EGO SNT2114 Le manuel du propriétaire

OPERATOR'S MANUAL

56-VOLT LITHIUM-ION

CORDLESS

SNOW BLOWER

MODEL NUMBER SNT2110/SNT2110-FC

WARNING: To reduce the risk of injury, the user must read and understand the

Operator’s Manual before using this product. Save these instructions for future reference.

Español p. 73

Français p. 35

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC2

TABLE OF CONTENTS

Safety Symbols ..........................................4

Safety Instructions ......................................5-6

Safe Operation Practices for Walk-behind Snow Blower .........6-9

Introduction ............................................10

Specications ..........................................10

Description .........................................11-12

Assembly ...........................................13-16

Operation ...........................................17-25

Maintenance ........................................26-30

Troubleshooting .........................................31

Accessories ............................................32

Warranty ...........................................33-34

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 3

READ ALL INSTRUCTIONS!

READ & UNDERSTAND

OPERATOR'S MANUAL

WARNING: Some dust created by power cutting contains chemicals known to

the state of California to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

◾Lead from lead-based paints

◾Crystalline silica from bricks and cement and other masonry products, and

◾Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to lter out microscopic particles.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC4

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The

safety symbols and the explanations with them deserve your careful attention and

understanding. The symbol warnings do not, by themselves, eliminate any danger.

The instructions and warnings they give are no substitutes for proper accident

prevention measures.

WARNING: Be sure to read and understand all safety instructions in this

Operator’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,”

and “CAUTION” before using this tool. Failure to follow all instructions listed below may

result in electric shock, re, and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION.

May be used in conjunction with other symbols or pictographs.

WARNING: The operation of any power tools can result in

foreign objects being thrown into your eyes, which can result in severe

eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and a full face shield

when needed. We recommend a Wide Vision Safety Mask for use over

eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 5

SAFETY INSTRUCTIONS

This page depicts and describes safety symbols that may appear on this product.

Read, understand, and follow all instructions on the machine before attempting to

assemble and operate.

Safety Alert Indicates a potential personal injury hazard.

Eye Protection

Always wear safety goggles or safety glasses

with side shields and a full face shield when

operating this product.

Read &

understand

Operator's

Manual

To reduce the risk of injury, user must read

and understand operator’s manual before

using this product.

DANGER —

Keep Hands

Away from the

Impeller

Do not use hands to unclog the chute.

Keep Feet Out of

Impeller Keep feet away from rotating impeller

Recycle Symbols

This product uses Lithium-ion (Li-ion)

batteries. Local, state, or federal laws may

prohibit disposal of batteries in ordinary

trash. Consult your local waste authority for

information regarding available recycling and/

or disposal options.

IPX4 Ingress Protection

Degree Protection from splashing water

V Volt Voltage

Direct Current Type or a characteristic of current

cm centimeter Length or size

in. Inch Length or size

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC6

Ft. Feet Length or size

kg Kilogram Weight

lb Pound Weight

WARNING: To ensure safety and reliability, all repairs should be performed by a

qualied service technician.

SAFE OPERATION PRACTICES FOR WALK-BEHIND

SNOW BLOWER

DANGER: This snow blower is capable of amputating hands and feet and

throwing objects. Failure to observe the following safety instructions could result in

serious injury.

FOR ALL SNOW BLOWERS

◾Do not use on graveled surface.

◾Keep Children Away – All visitors should be kept a safe distance from work area.

◾Dress Properly – Do not wear loose clothing or jewelry. They can be caught in

moving parts.

◾Wear rubber boots when operating the snow blower.

◾Keep hands away from moving parts.

◾Keep guards in place and in working order.

◾Don’t Force Snow Blower – It will perform better and safer at the rate for which it

was designed.

◾Don’t Overreach – Keep proper footing and balance at all times.

◾If the snow blower strikes a foreign object follow these steps:

1) Stop snow blower. Release the switch.

2) Remove the battery pack(s).

3) Inspect for damage.

4) Repair any damage before restarting and operating the snow blower.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 7

◾Store Idle Snow Blowers Indoors-When not in use, snow blowers should be stored

indoors in dry, locked-up place – out of reach of children.

◾Maintain Snow Blowers with Care – Following instructions for lubricating and

changing accessories.

TRAINING

◾Read, understand and follow all instructions on the machine and in the

manual(s) before operating this unit. Be thoroughly familiar with the controls and

the proper use of the equipment. Know how to stop the unit and disengage the

controls quickly.

◾Never allow children to operate the equipment. Never allow adults to operate the

equipment without proper instruction.

◾Keep the area of operation clear of all persons, particularly small children.

◾Exercise caution to avoid slipping or falling, especially when operating the snow

blower in reverse.

PREPARATION

◾Thoroughly inspect the area where the equipment is to be used and remove all

doormats, sleds, boards, wires, and other foreign objects.

◾Do not operate the equipment without wearing adequate winter garments. Avoid

loose-tting clothing that can get caught in moving parts. Wear footwear that will

improve footing on slippery surfaces.

◾Never attempt to make any adjustments while the motor is running (except when

specically recommended by manufacturer).

◾Always wear safety glasses or eye shields during operation or while performing

an adjustment or repair to protect eyes from foreign objects that may be thrown

from the machine.

OPERATION

◾Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to battery pack, picking up or carrying the appliance. Carrying the

appliance with your nger on the switch or energizing appliance that have the

switch on invites accidents. Do not put hands or feet near or under rotating parts.

Keep clear of the discharger opening at all times.

◾Do not put hands or feet near or under rotating parts. Keep clear of the discharger

opening at all times.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC8

◾Exercise extreme caution when operating on or crossing gravel drives, walks, or

roads. Stay alert for hidden hazards or trafc.

◾After striking a foreign object, stop the motor, remove the battery pack(s),

thoroughly inspect the snow blower for any damage, and repair the damage

before restarting and operating the snow blower.

◾If the unit should start to vibrate abnormally, stop the motor and check

immediately for the cause. Vibration is generally a warning of trouble.

◾Stop the motor whenever you leave the operating position, before unclogging

the auger assembly housing or discharge chute, and when making any repairs,

adjustments or inspections.

◾When clearing, repairing or inspecting the snow blower, stop the motor and make

certain the auger assembly and all moving parts have stopped. Remove the

battery pack(s) to prevent someone from accidentally starting the motor.

◾Exercise extreme caution when operating on slopes.

◾Never operate the snow blower without proper guards and other safety protective

devices in place and working.

◾Never direct the discharge toward people or areas where property damage can

occur. Keep children and others away.

◾Do not overload the machine capacity by attempting to clear snow at too fast a

rate.

◾Disengage power to the auger assembly when snow blower is transported or not

in use.

◾Use only attachments and accessories approved by the manufacturer of the snow

blower (such as rubber paddles, scraper bar and drive belt).

◾Never operate the snow blower without good visibility or light. Always be sure of

your footing, and keep a rm hold on the handles. Walk; never run.

◾Do not expose a battery pack or tool to re or excessive temperature. Exposure to

re or temperature above 212 °F (100°C) may cause explosion.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 9

◾Use only with the battery packs and chargers listed below:

BATTERY PACK CHARGER

BA1400, BA1400-FC, BA2800, BA2800-FC,

BA4200, BA4200-FC, BA1400T, BA1400T-FC,

BA2800T, BA2800T-FC, BA4200T, BA4200T-FC,

BA5600T, BA5600T-FC

CH2100, CH2100-FC,

CH5500, CH5500-FC,

CH7000,CH7000-FC,

CH2800D,CH2800D-FC

NOTICE: For best performance, recommend for use with 2pcs 5.0Ah or higher Ah batteries.

CLEARING A CLOGGING DISCHARGE CHUTE

Hand contact with the rotating auger assembly inside the discharge chute is the most

common cause of injury associated with snow blowers. Never use your hand to clean

out the discharge chute.

To clear the chute:

◾SHUT THE MOTOR OFF!

◾Wait 10 seconds to be sure the auger assembly blades have stopping rotating.

◾Always use a clean-out tool, not your hands.

MAINTENANCE AND STORAGE

◾Check all bolts or fasteners at frequent intervals for proper tightness to be sure

the equipment is in safe working condition.

◾Always refer to operator’s manual for important details if the snow blower is to be

stored for an extended period.

◾Maintain or replace safety and instruction labels, as necessary.

◾Run the machine a few minutes after blowing snow to prevent freeze-up of the

auger assembly.

SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others

who may use this tool. If you lend this tool to someone else, also lend these instructions

to them to prevent misuse of the product and possibly injury.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC10

INTRODUCTION

Congratulations on your selection of a new generation of 56V Lithium-Ion powered

snow blower. It has been designed, engineered and manufactured to give you the best

possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact EGO

customer service center 1-855-EGO-5656.

This manual contains important information on to the safe assembly, operation and

maintenance of your snow blower. Read it carefully before using the tool. Keep this

manual handy so you can refer to it at any time.

SERIAL NUMBER _____________________ DATE OF PURCHASE _________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A LABEL ATTACHED ON AUGER

ASSEMBLY HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE

PLACE FOR FUTURE REFERENCE. SAVE YOUR SALES RECEIPT.

SPECIFICATIONS

Voltage 56V

Clearing Width 21 in

Intake Height 13 in

Throwing Distance Up to 40 ft.

Wheel Size 7 in

Operating Temperature -4°F-50°F(-20°C-10°C)

Storage Temperature -4°F-158°F(-20°C-70°C)

Snow Blower Weight (Without battery pack) 53 lbs(24.05 kg)

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 11

DESCRIPTION

1Handle

Safety Button

Variable-Auger-

Speed Adjustment

Rear Handle

Quick-Release

Lever

Wheels

Drive-Belt Cover

Bail Switch

(Switch Lever)

LED Headlights

Battery-Release Button

Switch Button for

LED Headlights

Knob

Power Indicator

Electric Contact

Steel Auger

Chute Deector

Chute-Deector Handle

Battery Cover

Chute-Rotation Handle

WARNING: The safe use of this product requires an understanding of the

information on the tool and in this operator’s manual, as well as knowledge of the project

you are attempting. Before use of this product, familiarize yourself with all operating

features and safety rules.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC12

Safety Button

The safety button must be pressed down before the motor can be started.

Bail Switch

The bail switch is located on the upper handle of the snow blower. The switch

engages and disengages the motor and auger.

WARNING: The bail switch and the safety button are safety devices. Never

attempt to bypass their operations.

Electric Brake

Quickly stops auger rotation when the bail switch is released.

Quick-Release Lever

Locks/unlocks the side rails for working or storage positions.

Variable-Auger-Speed Adjustment

Adjusts the auger speed in order to adjust the throwing distance.

Chute-Rotation Handle

Rotates the chute so that the user may direct the discharged snow as desired. The

handle allows the chute to rotate left 90° to right 90°.

Chute-Deector Handle

Adjusts the angle of the chute and the height of the discharge stream.

LED Headlights

The LED headlights are located on the front of the unit. This feature provides extra light

for increased visibility.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 13

ASSEMBLY

WARNING: To prevent accidental starting that could cause serious personal

injury, always remove the battery pack(s) from the tool when assembling parts.

WARNING: If any parts are damaged or missing, do not operate this product

until the parts are replaced. Use of this product with damaged or missing parts could

result in serious personal injury.

WARNING: Do not attempt to modify this tool or create accessories not

recommended for use with this product. Any such alteration or modication is misuse

and could result in a hazardous condition leading to serious injury.

UNPACKING

◾Grasp the rear handle and the front part of the product at the same time to

carefully lift the tool up and out of the carton. Remove any other accessories from

the carton. Make sure that all items listed in the packing list are included.

WARNING: Do not use this product if any parts on the packing list are already

assembled to your product when you unpack it. Parts on this list are not assembled to

the product by the manufacturer and require customer installation. Use of a product

that may have been improperly assembled could result in serious personal injury.

◾Inspect the product carefully to make sure that no breakage or damage occurred

during shipping.

◾Do not discard the packing material until you have carefully inspected and

satisfactorily operated the tool.

◾If any parts are damaged or missing, please return the product to the place of

purchase.

LIST OF CONTENTS

PART NAME QUANTITY

Snow Blower 1

Discharge Chute 1

Operator’s Manual 1

Hex Wrench 1

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC14

UNFOLDING/FOLDING THE

SIDE RAILS

WARNING: Do not attempt to start

the snow blower when the side rails are

folded down.

To unfold the side rails

1. Your snow blower is shipped with

the side rails in the compact, locked

position (Fig. 2).

2. Open the quick-release levers on

both sides and gently pivot the side

rails upwards until they come to a

stop (Fig. 3 & 4).

3. Close the quick-release levers and

then tighten the knobs to secure the

side rails in place (Fig. 5).

2

4

3

5

12

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 15

To fold the side rails

1. Push the chute-rotation handle all

the way forward so that the chute is

facing left as you stand behind the

snow blower. Squeeze the trigger on

the chute deector handle to tilt it all

the way down (Fig. 6).

2. Open the quick-release levers on

both sides to fold the side rails into

the storage position (Fig. 7). 7

1

2

61

2

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC16

INSTALLING THE CHUTE

1. Use the supplied hex wrench to

loosen the two bolts in the chute

housing and remove them (Fig. 8).

2. Align the grooves of the chute with the

slot on the chute housing, and then

push the chute into place (Fig. 9).

3. Use the hex wrench to lock the chute

in place with the two bolts (Fig. 10).

WARNING: Using the chute-

rotation handle located at the operator’s

position, make sure that the chute rotates

properly with the discharge opening never

crossing operator controls.

WARNING: Never operate the

snow blower without the complete

discharge chute in place.

8Chute

Housing

9

Slot on

the Chute

Housing

Groove of the Chute

10

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 17

OPERATION

WARNING: Do not allow familiarity with this product to make you careless.

Remember that a careless fraction of a second is sufcient to inict serious injury.

WARNING: Always wear eye protection with side shields marked to comply with

ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes and

other possible serious injuries.

WARNING: Do not use any attachments or accessories not recommended by the

manufacturer of this product. The use of attachments or accessories not recommended

can result in serious personal injury.

APPLICATION

You may use this product for purpose listed below:

Removing snow from areas such as driveways and sidewalks.

TO ATTACH/DETACH THE BATTERY PACK

CHARGE BEFORE FIRST USE.

NOTE: For best performance, we recommend use with two 5.0Ah EGO 56V Arc-

Lithium batteries or with two EGO 56V Arc-Lithium batteries of greater capacity.

When not in use, 56V battery packs should be stored in an enclosed area where the

temperature will not drop below -4°F (-20°C). Optimal charging temperatures are

between 41°F (5°C) and 104°F (40°C).

WARNING: If any parts are broken or missing, do not attempt to attach the

battery packs to the snow blower or operate the snow blower until the broken or

missing parts are replaced. Failure to do so could result in serious injury.

1. The battery cover is hinged. Raise the battery cover by lifting the front of the

cover.

2. The snow blower is equipped with two battery compartments, which

accommodate two battery packs at the same time.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC18

3. Align the grooves in the battery

pack with the raised ribs in one

of the battery compartments, and

then insert the battery pack into the

compartment (Fig. 11).

4. Push the battery pack until you hear

a “click”. The battery-release button

will spring up when the battery pack

is securely attached.

5. Attach the other battery pack into

the other battery compartment in

the same way.

6. To detach the battery pack, depress

the battery-release button to release

the battery pack, and then lift it out

of the compartment (Fig. 12).

7. Close the battery cover.

NOTICE: Make sure that the latch on

the snow blower snaps into place and that the battery pack(s) are secured to the unit

before starting operation.

STARTING/STOPPING THE SNOW BLOWER

CAUTION: Do not attempt to override the operation of the safety button and bail

switch.

WARNING: The operation of a snow blower can result in foreign objects being

thrown into your or others’ eyes, which can damage eyes severely. Always wear safety

glasses while operating the snow blower or while performing any adjustments or repairs

on the snow blower.

WARNING: Ensure that other people and pets remain at least 100’ (30m) away from

the snow blower when it is in use.

11 Install Battery

Battery-

Release

Button

Battery

Compartment

Battery Cover

12 Remove Battery

2

1

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC 19

WARNING: The auger will continue to rotate for a few seconds after the snow

blower is turned off. Allow the auger to stop rotating before starting it again.

NOTICE: Do not rapidly turn the snow blower off and on.

To Start the Snow Blower

1. Ensure that the side rails are

securely locked in the unfolded,

open position.

2. Attach the battery pack(s) to the

snow blower and close the battery

cover.

NOTICE: Make sure that the latch on the

snow blower snaps into place and that the

battery pack(s) are secured to the snow

blower before operation.

3. Depress the safety button and, with

the button depressed, pull the bail

switch upward to meet the handle

(Fig. 13 &14).

4. Once the tool powers on, release the

safety button and begin operation

(Fig. 15).

NOTICE: The tool is started by

depressing the safety button rst,

followed by squeezing the bail switch; the

reverse operation will not start the tool.

NOTICE: The snow blower may not

properly start if its battery temperature

is -4°F (-20°C) or less. If unit doesn’t

start, remove the battery from the snow

blower and allow it to warm indoors for

10 minutes or longer. Reinstall the battery and try again.

21

13

15

14

1

2

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2110/SNT2110-FC20

To Stop the Snow Blower

1. Fully release the bail switch (Fig. 16).

2. The electric brake in the Automatic

Braking Mechanism will stop the

auger rotation within 3 seconds of

the bail-switch release.

Variable-Auger-Speed System

(Fig. 17)

The speed of the auger can be adjusted to

control the throwing distance.

1. To increase the speed, move the

variable-auger-speed adjustment

forwards.

2. To decrease the speed, move the

variable-auger-speed adjustment

backwards.

ADJUSTING THE CHUTE

The chute can be adjusted to change

both the direction and the distance of the

discharged snow to assist you in moving

snow away from one area and placing it

in another.

The direction of snow removal can be

adjusted up to 180° (Fig. 18).

1. Push the chute-rotation handle forward to rotate the chute to the left.

2. Pull the chute-rotation handle backward to rotate the chute to the right.

16 Bail Switch (Fully released)

Safety Button

(Fully released)

17

Variable-Auger-

Speed Adjustment

18

Chute-Rotation

Handle

Chute

La page charge ...

EGO SNT2114 Le manuel du propriétaire

Ce manuel convient également à

EGO SNT2114 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents