES ON

TRANSMISSION DEVICES, UNAVOIDABLE DATA

LEAKS RESULTING FROM TRANSMISSION

SPECIFICATIONS, OR SECURITY PROBLEMS OF

ANY KIND.

Depending on the operating environment,

unauthorized third parties on the network may

be able to access the unit. When connecting the

unit to the network, be sure to confirm that the

network is protected securely.

From a safety standpoint, when using the unit

connected with the network, it is strongly

recommended to access the Control window via

a Web browser and change the access limitation

settings from the factory preset values.

Also, it is recommended that you set a password

with a sufficiently long character string that is

hard to guess by others, and that you store it

safely.

Do not browse any other website in the Web

browser while making settings or after making

settings. Since the login status remains in the

Web browser, close the Web browser when you

complete the settings to prevent unauthorized

third parties from using the unit or harmful

programs from running.

When connecting this product to a network,

connect via a system that provides a protection

function, such as a router or firewall. If

connected without such protection, security

issues may occur.

Do not place this product close to medical devices

This product (including accessories) has magnet(s)

which may interfere with pacemakers,

programmable shunt valves for hydrocephalus

treatment, or other medical devices. Do not place

this product close to persons who use such

medical devices. Consult your doctor before using

this product if you use any such medical device.

SONY WILL NOT BE LIABLE FOR DAMAGES OF

ANY KIND RESULTING FROM THE USE OF THIS

UNIT FOR PURPOSES OTHER THAN GENERAL

HOME USE, EITHER DURING THE WARRANTY

PERIOD OR AFTER EXPIRATION OF THE

WARRANTY.

7 GB

Notes on Installation and

Usage

Do not place the unit in the following situations,

which may cause malfunction or damage to the

unit.

Near walls

To maintain the performance and reliability of the

unit, leave space between walls and the unit as

illustrated.

Note that the wall on the ventilation holes side

may become hot.

Air from air conditioners or the ventilation holes of

this unit or other devices, may cause oscillation on

the screen. Be sure not to install this unit in the

area where the air from air conditioners or the

ventilation holes of these devices reach to the

front side of this unit.

Poorly ventilated location

Leave space of more than 30 cm (11 7/8 inches)

around the unit.

Hot and humid

Locations subject to direct cool or warm air from

an air-conditioner

Installing the unit in such a location may cause a

malfunction of the unit due to moisture

condensation or rise in temperature.

Near a heat or smoke sensor

Malfunction of the sensor may occur.

Very dusty and extremely smoky locations

Do not do any of the following while using the

unit.

Tilting front/rear and left/right

Avoid using the unit tilted at an angle, as shown in

the following illustrations.

Do not install the unit anywhere other than on a

level surface or on the ceiling. Installing the unit in

such a location may result in uneven color

uniformity.

Unsuitable installation

30 cm

(11 7/8 inches)

30 cm

(11 7/8 inches)

5 cm (2 inches)

15 cm (6 inches)

30 cm

(11 7/8 inches)

30 cm

(11 7/8 inches)

Unsuitable Conditions

GB 8

If the unit is tilted up or down, the image on the

screen may be trapezoidal. Position the unit so

that the lens is parallel to the screen.

When installing the unit at high altitudes

When using the unit in a location at an altitude of

1,000 m (approx. 3,280 feet) or higher,

appropriately set “High Altitude Mode” in the

Setup menu. Failing to do so could have

adverse effects, such as reducing the reliability of

certain components.

Never mount the projector on the ceiling or

move it by yourself. Be sure to consult with

qualified Sony personnel (charged).

When installing the unit on a ceiling, be sure to

use a safety wire, etc., to prevent the unit from

falling. Entrust the installation to an experienced

contractor or installer.

For dealers

Be sure to secure the cabinet cover firmly when

installing to the ceiling firmly.

License Notice

Refer to “Notice on the Software” in the Help

Guide and read the contents of the license.

Safety precautions for installing the unit on

a ceiling

15° or more

15° or

more

10° or

more

10° or

more

15° or

more

9 GB

Preparing

Check the carton to make sure it contains the

following items:

Remote control RM-PJ24 (1)

Size AA (R6) batteries (2)

Lens cap (1)

When you purchase the projector, a lens cap is

on the lens.

AC power cord (1)

Setup Guide (this manual) (1)

Caution when handling the remote control

Handle the remote control with care. Do not drop

it, and do not step on or spill liquids on it.

Do not place the remote control in a location

near a heat source, a place subject to direct

sunlight, or a damp room.

Remove the lens cap before you use the projector.

Notes on the lens cap

When removing the lens cap

When removing the lens cap, hold the parts other

than the catches and pull it toward you. If you pull

while holding the catches, the lens may be

damaged.

When attaching the lens cap

When attaching the lens cap, be sure to hook the

catches of the lens cap on the notches of the lens

to prevent it from falling out.

The positions of the notches on the lens may differ from

the ones shown in the figure.

Preparing

Step 1

Checking the Supplied Accessories

Inserting the Batteries into the Remote

Control

Insert the batteries  side first.

Push and slide to open.

Removing the Lens Cap

Note

Catches

Notch

Catch

GB 10 Installing the Unit

1Position the unit so that the lens is parallel to

the screen.

2After connecting the AC power cord to the

unit, plug the AC power cord into a wall outlet.

After connecting the AC power cord to the unit, the

ON/STANDBY indicator may blink in orange.

You may not be able to control the unit while the

indicator is blinking, but this is not a malfunction. Wait

until it stops blinking and remains lit in red.

3Press the / (On/Standby) button to turn on

the unit.

4Project an image on the screen, then adjust

the focus, size, and position.

Adjust the focus.

Press the LENS ADJUSTMENT (FOCUS) button

to display the Lens Focus adjustment window

(test pattern). Then adjust the focus of the

picture by pressing the /// button.

Adjust the picture size.

Press the LENS ADJUSTMENT (ZOOM) button to

display the Lens Zoom adjustment window

(test pattern). Then adjust the size of the

picture by pressing the /// button.

Adjust the picture position.

Press the LENS ADJUSTMENT (SHIFT) button to

display the Lens Shift adjustment window

(test pattern). Then adjust to the proper

position of the picture by pressing the //

/ button.

Do not touch the lens when you adjust the image position.

Your fingers may be pinched when the lens extends/

retracts.

To adjust the tilt of the installation surface

If the unit is installed on an uneven surface, use

the front feet (adjustable) to keep the unit level.

Note that if the unit is tilted up or down, the projected

image will be distorted in a trapezoidal shape.

Be careful not to pinch your fingers when rotating the

front feet (adjustable).

Installing the Unit

Step 2

Note

Rear of the unit

ON/STANDBY

Front of the unit

Lights in red.

ON/STANDBY

Front of the unit

The ON/STANDBY indicator flashes

in green, then it lights in green.

Note

Notes

Turn to adjust.

Front feet (adjustable)

11 GB

Installing the Unit

Lens adjustment window (test pattern)

The dashed lines show the angle of view of each aspect

ratio.

4:3

1.85:12.35:1

For more information, refer to “Installation and

Connections” in the Help Guide.

GB 12 Connecting the Unit

When making connections, be sure to do the following:

Turn off all devices before making any connections.

Use the proper cables for each connection.

Insert the cable plugs firmly; Loose connections may reduce performance of picture signals or cause a

malfunction. When unplugging a cable, be sure to grip the plug, not the cable itself.

For more information, refer also to the instruction manual of the device to be connected.

Connecting the Unit

When you monitor and control the projector via the network, access the Setup page of the projector

(refer to “Using Network Features” in the Help Guide) via a Web browser and enable the desired control

protocol.

Step 3

HDMI cable (not supplied)

Right side of the unit

AV amplifier Speakers

Computer

Equipment with HDMI

output connectors

to HDMI output

: Video signal flow Use a Premium High Speed HDMI cable on which the cable type logo is

specified.

to HDMI input

For more information, refer to “Installation and

Connections” in the Help Guide.

13 GB

Projecting

1Turn on both the unit and the device

connected to the unit.

2Press INPUT to display the input palette on the

screen.

3Select the device from which you want to

display images.

Press INPUT repeatedly or press //

(enter) to select the device from which to

project.

1Press the / (On/Standby) button.

The message “POWER OFF?” appears.

2Press the / (On/Standby) button again

before the message disappears.

The ON/STANDBY indicator flashes in green

and the fan continues to run to reduce the

internal heat.

The fan stops and the ON/STANDBY indicator

changes from flashing green to remaining red.

The power is turned off completely, and you can

disconnect the AC power cord.

Never disconnect the AC power cord while the indicator is

flashing.

Tip

You can turn off the unit by holding the / (On/Standby)

button for about 1 second, instead of performing the above

steps.

Press one of the CALIBRATED PRESET buttons.

Projecting

Step 4

Projecting the Picture

Turning Off the Power

Note

Selecting the Picture Viewing Mode

Setting items Description

CINEMA FILM 1

(Cinema Film 1)

Image quality suited for reproducing

the wide dynamic and clear images

typical of master positive film.

CINEMA FILM 2

(Cinema Film 2)

Image quality suited for reproducing

the rich tone and color typical of a

movie theater, based on “Cinema Film

1.”

REF (Reference) Image quality suited for reproducing

the original image quality faithfully, or

to enjoy the image quality without

any adjustment.

TV (TV) Image quality suited for watching TV

programs, sports, concerts, and other

video images.

PHOTO (Photo) Image quality suited for viewing still

images taken with a digital camera

and other devices.

GAME (Game) Image quality suited for gaming, with

well-modulated colors and fast

response.

BRT CINE

(Bright Cinema)

Image quality suited for watching

movies in a bright room.

BRT TV

(Bright TV)

Image quality suited for watching TV

programs, sports, concerts, and other

video images in a bright room.

USER (User) You can set and adjust the image

quality to suit your taste, then you can

save the setting. The default setting is

the same as “Reference.”

IMAX Enhanced Image quality suited for watching

IMAX Enhanced contents.

Press the MENU button and select

from “Calib. Preset” in the Picture

menu.

CALIBRATED PRESET buttons

For more information, refer to “Projecting” in the

Help Guide.

GB 14 About Indicators

About Indicators

The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble with your projector.

If there is any problem or an error message appears on the screen, refer to “Error Handling” in the Help

Guide.

If the symptom persists even after carrying out the above methods, consult with qualified Sony personnel.

If the indicator starts flashing in a way of other than the above, turn off, and then turn on the power with the / (On/

Standby) button on the remote control or control panel of the unit.

If the symptom is shown again, consult with qualified Sony personnel.

Flashing/Lighting indicators The number of

flashes

Cause and Remedy

Three times The unit does not light properly due to an abnormality of the light

source and light source power. Turn off, then turn on the power after a

while.

If the symptom persists, consult with qualified Sony personnel.

Twice The internal temperature is unusually high. Check to ensure that

nothing is blocking the ventilation holes and the unit is not being used

at high altitudes.

Three times The fan is broken. Consult with qualified Sony personnel.

Note

ON/STANDBY

WARNING

indicator

ON/STANDBY

indicator

ON/STANDBY

WARNING

(Flashes in red)(Lights in red)

ON/STANDBY

WARNING

Both indicators flash

(Flashes in red) (Flashes in red)

If there is any problem or an error message

appears on the screen, refer to “Error Handling” in

the Help Guide.

15 GB

Dimensions

Front

Unit: mm (inches)

Bottom

Unit: mm (inches)

460 (18

1

/

8

)

111

(4

3

/

8

)

210.1

(8

9

/

32

)

5

(

3

/

16

)

Center of the lens

260 (10 1/4)

89.5

(3 17/32)

73.5

(2 29/32)

8 (5/16)

68

(2 11/16)

424.8 (16 23/32)

516.2 (20 5/16)

146.8

(5 25/32)

150.6

(5 15/16)

24.1 to 17 *

(15/16 to 21/32)

Holes for ceiling mount

(M5, Depth 8 (5/16))

Front of the cabinet

* Varies depending on how focus is adjusted.

GB 16 Dimensions

Holes for the ceiling mount

Use the screws with a length of 6.4 mm (1/4 inches, minimum) to 8.0 mm (5/16 inches, maximum) for the ceiling mount.

Recommended tightening torque (tension when turning a screw towards the direction of rotation): 1.4 ± 0.2 N-m

Note

Unit

Insert nut (M5)

Screw hole

The minimum

length of screw

The maximum

length of screw

17 GB

FR 18

Le Manuel de configuration décrit l’installation et les procédures de base de projection des images.

Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et le conserver pour future référence.

Reportez-vous à la section « À propos des indicateurs », le cas échéant.

Pour plus d’informations sur l’utilisation, reportez-vous au Guide d’aide (Mode d’emploi en ligne).

À propos de ce manuel

Préparation ...............................................................Page 25

Installation de l’appareil ..........................................Page 26

Raccordement de l’appareil......................................Page 28

Projection..................................................................Page 29

À propos des indicateurs...........................................................................Page 31

Dimensions............................................................................................... Page 32

Étape 1

Étape 2

Étape 3

Étape 4

Manuels fournis

Manuel de configuration (ce document)

Décrit l’installation et les procédures de base de projection des images.

Guide d’aide (Mode d’emploi en ligne)

Décrit les fonctionnalités de l’appareil et leur utilisation détaillée. Vous pouvez

afficher le Guide d’aide sur un smartphone ou un ordinateur.

https://rd1.sony.net/help/vpl/xw5000/fr/

19 FR

N’utilisez pas ce produit à des fins autres que

celles décrites dans le manuel d’instructions.

AVERTISSEMENT

Afin de réduire les risques d’incendie ou

d’électrocution, ne pas exposer cet appareil à la

pluie ou à l’humidité.

Afin d’écarter tout risque d’électrocution, garder

le coffret fermé. Ne confier l’entretien de

l’appareil qu’à un personnel qualifié.

AVERTISSEMENT

Lors de l’installation de l’appareil, incorporer un

dispositif de coupure dans le câblage fixe ou

brancher la fiche d’alimentation dans une prise

murale facilement accessible proche de l’appareil.

En cas de problème lors du fonctionnement de

l’appareil, enclencher le dispositif de coupure

d’alimentation ou débrancher la fiche

d’alimentation.

ATTENTION

Par mesure de sécurité, ne raccordez pas le

connecteur pour le câblage de périphériques

pouvant avoir une tension excessive au port

AVERTISSEMENT

1. Utilisez un cordon d’alimentation (câble secteur

à 2 fils)/fiche femelle/fiche mâle conformes à la

réglementation de sécurité locale/régionale

applicable.

2. Utilisez un cordon d’alimentation (câble secteur

à 2 fils)/fiche femelle/fiche mâle avec des

caractéristiques nominales (tension, ampérage)

appropriées.

Pour toute question sur l’utilisation du cordon

d’alimentation/fiche femelle/fiche mâle ci-dessus,

consultez un technicien du service après-vente

qualifié.

IMPORTANT

La plaque signalétique se situe à l’endroit suivant

sur l’appareil.

Côté

ATTENTION

– Il y a danger d’explosion s’il y a remplacement

incorrect de la batterie. Remplacer uniquement

avec une batterie du même type ou d’un type

équivalent recommandé par le constructeur.

– Lors de la mise au rebut de la batterie ou du

produit, vous devez respecter la loi de la région

ou du pays concerné. Ne mettez pas la batterie

ou le produit au rebut dans un feu ou un four

chaud, ou n’écrasez pas mécaniquement la

batterie et ne la coupez pas. Elle risque

d’exploser ou de provoquer un incendie. Ne

soumettez pas la batterie à une pression d’air

extrêmement basse qui pourrait entraîner une

explosion ou une fuite de liquide ou de gaz

inflammable.

– Ne placez pas la batterie dans un endroit à

température élevée, tel qu’à la lumière directe

du soleil ou à proximité d’un feu. Elle risque de

prendre feu, d’exploser ou de provoquer un

incendie. Ne plongez pas et ne mouillez pas la

batterie dans de l’eau douce ou de l’eau de mer.

Cela risque de provoquer une électrocution.

ATTENTION

La taille et le nombre de piles suivants sont requis

pour la télécommande.

Taille : AA (R6)

Nombre de pile(s) : deux pièces

Pour éviter tout risque d’explosion, utilisez

uniquement le type de pile suivant.

Piles au manganèse

Le symbole avertit l’utilisateur de la présence

d’importantes instructions concernant le

fonctionnement et la maintenance (entretien)

dans la documentation qui accompagne l’appareil.

AVERTISSEMENT

Ne regardez pas dans l’objectif pendant son

utilisation.

ATTENTION

L’emploi de commandes ou ajustements ou

l’exécution de procédures autres que celles

spécifiées ici peut provoquer une exposition

dangereuse au rayonnement.

IEC 60825-1:2014

PRODUIT LASER DE CLASSE 1

Comme pour n’importe quelle

source de lumière vive, ne

regardez pas fixement le

faisceau, RG2 IEC 62471-5:2015.

Français

FR 20

ATTENTION

L’emploi d’instruments optiques avec ce produit

augmentera les risques pour les yeux.

Informations sur l’emplacement des étiquettes

Spécifications de la source lumineuse

Diodes laser 5,2 W × 24

Longueur d’onde : 450 - 460 nm

Angle de divergence du faisceau par rapport à

l’objectif de cet appareil

Zoom maximum : α = 39,9 °

Zoom minimum : α = 25,5 °

Ne placez aucun objet devant l’objectif pour éviter

de bloquer la lumière durant la projection. La

chaleur provenant de la lumière risque

d’endommager l’objet.

Pour les clients en Europe

Fabricant : Sony Corporation, 1-7-1 Konan Minato-

ku Tokyo, 108-0075 Japon

Pour toute question relative à la conformité des

produits dans l’UE : Sony Belgium, bijkantoor van

Sony Europe B.V., Da Vincilaan 7-D1, 1930

Zaventem, Belgique

ÉTIQUETTE DE CLASSE 1

PICTOGRAMME ATTENTION RG2

Port d’émission laser

La page charge ...

Sony VPL-XW7000 Mode d'emploi

Sony VPL-XW7000 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents