Uniden PRO538HHFM Manuel utilisateur

PRO538HHFM

Handheld CB Radio

Printed in Vietnam

U01UT433ZZA(0)

Irving, Texas

CONTENTS

INTRODUCTION .............................................................................5

FEATURES ..................................................................................5

SAFETY NOTICE ........................................................................6

UNIDEN CONTACT INFORMATION ...........................................6

INCLUDED IN YOUR PACKAGE ...................................................6

PARTS OF THE RADIO ..................................................................7

DEFINITIONS ..............................................................................8

LCD ...............................................................................................10

SETUP ........................................................................................... 11

INSTALL ANTENNA ..................................................................11

Rubber Antenna ....................................................................12

External Antenna ..................................................................12

CONNECT TO POWER.............................................................12

Rechargeable Ni-MH Batteries ............................................. 13

Alkaline Batteries ..................................................................15

In-Vehicle Adapter ................................................................17

CONNECT EXTERNAL SPEAKER AND MICROPHONE .........18

OPERATION .................................................................................18

BASIC OPERATION ..................................................................18

EMERGENCY OPERATION ...................................................... 22

DUAL WATCH ...........................................................................22

Programming Dual Watch Channels .................................... 22

AUTOMATIC NOISE LIMITER ..................................................22

WEATHER .................................................................................23

MAINTENANCE ............................................................................23

TROUBLESHOOTING ..................................................................23

CB OPERATION ........................................................................24

CB Communication Codes ................................................... 24

SERVICE AND REPAIR INFORMATION...................................25

4

FREQUENCY LISTS .....................................................................26

CB CHANNEL FREQUENCY LIST ............................................26

WEATHER CHANNEL FREQUENCY LIST ..............................27

SPECIFICATIONS .........................................................................28

GENERAL .................................................................................. 28

TRANSMITTER .........................................................................29

RECEIVER ................................................................................29

FCC PART 15 AND ISED COMPLIANCE ...................................30

FCC AND ISED STATEMENT .......................................................32

ISED ANTENNA STATEMENT ..................................................34

ÉNONCÉ D’ANTENNE ISED ....................................................34

ONE-YEAR LIMITED WARRANTY ..............................................34

5

INTRODUCTION

The PRO538HHFM radio is a hand-held radio designed for use in the

Citizens Band (CB) Radio Service. It will operate on any of the 40 CB

frequencies authorized by the Federal Communications Commission

(FCC). Your radio features a superheterodyne circuit with Phase

Locked Loop techniques to assure precise frequency control.

NOTE: Make sure you have read and understood part 95 of the

FCC rules and regulations before using the transmitter.

FEATURES

• 40 CB channels (AM/FM modes)

• 10 Weather channels

• AGC (Automatic Gain Control) for a constant sound level.

• Automatic Noise Limiter to reduce pulse noise.

• Backlight On/O; Dual backlight colors (Amber and White)

• Battery pack for 8 AA Ni-MH or 6 AA alkaline batteries (batteries

are not included).

• Compatible with CB MIC hanger.

• Dual Channel Watch

• External speaker jack and external MIC jack. Includes In-Vehicle

adapter.

• Full Channel Scan

• High/Low power saver switch (HI = 4W; LOW = 1W)

• Instant Channel 9/19

• Key Lock

• Portable and In-Vehicle Use

• RF Gain Control

• Rotary Channel Selector

6

SAFETY NOTICE

• Do not expose the PRO538HHFM to water or extreme

temperatures.

• Do not leave batteries installed over a long period of time as

leakage may occur and cause damage to the radio.

• Never use dierent batteries from the ones suggested.

• Never use harsh chemicals to clean this radio. Use a damp soft

cloth.

UNIDEN CONTACT INFORMATION

You can get answers 24/7 at our website: www.uniden.com.

INCLUDED IN YOUR PACKAGE

If any of these items are missing or damaged, immediately contact

your place of purchase or www.uniden.com.

PRO538HHFM Radio

(shown with Ni-MH battery

case attached)

Rubber (Whip) Antenna

Belt Clip In-Vehicle Adapter

7

Ni-MH Battery Case Alkaline Battery Case

Not shown: Hanger MIC with Screw and Wrist Strap

PARTS OF THE RADIO

3

Key 1

2

8

6

4

J1

5

1K2K1

J2

J - Jack

K - Knob

Key - Key

None - Other

LEGEND

Key 2

Key 3

Key 4

Key 5

Key 6

7

8

DEFINITIONS

ITEM NAME PURPOSE

J1 External Microphone

jack

Attach external microphone (not

included)

J2 External Speaker jack Attach external speaker (not

included)

K1 CH/RF GAIN knob Channel: Turn knob to select

channels.

RF Gain (AM Only): Press

FUNC + GAIN key and turn this

knob to adjust receiving gain.

Color Selection mode: Press

FUNC + COLOR key and turn

this knob to change backlight

color.

Scan mode: Resume scanning

or change scan direction.

K2 Power/VOL; SQ Turns power on and o and

adjusts volume and squelch

levels.

Key 1 9/19/DUAL Instantly recall channels 9 and

19.

Press FUNC and this key to

enter Dual Channel Watch

mode.

Press FUNC and hold this

key to program Dual Watch

Channels.

Key 2 FUNC Function key. Press this key to

unlock secondary key functions.

9

ITEM NAME PURPOSE

Key 3 ANL/GAIN Press to turn ANL on and o.

Press FUNC and this key to

access RF Gain Setting Mode.

Key 4 AM/FM (PWR H/L) Press to enter AM or FM modes.

Press FUNC and this key to set

power to high or low.

Key 5 SCAN/WX Press to start and stop

scanning.

Press FUNC. and this key to

access Weather Channels.

Key 6 /COLOR Press to turn backlight on/o.

NOTE: Backlight does not

support the orange

letters on the keys.

Press and hold to turn keylock

on/o.

Press FUNC and this key

to enter color setting mode.

Turn the CH/RF GAIN knob to

select either an amber or white

background. Press /

COLOR to set it (see page

19).

1 Antenna Location for attaching the rubber

whip antenna.

2 Push-to-Talk button Push to transmit (talk) to other

radios.

3 Battery Case Release Slide up to release battery case

from the unit.

10

ITEM NAME PURPOSE

4 Charge LED Turns red when battery begins

charging.

NOTE: The LED does not

indicate when charging is

complete.

5 Clip Location Use a carabiner clip (not

included) to attach the radio to a

belt loop, strap, etc.

6 MIC Microphone Location

7 Charging Jack (Ni-MH

battery case only)

Connect DC charge plug from

In-Vehicle adapter.

8 Battery Case Location of Ni-MH or alkaline

battery cases or In-Vehicle

adapter when connected to the

PRO538HHFM. (Ni-MH battery

case shown.)

LCD

TX F

WX DW HI

LO

SIG

PWR

1359+30

0.5 1 2 3 4

AM FM

ANL

SCAN

GAIN

11

LCD ITEM MEANING

TX Transmitting indicator

F Function indicator

AM AM mode indicator

FM FM mode indicator

ANL Automatic Noise Limiter indicator

WX Weather Channel indicator

DW Dual Watch indicator

HI TX Power indicator: HI = 4W

SCAN Scan function active

LO TX Power indicator: LO = 1W

88 Channel Number/RF Gain (0 - 10)

Battery Strength (4 levels - 3, 2, 1, and

Low Battery. Battery icon blinks in Low

Battery mode.)

Key lock function active

SIGNAL

POWER

1359

+30

0.5

1 2 3 4

S/RF meter (10 steps)

Strength of incoming signal; Strength of

transmission power.

GAIN

RF Gain Level indicator (10 steps)

SETUP

INSTALL ANTENNA

The PRO538HHFM can use either a rubber “whip” antenna or an

external antenna (not included).

12

Rubber Antenna

1 Insert the rubber antenna (included) onto the radio’s antenna jack.

2 Rotate the antenna clockwise until it clicks into place.

NOTE: If using the rubber antenna or connecting the external

antenna to the radio’s antenna terminal, the PRO538HHFM must

use either of the Ni-MH or Alkaline battery cases for power.

External Antenna

The external antenna connects to the In-Vehicle’s external antenna

jack. See the graphic on page 13 for the external antenna jack

location.

1 Remove the rubber antenna from the PRO538HHFM.

CAUTION: When the In-Vehicle adapter is attached to radio, the

radio will switch to external antenna mode. Be sure to remove the

rubber antenna from the radio’s antenna terminal.

If the rubber antenna or the external antenna stays connected to the

radio’s antenna terminal, the transmit power to the external antenna

terminal will be signicantly reduced.

2 Slide the In-Vehicle adapter onto the radio.

3 Install the external antenna according to the manufacturer’s

instructions.

4 Connect the external antenna connector to the external antenna

jack on the In-Vehicle adapter.

5 Connect the 12V DC cigarette plug from the In-Vehicle adapter to

your vehicle.

CONNECT TO POWER

There are several methods to power your PRO538HHFM:

• Ni-MH batteries (case included)

• Alkaline batteries (case included)

13

• In-Vehicle adapter connects the PRO538HHFM to the vehicle’s

12V DC cigarette port

Connect to

PRO538HHFM Radio.

DC Power Plug:

Connect to DC12V Vehicle

Power (Cigarette) Jack.

External CB

Antenna Connector

Charge Plug:

Connect to Ni-MH

Battery Case.

VEHICLE ADAPTER

Rechargeable Ni-MH Batteries

The PRO538HHFM comes with a battery case for 8 AA Ni-MH batteries

(batteries not included).

1 Separate the two sides of the case by pulling them in the

directions noted on the shell.

2 Insert the 8 batteries according to the directions shown inside the

NiMH battery case.

CAUTION: Do not mix charged and uncharged batteries.

14

+ + +

+ + + +

+

3 Close the case. Align the bottom sides as shown and press the

two sides together.

4 Connect the battery case to the PRO538HHFM as shown.

PRO538HHFM

Ni-MH Battery Case

CAUTION: Do not attempt to charge Alkaline batteries in the Ni-MH

battery case as they may leak or catch re.

15

Charge Ni-MH Batteries

1 Verify that the Ni-MH batteries are inserted into the case.

2 Insert the In-Vehicle adapter’s charge plug into the Ni-MH battery

case. (See page 7 for the Ni-MH case location and page 13

for the location of the In-Vehicle adapter’s charge plug.)

3 When the plug is connected, the red LED on the battery case

lights up.

The charging current is 230mA (Nominal). When the radio is o, for

example, a discharged battery with a capacity of 2300mAh requires

about 10 hours of charging. If you charge the radio with the power ON,

the charging current will be reduced to about 80mA and requires about

16 hours of charging (it changes depending of the battery capacity and

condition). If you only want to charge the battery, turn o the radio’s

power.

You can remove the Ni-MH battery case from the radio to recharge

separately. Connect the radio to the Alkaline batteries/case or to the In-

Vehicle adapter to power the radio if needed.

CAUTION: Charging the battery for long periods of time will damage

the battery.

NOTE: The LED will not indicate when charging is complete.

NOTE: This plug is for charging only and is not intended to

power the radio. If you charge the battery while the battery case

is attached to the radio, the battery icon displayed on the radio

indicates always full while charging. The battery icon does not

indicate charging status; the charging is done directly to the

batteries without going through the radio.

Alkaline Batteries

The PRO538HHFM comes with a battery case for 6 AA Alkaline

batteries (batteries not included).

16

1 Separate the two sides of the case by pulling them in the

directions noted on the shell.

2 Insert the 6 batteries according to the directions show inside the

alkaline battery case.

+

3 Close the case. Align the bottom sides as shown and press the

two sides together.

17

4 Connect the battery case to the PRO538HHFM as shown.

PRO538HHFM

ALK Battery Case

CAUTION: Mixing new and used batteries will reduce performance.

Do not charge Alkaline batteries as they may leak or catch re.

NOTE: If you do not use the radio for a long time, remove the

batteries from the battery case.

In-Vehicle Adapter

The PRO538HHFM comes with an In-Vehicle adapter to connect it to

the vehicle’s 12V DC cigarette plug.

1 Connect the In-Vehicle adapter to the PRO538HHFM.

2 Connect the In-Vehicle adapter’s 12V DC cigarette plug to your

vehicle.

18

CONNECT EXTERNAL SPEAKER AND

MICROPHONE

Your radio supports an external speaker and microphone. The external

speaker and microphone are sold separately.

EXTERNAL SPEAKER

Impedance 8 Ohms

Connect to EXT.SP. jack (⅛-in/3.5 mm)

Notes The internal speaker is disabled when an external

speaker is connected.

EXTERNAL MICROPHONE

Connect to MIC jack (2.5 mm Electret type)

OPERATION

BASIC OPERATION

Turning the

radio on

Turn the VOL/SQ knob clockwise until it clicks and

the LCD display turns on.

Turning the

radio o

Turn the VOL/SQ knob counter-clockwise until it

clicks and the LCD display turns o.

Adjusting

Squelch

Turn the VOL/SQ knob counter-clockwise to open

squelch or clockwise to close it.

Select a mode Press AM/FM key to select a mode as follows:

AM → FM → AM

Turn backlight

on and o

Press the key to turn the LCD backlight on

for 10 seconds. Press it again while the backlight is

on to turn it o.

NOTE: Backlight does not support orange

letters on the keys.

19

Changing

backlight color

1 Press FUNC and COLOR key to enter

Backlight Setting mode.

2 Turn the CH/RF GAIN knob to select between

White and Amber. The LCD and keys ash.

Press FUNC or COLOR key again to set the

color and exit Backlight Setting mode.

NOTE: There is no time-out when in Backlight

Color mode.

NOTE: Backlight does not support the orange

letters on the keys.

Selecting a

channel

Turn the CH/RF GAIN knob to select a channel

(clockwise to increase the channel number or

counter-clockwise to decrease the channel

number).

Changing the

volume

After turning the radio on, turn the VOL/SQ knob

clockwise to increase the volume; turn it counter-

clockwise to decrease the volume.

Setting Key

Beep (Default

= ON)

When key beep is on (default), the radio beeps

whenever a key is pressed or a knob is turned.

1 To change the key beep status, turn o the

PRO538HHFM.

2 Press and hold the key while turning

the radio on.

3 If the radio beeps, the key beep function is now

on. If the radio does NOT beep, the key beep

function is o.

20

Transmitting

1 Tune the radio to the channel you want to

transmit on, and listen to make sure the

channel is clear.

2 Press and hold the PTT. TX displays

3 Hold the microphone about 2 inches away from

your mouth and speak in a normal voice.

4 Release the PTT key to listen for a response.

Adjust RF

Gain

1 Press FUNC and ANL/GAIN to enter RF Gain

Setting mode. The GAIN bar blinks.

2 Turn the CH/RF GAIN knob to adjust Gain

levels (0 - 10). The selected level displays as a

7 segment number and the GAIN bar will blink.

The Gain level number reects in the number

of Gain bar boxes.

3 Press FUNC or ANL/GAIN again to store

the setting and return to the main operations

screen.

NOTE: RF Gain only applies to AM mode. No RF

Gain levels display in FM or WX modes.

21

Scanning

channels

NOTE: Before starting the scan, adjust the

position where Squelch closes on the

channel without a signal. If you turn the

knob all the way clockwise, the scan will

not stop unless the radio receives a strong

signal.

Press SCAN in AM or FM mode; the radio

scans the channels, stopping when it receives

a transmission. Scanning resumes if no signal

received for 3 seconds. Press SCAN again to stop

scanning.

Turn CH/RF GAIN knob while scanning to change

scan direction.

When stopped on a channel, turn CH/RF GAIN

knob to resume scanning.

Lock keys

to prevent

accidental

activation.

Press and hold the key to activate key lock;

the Lock icon displays. Only the PTT and

keys and the VOL/SQ knob are active.

With Key Lock activated, press and hold the

key to deactivate key lock; the Lock icon goes away

and all keys are now active.

Go to Instant

Channel 9/19

Press 9/19 from any channel (rst press): Goes to

CH 9. 9 displays in the Channel Indicator.

Second press: Goes to CH 19. 19 displays in the

Channel Indicator.

Third press: Returns to original channel. That

channel number displays in the Channel Indicator.

Select

Transmit

Power Level

Press FUNC and then press PWR H/L. The power

level alternates between High and Low. The

appropriate icon displays on the screen.

Power setting cannot be changed while in WX

mode; HI and LO icons will not display.

La page charge ...

Uniden PRO538HHFM Manuel utilisateur

Uniden PRO538HHFM Manuel utilisateur

dans d''autres langues

Autres documents