Pioneer XDJ-RX2-W Guide de démarrage rapide

Marque: Pioneer

Modèle: XDJ-RX2-W

Catégorie: Contrôleurs DJ

Taper: Guide de démarrage rapide

Ce manuel convient également à

XDJ-RX2

Français Deutsch ItalianoEnglish

XDJ-RX2

pioneerdj.com/support/

rekordbox.com/

Operating Instructions (Quick Start Guide)

Mode d’emploi (Guide de démarrage rapide)

Bedienungsanleitung (Kurzanleitung)

Istruzioni per l’uso (Guida di avvio veloce)

DJ SYSTEM

SYSTÈME DJ

DJ-SYSTEM

SISTEMA DJ

For FAQs and other support information for this product, visit the above site.

Pour les FAQ et autres informations de support sur ce produit, consultez le site ci-dessus.

Häufig gestellte Fragen und weitere Support-Informationen für dieses Produkt finden Sie auf der oben

genannten Seite.

Per la sezione FAQ e altre informazioni di supporto per questo prodotto, visitare il sito indicato sopra.

CAUTION

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER

-SERVICEABLE

RTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

D3-4-2-1-1_B1_En

WARNING

This equipment is not waterproof

. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture

D3-4-2-1-3_A1_En

WARNING

This product equipped with a three-wire grounding

(earthed) plug - a plug that has a third (grounding) pi

This plug only fits a grounding-type power outlet. If you

are unable to insert the plug into an outlet, contact a

licensed electrician to replace the outlet with a properly

grounded one. Do not defeat the safety purpose of the

grounding plug.

D3-4-2-1-6_A1_En

WARNING

prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Operating Envir

onment

Operating environment temperature and humidit

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light).

D3-4-2-1-7c*_A2_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 5 cm at rear

, and 5 cm at each side).

D3-4-2-1-7d*_A1_En

CAUTION

The switch on this unit will not completely shut off

all power from the AC outlet. Since the power cord

serves as the main disconnect device for the unit,

you will need to unplug it from the AC outlet to shut

down all power. Therefore, make sure the unit has

been installed so that the power cord can be easily

unplugged from the AC outlet in case of an accident.

To avoid fire hazard, the power cord should also be

unplugged from the AC outlet when left unused for a

long period of time (for example, when on vacation).

D3-4-2-2-2a*_A1_En

When using this product, confirm the safety

information shown on the bottom of the unit.

D3-4-2-2-4_B1_En

CAUTION

This product is evaluated in moderate and tropical

climate condition.

D3-8-2-1-7a_A1_En

The graphical symbol placed on the product

means alternating current.

The graphical symbol placed on the product

means direct current.

The graphical symbol placed on the product

means Class II equipment.

D3-8-2-4_A1_En

Recording equipment and copyright: Recording

equipment should be used only for lawful copying

and you are advised to check carefully what is lawful

copying in the country in which you are making a

copy. Copying of copyright material such as films or

music is unlawful unless permitted by a legal

exception or consented to by the rightowners.

K018_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used

electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

rivate households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to

designated collection facilities or to a retailer (if you purchase a similar new one)

r countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessar

y treatment, recovery and recycling and thus prevent potential

negative effects on the environment and human health.

K058b_A1_En

D3-4-2-1-6b_B1_En

Laite on liitettävä suojamaadoituskoskettimilla

varustettuun pistorasiaan

For Finland customers

For Norway customers

For Sweden customers

Apparatet må tilkoples jordet stikkontakt

For Denmark customers

Apparatets stikprop skal tilsluttes en stikkontakt med

jord, som giver forbindelse til stikproppens jord.

Apparaten skall anslutas till jordat uttag

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on

. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest se

rvice center or your

dealer for a replacement.

S002*_A1_En

English

Contents

How to read this manual

! Thank you for purchasing this Pioneer DJ product.

Read this manual and the Operating Instructions that is available on

the Pioneer DJ site before using the product. Both contain important

information that you should understand to properly use the product.

Be sure to read the “Safety Precautions”. Keep this manual and the

“Warranty” included at the end of this manual in a safe place.

For obtaining the Operating Instructions for this product, see

Obtaining the Operating Instructions (p. 5 ).

! In this manual, names of channels and buttons on the product, etc.,

are enclosed in square brackets ([ ]). (e.g. [CH1], [USB STOP] button)

Before start

Features ....................................................................................................... 5

Obtaining the Operating Instructions....................................................... 5

Accessories ................................................................................................. 5

Preparing the software ............................................................................... 5

Supported media ........................................................................................ 6

Part names

Power section .............................................................................................. 7

USB section................................................................................................. 7

Deck section ................................................................................................ 7

Browse section ........................................................................................... 8

Mixer/effect section .................................................................................... 8

Connections

Connecting input/output terminals ........................................................ 10

Operation

Playback .................................................................................................... 13

Outputting sound ..................................................................................... 13

Monitoring sound with headphones ....................................................... 14

Turning off the system .............................................................................. 14

Additional information

Troubleshooting ........................................................................................ 15

Error messages ......................................................................................... 17

Changing the settings .............................................................................. 17

Cleaning the touch display ...................................................................... 17

Trademarks and registered trademarks ................................................. 17

Software license notice ............................................................................ 17

Cautions on copyrights ............................................................................ 17

Specifications............................................................................................ 18

English

Before start

Features

This unit is a system integrating a DJ player and DJ mixer in a single

unit and inherits the technology of the Pioneer DJ CDJ series and DJM

series, the world standard for club equipment. Full-fledged DJ perfor-

mances can be made using tracks on USB devices and computers.

Obtaining the Operating

Instructions

Some operating instructions are provided in PDF files.

Adobe

Reader

is required to view the PDF files.

1 Launch a web browser on a computer and access the

following Pioneer DJ support site.

pioneerdj.com/support/

2 Click [Manuals] under [XDJ-RX2].

3 Click on the desired language on the download page.

Download of the Operating Instructions starts.

Accessories

! Power cord

! USB cable

! Operating Instructions (Quick Start Guide) (this document)

! Warranty (for some regions)

! Software license notice

! rekordbox dj license key card

1 The included warranty is for the European region.

Caution

The license key cannot be reissued. Be careful not to lose it.

Preparing the software

Music management software, rekordbox, and the driver software are not

included with this product.

Access the rekordbox site and Pioneer DJ support site, and download

the rekordbox software and driver software respectively.

! Prepare a computer, network devices, etc., that are required to

access the internet.

About rekordbox and rekordbox dj

! rekordbox is a composite software that enables track management

and DJ performances. Music files on computers and mobile devices

can be managed (analysis, setting, creation, and history storage)

with the music management software rekordbox. Excellent DJ per-

formances can be achieved by using the music files managed by

rekordbox together with this unit.

! The DJ performance function of rekordbox is called rekordbox dj.

Enter the license key included with this product to use rekordbox dj.

! For information on the latest system requirements, compatibil-

ity, and supported operating systems of rekordbox, see [System

Requirements] from [Support] on the Pioneer DJ website (rekord-

box.com).

rekordbox.com

! Operation on all computers is not guaranteed even if the computers

meet the required operating environment.

! The CPU and hard disc may not provide sufficient processing capa-

bilities depending on the power-saving setting, etc. on the computer.

Confirm that the computer meets conditions to provide constant

high-performance (for example, connecting the computer to a power

outlet to maintain a stable power supply) especially when using

rekordbox on a laptop.

! A separate contract with an internet service provider and payment of

the utilization fee are required to access the internet.

! Use the latest version/service pack of the operating system.

 Obtaining the rekordbox software

1 Launch a web browser on the computer and access

the rekordbox.com site below.

rekordbox.com

2 Click [Download] in the [Download] menu of

“rekordbox.com”.

The rekordbox download page is displayed.

3 Click the download banner.

Downloading of rekordbox starts.

 Installation (Windows)

Do not connect this unit and the computer until the installation is

completed.

! Log in to the computer as the administrator before installation.

! Close all the applications running on the computer before

installation.

1 Unzip the downloaded rekordbox software file.

2 Double-click the rekordbox software to launch the

installer.

3 Read the terms of the license agreement carefully,

and if you agree, select [I agree to the license terms and

conditions], then click [Next].

After the installation destination is specified, the installation starts.

! If you do not agree to the license agreement, click [Close] to cancel

the installation.

4 If the installation completion screen appears, click

[Close] to close the rekordbox installer.

 Installation (Mac OS)

Do not connect this unit and the computer until the installation is

completed.

! Close all the applications running on the computer before

installation.

1 Unzip the downloaded rekordbox software file.

2 Double-click the rekordbox software to launch the

installer.

3 Read the license agreement, select [Agree] if you

agree to the terms.

Proceed by following the instructions on the screen.

! If you do not agree to the contents of the license agreement, click

[Disagree] to quit installation.

4 When the installation completion screen appears,

click [Close] to close the rekordbox installer.

 rekordbox (iOS/Android)

Tracks managed by rekordbox can be played by connecting the mobile

device on which rekordbox (iOS/Android) is installed via USB. For the

supported devices, see the Pioneer DJ website (rekordbox.com).

! For details on installing rekordbox (iOS/Android), see the Pioneer DJ

website (rekordbox.com).

Driver software

 Audio driver software

! Dedicated driver software is required for outputting audio signals

from a computer.

 USB (LINK Export) connections driver software

for rekordbox (Mac/Windows)

! Dedicated driver software is required for connecting the unit and

rekordbox (Mac/Windows) via USB (LINK Export).

 Obtaining the driver software

1 Launch a web browser on a computer and access the

following Pioneer DJ support site.

pioneerdj.com/support/

! For information on installing the driver software, see the Pioneer

DJ support site or the Operating Instructions for this product that is

available on the support site.

Supported media

This unit can play music files stored on USB mass storage devices

(external hard disks, portable flash memory devices, etc.).

Supported file

systems

FAT16, FAT32, HFS+ (NTFS is not supported.)

! Information such as cue points, loops points and hot cues can be

stored via USB.

! Depending on the USB device you are using, you may not achieve

the expected performance.

! There is no guarantee that all USB devices will operate on this unit.

For more information, refer to the Operating Instructions that is avail-

able on the Pioneer DJ support site.

English

Part names

For more information, refer to the Operating Instructions that is avail-

able on the Pioneer DJ support site.

1 Power section (page 7 )

2 USB section (page 7 )

3 Deck section (page 7 )

4 Browse section (page 8 )

5 Mixer/effect section (page 8 )

Power section

1 u switch

This switch is used to switch between standby and on.

USB section

1 USB 1, 2 STOP buttons

2 USB 1, 2 indicators

3 USB 1, 2 slots

4 MASTER REC (WAKE UP) button

5 TRACK MARK button

Deck section

d e f

1 LOOP OUT (OUT ADJUST) button

2 LOOP IN/4BEAT (IN ADJUST) button

3 RELOOP/EXIT button

4 DIRECTION, REV button

5 SLIP button

6 TRACK SEARCH o, p buttons

7 SEARCH m, n buttons

8 Jog dial

9 SHIFT button

a Jog dial display section

b CUE button

c f (PLAY/PAUSE) button

d CUE/LOOP CALL, c (LOOP 1/2X), d (LOOP 2X) buttons

e DELETE button

f MEMORY button

g VINYL SPEED ADJUST control

h VINYL MODE button

i SYNC/INST.DOUBLES button

j MASTER button

k TEMPO RANGE button

l MASTER TEMPO button

m TEMPO slider

n HOT CUE/CALL button

o BEAT LOOP button

p SLIP LOOP button

q BEAT JUMP button

r Performance pads

Browse section

8 9

1 QUANTIZE button

2 TIME MODE (AUTO CUE) button

3 USB 1, 2 buttons

4 MIDI button

5 rekordbox button

6 BROWSE button

7 TAG LIST button

8 INFO button

9 MENU (UTILITY) button

a BACK button

b TAG TRACK/REMOVE button

c Rotary selector

d SHORTCUT button

e TRACK FILTER/EDIT button

f Main display

g LOAD 1/2 button

Mixer/effect section

1 2

3 4

6 657 7

c c

1 MIC (OFF, ON, TALK OVER) selector switch

2 MIC (OFF, ON, TALK OVER) indicator

3 MIC EQ (HI, LOW) controls

4 MIC LEVEL (MIC1, MIC2) controls

5 MASTER LEVEL control

6 DECK1, 2, LINE1, 2, PHONO1, 2 selector switch

7 TRIM control

8 BOOTH MONITOR control

9 BEAT c, d buttons

a TAP (AUTO) button

b EQ/ISO (HI, MID, LOW) controls

c Channel Level Indicator

d Master level indicator

e BEAT EFFECTS selector switch

f COLOR control

g Effect channel selector switch

h CUE (CH1, CH2, MASTER) buttons

i TIME control

j CROSS FADER CURVE (THRU,

, ) (crossfader

curve selector switch)

k LEVEL/DEPTH control

English

l ON/OFF button

m Channel fader

n Crossfader

o HEADPHONES LEVEL control

p HEADPHONES MIXING control

q PARAMETER control

r SOUND COLOR FX (DUB ECHO, SWEEP, NOISE, FILTER)

buttons

s AUX TRIM control

t AUX selector switch

Connections

! Connect the power cord to a power outlet after all the connections are completed.

! Turn off this unit and disconnect the power cord from the power outlet before connecting components or changing the connections.

! Refer to the operating instructions for the components to be connected.

! Be sure to use the supplied power cord.

! Connect this unit and the computer directly using the included USB cable.

Connecting input/output terminals

Rear panel, front panel

1 62 3 4 5 7 7 9

8 c

Headphones

Power amplifier,

powered speakers,

etc.

Power amplifier,

powered speakers, etc.

Power amplifier

(for booth monitor)

software

Computer

Portable audio device

DJ player

Analog player

Microphone

To power outle

Power cord

Front panel

Rear panel

To power outle

Power cord

1 PHONES terminals

2 MASTER1 terminals

! Be careful not to accidentally insert the power cord of

another unit to [MASTER 1] terminal.

! Do not connect the terminal that can supply phantom

power to the [MASTER 1] terminal.

3 MASTER2 terminals

4 BOOTH terminals

5 Kensington security slot

USB terminal

This product satisfies electromagnetic noise

regulations when it is connected to other equipment

through shielded cables (with Ferrite-cores attached)

and connectors.

Use only the furnished accessory connecting cables.

D44-8-1-2b_A1_En

The ferrite-cores are for the purpose of preventing

electromagnetic noise, do not remove them.

D44-8-1-4_A1_En

7 LINE/PHONO terminals

8 AUX terminal

9 SIGNAL GND terminal

a MIC2 terminal

b MIC1 terminal

c AC IN

English

Basic style

Playback on this unit is performed mainly using tracks prepared with rekordbox installed on a computer.

For rekordbox operations, see the rekordbox (Mac/Windows) user’s manual from the [Help] menu of rekordbox (Mac/Windows).

 PRO DJ LINK (USB Export)

You can play music files prepared using rekordbox on this unit and also use the settings such as playlists, cues, loops and hot cues set by rekordbox.

Store music files and settings in a memory device (flash memory, hard disk, etc.) and connect it to this unit. Using PRO DJ LINK eliminates the need to

bring a computer into the DJ booth.

rekordbox

To power outle

Power cord

USB device on which

rekordbox data is recorded

Computer

1 Connect headphones to the [PHONES] terminal.

2 Connect powered speakers, power amplifier, etc. to the [MASTER1] or [MASTER2] terminal.

! To output sound from the [BOOTH] terminals, connect speakers, etc. to the [BOOTH] terminals.

3 Connect the power cord to the unit, and then connect the power plug to the power outlet.

4 Press the [u] switch on the rear panel of this unit to turn this unit on.

5 Turn on the devices connected to the output terminals (such as a power amplifier or powered speakers).

! When a microphone, DJ player or other external device is connected to the input terminals, the connected device also turns on.

 PRO DJ LINK (LINK Export)

! When a computer on which rekordbox is installed is taken into the DJ booth and connected to this unit using a USB cable, tracks in rekordbox can

be selected and played. This makes it possible to use the information such as playlists, cues, loops and hot cues that have been set ahead of time

with rekordbox for performances.

! When a mobile device on which rekordbox (iOS/Android) is installed is connected using a USB cable, tracks in rekordbox can be selected and

played. This makes it possible to use the information such as playlists, cues, loops and hot cues that have been set ahead of time with rekordbox for

performances.

! Install the driver software before connecting a USB device to a computer on which rekordbox (Mac/Windows) is installed. For details, see Driver

software on page 6 .

iPod and iPhone that can be connected to this product

! This product is compatible with iPhone7, iPhone7 Plus, iPhone SE, iPhone 6s, iPhone 6s Plus, iPhone 6, iPhone 6 Plus, iPhone 5s, iPhone 5c,

iPhone 5, iPhone 4s, and iPod touch (6th and 5th generations).

! For the latest supported devices, see the following Pioneer DJ website.

rekordbox.com

When using a USB cable

To power outlet

Power cord

rekordbox

Mobile device on which

rekordbox is installed

Computer

1 Connect the unit and the computer by using a USB cable, or connect the unit and the mobile device by inserting the

USB cable in the USB device insertion slot.

2 Connect headphones to the [PHONES] terminal.

3 Connect powered speakers, power amplifier, etc. to the [MASTER1] or [MASTER2] terminal.

! To output sound from the [BOOTH] terminals, connect speakers, etc. to the [BOOTH] terminals.

4 Turn on the power of the computer or the mobile device, and then launch rekordbox.

5 Connect the power cord to the unit, and then connect the power plug to the power outlet.

6 Press the [u] switch on the rear panel of this unit to turn this unit on.

7 Turn on the devices connected to the output terminals (such as a power amplifier or powered speakers).

! When a microphone, DJ player or other external device is connected to the input terminals, the connected device also turns on.

English

Operation

For more information, refer to the Operating Instructions that is avail-

able on the Pioneer DJ support site.

Playback

This section describes basic track selection operations and how to

switch the screen.

Playing music files on media connected

to this unit

1 Open the USB slot cover and connect a USB device.

2 Press a media button (either [USB1] or [USB2]).

Tracks and folders on the connected USB device are displayed in a list.

You can switch the device from which to display the contents to the main

display.

[USB1] button: Displays the contents of the USB device connected to the

USB1 slot.

[USB2] button: Displays the contents of the USB device connected to the

USB2 slot.

! The rekordbox library is displayed if it is stored in the connected USB

device.

3 Rotate the rotary selector.

Move the cursor to select an item.

! Press the rotary selector to move to a lower level in the folder. Press

the [BACK] button to return to the level above.

! When the [BACK] button is pressed for over 1 second or the medium

button for the medium being browsed is pressed, the display moves

to the topmost level.

4 Use the rotary selector to select the track you want to

load.

If the rotary selector is pressed while the cursor is placed over a track

title, the track menu is displayed.

5 Press the [LOAD1, 2] button.

The track is loaded into the specified deck of the unit and begins playing.

! When a track has been loaded while pausing, press the

[f (PLAY/PAUSE)] button to start playback.

! When auto cue is turned on, the disc pauses at the audio start posi-

tion. In this case, press the [f (PLAY/PAUSE)] to start playback.

 If the medium contains the rekordbox library

The rekordbox library is displayed if it is stored in the connected USB

device.

! Music files are displayed by categories (album, artist, etc.) set with

rekordbox.

Playing the rekordbox library on a

computer or mobile device

Music files are displayed by categories (album, artist, etc.) set with

rekordbox.

1 Press the [rekordbox] button.

The rekordbox library is displayed on the main display of this unit.

! Press the [USB] button to select a mobile device connected by USB.

2 Rotate the rotary selector.

Move the cursor to select an item.

3 Use the rotary selector to select the track you want to

load.

If the rotary selector is pressed while the cursor is placed over a track

title, the track menu is displayed.

4 Press the [LOAD1, 2] button.

The track is loaded into the specified deck of the unit and begins playing.

Outputting sound

Check that the unit and the external devices are properly connected

before outputting sound.

= Connecting input/output terminals (p. 10 )

Set the volume of the power amplifier or powered speakers connected to

the [MASTER1] and [MASTER2] terminals to an appropriate level. Note

that loud sound may be output if the volume is set too high.

Outputting the sound of channel 1 [CH1]

To output the sound of [CH 2] (channel 2), replace [CH1] with [CH 2],

[DECK 1] with [DECK 2], [PHONO1] with [PHONO2], and [LINE1] with

[LINE2] in the procedure below.

1 Switch the [DECK 1, LINE1, PHONO1] selector switch

of [CH1].

Select the input source for [CH1] from the devices connected to this

unit.

— [DECK 1]: Selects rekordbox, MIDI, USB1, USB2.

— [LINE1]: Selects the device connected to the [LINE1] terminals.

— [PHONO1]: Selects the device connected to the [PHONO1]

terminals.

2 Rotate the [TRIM] control in the [CH1] section

clockwise.

Adjust the level of sound input to the [CH1] terminal.

The [CH1] level indicator lights when audio signals are properly input to

[CH1].

Rotate the [TRIM] control to confirm that the orange indicator lights up

at the highest volume for the track.

Make sure that the red indicator does not light, or the sound may be

distorted.

3 Move the [CH1] channel fader to the back side.

The level of the sound output from [CH1] terminals is adjusted.

4 Set the [CROSS FADER CURVE THRU, , ] (the

crossfader curve selector switch).

Sets the curve characteristics of the crossfader.

5 Set the crossfader.

Switch the channel whose sound is output from the speakers.

— Left edge: The [CH1] sound is output.

— Center position: The sound of [CH1] and [CH 2] is mixed and

output.

— Right edge: The [CH 2] sound is output.

! This operation is not necessary when the [CROSS FADER CURVE

(THRU, , )] (crossfader curve selector switch) is set to

[THRU].

6 Rotate the [MASTER LEVEL] control clockwise.

Sound is output from the speakers.

The master level indicator lights.

Rotate the [MASTER LEVEL] control to confirm that the orange indicator

lights up at the highest volume for the track.

! Make sure that the master level indicator does not light, or the sound

may be distorted.

Monitoring sound with headphones

1 Connect headphones to the [PHONES] terminal.

2 Press the [CUE] button of the channel to be

monitored.

3 Rotate the [HEADPHONES MIXING] control.

Adjust the balance of the volume between the channel selected with the

[CUE] button and MASTER.

4 Rotate the [HEADPHONES LEVEL] control.

Adjust the volume of the headphones.

Setting monitor output

The [MONO SPLIT, STEREO] setting can be changed with UTILITY.

! [MONO SPLIT]: Outputs the sound of the channel selected with the

[CUE] button to [L] and the sound of MASTER to R.

! [STEREO]: Outputs the sound selected with the [CUE] button in

stereo.

For details on the functions, see the Operating Instructions for this

product.

Turning off the system

1 Press the [USB STOP] button for over 2 seconds.

Do not disconnect the USB device or turn off this unit while the USB

indicator is lit or flashing. Doing so could delete the managementdata of

this unit and damage the USB device, resulting in unreadable data.

2 Disconnect the USB device.

3 Close the USB slot cover.

4 Press the [u] switch.

This unit turns off.

English

Additional information

Troubleshooting

! Improper operation is often mistaken for trouble or a malfunction that occurred in the device. If something is wrong with this unit, check the follow-

ing issues, and also access the following Pioneer DJ support site and check [FAQ] for [XDJ-RX2].

pioneerdj.com/support/

Some problems occurs due to the connected components. If the problem cannot be resolved after checking the connected components, ask the

service center or dealer for repairs.

! The unit may not operate properly due to static electricity or other external influences. If this happens, normal operation can be sometimes restored

by removing the power cord after turning the power off, and turning the power back on after inserting the power cord into the power outlet.

Power supply

Problem Check Remedy

The unit does not turn on.

The indicators do not light up.

Is the power cord properly connected? Connect the power cord to an AC outlet. (page 10 )

Is the [u] switch turned on? Turn on the [u] switch.

The power suddenly turns off. Is the auto standby function activated?

(When auto standby is functioning, the

[MASTER REC (WAKE UP)] button is lit in red.)

This unit is shipped with the auto standby function set to on. If you do not

want to use the auto standby function, set [AUTO STANDBY] to [OFF] on the

[UTILITY] screen.

Audio output

Problem Check Remedy

Sound is not output, or sound is too

small.

Are the [DECK 1, LINE1, PHONO1] and [DECK 2,

LINE2, PHONO2] selector switches set to the

proper positions?

Change the input source for the channel using the [DECK 1, LINE1, PHONO1]

and [DECK 2, LINE2, PHONO2] selector switches. (page 13 )

Are the [TRIM] control, channel faders, crossfader

and [MASTER LEVEL] control set to the proper

positions?

Set the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control

to the proper positions. (page 13 )

Sound is distorted. Is the [MASTER LEVEL] control set to the proper

position?

Adjust the [MASTER LEVEL] control so that the master channel level indicator

lights around [0 dB] at the peak level.

Set [ATT.] of [MASTER OUT] on the [UTILITY] screen to [-6 dB] or [-12 dB].

Is the [TRIM] control set to the proper position? Adjust the [TRIM] control to confirm that the channel level indicator lights up in

orange at the highest volume. (page 13 )

Is the level of sound input to the [MIC] terminal set

to an appropriate level?

Set the [MIC1, 2 LEVEL] control to the proper position.

Sound is not output, or the output

sound is distorted or noisy.

Is this unit placed near a TV? Turn the TV off, or place this unit farther away from the TV.

Microphone sound is not output or

the volume is low.

Is the [MIC1, 2 LEVEL] control set to the proper

position?

Set the [MIC1, 2 LEVEL] control to the proper position.

Is the switch on this unit or the microphone

turned off?

Turn the switch on.

Sound is distorted when an analog

player is connected to the [PHONO]

terminals of this unit.

Or, lighting of the channel level

indicator does not change when the

[TRIM] control is turned.

Is an analog player with a built-in phono equalizer

connected to this unit?

When using an analog player with a built-in phono equalizer, connect it to the

[LINE] input terminals. (page 10 )

If the analog player with a built-in phono equalizer has a LINE, PHONO selector

switch, set it to PHONO.

Is an audio interface for computers connected

between the analog player and this unit?

If the audio interface for computers has a line level output, connect it to the

[LINE] input terminals. (page 10 )

If the analog player has a LINE, PHONO selector switch, set it to PHONO.

Display

Problem Check Remedy

Playing address is not displayed in the

remaining time display.

— Playing address may not be displayed for files recorded in VBR. This happens

when it takes time for the unit to detect the length of the track and display the

playing address.

The category is not displayed. Is the rekordbox library information stored on the

USB device?

Use a USB device containing the library information that is exported from

rekordbox to the device..

Is the USB device write-protected? Disable write-protection on the USB device to make it writable.

The scale is not displayed. Is the track over 15 minutes long? The scale is not displayed for tracks whose playing time is over 15 minutes.

The enlarged waveform is not

displayed.

Is the track over 60 minutes long? The enlarged waveform is not displayed for tracks whose playing time is over 60

minutes.

Problem Check Remedy

The unit does not respond when the

screen is touch, or the response is

poor. The detected position is different

from the position actually touched.

Deviation in touch display calibration. Adjust touch screen detection with the [TOUCH DISPLAY CALIBRATION] set-

tings on the [UTILITY] screen.

Functions and operations

Problem Check Remedy

The crossfade function does not work.

Is the [CROSS FADER CURVE (THRU,

, )]

(crossfader curve selector) switch set to [THRU]?

Set the [CROSS FADER CURVE (THRU, , )] (crossfader curve selector)

switch to a position other than [THRU]. (page 13 )

The back cue function does not work. Is a cue point set? Set a cue point.

Beat effect does not work. Is the [LEVEL/DEPTH] control set to the center

position?

Rotate the [LEVEL/DEPTH] control clockwise or counterclockwise.

Is the [TRIM] control set to the proper position? Set the [TRIM] control to the proper position.

Color effect does not work. Is the [SOUND COLOR FX

(DUB ECHO, SWEEP, NOISE, FILTER)] button

pressed?

Press the [SOUND COLOR FX (DUB ECHO, SWEEP, NOISE, FILTER)] button.

Is the [COLOR] control set to the proper position? Set the [COLOR] control to the proper position.

The SYNC function does not work. Has the music file been analyzed? Perform file analysis.

The SYNC function does not work

even when files are analyzed.

Is the beat grid irregular?

Is the beat grid properly tapped?

Set the beat grid properly.

Are the BPMs of the tracks in the two decks too

different?

The SYNC function does work properly if the BPM of the track on the deck for

which the [SYNC/INST.DOUBLES] button is pressed is not within the adjustable

tempo range of the track on the deck for which the [SYNC/INST.DOUBLES]

button is not pressed.

Are you scratching? The SYNC function is disabled while scratching.

Settings are not stored in the memory. Did you turn this unit off directly after changing

the settings?

Turn this unit off 10 seconds after changing the settings.

Make sure to press the [u] switch to turn this unit off.

PRO DJ LINK does not work well. Is the USB (LINK Export) connections driver

software installed?

For a USB connection, install the USB (LINK Export) connections driver

software.

USB devices

Problem Check Remedy

USB device is not recognized. Is the USB device properly connected? Connect the USB device securely (all the way in).

Is the USB device connected via a USB hub? Do not use a USB hub.

Is the USB device supported by this unit? This unit supports USB mass storage devices that can be used as external hard

disks and portable flash memory devices.

Is the file format supported by this unit? Check that the file format of the connected USB device is supported by the unit.

(page 6 )

— Turn the unit off, wait for 1 minute, and then turn the unit on.

It takes time to read USB devices

(flash memory drives and hard discs).

Are many folders and files stored on the USB

device?

It takes time to read a connected USB device if the device contains many folders

and files.

Are files other than music files stored on the USB

device?

It takes time to read a connected USB device if files other than music files are

stored in folders. Do not store files or folders other than music files on the USB

device.

Playback does not start when a track

is loaded from a USB device.

Are the files playable? Check that the file format of the track is supported by the unit.

Is the auto cue function enabled? Press and hold the [TIME MODE(AUTO CUE)] button for approximately 1

second or more, and disable the auto cue function.

Files cannot be played. Is the file copyright-protected (by DRM)? Copyright-protected files cannot be played.

Music files cannot be played. Are the music files damaged? Play music files that are not damaged.

DJ software

Problem Check Remedy

The DJ software on a computer can-

not be operated.

Is the USB cable properly connected? Connect the unit and the computer directly using the USB cable. USB hubs

cannot be used. (page 10 )

Sound of the DJ software is not

properly output.

Are the DJ software settings and the [MIXER

MODE] setting of this unit properly set?

Check the DJ software settings, and then check the settings of this unit on the

[UTILITY] screen and set the proper signal path.

Is the driver software properly set? Set the driver software properly.

Sound is interrupted when using the

DJ software.

Is the latency value of the driver software properly

set?

Set the latency of the driver software to a suitable value.

Set the latency of the DJ software to a suitable value.

English

Error messages

When this unit cannot operate normally, an error code appears on the display. Check the table below and take the measures indicated. If an error code

not shown on the table below is displayed, or if the same error code is displayed again after taking the indicated action, contact your store of purchase.

Error code Error type Description of error Cause and action

E-8302

CANNOT PLAY TRACK

Track data (files) on the storage device cannot

be read correctly.

The track data (file) may be corrupted. dCheck if the track can be

played with another player that supports the same formats as this

unit.

E-8304

E-8305

UNSUPPORTED FILE FORMAT

Music files that cannot be played with this unit

are loaded.

The format is not supported by this unit.dLoad music files in the

supported formats.

Changing the settings

For more information, refer to the Operating Instructions that is avail-

able on the Pioneer DJ support site.

Cleaning the touch display

Do not use organic solvents, acids or alkalis for cleaning the surface

of the touch display. Wipe with a dry soft cloth or a cloth immersed in

neutral detergent and squeezed properly.

Trademarks and registered

trademarks

! Pioneer DJ is a trademark of Pioneer DJ Corporation and is used

under license. rekordbox is a registered trademark or trademark of

Pioneer DJ Corporation.

! Windows is a registered trademark of Microsoft Corporation in the

United States and other countries.

! Adobe and Reader are either registered trademarks or trademarks

of Adobe Systems Incorporated in the United States and/or other

countries.

! “Made for iPod” and “Made for iPhone” mean that an electronic

accessory has been designed to connect specifically to iPod or

iPhone, respectively, and has been certified by the developer to meet

Apple performance standards. Apple is not responsible for the opera-

tion of this device or its compliance with safety and regulatory stan-

dards. Please note that the use of this accessory with iPod or iPhone

may affect wireless performance.

! iPhone, iPod, iPod touch, and Mac are trademarks of Apple Inc.,

registered in the U.S. and other countries.

! Android

™

is a trademark of Google Inc.

! iOS is a trademark on which Cisco holds the trademark right in the

US and certain other countries.

! The names of companies and products mentioned herein are trade-

marks or registered trademarks of their respective owners.

Software license notice

! This software is based in part on the work of the Independent JPEG

Group.

About using MP3 files

This product has been licensed for nonprofit use. This product has not

been licensed for commercial purposes (for profit-making use), such

as broadcasting (terrestrial, satellite, cable or other types of broadcast-

ing), streaming on the Internet, Intranet (a corporate network) or other

types of networks or distributing of electronic information (online digi-

tal music distribution service). You need to acquire the corresponding

licenses for such uses. For details, see http://www.mp3licensing.com.

Cautions on copyrights

rekordbox restricts playback and duplication of copyright-protected

music contents.

! When coded data, etc., for protecting the copyright is embedded in

the music contents, it may not be possible to operate the program

normally.

! When rekordbox detects that coded data, etc., for protecting the

reading, etc.) may stop.

Recordings you have made are for your personal enjoyment and accord-

ing to copyright laws may not be used without the consent of the copy-

right holder.

! Music recorded from CDs, etc., is protected by the copyright laws of

individual countries and by international treaties. It is the full respon-

sibility of the person who has recorded the music to ensure that it is

used legally.

! When handling music downloaded from the Internet, etc., it is the

full responsibility of the person who has downloaded the music to

ensure that it is used in accordance with the contract concluded

with the download site.

Specifications

Power requirements ....................................AC 110 V to 240 V, 50 Hz/60 Hz

Power consumption ............................................................................... 41 W

Power consumption (standby) ............................................................. 0.4 W

Main unit weight ...................................................................................9.1 kg

Max. external dimensions ...

728.2 mm (W) × 108.4 mm (H) × 443.8 mm (D)

Tolerable operating temperature ........................................+5 °C to +35 °C

Tolerable operating humidity ...................... 5 % to 85 % (no condensation)

Audio Section

Sampling rate ....................................................................................44.1 kHz

A/D, D/A converter .................................................................................24-bit

Frequency characteristic

USB, AUX (0 dB/12 dB), MIC1, MIC2 ........................... 20 Hz to 20 kHz

S/N ratio (rated output, A-WEIGHTED)

USB ................................................................................................ 112 dB

LINE ...............................................................................................96 dBu

PHONO............................................................................................ 85 dB

AUX (0 dB) ...................................................................................... 96 dB

AUX (12 dB).................................................................................... 90 dB

MIC .................................................................................................. 81 dB

Total harmonic distortion (20 Hz to 20 kHzBW)

USB ...............................................................................................0.003 %

LINE ..............................................................................................0.005 %

PHONO.........................................................................................0.017 %

Standard input level / Input impedance

LINE ..................................................................................–12 dBu/47 kW

PHONO.............................................................................–52 dBu/47 kW

AUX (0 dB) .......................................................................–12 dBu/47 kW

AUX (12 dB).....................................................................–24 dBu/47 kW

MIC ..................................................................................... –57 dBu/3 kW

Standard output level / Load impedance / Output impedance

MASTER 1 .................................................. +6 dBu/10 kW/390 W or less

MASTER2 ..................................................... +2 dBu/10 kW/1 kW or less

BOOTH ....................................................... +6 dBu/10 kW/470 W or less

PHONES ...........................................................+8 dBu/32 W/1 W or less

Rated output level / Load impedance

MASTER 1 ....................................................................... +24 dBu/10 kW

MASTER 2 ....................................................................... +20 dBu/10 kW

Crosstalk

LINE ................................................................................................. 90 dB

PHONO............................................................................................ 78 dB

Channel equalizer characteristic

HI ......................................................................–∞dBto+6dB(20kHz)

MID .................................................................... –∞dBto+6dB(1kHz)

LOW .................................................................. –∞dBto+6dB(20Hz)

Microphone equalizer characteristic

HI ...................................................................–12 dB to +12 dB (10 kHz)

LOW ..............................................................–12 dB to +12 dB (100 Hz)

Input / Output terminals

PHONO input terminals

RCA pin jacks ..................................................................................2 sets

LINE input terminal

RCA pin jacks ..................................................................................2 sets

MIC input terminal

XLR connector & 1/4” TRS jack ........................................................2 set

AUX input terminal

RCA pin jacks ....................................................................................1 set

MASTER1 output terminal

XLR connector...................................................................................1 set

MASTER2 output terminal

RCA pin jacks ....................................................................................1 set

BOOTH output terminal

1/4” TRS jack .....................................................................................1 set

PHONES output terminal

1/4” stereo phone jack ...................................................................... 1 set

3.5 mm stereo mini jack ...................................................................1 set

USB terminals

A type .............................................................................................. 2 sets

Power supply............................................................... 5 V/1 A or less

B type ................................................................................................. 1 set

— Be sure to use the [MASTER1] terminals for a balanced output.

If they are connected to an unbalanced input (such as RCA) with

an XLR to RCA converter cable (or converter adapter), etc., the

sound quality may be lowered or noise may occur.

Use the [MASTER2] terminals for an unbalanced input (such as

RCA).

— Be sure to use the [BOOTH] terminals for a balanced output. If

they are connected to an unbalanced input, the sound quality

may be lowered or noise may occur.

— The specifications and design of this product are subject to

change without notice.

English

ATTENTION

POUR ÉVITER TOUT RISQUE D’ÉLECTROCUTION, NE

S ENLEVER LE COUVERCLE (NI LE PANNEAU

ARRIÈRE). A

UCUNE PIÈCE RÉPARABLE PAR

’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR.

CONFIER TOUT ENTRETIEN À UN PERSONNEL

ALIFIÉ UNIQUEMENT.

D3-4-2-1-1_B1_Fr

AVER

TISSEMENT

Cet appareil

n’est pas étanche. Pour éviter les risques

d’incendie et de décharge électrique, ne placez près de

lui un récipient rempli d’eau, tel qu’un vase ou un pot de

fleurs, et ne l’exposez pas à des gouttes d’eau, des

éclaboussures, de la pluie ou de l’humidité.

D3-4-2-1-3_A1_Fr

AVER

TISSEMENT

Cet appareil est muni d’une fiche de mise à la terre

(masse) à trois fils. Comme la fiche présente une

troisième broche (de terre), elle ne peut se brancher

que sur une prise de courant, prévue pour une mise à

la terre. Si vous n

’arrivez pas à insérer la fiche dans la

prise de courant, contactez un électricien qualifié pour

faire remplacer la prise par une qui soit mise à la terre.

N’annulez pas la fonction de sécurité que procure cette

fiche de mise à la terre.

D3-4-2-1-6_A1_Fr

AVER

TISSEMENT

our éviter les risques d’incendie, ne placez aucune

flamme nue (telle qu’une bougie allumée) sur

l’appareil.

D3-4-2-1-7a_A1_Fr

Milieu de fonctionnement

mpérature et humidité du milieu de fonctionnement :

De +5 °C à +35 °C (de +41 °F à +95 °F) ; Humidité

relative inférieure à 85 % (orifices de ventilation non

obstrués

)

N’installez pas l’appareil dans un endroit mal ventilé ou

un lieu soumis à une forte humidité ou en plein soleil

(ou à une forte lumière artificielle).

D3-4-2-1-7c*_A1_Fr

PRÉCAUTION DE VENTILATION

Lors de l’installation de l’appareil, veillez à laisser un

espace suffisant autour de ses parois de manière à

améliorer la dissipation de chaleur (au moins 5 cm à

l’arrière et 5 cm de chaque côté).

D3-4-2-1-7d*_A1_Fr

ATTENTION

L’interrupteur de cet appareil ne coupe pas

complètement celui-ci de sa prise secteur. Comme le

cordon d’alimentation fait office de dispositif de

déconnexion du secteur, il devra être débranché au niveau

de la prise secteur pour que l’appareil soit complètement

hors tension. Par conséquent, veillez à installer l’appareil

de telle manière que son cordon d’alimentation puisse être

facilement débranché de la prise secteur en cas

d’accident. Pour éviter tout risque d’incendie, le cordon

d’alimentation sera débranché au niveau de la prise

secteur si vous prévoyez une période prolongée de non

utilisation (par exemple avant un départ en vacances).

D3-4-2-2-2a*_A1_Fr

Lorsque vous utilisez ce produit, vérifiez les

informations concernant la sécurité sous l’appareil.

D3-4-2-2-4_B1_Fr

ATTENTION

Ce produit a été testé dans des conditions de climats

tempéré et tropical. D3-8-2-1-7a_A1_Fr

Le symbole graphique indiqué sur le produit

représente le courant alternatif.

Le symbole graphique indiqué sur le produit

représente le courant continu.

Le symbole graphique indiqué sur le produit

représente un équipement de Classe II. D3-8-2-4_A1_Fr

Appareil d’enregistrement et copyright: Vous ne

pouvez utiliser un appareil d’enregistrement que pour

la copie autorisée et devez vérifier attentivement ce

qui est autorisé en matière de copie dans le pays où

vous effectuez des copies. La copie de matériel

soumis au copyright, comme les films ou la musique,

est interdite sauf en cas d’autorisation exceptionnelle

légale ou d’accord des détenteurs des droits.K018_A1_Fr

Ce produit est destiné à une utilisation domestique

générale. Toute panne due à une utilisation autre qu'à

des fins privées (comme une utilisation à des fins

commerciales dans un restaurant, dans un autocar

ou sur un bateau) et qui nécessite une réparation

sera aux frais du client, même pendant la période de

garantie.

K041_A1_Fr

Si vous souhaitez vous débarrasser de cet appareil, ne le mettez pas à la poubelle avec vos ordures ménagères. Il existe un système de

collecte séparé pour les appareils électroniques usagés, qui doivent être récupérés, traités et recyclés conformément à la législation.

Les habitants des états membres de l’UE, de Suisse et de Nor

vège peuvent retourner gratuitement leurs appareils électroniques usagés aux

centres de collecte agréés ou à un détaillant (si vous rachetez un appareil similaire neuf).

Dans les pays qui ne sont pas mentionnés ci-dessus, veuillez contacter les autorités locales pour savoir comment vous pouvez vo

us débarrasser

de vos appareils.

ous garantirez ainsi que les appareils dont vous vous débarrassez sont correctement récupérés, traités et recyclés et préviendrez de cette façon

les impacts néfastes possibles sur l’environnement et la santé humaine.

K058b_A1_Fr

NOTE IMPORTANTE SUR LE CABLE

D’ALIMENTATION

Tenir le câble d’alimentation par la fiche. Ne pas débrancher la

prise en tirant sur le câble et ne pas toucher le câble avec les

mains mouillées. Cela risque de provoquer un court-circuit ou

un choc électrique. Ne pas poser l’appareil ou un meuble sur

le câble. Ne pas pincer le câble. Ne pas faire de noeud avec le

câble ou l’attacher à d’autres câbles. Les câbles d’alimentation

doivent être posés de façon à ne pas être écrasés. Un câble

abîmé peut provoquer un risque d’incendie ou un choc

électrique. Vérifier le câble d’alimentation de temps en temps.

Contacter le service après-vente le plus proche ou le revendeur

pour un remplacement.

S002*_A1_Fr

La page charge ...

Pioneer XDJ-RX2-W Guide de démarrage rapide

Marque: Pioneer

Modèle: XDJ-RX2-W

Catégorie: Contrôleurs DJ

Taper: Guide de démarrage rapide

Ce manuel convient également à

XDJ-RX2

Télécharger le PDF

rapport

dans d''autres langues

italiano: Pioneer XDJ-RX2-W Guida Rapida
English: Pioneer XDJ-RX2-W Quick start guide
Deutsch: Pioneer XDJ-RX2-W Schnellstartanleitung

Pioneer XDJ-RX2-W Guide de démarrage rapide

Ce manuel convient également à

Pioneer XDJ-RX2-W Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents