Regency Fireplace Products Horizon HZI540EB Le manuel du propriétaire

Marque: Regency Fireplace Products

Modèle: Horizon HZI540EB

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

Liberty L540EB

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-252a

MODELS: L540E-NG2 Natural Gas L540E-LP2 Propane

HZI540E-NG2 Natural Gas HZI540E-LP2 Propane

WARNING:

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. Refer to

this manual. For assistance or additional information consult

an authorized installer, service agency or the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other ﬂammable vapours and

liquids in the vicinity of this or any other appliance.

Installation and service must be performed by an authorized

installer, service agency or the gas supplier.

FOR YOUR SAFETY

What to do if you smell gas:

Do not try to light any appliance

Do not touch any electrical switch:

do not use any phone in your

building.

Immediately call your gas supplier

from a neighbour's phone. Follow

the gas supplier's instructions.

If you cannot reach your gas

supplier, call the ﬁre department.

L540E / HZI540E Gas Insert

10/16/14

Owners &

Installation Manual

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

www.regency-re.com

L540E-2 / HZI540E-2 Direct Vent Gas Insert

TO THE NEW OWNER

Congratulations! You are the owner of a state-of-the-art Gas Insert by Regency.

The Regency Gas Insert Series of hand crafted appliances has been designed to provide you with all the

warmth and charm of a replace, at the ick of a switch. The models L540E / HZI540E of this series have been

approved by Warnock Hersey for both safety and efciency. As it also bears our own mark, it promises to

provide you with economy, comfort and security for many trouble free years to follow.

Please take a moment now to acquaint yourself with these instructions and the many features of your

Regency Fireplace.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

DIMENSIONS

UNIT DIMENSIONS

588.72

798.02

465.81

715.47

257.80

600.08

57.40

425.13

626.91

352.93

12"

305.19

856.58

1011.43

1155.45

768.25

L540E-2 / HZI540E-2 Direct Vent Gas Insert

DIMENSIONS

Dimensions w/Full Screen Doors

Dimensions w/4 sided Faceplate

Dimensions w/Oversized Faceplate

45-1/2"

1155.45

23"

585.62

785.34

929.36

33"

838mm

695mm

46"

1168mm

1011mm

495.30

1155.70

688.98

768.35

530.23

349.25

L540E-2 / HZI540E-2 Direct Vent Gas Insert

TABLE OF CONTENTS

3 sided low prole faceplate installation ......................33

4 sided low prole faceplate installation ......................34

Oversize faceplate installation ..................................... 35

Regular faceplate installation ......................................36

Optional Hearth Trim installation .................................37

Optional screen installation .........................................38

Optional full screen door installation............................39

OPERATING INSTRUCTIONS

Operating Instructions ................................................40

Lighting Procedure ......................................................40

Shutdown Procedure ...................................................40

First Fire ......................................................................40

Automatic Convection Fan Operation.........................40

Normal Operating Sounds Of Gas Appliances ............41

Copy Of Lighting Instruction Plate ...............................41

MAINTENANCE

Maintenance Instructions............................................42

Door Glass ..................................................................42

Pilot Adjustment ........................................................... 43

General Vent Maintenance ..........................................43

Log Replacement ........................................................43

Glass Gasket ...............................................................43

Glass crystal burner removal / installation (HZI540E) .44

Glass Burner Removal ................................................44

Glass Burner install .....................................................44

L540E ceramic burner Removal / installation ..............45

Fan maintenance - with GTMF remote control ............46

Valve replacement .......................................................47

PARTS LIST

Main Assembly ............................................................49

Low prole faceplate ...................................................51

WARRANTY

Warranty ......................................................................55

DIMENSIONS

Unit dimensions .............................................................3

SAFETY LABEL

Copy of the Safety Label ...............................................5

INSTALLATION

MA Code - CO Detector.................................................8

Important Message ...................................................... 9

Before You Start ............................................................9

Important Message .................................................... 10

For Your Safety ............................................................ 10

Specications ..............................................................10

Gas Pressure Testing ..................................................10

Installation Into A Solid Fuel Burning Fireplace Or

Factory Built Fireplace ................................................. 10

Before You Start ..........................................................10

Installation Checklist .................................................... 11

Materials Required ...................................................... 11

Minimum Fireplace

Dimensions .................................................................. 11

Minimum Clearances to combustibles ......................... 12

Gas Connection ........................................................... 13

Venting.........................................................................13

Flue / vent installation .................................................. 14

LeveLing leg adjustment..............................................15

Air shutter Adjustment .................................................16

High Elevation .............................................................17

Gas Line Installation ....................................................17

Gas Pipe Pressure Testing ..........................................17

885 S.I.T. Valve Description .........................................17

Conversion from NG to LP ........................................18

Proame remote system GTMF with fan (L540E /

HZI540E) ....................................................................20

Wiring diagram ............................................................20

Optional wall thermostat installation ............................21

Glass crystal / optional stone installation.....................22

Optional Pebbles / Glass crystal Installation ...............22

HZ540E optional log set installation ...........................24

L540E log set installation ............................................26

Standing pilot and heat exchange return ..................... 29

Brick panel installation ................................................. 30

Enamel panel installation.............................................31

Glass door removal / installation .................................32

L540E-2 / HZI540E-2 Direct Vent Gas Insert

SAFETY LABEL

This is a copy of the labels that accompany each L540E Gas Insert. We

have printed a copy of the contents here for your review.

NOTE: Regency units are constantly being improved. Check the

label on the unit and if there is a difference, the label on the unit is

the correct one.

NATURAL GAS FIREPLACE INSERT:

Factory Equipped For Altitude 0-4500ft. (0-1370m)

Min. supply pressure 5“ WC (1.25 kpa)

Low Setting Man. pressure 1.6" WC (0.41 kpa)

Max. Manifold pressure 3.5" WC (0.87 kpa)

Orifice size #32 DMS

Minimum input 25,000 Btu/h (7.33 kW)

Maximum input 38,000 Btu/h (11.14 kW)

Min. supply pressure 11"WC (2.73 kpa)

Low Setting Man. pressure 6.4" WC (1.59 kpa)

Max. Manifold pressure 10" WC (2.48 kpa)

Orifice size #51 DMS

Minimum input 30,000 Btu/h (8.79 kW)

Maximum input 38,000 Btu/h (11.14 kW)

PROPANE GAS FIREPLACE INSERT:

Factory Equipped For Altitude 0-4500ft. (0-1370m)

MODEL L540E-NG2

MODEL L540E-LP2

Model/Modele:

L540E-NG2

919-253

DO NOT REMOVE THIS LABEL /

NE PAS ENLEVER CETTE ETIQUETTE

Serial No. / No de serie

401

Duplicate Serial number

Listed:

Certified for/Certifi e pour: CANADA and U.S.A.

VENTED GAS FIREPLACE HEATER

Tested to:

FOYER AU GAZ À ÉVACUATION

CAN/CGA-2.17-M91(R2009)

ANSI Z21.88-2009/CSA 2.33-2009

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS. /

NE PAS UTILISER AVEC DUCOMBUSTIBLE SOLIDE.

FOYERAU

GAZ À ÉVACUATION -

Model/Modele:

-LP2

L540E

ÉÉQUIP A L'UISINE POUR GAZ PROPANE

MODELL540E-LP2

ÉÉQUIP A L'UISINE POUR GAZ NATURAL

MODELL540E-NG2

Pression d'allimentation minimum

Pression la tubulure d' chappement basse

Pression la tubulure d' chappement lev e

Dimensions de l'orifice

D bit Calorifique minimum

D bit Calorifique maximum

ééé

Pression d'allimentation minimum

Pression la tubulure d' chappement basse

Pression la tubulure d' chappement lev e

Dimensions de l'orifice

D bit Calorifique minimum

D bit Calorifique maximum

ééé

Mantel Clearances

FPI Fireplace Products International Ltd.,

Delta BC, CANADA

MADE IN CANADA /FABRIQUE AU CANADA

Minimum Clearances to Combustibles

from Insert

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and

Propane Installation Code, CSA B149.1.

This appliance is onlyfor use with thetype of gas indicated onthe rating plate.

This appliance is notconvertible for use withother gases unless a certifiedkit is used.

This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured

(mobile) home where notprohibited by local codes.See owner's manual for details

WARNING. This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original

parts have been replaced,and the fireplace re-approvedby the authority having jurisdiction.

Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel

Gas Code ou CSA-B149.1en vigueur.

AVERTISSEMENT :Ce foyer a été converti pour utilisation avec un foyer au gaz encastrable et ne peut être utiliser pour brûler du bois ou d'autres

combustibles solides à moinsque toutes les piècesd'origine aient été remplacées et que le foyer aitété approuvé de nouveau par l'autorité compétente.

This vented gas fireplaceheater is not for use with air filters. Ne pas utiliser defiltre à air avecce foyer au gaz àévacuation.

Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison

préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de

renseignements. Cet appareil nepeut pas être utiliséavec d'autres gaz sauf siune trousse de conversioncertifiée est fournie.

Cet appareil n'est pasconvertible pour une utilisationavec d'autres gaz, sauf siun kit certifié estutilisé.

Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison

préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de

renseignements.

Electrical supply / Électrique 115VAC, 2.5 A, 60Hz, Less than 10A Fan Part # 911-071

Side wall A12” (305mm)

Ceiling B60” (1524mm)

12" Mantel Max. C 24” (610mm)

Min. Alcove Width K 56" (1422mm)

Max. Alcove Depth L36” (914mm)

*Min. Hearth Width D14” (356mm)

*Min. Hearth Length E44” (1016mm)

Max. Mantle Depth G 12" (305mm)

* See installation manual for hearth requirements.

*If unit is raised 6" from the floor - no hearth

required.

@ 24" form fireplace opening

4001172

For the State of Massachusetts, installation and repair must be done by a plumber or gasﬁtter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, ﬂexible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with

battery back up in the same room where the gas appliance is installed.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

SAFETY LABEL

This is a copy of the labels that accompany each HZI540E Gas Insert.

We have printed a copy of the contents here for your review.

NOTE: Regency units are constantly being improved. Check the

label on the unit and if there is a difference, the label on the unit is

the correct one.

NATURAL GAS FIREPLACE INSERT:

Factory Equipped For Altitude 0-4500ft. (0-1370m)

Min. supply pressure 5“ WC (1.25 kpa)

Low Setting Man. pressure 1.6" WC (0.41 kpa)

Max. Manifold pressure 3.5" WC (0.87 kpa)

Orifice size #32 DMS

Minimum input 25,000 Btu/h (7.33 kW)

Maximum input 38,000 Btu/h (11.14 kW)

Min. supply pressure 11"WC (2.73 kpa)

Low Setting Man. pressure 6.4" WC (1.59 kpa)

Max. Manifold pressure 10" WC (2.48 kpa)

Orifice size #51 DMS

Minimum input 30,000 Btu/h (8.79 kW)

Maximum input 38,000 Btu/h (11.14 kW)

PROPANE GAS FIREPLACE INSERT:

Factory Equipped For Altitude 0-4500ft. (0-1370m)

MODEL -NG2HZI540E

HZI540EMODEL -LP2

Model/Modele:

-NG2

HZI540E

919-254

DO NOT REMOVE THIS LABEL /

NE PAS ENLEVER CETTE ETIQUETTE

Serial No. / No de serie

402

Duplicate Serial number

Listed:

Certified for/Certifi e pour: CANADA and U.S.A.

VENTED GAS FIREPLACE HEATER

Tested to:

FOYER AU GAZ À ÉVACUATION

CAN/CGA-2.17-M91(R2009)

ANSI Z21.88-2009/CSA 2.33-2009

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS. /

NE PAS UTILISER AVEC DUCOMBUSTIBLE SOLIDE.

FOYERAU

GAZ À ÉVACUATION -

Model/Modele:

-LP2

HZI540E

ÉÉQUIP A L'UISINE POUR GAZ PROPANE

MODELHZI540E-LP2

ÉÉQUIP A L'UISINE POUR GAZ NATURAL

MODELHZI540E-NG2

Pression d'allimentation minimum

Pression la tubulure d' chappement basse

Pression la tubulure d' chappement lev e

Dimensions de l'orifice

D bit Calorifique minimum

D bit Calorifique maximum

ééé

Pression d'allimentation minimum

Pression la tubulure d' chappement basse

Pression la tubulure d' chappement lev e

Dimensions de l'orifice

D bit Calorifique minimum

D bit Calorifique maximum

ééé

Mantel Clearances

FPI Fireplace Products International Ltd.,

Delta BC, CANADA

MADE IN CANADA /FABRIQUE AU CANADA

Minimum Clearances to Combustibles

from Insert

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and

Propane Installation Code, CSA B149.1.

This appliance is only foruse with the type of gas indicatedon the rating plate.

This appliance is not convertiblefor use with other gases unless acertified kit is used.

This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured

(mobile) home where not prohibitedby local codes. See owner's manual fordetails

WARNING. This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original

parts have been replaced, andthe fireplace re-approved by the authority havingjurisdiction.

Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel

Gas Code ou CSA-B149.1 envigueur.

AVERTISSEMENT :Ce foyer a été converti pour utilisation avec un foyer au gaz encastrable et ne peut être utiliser pour brûler du bois ou d'autres

combustibles solides à moins quetoutes les pièces d'origine aient été remplacéeset que le foyer ait été approuvéde nouveau par l'autorité compétente.

This vented gas fireplace heateris notfor use with air filters. Ne pas utiliser de filtre à airavec ce foyer au gaz à évacuation.

Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison

préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de

renseignements. Cet appareil ne peutpas être utilisé avec d'autres gaz saufsi une trousse de conversion certifiée estfournie.

Cet appareil n'est pas convertiblepour une utilisation avec d'autres gaz, saufsi un kit certifié est utilisé.

Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison

préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de

renseignements.

Electrical supply / Électrique 115VAC, 2.5 A, 60Hz, Less than 10A Fan Part # 911-071

Side wall A12” (305mm)

Ceiling B60” (1524mm)

12" Mantel Max. C 24” (610mm)

Min. Alcove Width K 56" (1422mm)

Max. Alcove Depth L36” (914mm)

*Min. Hearth Width D14” (356mm)

*Min. Hearth Length E44” (1016mm)

Max. Mantle Depth G 12" (305mm)

* See installation manual for hearth requirements.

*If unit is raised 6" from the floor - no hearth

required.

@ 24" form fireplace opening

4001172

For the State of Massachusetts, installation and repair must be done by a plumber or gasﬁtter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, ﬂexible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with

battery back up in the same room where the gas appliance is installed.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

REQUIREMENTS

5.08: Modifications to NFPA-54, Chapter 10

(2) Revise 10.8.3 by adding the following additional requirements:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for

residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than

seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall

be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled

equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is

installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery

operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure

served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of

qualified licensed professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon

monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of

thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions

shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight

(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The

sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation

unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by

the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or

structure used in whole or in part for residential purposes.

Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the

instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a

Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies

"special venting systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and

2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and

detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,

all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of

the installation.

MA Code - CO Detector

(for the State of Massachusetts only)

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE

INSTRUCTIONS

The L540E / HZI540E Gas Inserts must be installed

in accordance with these instructions. Carefully read

all the instructions in this manual ﬁrst. Consult the

"authority having jurisdiction" to determine the need

for a permit prior to starting the installation. It is the

responsibility of the installer to ensure this ﬁreplace

is installed in compliance with manufacturers

instructions and all applicable codes.

BEFORE YOU START

Safe installation and operation of this appliance

requires common sense, however, we are required

by the Canadian Safety Standards and ANSI

Standards to make you aware of the following:

CLOTHING OR OTHER FLAMMABLE

MATERIAL SHOULD NOT BE PLACED

ON OR NEAR THE APPLIANCE.

CHILDREN AND ADULTS SHOULD BE

ALERTED TO THE HAZARDS OF HIGH

SURFACE TEMPERATURES, ESPE-

CIALLY THE FIREPLACE GLASS, AND

SHOULD STAY AWAY TO AVOID BURNS

OR CLOTHING IGNITION.

INSTALLATION AND REPAIR SHOULD

BE DONE BY AN AUTHORIZED

SERVICE PERSON. THE APPLIANCE

SHOULD BE INSPECTED BEFORE

USE AND AT LEAST ANNUALLY BY A

PROFESSIONAL SERVICE PERSON.

MORE FREQUENT CLEANING MAY

BE REQUIRED DUE TO EXCESSIVE

LINT FROM CARPETING, BEDDING

MATERIAL, ETC. IT IS IMPERATIVE THAT

CONTROL COMPARTMENTS, BURNERS

AND CIRCULATING AIR PASSAGEWAYS

OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE

APPLIANCE SHOULD BE LOCATED

OUT OF TRAFFIC AND AWAY FROM

FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS

APPLIANCE CORRECTLY WILL VOID

YOUR WARRANTY AND MAY CAUSE A

SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE CARE-

FULLY SUPERVISED WHEN THEY ARE

IN THE SAME AREA AS THE APPLI-

ANCE. TODDLERS, YOUNG CHILDREN

AND OTHERS MAY BE SUSCEPTIBLE

TO ACCIDENTAL CONTACT BURNS. A

PHYSICAL BARRIERS IS RECOMMEND-

ED IF THERE ARE AT RISK INDIVIDUAL

IN THE HOUSE. TO RESTRICT ACCESS

TO A FIREPLACE OR STOVE, INSTALL

AN ADJUSTABLE SAFETY GATE TO

KEEP TODDLERS, YOUNG CHILDREN

AND OTHER AT RISK INDIVIDUALS OUT

OF THE ROOM AND AWAY FROM HOT

SURFACES.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE

INSTRUCTIONS

The Regency Gas Insert must be installed in

accordance with these instructions. Carefully

read all the instructions in this manual ﬁrst.

Consult the building authority having jurisdiction

to determine the need for a permit prior to starting

the installation.

NOTE: Failure to follow the instructions could

cause a malfunction of the heater which could

result in death, serious bodily injury, and/

or property damage. Failure to follow these

instructions may also void your ﬁre insurance

and/or warranty.

FOR YOUR SAFETY

This appliance requires air for proper combustion.

Always provide adequate combustion and

ventilation air. Follow instructions and

information in CAN/CGA B149 (in Canada) or

the National Fuel Gas Code ANSI Z223.1 (in the

USA), regarding requirements for combustion

and ventilation air.

SPECIFICATIONS

At pressures over 1/2 psig, the pipe to the unit

must be disconnected.

Gas Input Capacity:

Natural Gas 38,000 Btu/h

Propane 38,000 Btu/h

Min. Input

(with Proﬂame GTM or GTMF remote)

Natural Gas 25,000 Btu/h

Propane 30,000 Btu/h

Fuels: Approved for use with both natural gas,

and propane. Approved as is for use at 0' to

4,500' (0-1370m).

Electrical: 120V A.C. system.

Circulation Fan: Variable speed, 140 CFM.

Log Set: Ceramic ﬁbre, 7 per set - L540E

Glass Crystals: 8 lbs of glass crystals - HZI540E

Vent System: 3" x 4" The efﬁciency rating of

the appliance is a product thermal efﬁciency

rating determined under continuous operating

conditions and was determined independent of

any installed system.

GAS PRESSURE

TESTING

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shut off valve during any pressure testing

of the gas supply piping system at test pressures

equal to or less than 1/2 psig. (3.45 kPa).

INSTALLATION INTO A

SOLID FUEL BURNING

FIREPLACE OR

FACTORY BUILT

FIREPLACE

The L540E / HZI540E Gas Inserts have been

tested and approved to be vented into any

masonry ﬁreplace or approved solid fuel burning

factory built ﬁreplace that will allow the insert to

physically ﬁt into the ﬁrebox. Refer to "Minimum

Fireplace Dimensions" section for minimum

ﬁreplace clearances.

If the factory built ﬁreplace* height is too low for

your Insert, you may remove the smoke bafﬂe

plate, damper, refractory (ﬁrebricks), glass

doors, screen rails, screen mesh and log grates

from the factory built ﬁreplace as long as these

items are saved and are reinstalled in the event

that the Insert is removed.

Smoke shelves, shields and bafﬂes may be

removed if attached by mechanical fasteners.

If any part is removed it must not weaken the

structural integrity of the factory built ﬁreplace.

NOTE: Any alterations made to the listed solid

fuel burning factory built ﬁreplace may void the

listing of the ﬁreplace.

*Check with your local inspector before

commencing with this installation.

BEFORE YOU START

Safe installation and operation of this appliance

requires common sense, however, we are

required by the Canadian Safety Standards

and ANSI Standards to make you aware of

the following:

General Safety Information

1) The appliance installation must conform

with local codes or in the absence of local

codes, with CAN/CGA B149 (in Canada) or

the National Fuel Gas Code ANSI Z223.1 in

the U.S.A. This appliance should be installed

by a qualiﬁed gas ﬁtter technician only.

2) Installation and repair should be done

by a qualiﬁed service person.

3) The appliance should be inspected before

use and at least annually by a professional

service person. More frequent cleaning

may be required due to excessive lint from

carpeting, bedding material, animal hair, etc.

It is imperative that control compartments,

burners and circulating air passageways of

the appliance be kept clean.

4) See general construction and assembly

instructions. This appliance may only be

installed in a vented, noncombustible

ﬁreplace.

5) This appliance is Listed for bedroom

installations when used with a Listed Millivolt

Thermostat. Some areas may have further

requirements, check local codes before

installation.

6) Always connect this insert to a vent system

venting to the outside of the building

envelope. Never vent to another room or

inside a building. Make sure that the vent

is properly sized and is of adequate height

to provide the proper draft.

7) Inspect the venting system annually for

blockage and any signs of deterioration.

8) Any glass removed for servicing must be

replaced prior to operating the appliance.

9) To prevent injury, do not allow anyone who

is unfamiliar with the operation to use the

ﬁreplace.

10) Due to high temperatures, the appliance

should be located out of high trafﬁc areas

and away from furniture and draperies.

Children and adults should be alerted to

the hazards of high surface temperatures,

especially the ﬁreplace glass and gold

trims, and should stay away to avoid burns

or clothing ignition. Young children should

be carefully supervised when they are in

the same room as the appliance. Clothing

or other ﬂammable material should not be

placed on or near the appliance.

Emissions from burning wood or gas could

contain chemicals known to the State of

California to cause cancer, birth defects

or other reproductive harm.

Installer must mechanically attach the supplied

label to the inside of the ﬁrebox of the ﬁreplace

into which the gas ﬁreplace insert is installed.

"WARNING: This fireplace has been

converted for use with a gas ﬁreplace insert

only and cannot be used for burning wood or

solid fuels unless all original parts have been

replaced, and the ﬁreplace re-approved by the

authority having jurisdiction."

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

MATERIALS REQUIRED

Electrical power supply (120V) is required for the

gas control and fan to operate as this unit is supplied

with a GTMF remote control system which operates

both the gas valve and fan. Plug the 3 wire cord

into a suitable receptacle. Do not cut the ground

terminal off under any circumstances. When

connected with 120 volts, the appliance must be

electrically grounded in accordance with local

codes, current version of CSA C22.1 (in Canada)

or in the absence of local codes, with the National

Electrical Code ANSI/NFPA 70-1987.

INSTALLATION

CHECKLIST

Before installing vent system ensure that the damper

plate is open and secure to prevent the damper plate

from falling down and crushing the liner.

The Regency Gas Insert is installed as listed.

1) Check all clearances to combustibles, (Refer to

sections "Minimum Fireplace Dimensions and

Clearances to Combustibles)

2) Make the gas connection. (Refer to section "Gas

Connection") Gas connection is on the left side

of the appliance.

3) Install the two ﬂue liners (intake and exhaust)

to the sliding connector plate. (Refer to section

"Flue Liner Installation.")

4) Slide the unit half way into the ﬁreplace.

5) Pull the vent connector plate through the

brackets and fasten to the front plate. Refer to

section "Flue Liner Installation.")

6) Slide the unit fully into the ﬁreplace. Level if

necessary.

7) Install 4-AA batteries into receiver.

8) Plug the 3 wire cord into a suitable receptacle.

The 3 wire cord is located on the right side of

the unit.

9) Code remote control. See Remote Control

Instruction Manual.

10) Test gas pressure (Refer to section "Gas Pipe

Pressure Testing"). Check aeration system

(Refer to section "Gas Insert Aeration System").

11) Install standard and optional features. Refer to

the following sections:

a. Brick Panels

b. Enamel Panels

c. Log Set

d. Glass Crystals

e. Spa stones

. Low Proﬁle Faceplate with Optional Screen

. Full Screen Door

MINIMUM FIREPLACE

DIMENSIONS

The minimum ﬁreplace clearances & dimensions

for the Regency gas insert are shown in the

following diagrams:

Max Lentil

Bar Depth

Height

Depth

Width

(rear)

Width

(front)

10" 24" 16.75" 25" 34"

12) Final check: Before leaving this unit with the

customer, the installer must ensure that the

appliance is ﬁring correctly. This includes:

a) Clocking the appliance to ensure the correct

ring rate.

b) Adjusting the primary air, if required, to

ensure that the ame does not carbon. See

"Gas Insert Aeration System" section.

c) Ensuring that the appliance is venting

correctly.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

Door

Opening

16" Min

From Top of

Allowable

Mantel Area



)URPERWWRP

RIXQLW

Door

Opening

12" Min

From Top of

Allowable

Mantel Area



)URPERWWRP

RIXQLW

Diagram 1

Diagram 3

Diagram 2

Note: A 3-1/2" mantel deector to reduce

mantel height to 36" from bottom of unit

@ 1"depth.

A noncombustible mantel may be

installed at a lower height if the framing

is made of metal studs covered with a

noncombustible board.

MINIMUM CLEARANCES TO COMBUSTIBLES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of ﬁres is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this

decorative gas appliance be installed only in accordance with these instructions.

Clearance: Dimension Measured From:

A: Sides

12" / 305 mm From inside edge of faceplate / doors

B: Ceiling

60" / 1524 mm Bottom of unit

C: Mantel (Min. Height)*

*12" / 305mm

16"/ 406mm

From top of unit, or 36" from bottom of unit

From top of unit, or 40" from bottom of unit

D: Min. Hearth Depth

14" / 356mm

E: Min. Hearth Width

44"/ 1016mm

G: Max. Mantle Depth

12" / 305 mm @ 48" (1219mm) from bottom of unit

K: Min. Alcove Width

56" / 1422 mm

L: Max. Alcove Depth

36" / 914 mm

M: Optional mantel

deector

3-1/2" / 89mm

Notes: Non-combustible hearth required. If unit is raised 6" from the ﬂoor - no hearth is

required.

Otherwise:

Min. Hearth requirements - An R value of 1.75 is required to meet the requirements of the

hearth in front of this appliance. 1" of Calcium Silicate board available from Regency, part

number (296-936) plus 3/8" tile or equivalent would meet this requirement.

See part instruction sheet 919-133 for non-combustible Calcium Silicate board requirements.

MANTEL CLEARANCES WITHOUT DEFLECTOR MANTEL CLEARANCES WITH 3-1/2" DEFLECTOR

WARNING

Although this appliance passes safety

certiﬁcation, the hearth in front of the ﬁreplace

becomes very hot when the ﬁreplace heats. Do

not use the hearth as a seat or shelf.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

VENTING

THE APPLIANCE MUST NOT BE

CONNECTED TO A

CHIMNEY FLUE SERVING A

SEPARATE SOLID FUEL

BURNING APPLIANCE.

This appliance is designed to be attached to a

3" intake and a 4" exhaust aluminium ﬂex vent.

The ﬂue length must be a minimum length of 8 '

(2.44m) and a maximum of 35' (10.7m). See chart

for minimum distances from roof. Periodically check

that the vent is unrestricted.

Masonry chimneys may take various contours which

the ﬂexible liner will accommodate. However, keep

the ﬂexible liner as straight as possible, avoid

unnecessary bending.

GAS CONNECTION

1) If the appliance is to be installed into an existing

chimney system, thoroughly clean the masonry

or factory built ﬁreplace.

2) The appliance is provided with an opening on

the left hand side of the control compartment.

A 3/8" NPT gas supply pipe must be brought

near this inlet hole.

3) Locate the center point where the vent will pass

through the chimney above the appliance. Move

the appliance into the exact location where it is

to be installed. Ensure that the Insert is level.

4) Do not cut any sheet-metal parts of the ﬁre-

place, in which the gas ﬁreplace insert is to

be installed.

5) If the factory-built ﬁreplace has no gas access

hole(s) provided, an access hole of 1-1/2"

(37.5mm) or less may be drilled though the

lower sides or bottom of the ﬁrebox in a

proper workmanship like manner. This access

hole must be plugged with a non-combustible

insulation after the gas supply line has been

installed.

Air Intake pipe and exhaust must be attached to

the inlet and exhaust collars of the appliance with

a minimum of three screws per pipe.

GAS CONNECTION WARNING:

Only persons licensed to work

with gas piping may make the

necessary gas connections

to this appliance.

3" Air

Intake

4" Exhaust

Flue

The Air Intake and exhaust pipes must be attached

to the inlet and exhaust collars of the termination

cap with a minimum of three screws per pipe.

Part # Description

948-305 3" Flex - 35 ft. (Air intake)

948-336 4" Flex - 35 ft. (exhaust)

946-588 Co-linear DV Vertical Termination Cap

NOTE: Flashing should be securely

fastened to the chimney.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

Intake Liner

Exhaust Liner

Gear Clamps

Vent Connectors

Flue Connector

Plate Gasket

Flue Connector

Plate Guides

Flue Connector

Slide Tool

Flue Connector

Screws

Flue Connector

Plate

Properly installed Flue

Connector Plate

Rear tabs fully engaged

1) Detach the Flue Connector Plate from the unit by removing the

Connector Plate Screws and sliding the Flue Connector Plate rearward

and off the unit.

NOTE: Flue Plate Connector Gasket

must not be damaged or removed.

Care must be taken to ensure that this

gasket remains intact to prevent ﬂue

leakage.

5) When the Flue Connector Plate is close to the front of the unit, engage

the Flue Connector Screws and carefully tighten the Flue Connector

Plate the ﬁnal amount.

** Make sure the Rear Tabs connect into their respective slots in the Flue

Connector Plate. Failure to do so will result in ﬂue gas leakage and

degrade the operation of the unit ** (See diagram below of location.)

The Flue connection is complete when the Flue Connector Plate is fully

forward and the Rear Tabs are fully engaged.

6) Remove the Flue Connector Tool and store for future use.

2) Attach the Flue Liners onto the Flue Connector Plate using non RTV

type sealant, then fasten with 3 screws.

See the section in this manual on Venting installation.

3) Position the unit in front of the ﬁreplace opening, start the Flue Connec-

tor Plate into the Flue Connector Plate Guides.

Flue Connector Plate

Flue Connector Slide Tool

Connector plate screws

4) Use the Flue Connector Slide Tool to slowly pull the Flue Connector

Plate forward as you move the Insert rearward into the Fireplace Chase.

FLUE / VENT INSTALLATION

WARNING:

Failure to position the parts in accordance with these diagrams or failure

to use only parts speciﬁcally approved with this appliance may result in

property damage or personal injury.

(L390E Shown)

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

LEVELING LEG ADJUSTMENT

The L540E / HZI540E inserts are equipped with 4 levelling legs that are accessible while the appliance is in its ﬁnal installation position. The unit can

be adjusted up to 5/8" (16mm). The faceplate must not be installed to do this adjustment, if installed, remove faceplate.

Remove left and right inner panels by sliding them forward. The rear levelling bolts are located in the back corners of the ﬁrebox and can be adjusted

using a 7/16" wrench. Rotate the bolts clockwise to raise the rear of the ﬁrebox.

The front levelling bolts are adjusted before installing the faceplate. Located on the left on right of the outer shell, they can also be adjusted using a

7/16" deep socket with extension.

When the appliance is in position, adjust the bolts to level the appliance, making sure that the appliance is also level and is sitting on all 4 bolts to

prevent rocking.

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

Air Shutters are required to increase or decrease the amount of air that is

mixed with the fuel before combustion. This will have an affect on how well

the fuel combusts and how the ﬂame physically appears.

Low primary air will leave a taller, yellower ﬂame while higher primary air will

leave a lower, bluer ﬂame.

This setting is largely for appearance, however, not enough primary air may

lead to carboning, sooting or a ﬂame that reaches the top of the ﬁrebox.

Situations that may require more primary air are; units that are burning

propane, units installed at higher elevations or units that are run on high

most of the time.

The L540E / HZI540E is equipped with an air shutter that is accessible from

outside the ﬁrebox and can be adjusted during operation.

Aeration adjustments should only be made after the unit has been on for 30

minutes to 1 hour.

Slide the Air Shutter Lever towards you to increase the primary air setting.

Slide the Air Shutter away from you to decrease the primary air setting.

Below you will see a chart showing the minimum primary air settings.

These are set from the factory, but due to fuel conversions or installation

conditions, the air setting may need to be adjusted.

Open

Unit Fuel Type Min. Air Setting

L540E NG 1/8" (3mm)

L540E LP 3/8" (9mm)

HZI540E NG 1/8" (3mm)

HZI540E LP 3/8" (9mm)

AIR SHUTTER ADJUSTMENT

Air Shutter

Air Shutter Lever

Gas Orifice

Burner Mounting

Bracket

Firebox cut-away to

show location of

Air Shutter Lever

1) Slide the Air Shutter Lever towards you to increase the primary air set-

ting.

2) Slide the Air Shutter away from you to decrease the primary air setting.

Below you will see a chart showing the minimum primary air settings.

CAUTION: Carbon will be produced if air shutter is closed too much.

Note: any damage due to carboning resulting from improperly setting

the aeration controls is NOT covered under warranty.

Note: Aeration Adjustment should only be performed by an authorized

Regency Installer at the time of installation or service.

Push to close - Pull to open

Unit Front

Unit Back

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas sup-

ply piping system by closing its individual manual

shut-off valve during any pressure testing of the

gas supply piping system at test pressures equal

to or less than 1/2 psig. (3.45 kPa). Disconnect

piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator

built into the gas control, and should be checked

at the pressure test point.

Note: To properly check gas pressure, both

inlet and manifold pressures should be

checked using the valve pressure ports

on the valve.

1) Make sure the valve is in the "OFF" position.

2) Loosen the "IN" and/or "OUT" pressure tap(s),

turning counterclockwise with a

1/8" wide ﬂat screwdriver.

3) Attach manometer to "IN" and/or "OUT" pressure

tap(s) using a 5/16" ID hose.

4) Light the pilot and turn the valve to "ON" position.

5) The pressure check should be carried out with

the unit burning and the setting should be within

the limits speciﬁed on the safety label.

6) When ﬁnished reading manometer, turn off the

gas valve, disconnect the hose and tighten the

screw (clockwise) with a 1/8" ﬂat screwdriver.

Note: Screw should be snug, but do not over

tighten.

HIGH ELEVATION

This unit is approved for altitude 0 to 4500 ft. (CAN1

2.17-M91).

GAS LINE

INSTALLATION

Since some municipalities have additional local

codes it is always best to consult with your local

authorities and the CAN/CGA B149 installation

code.

For USA installations follow local codes and/or the

current National Fuel Gas Code, ANSI Z223.1.

When using copper or ﬂex connectors use only

approved ﬁttings. Always provide a union so that

gas lines can be easily disconnected for servicing.

Flare nuts for copper lines and ﬂex connectors are

usually considered to meet this requirement.

NOTE: A shutoff / dante valve should be sup-

plied in or near the unit (or as per local codes)

for ease of servicing this appliance.

IMPORTANT: Always check for gas leaks with

a soap and water solution or gas leak detector.

Do not use open ﬂame for leak testing.

L540E-NG / HZI540E-NG

SYSTEM DATA

Min. Supply Pressure 5" WC (1.25 kpa)

Manifold Pressure 3.5" WC (0.87 kpa)

Orice Size #32 DMS

Maximum Input 38,000 Btu/h

(11.14 kW)

L540E-LP / HZI540E-LP

SYSTEM DATA

Min. Supply Pressure 11" WC (2.73 kpa)

Manifold Pressure 10" WC (2.49 kpa)

Orice Size #51 DMS

Maximum Input 38,000 Btu/h

(11.14 kW)

Note: If you have an incorrect ame pattern,

contact your Regency

dealer for further

instructions.

Incorrect ﬂame pattern will have small, probably

yellow ﬂames, not coming into proper contact

with the rear burner or ﬂame sensor.

Burner

Flame Sensor

Pilot

Ignitor

885 S.I.T. VALVE

DESCRIPTION

1) 6 Stage ﬂame adjustment

2) Pilot adjustment

3) Outlet Pressure Tap

4) Inlet Pressure Tap

5) Pilot Outlet

6) Main Gas Outlet

7) Main Gas Inlet

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

919-255

10/16/14

L540E / HZI540E

CONVERSION FROM NG TO LP

L540E/HZI540E using SIT 885 NOVA Gas Valve

Before you begin:

Shut off the gas supply to the unit.

Disconnect all electrical supply to the unit.

Always let the appliance cool to room temperature before servicing.

1) Remove the left side control cover.

2) Loosen both screws at the top of the valve about ½ way out. Lift the

valve body and lean outward. The Valve Brackets will rest open as

shown on the right.

3) Disconnect the Cable coming from the Pressure Regulator Motor.

WARNING

This conversion kit shall be installed by a qualiﬁed service agency in

accordance with the manufacturer’s instructions and all applicable codes

and requirements of the authority having jurisdiction. If these instructions

is not followed exactly, a ﬁre, explosion or production of carbon monoxide

may result causing property damage, personal injury or loss of life. The

qualiﬁed service agency is responsible for the proper installation of this

kit. The installation is not proper and complete until the operation of the

converted appliance is checked as speciﬁed in the manufacturer’s instruc-

tions supplied with the kit.

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION!

Side control cover

Cable from motor

The valve in the L390E is attached using 2 screws and 2 hooks located

below the valve. Loosening the screws part way and lift the valve to

disengage the hooks.

The valve will then hinge outward allowing access to the components

and pressure taps located on the top of the valve without completely

removing the valve.

Conversion Kit 298-972 includes:

1 911-011 Stepper Motor LP for 885 SIT

1 904-964 Oriﬁce #51

1 910-101 Pilot Oriﬁce LP

1 918-590 Decal - Conversion to LP

1 908-528 Label Propane

4) Remove and discard 2 Pressure regulator screws A (T20 or slot), Pres-

sure Regulator B, Spring and Diaphragm C.

5) Ensure the rubber gasket, which is preﬁtted as part of the Assembly,

is properly positioned. Install the new Pressure Regulator using the 2x

M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that

the screw threads are cross threaded or stripped, replace the valve

assembly.

Install the enclosed propane identiﬁcation label to the valve body where it

can be easily seen.

CONVERSION FROM NG TO LP

L540E/HZI540E using SIT 885 NOVA Gas Valve

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

919-255 10/16/14

L540E / HZI540E

6) Ensure the rubber gasket, which is preﬁtted as part of the Assembly,

is properly positioned. Install the new Pressure Regulator using the 2x

M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that

the screw threads are cross threaded or stripped, replace the valve

assembly.

Install the enclosed propane identiﬁcation label to the valve body where it

can be easily seen.

7) Re-attach the Pressure Regulator wire, and re-situate the Gas Valve,

secure the screws that fasten the Gas Valve Mounting Brackets.

8) Remove burner (see burner removal section in manual).

13) Ensure the pilot light is in the correct orientation to the Burner.

Reconnect the gas and electrical supply to the appliance. Start the

appliance. (see section on Lighting Instructions) Ensure that pilot and

burner ignition is completed without delay. Check both your inlet and

outlet pressures at full load. With a soapy solution, leak test the entire

system. Verify both the correct ﬂame and pilot appearance.

14) See Gas Pipe Pressure Testing in manual.

15) Adjust aerations settings - see Air Shutter Adjustment section in the

manual.

11) Remove pilot retainer clip with pliers and pull off the pilot cap to expose

the pilot orice.

12) Unscrew the pilot orice with the allen key; then replace with the LPG

pilot orice and the pilot cap, provided in the kit.

Installer Notice:

These instructions must be left

with the appliance.

Pilot retainer clip

10) Using a 3/8” socket wrench, loosen and remove the main gas oriﬁce.

Replace with the LP gas oriﬁce. Conﬁrm the oriﬁce size marked on the

Oriﬁce with the Rating Label on the appliance

Screw Locations

Top Bracket

IMPORTANT: THIS TOP BRACKET MUST BE REMOVED FOR LP

9) IF TOP BRACKET IS INSTALLED

a) Loosen 3 screws on the bottom bracket (see below for location)

b) Slide the top bracket over screws, retighten the screws.

c) Discard Top Bracket

L540E-2 / HZI540E-2 Direct Vent Gas Insert

INSTALLATION

GTMF REMOTE SYSTEM - IMPORTANT: The 120V fan control module serves as the power source for this unit. The AA batteries in the

receiver only serve as a backup in case 120 volt power lost within the home.

PROFLAME REMOTE SYSTEM GTMF WITH FAN (L540E / HZI540E)

WIRING DIAGRAM

CAUTION: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause

improper and dangerous operation.

Ground

Green

Neutral

Live

Black

Red

FanThermodisc

(normally open)

Ground

120V AC

60 Hz

Fan

Black

Red

Black

Proflame System

Configuration

886 GTMF

Wire Diagram

SureFire™ Switch

0.584.907

Caution: Ensure that the wires do not touch any

hot surfaces and are away from sharp edges.

Thermostat

(Optional)

See optional wall thermostat

installation in this manual.

885

La page charge ...

Regency Fireplace Products Horizon HZI540EB Le manuel du propriétaire

Marque: Regency Fireplace Products

Modèle: Horizon HZI540EB

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

Liberty L540EB

Télécharger le PDF

rapport

dans d''autres langues

English: Regency Fireplace Products Horizon HZI540EB Owner's manual

Regency Fireplace Products Horizon HZI540EB Le manuel du propriétaire

Ce manuel convient également à

Regency Fireplace Products Horizon HZI540EB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents