Regency Alterra CF780 Le manuel du propriétaire

Marque: Regency

Modèle: Alterra CF780

Catégorie: Poêles

Taper: Le manuel du propriétaire

Ce manuel convient également à

CF780

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

12.23.19

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

MODEL:CF780

www.regency-re.com

CF780 Wood Fireplace

Owners &

Installation Manual

If the information in these instructions is not followed exactly, a ﬁre or explosion may result causing property damage, personal

injury or death. Please read the entire manual before you install and use your appliance. Follow the instructions in the installation

manual for proper use.

919-895a

French Manual: http://bit.ly/30ImJEJ

Manuel en Français: http://bit.ly/30ImJEJ

Thank-you for purchasing a REGENCY FIREPLACE PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product

that are not covered in this manual, please contact the REGENCY DEALER in your area. Keep those REGENCY FIRES burning.

The Regency CF780 wood ﬁreplace ia a decorative appliance that provides aesthetic enjoyment with over 700 square inches of ﬁre viewing area. This ﬁreplace

is deﬁned as a ﬁreplace (primarily for aesthetics) under the 2015 regulations. Failure to follow the manual details can lead to smoke and CO emissions spilling

into the home. It is recommended to have monitors in areas that are expected to generate CO such as heater fuelling areas.

SAFETY NOTE: If this ﬁreplace is not properly installed, a house ﬁre may result. For your safety, follow the installation instructions, contact local building, ﬁre

ofﬁcials, or authority having jurisdiction about restrictions and installation inspection requirements in your area.

“This manual describes the installation and operation of the Regency CF780 ﬁreplace.”

“It is against federal regulation to operate this wood ﬁreplace in a manner inconsistent with operating instructions in this manual, or if any parts are removed.”

“It is against federal regulation to operate this wood ﬁreplace in a manner inconsistent with operating instructions in this manual.”

CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESERVATIVES, METAL FOILS, COAL,

PLASTIC, GARBAGE, SULPHUR OR OIL MAY DAMAGE THE FIREPLACE.

DO NOT BURN:

• Treated wood • Lawn clippings or yard waste • Manure or animal remains

• Coal • Materials containing rubber including tires • Saltwater driftwood or other previously salt water

saturated materials

• Garbage • Materials containing plastic • Unseasoned wood

• Cardboard • Waste petroleum products , paints or paint thinners or asphalt products • Paper products, cardboard, plywood or particle

board. The prohibition against burning these

materials does not prohibit the use of ﬁre starters

made from paper, cardboard, saw dust, wax and

similar substances for the purpose of starting a

ﬁre in a ﬁreplace

• Solvents • Materials containing asbestos

• Colored Paper • Construction or demolition debris

• Trash • Railroad ties

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

The authority having jurisdiction (such as Municipal Building Department, Fire Department, Fire Prevention Bureau, etc.) should be consulted before instal-

lation to determine the need to obtain a permit.

This unit must be connected to either a listed factory built chimney suitable for use with solid fuels and conforming to ULC629 in Canada or UL-103HT in the

United States of America or code approved masonry chimney with ﬂue liner.

CF780 is tested and certiﬁed to ULC S610-M87 (R2018) and UL 127-2011 (R2015).

SAVE THESE INSTRUCTIONS

2 | CF780 Wood Fireplace

copy of the safety label

Safety Label For CF780 .................................................4

installation

Safety Warnings ............................................................5

Creosote: Formation and Removal ................................5

Fuel Wood .....................................................................5

Unpacking your CF780 ..................................................6

Unit Dimensions ............................................................7

Unit Clearances .............................................................8

Mantel clearances .......................................................10

Mantel ..........................................................................10

Installation ...................................................................11

Location .......................................................................11

Ceiling Clearance ........................................................11

CF780 General Installation ..........................................12

Chase Ventilation Grills ................................................13

Flooring Requirements ................................................14

Combustible Floor: Bottom standoff ............................14

Outside Air Duct–Optional ...........................................15

Chimney System Considerations ................................16

Chimney ......................................................................17

Chimney Installation ....................................................18

Offset Chimney ............................................................20

Through the Wall Offset: Gravity Kit must be installed . 20

Chase Enclosure .........................................................21

Gravity Air Feed Kit Option ..........................................22

Framing ........................................................................23

Fireplace Facing ..........................................................23

Covering the Fireplace Facing .....................................23

Installing The Cement Board Panels ...........................24

Spark Guard ................................................................25

CF780 Brick Installation ...............................................26

CF780 Andirons/ Fire dog Installation .........................26

Gas Log Installation .....................................................27

Side shield installation .................................................28

operation

Lighting the CF780 ......................................................29

Controlling Your Fire ....................................................29

Seasoned Wood ..........................................................29

Refueling .....................................................................29

Flue Damper Control ...................................................30

Outside Air Control ......................................................30

Firescreen Operation ...................................................31

Glass Door Operation ..................................................32

Glass Door – open for cleaning ...................................32

maintenance

General Cleaning .........................................................33

Touch up Paint .............................................................33

Glass Cleaning ............................................................33

Chimney Cleaning .......................................................33

Disposal of Ashes ........................................................33

Guillotine System .........................................................33

Brick Cleaning .............................................................33

Vermiculite Smoke Chamber Panel Replacement .......34

Replacing the Top Damper ..........................................34

Firescreen Replacement .............................................35

Glass Replacement (5mm Neoceramic glass) ............36

Latch Replacement ......................................................36

Pulley Service / Replacement......................................37

Annual Maintenance ....................................................38

Parts - Firebox & Body ................................................39

Damper Assembly .......................................................41

Firescreen Assembly ...................................................42

Door Assembly ............................................................43

Vermiculite smoke chamber panels .............................45

Brick Liners ..................................................................45

Warranty .....................................................................48

CF780 Wood Fireplace | 3

table of contents

Safety Decal For CF780

This is a copy of the label that accompanies each Regency Fireplace.

Location of the decal is shown below. We have printed a copy of the

contents here for your review.

NOTE: Regency units are constantly being improved. Check the label on

the unit and if there is a difference, the label on the unit is the correct one.

LISTED FACTORY BUILT FIREPLACE

FPI WOOD FIREPLACE MODEL: CF780/MODÈLE DE FOYER AU BOIS FPI : CF780

DECORATIVE WOOD FIREPLACE / FOYER AU BOIS DÉCORATIF

DO NOT REMOVE THIS LABEL/NE PAS ENLEVER CETTE ÉTIQUETTE

Serial Number/Numéro de série

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS /

DÉGAGEMENTS MINIMAUX PAR RAPPORT AUX MATÉRIAUX COMBUSTIBLES

FPI Fireplace Products International Ltd. Delta, BC, Canada

919-894

MADE IN CANADA

/ FABRIQUÉ AU CANADA

472

CF780 is tested and certified to ULC S610-M87 (R2018) and UL 127-2011 (R2015). Install and use only in accordance with the manufacturer's installation and operating instructions.

Le modèle CF780 est testé et homologué selon les normes ULC S610-M87 (R2018) et UL 127-2011 (R2015). À installer et à utiliser uniquement en suivant les consignes d'installation et d'utilisation du fabricant.

FOR USE WITH SOLID WOOD FUEL ONLY.

Do not overfire the fireplace. Operate only with viewing door fully closed or fully open when optional fire screen is

used. Firebricks must be in place during operation. Combustible materials are not permitted on face of unit. Do

not obstruct combustion air inlet. Do not block required chase ventilation grills. Do not use a fireplace insert or

other products not specified for use with this product. This fireplace has been tested with a gas log set. Replace

glass only with 5 mm neo-ceramic glass.Only use Manufacturer’s Chimneys listed in manual.

Areas of the fireplace incorporating warm or cold air ducts shall be enclosed within the building envelope and in

accordance with the installation instructions. For outside air supply refer to installation instructions.

Part #: 919-894

Colour: black on grey.

Size: 100% (11.8" x 6.3")

Material: P rintable white polyester 7mm

Aug 15/18: Created draft

Apr. 11/19: Updated as per Dave L

Apr. 18/19: Updated as per Dave L

Apr. 24/19: Updated as per Dave L

May 8/19: Updated as per Polytests

June 3/19: Punch out 0.25" hole in lower left where indicated

(Refer to Manual) (se reporter au manuel)

MANUFACTURED

DEC

JAN FEB

MAR APR MAY JUN JUL AUG SEP OCT NOV

CAUTION

UTILISATION DE BOIS COMBUSTIBLE SOLIDE SEULEMENT.

Éviter de faire surchauffer le foyer. Ne faire fonctionner qu'avec les portes complètement fermées ou

complètement ouvertes si un pare-feu en option est utilisé. Les briques réfractaires doivent être bien en

place pendant l'utilisation de l’appareil. Ne jamais laisser de matières combustibles devant l'âtre. Ne pas

obstruer l'entrée d'air comburant. Ne pas obstruer les grilles de ventilation du châssis. Ne pas utiliser avec

des poêles ou foyers encastrables non compatibles ou d'autres produits inappropriés. Cet appareil a été

testé avec un jeu de bûches pour foyer au gaz non ventilé. Remplacer la vitre seulement avec une vitre en

néocéramique de 5 mm. Utiliser uniquement les cheminées du fabricant listées dans le manuel.

Les parties du foyer comprenant des conduits d’air chaud ou froid doivent être placées dans une

enchâssure conformément aux consignes d’installation. Pour une alimentation en air extérieur, se reporter

aux consignes d’installation.

CHAUD LORS DE FONCTIONNEMENT.

NE PAS TOUCHER. GARDER HORS DE PORTÉE DES ENFANTS, À DISTANCE

DES VÊTEMENTS ET MEUBLES. TOUT CONTACT AVEC LA PEAU PEUT

OCCASIONNER DES BRÛLURES.

LIRE LES CONSIGNES CI-DESSUS.

HOT WHILE IN OPERATION

DO NOT TOUCH.

KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.

MAY CAUSE SKIN BURNS,

READ ABOVE INSTRUCTIONS

2021

2022

2023

2019

2020

WARNING: To avoid the risk of damaging fireplace materials and increasing the risk of spreading a fire, DO NOT

USE the fireplace to cook or warm food.

CAUTION: This fireplace requires a large amount of air to operate which may starve other fuel burning appliance

of combustion, ventilation, and dilution air. Do not block chase grill.

Install and use only in accordance with Regency installation instructions. Contact local building or fire officials

about restrictions and installation inspections in your area. Do not connect this unit to a chimney serving another

appliance. For outdoor air supply, refer to installation manual.

ATTENTION

WARNING: Not for use in mobile home.

Fireplace also for use in manufactured homes with solid fuel only.

When burning gas in the fireplace, adjust damper to the fully open position.

Side Wall / Paroi latérale 24 in / 610 mm From edge of top vent / Depuis le rebord de l’évacuation du dessus

Mantel / Manteau 7 in /178 mm From top of vent / Depuis l’évacuation du dessus

Mantel Projection / Prolongement du manteau 12 in /305 mm From face / Depuis la façade

Hearth measurements (USA/CDN) 61-3/8in / 1559mm Wide / de large

20 in / 508 mm Depth / de profondeur

Unit Back and Sides / Dessus, arrière, côtés et bas de l’appareil 0 in / 0 mm To standoff / Vers l’espaceur

Unit Corners /Angles de l’appareil 3 in / 76 mm

Top /Dessus Non-combustible / steel stud only

CAUTION: Gas logs shall be certified for the application. When installed, the chimney shall

be permanently secured in an open position to effectively vent the appliance. The log sets

need to be certified to ANSI Z21.60/CSA 2.26-2017 to be installed in their fireplaces. Do not

operate a gas log set in this fireplace with the chimney removed.

ATTENTION : Les bûches pour foyers au gaz doivent être homologuées pour être

installées dans ce foyer. Une fois installée, la cheminée doit être mise en position ouverte

de manière permanente pour permettre une ventilation adéquate de l’appareil. Les jeux de

bûches doivent être homologués ANSI Z21.60/CSA 2.26-2017 pour être installés dans le

foyer. Ne pas utiliser un jeu de bûches pour foyers au gaz dans cet appareil si la cheminée

n’est pas en place.

À installer et utiliser conformément aux consignes d’installation de Regency. Contacter la Régie du bâtiment

ou le département local incendie pour connaître les restrictions et les consignes d’installation dans votre

municipalité. Ne pas raccorder cet appareil à une cheminée desservant un autre appareil. Pour une

alimentation en air extérieur, se reporter au manuel d'installation.

AVERTISSEMENT : Ne pas utiliser dans une maison mobile.

Ce foyer peut également être utilisé dans une maison industrialisée avec un combustible solide seulement.

Lorsque l'appareil est allumé, régler le registre en position complètement ouverte.

AVERTISSEMENT : Pour éviter d’endommager les matériaux du foyer et diminuer le risque de propagation

d’un feu, NE PAS UTILISER le foyer pour cuisiner ou réchauffer de la nourriture.

ATTENTION : Pour fonctionner correctement, ce foyer nécessite une grande quantité d’air qui pourrait priver d’air

d’autres appareils de chauffage d’air de combustion, de ventilation ou de dilution. Ne pas obstruer la grille du châssis.

Matériau non combustible / montant en acier seulement

CF780 decal location

1. Remove left Screen Trim Panel (See instructions in this manual)

2. Decal will be visible on left side (with trim removed).

3 Remove the rating plate and unroll to view

information.

4. Reverse steps to replace decal.

SERIAL DECAL MUST REMAIN WITH

FIREPLACE AT ALL TIMES.

4 | CF780 Wood Fireplace

safety decal

If this ﬁreplace is not properly installed, a house ﬁre could re-

sult. For your safety, follow the installation directions. Contact

your local authority having jurisdiction (such as municipal

building department or ﬁre department) regarding restrictions

and installation requirements, and the need to obtain a permit.

1. For use with SOLID FUEL ONLY. Do not use any other type of fuel.

2. Burn dry, split, seasoned wood fuel.

3. To avoid glass breakage, DO NOT slam the ﬁreplace door.

4. DO NOT use the ﬁreplace with the door closed if the glass is

cracked or broken. Replace the glass before using the glass door

again.

5. DO NOT ever use gasoline, gasoline-type lantern fuel, kerosene,

charcoal lighter ﬂuid, or similar liquids to start or freshen up a ﬁre.

Keep all such liquids well away from the ﬁreplace while it is in use.

6. DO NOT use logs that are longer than 18".

7. DO NOT overﬁre the ﬁreplace. Burn a maximum of 3 medium

split logs. See complete warning.

8. DO NOT operate the ﬁreplace with both the ﬁre screen and door

open. One of the two should always be closed while having a ﬁre.

9. DO operate the ﬁreplace with the door either fully closed or

fully open. If the door is left partly open, it will increase the burn

rate and permanently damage the ﬁreplace.

10. Keep all combustible materials (furniture, ﬁrewood, etc.) at least

4' away from the front of the ﬁreplace.

11. DO NOT use a ﬁreplace grate or other products not speciﬁed for

use with this ﬁreplace.

12. DO NOT step or put legs of a step ladder on the metal front step

or the hearth threshold.

13. CAUTION: Your warranty will be null & void if making compromises

during installation & operation. Follow the guidelines within this

manual.

14: DO NOT terminate combustion air inlet ducting into attic spaces.

15. CAUTION: This appliance requires the need for room air for com-

bustion. Ensure there is enough ventilation air within the home for

the safe operation of all appliances at the same time. Starving ap-

pliances for air can cause severe back drafting, negative pressure

and nuisance outages. This appliance has an optional outside air

kit which can be purchased. This option is highly recommended

to prevent back drafting, negative pressure and nuisance outages.

Safety Warnings

THE CF780 IS CAPABLE OF BURNING CLEANLY PRIMARILY BECAUSE

IT HAS BEEN ENGINEERED TO QUICKLY BURN VERY HOT. THIS

RESULTS IN A BEAUTIFUL, CLEAN FIRE BUT CAN CAUSE DURABIL-

ITY PROBLEMS IF THE UNIT IS REGULARLY OVERLOADED AND/OR

OPERATED CONTINUOUSLY WITH LARGE WOOD LOADS. THE CF780

IS PRIMARILY A DECORATIVE APPLIANCE AND ACCORDINGLY LESS

EFFICIENT THAN A WOOD BURNING STOVE SO THERE IS NO BENEFIT

TO BURNING LARGE WOOD LOADS.

THE FOLLOWING GUIDELINES WILL ENSURE YOUR FIREPLACE BURNS

BEAUTIFULLY WHILE MAINTAINING ITS DURABILITY:

APPROXIMATE MAXIMUM LOG SIZE: 18" LONG, MAXIMUM LOAD: NO

MORE THAN 3 MEDIUM SPLIT LOGS.

THIS WOOD LOAD IS MORE THAN EFFICIENT TO FILL THE FIREBOX

COMPLETELY WITH FLAMES AND PROVIDE A LARGE AMOUNT OF

RADIANT HEAT.

THE CF780 WILL BURN WITH LARGE HIGH FLAMES REGARDLESS

OF HOW THE WOOD IS PLACED IN THE UNIT. STACKING THE WOOD

TEEPEE-STYLE AGAINST THE BACK OF THE FIREPLACE IS ACCEPTABLE.

IF ANY OF THE FOLLOWING SIGNS APPEAR IN YOUR FIREPLACE THEN

YOU ARE OVERFIRING:

- THE SCREEN CHANNEL IS WARPED

- THE DOOR CHANNEL IS WARPED

WARNING: OVER FIRING THE CF780 WILL CAUSE DURABILITY

PROBLEMS.

Creosote: Formation and Removal

When wood is burned slowly, it produces tar and other organic vapors which

combine with the expelled moisture from the wood to form creosote. The

creosote vapors can condense in the relatively cool chimney of a slow burn-

ing ﬁre. When ignited, this creosote makes an extremely hot ﬁre. The chimney

should be inspected periodically during the heating season to see if a creosote

build-up has occurred. If a signiﬁcant layer of creosote has accumulated (¼”

or more), it should be removed to reduce the risk of chimney ﬁre.

Fuel Wood

We recommend always burning your ﬁreplace with split, dry, seasoned wood

logs. Do not use construction scraps (e.g. 2x4 or plywood scraps) as your

only supply of fuel as you can overheat and seriously damage the ﬁreplace.

WARNING: BURN DRY WOOD ONLY.

DO NOT BURN DRIFTWOOD, TREATED WOOD, COAL,

GARBAGE, OR PLASTIC.

16. Do not use Composite/Bio logs as this can cause extreme temperatures

and cause severe damage within the ﬁreplace. Use of these logs will null

and void your warranty.

17. Do not install in a sleeping room.

18. The structural integrity of the manufactured home ﬂoor, walls,and ceiling

roof must be maintained.

19. DO NOT INSTALL a gas log lighter. This is not permitted for use with this

ﬁreplace.

CF780 Wood Fireplace | 5

installation

Unpacking your CF780

WARNING: THE FIREPLACE IS FRONT HEAVY. MAKE SURE

TO ALWAYS MAINTAIN CONTACT WITH THE FIREPLACE

WHEN MOVING IT TO PREVENT ANY UNDUE TILTING.

1. Remove brackets held in place with 5/16" hex head screws securing unit

to pallet. (4 total)

2. Remove bracket held in place with 2 x 1\4" hex head screws on the exterior

of the unit. NOTE - replace 2 x 1\4" screws when bracket is removed. From

the interior remove 2 x 5/16" screws to completely remove bracket.

3. Remove all part/pieces from the interior of the unit.

4. Remove the ﬂoor standoff that is secured with 4 x 5/16" hex head screws

to the back of appliance.

6 | CF780 Wood Fireplace

installation

Unit Dimensions

* The ﬁreplace bottom standoff is required if the ﬁreplace is installed on a combustible ﬂoor surface or on a combustible ﬂoor structure or on

a combustible raised platform. See section "INSTALLATION: Flooring Requirements" for all the details regarding the requirements to use the

ﬁreplace bottom standoff.

* The chase cavity requires four (4) ventilation grills which are included with the unit. Each grill requires a minimum of 28.5 square inches of open area.

Two (2) at ceiling level and two (2) at ﬂoor level. Grills must be installed and are supplied with the unit.

Optional: If installing grills other than the ones supplied, you must adhere to the minimum open area. For example, you can install two (2) large

grills , one at ceiling level and one at ﬂoor level, but each grill must be 57 square inches of open area.

** Shown with Anchor Plate.

The anchor plate height will vary depending on the speciﬁc chimney manufacturer. See speciﬁc chimney manufactured product catalogue for

complete details.

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.

ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

OUTSIDE

AIR

VIEWING

41"

DOOR OPENING

CF780 Wood Fireplace | 7

installation

Unit Clearances

Refer to K & M on Table 1

(next page)

Refer to I on Table 1

(next page)

Refer to C on Table 1

(next page)

Refer to N on Table 1

(next page)

Refer to L on Table 1

(next page)

Refer to B on Table 1

(next page)

Refer to H on Table 1

(next page)

8 | CF780 Wood Fireplace

installation

TABLE 1 - UNIT CLEARANCES AND SPECIFICATIONS

Distance to combustible material from side, back, and standoffs

0’’ (0mm)

Clearance from Top of unit: No combustible material: only steel stud on Front,

Top edge, and sides

Minimum distance from side wall to the side of the ﬁreplace opening

24” (610mm)

Minimum ceiling clearance: Always take measurement from the lowest point on

the ﬁreplace,; Including Base–Radiation Shield

- When the bottom standoff is installed, measure from the base of the bottom

standoff to the ceiling

(refer to the “INSTALLATION: Flooring Requirements” section for details)

8’ (2.44m)

Minimum chimney height: minimum total chimney height from ﬁreplace top to

below the chimney rain cap

12' (3.66m)

Maximum chimney height: maximum total chimney height from ﬁreplace top to

below the chimney rain cap

60' (18.3m)

Maximum chimney height supported by the ﬁreplace

15' (4.57m)

Minimum depth of non-combustible hearth extension: from the front of the ﬁreplace

(refer to the “INSTALLATION: Hearth Extension” section for details)

20" (508mm)

Minimum width of non-combustible hearth extension: total width, must be cen-

tered on the ﬁrebox opening (refer to the “INSTALLATION: Hearth Extension”

section for details)

61-3/8" (1559mm)

Minimum width of the spark guard

61-3/8" (1559mm)

Maximum mantel shelf depth (see Table 2 for other mantel sizes)

12" (305mm)

Minimum height of a combustible mantel shelf above the top of the ﬁreplace

opening (to the bottom of the combustible mantel) (refer to the “INSTALLATION:

Mantel” section for details)

See Table 2

Maximum mantel leg depth (see Table 3 for other mantel leg sizes)

12" (305mm)

Minimum distance between each combustible mantel leg and the ﬁreplace open-

ing (refer to the “INSTALLATION: Mantel” section for details)

See Table 3

Note: For 45°corner installs: 3" clearance is required from back corners of unit.

A=3" A=3"

CF780 Wood Fireplace | 9

installation

TABLE 2 - COMBUSTIBLE MANTEL CLEARANCES

0" to 6" 7"

7" to 12" 12"

A combustible mantel shelf MUST NOT be installed less than 7" above the top

of the ﬁreplace opening. A combustible mantel shelf MUST NOT be deeper

than 12".

For combustible mantel shelf depths between 6" and 12", simply install the

mantel shelf at a distance above the ﬁreplace opening corresponding to the

mantel shelf depth.

If the combustible mantel shelf varies in depth, it has to be installed so that its

thickest part is not installed lower than the corresponding minimum installation

height. Also, the thinnest point of the mantel shelf must not be installed lower

than the minimum installation height corresponding to its depth.

Refer to the “INSTALLATION: Mantel” section.

If the combustible mantel leg varies in depth, it has to be installed so that its

thickest part is not installed closer than the corresponding minimum installa-

tion distance. Also, the thinnest point of the mantel leg must not be installed

closer than the minimum installation distance corresponding to its depth.

Refer to the “INSTALLATION: Mantel” section.

TABLE 3 - MANTEL LEG CLEARANCES

Maximum Mantel Leg Depth

Minimum Installation

Height

0" to 3" 6"

12" 12"

A combustible mantel leg MUST NOT be installed less than 6" from either

side of the ﬁreplace opening. A combustible mantel leg MUST NOT be deeper

than 12".

For combustible mantel leg depths between 6" and 12", you can calculate the

minimum installation distance between the two mantel legs given as follows:

Masonry and other non-combustible mantels (shelf and posts) can be placed

anywhere around the ﬁreplace opening.

The only combustible material accepted on the facing of the ﬁreplace is for a

mantel (shelf and posts).

If you need to attach the mantel to the front of the ﬁreplace refer to page 23 to

see where screws are permitted on the front of the ﬁreplace facing.

Mantel

Mantel clearances

31-9/16"

0-6"

to bottom of

unit opening

CF780

49-5/8"

0-3"

10 | CF780 Wood Fireplace

installation

Installation

Check with your local authority having jurisdiction (such as municipal

building department, ﬁre department, ﬁre prevention bureau, etc.)

regarding restrictions and installation requirements, and the need to

obtain a permit.

WARNING: IF THIS FIREPLACE IS NOT PROPERLY

INSTALLED, A HOUSE FIRE CAN RESULT. FOR YOUR

SAFETY, FOLLOW THE INSTALLATION INSTRUCTIONS

AND CLEARANCES. DO NOT PACK REQUIRED AIR

SPACES WITH INSULATION OR OTHER MATERIALS.

Location

The CF780 must be installed within the vapor barrier of the home. It

cannot be installed outside, or on a three season porch.

Your CF780 ﬁreplace may be installed in different ways (see Diagram

of framing examples).

Speciﬁcations of the ﬁreplace along with clearances are shown in

Diagram 1, Diagram 2, Table 1, Table 2, and Table 3. We recommend

that you take the time to plan your entire installation (ﬁreplace and

chimney) before beginning the actual installation (refer to General

Installation next page).

1. Note the location of roof and ﬂoor joists. Choose a location cutting

them if possible.

2. Do not build shelves or cupboards in the area above the ﬁreplace.

This space must be kept empty.

3. We recommend the chimney be installed in the interior of the build-

ing as it will provide better performance than an exterior chimney.

In areas with continuous temperatures below 32°F (0°C) the use

of an exterior chimney may result in operating problems such as

poor draft and excessive condensation of combustion products. If

you do install an exterior chimney we recommend that you install it

within an insulated enclosure (see Installation: Chase Enclosure).

WARNING: In order to avoid the possibility of exposed insulation or

the vapor barrier coming in contact with the appliance body, it is

recommended that the walls of the enclosure be ﬁnished off with

drywall as you would ﬁnish any other interior/insulated wall of a

home. This will ensure that clearance to combustibles is maintained

within the cavity. Objects placed in front of the appliance but not

limited to such as sofa's, furniture,etc., must be kept a minimum of

48" (1219 mm) away from the front face of the appliance.

Ceiling Clearance

The ceiling clearance varies depending if the ﬁreplace is installed on

a non-combustible ﬂoor or on a combustible ﬂoor.

On a non-combustible ﬂoor with a non-combustible ﬂoor structure,

the ceiling clearance is the distance from the base of the ﬁreplace to

the ceiling.

On a combustible ﬂoor or on a combustible ﬂoor structure, you need

to install the ﬁreplace on the ﬁreplace bottom standoff thus the ceiling

clearance is the distance from the base of the ﬁreplace bottom standoff

to the ceiling.

For ceiling clearance requirements refer to Table 1 (D).

Framing Examples

Steel Studs

Wood Studs

Wood Stud

96"

Front face & header –build with steel studs and non-combustible board. Plan out

and frame ventilation grills. Finish with materials such as stone or tile.

Minimum chase height is 96"

Note: Wood studs may be used outside of where the steel studs are located.

CF780 Wood Fireplace | 11

installation

General Installation

CF780 General Installation

Rain Cap

Storm Collar

Flashing

Roof top radiation shield

Radiation shield with

Storm Collar in the Attic

8" Insulated Chimney

Radiation Shield

8" Anchor Plate from

chimney manufacturer

Ceiling

Hearth Extension

Ventilation Grills

(Two each side required)

Ceiling level: 3" down

Floor level: 3" up from ﬁn-

ished ﬂoor

Optional Outside Air

12 | CF780 Wood Fireplace

installation

Chase Ventilation Grills

The unit is supplied with four (4) ventilation grills for the chase/ﬁreplace cavity. Each grill must have a minimum of

28.5 square inches of open area. The total minimum open area of chase ventilation is 114 square inches with a

minimum of 57 square inches at the ceiling level and 57 square inches at the ﬂoor level. The grills must be installed

so there is 57 square inches of open area at the ceiling level and 57 squares inches of open area at the ﬂoor level.

Alternatively, two larger grills (not supplied) may be installed but must be a minimum of 57 square inches of open

area each.

Do not remove cover chase grills. These are mandatory and required to ensure there is no overheating

of the chase cavity.

Chase ventilation grills are required for all installs. The ventilation grills must be installed within the home to prevent

moisture buildup with in the chase/ﬁreplace cavity.

Note: The ventilation grills must be located within the conﬁnes of the framed chase.

Must be located

between 3"-12"

of chase enclosure

*Must be located

between 3"-12"

of chase enclosure

*See location note

CF780 Wood Fireplace | 13

installation

Flooring Requirements

Before installing your CF780, make sure the ﬂoor surface and ﬂoor structure

can sustain the weight of the complete ﬁreplace and whatever ﬁnishing material

you will use to cover the facing of your ﬁreplace.

You can install your ﬁreplace at the ﬂoor level or build a platform to elevate

it to the desired height. Again, make sure the platform is level and built to

sustain the weight of the ﬁreplace and ﬁnishing material you will use to ﬁnish

the facing of your ﬁreplace.

Note: If the appliance has 3-1/2" of non combustible material under the full

width and depth of the ﬁreplace, the bottom standoff is not required.

Combustible Floor: Bottom standoff

If the CF780 is installed on any type of combustible ﬂoor surface or structure,

you MUST install the ﬁreplace onto the ﬁreplace bottom standoff provided with

the ﬁreplace. You must also reinforce the sub-ﬂoor to help spread the load from

the legs of the bottom standoff throughout the ﬂoor structure to prevent sagging.

2. Determine location , level the unit, and secure to the ﬂoor.

1. Assemble the bottom standoff shield to both supports (see Diagrams below)

using eight large self-tapping screws.

0.500

Diagram 2 - Positioning the Fireplace Bottom Standoff

Diagram 1 - Installing the Fireplace Bottom Standoff

3. Position the bottom standoff on the ﬂoor along with the spark guard (refer

to the “Hearth Extension” section for additional information). Use Diagram 2

to help in properly locating the bottom standoff and the spark guard based

on the silhouette of the entire ﬁreplace which includes the back and angled

sides’ standoffs.

tooltip

Diagram 3

Anti-Tip Stability Bracket Installation

4. Using at least 1-½" wood screws (not provided), solidly attach both left

and right sides of bottom standoff to the ﬂoor, as well as the front and back

of the inner sides, as shown in Diagram 3. If possible, attach the bottom

standoff to the ﬂoor joists below using 3" wood screws (not provided).

5. Install the ﬁreplace onto the ﬁreplace bottom standoff making sure that

the base of the ﬁreplace is aligned with the bottom standoff as shown in

Diagrams 1 and 2.

tooltip

14 | CF780 Wood Fireplace

installation

Outside Air Duct–Optional (Part# 096-915)

After the ﬁreplace is correctly positioned, connect the outside air inlet of the ﬁreplace to the outside (see adjacent Diagram).

The air inlet MUST be at least 5' below the top of the chimney ﬂue and must never terminate in attic spaces.

A 4" diameter duct can be used if the total duct run is less than 20'. For longer runs, use 5" diameter duct.

1. Find a convenient location for the combustion air duct and outside air inlet. The outside air inlet can be above or below

ﬂoor level.

2. Make a 4 ¼” (5 ¼” if using a 5” diameter duct) hole in the outside wall of the house. Push the outside air hood in from

the outside. Seal the joint between the air hood and the outside wall with an appropriate sealant.

3. Place the insulated ﬂexible duct over the round sleeve on the outside air hood. At both ends, carefully pull back the

insulation and plastic cover, exposing the ﬂexible duct. Then at each end, attach the duct with supplied metal screws

to the air hood and to the ﬁreplace connecting sleeve. Carefully push the insulation and cover back over the duct. Tape

the plastic cover in place with 2” aluminum duct tape (not supplied).

Outside Air Connection and Installation

Example

CAUTION: WHEN RUNNING THE DUCT AROUND

CORNERS, AVOID CRUSHING THE DUCT WHICH CAN

RESTRICT THE COMBUSTION AIRFLOW.

Insulated

Flexible

Air Duct

2" Aluminum

Duct Tape

Outside Air Inlet:

either above or below

the level of the ﬁreplace

Ducting -

4" diameter x 4' length

CF780 Wood Fireplace | 15

installation

Chimney System Considerations

Regency’s CF780 Fireplace is to be installed with one of the following Chimney Systems only. Chimney systems only 8" (203mm) diameter are to be used

that comply to ULCS 629 for CDN and UL103HT for USA.

The use of only one of these systems is permitted when installing the ﬁreplace. Do not alter or mix parts from other systems as this may cause a potential

hazard and void Regency’s limited warranty.

DuraVent DuraTech 1" Solid Pack 8" (20 cm)

DuraVent DuraTech Canada (DTC) 1" Solid Pack 8" (20 cm)

DuraVent DuraPlus HTC 2" Solid Pack 8" (20 cm)

DuraVent DuraTech Premium 2" Solid Pack 8" (20 cm)

DuraVent (USA only) DuraPlus AC Triple Wall 8" (20 cm)

ICC Excel 2100 1" Solid Pack 8" (20 cm)

Metal Fab Temp Guard 1" Solid Pack 8" (20 cm)

Olympia Chimney Champion Chimney System 1" Solid Pack 8" (20 cm)

Olympia Chimney / SBI

Venting Division

Ventis 1" Solid Pack 8" (20 cm)

SBI Venting Division Nexvent 1" Solid Pack 8" (20 cm)

Security Chimney ASHT+ 1" Solid Pack 8" (20 cm)

Security Chimney S-2100 + 2" Solid Pack 8" (20 cm)

Selkirk Ultra-Temp (UT) 1" Solid Pack 8" (20 cm)

Selkirk Sure-Temp (ST) 1” Solid Pack 8” (20 cm)

Selkirk Hart & Cooley (TLC) 1” Solid Pack 8” (20 cm)

Selkirk UltimateOne 1” Solid Pack 8” (20 cm)

Selkirk CF Sentinel (CF) 2” Solid Pack 8” (20 cm)

Selkirk Super Pro 2100 (ALT) 2” Solid Pack 8” (20 cm)

Selkirk Super Vent 2100 (JM) 2” Solid Pack 8” (20 cm)

Selkirk (USA Only) Super Vent (JSC) 1” Solid Pack 8” (20 cm)

Metal Fab (USA only) Metal Fab Air Cool 8" (20cm)

Note: Anchor plates are provided by the chimney manufacturer and are required for all installations for all above chimney listings.

16 | CF780 Wood Fireplace

installation

Chimney

This ﬁreplace is certiﬁed for use with 8" chimney only. Please refer to Table 1 (E-F) (in this manual) for the minimum and maximum chimney heights permitted

with the CF780.

TABLE 4 - MINIMUM RECOMMENDED FLUE HEIGHTS IN FEET FROM THE TOP OF THE FIREPLACE

Elevation (ft) 0 2 x 15° 4 x 15° 2 x 30° 4 x 30° 2 x 45° ** 4 x 45° **

0 - 1000 12’ 13’ 14’ 15’ 18’ 16’ 20’

1000 - 2000 12’6’’ 13’6’’ 14’6’’ 15’6’’ 19’ 16’6’’ 20’6’’

2000 - 3000 13’ 14’ 15’ 16’ 29’6’’ 17’ 21’6’’

3000 - 4000 13’6’’ 14’6’’ 15’6’’ 17’ 20’ 18’ 22’6’’

4000 - 5000 14’ 15’ 16’ 17’6’’ 21’ 18’6’’ 23’

5000 - 6000 14’6’’ 15’6’’ 17’ 18’ 21’6’’ 19’ 24’

6000 - 7000 15’ 16’ 17’6’’ 18’6’’ 22’6’’ 20’ 25’

7000 - 8000 15’6’’ 16’6’’ 18’ 19’ 23’ 20’6’’ 25’6’’

8000 - 9000 16’ 17’ 18’6’’ 20’ 24’ 21’ 26’6’’

9000 - 10000 16’6’’ 17’6’’ 19’ 20’6’’ 24’6’’ 22’ 27’

We recommend that the minimum height be increased by approximately 1' for every 2000' elevation above sea level. Every 15°, 30° or 45° elbow also

increases the minimum height by 1'. For example, if you are living 6000' above sea level, your chimney should terminate at least 15’ from the top of the

ﬁreplace (12’ + 3’ for the 6000’). See Table 4 for more precise recommended ﬂue heights.

** 45 degree elbows are not permitted for use in the U.S.A.

CF780 Wood Fireplace | 17

installation

WARNING: THE CLEARANCE BETWEEN THE CHIMNEY

AND COMBUSTIBLE MATERIAL MUST BE 2’’ OR MORE.

DO NOT FILL THIS AREA WITH INSULATION.

1. Cut and frame the required holes in the ﬂoor(s), ceiling(s) and roof

where the chimney will pass through. The rough opening in the fram-

ing is 18" square (the opening can be slightly bigger, up to 18 ½", but

NEVER smaller).

2. At each ﬂoor where the chimney passes through, you must install a

radiation shield.

a. Start by locating the shorter circular shield and remove the screws

that attach the ring at one end. Keep the ring and all the screws; you

will need to reinstall it later.

b. Locate the ﬁrestop plate and bend the two tabs downwards so they

extend through the circular cutout. Insert the shorter circular shield

through the ﬁrestop plate. It will extend below the ﬁrestop plate and

rest on the bent end.

c. Install this portion of the radiation shield from below into the framed

opening.

d. Install some chimney lengths so that the chimney extends at least

24” above the ﬂoor structure.

3. At the attic level, install a radiation shield as explained above and a

storm collar.

The chimney must extend at least 3' above its point of contact with the

roof and at least 2’ higher than any wall, roof, or building within 10’ of

it. If the chimney is higher than 5’ above the roof, it must be secured

using a roof brace.

For manufactured homes the roof thimble assembly shall extend com-

pletely through the ceiling/roof cavity of the manufactured home to the

outer most plane of the roof.

4. At the roof, install a roof top shield The two support brackets are adjust-

able depending on the ﬂashing used and the roof pitch. To determine the

position of the two support brackets, ﬁnd the roof pitch in Table 5. Then

identify the ﬂashing that will be used to be able to ﬁnd the associated

installation number. Both support brackets need to be installed in the

holes of the roof top radiation shield corresponding to the installation

number.

5. Put the roof ﬂashing into place. Seal the joint between the roof and the

ﬂashing with rooﬁng tar. For sloping roofs, place the ﬂashing under the

upper shingles and on top of the lower shingles. Secure the ﬂashing to

the roof with rooﬁng nails or screws. If using a ventilated roof ﬂashing,

ensure not to caulk or seal the ventilation openings in the manu-

facture's ﬂashing. Install in the proper orientation as per chimney

manufacturers instructions.

6. Place the storm collar over the chimney and ﬂashing. Seal it around the

chimney with silicone sealer (DO NOT use rooﬁng tar).

7. Fit the rain cap on the chimney. Secure it tightly in place with the screws

provided.

Chimney Installation

Read the all chimney installation manuals to review requirements for supports, bracing, anchors, etc. They can be found under your chimney selection.

Refer to Table 1 (G) for the maximum chimney height that can be supported by the top of the ﬁreplace.

18 | CF780 Wood Fireplace

installation



----













 









 

























 

 









Figure 13 General Chimney Installation

CANADA ONLY:







•



          

            

   

        

      



              

      

            

             

          



General Chimney Installation

Note: Nailing strips differ than shown in diagram

Anchor plate

NOTE: It is recommended to enclose chimney with

proper clearances with blown-in insulation.

Chimney installation

CF780 Wood Fireplace | 19

installation

An elbow may be installed directly on top of the ﬁreplace if required. Use

the offset option if you need to clear a joist or pass around a cupboard. See

following Diagrams for example.

- In USA: 30° Maximum - In Canada: 45° Maximum

The maximum number of elbows per system is four, resulting in two offsets

and returns.

Install the ﬁreplace and chimney as described earlier. When you require an

elbow, proceed as follows:

1. Install the elbow. Turn it in the desired direction, and fasten it to the other

section with 4 metal screws at the joints.

2. Install enough lengths to obtain the desired offset. Secure each joint with

4 metal screws.

3. Use another elbow to return the chimney to the vertical direction. Again

fasten it to the other section with 4 metal screws at the joints.

4. Install a roof support, a wall support, or an offset support above each

offset to support the weight of the chimney (elbows are not designed to

support the chimney above an offset).

NOTE: 'Through the wall offset' installation requires installa-

tion of the gravity kit along with chase ventilation grills.

Failure to do so could result in severe overheating of the ﬁreplace

chase cavity.

�













































 







Figure 14 Offset

Installation Example

Chimney

Figure 15 Offset Chimney Through

a Wall Example

Table 6 Through the Wall Installation Dimensions

Offset Through the

Wall Wall

 







 



 

  

























 













  

 





 



 

  

  





 

             

                 

      

Offset Chimney Installation Example

Note: Nailing strips differ than shown in diagram

Offset Chimney Through a Wall Example

You can also go through a wall at an angle starting directly at the ﬁreplace as

depicted in Diagram below. An angled wall insulated radiation shield must be

used wherever the chimney passes through an exterior wall.

Make sure to have enough ceiling height for your installation. If the ceiling height

is too low for the planned installation you may want to consider installing the

ﬁreplace in an outside chase.

Refer to the angled wall insulated radiation shield installation sheets for detailed

installation instructions.

Through the Wall Offset:

Gravity Kit must be installed

�

翿�

Radiation Shield

Use Oﬀset Support

or Roof Support

Refer to

"Canada

Only''

section if

installed in Canada

Radiation

Shield

Flashing

with

Storm Collar

and Roof Top

Radiation Shield

Insulation

Oﬀset, Roof

or Wall Support

Ceiling Clearance

see Table 6

Figure 14 Oﬀset

Installation Example

Chimney

Figure 15 Oﬀset Chimney Through

a Wall Example

Table 6 Through the Wall Installation Dimensions

Oﬀset Through the

Wall Wall

US and Canada

Canada Only

Minimum required

12'3"

10' 6

11' 10"

if not using the

10' 1"

if not using the

ceiling heightA

bottom standoﬀ

Height of the

9¼

center of the hole

if not using the

8' 3½"

if not using the

in the wallA

bottom standoﬀ

Minimum height of

53" 35½"

the hole

Position of the hole

Centered on the chimney coupling of the ﬁreplace or on the

ﬁreplace casinq (not on the quillotine bay at the front)

Minimum width of

18"

the hole

A These heights assumed that the ﬁrst elbow is directly on the ﬁreplace as depicted in

Figure 15. If this is not the case, these heights have to be increase by the length of

chimney installed on the ﬁreplace before the ﬁrst elbow.

Gravity Kit

Anchor plate

1 (D)

Offset Chimney

20 | CF780 Wood Fireplace

installation

La page est en cours de chargement...

Regency Alterra CF780 Le manuel du propriétaire

Marque: Regency

Modèle: Alterra CF780

Catégorie: Poêles

Taper: Le manuel du propriétaire

Ce manuel convient également à

CF780

Télécharger le PDF

rapport

dans d''autres langues

English: Regency Alterra CF780 Owner's manual

Regency Alterra CF780 Le manuel du propriétaire

Ce manuel convient également à

Regency Alterra CF780 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents