EarthWise SN74018 Manuel utilisateur

Model SN74018

OPERATOR’S MANUAL

18-IN Lithium Snow Thrower

This product is covered by U. S. patents and other international patents

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PARTS, SERVICE QUESTIONS?

CALL 1-800-313-5111 BETWEEN 8:00AM-5:00PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’ manual

before using this product.

CA Compliant Charger

Included (Model No.

CHL80040)

Precautions that involve your safety.

CAUTION! Read the instruction manual and follow the warning and safety instructions!

CAUTION! Remove plug from outlet immediately if the cable is damaged or cut.

SWITCH OFF! the machine, wait until it comes to a complete standstill and remove battery prior to

maintenance, cleaning or repair work!

CAUTION! Always wear eye and ear protection.

Wear safe, sturdy, nonskid footwear!

DANGER! objects may be thrown out at high speed when motor is running. Do not walk in front of running

machine.

Keep bystanders at a safe distance.

Keep the electrical cord free of the auger. The auger may damage the cord and cause contact with live

parts.

DANGER! Rotating auger. Keep hands and feet at a safe distance.

Do not place hand under auger.

Do not place hand in front of chute deflector.

Do not expose to rain or use in damp locations.

DANGER! Risk of electric shock.

Do not use in rain or electrical storms.

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or retailer for recycling advice.

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

2

TO REDUCE RISK OF INJURY: Before any use

be sure everyone using this product reads and

understands all safety instructions and other

information contained in this manual.

CAUTION: Wear appropriate personal hearing

protection during use. Under some conditions and

duration of use, noise from this product may

contribute to hearing loss.

Save these instructions and review frequently prior

to use and in instructing others.

WARNING: When using electric appliances, basic

safety precautions should always be followed to

reduce risk of fire, electric shock, and personal

injury, including the following:

READ ALL INSTRUCTIONS

CHECK FOR DAMAGED PARTS - Before further

use of the product, any part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check

for alignment of moving parts, binding of moving

parts, breakage of parts, mounting and any other

condition that may affect its operation. Any part that

is damaged should be properly repaired or replaced.

For assistance call our customer service help line at

1-800-313-5111.

AVOID DANGEROUS ENVIRONMENTS - Do

not operate in gaseous or explosive atmospheres.

Motors in these products normally spark, and the

sparks might ignite fumes.

KEEP CHILDREN AWAY - All visitors, children and

pets should stay at a safe distance from the work

area.

DRESS PROPERLY- Don’t wear loose clothing or

jewelry and wear protective hair covering to contain

long hair. They can be caught in moving parts.

Wear safe, sturdy, nonskid footwear. Maintain good

footing at all times, especially on slopes.

USE SAFETY GLASSES - Wear safety glasses

with side shields or goggles that are marked to

comply with ANSI Z87.1 standard when operating

this product.

WARNING: Keep hands away from moving parts.

Never put your hands near the auger to remove

snow, sticks or other debris. Blocked auger can

―spring back‖ when cleared and may cause

personal injury even when the snow thrower is

stopped. Always use a wooden stick such as a

broom handle to clear blockages.

REMOVE THE BATTERY from the snow thrower

when not in use or when servicing or cleaning. Do

not leave unattended.

USE RIGHT APPLIANCE - Do not use this product

for any job except that for which it is intended.

AVOID ACCIDENTAL STARTING—Don’t carry

snow thrower with finger on switch when the battery

is installed. Be sure switch is off when installing

battery.

DO NOT OVERLOAD the snow thrower by using at

too fast a rate to clear the snow. The snow thrower

will perform better and safer at the rate for which it

was designed.

DON’T OVERREACH - Guide the snow thrower at

a walking pace only. Keep proper footing and

balance at all times.

LIGHTING - Only operate your snow thrower in

daylight or good artificial light.

STORE IDLE UNIT INDOORS-When not in use,

the snow thrower should be stored indoors in a dry

area out of reach of children.

MAINTAIN UNIT WITH CARE-Keep clean for best

performance and to reduce the risk of injury.

Keep handles dry, clean and free from oil.

Do not operate the snow thrower on a slope that is

too steep for safe operation. When on slopes, slow

down and make sure you have good footing.

Before starting the snow thrower make sure the

auger is not touching any object and is free to

move.

Do not attempt to clear snow from a gravel or

crushed rock surface. This product is only intended

for use on hard, flat surfaces free of sand, stone

and debris, wires or any other objects.

Operation of the snow thrower in the hand-held

position is unsafe except in accordance with the

special instructions for such use provided in the

operator’s manual.

CAUTION: Never throw snow towards people, pets

or cars and never allow anyone in front of the snow

thrower while in operation.

Objects that might clog the snow thrower or cause

other damage can be hidden in the snow. Clear the

area of doormats, sleds, boards, wires and other

debris prior to use.

If the auger strikes a foreign object, stop the snow

thrower and examine it for signs of damage. Make

any necessary repairs before restarting and

continuing to work.

STAY ALERT - Watch what you are doing. Use

common sense. Do not operate the snow thrower

when you are tired or under the influence of drugs,

alcohol or medications.

IMPORTANT SAFETY WARNINGS

GENERAL SAFETY

3

If the snow thrower starts to vibrate abnormally, turn it off

immediately and check for the cause. Vibration is

generally a warning of trouble.

Always turn off the snow thrower, wait until the auger

comes to a complete stop and remove the battery before

carrying out maintenance or repairs.

Never operate the snow thrower without proper guards

and other safety protective devices in place and

working.

GENERAL SAFETY

4

SAFETY RULES FOR CHARGER

FCC WARNING:

Please note that changes or modifications to this

product not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and

receiver.

-- Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV

technician for help.

Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away from

heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

Use of an attachment not recommended or sold by the

battery charger manufacturer may result in a risk of fire,

electric shock, or injury to persons. Following this rule will

reduce the risk of electric shock, fire, or serious personal

injury.

Do not service snow thrower with battery, switch key, or

charger installed.

Do not use the charger when the ambient temperature is

above 100°F (37.8°C) or below 32°F (0°C)

Do not operate charger with a damaged cord or plug

which could cause shorting and electric shock. If

damaged, replace the charger with an identical charger.

Do not operate charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it

to a qualified individual for electrical check to determine if

the charger is in good working order.

Unplug charger from outlet before attempting any

maintenance or cleaning to reduce the risk of electric

shock.

Disconnect charger from the power supply when not in

use to prevent damage to the charger during a power

surge.

Risk of electric shock, Do not touch uninsulated portion of

output connector or uninsulated battery terminal.

Do not expose charger to wet or damp conditions, Water

entering charger will increase the risk of electric shock.

Make sure cord is located so that it will not be stepped on,

tripped over, come in contact with sharp edges or moving

parts or otherwise subjected to damage or stress. This will

reduce the risk of accidental falls, which could cause

injury and damage to the cord, which could result in

electric shock.

Keep cord and charger away from heat to prevent

damage to housing or internal parts.

Do not let gasoline, oils, petroleum-based products, etc.

come in contact with plastic parts. They contain chemicals

that can damage, weaken or destroy plastic.

An extension cord should not be used unless

absolutely necessary. Use of improper extension cord

could result in a risk of fire and electric shock. If

extension cord must be used, make sure:

a. That pins on plug of extension cord are the same

number, size and shape as those of plug on

charger

b. That extension cord is properly wired and in good

condition; and

c. That wire size is large enough for AC ampere

rating of charger as specified below:

Cord length (Feet) - 25’ 50’ 100’

Cord Size (AWG) - 16 16 16

NOTE: AWG= American Wire Gauge

Save these instructions. Refer to them frequently and

use them to instruct others who may use this product.

If you loan someone this snow thrower, loan them

these instructions also.

WARNING: Keep all connections dry and off the

ground. Do not touch plug with wet hands.

CAUTION: Auger does not stop immediately after the

snow thrower is turned off.

CAUTION: Risk of injury. This snow thrower is capable

of causing serious injury. Do not put hands, feet or any

body part or clothing near the rotating auger.

WARNING: California Proposition 65:

This product contains chemicals known to the State of

California to cause cancer, birth defects or other

reproductive harm.

PRODUCT SPECIFICATIONS

Model: SN74018

Power supply voltage: 40V, DC only Clearing width: 18 inches (460 mm)

Speed: 2000 RPM Max clearing depth: 12 inches (305 mm)

Battery: 40V, 4.0 Ah Lithium-ion Max clearing capacity: 500 pounds/minute

Charging time: 2.5 hours Max throwing distance: Up to 30 feet

Battery run time: 20-50 minutes Weight: 31.6 pounds

5

PARTS LIST

No. Description

1 Upper handle

2 Bail wire

3 Switch button

4 Cable clip

5 Crank handle

5A Upper crank

5B Lower crank

6 J bolt

7 Knob

8 Center handle

9 Cotter pin

No. Description

10 Auxiliary handle

11

Battery

compartment

12 Lower handle

13 Wheel assy.

14 Scraper blade

15 Auger

16 Side cover

17 Discharge chute

18 Chute deflector

19 Battery pack

20 Charger

5A

5B

1

2

3

4

5

6

7

8 9

10

11

12

13

14

15

16

17

18

19

20

ASSEMBLY

6

UNPACKING

This product requires assembly.

Carefully remove everything from the box. Make sure that

all items listed in the packing list are included.

Inspect all items carefully to make sure no breakage or

damage occurred during shipping.

Do not discard the packing material until you have

carefully inspected and satisfactorily operated the snow

thrower.

If any parts are damaged or missing, please call our

customer service help line at 1-800-313-5111 for

assistance.

PACKING LIST

- Snow Thrower

- Handle Assembly

- Chute Crank

- Chute Deflector

- Battery & Charger

- Hardware Bag

- Operator’s Manual

INSTALLING CENTER HANDLE

 Position the center handle onto the lower handles and

make sure the bracket is pointed downward. (See Fig

1)

 Align the holes on the center handle with the holes in

the lower handle as shown. (See Fig 2)

 Insert J-bolt through both handles with the threaded

end at the bottom and facing inside. (See Fig 3)

 Install the handle knob and tighten securely to secure

the bolt in place. (See Fig 4)

 Repeat on the opposite side to secure the center

handle in place. (See Fig 5)

Fig. 5

Fig. 4

Fig. 3

Fig. 2

Fig. 1

INSTALLING CHUTE CRANK

 Install the upper chute crank through the bracket

located on the center handle. (See Fig 8)

 Align the holes in the upper and lower cranks and

insert the cotter pin through the holes as shown to

secure. (See Fig 9 and Fig 10)

 Turn the lever left and right to verify the proper

functioning of the crank and the chute.

ASSEMBLY

7

INSTALLING UPPER HANDLE

 Align the holes on the upper handle with the holes in

the center handle as shown. (See Fig 6)

 Insert threaded end of J bolt through both handles with

the threaded end facing inside.

 Install the handle knob and tighten secure.

 Repeat on the opposite side.

 Secure the cable clip to handles. (See Fig 7).

Fig. 8

Fig. 9

Fig. 10

Fig. 6

Fig. 7

ASSEMBLY

8

INSTALLING CHUTE DEFLECTOR

 Position the chute deflector over the discharge chute.

(See Fig 11)

 Align the holes and place the washer between the

deflector and chute. (See Fig 12)

 Securely tighten the knobs. (See Fig 13 - 14)

Fig. 11

Fig. 12

Fig. 13

Fig. 14

Check the condition of the snow thrower before operating

it to ensure that the auger turns freely.

Check the auger for wear and tear at regular intervals.

Make sure all fasteners on the snow thrower (screws,

nuts, etc.) are fully tightened.

Position the discharge chute so that snow will discharge

in a safe direction. Do not direct the discharge towards

people or areas where property can be damaged. Keep

children, pets and others away for the work area. Do not

walk in front of the snow thrower when it is running.

Direct the discharge to the right or left by turning the

discharge chute with the chute crank. The chute can be

adjusted up to 180 degrees.

The chute deflector on the top of the discharge chute

controls the height of the discharge. Loosen both of the

knobs to raise or lower the deflector to the desired height

and tighten the knobs to secure the deflector.

NOTE: Do not over-tighten the knobs.

For the most efficient snow removal throw the snow

downwind and slightly overlap each swath.

Push the snow thrower forward at a comfortable rate of

speed, yet slow enough to clear the path completely. The

width and depth of the snow determines your forward

speed.

When turning at the end of a swath, use the wheel on

one side as the pivot point. Slightly tilt the snow thrower

on this pivot point while turning.

The snow thrower can remove up to 12 inches deep in

one pass. To shave down larger banks of snow, lift the

snow thrower by the primary and auxiliary handles and

place the snow thrower on the bank. Let the weight of

the snow thrower shave down the bank by rocking it in a

back-and-forth motion.

When clearing steps, hold the snow thrower by the

primary and auxiliary handles and use a swinging or

sweeping motion.

Clear snow often, before it gets too deep. It is best to

remove the snow as soon as possible after it falls.

Some parts of the snow thrower may freeze under

extreme temperature conditions. If parts freeze while the

snow thrower is in use, stop the snow thrower, remove

the battery and inspect for frozen parts. Free all parts of

ice before restarting or operating the snow thrower. Do

not attempt to operate the snow thrower with frozen parts

or try to force controls that are frozen.

OPERATING

9

If working on pebbles, gravel or unpaved surfaces - To

avoid throwing loose surface material along with the

snow, push down on the handle to raise the scraper at

the base of the unit above the pebbles or gravel. The

manufacturer is not liable for any damage or injury

resulting from misuse.

Install battery

BATTERY MUST BE CHARGED BEFORE FIRST USE.

Open the battery compartment cover and slide the

battery down until it clicks to lock it into position, then

close the battery department cover.

Turning On and Off

WARNING: The auger starts rotating immediately after

the snow thrower is switched on. Keep hands and feet

away from the auger.

To switch ON, make sure the auger is not touching any

surface. Press the safety lock off button while squeezing

the bail wire toward the handle.

Once the snow thrower is started you can release the

safety lock off button.

To switch off simply release the bail wire.

LED HEADLIGHTS

LED headlights are located on the upper handle to

illuminate your path when using the snow blower in low

light conditions.

The lights may be turned on when the snow thrower is

operating. After the snow thrower is engaged by pressing

the safety lock button and pulling the bail wire toward the

handle, the lights may be turned on by pressing the on-off

switch to the on position. Lights will go out when the bail

wire is released. (See Fig 15)

The lights will illuminate when the bail wire is pulled as

long as the on-off switch remains in the on position.

When job is completed, press switch to the off position.

Removing snow

Before starting work, thoroughly inspect the area where

the equipment is to be used and remove all doormats

sleds, boards, wires and any other foreign objects.

Fig 15

ON/ OFF BUTTON

OPERATING

After clearing the snow, continue to run the snow thrower

for a few minutes to prevent ice from freezing on moving

parts. Then switch off the motor, wait for all moving parts

to stop, and wipe the ice and snow from the snow

thrower with a clean rag.

WARNING: To avoid serious personal injury, do not use

hands or feet to unclog the chute.

Before unclogging the chute, shut off the snow thrower

and remove the battery pack. Wait for the auger to stop

turning. Clean out the chute with a wooden stick such as

a broom handle.

If the snow thrower should start to vibrate abnormally,

immediately stop the motor and check for the cause.

Vibration is generally a warning of trouble.

Look behind and use care when backing up with the

snow thrower.

For large areas a definite pattern of operation is required

to thoroughly clean an area of snow. These patterns

will avoid throwing snow in unwanted places as well as

eliminating a second removal of snow.

Pattern A: Throw the snow to the right or left side where

it is possible. For areas such as a long driveway it is

advantageous to start in the middle. Plow from one end

to the other, throwing snow to both sides.

Pattern B: If the snow can only be thrown to one side of

the area to be cleared, start on the opposite side.

Overload Protection

The over current controller will automatically turn off the

snow thrower within 2 seconds when the current is over

25A. If the motor stops, you can restart the snow thrower

immediately if needed.

10

MAINTENANCE

Replacing the scraper

The scraper is located at the base of the snow thrower

beneath the auger housing.

Remove the screws that secure the scraper to the snow

thrower.

Install the new scraper and fasten it securely with the

screws. (See Fig 16)

Replacing the auger belt

Under normal operating conditions it should not be

necessary to replace the auger belt. However, should

the auger jam or malfunction the belt could be damaged.

To replace the belt follow these instructions.

Belt drive system structure (See Fig 17)

11

Regular cleaning and maintenance of your snow thrower

will ensure efficiency and prolong the life of the product.

Check all fasteners at frequent intervals for proper

tightness to be sure the snow thrower is in safe working

condition.

After each use, let the motor run for a few minutes so that

moving parts do not freeze. Then shut off the motor, wait

for all moving parts to stop, and wipe the ice and snow

from the snow thrower. Rotate the chute crank several

times to remove snow.

Only use a cloth soaked with hot water and a soft brush

to clean the snow thrower. Never wet or spray water on

the machine!

Do not use detergents or solvents as these could cause

irreparable damage to the snow thrower. Chemicals can

destroy the plastic parts.

To protect the snow thrower from corrosion when storing

for long periods, lightly oil the metal parts.

Store the snow thrower in a dry area out of reach of

children.

For the user’s safety, worn or damaged parts must be

replaced. Replace with original replacement parts only.

Parts from another snow thrower may not fit properly

causing an unsafe situation.

Lubricating the snow thrower

You do not need to lubricate the snow thrower. All of the

bearings are sealed and were lubricated at the factory for

the life of the snow thrower.

Replacing the rubber plates on auger

Detach the worn rubber plate by removing the two sets of

nuts, bolts, and washers used to secure it.

Install the new rubber plate.

Insert the bolt with the small flat washer into the

corresponding holes on each end of the rubber plate.

Use a large flat washer and locknut to secure the bolt

on each end.

Install the other rubber plate in the same manner.

Main Drive Belt

Auger Pulley

Auger Belt

Drive Pulley

Fig. 17

Fig 16

Before carrying out maintenance operations, remove the battery pack.

MAINTENANCE

1. Open the left side plate by removing three screws.

(Fig. 18)

2. Use your right hand to turn the rib side of the belt

up and pull upwards while turning the auger pulley

counterclockwise with your left hand. The belt can be

easily removed from the pulley. (Fig. 19 - 20)

12

3. Put the belt on the drive pulley first and then place

the belt at the lower end of the auger pulley. (Fig. 21)

4. Use right hand to press the belt with ribbed side

down. (Fig. 22)

5. While holding the belt down with your right hand use

your left hand to turn the auger forward so that the

auger pulley rotates in a clockwise direction. (Fig. 23)

Fig. 20

Fig. 19

Fig. 21

Fig. 22

Fig. 23

Screw

Fig. 18

MAINTENANCE

6. Keep pressure on the belt with your right hand (rib

side down and flat side up) while rotating the auger.

The belt will be gradually pushed down onto the

pulley. When the belt is seated on the pulley, adjust

it so that the ribs of the belt match the grooves on

the pulley. (Fig. 24 - 27)

Fig. 24

13

7. After belt is installed, replace the side plate and

secure it with the three screws. (Fig. 28)

Fig. 26

Fig. 25

Fig. 28

Fig. 27

Screws

14

CHARGING THE BATTERY PACK

BATTERY METER

Since the snow thrower battery is shipped in a low

charge condition, the battery must be charged before

use. The battery has 3 LED lights to indicate battery

capacity. These lights will only illuminate when the light

indicator button is pushed.

If three GREEN lights illuminate, the battery is charged

and ready for use. Two green lights are equal to 25%-

80% charge, while one green light is equal to 5%-25%

charge.

It is recommended to charge battery pack when one light

is illuminated.

CHARGING THE BATTERY PACK

The snow thrower comes with maintenance free, sealed,

40 volt storage batteries.

 Charge the battery pack only with the charger

provided.

 Allow at least two hours of charge time before initial

use of the snow thrower.

 Make sure the power supply is normal household

voltage, 120 volts, 60Hz, AC only.

 The battery should be charged in a cool, dry place.

 To improve battery life, store battery indoors in a

controlled climate. Fully charge battery pack every

3 months.

 Since the battery will not develop a memory, it does

not have to be fully discharged before recharging.

 2 to 3 initial charging/discharging cycles may be

required to achieve maximum run time/capacity.

 When fully charged, the battery can be safely stored

in temperatures down to –4˚F(-20˚C) for a period of

up to one month before requiring charging. Fully

charge battery pack every 3 months.

 The battery charger should be operated in

temperatures between 32˚F and 100˚F(0˚C and

37.8˚C).

TO CHARGE

Insert the 120 volt plug of the charger into the wall

receptacle. Light A will illuminate and stay green.

(Fig. 12)

Fig. 12

 Place the battery pack into the charger by sliding

the pack as shown in Fig. 13 to lock it into position.

Light B will illuminate red to indicate that the battery

is charging and the three lights on the battery pack

will cycle in green.

 When the battery pack is fully charged, light B will

turn green and the lights on the battery pack will shut

off. (Fig 13)

NOTE: Typical time required to reach a full charge is

2 1/2 hours.

NOTE: If light A remains green while light B alternately

flashes red and green, this indicates a temperature

abnormality (i.e. that the battery pack is either too hot or

too cold). If there is only a red blinking light, this indicates

that something is wrong with the battery. Contact

Earthwise customer service center at 1-800-313-5111 for

assistance.

If the charging light indicator Light B alternately blinks red

and green or it does not come on at all, check that the

battery pack is fully seated into the bay. Remove the pack

and reinsert. If the problem persists, contact the

Earthwise customer service center at 1-800-313-5111 for

assistance.

Fig. 13

Run the snow thrower for a few minutes to melt away any

snow on the snow thrower.

Remove the battery pack from the snow thrower.

Examine the snow thrower thoroughly for worn, loose, or

damaged parts. Check connections and screws and

tighten if necessary. To repair or replace parts, contact

our customer service help line at 1-800-313-5111.

Store the snow thrower, along with the removed battery

pack, in a clean, dry place out of reach of children. Cover

loosely with a tarp for added protection.

15

STORAGE

BATTERY DISPOSAL

Remove the battery pack from the snow thrower. Cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery

pack or remove any components. This product contains lithium-ion batteries which must be recycled or disposed of properly. Local, state or federal

laws may prohibit disposal of these batteries in ordinary trash.

The RBRC seal on the li-ion battery pack indicates that the costs to recycle the battery pack at the end of its useful life has already been

paid by The Great States Corporation American Lawn Mower Company. It is illegal to place spent li-ion batteries in the local municipal

solid waste or in the trash. RBRC in cooperation with The Great States Corporation American Lawn Mower Company has provided an

environmentally friendly and easy way to recycle spent li-ion batteries. Just contact your local recycling center or call 1-800-8BATTERY

for information on where to drop off the spent battery.

CHARGING THE BATTERY PACK

SLEEP MODE:

If the light indicator button is continuously pressed for

more than 30 seconds, the lights will go into sleep mode.

When light indicator button is pushed, no lights illuminate

(This can occasionally occur during transportation).

To re-activate battery LED lights, place the battery on the

charger and charge for one to two minutes. Battery

indicator will function normally.

16

TROUBLESHOOTING

Problem Possible causes Remedy

Motor does not start Battery not making contact.

Lock off not fully operated.

Battery not installed properly.

Battery not charged.

Check battery is fully inserted.

Check that lock off is fully forward prior to moving

trigger.

Check battery installation.

Check battery charging requirements.

Poor results Drive belt worn or damaged.

Auger worn or damaged.

Discharge blocked.

Replace the drive belt.

Replace the auger. Ensure the screws and nuts are

properly tightened.

Switch off the snow thrower, remove the battery

pack, and clean the discharge.

Abnormal vibrations Drive belt worn or damaged.

Auger worn or damaged.

Scraper blade worn or damaged.

Replace the drive belt.

Replace the auger. Ensure the screws and nuts are

properly tightened.

Replace the scraper blade. Ensure the screws are

properly tightened.

SERVICE

Should you need repair parts or service, simply contact us at 1-800-313-5111.

Be sure to provide all pertinent facts when you call.

REPAIR PARTS

Please record your serial number in the space provided below.

• NAME OF ITEM Snow Thrower

• MODEL NUMBER SN74018

• SERIAL NUMBER

CALL US FIRST !!

Call us first with questions about operating or maintaining this product at 1.800.313.5111

between 8:00 a.m. – 5:00 p.m. Eastern Standard Time, or send emails to [email protected].

The Great States Corporation

American Lawn Mower Company

830 Webster Street

Shelbyville, IN 46176

www.earthwisetools.com

Battery LED lights will

not illuminate

Battery in sleep mode Place battery on charger for one to two minutes.

NOTES

17

__________________________________________________________________

WARRANTY

This product is manufactured for The Great States Corporation/American Lawn Mower Company. The

Great States Corporation/American Lawn Mower Company, Shelbyville, Indiana, has been making

lawn mowers for over 100 years and it warrants to the original owner that each new product and

service part is free from defects in material and workmanship and agrees to repair or replace under

this warranty any defective product or part from the original date of purchase for two (2) years except

for the conditions and circumstances listed below. Proof of purchase (original dated sales receipt)

must accompany all warranty claims.

THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER:

Products sold damaged or incomplete, sold

―as is‖, sold reconditioned, or used as rental

equipment.

Delivery, installation, or normal adjustments

explained in the operator’s manual.

Damage or liability caused by shipping,

improper handling, improper installation,

incorrect voltage or improper wiring,

improper maintenance, improper

modification, or the use of accessories and/

or attachments not specifically

recommended.

Repairs necessary because of operator

abuse or negligence, or the failure to install,

operate, maintain, or store the product

according to the instructions in the

operator’s manual.

Damage caused by cold, heat, rain,

excessive humidity, corrosive environments

and materials, or other contaminants.

Expendable items that become worn

during normal use, including but not limited

to, auger and scraper blade.

Cosmetic defects that do not interfere with

product functionality.

Freight costs from customer to vendor.

Repair and transportation costs of products

or parts determined not to be defective.

ANY INCIDENTAL, INDIRECT, OR

CONSEQUENTIAL LOSS, DAMAGE, OR

EXPENSE THAT MAY RESULT FROM

ANY DEFECT, FAILURE, OR

MALFUNCTION OF THE PRODUCT.

Some states do not allow the exclusion or

limitation on how long an implied warranty

lasts, so the above limitations may not

apply to you.

ANY NON-RESIDENTIAL USE OR

COMMERCIAL USE VOIDS ALL

WARRANTIES.

The Great States Corporation

American Lawn Mower Company

830 Webster Street

Shelbyville, IN 46176

Phone 1-800-313-5111

www.earthwisetools.com

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

OPERATOR’S MANUAL

18-IN Lithium Snow Thrower

This product is covered by U. S. patents and other international patents

Rev. 12/19/16

Modelo SN74018

MANUAL DEL OPERARIO

Sopladora de nieve de 460 mm (18 pulg.) de Litio

Este producto está amparado por patentes de EE. UU. y otras patentes internacionales

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE EL FUNCIONAMIENTO, EL MONTAJE,

LAS PIEZAS Y EL MANTENIMIENTO? LLAME AL 1-800-313-5111 ENTRE LAS 8:00 Y LAS 17:00 HS., HORA DEL ESTE

DE LOS ESTADOS UNIDOS.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Este producto fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y seguridad

para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender

el manual del operario antes de usar este producto.

Cargador Cumple con

CA está incluido

(Modelo No. CHL80040)

Los productos eléctricos no se deben desechar junto con los residuos domésticos. Recicle

donde haya centros para tal fin. Consulte a la autoridad local o al distribuidor minorista para

obtener asesoramiento sobre reciclado.

SÍMBOLOS

Algunos de los siguientes símbolos pueden aparecer en este producto. Tenga a bien estudiarlos y aprender su significado.

La adecuada interpretación de estos símbolos le permitirá operar el producto mejor y de manera más segura.

2

Precauciones para su seguridad.

PRECAUCIÓ N: Lea el manual de instrucciones y atienda las instrucciones se seguridad y advertencia.

PRECAUCIÓ N: Retire el enchufe del tomacorriente de inmediato si el cable está dañado o cortado.

APAGUE la máquina, espere hasta que se detenga por completo y retire el enchufe del tomacorriente

antes de realizar alguna tarea de mantenimiento, limpieza o reparación.

PRECAUCIÓ N: Use siempre protecciones para sus ojos y oídos.

Use calzado seguro, resistente y antideslizante.

¡PELIGRO! Pueden ser lanzados objetos a gran velocidad cuando el motor está en funcionamiento. No

pase delante de la máquina cuando está funcionando.

Mantenga a las personas que se encuentran en el lugar a una distancia segura.

Mantenga el cable eléctrico lejos de la barrena. La barrena puede dañar el cable y producir un contacto con

piezas activas.

¡PELIGRO! Cuchillas giratorias. Mantenga manos y pies a una distancia segura.

No colocar la mano debajo de la barrena.

No colocar la mano enfrente del deflector de descarga.

No exponga la unidad a la lluvia ni la use en lugares húmedos.

¡PELIGRO! Riesgos de descargas eléctricas.

No usar en la lluvia. No usar durante tormentas eléctricas.

La page charge ...

EarthWise SN74018 Manuel utilisateur

EarthWise SN74018 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents