STIHL BGA 45 Manuel utilisateur

{

STIHL BGA 45

Instruction Manual

Notice d’emploi

G Instruction Manual

1 - 27

F Notice d’emploi

28 - 58

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-719-8221-A. VA2.D18.

0000007656_005_GB

0458-719-8221-A

English

1

{

with electronic systems.

Contents

1 Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

2 Guide to Using this Manual

. . . . . . . . . . . . . . . . . . . . . . . . . .

2

2.1 Signal Words

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

2.2 Symbols in Text

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

3 Main Parts

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

3.1 Blower and Charger

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

4 Safety Symbols on the Products

. . . . . . . . . . . . . . . . . . . . .

4

4.1 Blower and Charger

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

5 IMPORTANT SAFETY INSTRUCTIONS

. . . . . . . . . . . . .

5

5.1 Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

5.2 Intended Use

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

5.3 Operator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

5.4 Personal Protective Equipment

. . . . . . . . . . . . . . . . . . . . . .

6

5.5 Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

5.6 Integrated Battery

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7

5.7 Using the Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

6 Charger Safety

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12

6.1 Warnings and Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . .

12

7 Maintenance, Repair and Storage

. . . . . . . . . . . . . . . . . .

14

7.1 Warnings and Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . .

14

8 General Warnings and Instructions

. . . . . . . . . . . . . . . . .

14

8.1 General Safety Warnings and Instructions for

Battery-Powered Products

. . . . . . . . . . . . . . . . . . . . . . . . . .

14

9 Before Starting Work

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

9.1 Preparing the Blower for Operation

. . . . . . . . . . . . . . . . .

15

10 Charging the Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

10.1 Charging

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

11 LED Diagnostics

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16

11.1 Blower Status

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16

11.2 Charge Status

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16

12 Assembling the Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

12.1 Mounting the Blower Tube and Nozzle

. . . . . . . . . . . . .

17

13 Inserting and Removing the Activation Key

. . . . . . . . .

17

13.1 Inserting the Activation Key

. . . . . . . . . . . . . . . . . . . . . . . .

17

13.2 Removing the Activation Key

. . . . . . . . . . . . . . . . . . . . . . .

18

14 Switching the Blower On and Off

. . . . . . . . . . . . . . . . . . .

18

14.1 Switching On

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18

14.2 Switching Off

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

15 Checking the Controls

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

15.1 Testing the Controls

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

16 During Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

16.1 Using the Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

17 After Finishing Work

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

17.1 Preparing for Transportation or Storage

. . . . . . . . . . . .

20

18 Transporting the Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

18.1 Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

19 Storing the Blower and Charger

. . . . . . . . . . . . . . . . . . . .

21

19.1 Blower

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

19.2 Charger

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

20 Cleaning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

20.1 Cleaning the Blower and Charger

. . . . . . . . . . . . . . . . . .

22

21 Inspection and Maintenance

. . . . . . . . . . . . . . . . . . . . . . .

22

21.1 Inspecting and Maintaining the Blower

. . . . . . . . . . . . .

22

22 Troubleshooting Guide

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24

22.1 Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24

23 Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25

23.1 STIHL BGA 45

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25

23.2 STIHL LK 45

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25

23.3 Symbols on the Blower and Charger

. . . . . . . . . . . . . . .

25

23.4 Engineering Improvements

. . . . . . . . . . . . . . . . . . . . . . . . .

26

23.5 EMC Compliance Statement for Power Tool and

Charger

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

24 Replacement Parts and Equipment

. . . . . . . . . . . . . . . . .

26

24.1 Genuine STIHL Replacement Parts

. . . . . . . . . . . . . . . .

26

0458-719-8221-A

2

English

1 Introduction

Thank you for your purchase. The information contained in

this manual will help you receive maximum performance and

satisfaction from your blower and, if followed, reduce the risk

of injury from its use.

SAVE THIS MANUAL!

Have your authorized STIHL servicing dealer show you how

to operate your power tool.

Do not lend or rent the blower without this instruction

manual. Allow only persons who fully understand the

information in this manual to operate the blower.

For further information, or if you do not understand any of

the instructions in this manual, please go to

www.stihlusa.com (for Canada: www.stihl.ca) or contact

your authorized STIHL servicing dealer.

2.1 Signal Words

This manual contains safety information that requires your

special attention. Such information is introduced with the

following symbols and signal words:

DANGER

Indicates a hazardous situation that, if not avoided, will

result in death or serious injury.

25 Disposal

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26

25.1 Disposal of the Blower and Charger

. . . . . . . . . . . . . . . .

26

1 Introduction

Because a blower is a high-speed battery-

powered tool, special safety precautions must

be observed to reduce the risk of personal injury.

Read this instruction manual thoroughly before

use and periodically thereafter. Follow all safety

precautions. Careless or improper use of the

blower can cause serious or fatal injury.

2 Guide to Using this Manual

0458-719-8221-A

3

English

3 Main Parts

WARNING

Indicates a hazardous situation that, if not avoided, could

result in death or serious injury.

NOTICE

Indicates a risk of property damage, including damage to the

machine or its individual components.

2.2 Symbols in Text

The following symbol is included to assist you with the use

of the manual:

3.1 Blower and Charger

The blower is powered by an integrated lithium ion battery

that cannot be removed from the power tool.

1 Retaining Latch

Locks/unlocks the trigger switch.

2 Trigger Switch

Switches the motor on and off.

3 Trigger Switch Lockout

Must be depressed while the retaining latch is unlocked

to allow activation of the trigger switch.

4 Blower LEDs

Indicate the blower's state of charge and display error

messages regarding potential malfunctions in the power

tool or its integrated battery.

Refers to a designated chapter or sub-chapter in this

instruction manual.

3Main Parts

9

10

2

1

3

15

0000-GXX-2265-A1

6

4

5

7

8

11

12

13

14

16

17

#

0458-719-8221-A

4

English

4 Safety Symbols on the Products

5 Push Button

Activates the blower's LEDs.

6 Intake Screen

Fits over the air intake opening and reduces risk of direct

contact with the blower fan.

7 Charging Socket

Socket for connecting the charger to the blower.

8Activation Key

Enables the flow of electrical power from the integrated

battery to the motor.

9 Activation Key Socket

Socket for connecting the activation key to the blower.

10 Housing

Contains the integrated battery.

11 Control Handle

The blower's handle.

12 Blower Tube

Directs the airstream.

13 Nozzle

Directs and concentrates the airstream.

14 Connector

Connects the charger to the blower's charging socket.

15 Power Supply Cord

Supplies electrical charging current when the charger is

plugged into a wall outlet.

16 Plug

Connects the charger to a wall outlet.

17 Charger (Power Supply)

Power supply for charging the blower.

# Rating Plate

Contains electrical information and the product's serial

number.

4.1 Blower and Charger

The following safety symbols are found on the blower and/or

charger:

4 Safety Symbols on the Products

To reduce the risk of injury, follow the specified

safety precautions.

Read and follow all safety precautions in the

instruction manual. Improper use can lead to

serious or fatal personal injury or property

damage.

To reduce the risk of eye injury, always wear

proper eye protection, @ 5.4.

To reduce the risk of personal injury, keep hair

and loose-fitting clothing away from the air

intake, @ 5.4.

To reduce the risk of injury or property damage

from unintended activation, remove the

activation key any time the blower is not in use,

@ 7.

To reduce the risk of personal injury or property

damage from a short circuit, fire or explosion,

keep the blower dry. Protect it from rain, water,

liquids and damp conditions. Never immerse the

blower in water or other liquids, @ 5.5.

To reduce the risk of personal injury from

high velocity air flow and blown objects,

keep bystanders at least 16 ft. (5 m) away,

@ 5.7.4.

5m (16 ft)

0458-719-8221-A

5

English

5 IMPORTANT SAFETY INSTRUCTIONS

5.1 Introduction

When using an electric blower, basic precautions should

always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THE

BLOWER!

SAVE THESE INSTRUCTIONS

WARNING

￭ To reduce the risk of fire, explosion, electric shock or other

personal injury, read and follow the important safety

instructions in this chapter. Additional important warnings

and instructions are provided in subsequent chapters of

this manual.

5.2 Intended Use

WARNING

￭ This blower is designed for blowing leaves, grass, and

similar lightweight material from yards, gardens,

sidewalks, driveways, decks, patios and comparable

surfaces in the manner and in the conditions described in

this manual. Use of the blower for operations different

than intended could result in serious injury or death.

► Blow leaves, grass, and similar lightweight material

only.

► Do not use it for any other purposes.

￭ Improper use could result in personal injury or property

damage, including damage to the blower.

► Use the blower and charger only as described in this

manual.

► Never attempt to modify or override the blower's

controls or safety devices in any way.

► Never use a blower that has been modified or altered

from its original design.

￭ The LK45 charger (power supply) is designed for

charging STIHL BGA 45, FSA 45 and HSA 45 power tools

only.

5.3 Operator

WARNING

￭ Working with the blower can be strenuous. The operator

must be in good physical condition and mental health. To

reduce the risk of personal injury from fatigue and loss of

control:

► Check with your doctor before using the blower if you

have any health condition that may be aggravated by

strenuous work.

► Do not operate the blower while under the influence of

any substance (drug, alcohol or medication, etc.) that

might impair vision, balance, dexterity or judgment.

► Be alert. Do not operate the blower when you are tired.

Take a break if you become tired.

To reduce the risk of personal injury or property

damage from fire, explosion or burns, including

chemical burns, do not disassemble the

blower's housing. Never crush, drop, damage or

heat the blower above 212°F (100°C). Never

expose it to fire or incinerate, @ 5.5.

To reduce the risk of personal injury or property

damage from fire, use and store the blower only

within an ambient temperature range of 32°F to

122°F (0°C to 50°C), @ 5.6.

To reduce the risk of personal injury or property

damage from fire or electric shock, keep the

charger dry. Protect them from rain, water,

liquids and damp conditions. For indoor use

only, @ 6.

5 IMPORTANT SAFETY

INSTRUCTIONS

0458-719-8221-A

6

English

5 IMPORTANT SAFETY INSTRUCTIONS

► Do not permit minors to use the blower.

￭ According to STIHL's current knowledge, the electric

motor of this blower should not interfere with a

pacemaker.

► However, persons with a pacemaker or other implanted

medical device should consult their physician and

pacemaker manufacturer before operating this blower.

5.4 Personal Protective Equipment

WARNING

￭ To reduce the risk of personal injury:

► Always wear proper clothing and protective apparel,

including proper eye protection.

￭ Loss of control and severe injuries may result if hair,

clothing or apparel are drawn into the air intake or

otherwise become entangled in the components of the

blower. To reduce the risk of severe personal injury:

► Wear a long-sleeve shirt or jacket.

￭ To reduce the risk of eye injury:

￭ Good footing is very important. To help maintain a secure

footing and reduce the risk of injury while working:

￭ To help reduce the risk of personal injury caused by static

discharge and/or loss of control during operation:

5.5 Blower

WARNING

￭ To reduce the risk of electric shock:

￭ This battery-powered blower is intended only for light-duty

garden and landscape maintenance around the home.

Use for other purposes may increase the risk of personal

injury and property damage.

► Read and follow the operating instructions in this

manual for approved applications, @ 16.

► Do not allow to be used as a toy. Close attention is

necessary when used by or near children.

￭ To reduce the risk of personal injury to the operator and

bystanders:

► Wear sturdy and snug-fitting clothing that

also allows complete freedom of

movement.

► Wear overalls or long pants made of

heavy material to help protect your legs.

Do not wear shorts.

► Avoid loose-fitting jackets, scarves,

neckties, flared or cuffed pants, jewelry

and any other apparel that could be

drawn into the air intake.

► Secure hair above shoulder level before

starting work.

► Always wear goggles or close-fitting

protective glasses with adequate side

protection that are impact-rated and

marked as complying with CSAZ94.

► Wear substantial footwear with non-slip

soles. Do not wear sandals, flip-flops,

open-toed or similar footwear.

► STIHL recommends wearing heavy-duty

non-slip work gloves made of leather or

another wear-resistant material when

handling the blower.

► Do not expose the blower to rain, water

or excessive moisture.

► Store the blower indoors.

► Never immerse the blower in water or

other liquids.

► Always release the trigger switch and

remove the activation key before

assembling, transporting, adjusting,

inspecting, cleaning, servicing,

maintaining or storing the blower and

any other time it is not in use.

0458-719-8221-A

7

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ Although certain unauthorized attachments may fit STIHL

blowers, their use may be extremely dangerous. Only

attachments supplied by STIHL or expressly approved by

STIHL for use with this specific model are authorized.

► Use only attachments supplied or expressly approved

by STIHL.

► Never modify this blower in any way.

► Never attempt to modify or override the blower's

controls or safety devices in any way.

► Never use a blower that has been modified or altered

from its original design.

► Do not put any object into the openings of the blower.

► Do not use the blower with any openings blocked.

► Keep the blower free of dust, lint, hair and anything that

might reduce air flow.

￭ If the blower is dropped or subjected to similar heavy

impacts:

► Check that it is undamaged, in good condition and

functioning properly before continuing work.

► Check that the controls and safety devices are working

properly.

► Check the LEDs for error messages, @ 11.1.

► Never work with a damaged or malfunctioning blower.

► Never use or charge a blower with a housing that is

cracked, deformed, excessively hot, leaking battery

fluid or otherwise damaged. These could be signs that

the battery inside the blower is damaged, increasing the

risk of personal injury and property damage from short

circuit, fire or explosion. In case of doubt, have the

blower checked by your authorized STIHL servicing

dealer.

￭ If the blower is damaged, not working properly, has been

left outdoors, exposed to rain or damp conditions or

dropped into water or other liquid, its components,

including its integrated battery, may no longer function

properly and safety devices may be inoperative. To

reduce the risk of personal injury and property damage:

► Take the blower to your authorized STIHL servicing

dealer to be checked before further operation.

￭ Genuine STIHL replacement parts are specifically

designed to match your blower and meet safety and

performance requirements. Use of parts that are not

authorized or approved by STIHL may cause serious or

fatal injury or property damage.

► STIHL recommends that only identical STIHL

replacement parts be used.

5.6 Integrated Battery

WARNING

￭ Use of an unauthorized charging device can damage the

lithium ion battery inside the blower and result in fire,

explosion and personal injury and property damage.

► Charge the blower only with a genuine STIHLLK45

charger (power supply).

￭ The blower's integrated battery contains safety features

and devices which, if damaged, may allow it to generate

heat, rupture, leak, ignite or explode.

► Be alert for signs that the battery may be damaged:

never use or charge a blower with a housing that is

cracked, deformed, excessively hot, leaking battery

fluid or otherwise damaged.

► Do not incinerate the blower even if it is severely

damaged. The integrated battery can explode in a fire.

► Never attempt to remove the battery or open or

disassemble the blower's housing for any reason.

► Never subject the blower to heavy impacts or attempt to

crush, drop or otherwise damage it.

0458-719-8221-A

8

English

5 IMPORTANT SAFETY INSTRUCTIONS

► Never expose the blower to microwaves or high

pressures.

► Never insert foreign objects into the blower's charging

socket, activation key socket or other openings.

￭ High temperatures may cause the blower's integrated

battery to generate heat, rupture, leak, ignite or explode,

resulting in severe or fatal personal injury and property

damage. Exposure to temperatures outside the

recommended temperature range may also damage the

battery.

￭ To reduce the risk of personal injury and property damage

in the event the blower emits smoke, an unusual smell or

feels unusually hot while using, charging or storing:

► Immediately discontinue using or charging the blower

and prepare to contact the authorities in the event of fire

or explosion.

￭ To reduce the risk of electric shock:

► Never bridge the electrical contacts of the activation key

socket with wires or other metallic objects (e.g., paper

clips, nails, coins, keys).

► Store the blower indoors in a dry room.

► Never store the blower in damp or corrosive

environments or in conditions that could lead to

corrosion of its metal components or battery.

► Protect the blower from exposure to corrosive agents

such as garden chemicals and de-icing salts, which may

damage its battery and increase the risk of short circuit,

fire and explosion.

► Do not attempt to repair, open or disassemble the

blower. There are no user-serviceable parts inside.

￭ If the integrated battery is damaged, battery fluid can leak

out of the blower. Leaking battery fluid can cause skin and

eye irritation or chemical burns.

► Avoid contact with skin and eyes.

► Use an inert absorbent such as sand on spilled liquids.

► In the event of accidental contact, immediately rinse the

contact area thoroughly with mild soap and water.

► If fluid gets into your eye(s): Do not rub. Rinse water

over the open eye(s) for at least 15 minutes and seek

medical attention.

￭ A battery fire can be dangerous. To reduce the risk of

severe personal injury and property damage in the event

of fire:

► Evacuate the area. Fire can spread rapidly. Stay clear

of any vapors generated and maintain a safe distance.

► Contact the fire department.

► Although water can be used to put out a battery fire, use

of a multi-purpose dry chemical fire extinguisher is

preferable.

► Consult the fire department regarding proper disposal of

the burned battery.

► Never heat the blower above 212°F

(100°C) or place it on or near fires,

stoves or other high-temperature

locations.

► Use and store the blower only within an

ambient temperature range of 32°F to

122°F (0°C to 50°C).

► Never store the blower in direct sunlight

or inside a vehicle in hot weather.

► Keep the blower dry. Protect it from rain

and ensure that the blower and its

battery are never exposed to water,

liquids or damp conditions.

► Never immerse the blower in water or

other liquids.

0458-719-8221-A

9

English

5 IMPORTANT SAFETY INSTRUCTIONS

5.7 Using the Blower

5.7.1 Before Operation

WARNING

￭ Misuse or unauthorized use may result in personal injury

and property damage.

► Use the blower only as described in this instruction

manual.

￭ Using a blower that is modified, damaged, improperly

adjusted or maintained, or not completely and securely

assembled can lead to a malfunction and increase the risk

of serious personal injury.

► Never operate a blower that is modified, damaged,

improperly maintained or not completely and securely

assembled.

► Always check your blower for proper condition and

operation before starting work, particularly the retaining

latch, trigger switch lockout and trigger switch.

► Ensure that the retaining latch, trigger switch lockout

and trigger switch move freely and always spring back

to the stop position when released. The trigger switch

must not engage until the retaining latch is unlocked and

the trigger switch lockout is depressed.

► Never attempt to modify or override the controls or

safety devices in any way.

► If your blower or any part is damaged or does not

function properly, take it to your authorized STIHL

servicing dealer. Do not use the blower until the problem

has been corrected.

￭ Before inserting the activation key:

► Check the electrical contacts of the activation key and

activation key socket for corrosion or other foreign

matter. Keep clean.

► Never insert a damaged, deformed or corroded

activation key.

► Read and follow the instructions on switching on the

blower, @ 14.1.

￭ To help reduce the risk of serious personal injury from

unintentional starting:

► Be sure the retaining latch is in the locked position and

the trigger switch is in the off position before inserting

the activation key.

► Never carry the blower with your finger on the trigger

switch.

► Release the trigger switch before removing the

activation key.

► Never leave the blower unattended when the activation

key is inserted.

► Never store the activation key in the blower.

5.7.2 Holding and Controlling the Blower

► Remove the activation key before

assembling, transporting, adjusting,

inspecting, cleaning, servicing,

maintaining or storing the blower and

any other time it is not in use.

0000-GXX-2266-A0

0458-719-8221-A

10

English

5 IMPORTANT SAFETY INSTRUCTIONS

WARNING

￭ To maintain a firm grip and properly control your blower:

► Keep the handle clean and dry at all times. Keep it free

of moisture, pitch, oil, grease and resin.

￭ To reduce the risk of serious or fatal injuries to the

operator or bystanders from loss of control:

► Always hold the blower firmly with one hand when you

are working.

► Wrap your fingers tightly around the handle, keeping the

handle cradled between your thumb and forefinger (see

illustration above).

￭ To reduce the risk of serious or fatal injuries to the

operator or bystanders from loss of control, keep proper

footing and balance at all times:

► Never work on a ladder, roof, in a tree or while standing

on any other insecure support.

► Take special care in overgrown or wet terrain and

always watch for hidden obstacles such as tree stumps,

roots, rocks, holes and ditches to avoid stumbling or

falling.

► Be extremely cautious when working on slopes or

uneven ground.

► Use extra care when cleaning on stairs.

► For better footing, always clear away fallen branches,

scrub, cuttings and other material, objects or vegetation

that can increase the danger of slipping, tripping or

falling.

► Never operate the blower above shoulder height.

► Do not overreach. Keep proper footing and balance at

all times.

5.7.3 Working Conditions

WARNING

￭ Operate your blower only under good visibility during

favorable daylight conditions.

► Postpone the work if the weather is windy, foggy, rainy

or inclement.

￭ Your blower is a one-person machine.

► Bystanders, especially children, and animals should not

be allowed in the area where it is in use.

► Switch off the blower immediately if you are

approached.

￭ To reduce the risk of injury to bystanders and

unauthorized users:

► Never leave the blower unattended when the activation

key is inserted.

► Switch off the blower and remove the activation key

during work breaks and any other time the blower is not

in use.

￭ Operating the blower in certain dry, dusty conditions may

cause static electricity to build up in the blower tube,

nozzle and housing. This static electricity may discharge

suddenly with a spark. To reduce the risk of personal

injury following static discharge:

► Wear heavy-duty work gloves made of leather or

another wear-resistant material.

► Never operate the blower in a location where

combustible gases, liquids, vapors, dusts or other

combustible materials and substances are present.

0458-719-8221-A

11

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ Sparks generated from operation of the blower may be

capable of igniting combustible gases, liquids, vapors,

dusts or other combustible materials and substances. To

reduce the risk of fire and explosion:

► Never operate the blower in a location where

combustible gases, liquids, vapors, dusts or other

combustible materials and substances are present.

► Read and follow recommendations issued by

government authorities (e.g., CCOHS) for identifying

and avoiding the hazards of combustible gases, liquids,

vapors, dusts or other combustible materials and

substances.

￭ Use of this blower can generate dust and other

substances containing chemicals known to cause

respiratory problems, cancer, birth defects and other

reproductive harm.

► Consult governmental agencies such as ECCC,

CCOHS and PHAC and other authoritative sources on

hazardous materials if you are unfamiliar with the risks

associated with the particular substances with which

you are working.

￭ Inhalation of certain dusts, especially organic dusts such

as mold or pollen, can cause susceptible persons to have

an allergic or asthmatic reaction. Substantial or repeated

inhalation of dust or other airborne contaminants,

especially those with a smaller particle size, may cause

respiratory or other illnesses.

► Control dust at the source where possible.

► To the extent possible, operate the blower so that the

wind or operating process directs any dust, mist or other

particulate matter raised by the blower away from the

operator.

► When respirable dust or other particulate matter cannot

be kept at or near background levels, always wear a

respirator that is approved by PHAC and rated for

worksite-specific conditions. Follow the

recommendations of governmental authorities (e.g.,

CCOHS/PHAC) and occupational and trade

associations.

￭ If the surrounding ground is coated with a chemical

substance, such as pesticide or herbicide:

► Read and follow the instructions and warnings that

accompanied the substance coating the vegetation or

surrounding ground.

5.7.4 Operating Instructions

WARNING

￭ In the event of an emergency:

► Switch off the motor immediately and remove the

activation key.

￭ The blower fan between the air intake and output opening

rotates whenever the motor is running. To reduce the risk

of injury from contact with the blower fan:

► Never operate the blower with a missing, cracked or

worn intake screen or housing.

► Never operate the blower without a properly mounted

blower tube and nozzle.

► Keep hair, loose clothing, fingers and all parts of the

body away from openings and moving parts of the

blower.

￭ The air flow from the blower can propel small objects at

high speed. To reduce the risk of eye or other serious

personal injuries to bystanders from blown objects:

► Keep bystanders and pets at least 16ft. (5m) away

when the blower is running.

► Never direct the air flow toward bystanders or pets.

► Do not allow the blower to be used as a toy.

► Switch off the blower immediately if you are

approached.

0458-719-8221-A

12

English

6 Charger Safety

￭ A missing, cracked or worn intake screen or housing may

result in an increased risk of injury from thrown objects.

► Never operate a blower that has a missing, cracked or

worn intake screen or housing.

￭ Inserting any foreign object into the air intake or nozzle

may result in property damage, including damage to the

blower itself, and serious injury to the operator or

bystanders as a result of the object or broken parts being

blown at high speed.

► Never insert any objects into the nozzle or air intake of

the blower.

► Immediately switch off the blower if it starts to vibrate

abnormally.

￭ Using the blower to spread herbicides, pesticides,

fertilizers or other chemical substances can be dangerous

and may cause serious or fatal injury to persons and

damage to the environment.

► Never use the blower to disperse or spread chemicals

of any kind.

6.1 Warnings and Instructions

WARNING

￭ To reduce the risk of fire, electric shock and other

personal injury or property damage:

► Read and follow all cautionary markings on the charger

and blower and all instructions in this manual before

using the charger.

► Use the STIHLLK45 charger (power supply) only for

charging STIHLBGA45, FSA45 and HSA45 power

tools. Using the STIHLLK45 for other purposes is

prohibited and may lead to fire, explosion or electric

shock, resulting in serious or fatal personal injury and

property damage.

► Do not handle the charger, including power supply cord

and plug, with wet hands.

► Never use a damaged or improperly functioning

charger.

► Never use or charge a blower with a housing that is

cracked, deformed, excessively hot, leaking battery

fluid or otherwise damaged. These could be signs that

the battery inside the blower is damaged, increasing the

risk of personal injury and property damage from short

circuit, fire or explosion.

► Operate the charger only indoors, in dry rooms and

within an ambient temperature range of 32°F to 104°F

(0°C to 40°C).

► Keep the charger out of the reach of children.

► Always plug the charger into a properly installed wall

outlet matching the voltage and electrical frequency

stated on the charger.

► Never use power strips to operate multiple chargers or

other devices from the same outlet or on the same

circuit.

► Do not operate a charger that has received a sharp or

heavy blow, has been dropped or is otherwise damaged

or not functioning properly in any way.

► Do not attempt to repair, open or disassemble the

charger. There are no user-serviceable parts inside.

6 Charger Safety

► For indoor use only.

► Keep the charger dry. Protect it from

rain, water, liquids and damp conditions.

Never charge a wet blower or use a wet

charger.

0458-719-8221-A

13

English

6 Charger Safety

￭ To reduce the risk of electric shock or fire from a short

circuit:

► Make sure the blower and charger are completely dry

before starting the charging process.

￭ The charger heats up during the charging process. To

reduce the risk of fire:

► Do not operate on a combustible surface (e.g., paper,

cardboard, textiles) or in a combustible environment.

► Allow the charger to cool down normally. Do not cover it.

￭ Chargers can produce sparks which may ignite

combustible gases, liquids, vapors, dusts or other

combustible materials. To reduce the risk of fire and

explosion:

► Do not operate in a location where combustible gases,

liquids, vapors, dusts or other combustible materials are

present.

￭ Using a damaged power supply cord or plug may result in

fire, electric shock and other personal injury or property

damage. To reduce these risks:

► Replace the charger if the power supply cord becomes

damaged. The power supply cord cannot be repaired or

replaced.

► Unplug the charger from the wall outlet when not in use.

► Never jerk the power supply cord to disconnect it from

the wall outlet. To unplug, grasp the plug, not the power

supply cord.

► Do not use the power supply cord for any other purpose,

e.g., for carrying or hanging up the charger.

► Make sure the power supply cord is located or marked

so that it will not be stepped on, tripped over, come in

contact with sharp objects or moving parts, or otherwise

be subjected to damage or stress.

￭ An extension cord should not be used unless absolutely

necessary. Overloading an extension cord can result in

overheating and fire. If an extension cord must be used:

► Use only a properly wired 16 gauge (AWG16) or

heavier gauge extension cord.

► Never connect more than one charger or other device to

an extension cord.

► Never use an extension cord with a wattage rating lower

than the wattage on your charger's rating plate.

► Never use an extension cord if the blades on its plug are

different from the blades on the charger plug in number,

size or shape.

► Do not link (chain) extension cords.

￭ In case of fire, or if the charger or blower it is charging

emits smoke, an unusual smell, feels hot or appears

abnormal in any other way:

► Immediately disconnect the charger from the outlet.

Contact the authorities in the event of fire or explosion.

► Have the charger and blower inspected and repaired by

an authorized STIHL servicing dealer before use.

￭ Operation of the blower is disabled during the charging

process to reduce the risk of electric shock.

► Do not attempt to operate the blower during the

charging process or any time it is connected to the

LK45.

► Check the charger's power supply cord

and plug regularly for damage. If

damaged, immediately disconnect the

plug from the wall outlet.

0458-719-8221-A

14

English

7 Maintenance, Repair and Storage

7.1 Warnings and Instructions

WARNING

￭ There are no user-authorized repairs for the blower or

charger. To reduce the risk of fire, electric shock or other

personal injury and property damage:

► Users may carry out only the cleaning and maintenance

operations described in this manual. Users must not

attempt any other cleaning, maintenance or repair.

► Strictly follow the cleaning and maintenance

instructions in the appropriate sections of this

instruction manual.

► STIHL recommends that all repair work be performed by

authorized STIHL servicing dealers.

￭ Unintentional starting may result in personal injury or

property damage.

￭ Use of parts that are not authorized or approved by STIHL

may cause serious or fatal injury or property damage.

► STIHL recommends that only identical authorized

STIHL replacement parts be used for repair or

maintenance.

￭ To reduce the risk of electric shock:

► Unplug the charger from the wall outlet before

inspecting or cleaning the charger.

► Regularly check the electrical contacts of the charger

and ensure that the insulation of the power cord and

plug are in good condition and show no signs of aging

(brittleness), wear or damage.

► Replace the charger if the power supply cord becomes

worn or damaged. The power supply cord cannot be

repaired or replaced.

￭ To reduce the risk of short circuit and fire:

► Keep the charging socket and power supply cord

connector free of foreign matter. Clean as necessary,

@ 20.

￭ Improper storage can result in unauthorized use, damage

to the blower and charger and an increased risk of fire,

electric shock and other personal injury or property

damage.

► Remove the activation key from the blower before

storing. Store the activation key away from the blower in

a safe place that is inaccessible to children and other

unauthorized users.

► Never store the blower with the activation key inserted.

► Before storing, always unplug the charger from the wall

outlet.

► Store the blower and charger indoors in a dry, secure

place that cannot be accessed by children or other

unauthorized users.

► Store the blower only within an ambient temperature

range of 32 °F to 122 °F (0 °C to 50 °C).

8.1 General Safety Warnings and Instructions for

Battery-Powered Products

This section contains the general safety warnings and

instructions for battery-powered products contained in

UL2595 / CSAC22.2No.0.23.

WARNING

￭ Read all safety warnings and instructions.

￭ Failure to follow the warnings and instructions may result

in electric shock, fire, explosion and/or serious injury or

property damage.

￭ Prevent unintentional starting. Ensure the trigger switch is

in the off-position before inserting the activation key,

picking up or carrying the blower. Carrying the blower with

7 Maintenance, Repair and Storage

► Remove the activation key before

inspecting the blower or carrying out any

cleaning, maintenance or repair work,

before storing, and any other time the

blower is not in use.

8 General Warnings and Instructions

0458-719-8221-A

15

English

9 Before Starting Work

your finger on the trigger switch or inserting the activation

key with the trigger switch engaged increases the

likelihood of unintended starting and possible accidents.

￭ Remove the activation key from the blower before making

any adjustments, changing accessories, or storing. Such

preventive safety measures reduce the risk of starting the

blower accidentally.

￭ Recharge only with the charger specified by STIHL. A

charger that is suitable for one type of power tool may

create a risk of fire when used with another power tool.

￭ Use the blower only with the integrated battery. Use of any

other battery may create a risk of fire or explosion and

personal injury or property damage.

￭ When the power tool is not in use, make sure that paper

clips, coins, keys, nails and other similar metal objects are

not stored near the blower's charging socket, activation

key socket or other openings. Short circuiting the blower's

battery or charging system may cause burns or a fire or

explosion.

￭ Under abusive conditions, liquid may be ejected from the

battery; avoid contact. If contact accidentally occurs, flush

with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation, chemical burns or respiratory illness from

inhalation.

￭ Do not use a blower that is damaged or modified. A

damaged or modified blower or integrated battery may

exhibit unpredictable behavior resulting in fire, explosion

and risk of injury or property damage.

￭ Do not expose the blower or its integrated battery to fire or

excessive temperature. Exposure to fire or temperature

above 212°F (100°C) may cause fire and explosion.

￭ Follow all charging instructions and do not charge the

integrated battery outside of the ambient temperature

range specified. Charging improperly or outside the

specified range may damage the battery and increase the

risk of fire.

￭ Have servicing performed by a qualified repair person

using only authorized replacement parts. This will help

maintain the safety and performance of the product.

￭ Do not modify or attempt to repair the blower or the

integrated battery. Follow the instructions for use and

care.

9.1 Preparing the Blower for Operation

Before starting work:

► Fully charge the blower, @ 10.

► Mount the blower tube and nozzle, @ 12.1.

► Check the controls for proper function and condition,

@ 15.

10.1 Charging

WARNING

Read and follow the blower and charger safety precautions

and instructions in this manual, @ 5.5 and @ 6. Be alert for

signs that the integrated battery may be damaged. To

reduce the risk of fire and explosion, never use or charge a

blower with a housing that is cracked, deformed, excessively

hot, leaking battery fluid or otherwise damaged, @ 5.6.

9 Before Starting Work

10 Charging the Blower

0458-719-8221-A

16

English

11 LED Diagnostics

WARNING

Since the blower and charger heat up during the charging

process, do not charge the blower on a combustible surface

or in a location where combustible gases, liquids, vapors,

dusts or other combustible materials or substances are

present, @ 6.

To charge the blower:

► Remove the activation key, @ 13.2.

► Insert the charger plug into a properly installed wall

outlet(1) with the same voltage and electrical frequency

stated on the charger's rating plate(2).

► Push the connector(4) into the blower's charging

socket(5) until it stops.

The LEDs on the blower(6) glow green during charging

and show the state of charge.

When the LEDs on the blower go out, the charging

process is complete and the charger will shut itself off.

► Remove the charger from the blower and disconnect the

charger plug from the wall outlet when charging is

complete.

A blower is not fully charged when it ships from the factory.

STIHL recommends that you fully charge the blower before

using it the first time.

Operate the charger only indoors, in dry rooms and within an

ambient temperature range of 32°F to 104°F (0°C to

40°C).

The blower heats up during operation. The charging process

begins only after the blower and its integrated battery have

cooled down sufficiently.

Charging time depends on a number of factors, including the

condition of the integrated battery and the ambient

temperature. For a complete list of approximate charging

times, see www.stihl.com/charging-times.

Operation of the blower is disabled during charging and any

time the blower is connected to the charger.

11.1 Blower Status

LEDs on the blower show the status of the power tool and its

integrated battery.

If three LEDs glow red continuously: the integrated battery

is either too hot or too cold. Allow the blower to warm up or

cool down gradually at an ambient temperature of about

50°F to 68°F (10°C to 20°C).

If three LEDs flash red when you activate the trigger switch:

the blower has an electrical malfunction. Do not operate or

charge the blower. Have it checked by an authorized STIHL

servicing dealer before use or storage.

For troubleshooting information, @ 22.

11.2 Charge Status

The LEDs also show the blower's state of charge.

4

0000-GXX-2267-A0

6

5

3

2

1

11 LED Diagnostics

0458-719-8221-A

17

English

12 Assembling the Blower

To determine the blower's state of charge:

► Press the push button(1) on the blower.

The LEDs on the blower will glow or flash green for about

5seconds and indicate the state of charge (see

illustration).

For example:

If four green LEDs glow continuously: full charge.

If one green LED is flashing: less than 20% charge.

12.1 Mounting the Blower Tube and Nozzle

WARNING

Make sure the activation key is removed before starting

assembly. Never operate your blower without a properly

mounted blower tube and nozzle, @ 5.7.4. Use only

attachments supplied or expressly approved by STIHL,

@ 5.5.

To mount the blower tube and nozzle:

► Align the holes on the nozzle(2) with the lugs on the

blower tube(3).

► Push the nozzle(1) onto the blower tube(4).

The nozzle will engage with an audible click. Once the

nozzle and blower tube are assembled, keep them

connected during use and storage.

► Align the blower tube mounting lugs(6) with the grooves

on the blower tube(5) and push the parts together.

► Rotate the blower tube toward the symbol until it stops.

The blower tube should lock in position.

13.1 Inserting the Activation Key

WARNING

To reduce the risk of severe personal injury from unintended

activation, never store the activation key in the blower.

12 Assembling the Blower

0000-GXX-2268-A0

20-40%

40-60%

60-80%

80-100%

0-20%

1

13 Inserting and Removing the Activation

Key

2

3

0000-GXX-2594-A0

1

4

5

6

0458-719-8221-A

18

English

14 Switching the Blower On and Off

To insert the activation key:

► Place the blower on a level surface.

► Insert the activation key (1) into the activation key

socket(2) with even, steady pressure until it stops.

Inserting the activation key enables the flow of electrical

power from the integrated battery to the motor.

13.2 Removing the Activation Key

WARNING

To reduce the risk of severe personal injury from unintended

activation, always remove the activation key before

assembling, transporting, adjusting, cleaning, servicing,

maintaining or storing the blower and any other time it is not

in use.

To remove the activation key:

► Release the trigger switch.

► Place the blower on a level surface.

► Remove the activation key with even, steady pressure.

► Store the activation key away from the blower in a safe

place that is inaccessible to children and other

unauthorized users.

14.1 Switching On

WARNING

Never operate your blower if it is modified, damaged,

improperly adjusted or maintained, not completely and

securely assembled or not functioning properly, @ 5.5. To

reduce the risk of personal injury, always wear proper

clothing and protective apparel, including proper eye

protection, when operating your blower, @ 5.4.

Before switching on:

► Make sure you have a secure and firm footing.

► Stand upright.

► Always hold and operate the blower with one hand firmly

on the control handle.

To switch the blower on:

► Insert the activation key.

► Unlock the retaining latch(1) by pushing it forward with

your thumb. Hold it in this unlocked position.

► Depress and hold the trigger switch lockout(2).

The retaining latch can be released and will stay in the

unlocked position.

0000-GXX-2269-A0

1

2

14 Switching the Blower On and Off

1

0000-GXX-2270-A0

2

3

La page est en cours de chargement...

STIHL BGA 45 Manuel utilisateur

STIHL BGA 45 Manuel utilisateur

dans d''autres langues

Documents connexes