Bolens 31AS2P5C565 Le manuel du propriétaire
- Catégorie
- Souffleuses à neige
- Taper
- Le manuel du propriétaire
P. O. Box 1386, 97 KENT AVENUE, KITCHENER, ON N2G 4J1
Printed In USA
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
OPERATOR’S MANUAL
769-06200
0 6. 09.10
Single-Stage Snow Thrower — 2P5 Series
Customer Support
Please do
NOT
return the unit to the retailer from which it was purchased, without first contacting Customer Support.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:
Visit our web at www.bolens.ca◊
Locate your nearest dealer from Customer Support: 1-800-668-1238◊
Contact MTD CANADA • P.O. Box 1386 • 97 Kent Avenue • Kitchener, Ontario, Canada • N2G 4J1◊
To The Owner
1
2
Safe Operation Practices ........................................ 3
Assembly & Set-Up .................................................. 7
Controls .................................................................... 8
Operation ................................................................. 9
Maintenance & Adjustment..................................10
Service .....................................................................12
Troubleshooting .....................................................13
Replacement Parts .................................................14
Warranty .................................................................15
Table of Contents
Thank you for purchasing your new equipment. It was carefully
engineered to provide excellent performance when properly
operated and maintained.
Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain your machine. Please be sure that you, and any other
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.
All information in this manual is relative to the most recent
product information available at the time of printing. Review
this manual frequently to familiarize yourself with the machine,
its features and operation. Please be aware that this Operator’s
Manual may cover a range of product specifications for
various models. Characteristics and features discussed and/or
illustrated in this manual may not be applicable to all models.
The manufacturer reserves the right to change product
specifications, designs and equipment without notice and
without incurring obligation.
If you have any problems or questions concerning the machine,
phone your local service dealer or contact us directly. Customer
Support telephone numbers, website address and mailing
address can be found on this page. We want to ensure your
complete satisfaction at all times.
Throughout this manual, all references to right and left side of the
machine are observed from the operating position.
The engine manufacturer is responsible for all engine-related
issues with regards to performance, power-rating, specifications,
warranty and service. Please refer to the engine manufacturer’s
Owner’s/Operator’s Manual, packed separately with your
machine, for more information.
Thank You
Record Product Information
Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by standing at the operator’s position and looking
down at the rear of the frame. This information will be necessary,
should you seek technical support via our web site, Customer
Support Department, or with a local authorized service dealer.
Mo d e l Nu M b e r
Se r i a l Nu M b e r
Important Safe Operation Practices
2
3
Training
Read, understand, and follow all instructions on the 1.
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
Be familiar with all controls and their proper operation. 2.
Know how to stop the machine and disengage them
quickly.
Never allow children under 14 years of age to operate this 3.
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
Never allow adults to operate this machine without proper 4.
instruction.
Thrown objects can cause serious personal injury. Plan 5.
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
Keep bystanders, pets and children at least 75 feet from the 6.
machine while it is in operation. Stop machine if anyone
enters the area.
Exercise caution to avoid slipping or falling, especially 7.
when operating in reverse.
Preparation
Thoroughly inspect the area where the equipment is to be used.
Remove all doormats, newspapers, sleds, boards, wires and other
foreign objects, which could be tripped over or thrown by the
auger/impeller.
Always wear safety glasses or eye shields during operation 1.
and while performing an adjustment or repair to protect
your eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
Do not operate without wearing adequate winter outer 2.
garments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
Use a grounded three-wire extension cord and receptacle 3.
for all machines with electric start engines.
Disengage all control levers before starting the engine. 4.
Never attempt to make any adjustments while engine is 5.
running, except where specifically recommended in the
operator’s manual.
Let engine and machine adjust to outdoor temperature 6.
before starting to clear snow.
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing foreign objects. Failure to observe the following safety
instructions could result in serious injury or death.
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
4 Se c t i o N 2 — iM p o r t a N t Sa f e op e r a t i o N pr a c t i c e S
Safe Handling of Gasoline
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
Use only an approved gasoline container.a.
Extinguish all cigarettes, cigars, pipes and other b.
sources of ignition.
Never fuel machine indoors. c.
Never remove gas cap or add fuel while the engine is d.
hot or running.
Allow engine to cool at least two minutes before e.
refueling.
Never over fill fuel tank. Fill tank to no more than ½ f.
inch below bottom of filler neck to provide space for
fuel expansion.
Replace gasoline cap and tighten securely.g.
If gasoline is spilled, wipe it off the engine and h.
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
Never store the machine or fuel container inside i.
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).
Allow machine to cool at least 5 minutes before j.
storing.
Never fill containers inside a vehicle or on a truck k.
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
If possible, remove gas-powered equipment from l.
the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the fuel m.
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
Operation
Do not put hands or feet near rotating parts, in the auger/1.
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
The auger/impeller control lever is a safety device. Never 2.
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
The control levers must operate easily in both directions 3.
and automatically return to the disengaged position when
released.
Never operate with a missing or damaged chute assembly. 4.
Keep all safety devices in place and working.
Never run an engine indoors or in a poorly ventilated area. 5.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
Do not operate machine while under the influence of 6.
alcohol or drugs.
Muffler and engine become hot and can cause a burn. Do 7.
not touch. Keep children away.
Exercise extreme caution when operating on or crossing 8.
gravel surfaces. Stay alert for hidden hazards or traffic.
Exercise caution when changing direction and while 9.
operating on slopes.
Plan your snow-throwing pattern to avoid discharge 10.
towards windows, walls, cars etc. Thus, avoiding possible
property damage or personal injury caused by a ricochet.
Never direct discharge at children, bystanders and pets or 11.
allow anyone in front of the machine.
Do not overload machine capacity by attempting to clear 12.
snow at too fast of a rate.
Never operate this machine without good visibility or light. 13.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
Disengage power to the auger/impeller when transporting 14.
or not in use.
Never operate machine at high transport speeds on 15.
slippery surfaces. Look down and behind and use care
when backing up.
If the machine should start to vibrate abnormally, stop 16.
the engine, disconnect the spark plug wire and ground it
against the engine. Inspect thoroughly for damage. Repair
any damage before starting and operating.
Disengage all control levers and stop engine before you 17.
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments,
or inspections.
Never put your hand in the discharge or collector openings. 18.
Do not unclog chute assembly while engine is running.
Shut off engine and remain behind handles until all moving
parts have stopped before unclogging.
Use only attachments and accessories approved by the 19.
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
When starting engine, pull cord slowly until resistance 20.
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.
If situations occur which are not covered in this manual, use 21.
care and good judgment. Contact Customer Support for
assistance and the name of your nearest servicing dealer.
5Se c t i o N 2 — iM p o r t a N t Sa f e op e r a t i o N pr a c t i c e S
Clearing a Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with snow
throwers. Never use your hand to clean out the discharge chute.
To clear the chute:
SHUT THE ENGINE OFF!1.
Wait 10 seconds to be sure the impeller blades have 2.
stopped rotating.
Always use a clean-out tool, not your hands.3.
Maintenance & Storage
Never tamper with safety devices. Check their proper 1.
operation regularly. Refer to the maintenance and
adjustment sections of this manual.
Before cleaning, repairing, or inspecting machine 2.
disengage all control levers and stop the engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting.
Check bolts and screws for proper tightness at frequent 3.
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
Do not change the engine governor setting or over-speed 4.
the engine. The governor controls the maximum safe
operating speed of the engine.
Snow thrower shave plates and skid shoes are subject to 5.
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
Check control levers periodically to verify they engage 6.
and disengage properly and adjust, if necessary. Refer
to the adjustment section in this operator’s manual for
instructions.
Maintain or replace safety and instruction labels, as 7.
necessary.
Observe proper disposal laws and regulations for gas, oil, 8.
etc. to protect the environment.
Prior to storing, run machine a few minutes to clear snow 9.
from machine and prevent freeze up of auger/impeller.
Never store the machine or fuel container inside where 10.
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
Always refer to the operator’s manual for proper 11.
instructions on off-season storage.
Check fuel line, tank, cap, and fittings frequently for cracks 12.
or leaks. Replace if necessary.
Do not crank engine with spark plug removed.13.
According to the Consumer Products Safety Commission 14.
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 60 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
Spark Arrestor
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrester for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
6 Se c t i o N 2 — iM p o r t a N t Sa f e op e r a t i o N pr a c t i c e S
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING AUGER
Do not put hands or feet near rotating parts, in the auger/impeller housing or chute
assembly. Contact with the rotating parts can amputate hands and feet.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal injury.
WARNING—GASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
WARNING— ELECTRICAL SHOCK
Do not use the engine’s electric starter in the rain
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow engine
and muffler to cool before touching.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
Assembly & Set-Up
3
7
NOTE: This Operator’s Manual covers several models. Snow
thrower features may vary by model. Not all features in this
manual are applicable to all snow thrower models and the snow
thrower depicted may differ from yours.
NOTE: All references to the left or right side of the snow thrower
are from the operator’s position. Any exceptions will be noted.
NOTE: Do not use the chute handle to lift the snow thrower.
Assembly
Positioning the Upper Handle
Remove packing material, if present. 1.
Raise the upper handle in the direction shown in Figure 3-1 2.
until it clicks into the operating position. Make sure not to
pinch or crimp the cable.
Tighten the wing knobs. See Figure 3-2.3.
Set-Up
Adding Fuel
Refer to the Engine Operator’s Manual packed with your snow
thrower for information on adding fuel.
Adding Oil
Refer to the Engine Operator’s Manual packed with your snow
thrower for information on adding and checking oil.
Adjustments
Chute Assembly
The pitch of the chute assembly controls the angle at which the
snow is thrown.
Loosen the wing knob found on the left side of the chute 1.
assembly and pivot the upper chute upward or downward
to the desired pitch. Retighten the wing knob before
operating the snow thrower.
Position the chute assembly opening by using the chute 2.
handle to throw the snow in the desired direction. See Fig.
3-3.
Figure 3-1
Figure 3-2
Figure 3-3
Controls & Features
4
8
Auger Control
Chute Control Handle
Chute
Assembly
Shave Plate
Auger
Figure 4-1
NOTE: This Operator’s Manual covers several models. Snow
thrower features may vary by model. Not all features in this
manual are applicable to all snow thrower models and the snow
thrower depicted may differ from yours.
Auger
When engaged, the auger rotation draws snow into the auger
housing and throws it out the discharge chute. Rubber paddles
on the auger also aid in propelling the snow thrower as they
come in contact with the pavement.
Auger Control
Located on the upper handle, the auger control is used to
engage and disengage drive to the auger. Squeeze the control
against the upper handle to engage the auger; release it to
disengage.
Chute Assembly
Rotate the discharge chute to the left or right using chute handle.
The angle of the discharge chute controls the distance that the
snow is thrown. Tilt the discharge chute up for greater distance;
tilt down for less distance. Loosen the hand knob on the side
of the discharge chute to adjust. Tilt the chute to the desired
position, and tighten the knob.
Shave Plate
The shave plate maintains contact with the pavement as
the snow thrower is propelled, allowing snow close to the
pavement’s surface to be discharged.
Primer (if equipped)
Depressing primer forces fuel directly into engine’s carburetor to
aid in cold-weather starting.
Operation
5
9
Starting & Stopping the Engine
WARNING! Always keep hands and feet clear of
moving parts. Do not use a pressurized starting
fluid. Vapors are flammable.
Refer to the Engine Operator’s manual packed with your log
splitter for instructions on starting and stopping the engine.
Engaging the Auger
To engage the auger and start throwing snow, squeeze the 1.
auger control against the handle. Release to stop the auger.
Engaging the Drive
Lift up slightly on the handle to allow the rubber paddles on the
auger to contact the pavement and propel the snow thrower
forward. Pushing downward on the handle will raise the auger
off the ground and stop the forward motion.
NOTE: Excessive upward pressure on the handle will result
in premature wear on the rubber auger blades which are
not be covered by the warranty.
Clearing a Clogged Discharge Chute
WARNING! Never use your hands to clear a
clogged chute assembly. Shut off engine and remain
behind handles until all moving parts have stopped
before using the clean-out tool to clear the chute
assembly.
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with snow
throwers. Never use your hand to clean out the discharge chute.
To clear the chute:
SHUT THE ENGINE OFF!1.
Wait 10 seconds to be sure the impeller blades have 2.
stopped rotating.
Always use a clean-out tool, not your hands.3.
Maintenance & Adjustments
6
10
Adjustments
WARNING! Before servicing, repairing, or
nspecting, disengage the control bail and stop
engine. Removing the key will reduce the possibility
of unauthorized starting of the engine while
quipment is not in use.
Shave Plate
To check the adjustment of the shave plate, place the machine
on a level surface. The wheels, shave plate and auger should all
contact the level surface. Note that if the shave plate is adjusted
too high, snow may blow under the housing. If the shave plate
wears out excessively, or the snow thrower does not self-propel,
the shave plate may be too low and needs to be adjusted.
NOTE: On new snow throwers or machines with a new shave
plate installed, the auger may be slightly off the ground.
To adjust the shave plate proceed as follows:
WARNING: Run the engine completely dry of
gasoline before tipping snowthrower..
Pull the starter cord until resistance is felt. Then tip the 1.
snow thrower back until it rests on the handles.
Loosen the four lock nuts and bolts which secure the shave 2.
plate to the housing. See Fig. 6-1. Move the shave plate to the
desired position and retighten the nuts and bolts securely.
Tip the snow thrower back to the operating position and pull 3.
the starter handle a few times to see if it is difficult to pull.
If the starter is difficult to pull, remove the spark plug and 4.
pull the handle several times to ensure that any oil trapped
in the head is removed.
CAUTION: Oil may come out of the spark plug hole
when it is removed and the starter handle is pulled.
Inspect the spark plug. If it is wet, clean off any oil before 5.
re-installing.
Control Cable
As a result of both the control cable and the auger drive belt
stretching due to wear, periodic adjustments may be necessary. If
the auger seems to hesitate when rotating, proceed as follows:
The upper hole in the control handle provides for an adjustment
in cable tension. To adjust, disconnect the end of control cable
from the bottom hole in the control handle and reinsert it in the
upper hole. Insert the cable from the outside as shown in Fig. 6-2.
Test the snow thrower to see if there is a noticeable difference. If
after the adjustment to the control cable the auger still hesitates
when rotating, see the Service Section for instructions on
replacing the belt.
Chute Assembly
Refer to the Assembly & Set-Up section for instructions on
adjusting the chute assembly.
Maintenance
Lubrication
Lubricate the pivot points on the control handle and the
extension spring at the end of the control cable with a light
oil once every season and before the snow thrower is put into
storage at the end of the season.
Figure 6-1
Side View
Lock Nut
Bolt
Control
Cable
Control
Handle
Figure 6-2
11Se c t i o n 6 — Ma i n t e n a n c e & ad j u S t M e n t S
Off-Season Storage
If the snow thrower will not be used for 30 days or longer, follow
the instructions below.
Store the equipment in a clean, dry area.1.
If storing the snow thrower in an unventilated area, 2.
rustproof the machine using a light oil or silicone to coat
the snow thrower.
Clean the exterior of the engine and the snow thrower.3.
Lubricate pivot points on control handle and extension 4.
spring at end of control cable with a light oil
Refer to engine manual for correct engine storage 5.
instructions.
Service
7
12
Replacing Belt
Remove the belt cover by removing five hex screws. See Fig. 8-1.
Then simply pull the belt off by grasping it from the bottom of
the auger pulley and pulling off. Once you remove the belt from
the pulleys, you can push down on the idler pulley to release the
belt from under belt keeper.
To replace the belt follow these instructions and refer to Fig. 8-2:
Push down on the Idler pulley.1.
Put belt on top of the auger pulley under belt keeper.2.
Thread belt around engine pulley.3.
Push belt over bottom of auger pulley.4.
Reinstall the belt cover removed earlier.5.
Replacing Auger Paddles
The snow thrower auger’s rubber paddles are subject to wear
and should be replaced if any signs of excessive wear are present.
CAUTION: Do NOT allow the auger’s rubber
paddles to wear to the point where portions of the
metal auger itself can come in contact with the
pavement. Doing so can result in serious damage to
your snow thrower.
To change the rubber paddles, proceed as follows:
Remove the existing rubber paddles by unthreading the 1.
self-tapping screws which secure them to the auger. See
Fig. 8-3.
Secure the replacement rubber paddles to the auger using 2.
the hardware removed earlier.
Replacing Shave Plate
The shave plate is attached to the bottom of the auger housing
and is subject to wear. It should be checked periodically. There
are two wearing edges and the shave plate can be reversed.
Refer to Fig. 8-3. To replace or reverse the shave plate proceed as
follows:
Remove the carriage bolts and hex lock nuts which attach 1.
it to the snow thrower housing.
Install new shave plate (or reverse), making sure the heads 2.
of the carriage bolts are on the inside of the housing.
Adjust the shave plate according to instructions above3.
Tighten securely.4.
Idler Pulley
Belt Keeper
Hex Screws
Figure 8-1
Figure 8-2
Engine Pulley
Auger Pulley
1
4
3
2
Self-Tapping Screws
Figure 8-3
Troubleshooting
8
13
Problem Cause Remedy
Loss of power Spark plug wire loose.1.
Vent in gas cap plugged.2.
Firmly connect spark plug wire.1.
Clear vent.2.
Excessive vibration Loose parts or damaged auger.1. Stop engine immediately and disconnect 1.
spark plug wire. Check for possible damage.
Tighten all bolts and nuts. Repair as needed.
If the problem persists, take snow thrower to
an authorized service dealer.
Snow thrower fails to self-
propel
Auger control cable out of adjustment. 1.
Auger drive belt loose or damaged.2.
Adjust auger control cable as shown in 1.
Maintenance & Adjustments section.
Replace auger drive belt.2.
Augers continue to rotate Auger control cable out of adjustment.1. Adjust auger control cable as shown in 1.
Maintenance & Adjustments section.
Unit fails to discharge snow Chute assembly clogged. 1.
Foreign object lodged in auger. 2.
Auger control cable out of adjustment.3.
Auger belt loose or damaged.4.
Stop engine and disconnect spark plug wire. 1.
Clean chute and inside of auger housing with
clean-out tool or stick.
Stop engine immediately and disconnect the 2.
spark plug wire. Remove object from auger.
Adjust auger control cable.3.
Replace auger belt.4.
Replacement Parts
9
14
Phone (800) 800-7310 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).
Parts Manual downloads are also available free of charge at www.mtdproducts.com.
Component Part Number and Description
731-1033 Shave Plate
954-0101A Belt V-Type (2M1 Models)
954-04204 Belt V-Type (2N1 & 2P5 Models)
735-04032 Spiral Crescent
735-04033 Rubber Paddle
753-04472 Replacement Kit (includes 4 crescents,
2 paddles and hardware)
731-05632 Key
746-04237 Clutch Cable
951-10292 Spark Plug
4 YEAR LIMITED WARRANTY
For FOUR YEARS from the date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option, repair or
replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
This warranty does not cover:
Any part which has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper 1.
maintenance or alteration; or
The unit if it has not been operated and/or maintained in accordance with the owner’s instructions furnished with 2.
the unit; or
The engine or motor or component parts thereof which carry separate warranties from their manufacturers. Please 3.
refer to the applicable manufacturer’s warranty on these items; and read engine warranty statement below, or
Batteries and normal wear parts except as noted below. Log splitter pumps, valves and cylinders or component 4.
parts thereof are covered by a one year warranty; or
Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake, 5.
clutch or deck; or
Normal deterioration of the exterior finish due to use or exposure. 6.
Full Ninety Day Warranty on Battery (if equipped): For ninety (90) days from the date of retail purchase, if any battery
included with this unit proves defective in material or workmanship and our testing determines the battery will not hold
a charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.
Additional Limited Thirty Day Warranty on Battery (if equipped): After ninety (90) days but within one hundred
twenty (120) days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective battery, for the original
purchaser, for a cost of one-half (½) of the current retail price of the battery in effect at the date of return.
Full Ninety Days Warranty on Normal Wear Parts: Normal wear parts are defined as belts, blade adaptors, blades,
grass bags, seats, tires, rider deck wheels and clutch parts (friction wheels). These parts are warranted to the original
purchaser to be free from defects in material and workmanship for a period of ninety (90) days from the date of retail
purchase.
How to Obtain Service: Warranty service is available, with proof of purchase, through your local authorized service
dealer or distributor. If you do not know the dealer or distributor in your area, please call, toll free 1-800-668-1238. The
return of a complete unit will not be accepted by the factory unless prior written permission has been extended by MTD
PRODUCTS LIMITED.
Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are the
responsibility of the purchaser. Transportation charges for any part submitted for replacement under this warranty must
be paid by the purchaser unless such return is requested in writing by MTD PRODUCTS LIMITED.
Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited
in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the
sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale of its products.
MTD PRODUCTS LIMITED will not be liable for incidental or consequential loss or damage.
4 YEAR LIMITED WARRANTY ENGINES
This limited warranty doubles the time periods of the engine manufacturer’s limited warranty which is enclosed in the
owner’s information package.
12.08.06
15
16
Notes
16
Notes
GARANTIE LIMITÉE DE QUATRE ANS
MTD PRODUCTS LIMITED s’engage à réparer ou à remplacer gratuitement, à son choix, à l’acheteur initial, toute pièce ou
partie de pièce qui s’avère défectueuse en raison d’un vice de matière ou de fabrication, dans un délai de QUATRE ANS à
partir de la date d’achat au détail au Canada.
Cette garantie ne couvre pas:
Les pièces rendues inutilisables par un emploi incorrect, une utilisation commerciale, un emploi abusif, une 1.
négligence, un entretien incorrect ou une modification;
La machine si elle n’a pas été utilisée et/ou entretenue conformément aux instructions qui l’accompagnaient;2.
Le moteur, le moteur électrique ou l’un de ses composants car ils sont garantis par leurs fabricants respectifs. 3.
Veuillez consulter la garantie qui s’applique à la pièce en particulier; et lisez le paragraphe ci-dessous au sujet de la
garantie des moteurs;
Les batteries et les pièces présentant une usure normale énumérées plus bas. Les pompes, soupapes et cylindres 4.
des fendeuses à bois sont garantis pendant un an;
Les articles d’entretien courant tels que les lubrifiants, filtres, aiguisage de lames et révisions, ou les réglages des 5.
freins, de l’embrayage ou du plateau de coupe;
La détérioration normale de la finition extérieur du fait de l’utilisation de la machine et de son exposition aux 6.
intempéries.
Garantie complète de quatre-vingt-dix jours sur la batterie (le cas échéant): MTD PRODUCTS LIMITED s’engage
à remplacer gratuitement à l’acheteur initial, pour une période de quatre-vingt-dix (90) jours à compter de la date
d’achat au détail, toute batterie fournie avec cette machine qui s’avère défectueuse en raison d’un vice de matière ou de
fabrication et après que nos tests aient confirmé qu’elle ne peut maintenir une charge.
Garantie limitée supplémentaire de trente jours sur la batterie (le cas échéant): MTD PRODUCTS LIMITED s’engage,
à l’expiration de la période de quatre-vingt-dix (90) jours et avant la fin d’une période de cent vingt (120) jours à compter
de la date d’achat, à remplacer la batterie défectueuse à l’acheteur initial, pour la moitié (1/2) du prix de détail en vigueur
de la batterie à la date du retour de celle-ci.
Garantie complète de quatre-vingt-dix (90) jours des pièces à usure normale: Les courroies, adaptateurs de lame,
lames, sacs à herbe, sièges, pneus, roues du plateau de coupe des tondeuses à siège, et pièces d’embrayage (roues de
frottement) sont considérés comme des pièces à usure normale. Elles sont garanties exemptes de vices de matière et de
fabrication à l’acheteur initial pour une période de quatre-vingt-dix (90) jours à partir de la date d’achat au détail.
Pour faire honorer la garantie: Présentez une preuve d’achat à l’atelier de réparations ou au distributeur agréé. Si vous
ne connaissez pas l’adresse de l’atelier de réparations ou du distributeur de votre région, appelez le 1-800-668-1238.
L’usine ne peut accepter le renvoi d’une machine complète si une autorisation n’a pas été accordée par écrit par MTD
PRODUCTS LIMITED.
Frais de transport: Les frais relatifs au transport de toute machine motorisée ou de tout accessoire sont à la charge de
l’acheteur. Les frais de transport d’une pièce quelconque envoyée à des fins de remplacement en vertu de cette garantie
doivent être prise en charge par l’acheteur, sauf si le renvoi de la machine est demandé par écrit par MTD PRODUCTS
LIMITED.
Autres garanties: Toutes les autres garanties, qu’elles soient expresses ou tacites, y compris les garanties tacites de
qualité marchande, se limitent à la durée stipulée dans cette garantie limitée expresse. Les conditions stipulées dans
cette garantie constituent le recours unique et exclusif quant aux obligations de MTD PRODUCTS LIMITED découlant de
la vente de ses produits.
MTD PRODUCTS LIMITED ne peut être tenue responsable pour toute perte ou tout dommage accidentel ou indirect.
GARANTIE LIMITÉE DE 4 ANS DES MOTEURS
Cette garantie limitée double la durée de la garantie limitée du fabricant du moteur qui accompagne la documentation à
l’intention du propriétaire.
12.08.06
15
Pièces de rechange
9
14
REMARQUE: Vous pouvez télécharger un livret contenant la liste complète des pièces détachées adressez-vous au «Service après-
vente» à la page 2. Voir les renseignements qui se trouvent à la page 2 pour localiser les numéros de modèle et de série de votre
machine.
Component No. de pièce et description
2 pales et la boulonnerie)
Dépannage
8
13
Problème Cause Solution
Perte de puissance Fil de la bougie desserré.1.
Chapeau d’échappement du trou d’aération 2.
bouché.
Branchez et serrez le fil de la bougie.1.
Dégagez la glace et la neige du chapeau. 2.
d’aération.
Vibration excessives Pièces desserrées ou vis sans fin 1.
endommagée.
1.
débranchez le fil de la bougie. Vérifiez que la
machine n’est pas endommagée. Serrez tous
les boulons et écrous. Réparez au besoin. Si le
problème persiste, faites vérifier la machine
par une station technique agréée.
La souffleuse n’avance pas Câble d’entraînement à la tarière mal réglé.1.
Courroie d’entraînement à la tarière abîmée 2.
Réglez le câble1. d’entraînement à la tarière.
Voir le chapitre « Entretien et Réglages. ».
Remplacez la courroie d’entraînement.1.
Les tarières continuent à
tourner
Câble d’entraînement à la tarière mal réglé.1.
Courroie d’entraînement à la tarière abîmée 2.
Réglez le câble1. d’entraînement à la tarière.
Voir le chapitre « Entretien et Réglages. ».
Remplacez la courroie d’entraînement.2.
La souffleuse n’évacue pas
la neige
1.
Présence de corps étranger dans la tarière. 2.
Câble d’entraînement à la tarière mal réglé.3.
Courroie d’entraînement de la tarière abîmée
1.
goulotte d’éjection et l’intérieur du logement
de la tarière avec l’outil de dégagement de la
goulotte ou un bâton.
2.
débranchez le fil de la bougie. Dégagez le
corps étranger de la tarière.
Réglez le câble3. d’entraînement à la tarière.
Remplacez la courroie d’entraînement.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Bolens 31AS2P5C565 Le manuel du propriétaire
- Catégorie
- Souffleuses à neige
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Bolens 31AS2P5C565 Owner's manual
Documents connexes
Autres documents
-
MTD 300 Series Manuel utilisateur
-
Cub Cadet 3x Manuel utilisateur
-
-
-
Yardworks 500 Series Manuel utilisateur
-
-
EarthWise SN74022 Le manuel du propriétaire
-
EarthWise SN74018 Manuel utilisateur
-
Ryobi RYSNW00 Le manuel du propriétaire
-
