PRESIDENT WALKER II FCC Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
Owner’s manual / Manual del usuario
Manuel d’utilisation / Manual do usuário
with / con /avec / com
Downloaded from www.cbradio.nl
Un vistazo a vuestro PRESIDENT WALKER II FCCYour PRESIDENT WALKER II FCC at a glance
Votre PRESIDENT WALKER II FCC en un coup d'œil
Uma olhada no seu PRESIDENT WALKER II FCC
3
SUMARIO
INSTALACIÓN ......................................................................................... 17
UTILIZACIÓN ........................................................................................... 19
MENÚS .................................................................................................... 22
FUNCIÓN CON LA PALANCA DE EMISIÓN PTT .................................... 25
CARACTERÍSTICAS TÉCNICAS ............................................................... 25
GUÍA DE PROBLEMAS ............................................................................ 25
COMO EMITIR O RECIBIR UN MENSAJE ............................................... 26
LÉXICO .................................................................................................... 26
CONDICIONES GENERALES DE GARANTÍA ......................................... 28
TABLAS DE FRECUENCIAS CB Y METEOROLÓGICAS .......................... 55
SUMMARY
INSTALLATION ........................................................................................... 5
HOW TO USE YOUR TRANSCEIVER .......................................................... 7
MENU ...................................................................................................... 10
FUNCTION WITH PTT SWITCH ................................................................. 12
TECHNICAL CHARACTERISTICS ............................................................. 13
HOW TO TRANSMIT OR RECEIVE A MESSAGE ..................................... 13
TROUBLE SHOOTING .............................................................................. 13
GLOSSARY .............................................................................................. 13
GENERAL WARRANTY CONDITIONS .................................................... 15
FREQUENCY AND WEATHER CHANNEL TABLES ................................... 55
SOMMAIRE
INSTALLATION ..........................................................................................30
UTILISATION .............................................................................................. 32
MENUS .....................................................................................................35
FONCTION AVEC LA PÉDALE D’ÉMISSION PTT .....................................38
CARACTÉRISTIQUES TECHNIQUES ..........................................................38
GUIDE DE DÉPANNAGE ..........................................................................39
COMMENT ÉMETTRE OU RECEVOIR UN MESSAGE ..............................39
GLOSSAIRE ..............................................................................................39
CONDITIONS GÉNÉRALES DE GARANTIE .............................................41
TABLEAUX DES FRÉQUENCES CB ET MÉTÉO ..........................................55
Français
Español
English
SUMÁRIO
INSTALAÇÃO .......................................................................................... 43
UTILIZAÇÃO ............................................................................................ 45
MENUS .....................................................................................................................48
FUNÇÃO COM A ALAVANCA DE EMISSÃO PTT .................................. 51
CARACTERÍSTICAS TÉCNICAS ............................................................... 51
GUIA DE PROBLEMAS ............................................................................ 51
COMO TRANSMITIR OU RECEBER UMA MENSAGEM .......................... 52
GLOSSÁRIO ............................................................................................ 52
CONDIÇÕES GERAIS DE GARANTIA .................................................... 54
TABELAS DE FREQUÊNCIAS CB E METEOROLÓGICAS ........................ 55
Português
4
The guarantee of this transceiver is valid only in the country of purchase.
WARNING !
Before using, be careful never to transmit without
first having connected the antenna (connection
“B” situated on the back panel of the equip-
ment) or without having set the SWR (Standing
Wave Ratio) ! Failure to do so may result in
destruction of the power amplifier, which is not
covered by the guarantee.
WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
English
5
Welcome to the world of the new generation of CB radios. The new PRESIDENT
range gives you access to top performance transceiver equipment. With the
use of up-to-date technology, which guarantees unprecedented quality, your
PRESIDENT WALKER II FCC is a new step in personal communication and is the
surest choice for the most demanding of professional CB radio users. To ensure
that you make the most of all its capacities, we advise you to read carefully this
manual before installing and using your PRESIDENT WALKER II FCC.
A) INSTALLATION
1) WHERE AND HOW TO MOUNT YOUR MOBILE CB RADIO
a) You should choose a well ventilated place most appropriate setting from
a simple and practical point of view.
b) Your CB radio should not interfere with the driver or the passengers.
c) Remember to provide for the passing and protection of different wires
(e.g. power, antenna, accessory cabling) so that they do not in any way
interfere with the driving of the vehicle.
d) To install your equipment, use the cradle (1) and the self-tapping screws
(2) provided (drilling diameter 1.126 in / 3.2 mm). Take care not to damage
the vehicle’s electrical system while drilling the dash board.
e) Do not forget to insert the rubber joints (3) between the CB and its support
as these have a shock-absorbing effect which permits gentle orientation
and tightening of the set.
f) Choose where to place the microphone support and remember that the
microphone cord must stretch to the driver without interfering with the
controls of the vehicle.
- N.B.: As the transceiver has a frontal microphone socket, it can be set into
the dash board. In this case, you will need to add an external loud speaker
to improve the sound quality of communications (connector EXT SP situated
on the back panel: C). Ask your dealer for advice on mounting your CB
radio.
2) ANTENNA INSTALLATION
a) Choosing your antenna
- For CB radios, the longer the antenna, the better its results. Your dealer will
be able to help you with your choice of antenna.
b) Mobile antenna
- Must be fixed to the vehicle where there is a maximum of metallic surface
(ground plane), away from windscreen mountings.
- If you already have a radio-telephone antenna installed, the transceiver
antenna should be higher than this.
English
6
- There are two types of antenna: pre-regulated which should be used on a
good ground plane (e.g. car roof or lid of the boot), and adjustable which
offer a much larger range and can be used on a smaller ground plane (see
§ HOW TO ADJUST SWR, below).
- For an antenna which must be fixed by drilling, you will need a good contact
between the antenna and the ground plane. To obtain this, you should
lightly scratch the surface where the screw and tightening star are to be
placed.
- Be careful not to pinch or flatten the coaxial cable (as this runs the risk of
break down and/or short-circuiting).
- Connect the antenna (B).
OUTPUT RADIUS PATTERN
c) Fixed antenna
- A fixed antenna should be installed in as clear space as possible. If it is fixed
to a mast, it will perhaps be necessary to stay it, according to the laws in
force (you should seek professional advice). All PRESIDENT antennas and
accessories are designed to give maximum efficiency to each CB radio
within the range.
3) POWER CONNECTION
Your PRESIDENT WALKER II FCC is protected against an inversion of polarities.
However, before switching it on, you are advised to check all the connec-
tions. Your equipment must be supplied with a continued current of 12 volts
(A). Today, most cars and lorries are negative earth. You can check this by
making sure that the negative terminal of the battery is connected either to
the engine block or to the chassis. If this is not the case, you should consult
your dealer.
WARNING: Trucks generally have two batteries and an electrical installation
of 24 volts, in which case it will be necessary to insert a 24/12 volt converter
(type CV 24/12 PRESIDENT) into the electrical circuit. The following connec-
tion steps should be carried out with the power cable disconnected from
the set.
a) Check that the battery is of 12 volts.
b) Locate the positive and negative terminals of the battery (+ is red and - is
black). Should it be necessary to lengthen the power cable, you should
use the same or a superior type of cable.
c) It is necessary to connect your transceiver to a permanent (+) and (-).
We advise you to connect the power cable directly to the battery (as the
connection of the transceiver cable to the wiring of the car-radio or other
parts of the electrical circuit may, in some cases, increase the likelihood of
interference).
d) Connect the red wire (+) to
the positive terminal of the
battery and the black (-) wire
to the negative terminal of the
battery.
e) Connect the power cable to
your CB radio.
WARNING: Never replace the
original fuse by one of a differ-
ent value.
4) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING YOUR
SET FOR THE FIRST TIME (without transmitting and without
using the “push-to-talk” switch on the microphone)
a) Connect the microphone.
b) Check the antenna connections.
c) Turn the set on by turning the VOLUME knob (1) clockwise.
d) Turn the SQUELCH knob (2) to minimum M.
e) Adjust the volume to a comfortable level.
f) Go to channel 20 by using rotary PUSH knob (6) or UP/DN buttons (18) on
the microphone.
5) HOW TO ADJUST SWR (Standing Wave Ratio)
Warning: This must be carried out when you use your radio for the first time
and whenever you re-position your antenna. This adjustment must be car-
ried out in an obstacle-free area.
* Adjustment with internal SWR-meter
NEW, EASY AND VERY HANDY- Adjustment of SWR meter by beep tones
See menu SWR ADJUSTMENT function page 12.
English
7
* Adjustment with external SWR-meter (e.g. TOS-1 PRESIDENT)
a) To connect the SWR meter :
- Connect the SWR meter between the CB radio and the antenna as close as
possible to the CB (use a maximum of 15.75 in / 40 cm cable, type President
CA 2C).
b) To adjust the SWR meter:
- Set the CB on channel 20.
- Put the switch on the SWR-meter to position FWD (calibration).
- Press the PTT “push-to-talk” switch (17) on the microphone to transmit.
- Bring the index needle to by using the calibration key.
- Change the switch to position REF (reading of the SWR level). The reading on
the Meter should be as near as possible to 1. If this is not the case, readjust
your antenna to obtain a reading as close as possible to 1. (A SWR reading
between 1 and 1.8 is acceptable).
- It will be necessary to recalibrate the SWR meter after each adjustment of
the antenna.
WARNING: In order to avoid any losses and attenuations in cables used for
connection between the radio and its accessories, PRESIDENT recommends
to use a cable with a length inferior to 118.11 in / 3 m).
Your transceiver is now ready for use.
B) HOW TO USE YOUR TRANSCEIVER
1) ON/OFF ~ VOLUME
Turn on : turn VOLUME knob (1) clockwise. If the function KEY BEEP is active
(see menu KEY BEEP page 10), the radio emits a beep. The radio is “on”.
Display shows the microphone type setup during 1 second . See menu MIC
TYPE page 12.
Turn Off : turn VOLUME knob (1) counterclockwise until radio emits click
sound. Your radio is “off”.
Volume Adjustment: rotate VOLUME knob (1) clockwise to adjust volume.
Turn the same knob counterclockwise to reduce the sound level.
2) ASC (Automatic Squelch Control) ~ SQUELCH
Suppresses undesirable background noises when there is no communication.
Squelch does not affect neither sound nor transmission power, but allows a
considerable improvement in listening comfort.
a) ASC: AUTOMATIC SQUELCH CONTROL
Worldwide patent, a PRESIDENT exclusivity
Turn the SQUELCH knob (2) anti-clockwise into ASC position.
appears
on LCD. No repetitive manual adjustment and a permanent improvement
between the sensitivity and the listening comfort when ASC is active. This
function can be disconnected by turning the switch clockwise. In this case
the squelch adjustment becomes manual again.
disappears from LCD.
b) MANUAL SQUELCH
Turn the SQUELCH knob (2) clockwise to the exact point where all background
noise disappears. This adjustment should be done with precision as, if set to
maximum (fully clockwise), only the strongest signals will be received.
3) RF POWER
In TX mode, turn the RF POWER knob (3) to adjust the transmission power;
clockwise to increase, counterclockwise to decrease the RF POWER.
4) MIC GAIN
Adjustment of the sensitivity level of the microphone.
The normal position of this function is set to maximum clockwise.
5) RF GAIN
Adjustment of the reception sensitivity. Maximum position in the case of long-
distance transmission. You can decrease the RF GAIN, to avoid distortions,
when the interlocutor is near. Reduce the gain on reception in the case of a
close communication with a correspondent not equipped with a RF POWER.
The normal position of this function is at maximum clockwise.
6) ROTARY “PUSH” KNOB
In normal operation, turn rotary PUSH knob (6) to adjust channel. Clockwise
to increase, counterclockwise to decrease the channel.
In MENU mode (long press PUSH knob (6) for 3 seconds to activate this
mode). See § MENU page 10.
1. Turn rotary PUSH knob (6) to select the function to set.
2. Press PUSH knob (6) to validate. The parameter of the chosen function blinks
on LCD.
3. Turn rotary PUSH knob (6) to change the value of the parameter.
4. New press PUSH knob (6) to validate the chosen value. The parameter
stops blinking and if the function has more than one parameter, the next
parameter blinks.
See § UP/DN BUTTONS ON THE MICROPHONE page 9.
English
8
7) LCD
Indicates transmission
PA PA (Public Address) mode activated
AM AM modulation
ROGER BEEP function activated
BP KEY BEEP function activated
Automatic Squelch Control activated
VOX VOX function activated
SCAN function activated (the dot blinks)
TALKBACK TALKBACK function activated
MENU mode activated
Indicates selected channel (large digits)
The Weather Channel mode is activated
ALERT function is activated
Indicates frequency or menu
8) VOX ~ VOX SET
VOX
(short press)
The VOX function allows transmitting by speaking into the original micro-
phone (or in the optional vox microphone) without pressing the PTT switch
(17). The use of an optional vox microphone connected to the rear panel
of the transceiver (E) disables the original microphone.
Press shortly VOX key (8) in order to activate the VOX function. “VOX”
appears on the display. Press shortly again the VOX key (8) to disable the
function. “VOX” disappears.
VOX SET (long press)
Press the VOX key (8) for 2 seconds in order to activate the VOX Adjustment
mode.
Three adjustments are possible: Sensitivity SET L / Anti-vox level SET A / Vox
delay time SET T (over and over).
1. To change a setting other than the one displayed, press the VOX key (8)
to select the next setting or...
2. Turn the rotary PUSH knob (6) or press the UP/DN (18) keys on the microphone
to modify the setting.
3. Press again the VOX key (8) to store and move to next setting...
4. Once the settings done, press the PTT switch (17) key to exit the VOX Adjust-
ment mode. If no adjustment is made for 5 seconds, the unit automatically
exits the function.
- Sensitivity SET L: allows the adjustment of the microphone (original one or
optional vox) for an optimum transmission quality. Adjustable level from1
(high level) to 9 (low level).Default value: 5.
- Anti-Vox SET A: allows disabling the transmission generated by the surround-
ing noise. The level is adjustable. 0 (Off) and from 1 (hign level) to 9 (low
level). Default value: 9.
- Delay time SET T: allows avoiding the sudden cut of the transmission by
adding a delay at the end of speaking. The level is adjustable from 1 (short
delay) to 9 (long delay). Default value; 1.
9) TALKBACK
This function allows you to hear your own modulation in the optional internal
or external speaker connected to the EXT jack. MS. (C).
Press the TALKBACK key (9) to activate/deactivate the TALKBACK function.
When the function is active, “TALKBACK” flashes in the LCD for 3 seconds,
displaying the current level of the TALKBACK, and remains then permanently
displayed. See § TALKBACK LEVEL page 12.
10) NB/ANL - HIC FILTERS
3 positions switch: Low position: no filter is activated. Central position: only
ANL and NB filters are enabled. High position: all filters (ANL, NB and HI-CUT)
are activated.
NB: Noise Blanker / ANL: Automatic Noise Limiter. These filters allow reducing
back ground noises and some reception interferences.
HI-CUT: Cuts out the high frequency interferences and has to be used in
accordance with the reception conditions.
English
9
11) PRIORITY CHANNELS
Priority channels will be automatically selected by switching this key (11).
3 positions switch: EMG1/ Priority channel 1 is activated. EMG2 / Priority
channel 2 is activated. OFF / No priority channel is activated.
The default priority channels are channel 9 (EMG1) and channel 19 (EMG2).
See the EMG SET 1 and EMG SET 2 menus page 11 to set priority channels.
Note: Activating a priority channel no longer allows you to use the PA or WX
modes, or to start the SCAN function. if the KEY BEEP function is active, an
error beep is emitted. “EMG” and the channel blink to indicate unauthorized
handling. Turn the switch (11) to the OFF position to use these functions.
12) CB/PA
Switch between CB and PA (Public Address) mode.
An external optional speaker can be connected to the unit to the PA.SP.
jack on the rear panel. (D). Turn the MIC GAIN knob (4) to adjust the PA
volume.
For details on operating in PA mode, see the PA SETTING menu on page
12.
13) WX MODE ~ ALERT
WX MODE
(short press)
Note: CB functions are not allowed in WX mode. If a user presses a not al-
lowed key when the KEY BEEP function is activated, the radio sounds an error
tone.
Select a channel other than the EMG1 or EMG2 emergency channels. The
PRIORITY CHANNEL switch (11) must be in the OFF position. Press briefly the
WX key (13) to alternate between CB and WX modes. When WX mode is
active, “WX” is displayed. WX mode allows you to listen to weather reports.
When this mode is turned on, turn the rotary PUSH knob (6) or use the UP/DN
(18) keys on the microphone to search, through the 7 weather channels,
for the channel corresponding to your location (See WEATHER FREQUENCY
TABLE page 55).
The display shows the selected channel.
ALERT (long press)
Note: The SIREN tone only sounds in PA or CB mode. It does not sound in
WX mode.
Long press the ALERT key (13), to activate/deactivate the ALERT function.
When the function is activated the last digit of frequency becomes A
(
). If the function is activated and a tone is detected at
the selected weather channel, then the unit sounds “SIREN” tone. The unit
cancels CB or PA mode and goes to WX mode.
During a SIREN tone sound, press PTT key (17) to stop the sound.
14) BARGRAPH
Indicates the reception level and the emitted power level.
15) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 56.
16) USB CHARGING SOCKET
The USB socket (16) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
17) PTT
Transmission key, press to transmit a message,
is displayed and release
to listen to an incoming communication,
disappears.
TOT (Time Out Timer)
If the PTT switch (17) key is pressed for more than 5 minutes, the display starts
blinking and the transmission ends. A beep will sound until the PTT switch
(17) key is released.
18) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
(short press)
In normal use, press UP/DN buttons (18) on the microphone to change the
channel. UP to increase and DN to decrease the channel.
In MENU mode [press the PUSH knob (6) for about 3 seconds to activate this
mode (see § MENU page 10)], the UP or DN buttons (18) allows to select
the menu to be set.
See ROTARY “PUSH” KNOB page 7.
English
10
SCAN (long press)
Press and hold the UP or DN button (18) to activate the SCAN function. The
dot between the two channel digits flashes to indicate that the function is
active.
The scanning stops as soon as there is a busy channel. The scanning auto-
matically starts 3 seconds after the end of the transmission and if no key is
activated during 3 s. In SCANNING mode, turn the PUSH rotary knob (6) or
press the UP/DN buttons (18) on the microphone to change scan direction.
CB channel Scan
In CB mode press for ± 7 seconds or until a beep sounds to activate the CB
channel Scan.
Press PTT switch (17) to exit CB Channel Scan. The dot between the two
channel digits disappears from LCD.
WX channel Scan
In WX mode press for ± 3 seconds or until a beep sounds to activate the
WX channel Scan.
Press for 3 seconds the TALKBACK key (9) to exit WX Channel Scan. The dot
between the two channel digits disappears from LCD.
Note: The WX channel scan can run in the background while using the CB
mode.
A) DC-POWER TERMINAL (13,8 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
D) JACK FOR PA OPTIONAL SPEAKER (Public Address) (8 Ω,
Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (8 Ω,Ø 2.5 mm)
C) MENU
The order of 11 functions is as described in this manual. However, the func-
tion displayed by entering the MENU will be the last function modified by
user.
The procedure is the same whatever the function is:
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the menu.
2. Press PUSH knob (6) to validate. The parameter of the chosen function blinks
on the display.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to modify the value of the parameter.
4. New press PUSH knob (6) to validate the chosen value. The parameter
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5. If no key is pressed, the unit exits MENU after 10 seconds.
disappears from
the display.
Note: UP/DN buttons (18) on the microphone have the same effect as the
rotation of the rotary PUSH knob (6). PTT switch (17) validates the last setting
and exists MENU.
disappears.
1) COLOR
This function allows to choose the backlight color of the LCD.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the COLOR function.
2. Press PUSH knob (6) to validate. The current color blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (11) on the microphone
to select the color. 7 available colors are displayed over and over :
4. New press PUSH knob (6) to validate the chosen color. The color stops
blinking. a) Go back to point 1 to adjust another function or b) Press the
PTT switch (17) to validate and exit MENU. disappears in the display.
5. If no key is pressed, the unit exits MENU after 10 seconds, disappears in
the display.
Default COLOR is
(red).
2) KEY BEEP
When the function is activated, a beep sounds when a key is pressed, by
changing the channel etc. “BP” appears on the display when the function
is active.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the KEyBEEP function.
2. Press PUSH knob (6) to validate. The current status blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to activate On / deactivate Of the function.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU. disappears.
English
11
5. If no key is pressed, the unit exits MENU after 10 seconds,
disappears in
the display.
Default KEY BEEP is On.
3) ROGER BEEP
When the function is active, the icon
appears on the display.
The Roger Beep sounds when the PTT switch (17) on the microphone is re-
leased in order to let your correspondent speak. Historically as transceiver
is a “simplex” communication mode, it is not possible to speak and to listen
at the same time (as it is the case with a telephone). Once someone had
finished talking, he said “Roger” in order to prevent his correspondent that
it was his turn to talk. The word “Roger” has been replaced by a significant
beep. There comes “Roger beep” from.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the RG BP function.
2. Press PUSH knob (6) to validate. The current status blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to activate On / deactivate Of the function.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU. disappears.
5. If no key is pressed, the unit exits MENU after 10 seconds, disappears in
the display.
Default ROGER BEEP is Of.
4) TONE
The TONE function is used to change the tone on reception. 11 levels from
-5 to +5.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the TONE function.
2. Press PUSH knob (6) to validate. The value of the tone blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select a new value.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU. disappears.
5. If no key is pressed, the unit exits MENU after 10 seconds, disappears in
the display.
Default TONE is 0.
5) DIMMER
The DIMMER function allows to adjust the brightness (from 1 to 9) of the
backlight or to set no backlight (OF).
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the DIMMER function.
2. Press PUSH knob (6) to validate. The value of the dimmer blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select a new value.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU. disappears.
5. If no key is pressed, the unit exits MENU after 10 seconds, disappears in
the display.
Default DIMMER value is 9.
6) EMG SET 1
Allows to set the Priority Channel 1.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the EMG 1 function.
2. Press PUSH knob (6) to validate. The channel blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the channel.
4. New press PUSH knob (6) to validate. The channel stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU. disappears.
5. If no key is pressed, the unit exits MENU after 10 seconds, disappears in
the display.
Default Priority channel 1 is 9.
See § PRIORITY CHANNELS page 9.
7) EMG SET 2
Allows to set the Priority Channel 2.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the EMG 2 function.
Points 2 to 5 are identical to § EMG SET 1.
Default Priority channel 2 is 19.
See § PRIORITY CHANNELS page 9.
English
12
8) SWR ADJUSTMENT
This function allows to adjust the SWR (Standing Wave Ratio) by beep tones.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use the UP/DN buttons (18) on the micro-
phone to select the SWR function.
2. Press the rotary PUSH knob (6). The radio automatically goes to TX mode
without pressing PTT switch (17) . The SWR measurement starts. Measurement
time is 5 minutes maximum. The remaining time is displayed.
3. Adjust your antenna.
4. The beep tone* is continuous when SWR value is equal to 1.0. The space
between two beeps became longer when SWR value moves away from1.0.
Display shows the SWR value. For example 2.5.
5. Press PTT switch (17) to exit MENU mode. disappears in the display.
*Volume of the beep tone is adjustable with VOLUME knob (1). Please check
that the beep volume is set to a comfortable listening level.
See § HOW TO ADJUST SWR page 6.
9) MIC TYPE
The PRESIDENT WALKER II FCC can be used with an electret microphone as
well as with the dynamic one, 6-pin PRESIDENT (see the cabling diagram
page 56). Turning on the unit, the type of the microphone is briefly dis-
played.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the MIC TP function.
2. Press PUSH knob (6) to validate. The current parameter blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the type on the microphone EL (electret) or DY (dynamic).
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU. disappears.
5. If no key is pressed, the unit exits MENU after 10 seconds, disappears in
the display.
Default type of microphone is EL
(electret).
10) PA SETTING
This function allows to select the operating mode of Public Address.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the PA SET function.
2. Press PUSH knob (6) to validate. The current value blinks on LCD.
3. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the operating mode of the PA : In , OF or PA.
4. New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to adjust another function or b) Press the PTT switch (17) to
validate and exit MENU.
disappears.
5. If no key is pressed, the unit exits MENU after 10 seconds, disappears in
the display.
In : the modulation of the microphone is transmitted to the external loud-
speaker connected to jack PA.SP. (D). The received signal is transmitted to
the internal loudspeaker [or external optional loudspeaker connected to
jack EXT.SP (C)]. “PA” blinks alternately with the modulation mode (AM).
OF: The reception is no more functional. Only the modulation of the micro-
phone is transmitted to the Public Address loudspeaker connected to jack
PA.SP. (D). PA and PA volume level are displayed.
PA: the modulation of the microphone and the received signal are transmit-
ted to the Public Address loudspeaker connected to jack PA.SP. (D). PA
MODE: “PA” blinks alternately with the modulation mode (AM).
The MIC GAIN knob (4) to adjust the audio level of the mode PA.
Default PA setting is: In .
See § PA (Public Address) page 9.
11) RESET
Restores all factory settings.
Press PUSH knob (6) for 3 seconds to enter MENU.
is displayed.
1. Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to select the RESET function.
2. Press PUSH knob (6) to validate. AL blinks on LCD.
3. New press PUSH knob (6) to reset. The unit exits MENU. disappears.
4. If no key is pressed, the unit exits MENU after 10 seconds or by a new long
press on PUSH knob(6) key.
D) FUNCTION WITH PTT SWITCH
TALKBACK LEVEL
This function allows to adjust the volume level of the TALKBACK.
1. Activate the TALKBACK function (see § TALKBACK page 8).
2. Press and hold the PTT switch (17) then turn the rotary PUSH knob (6) to
increase (clockwise) / decrease (counterclockwise) the volume level of
the TALKBACK.
3. Release the PTT switch (17).
English
13
E) TECHNICAL CHARACTERISTICS
1) GENERAL
- Channels : 40
- Modulation modes : AM
- Frequency range : from 26.965 MHz to 27.405 MHz
- Weather channels : from162,400 MHz to 162,550 MHz
- Antenna impedance : 50 ohms
- Power supply : 13.8 V
- Dimensions : 6.692 (W) x 6.299 (D) x 2.047 (H) inches
: 170 (W) x 160 (D) x 52 (H) mm
- Weight : ± 2.43 lbs / 1.1 kg
- Accessories supplied : 1 microphone electret UP/DOWN with
support, mounting cradle, screws and
fused power cord.
2) TRANSMISSION
- Frequency allowance : +/- 200 Hz
- Carrier power : 4 W
- Transmission interference : inferior to 4 nW (- 54 dBm)
- Audio response : 300 Hz to 3 KHz
- Emitted power in the adj. channel : inferior to 20 µW
- Microphone sensitivity : 3.0 mV
- Drain : < 2 A max. (with modulation)
- Modulated signal distortion : 1,8 %
3) RECEPTION
- Maxi. sensitivity at 20 dB sinad : 0.5 µV - 113 dBm
- Frequency response : 300 Hz to 3 kHz
- Adjacent channel selectivity : 60 dB
- Maximum audio power : 3 W
- Squelch sensitivity : minimum 0.2 µV - 120 dBm
maximum 1 mV - 47 dBm
- Frequency image rejection rate : 60 dB
- Intermediate frequency rej. rate : 70 dB
- Drain : 180 ~ 500 mA maximum
F) TROUBLE SHOOTING
1) YOUR RADIO WILL NOT TRANSMIT OR YOUR TRANSMISSION
IS OF POOR QUALITY
- Check that the antenna is correctly connected and that the SWR is properly
adjusted.
- Check that the microphone is properly plugged in.
- Check that the RF POWER value is set on maximum. (See § RF POWER page
7).
- Check that the MIC GAIN value is set on maximum. (See § MIC GAIN page
7).
2) YOUR RADIO WILL NOT RECEIVE OR RECEPTION IS POOR
- Check that the squelch level is properly adjusted.
- Check that the volume (1) is set to a comfortable listening level.
- Check that the antenna is correctly connected and that the SWR is properly
adjusted.
- Check that the RF GAIN level is set on maximum. (See § RF GAIN page
7).
3) YOUR RADIO WILL NOT LIGHT UP
- Check the power supply.
- Check the connection wiring.
- Check the fuse.
G) HOW TO TRANSMIT OR RECEIVE A MESSAGE ?
Now that you have read the manual, make sure that your CB Radio is ready
for use (i.e. check that your antenna is connected).
Press the «push-to-talk» switch (17) and announce your message «Attention
stations, transmission testing» which will allow you to check the clearness
and the power of your signal. Release the switch and wait for a reply. You
should receive a reply like, «Strong and clear».
If you use a calling channel (19) and you have established communication
with someone, it is common practice to choose another available channel
so as not to block the calling channel.
H) GLOSSARY
INTERNATIONAL PHONETIC ALPHABET
A Alpha H Hotel O Oscar V Victor
B Bravo I India P Papa W Whiskey
C Charlie J Juliett Q Quebec X X-ray
D Delta K Kilo R Romeo Y Yankee
E Echo L Lima S Sierra Z Zulu
F Foxtrott M Mike T Tango
G Golf N November U Uniform
English
14
TECHNICAL VOCABULARY
AM : Amplitude Modulation
CB : Citizen’s Band
CH : Channel
CW : Continuous Wave
DX : Long Distance Liaison
DW : Dual Watch
FM : Frequency Modulation
GMT : Greenwich Meantime
HF : High Frequency
LF : Low Frequency
LSB : Lower Side Band
RX : Receiver
SSB : Single Side Band
SWR : Standing Wave Ratio
SWL : Short Wave Listening
SW : Short Wave
TX : CB Transceiver
UHF : Ultra High Frequency
USB : Upper Side Band
VHF : Very High Frequency
CB LANGUAGE
Advertising : Flashing lights of police car
Back off : Slow down
Basement : Channel 1
Base station : A CB set in fixed location
Bear : Policeman
Bear bite : Speeding fine
Bear cage : Police station
Big slab : Motorway
Big 10-4 : Absolutely
Bleeding : Signal from an adjacent chan-
nel interfering with the trans-
mission
Blocking the channel : Pressing the PTT switch without talking
Blue boys : Police
Break : Used to ask permission to join
a conversation
Breaker : A CBer wishing to join a channel
Clean and green : Clear of police
Cleaner channel : Channel with less interference
Coming in loud and proud : Good reception
Doughnut : Tyre
Down and gone : Turning CB off
Down one : Go to a lower channel
Do you copy? : Understand?
DX : Long distance
Eighty eights : Love and kisses
Eye ball : CBers meeting together
Good buddy : Fellow CBer
Hammer : Accelerator
Handle : CBer’s nickname
Harvey wall banger : Dangerous driver
How am I hitting you? : How are you receiving me?
Keying the mike : Pressing the PTT switch without
talking
Kojac with a kodak : Police radar
Land line : Telephone
Lunch box : CB set
Man with a gun : Police radar
Mayday : SOS
Meat wagon : Ambulance
Midnight shopper : Thief
Modulation : Conversation
Negative copy : No reply
Over your shoulder : Right behind you
Part your hair : Behave yourself - police ahead
Pull your hammer back : Slow down
Rat race : Congested traffic
Rubberbander : New CBer
Sail boat fuel : Wind
Smokey dozing : Parked police car
Smokey with a camera : Police radar
Spaghetti bowl : Interchange
Stinger : Antenna
Turkey : Dumb CBer
Up one : Go up one channel
Wall to wall : All over/everywhere
What am I putting to you? : Please give me an S-meter
reading
English
15
If you note a malfunction:
• Check the power supply of your device and the quality of the fuse.
• Check that the antenna, the microphone are correctly connected.
• Check that the squelch level is properly adjusted; the programmed configuration is the
correct one.
• In the event of a real malfunction, please contact your dealer first. He will decide what
action should be taken.
In case of an intervention not covered by warranty, an estimate will be established before
any repair.
Thank you for your confidence in the PRESIDENT quality and experience. We recommend
that you read this manual carefully so that you are completely satisfied with your purchase.
Technical Manager
and
Quality Manager
GENERAL WARRANTY CONDITIONS
This device is guaranteed 2 years parts and labour in its country of purchase against
any manufacturing defects validated by our technical department. PRESIDENT After Sales
Service department reserves the right not to apply the warranty in the event a breakdown
is caused by an antenna other than those distributed by PRESIDENT. An extension of 3
years warranty is proposed systematically for the simultaneous purchase of a device and
a PRESIDENT antenna, bringing the total duration of the warranty to 5 years. In order to
be valid, the warranty registration must be completed and submitted within a period of 30
days after the purchase date to PRESIDENT ELECTRONICS online at
www.president-
electronics.us/warranty-registration
. You can also access this warranty registration
page by using your smartphone to read (application must be available) the QR code on the
enclosed warranty card. You will receive a confirmation email if the registration is successfully
completed. Please keep a copy of this email for your records.
Any repair under warranty will be without charge and the return delivery costs will be borne
by PRESIDENT. A proof of purchase sales receipt must be included with the device to be
repaired. The dates listed on the warranty registration and proof of purchase must match.
In case the device is not under warranty, the repair and return of the device will be charged.
No spare parts will be sent nor exchanged by PRESIDENT under warranty. Do not proceed
with the installation of the device without reading the user manual.
The warranty is only valid in the country of purchase.
Exclusions (not covered by Warranty):
• Damages caused by accident, shock or inadequate packaging.
• Power transistors, microphones, lights, fuses and the disrespect of the installation and use
of specifications (including but not limited to antenna used with too high power, final output
power transistors (SWR), inversion of polarities, bad connections, over voltage…).
• The warranty cannot be extended due to the non-availability of the device while it is being
serviced at PRESIDENT After Sales Service department, nor by a change of one or more
components or spare parts.
• Transceivers which have been modified. The warranty application is excluded in case
of modification or poor maintenance done by a third party not approved by PRESIDENT
ELECTRONICS.
English
16
La garantía de este artículo sólo es válida en el país de compra.
¡ ATENCIÓN !
Antes de la utilización tengan cuidado de
nunca emitir sin haber previamente conec-
tado la antena (conector “B” situado en la
parte trasera de su equipo), ajustada la ROE
(Relación de Ondas Estacionarias)! Sino, se
expone a dañar el amplificador de potencia,
no cubierto por la garantía.
Español
WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
17
Bienvenido al mundo de los emisores-receptores CB de última generación. Esta
nueva gama de estaciones le permite acceder a la comunicación electrónica
más competitiva. Gracias a la utilización de tecnología punta que garantiza
una calidad sin precedentes, su PRESIDENT WALKER II FCC ASC representa un
nuevo hito en la facilidad de uso y la solución por excelencia para el usuario
más exigente de CB. Para sacar el máximo partido de todas sus posibilidades,
le aconsejamos leer atentamente estas instrucciones de uso antes de instalar
y utilizar su CB PRESIDENT WALKER II FCC ASC.
A) INSTALACIÓN
1) ELEGIR EL EMPLAZAMIENTO Y MONTAJE DEL PUESTO MÓVIL
a) Escoja el emplazamiento más apropiado para una utilización simple y
práctica de su estación móvil.
b) Procure que no moleste ni al conductor ni a los pasajeros del vehículo.
c) Prevea el paso y la protección de los diferentes cables, (alimentación,
antena, accesorios) con el fin de que en ningún caso perturben la con-
ducción del vehículo.
d) Utilice para el montaje el soporte (1) entregado con el aparato, fíjelo
sólidamente con ayuda de los tornillos auto-roscantes (2) proporcionados
(diámetro de agujero de 3,2 mm / 1.126"). Tenga cuidado de no dañar el
sistema eléctrico del vehículo en el momento del taladro del salpicadero.
e) En el momento del montaje, no se olvide de insertar las arandelas de
caucho (3) entre la estación y su soporte. Éstas tienen, en efecto, un papel
“amortiguador” y permiten una orientación y presión suaves de la estación.
f) Escoja un emplazamiento para el soporte del micro y prevea el paso de
su cable.
- NOTA: Su estación móvil que posee una toma de micro en la parte frontal
puede ser empotrada en el cuadro de mandos. En ese caso, se recomienda
añadirle un altavoz externo para una mejor escucha de las comunicaciones
(conector EXT.SP situado en la cara posterior del aparato: C). Infórmese
con su vendedor más próximo para el montaje en su aparato.
2) INSTALACIÓN DE LA ANTENA
a) Elección de la antena
- En CB, cuanto más grande es una antena, mejor es su rendimiento. Su
Centro de Asesoramiento sabrá orientarle en su elección.
b) Antena móvil
- Hay que instalarla en un lugar del vehículo donde haya un máximo de
superficie metálica (plano de masa), alejándose de los montantes del
parabrisas y de la luneta trasera.
- En caso de que se haya instalado una antena de radio-teléfono, la antena
CB debe estar por encima de ésta.
- Existen 2 tipos de antenas: las preajustadas y las regulables.
Español
18
- Las preajustadas se utilizan preferentemente con un buen plano de masa
(en el techo o en el maletero).
- Las regulables ofrecen un campo de uso mucho más extenso y permiten
sacar partido de planos de masa menos importantes (véase § AJUSTE DE
LA ROE página 18).
- Para una antena de fijación por taladro, es necesario tener un contacto
excelente entre la antena y el plano de masa; para ello, rasque ligeramente
la chapa al nivel del tornillo y de la estrella de presión.
- En el momento del paso del cable coaxial, tenga cuidado de no pelliz-
carlo ni aplastarlo (riesgo de rotura o cortocircuito).
- Conecte la antena (B).
a) Asegúrese de que la alimentación sea de 12 voltios.
b) Localice los bornes (+) y (-) de la batería (+ = rojo, - = negro). En caso de
que sea necesario alargar el cable de alimentación, utilice un cable de
sección equivalente o superior.
c) Es necesario conectarse a un (+) y un (-) permanentes. Le aconsejamos
pues, que conecte directamente el cable de alimentación a la batería
(el acoplamiento al cable de la auto-radio o a otras partes del circuito
eléctrico pueden, en ciertos casos, favorecer la recepción de señales
parásitas).
d) Conecte el hilo rojo (+) al borne
positivo de la batería y el hilo
negro (-) al borne negativo de
la batería.
e) Conecte el cable de alimen-
tación a la estación.
ATENCIÓN: ¡Nunca reempla-
ce el fusible de origen por un
modelo de un valor diferente!
4) OPERACIONES DE BASE QUE HAY QUE EFECTUAR ANTES
DE LA PRIMERA UTILIZACIÓN, SIN PASAR POR EMISIÓN (sin
apretar la palanca del micro)
a) Conecte el micro,
b) Verifique la conexión de la antena,
c) Puesta en marcha del aparato: gire el botón del volumen VOLUME (1) en
el sentido de las agujas del reloj hasta oír un “clic”,
d) Gire el botón del squelch SQUELCH (2) al mínimo, en la posición M,
e) Ajuste el volumen (1) a un nivel conveniente,
f) Dirija la estación al canal 20 con ayuda del conmutador rotativo PUSH (6)
o de los botones UP/DN (17) del micrófono.
5) AJUSTE DE LA ROE (Relación de Ondas Estacionarias)
ATENCIÓN: Esta operación debe efectuarse necesariamente en el momento
de la primera utilización del aparato o en el momento de un cambio de
antena. Este ajuste debe se realizar en un lugar abierto, al aire libre.
* Ajuste con el medidor de ROE integrado
NUEVO, FÁCIL Y MUY ÚTIL - ajuste mediante “pitidos”
Véase le menú AJUSTE DE LA ROE página 24.
Lóbulo de radiación
c) Antena fija
- Procure abrirla al máximo. En caso de fijación sobre un poste, habrá que
sostenerla eventualmente conforme a las normas vigentes (infórmese con
un profesional). Las antenas y los accesorios PRESIDENT han sido especial-
mente concebidos para un rendimiento óptimo de todos los aparatos de
la gama.
3) CONEXIÓN DEL ALIMENTADOR
Su PRESIDENT WALKER II FCC ASC está provista de una protección contra
las inversiones de polaridad.
Vuestra emisora debe ser alimentada por una fuente de corriente conti-
nua de 12 voltios (A). Actualmente, la mayoría de los coches y camiones
funcionan con una conexión de masa negativa. Podemos asegurarnos
verificando que el borne (-) de la batería esté bien conectado al bloque
motor o al chasis. En el caso contrario, consulte a su vendedor.
ATENCIÓN: Los camiones poseen generalmente dos baterías y una insta-
lación eléctrica de 24 voltios. Será necesario pues intercalar en el circuito
eléctrico un convertidor de 24/12 voltios (Tipo PRESIDENT CV 24/12).
Las siguientes operaciones de conexión deben ser efectuadas con el cable
de alimentación no conectado a la estación:
Español
19
* Ajustes con el medidor de ROE externo (tipo TOS-1 PRESIDENT):
a) Empalme del medidor de ROE
- Conecte el medidor de ROE entre la estación y la antena, lo más cerca
posible de la estación (utilice para ello un cable de 40 cm / 15,75" máximo
tipo CA-2C PRESIDENT).
b) Ajuste de la ROE
- Posicione la estación hacia el canal 20.
- Sitúe el conmutador del medidor de ROE en posición FWD (calibración).
- Apriete la palanca PTT (17) del micro para pasar a emisión.
- Dirija la aguja al índice ▼ con ayuda del botón de calibración.
- Ponga el conmutador en posición REF (lectura del valor de la ROE). El valor leído
en el indicador debe estar muy cerca de 1. En caso contrario, reajuste su antena
hasta obtener un valor lo más cerca posible a 1 (puede aceptarse un valor de la
ROE comprendido entre 1 y 1,8).
- Es necesario recalibrar el medidor de ROE entre cada operación de ajuste
de la antena.
Observación: Con el fin de evitar las pérdidas y las atenuaciones en los
cables de conexión entre la radio y sus accesorios, PRESIDENT recomienda
una longitud de cable inferior a 3 m (118,11").
Ahora, su estación está preparada para funcionar.
B) UTILIZACIÓN
1) ENCENDIDO-APAGADO / VOLUMEN
Para encender la emisora: gire el botón VOLUME (1) hacia la derecha. Si
la función PITIDO DE TECLADO está activa (véase página 23), sonará un
pitido. Su radio está encendida “on”. La pantalla muestra brevemente el
tipo de micrófono (véase el menú TIPO DE MICRÓFONO página 24).
Para apagar el equipo: gire el botón VOLUME (1) hacia la izquierda hasta
que escuche un clic. Su radio está apagada “off”.
Para ajustar el volumen, gire el mando VOLUME (1) hacia la derecha. Para
disminuir el volumen, gire el mando en sentido antihorario.
2) ASC (Automatic Squelch Control) / SQUELCH
Esta función permite suprimir los ruidos de fondo indeseables en ausencia
de comunicación.
El squelch no actúa ni sobre el volumen sonoro ni sobre la potencia de
emisión, pero permite mejorar considerablemente la comodidad de es-
cucha.
a) ASC : SQUELCH CON AJUSTE AUTOMÁTICO
Patente mundial, exclusiva de PRESIDENT
Gire el botón del squelch SQUELCH (2) en el sentido contrario a las agujas del
reloj en la posición ASC.
aparece en el display. Evita el ajuste manual
repetitivo y permite la optimización permanente entre la sensibilidad y la
comodidad de escucha. Esta función puede desactivarse por rotación
del botón en el sentido de las agujas del reloj. En ese caso, el ajuste del
squelch vuelve a ser manual.
desaparece del display.
b) SQUELCH MANUAL
Gire el botón del squelch SQUELCH (2) en el sentido de las agujas del reloj
hasta el punto exacto en que desaparezca cualquier ruido de fondo.
Este ajuste debe efectuarse con precisión, porque, en posición máxima
en el sentido de las agujas del reloj, sólo las señales más fuertes pueden
ser percibidas.
3) RF POWER
En modo TX, gire el botón RF POWER (3) para ajustar la potencia de sali-
da; en el sentido de las agujas del reloj para aumentar la potencia, en el
sentido contrario a las agujas del reloj para disminuir la potencia.
4) MIC GAIN
Ajuste del nivel de sensibilidad del micrófono.
La posición normal de esta función está al máximo en el sentido de las
agujas del reloj.
5) RF GAIN
Configure la sensibilidad de recepción. Posición máxima en el caso de la
recepción de llamadas a larga distancia. Puede disminuir la ganancia de
RF, para evitar distorsiones, cuando el interlocutor esté cerca. Reduzca la
ganancia de recepción en el caso de una comunicación cercana con
un corresponsal que no esté equipado con RF POWER.
La posición normal de esta función está al máximo en el sentido de las
agujas del reloj.
6) CONMUTADOR ROTATIVO «PUSH»
En modo normal, gire el conmutador rotativo PUSH (6) para cambiar el
canal. Gire en el sentido de las agujas del reloj para aumentar y en sentido
antihorario para disminuir de un canal.
En el modo MENÚS (una presión de aproximadamente 3 segundos en el
botón PUSH (6) activa este modo). Véase § MENÚS página 22.
Español
20
1. Gire el botón rotativo PUSH (6) para seleccionar la función que se va a
configurar.
2. Presione brevemente el botón PUSH (6) para confirmar. El parámetro de
ajuste de la función seleccionada parpadea en la pantalla.
3. Gire el botón rotativo PUSH (6) para cambiar el valor del parámetro.
4. Presione el botón PUSH (6) nuevamente confirma el valor seleccionado. El
parámetro deja de parpadear y si la función tiene más de un parámetro,
el siguiente parámetro parpadea.
Véase § BOTONES UP/DN DEL MICRÓFONO página 22.
7) PANTALLA LCD
Indica la emisión
PA Modo PA (Public Address) activado
AM Modulación en AM
Función ROGER BEEP activada
BP Función PITIDO DEL TECLADO activado
Automatic Squelch Control activado
VOX Función VOX activada
Función SCAN activada (el punto parpadea)
TALKBACK Función TALKBACK activada
Modo MENÚS activado
Indica el canal seleccionado (dígitos grandes)
Modo CANALES METEOROLÓGICOS activado
Función ALERT activada
Indica la frecuencia y el menú
8) VOX ~ AJUSTE DEL VOX
VOX
(presión breve)
La función VOX permite emitir hablando en el micro de origen (o en el
micro vox opcional) sin apretar la palanca PTT (17). La utilización de un
micro vox opcional conectado detrás del aparato (E) desactiva el micro
de origen.
Apriete brevemente el botón VOX (8) para activar la función VOX. Aparece
en el visualizador el icono “VOX”. Una nueva presión en el botón VOX (8)
desactiva la función. El icono “VOX” desaparece de la pantalla.
AJUSTE DEL VOX (presión larga)
Pulse durante 2 segundos el botón VOX (8) para entrar en el modo AJUSTE
DEL VOX.
Tres parámetros permiten ajustar el VOX: Sensibilidad SET L, nivel Anti-Vox
SET A y la Temporización SET T.
1. Para cambiar un parámetro que no sea el que se muestra, presione bre-
vemente el botón VOX (8) para seleccionar el parámetro siguiente o ...
2. Gire el botón rotativo PUSH (6) o presione los botones UP/DN (18) del mi-
crófono para modificar el valor del parámetro...
3. Presione el botón VOX (8) para confirmar y pasar al parámetro siguiente.
4. Una vez que haya realizado la configuración, presione la palanca PTT
(17) para salir del modo de AJUSTE DEL VOX. Si no se realiza ningún ajuste
durante 5 segundos, la unidad sale automáticamente de la función.
- Sensibilidad “SET L”: ajusta la sensibilidad del micrófono (vox original o
opcional) para una calidad de transmisión óptima. Nivel ajustable de 1
(nivel alto) a 9 (nivel bajo). Valor predeterminado: 5.
- Anti-Vox «SET A»: evita la emisión generada por el ruido ambiental. Nivel
ajustable: 0 (OFF) y 1 (nivel alto) a 9 (nivel bajo). Valor predeterminado: 9.
- Temporización “SET T”: para evitar el corte “brutal” de la transmisión aña-
diendo un retraso al final del discurso. Nivel ajustable de 1 (retardo corto)
a 9 (retardo largo). Valor predeterminado: 1.
9) TALKBACK
Esta función le permite escuchar su propia modulación en el altavoz interno
[o el altavoz externo opcional conectado a la toma EXT. SP (C)].
Pulse la tecla TALKBACK (9) para activar/desactivar la función TALKBACK.
Cuando la función está activada, “TALKBACK” parpadea en la pantalla
durante 3 segundos, mostrando el nivel actual de TALKBACK y, a continua-
ción, permanece visualizado de forma permanente. Véase § TALKBACK
LEVEL página 25.
Español
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
PRESIDENT WALKER II FCC Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
PRESIDENT Walker 2 Le manuel du propriétaire
-
-
PRESIDENT Richard ASC Le manuel du propriétaire
-
-
-
-
-
-
-