EGO SNT2405 Le manuel du propriétaire

Catégorie
Souffleuses à neige
Taper
Le manuel du propriétaire
OPERATOR'S MANUAL
56-VOLT LITHIUM-ION
CORDLESS
SNOW BLOWER
MODEL NUMBER SNT2400/SNT2400-FC
WARNING: To reduce the risk of injury, the user must read and understand the
Operator’s Manual before using this product. Save these instructions for future reference.
Español p. 79
Français p. 39
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC2
TABLE OF CONTENTS
Safety Symbols ..........................................4
Safety Instructions ......................................5-6
Safe Operation Practices for Walk-behind Snow Blower .........6-9
Introduction ............................................10
Specications ..........................................10
Description .........................................11-13
Assembly ...........................................14-15
Operation ...........................................16-27
Maintenance ........................................28-33
Troubleshooting ......................................34-35
Warranty ...........................................36-37
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 3
READ ALL INSTRUCTIONS!
READ & UNDERSTAND
OPERATOR'S MANUAL
WARNING: Some dust created by power sanding, sawing, grinding, drilling
and other construction activities contains chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
Lead from lead-based paints
Crystalline silica from bricks and cement and other masonry products, and
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to lter out microscopic particles.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC4
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention to possible dangers. The
safety symbols and the explanations with them deserve your careful attention and
understanding. The symbol warnings do not, by themselves, eliminate any danger.
The instructions and warnings they give are no substitutes for proper accident
prevention measures.
WARNING: Be sure to read and understand all safety instructions in this
Operator’s Manual, including all safety alert symbols such as DANGER,” “WARNING,”
and “CAUTION before using this tool. Failure to follow all instructions listed below may
result in electric shock, re, and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION.
May be used in conjunction with other symbols or pictographs.
WARNING: The operation of any power tools can result in
foreign objects being thrown into your eyes, which can result in severe
eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields. Always use
eye protection which is marked to comply with ANSI Z87.1.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 5
SAFETY INSTRUCTIONS
This page depicts and describes safety symbols that may appear on this product.
Read, understand, and follow all instructions on the machine before attempting to
assemble and operate.
Safety Alert Indicates a potential personal injury hazard.
Eye Protection
Always wear safety goggles or safety glasses
with side shields and a full face shield when
operating this product.
Read Operator’s
Manual
To reduce the risk of injury, user must read
and understand operator’s manual before
using this product.
DANGER —
Keep Hands
Away from the
Impeller
Do not use hands to unclog the chute.
Keep Feet Out of
Impeller Keep feet away from rotating impeller
KEEP HANDS AND FEET AWAY
GARDER MAINS ET PIEDS À DISTANCE
MANTENGA LAS MANOS Y LOS PIES ALEJADOS
DANGER — Keep
Hands and Feet
Away
To reduce the risk of injury, keep hands and
feet away from rotating parts. Do not operate
unless discharge chute is in its proper place.
If damaged, replace immediately.
Recycle Symbols
This product uses Lithium-ion (Li-ion)
batteries. Local, state, or federal laws may
prohibit disposal of batteries in ordinary
trash. Consult your local waste authority for
information regarding available recycling and/
or disposal options.
IPX4 Ingress Protection
Degree Protection from splashing water
V Volt Voltage
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC6
Direct Current Type or a characteristic of current
cm centimeter Length or size
in. Inch Length or size
Ft. Feet Length or size
kg Kilogram Weight
lb Pound Weight
WARNING: To ensure safety and reliability, all repairs should be performed by a
qualied service technician.
SAFE OPERATION PRACTICES FOR WALK-BEHIND
SNOW BLOWER
DANGER: This snow blower is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety instructions could result in
serious injury.
FOR ALL SNOW BLOWERS
Do not use on graveled surface unless the snow blower is adjusted for such a
surface in accordance with the operator’s manual.
Keep Children Away – All visitors should be kept a safe distance from work area.
Dress Properly – Do not wear loose clothing or jewelry. They can be caught in
moving parts.
Wear rubber boots when operating the snow blower.
Keep hands away from moving parts.
Keep guards in place and in working order.
Don’t Force Snow Blower – It will perform better and safer at the rate for which it
was designed.
Don’t Overreach – Keep proper footing and balance at all times.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 7
If the snow blower strikes a foreign object follow these steps:
1) Stop snow blower. Release the switch.
2) Remove the battery pack(s).
3) Inspect for damage.
4) Repair any damage before restarting and operating the snow blower.
Store Idle Snow Blowers Indoors-When not in use, snow blowers should be stored
indoors in dry, locked-up place – out of reach of children.
Maintain Snow Blowers with Care – Following instructions for lubricating and
changing accessories.
TRAINING
Read, understand and follow all instructions on the machine and in the
manual(s) before operating this unit. Be thoroughly familiar with the controls and
the proper use of the equipment. Know how to stop the unit and disengage the
controls quickly.
Never allow children to operate the equipment. Never allow adults to operate the
equipment without proper instruction.
Keep the area of operation clear of all persons, particularly small children.
Exercise caution to avoid slipping or falling, especially when operating the snow
blower in reverse.
PREPARATION
Thoroughly inspect the area where the equipment is to be used and remove all
doormats, sleds, boards, wires, and other foreign objects.
Do not operate the equipment without wearing adequate winter garments. Avoid
loose-tting clothing that can get caught in moving parts. Wear footwear that will
improve footing on slippery surfaces.
Never attempt to make any adjustments while the motor is running (except when
specically recommended by manufacturer).
Always wear safety glasses or eye shields during operation or while performing
an adjustment or repair to protect eyes from foreign objects that may be thrown
from the machine.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC8
OPERATION
Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to battery pack, picking up or carrying the appliance. Carrying the
appliance with your nger on the switch or energizing appliance that have the
switch on invites accidents.
Do not put hands or feet near or under rotating parts. Keep clear of the discharger
opening at all times.
Exercise extreme caution when operating on or crossing gravel drives, walks, or
roads. Stay alert for hidden hazards or trafc.
After striking a foreign object, stop the motor, remove the battery pack(s),
thoroughly inspect the snow blower for any damage, and repair the damage
before restarting and operating the snow blower.
If the unit should start to vibrate abnormally, stop the motor and check
immediately for the cause. Vibration is generally a warning of trouble.
Stop the motor whenever you leave the operating position, before unclogging
the auger assembly housing or discharge chute, and when making any repairs,
adjustments or inspections.
When clearing, repairing or inspecting the snow blower, stop the motor and make
certain the auger assembly and all moving parts have stopped. Remove the
battery pack(s) to prevent someone from accidentally starting the motor.
Exercise extreme caution when operating on slopes.
Never operate the snow blower without proper guards and other safety protective
devices in place and working.
Never direct the discharge toward people or areas where property damage can
occur. Keep children and others away.
Do not overload the machine capacity by attempting to clear snow at too fast a
rate.
Disengage power to the auger assembly when snow blower is transported or not
in use.
Use only attachments and accessories approved by the manufacturer of the snow
blower (such as scraper bar).
Never operate the snow blower without good visibility or light. Always be sure of
your footing, and keep a rm hold on the handles. Walk; never run.
Do not expose a battery pack or tool to re or excessive temperature. Exposure to
re or temperature above 212 °F (100°C) may cause explosion.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 9
Use only with the battery packs and chargers listed below:
BATTERY PACK CHARGER
BA1400, BA1400-FC, BA2800, BA2800-FC,
BA4200, BA4200-FC, BA1400T, BA1400T-FC,
BA2240T, BA2240T-FC, BA2242T, BA2242T-FC,
BA2800T, BA2800T-FC, BA4200T, BA4200T-FC,
BA5600T, BA5600T-FC, BA6720T, BA6720T-FC
CH2100, CH2100-FC,
CH3200, CH3200-FC,
CH5500, CH5500-FC,
CH2800D, CH2800D-FC
CH7000, CH7000-FC
NOTICE: For best performance, recommend for use with 2pcs 5.0Ah or higher Ah batteries.
CLEARING A CLOGGING CHUTE
Hand contact with the rotating auger assembly inside the discharge chute is the most
common cause of injury associated with snow blowers. Never use your hand to clean
out the discharge chute.
To clear the chute:
SHUT THE MOTOR OFF!
Remove the battery pack(s) from the snow blower.
Wait 10 seconds to be sure the auger has stopping rotating.
Always use the chute clean tool which is attached to the machine as an
accessory, do not use your hand
MAINTENANCE AND STORAGE
Check all bolts or fasteners at frequent intervals for proper tightness to be sure
the equipment is in safe working condition.
Always refer to operator’s manual for important details if the snow blower is to be
stored for an extended period.
Maintain or replace safety and instruction labels, as necessary.
Run the machine a few minutes after blowing snow to prevent freeze-up of the
auger assembly.
SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others
who may use this tool. If you lend this tool to someone else, also lend these instructions
to them to prevent misuse of the product and possibly injury.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC10
INTRODUCTION
Congratulations on your selection of a new generation of 56V Lithium-Ion powered
snow blower. It has been designed, engineered and manufactured to give you the best
possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact EGO
customer service center 1-855-EGO-5656.
This manual contains important information on to the safe assembly, operation and
maintenance of your snow blower. Read it carefully before using the tool. Keep this
manual handy so you can refer to it at any time.
SERIAL NUMBER _____________________ DATE OF PURCHASE _________________
THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A LABEL ATTACHED ON AUGER
ASSEMBLY HOUSING.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE
PLACE FOR FUTURE REFERENCE. SAVE YOUR SALES RECEIPT.
SPECIFICATIONS
Voltage 56V
Clearing Width 24 in
Intake Height 20 in
Throwing Distance Up to 50 ft.
Wheel Size 15 in
Operating Temperature -4°F-50°F(-20°C-10°C)
Storage Temperature -4°F-158°F(-20°C-70°C)
Snow Blower Weight (Without battery pack) 143.3 lbs (65 kg)
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 11
DESCRIPTION
Battery Cover
1
Rear Handle
lnline Cable Adjuster
Side Rail
Main Handle
Main Handle
LED Light Button
Self-Propel Trigger
Safety Button
Auger-Speed-Control Lever
Self-Propel Speed-Control Lever
LED Sidelights
LED Indicator
Chute-Rotation Handle
Chute-Deector Handle
Auger-Switch Trigger
Chute Deector
Snow-Discharge Chute
Chute Clean Tool
Deck
LED Headlights
Skid Shoe
Battery
Compartment
Wheel
Scraper BarAuger
Electric Contacts
Battery-Release Button
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC12
WARNING: The safe use of this product requires an understanding of the
information on the tool and in this operator’s manual, as well as knowledge of the project
you are attempting. Before use of this product, familiarize yourself with all operating
features and safety rules.
Safety Button
The safety button must be pressed down before the motor can be started.
WARNING: The safety button is safety device. Never attempt to bypass its
operation.
Auger-Switch Trigger
Engages and disengages the motor. It can be working after pressing the safety button.
Auger-Speed-Control Lever
Adjusts the auger speed in order to adjust the throwing distance.
Self-Propel Trigger
Turns the self-propel function ON and OFF.
Self-Propel Speed-Control Lever
Increases or decrease the self-propel speed.
Chute-Rotation Handle
Rotates the chute so that the user may direct the discharged snow as desired. The
handle allows the chute to rotate from left 100° to right 100°.
Chute-Deector Handle
Adjusts the angle of the chute deector and the height of the discharge stream.
LED Headlights/Sidelights
This feature provides extra light for increased visibility.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 13
LED Light Button
Turns on/off the LED headlights and sidelights.
LED Indicator
Indicates the status of the snow blower and battery pack.
Scraper Bar
Removes the last bit of snow from the surface you are clearing.
Skid Shoe
Increases the ability to maneuver the snowblower on the snow and adjusts the distance
between snow scraper and ground.
Battery-Release Button
Press to release the battery quickly.
lnline Cable Adjuster
Loosen or Tighten the Snow-Discharge Chute
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC14
ASSEMBLY
WARNING: To prevent accidental starting that could cause serious personal
injury, always remove the battery pack(s) from the tool when assembling parts.
WARNING: If any parts are damaged or missing, do not operate this product
until the parts are replaced. Use of this product with damaged or missing parts could
result in serious personal injury.
WARNING: Do not attempt to modify this tool or create accessories not
recommended for use with this product. Any such alteration or modication is misuse
and could result in a hazardous condition leading to serious injury.
UNPACKING
Use two people to grasp the rear handle and the front part of the product at the
same time and carefully lift the tool up and out of the carton. Remove any other
accessories from the carton. Make sure that all items listed in the packing list are
included.
CAUTION: Heavy object. Team lift required. At least two persons are
required to be lift this snow blower out of the package.
WARNING: Do not use this product if any parts on the packing list are already
assembled to your product when you unpack it. Parts on this list are not assembled to
the product by the manufacturer and require customer installation. Use of a product
that may have been improperly assembled could result in serious personal injury.
Inspect the product carefully to make sure that no breakage or damage occurred
during shipping.
Do not discard the packing material until you have carefully inspected and
satisfactorily operated the tool.
If any parts are damaged or missing, please return the product to the place of
purchase.
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 15
LIST OF CONTENTS
PART NAME QUANTITY
Snow Blower 1
Snow-Discharge Chute Assembly 1
Handle Assembly 1
Operator’s Manual 1
Chute Clean Tool 1
Shear Pin 2
TO INSTALL THE HANDLE
ASSEMBLY
NOTICE: The handle assembly requires
assembly before operating the snow
blower (Fig.2).
1. Loosen the four locking knobs and
remove the four bolts from the rear
handle (Fig.3).
2. Lift the handle assembly, align
the holes in the side rails with the
holes in the rear handle, select
the preferred handle height, then
secure the handle assembly with
the bolts and locking knobs (Fig.4).
Please see section HANDLE
HEIGHT ADJUSTMENT for detailed
adjustment instructions.
2
Handle Assmbly
Locking Knob
3
Bolt
Rear Handle
Locking Knob
4
Side Rail
Rear Handle
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC16
TO INSTALL THE SNOW-
DISCHARGE CHUTE ASSEMBLY
WARNING: Never operate the
snow blower without the complete
discharge chute in place.
1. Loosen the knob on the inner
support pole and remove the bolt
(Fig.5). Save the knob and bolt for
reassembly.
2. Lift the snow-discharge chute
assembly, align the outer support
pole with the inner support pole,
and then slide the outer support
pole into place (Fig. 5). Make sure
that the snow-discharge chute is
correctly seated on the base (Fig.6).
3. Secure the snow discharge chute assembly with the reserved knob and bolt.
WARNING: Use the chute rotation handle to make sure that the chute rotates
properly and that the discharge opening never crosses the operator controls.
6
Snow-discharge
Chute
Base
5Outer Support Pole
Knob
Base
Bolt Inner Support Pole
Snow-discharge
Chute
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 17
OPERATION
WARNING: Do not allow familiarity with this product to make you careless.
Remember that a careless fraction of a second is sufcient to inict serious injury.
WARNING: Always wear eye protection with side shields marked to comply with
ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes and
other possible serious injuries.
WARNING: Do not use any attachments or accessories not recommended by the
manufacturer of this product. The use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATION
You may use this product for purpose listed below:
Removing snow from areas such as driveways and sidewalks.
HANDLE-HEIGHT ADJUSTMENT
The handle assembly can be set to three
different heights. Choose a comfortable
operating position according to your
height.
1. Loosen the two upper locking knobs
and pull out the two bolts (Fig.7).
Save them for reassembly.
2. Loosen the two lower locking knobs. It is not necessary to remove the two lower
locking knobs and bolts from the side rails during handle height adjustment.
3. Raise or lower the handle and select the appropriate height relative to the
positions of the holes in the rear handle.
4. Once arriving at the appropriate holes, tighten the handle with the reserved knobs
and bolts; then tighten the two lower locking knobs to secure the rear handle.
7
Upper
Locking Knob
Lower
Locking Knob
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC18
The illustration shows the upper operating
position (Fig.8), the middle operating
position (Fig.9) and the lower operating
position (Fig.10).
TO ATTACH/DETACH THE
BATTERY PACK
CHARGE BEFORE FIRST USE.
NOTE: For best performance, we
recommend use with two 5.0 Ah EGO 56V
Arc-Lithium batteries or with two EGO 56V
Arc-Lithium batteries of greater capacity.
When not in use, 56V battery packs
should be stored in an enclosed area
where the temperature will not drop
below -4°F (-20°C). Optimal charging
temperatures are between 41°F (5°C) and
104°F (40°C).
WARNING: If any parts are broken
or missing, do not attempt to attach the
battery packs to the snow blower or
operate the snow blower until the broken
or missing parts are replaced. Failure to
do so could result in serious injury.
1. The battery cover is hinged. Raise the battery cover by lifting the front of the
cover.
2. The snow blower is equipped with two battery compartments, which
accommodate two battery packs at the same time.
8
Upper
Operating
Position
9
Middle
Operating
Position
10
Lower
Operating
Position
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC 19
3. Align the grooves in the battery
pack with the raised ribs in one
of the battery compartments, and
then insert the battery pack into the
compartment (Fig.11).
4. Push the battery pack until you hear
a “click”. The battery-release button
will spring up when the battery pack
is securely attached.
5. Attach the other battery pack into
the other battery compartment in the
same way.
6. To detach the battery pack, depress
the battery-release button to release
the battery pack, and then lift it out of
the compartment (Fig. 12).
7. Close the battery cover.
NOTICE: Make sure that the latch on the snow blower snaps into place and that the
battery pack(s) are secured to the unit before starting operation.
STARTING/STOPPING THE SNOW BLOWER
CAUTION: Do not attempt to override the operation of the safety button. Do not
rapidly turn the snow blower off and on.
WARNING: The operation of a snow blower can result in foreign objects being
thrown into your or others’ eyes, which can damage eyes severely. Always wear safety
glasses while operating the snow blower or while performing any adjustments or repairs
on the snow blower.
WARNING: Ensure that other people and pets remain at least 100’ (30m) away from
the snow blower when it is in use.
WARNING: The auger will continue to rotate for a few seconds after the snow
blower is turned off. Allow the auger to stop rotating before starting it again.
Install
Battery
11
2
1
Remove
Battery
12
Battery-
Release
Button
56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2400/SNT2400-FC20
To Start the Snow Blower
1. Ensure that the handle assembly is securely adjusted to appropriate height, the
side-discharge chute assembly is mounted properly, and the chute and chute
deector are adjusted to an appropriate position.
2. Attach the battery pack(s) to the snow blower and close the battery cover.
NOTICE: Make sure that the latch on the snow blower snaps into place and that the
battery pack(s) are secured to the snow blower before operation.
3. Press the safety button and hold for
1 second, and the LED indicator will
blink green. Press the auger-switch
trigger to turn on the snow blower
while the LED indicator blinks
(Fig.13).
NOTICE: The snow blower can be
turned on by the auger-switch-trigger only
when the LED indicator blinks.
NOTICE: The snow blower may not properly start if its battery temperature is -4°F
(-20°C) or less. If the snow blower doesn’t start, remove the battery from the snow
blower and allow it to warm indoors for 10 minutes or longer. Reinstall the battery and
try again.
To Stop the Snow Blower
1. Fully release the auger-switch trigger.
2. The electric brake in the Automatic Braking Mechanism will stop the auger
rotation within 3 seconds of the auger-switch release.
Variable-Auger-Speed System (Fig. 13)
The speed of the auger can be adjusted to control the throwing distance.
1. To increase the speed, push the auger-speed-control lever forwards.
2. To decrease the speed, pull the auger-speed-control lever backwards.
13 Auger-Switch Trigger
Auger-Speed-Control Lever
Safety Button
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120

EGO SNT2405 Le manuel du propriétaire

Catégorie
Souffleuses à neige
Taper
Le manuel du propriétaire

dans d''autres langues