STIHL BGA 86 Manuel utilisateur

Catégorie
Souffleurs / sécheurs d'air
Taper
Manuel utilisateur
STIHL BGA 86
Instruction Manual
Notice d’emploi
G Instruction Manual
1 - 28
F Notice d’emploi
29 - 58
Original Instruction ManualPrinted on chlorine-free paper
Printing inks contain vegetable oils, paper can be recycled.
© ANDREAS STIHL AG & Co. KG 2019
0458-824-8221-A. VA0.J19.
0000008994_001_GB
0458-824-8221-A
English
1
This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process
with electronic systems.
Contents
1 Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2 Guide to Using this Manual
. . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.1 Signal Words
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.2 Symbols in Text
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3 Main Parts
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3.1 Blower and Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
4 Safety Symbols on the Products
. . . . . . . . . . . . . . . . . . . . .
3
4.1 Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
4.2 Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
5 IMPORTANT SAFETY INSTRUCTIONS
. . . . . . . . . . . . .
5
5.1 Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5.2 Intended Use
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5.3 Operator
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5.4 Personal Protective Equipment
. . . . . . . . . . . . . . . . . . . . . .
6
5.5 Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
5.6 Using the Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6 Battery Safety
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
6.1 Warnings and Instructions
. . . . . . . . . . . . . . . . . . . . . . . . . .
10
7 Maintenance, Repair and Storage
. . . . . . . . . . . . . . . . . .
12
7.1 Warnings and Instructions
. . . . . . . . . . . . . . . . . . . . . . . . . .
12
8 General Warnings and Instructions
. . . . . . . . . . . . . . . . .
13
8.1 General Safety Warnings and Instructions for
Battery-Powered Products
. . . . . . . . . . . . . . . . . . . . . . . . . .
13
9 Before Starting Work
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
9.1 Preparing the Blower for Operation
. . . . . . . . . . . . . . . . .
14
10 Charging the Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
10.1 Setting up the Charger
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
10.2 Charging
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
11 LED Diagnostics and Acoustic Signals
. . . . . . . . . . . . .
15
11.1 STIHL AP Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
11.2 STIHL AR Backpack Battery
. . . . . . . . . . . . . . . . . . . . . . .
16
12 STIHL AR Backpack Battery
. . . . . . . . . . . . . . . . . . . . . . . .
17
12.1 Positioning the Connecting Cord
. . . . . . . . . . . . . . . . . . .
17
12.2 Putting on the Harness
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
13 Assembling the Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
13.1 Mounting and Adjusting the Nozzle
. . . . . . . . . . . . . . . . .
19
14 Inserting and Removing the Battery
. . . . . . . . . . . . . . . .
19
14.1 Inserting the Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
14.2 Removing the Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
15 Switching the Blower On and Off
. . . . . . . . . . . . . . . . . . .
20
15.1 Switching On
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
15.2 Switching Off
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
16 Checking the Controls
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
16.1 Testing the Controls
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
17 During Operation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
17.1 Using the Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
18 After Finishing Work
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
18.1 Preparing for Transportation or Storage
. . . . . . . . . . . .
22
19 Transporting the Blower and Battery
. . . . . . . . . . . . . . .
22
19.1 Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
19.2 Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
20 Storing the Blower and Battery
. . . . . . . . . . . . . . . . . . . . .
23
20.1 Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
20.2 Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
21 Cleaning
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
21.1 Cleaning the Blower and Battery
. . . . . . . . . . . . . . . . . . .
24
22 Inspection and Maintenance
. . . . . . . . . . . . . . . . . . . . . . .
24
22.1 Inspecting and Maintaining the Blower
. . . . . . . . . . . . .
24
23 Troubleshooting Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
23.1 Blower and Battery
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
24 Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
24.1 STIHL BGA 86
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
24.2 Symbols on the Blower and Battery
. . . . . . . . . . . . . . . .
27
24.3 Engineering Improvements
. . . . . . . . . . . . . . . . . . . . . . . . .
27
0458-824-8221-A
2
English
1 Introduction
Thank you for your purchase. The information contained in
this manual will help you receive maximum performance and
satisfaction from your blower and, if followed, reduce the risk
of injury from its use.
SAVE THIS MANUAL!
Have your authorized STIHL servicing dealer show you how
to operate your power tool.
Do not lend or rent the blower without this instruction
manual. Allow only persons who fully understand the
information in this manual to operate the blower.
For further information, or if you do not understand any of
the instructions in this manual, please go to
www.stihlusa.com (for Canada: www.stihl.ca) or contact
your authorized STIHL servicing dealer.
2.1 Signal Words
This manual contains safety information that requires your
special attention. Such information is introduced with the
following symbols and signal words:
DANGER
Indicates a hazardous situation that, if not avoided, will
result in death or serious injury.
24.4 EMC Compliance Statement for Power Tool and
Charger
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
25 Replacement Parts and Equipment
. . . . . . . . . . . . . . . . .
27
25.1 Genuine STIHL Replacement Parts
. . . . . . . . . . . . . . . .
27
26 Disposal
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
26.1 Disposal of the Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
26.2 Battery Recycling
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
1 Introduction
Because a blower is a high-speed battery-
powered tool, special safety precautions must
be observed to reduce the risk of personal injury.
Read this instruction manual thoroughly before
use and periodically thereafter. Follow all safety
precautions. Careless or improper use of the
blower can cause serious or fatal injury.
2 Guide to Using this Manual
0458-824-8221-A
3
English
3 Main Parts
WARNING
Indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
NOTICE
Indicates a risk of property damage, including damage to the
machine or its individual components.
2.2 Symbols in Text
The following symbol is included to assist you with the use
of the manual:
3.1 Blower and Battery
1 Nozzle
Directs and concentrates the airstream.
2Blower Tube
Directs the airstream.
3 Intake Screen
Fits over the air intake opening.
4 Battery Compartment
Holds the battery.
5 Locking Lever
Secures the battery in the battery compartment.
6 Control Handle
The blower's handle.
7 Ergo-Lever
Holds the retaining latch in the unlocked position.
8 Retaining Latch
Locks/unlocks the trigger switch.
9 Trigger Switch
Switches the motor on and off.
10 Battery
Supplies electrical power to the motor.
11 Battery LEDs
Indicate the battery's state of charge and display error
messages regarding potential malfunctions in the battery
or power tool.
12 Push Button
Activates the battery‘s LEDs.
# Rating Plate
Contains electrical information and the product's serial
number.
4.1 Blower
The following safety symbols are found on the blower.
Refers to a designated chapter or sub-chapter in this
instruction manual.
3Main Parts
7
6
8
9
1
2
5
#
4
3
10
11
12
#
0000-GXX-9902-A0
4 Safety Symbols on the Products
0458-824-8221-A
4
English
4 Safety Symbols on the Products
4.2 Battery
The following safety symbols are found on the AR series
backpack battery and the AP series battery:
AR 900, 1000, 2000, 3000 Backpack Batteries
AR L Backpack Batteries
AP Series Batteries
Batteries sold separately.
To reduce the risk of injury, follow the specified
safety precautions.
Read and follow all safety precautions in the
instruction manual. Improper use can lead to
serious or fatal personal injury or property
damage.
To reduce the risk of eye and head injury, always
wear proper eye protection, @ 5.4.
To reduce the risk of personal injury from thrown
objects. Never direct the air flow toward
bystanders or pets, @ 5.6.4.
To reduce the risk of personal injury, keep hair
and loose-fitting clothing away from the air
intake, @ 5.4.
To reduce the risk of injury or property damage
from unintended activation, remove the battery
any time the blower is not in use, @ 5.5.
To reduce the risk of personal injury from
high velocity air flow and blown objects,
keep bystanders at least 17 ft. (5 m) away,
@ 5.6.4.
To reduce the risk of injury, follow the specified
safety precautions.
5m (17 ft)
Read and follow all safety precautions in the
battery's instruction manual and the manual for
the STIHL tool powered by this battery. Improper
use can lead to serious or fatal personal injury or
property damage.
To reduce the risk of personal injury or property
damage from fire, explosion or burns, including
chemical burns, do not disassemble, crush,
drop, damage or heat above 212 °F (100 °C).
Never expose to fire or incinerate, @ 6.1.
To reduce the risk of personal injury or property
damage from fire, use and store only within an
ambient temperature range of 14 °F to
122 °F (
-
10 °C to 50 °C), @ 6.1.
To reduce the risk of personal injury or property
damage from a short circuit, fire or explosion,
keep dry. Protect from rain, water, liquids and
damp conditions. Never immerse in water or
other liquids, @ 6.1.
To reduce the risk of personal injury or property
damage from a short circuit, fire or explosion,
keep dry. Never immerse in water or other
liquids, @ 6.1.
To reduce the risk of personal injury or property
damage from a short circuit, fire or explosion,
keep dry. Never immerse in water or other
liquids, @ 6.1.
0458-824-8221-A
5
English
5 IMPORTANT SAFETY INSTRUCTIONS
5.1 Introduction
When using an electric blower, basic precautions should
always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THE
BLOWER!
SAVE THESE INSTRUCTIONS
WARNING
To reduce the risk of fire, explosion, electric shock or other
personal injury, read and follow the important safety
instructions in this chapter. Additional important warnings
and instructions are provided in subsequent chapters of
this manual.
5.2 Intended Use
WARNING
This blower is designed for blowing leaves, grass, and
similar lightweight material from yards, gardens,
sidewalks, driveways, decks, patios and comparable
surfaces in the manner and in the conditions described in
this manual. Use of the blower for operations different
than intended could result in serious injury or death.
Blow leaves, grass, and similar lightweight material
only.
Improper use could result in personal injury or property
damage, including damage to the blower.
Use the blower and battery only as described in this
manual.
Never attempt to modify or override the blower's
controls or safety devices in any way.
Never use a blower that has been modified or altered
from its original design.
This power tool may be powered by a STIHL AP series
battery. Alternatively, it may be powered by a STIHL
AR series backpack battery in combination with an AP
adapter.
Batteries, chargers and other accessories are sold
separately.
5.3 Operator
WARNING
Working with the blower can be strenuous. The operator
must be in good physical condition and mental health. To
reduce the risk of personal injury from fatigue and loss of
control:
Check with your doctor before using the blower if you
have any health condition that may be aggravated by
strenuous work.
Do not operate the blower while under the influence
of any substance (drug, alcohol or medication, etc.)
that might impair vision, balance, dexterity or
judgment.
Be alert. Do not operate the blower when you are
tired. Take a break if you become tired.
Do not permit minors to use the blower.
According to STIHL's current knowledge, the electric
motor of this blower should not interfere with a
pacemaker.
However, persons with a pacemaker or other
implanted medical device should consult their
physician and device manufacturer before operating
this blower.
5 IMPORTANT SAFETY
INSTRUCTIONS
0458-824-8221-A
6
English
5 IMPORTANT SAFETY INSTRUCTIONS
5.4 Personal Protective Equipment
WARNING
To reduce the risk of personal injury:
Always wear proper clothing and protective apparel,
including proper eye protection.
Loss of control and severe injuries may result if hair,
clothing or apparel are drawn into the air intake or
otherwise become entangled in the components of the
blower. To reduce the risk of severe personal injury:
Wear a long-sleeve shirt or jacket.
To reduce the risk of eye injury:
Good footing is very important. To help maintain a secure
footing and reduce the risk of injury while working:
To help reduce the risk of personal injury caused by loss
of control during operation:
5.5 Blower
WARNING
This battery-powered blower is intended only for garden
and landscape maintenance. Use for other purposes may
increase the risk of personal injury and property damage.
Read and follow the operating instructions in this
manual for approved applications, @ 17.
To reduce the risk of personal injury to the operator and
bystanders:
Although certain unauthorized attachments may fit STIHL
blowers, their use may be extremely dangerous. Only
attachments supplied by STIHL or expressly approved by
STIHL for use with this specific model are recommended.
Use only attachments supplied or expressly
approved by STIHL.
Never modify this blower in any way.
Never attempt to modify or override the blower's
controls or safety devices in any way.
Never use a blower that has been modified or altered
from its original design.
Do not put any object into the openings of the
blower.
Do not use the blower with any openings blocked.
Keep the blower free of dust, lint, hair and anything
that might reduce air flow.
Wear sturdy and snug-fitting clothing that
also allows complete freedom of
movement.
Wear overalls or long pants made of
heavy material to help protect your legs.
Do not wear shorts.
Avoid loose-fitting jackets, scarves,
neckties, flared or cuffed pants, jewelry
and any other apparel that could be
drawn into the air intake.
Secure hair above shoulder level before
starting work.
Always wear goggles or close-fitting
protective glasses with adequate side
protection that are impact-rated and
marked as complying with CSA Z94.
Wear substantial footwear with non-slip
soles. Do not wear sandals, flip-flops,
open-toed or similar footwear.
STIHL recommends wearing heavy-duty
non
-
slip work gloves made of leather or
another wear-resistant material when
handling the blower.
Always release the trigger switch and
remove the battery before assembling,
transporting, adjusting, inspecting,
cleaning, servicing, maintaining or
storing the blower, and any other time it
is not in use.
0458-824-8221-A
7
English
5 IMPORTANT SAFETY INSTRUCTIONS
If the blower is dropped or subjected to similar heavy
impacts:
Check that it is undamaged, in good condition and
functioning properly before continuing work.
Check that the controls and safety devices are
working properly.
Check the LEDs for error messages, @ 11.1.2.
Check that the battery has not been damaged.
Never use or charge a malfunctioning, damaged,
cracked, leaking or deformed battery.
Never work with a damaged or malfunctioning
blower or battery. In case of doubt, have the blower
and battery checked by your authorized STIHL
servicing dealer.
If the blower or battery is damaged, not working properly,
has been left outdoors, exposed to rain or damp
conditions or dropped into water or other liquid, its
components may no longer function properly and safety
devices may be inoperative. To reduce the risk of personal
injury and property damage:
Take the blower and battery to your authorized
STIHL servicing dealer to be checked before further
operation.
Genuine STIHL replacement parts are specifically
designed to match your blower and meet safety and
performance requirements. Use of parts that are not
authorized or approved by STIHL may cause serious or
fatal injury or property damage.
STIHL recommends that only identical replacement
parts be used.
5.6 Using the Blower
5.6.1 Before Operation
WARNING
Misuse or unauthorized use may result in personal injury
and property damage.
Use the blower only as described in this instruction
manual.
Using a blower that is modified, damaged, improperly
adjusted or maintained, or not completely and securely
assembled can lead to a malfunction and increase the risk
of serious personal injury.
Never operate a blower that is modified, damaged,
improperly maintained or not completely and
securely assembled.
Always check your blower for proper condition and
operation before starting work, particularly the
retaining latch, Ergo-Lever and trigger switch.
Ensure that the retaining latch, Ergo-Lever and
trigger switch move freely and always spring back to
the stop position when released. The trigger switch
must not engage until the retaining latch is unlocked
and the Ergo-Lever is depressed.
Never attempt to modify or override the controls or
safety devices in any way.
If your blower or any part is damaged or does not
function properly, take it to your authorized STIHL
servicing dealer. Do not use the blower until the
problem has been corrected.
Before inserting the battery:
Check the electrical contacts in the battery
compartment for corrosion or other foreign matter.
Keep clean.
Never insert or use a malfunctioning, damaged,
cracked, leaking or deformed battery.
Read and follow the instructions on switching on the
blower, @ 15.1.
0458-824-8221-A
8
English
5 IMPORTANT SAFETY INSTRUCTIONS
To help reduce the risk of serious personal injury from
unintentional starting:
Be sure the retaining latch is in the locked position
and the trigger switch is in the off position before
inserting the battery.
Never carry the blower with your finger on the trigger
switch.
Release the trigger switch before removing the
battery.
Never leave the blower unattended when the battery
is inserted.
Never store the battery in the blower.
5.6.2 Holding and Controlling the Blower
WARNING
To maintain a firm grip and properly control your blower:
Keep the handle clean and dry at all times. Keep it
free of moisture, pitch, oil, grease and resin.
To reduce the risk of serious or fatal injuries to the
operator or bystanders from loss of control:
Always hold the blower firmly with one hand when
you are working.
Wrap your fingers tightly around the handle, keeping
the handle cradled between your thumb and
forefinger (see illustration above).
To reduce the risk of serious or fatal injuries to the
operator or bystanders from loss of control, keep proper
footing and balance at all times:
Never work on a ladder, roof, in a tree or while
standing on any other insecure support.
Take special care in overgrown or wet terrain and
always watch for hidden obstacles such as tree
stumps, roots, rocks, holes and ditches to avoid
stumbling.
Be extremely cautious when working on slopes or
uneven ground.
Use extra care when working on stairs.
For better footing, always clear away fallen
branches, scrub, cuttings and other material, objects
or vegetation that can increase the danger of
slipping, tripping or falling.
Never operate the blower above shoulder height.
Do not overreach. Keep proper footing and balance
at all times.
Remove the battery before assembling,
transporting, adjusting, inspecting,
cleaning, servicing, maintaining or
storing the blower, and any other time it
is not in use.
0000-GXX-4495-A0
0458-824-8221-A
9
English
5 IMPORTANT SAFETY INSTRUCTIONS
5.6.3 Working Conditions
WARNING
Operate your blower only under good visibility during
favorable daylight conditions.
Postpone the work if the weather is windy, foggy,
rainy or inclement.
Your blower is a one-person machine.
Bystanders, especially children, and animals should
not be allowed in the area where it is in use.
Switch off the blower immediately if you are
approached.
To reduce the risk of injury to bystanders and
unauthorized users:
Never leave the blower unattended when the battery
is inserted.
Switch off the blower and remove the battery during
work breaks and any other time the blower is not in
use.
Operating the blower in certain dry, dusty conditions may
cause static electricity to build up in the blower tube,
nozzle and housing. This static electricity may discharge
suddenly with a spark. To reduce the risk of personal
injury following static discharge:
Never operate the blower in a location where
combustible gases, liquids, vapors, dusts or other
combustible materials and substances are present.
Sparks generated from operation of the blower may be
capable of igniting combustible gases, liquids, vapors,
dusts or other combustible materials and substances. To
reduce the risk of fire and explosion:
Never operate the blower in a location where
combustible gases, liquids, vapors, dusts or other
combustible materials and substances are present.
Read and follow recommendations issued by
government authorities (e.g., CCOHS) for identifying
and avoiding the hazards of combustible gases,
liquids, vapors, dusts or other combustible materials
and substances.
Use of this blower can generate dust and other
substances containing chemicals known to cause
respiratory problems, cancer, birth defects and other
reproductive harm.
Consult governmental agencies such as ECCC,
CCOHS and PHAC and other authoritative sources
on hazardous materials if you are unfamiliar with the
risks associated with the particular substances with
which you are working.
Inhalation of certain dusts, especially organic dusts such
as mold or pollen, can cause susceptible persons to have
an allergic or asthmatic reaction. Substantial or repeated
inhalation of dust or other airborne contaminants,
especially those with a smaller particle size, may cause
respiratory or other illnesses.
Control dust at the source where possible.
To the extent possible, operate the blower so that
the wind or operating process directs any dust, mist
or other particulate matter raised by the blower away
from the operator.
When respirable dust or other particulate matter
cannot be kept at or near background levels, always
wear a respirator that is approved by PHAC and
rated for worksite-specific conditions. Follow the
recommendations of governmental authorities (e.g.,
CCOHS/PHAC) and occupational and trade
associations.
If the surrounding ground is coated with a chemical
substance, such as pesticide or herbicide:
Read and follow the instructions and warnings that
accompanied the substance coating the vegetation
or surrounding ground.
0458-824-8221-A
10
English
6 Battery Safety
5.6.4 Operating Instructions
WARNING
In the event of an emergency:
Switch off the motor immediately and remove the
battery.
The blower fan between the air intake and output opening
rotates whenever the motor is running. To reduce the risk
of injury from contact with the blower fan:
Never operate the blower with a missing, cracked or
worn intake screen or housing.
Never operate the blower without a properly
mounted blower tube and nozzle.
Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts of the
blower.
The air flow from the blower can propel small objects at
high speed. To reduce the risk of eye or other serious
personal injuries to bystanders from blown objects:
Do not allow the blower to be used as a toy.
Switch off the blower immediately if you are
approached.
A missing, cracked or worn intake screen or housing may
result in an increased risk of injury from thrown objects.
Never operate a blower that has a missing, cracked
or worn intake screen or housing.
Inserting any foreign object into the air intake or nozzle
may result in property damage, including damage to the
blower itself, and serious injury to the operator or
bystanders as a result of the object or broken parts being
blown at high speed.
Never insert any objects into the nozzle or air intake
of the blower.
Immediately switch off the blower if it starts to vibrate
abnormally.
Using the blower to spread herbicides, pesticides,
fertilizers or other chemical substances can be dangerous
and may cause serious or fatal injury to persons and
damage to the environment.
Never use the blower to disperse or spread
chemicals of any kind.
6.1 Warnings and Instructions
WARNING
Read and follow the safety precautions on the battery and
all warnings and instructions that accompany it.
Keep bystanders and pets at least 17 ft.
(5 m) away when the blower is running.
Never direct the air flow toward
bystanders or pets.
5m (17 ft)
6 Battery Safety
0458-824-8221-A
11
English
6 Battery Safety
Use of unauthorized batteries can damage the power tool
and result in fire, explosion and personal injury and
property damage.
Use only genuine STIHL AR or AP series batteries
with this power tool.
Use of STIHL AR or AP series batteries for any purpose
other than powering STIHL power tools could be
extremely dangerous.
Use STIHL AR and AP series batteries only to power
compatible STIHL power tools.
Use of unauthorized chargers can damage the battery and
result in fire, explosion and personal injury and property
damage.
Charge STIHL AP series batteries only with genuine
STIHL AL 101, AL 300 or AL 500 series chargers.
Charge STIHL AR series backpack batteries only
with genuine STIHL AL 300 or AL 500 series
chargers.
The battery contains safety features and devices which, if
damaged, may allow the battery to generate heat, rupture,
leak, ignite or explode.
Never use or charge a malfunctioning, damaged,
cracked, leaking or deformed battery.
Never open, disassemble, crush, drop, subject to
heavy impact or otherwise damage the battery.
Never expose the battery to microwaves or high
pressures.
Never insert objects into the battery's cooling slots.
Extreme temperatures may cause the battery to generate
heat, rupture, leak, ignite or explode, resulting in severe or
fatal personal injury and property damage. Exposure to
temperatures outside the recommended temperature
range may also reduce battery life and performance.
To reduce the risk of personal injury and property damage
in the event the battery emits smoke, an unusual smell or
feels unusually hot while using, charging or storing:
Immediately discontinue using or charging the
battery. Contact the authorities in the event of fire or
explosion.
To reduce the risk of a short circuit, which could lead to
electric shock, fire and explosion:
Never bridge the battery terminals with wires or
other metallic objects.
Keep a battery that is not in use away from metal
objects (e.g., paper clips, nails, coins, keys).
Never transport or store the battery in a metal
container.
Store the battery indoors in a dry room.
Never store the battery in damp or corrosive
environments or in conditions that could lead to
corrosion of its metal components.
Protect the battery from exposure to corrosive
agents such as garden chemicals and de-icing salts.
Never heat the battery above 212 °F
(100 °C).
Never incinerate or place the battery on
or near fires, stoves or other high-
temperature locations.
Use and store the battery only within an
ambient temperature range of 14 °F to
122 °F (-10 °C to 50 °C).
Never store the battery in direct sunlight
or inside a vehicle in hot weather.
Keep STIHL AR 900,1000, 2000, 3000
backpack batteries dry. Protect from
rain, water and other liquids.
Attach the rain cover to the STIHL AR
series battery before starting work in rain
or in very damp conditions.
If a STIHL AP or AR L battery has been
exposed to rain during work, remove it
from the product and allow it to dry
indoors. Make sure it is completely dry
before charging or use.
Never immerse any STIHL battery in
water or other liquids.
0458-824-8221-A
12
English
7 Maintenance, Repair and Storage
Protect the battery from exposure to conductive
liquids such as salt water.
Do not attempt to repair, open or disassemble the
battery. There are no user-serviceable parts inside.
Leaking battery fluid is potentially harmful and can cause
skin and eye irritation, chemical burns and other serious
personal injury.
Avoid contact with skin and eyes.
Use an inert absorbent such as sand on spilled
battery fluid.
In the event of accidental contact, immediately rinse
the contact area thoroughly with mild soap and
water.
If fluid gets into your eye(s): do not rub. Rinse water
over the open eye(s) for at least 15 minutes and
seek medical attention.
A battery fire can be dangerous. To reduce the risk of
severe personal injury and property damage in the event
of fire:
Evacuate the area. Fire can spread rapidly. Stay
clear of any vapors generated and maintain a safe
distance.
Contact the fire department.
Although water can be used to put out a battery fire,
use of a multi-purpose dry chemical fire extinguisher
is preferable.
Consult the fire department regarding proper
disposal of a burned battery.
7.1 Warnings and Instructions
WARNING
There are no user-authorized repairs for the battery or
blower. To reduce the risk of fire, electric shock or other
personal injury and property damage:
Users may carry out only the cleaning and
maintenance operations described in this manual.
Strictly follow the cleaning and maintenance
instructions in the appropriate sections of this
instruction manual.
STIHL recommends that all repair work be
performed by authorized STIHL servicing dealers.
Unintentional starting may result in personal injury or
property damage.
Use of parts that are not authorized or approved by STIHL
may cause serious or fatal injury or property damage.
STIHL recommends that only identical replacement
parts be used for repair or maintenance.
To reduce the risk of short circuit and fire:
Keep the battery guides free of foreign matter. Clean
as necessary with a dry cloth or soft, dry brush.
Improper storage can result in unauthorized use, damage
to the blower and battery and an increased risk of fire,
electric shock and other personal injury or property
damage.
Remove the battery from the blower before storing.
Never store the blower and charger with the battery
inserted.
7 Maintenance, Repair and Storage
Remove the battery before inspecting
the blower or carrying out any cleaning,
maintenance or repair work, before
storing, and any other time the blower is
not in use.
0458-824-8221-A
13
English
8 General Warnings and Instructions
Store the blower and battery indoors in a dry, secure
place that cannot be accessed by children or other
unauthorized users.
Never store the battery in the blower, in the charger,
in a metal container or in a container with metal
objects (e.g., paper clips, nails, coins, keys).
Dropping the battery could result in personal injury or
property damage. To prevent the battery from falling
during removal:
Place the blower on a level surface.
Use care when ejecting the battery.
8.1 General Safety Warnings and Instructions for
Battery-Powered Products
This section contains the general safety warnings and
instructions for battery-powered products contained in
UL 2595 / CSA C22.2 No. 0.23.
WARNING
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire, explosion and/or serious injury or
property damage.
Prevent unintentional starting. Ensure the trigger switch is
in the off-position before inserting the battery, picking up
or carrying the blower. Carrying the blower with your finger
on the trigger switch or inserting the battery with the
trigger switch engaged increases the likelihood of
unintended starting and possible accidents.
Remove the battery from the blower before making any
adjustments, changing accessories, or storing. Such
preventive safety measures reduce the risk of starting the
blower accidentally.
Recharge only with the charger specified by STIHL. A
charger that is suitable for one type of battery may create
a risk of fire when used with another battery.
Use the blower only with the specifically designated
batteries. Use of any other battery may create a risk of fire
or explosion and personal injury or property damage.
When the battery is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails or other
small metal objects that can make a connection from one
terminal to another. Do not store it in a metal container.
Shorting the battery terminals together may cause burns
or a fire or explosion.
Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation, chemical burns or respiratory illness from
inhalation.
Do not use a battery or blower that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion and risk
of injury or property damage.
Do not expose a battery or the blower to fire or excessive
temperature. Exposure to fire or temperature above
212 °F (100 °C) may cause fire and explosion.
Follow all charging instructions and do not charge the
battery outside of the ambient temperature range
specified. Charging improperly or outside the specified
range may damage the battery and increase the risk of
fire.
Have servicing performed by a qualified repair person
using only authorized replacement parts. This will help
maintain the safety and performance of the product.
Do not modify or attempt to repair the blower or the battery
pack. Follow the instructions for use and care.
8 General Warnings and Instructions
0458-824-8221-A
14
English
9 Before Starting Work
9.1 Preparing the Blower for Operation
Before starting work:
Fully charge the battery, @ 10.
Mount the nozzle, @ 13.1.
Check the controls for proper function and condition,
@ 16.
10.1 Setting up the Charger
WARNING
Read and follow the safety precautions on the battery and
charger and all warnings and instructions that accompany
those products. To reduce the risk of short circuit, which
could lead to electric shock, fire and explosion, make sure
the charger and its components are dry and not damaged;
operate the charger indoors at an appropriate ambient
temperature.
WARNING
A typical household electric circuit is between 15 and 20
amps. A single STIHL AL 500 charger draws approximately
4.8 amps. A single AL 300 charger draws approximately
4.4 amps. To reduce the risk of fire from overloading an
electrical circuit:
Ensure the electrical system is rated to withstand the
expected electrical draw before charging your battery.
Charge multiple batteries one at a time or on separate
circuits, unless you know your circuit can handle the total
expected draw from multiple chargers.
WARNING
Since the charger heats up during the charging process, do
not operate the charger on a combustible surface or in a
location where combustible gases, liquids, vapors, dusts or
other materials and substances are present.
To set up the charger:
Insert the plug (3) into a properly installed electrical
outlet (4) matching the voltage and electrical frequency
stated on the rating plate on the charger.
The charger runs a self-test immediately after it is plugged
in. The charger LED (1) will glow green for about 1 second,
then it will glow red briefly before going out. Once the LED
goes out, the self-test is complete and the charger is ready
to charge the battery.
Position the power supply cord (2) so that it will not be
stepped on, tripped over, come in contact with sharp
objects or moving parts or otherwise be subjected to
damage or stress.
10.2 Charging
WARNING
STIHL batteries contain safety features and devices which,
if damaged, may allow the battery to generate heat, rupture,
leak, ignite or explode. Never charge a malfunctioning,
damaged, cracked, leaking or deformed battery, or use a
charger that has been damaged. Never insert a wet battery
9 Before Starting Work
10 Charging the Battery
3
2
0000-GXX-3228-A1
4
1
0458-824-8221-A
15
English
11 LED Diagnostics and Acoustic Signals
or battery adapter. Never use a wet charger. Follow all
product-specific warnings and instructions accompanying
your battery and charger.
A battery is not fully charged when it ships from the factory.
STIHL recommends that you fully charge the battery before
using it the first time.
Operate the charger only indoors, in dry rooms and within an
ambient temperature range of 41 °F to 104 °F (5 °C to
40 °C).
The battery heats up during operation of the power tool. If a
hot battery is connected to the charger, it may be necessary
for it to cool down before charging starts. The charging
process begins only after the battery has cooled down
sufficiently.
Charging time depends on a number of factors, including
battery condition and the ambient temperature. For a
complete list of approximate charging times, see
www.stihl.com/charging-times.
To charge an AR battery:
Push the plug of the connecting cord (1) into the
socket (2) of the AP Adapter (3) until it stops.
Push the AP Adapter into the charger (5) until it stops.
The LED on the charger (4) glows green when the battery
is charging.
The LEDs on the AR battery glow green and show the
state of charge.
When the LEDs on the battery turn off, the charging
process is complete and the charger will shut itself off.
Remove the AP Adapter from the charger and disconnect
the charger's power supply cord from the electrical outlet
when charging is complete.
Charge STIHL AR backpack batteries only with genuine
STIHL AL 300 or AL 500 series chargers.
To charge an AP battery:
Push the battery (2) into the charger (3) until it stops.
The LED on the charger glows green when the battery is
charging.
The LEDs (1) on the battery glow green and show the
state of charge.
When the LEDs on the battery go out, the charging
process is complete and the charger will shut itself off.
Remove the battery from the charger and disconnect the
charger's power supply cord from the electrical outlet.
Charge STIHL AP series batteries only with genuine
STIHL AL 101, AL 300 or AL 500 series chargers.
11.1 STIHL AP Battery
11.1.1 Battery Status
Four LEDs show the status of the battery. These LEDs can
glow or flash green or red.
3
2
1
0000-GXX-2680-A0
3
45
11 LED Diagnostics and Acoustic Signals
1
2
3
4
0000-GXX-3918-A0
0458-824-8221-A
16
English
11 LED Diagnostics and Acoustic Signals
11.1.2 Power Tool Status
The same LEDs on the battery will indicate the status of the
power tool.
If three LEDs glow red continuously: the power tool motor is
too hot. Allow the motor to cool down.
If three LEDs flash red when you activate the trigger switch:
the power tool has an electrical malfunction. Do not operate
the power tool. Have it checked by an authorized STIHL
servicing dealer before use or storage.
For troubleshooting information, @ 23.
11.1.3 Charge Status
The LEDs on the battery also show the battery's state of
charge.
To determine the battery's state of charge:
Press the button (1) on the battery.
The LEDs on the battery will glow or flash green for about
5 seconds and indicate the state of charge (see
illustration).
For example:
If four green LEDs glow continuously: full charge.
If one green LED is flashing: less than 20 % charge.
11.2 STIHL AR Backpack Battery
11.2.1 Battery Status
Six LEDs and an acoustic signal indicate the status of the
battery.
1 A short beep
The acoustic signal works as it should.
2 AR Series four or six (AR L) long beeps
The battery's charge is low. Recharge the battery.
3 Rapid succession of short beeps
There is a malfunction in the battery. The signal stops
automatically after a few seconds. Do not attempt to
charge, use or store the battery. Replace the battery.
These LEDs can glow or flash green or red.
If one LED glows red continuously: the battery is
either too hot or too cold. Allow the battery to
warm up or cool down gradually at an ambient
temperature of about 50 °F to 68 °F (10 °C to
20 °C).
If all 4 LEDs flash red: the battery has a
malfunction and must be replaced. Do not
attempt to charge, use or store the battery.
1
0000-GXX-1248-A0
20-40%
40-60%
60-80%
80-100%
0-20%
1
2
3
.......
0000-GXX-3229-A1
0458-824-8221-A
17
English
12 STIHL AR Backpack Battery
Be aware that your ability to hear the acoustic signal may
be reduced when wearing hearing protection.
11.2.2 Power Tool Status
When the battery is connected to the power tool, the same
LEDs on the battery will indicate the status of the power tool.
If three LEDs glow red continuously: the power tool motor is
too hot. Allow the motor to cool down.
If three LEDs flash red when you activate the trigger switch:
the power tool has an electrical malfunction. Do not operate
the power tool. Have it checked by an authorized STIHL
servicing dealer before use or storage.
For troubleshooting information, @ 23.
11.2.3 Charge Status
The LEDs and acoustic signals on the battery also indicate
the battery's state of charge.
To determine the battery's state of charge:
Press the button (1) on the backpack battery.
A single short beep will be emitted. The LEDs on the battery
will glow or flash green for about 5 seconds and indicate the
state of charge (see illustration).
For example:
If six green LEDs glow continuously: full charge.
If one green LED is flashing and four long beeps are emitted:
less than 20 % charge.
12.1 Positioning the Connecting Cord
WARNING
To reduce the risk of injury from tripping on the connecting
cord or losing control of the power tool, always secure the
connecting cord with the hook and eye fasteners as
described below. Always position and secure the connecting
cord so that it will not interfere with the proper working
technique as described in the instruction manual for the
power tool you are using, or your ability to maintain control
of the power tool.
If one LED glows red continuously: the battery is
either too hot or too cold. Allow the battery to
warm up or cool down gradually at an ambient
temperature of about 50 °F to 68 °F (10 °C to
20 °C).
If the four right side LEDs flash red and a rapid
succession of several short beeps is emitted: the
battery has a malfunction and must be replaced.
Do not attempt to charge, use or store the
battery.
12 STIHL AR Backpack Battery
0000-GXX-2673-A0
100 % 0 %
0458-824-8221-A
18
English
12 STIHL AR Backpack Battery
WARNING
Manage the cord to prevent it from contacting the
cutting/working attachment or catching on objects, which
could cause you to lose balance or control of the power tool,
resulting in serious personal injury and property damage.
The connecting cord can be secured in different positions
and adjusted to suit the height and reach of the operator.
The connecting cord can run through the guide (1) on the
shoulder strap (Illustration A), or along the back
plate (Illustration B). Secure the connecting cord to the
harness with the hook and eye fasteners (2). Always secure
the connecting cord using the guide or hook and eye
fasteners on the side of the body on which the power tool is
held and controlled. Do not allow the connecting cord to
swing across your body or hang at your side.
The length of the connecting cord can be adjusted by
making a loop around the top (Illustration C) or on the side
(Illustration D) of the backpack battery with the hook and eye
fasteners.
12.2 Putting on the Harness
WARNING
The operator must be able to remove the backpack battery
quickly in the event of an emergency. In an emergency,
open and remove the waist belt and chest strap quickly
before dropping the battery to the ground.
To ensure a proper fit:
Put the backpack battery on your back.
Fasten and adjust the waist belt (2) so that it rests
comfortably but securely on your hips.
Fasten the chest strap (1) and adjust it so that it fits
comfortably but securely across your chest.
1
2
2
2
2
A B
0000-GXX-9303-A0
0000-GXX-9304-A0
C
D
1
0000-GXX-2828-A0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

STIHL BGA 86 Manuel utilisateur

Catégorie
Souffleurs / sécheurs d'air
Taper
Manuel utilisateur

dans d''autres langues