Fantech 463913 Manuel utilisateur

Marque: Fantech

Modèle: 463913

Taper: Manuel utilisateur

Installation and Operation Manual

Manuel d'installation et d'utilisation

ATMO™ Series

Fresh Air Appliance (FAA)

Appareil à air frais (AAF)

Item #: 463913

Rev Date: 2021-05-14

No. d'article #: 463913

Date de révision: 2021-05-14

Your ventilation system should be installed in conformance with the appropriate provincial requirements or, in the absence of

such requirements, with the current edition of the National Building Code, and / or ASHRAE’s “Good Engineering Practices”.

Votre système de ventilation doit être installé conformément aux exigences de la province où vous habitez ou, à défaut de

telles exigences, conformément à l’édition actuelle du Code national du bâtiment du Canada ou aux « méthodes d’ingénierie

appropriées » de l’ASHRAE.

Fantech reserves the right to modify, at any time and without notice, any or all of its products’ features, designs,

components and specifications to maintain their technological leadership position.

Please visit our website www.fantech.net for more detailed technical information.

Fantech se réserve le droit de modifier partiellement ou entièrement, en tout moment et sans préavis, les

caractéristiques, la conception, les composants et les spécifications de ses produits, afin de conserver sa

position de leader de technologie.

S'il vous plaît visitez notre site siteweb www.fantech.net pour des informations techiques plus détaillées.

United States

10048 Industrial Blvd., Lenexa, KS, 66215

Tel.: 800.747.1762 • Fax: 800.487.9915

Canada

50 Kanalflakt Way, Bouctouche, NB, E4S 3M5

Tel.: 800.565.3548 • Fax: 877.747.8116

PARTS IN THE BOX

Fresh Air Appliance, 1 pc

Hanging Chain Kit, 1 pc

Hardware Kit, 1 pc

Drain Hose Kit, 1 pc

Operation and Installation Manual, 1 pc

PIÈCES DANS LA BOÎTE

Appareil à air frais, 1 pc

Kit de suspension, 1 pc

Vis et matériel d'assemblage, 1 pc

Tuyau d’évacuation , 1 pc

Manuel d'installation, 1 pc

ATMO 150H

is not

ENERGY STAR

listed.

Note Warning/

Important

note

Information Technical

information Practical tip

PLEASE READ AND SAVE THESE INSTRUCTIONS

Before installation careful consideration must be given to how this system will operate if connected to

any other piece of mechanical equipment, i.e. a forced air furnace or air handler operating at a higher

static pressure. After installation, the compatibility of the two pieces of equipment must be conrmed

by measuring the airow of the Fresh Air Applliance using the balancing procedure found in this manual.

It is always important to assess how the operation of any FAA may interact with vented combustion equipment (i.e.

Gas Furnaces, Oil Furnaces, Wood Stoves, etc.)

Products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100%

free of defects. Even reliable products will experience occasional failures, and this possibility should be recognized

by the user. If these products are used in a life support ventilation system where failure could result in loss or injury,

the user should provide adequate back-up ventilation, supplementary natural ventilation or failure alarm system, or

acknowledge willingness to accept the risk of such loss or injury.

Your ventilation system should be installed in accordance with the local building code that is in effect, in absence

of such requirements, it is recommenced to check with local authorities having jurisdiction in your area prior to

installing this product.

TABLE OF CONTENTS

DETERMINING YOUR AIRFLOW REQUIREMENT ..................................................... 4

INSTALLATION EXAMPLES

Fully dedicated system ................................................................ 5

Partially dedicated system .............................................................. 6

Simplified Installation ................................................................. 7

EXTERIOR DUCTING INSTALLATION

Weatherhood Location ................................................................. 8

Installing the ducting to the weatherhood ................................................... 8

INTERIOR DUCTING INSTALLATION

General Tips ........................................................................ 9

Installing duct to FAA.................................................................. 9

Supply & Exhaust Air Grilles Location....................................................... 9

FAA INSTALLATION ........................................................................ 10

AIRFLOW ADJUSTMENT & BALANCING ...........................................................12

LOW VOLTAGE CONTROL SYSTEMS ............................................................. 13

WIRING DIAGRAM ......................................................................... 15

TROUBLESHOOTING .........................................................................17

FAA MAINTENANCE CHART ....................................................................18

PARTS LIST ...............................................................................37

Room classification Number of rooms CFM (L/s)

CFM Required

Master bedroom x 10 L/s (20 CFM) =

Basement yes or no =

Bedrooms x 5 L/s (10 CFM) =

Living room x 5 L/s (10 CFM) =

Others x 5 L/s (10 CFM) =

Kitchen x 5 L/s (10 CFM) =

Bathroom x 5 L/s (10 CFM) =

Laundry room x 5 L/s (10 CFM) =

Utility room x 5 L/s (10 CFM) =

Total Ventilation Requirements (add last column ) =

if yes add 10 L/s (20 CFM)

if no = 0

1 CFM = 0.47 L/s

1 L/s = 2.13 CFM

Room Count Method

DETERMINING YOUR AIRFLOW REQUIREMENT

ASHRAE method

Ventilation Air requirements

Floor area Bedrooms

1 2 3 4 5

Ft2m2CFM L/s CFM L/s CFM L/s CFM L/s CFM L/s

<500 <47 30 128 38 18 45 21 53 25 60 28

501-1000 47-93 45 21 53 24 60 28 68 31 75 35

1001-1500 94-139 60 28 68 31 75 35 83 38 90 42

1501-2000 140-186 75 35 83 38 90 42 98 45 105 49

2001-2500 187-232 90 42 98 45 105 49 113 52 120 56

2501-3000 233-279 105 49 113 52 120 56 128 59 135 63

3001-3500 280-325 120 56 128 59 135 63 143 66 150 70

3501-4000 326-372 135 63 143 66 150 70 158 73 165 77

4001-4500 373-418 150 70 158 73 165 77 173 80 180 84

4501-5000 419-465 165 77 173 80 180 84 188 87 195 91

* ASHRAE 62.2-2016 Table 4.1, Ventilation and Acceptable Indoor Air Quality in Low-Rise Residential Buildings.

Bathroom: If the FAA is going to provide the required local exhaust ventilation for each bathroom with each a continuous 20 CFM

(10 L/s), this ventilation rate can be considered as part of the whole-building ventilation rate.

INSTALLATION EXAMPLES

The way your heat/energy-recovery ventilator is installed can make a significant difference to the electrical

energy you use. To minimize the electricity use of the heat/energy-recovery ventilator, a stand-alone fully

ducted installation is recommended. If you choose a simplified installation that operates your furnace air

handler for room-to-room ventilation, an electrically efficient furnace that has an electronically commutated

(EC) variable speed blower motor will minimize your electrical energy consumption and operating cost.

Example only – duct configuration may differ depending on the model.

FULLY DEDICATED SYSTEM

BEST FOR NEW CONSTRUCTION

1. Stale air is drawn from

key areas of the home

requiring local exhaust

(bathroom, kitchen,

laundry room).

2. Fresh air is distributed

directly to habitable

rooms in the house

(bedrooms, living room)

3. The FAA’s airflow must

be balanced after

installation using the

procedure found in the

section “AIRFLOW

BALANCING”

Suggested installation for:

• Hydronic baseboard

• Inoor heating

• Electric baseboard

• Mini split heat pump

Benets: Provides the best

fresh air distribution in the

house; lowest operation cost

since the furnace/air handler

unit is not needed.

FAA ducting for fully Dedicated System

* Ductwork layout may dif-

fer depending on model

Air from inside

* Unit air flow should be balanced while FAA is on "Normal" speed and

furnace blower is running.

Stale air to

outside

Fresh air from

outside

Fresh air to

living areas

INSTALLATION EXAMPLES (CONT'D)

DIRECT CONNECTION of the FRESH air to living area to the RETURN PLENUM

of the AIR HANDLER (Stale air drawn from key areas of home)

PARTIALLY DEDICATED SYSTEM (BETTER)

Suggested installation for:

• Central furnace (air

handling unit or central air

conditioners)

• When ducting fresh air to

living area is not possible or

practical, i.e. expensive or

when the central AHU will

operate year-round.

Benets: Conditions the fresh

air prior to

distributing it throughout the

house

1. In order to provide proper distribution of the fresh air, it is

recommended that the furnace blower be set to run continuously or

interconnected with FAA. See furnace electrical connection on page

16.

2. Stale air is drawn from key areas of the home (bathroom, kitchen,

laundry room).

3. Fresh air is supplied to the return air plenum of the furnace.

4. Due to the difference in pressure between the FAA and the equipment

it is being connected to the FAA's airflow must be balanced on site,

using the procedure found in the section “AIRFLOW BALANCING”

* In the case of a multi-zone system, please contact Fantech customer

service prior to installing any installation type requiring the use of the

furnace interlock"

FAA/Furnace ducting for Partially Dedicated System

Air from inside

* Unit air flow should be balanced while FAA is on "Normal" speed and

furnace blower is running.

Air return

Cold air

return

* Ductwork layout may dif-

fer depending on model

Stale air to

outside

Fresh air from

outside

Fresh air to

living areas

Fantech fresh air applicance (FAA or HRV/ERV) that use a supply fan shutdown for frost

prevention do not include an outdoor air motorized damper. If you are using a simplied

installation, i.e. connecting the FAA supply air duct to a furnace's return air duct, the FAA

must operate continuously. When the FAA is turned off, no warm exhaust air will ow

through the FAA but the furnace's fan will continue to draw in outdoor air directly into the

furnace. If it's cold outside, cold air will be introduced, without re-heating, directly into

the furnace.

If the FAA is installed such that the homeowner may turn off the FAA during the winter, we

recommend installing a motorized damper between the FAA's supply air and the furnace's

return air duct that closes when the FAA is not operating. See wiring diagram (gure 1).

You may also choose to use a Fantech FAA that uses a recirculation defrost that incorpo-

rates an outdoor air damper.

Damper

Motor

24 VAC Transformer

COM NO

HRV Furnace interlock

See page 16.

24V

120V

Figure 1

*Transformer and Damper motor not included

Make sure the FAA is

capable of meeting the

required airow rate.

INSTALLATION EXAMPLES (CONT'D)

DIRECT CONNECTION of both the FAA SUPPLY AIR STREAM and EXHAUST AIR STREAM

to the FURNACE COLD AIR RETURN

SIMPLIFIED INSTALLATION

(GOOD)

(RETURN/RETURN METHOD)

Suggested installation for:

• When bathroom and kitchen

already have local exhaust

system

• May be suitable for

retrotting

Benets: Least expensive

installation type

1. Furnace blower must operate when ventilation from FAA is required. The furnace should

be set to run continuously or interlocked with FAA. See furnace electrical connection

on page 16.

2. A minimum separation of 1m (39’’) is recommended between the two direct

connections.

3. In order to prevent exhausting any fresh air, the FAA's exhaust air connection should be

upstream of the FAA's supply air connection when ducting to the furnace’s cold air return.

4. Due to the difference in pressure between the FAA and the equipment it is being

connected to the FAA's airflow must be balanced on site, using the procedure found in the

section “AIRFLOW BALANCING”

* In the case of a multi-zone system, please contact Fantech customer

service prior to installing any installation type requiring the use of the

furnace interlock"

Air from inside

* Unit air flow should be balanced while FAA is on "Normal" speed and

furnace blower is running.

1 m (3' 3")

min.

recommended

Cold air

return

* Ductwork layout may dif-

fer depending on model

FAA/Furnace ducting for Simplified Installation - Option 1

Stale air to

outside

Fresh air from

outside

Fresh air to

living areas

Fantech fresh air appliances (FAA) that use a supply fan shutdown for frost prevention do

not include an outdoor air motorized damper. If you are using a simplied installation, i.e.

connecting the FAA supply air duct to a furnace's return air duct, the FAA must operate

continuously. When the FAA is turned off, no warm exhaust air will ow through the FAA

but the furnace's fan will continue to draw in outdoor air directly into the furnace. If it's

cold outside, cold air will be introduced, without re-heating, directly into the furnace.

If the FAA is installed such that the homeowner may turn off the FAA during the winter, we

recommend installing a motorized damper between the FAA's supply air and the furnace's

return air duct that closes when the FAA is not operating. See wiring diagram (gure 1).

You may also choose to use a Fantech FAA that uses a recirculation defrost that incorpo-

rates an outdoor air damper.

Damper

Motor

24 VAC Transformer

COM NO

ERV Furnace interlock

See page 16.

24V

120V

Figure 1

*Transformer and Damper motor not included

Motorized

damper

1 m (3' 3")

min.

recommended

Air return

EXTERIOR DUCTING INSTALLATION

WEATHERHOOD LOCATION

• Decide where your intake and exhaust hoods will be located.

Locating the Intake Weatherhood

• Should be located upstream (if there are prevailing winds) from the

exhaust outlet.

• At a minimum distance to 900 mm (3') away from dryer vents and furnace

exhaust (medium or high efficiency furnaces), driveways, oil fill pipes, gas

meters, or garbage containers.

• At a minimum height of 460mm (18’’) above the ground, or above the level

of expected snow accumulation.

• Ideally, keep weatherhoods 1m (3') from corners.

• Do not locate in the garage, attic, crawl space, or underneath deck.

Locating the Exhaust Weatherhood

• At least 460mm (18") above ground or above the depth of expected snow accumulation

• Ideally, keep weatherhoods 1m (3') from corners.

• Not near a gas meter, electric meter or a walkway where fog or ice could create a hazard

• Do not locate in a garage, workshop or other unheated space

INSTALLING THE DUCTING TO THE WEATHERHOODS

A well designed and installed ducting system will allow the FAA to operate at its

maximum efficiency. The inner liner of the flexible insulated duct must be secured to the

sleeve of the weatherhood (as close to the outside as possible) and to the appropriate duct

connection on the FAA. The insulation should remain full and not crushed. The outer liner,

which acts as a vapor barrier, must be completely sealed to the outer wall and the FAA

using tape and/or caulking. A good bead of high quality caulking (preferably acoustical

sealant) will seal the inner flexible duct to both the FAA duct connection and the

weatherhood prior to securing them.

To minimize airflow restriction, the flexible insulated duct that connects the two outside

weatherhoods to the FAA should be stretched tightly and be as short as possible.

Twisting or folding the duct will severely restrict airflow.

See “Installation Diagram Examples” for installation examples.

1 Using the duct connection of

the outside hood, outline the

intake & exhaust holes to be

cut. The holes should be slightly

larger than the duct connection

to allow for the thickness of the

insulated flexible duct. Cut a

hole for both the intake and

exhaust hoods.

3 Push the hood into the opening

and then attach the hood to the

outside wall with mounting

screws.

Repeat the installation

procedure for both the supply

and exhaust hoods.

2 Pull the insulated flexible duct

through the opening until it is

well extended and straight.

Slide the duct’s inner vinyl sleeve

over the hood duct connection

and secure. Pull the insulation

over the duct and pull the vapor

barrier over the sleeve. Secure

with appropriate tape or

sealant.

4 Using a caulking gun, seal

around both hoods to prevent

any leaks.

STEPS FOR HOOD INSTALLATION:

36" (1m)

INTAKE

OUTSIDE CORNER INSIDE CORNER

EXHAUST

18" (460mm) 18" (460mm)

3' (900mm)

min.

36” (1m)

REQUIRES A WEATHERHOOD

WITH A BACKDRAFT

DAMPER ON THE EXHAUST

SIDE.

INTERIOR DUCTING INSTALLATION

• To maximize airflow through the ductwork system, all ducts should be kept short and have as few bends or elbows as possible.

• 45º elbows are preferable to 90º.

• Use “Y“ ducts instead of “T” ducts whenever possible.

• All duct joints must be fastened with screws or duct sealant and wrapped with aluminum foil duct tape to prevent leakage.

• Galvanized ducting from the FAA to the living areas in the house is recommended whenever possible, although flexible ducting

can be used in moderation when necessary.

• To avoid possible noise transfer through the ductwork system, a short length (approximately 300 mm, 12’’) of nonmetallic flexible

insulated duct should be connected between the FAA and the supply/exhaust ductwork system.

• The main supply and return line to/from the FAA must have the same diameter as the duct connection or larger.

• Branch lines to the individual rooms may be as small as 100 mm (4’’).

Installing ducting to FAA

Warning: Always fix and secure the 6" collars with the screws supplied. Avoiding this critical step the unit will accumulate condensation.

Tip to Installer: To ensure a better installation and to avoid an undesired bend in the duct, align the duct with the collar before securing over the four

hooks.

The fresh air from outside and the Exhaust air to outside from the termination ducts to the FAA must be fully insulated of thermal insulation ducts to

minimize heat loss and gain. All tapes, mastics, and nonmetallic clamps used for field installation of flexible ducts shall be listed and labeled to Standard

UL 181B - Closure Systems for Use With Flexible Air Ducts and Air Connectors.

Air Connector A category of flexible duct not meeting the requirements of an Air Duct per UL 181 Standard (not tested for flame penetration, puncture

and impact) and having limitations on use, length and location as defined by NFPA 90A and 90B. Air Connectors are identified by a “round shape” listing

label of the listing agency.

Air Duct A category of flexible duct tested and classified as to the Surface Burning Characteristics in accordance with the UL 181 Standard. Air Ducts

are identified by a “rectangular shape” listing label of the listing agency.

To ensure quiet operation of ENERGY STAR qualified FAA, each product should be installed using sound attenuation techniques appropriate for the

installation. Once insulated flex is attached to the collar, slide collar in keeper section, fixed collar to the unit with four screws supplied in installation

kit to insure a proper seal.

Warning: To reduce air leakage in the final installation always seal the joint between all collars and keepers with aluminum tape or mastic.

Supply air grilles location

In homes without a forced air furnace, fresh air should be supplied to all habitable rooms, including bedrooms and living areas. It should be supplied

from high wall or ceiling locations. Grilles that diffuse the air comfortably are recommended. In homes with a forced air furnace, you may want to connect

the FAA to the furnace ductwork (see information below).

Exhaust air grilles location

The stale air exhaust system is used to draw air from the points in the house where the worst air quality problems occur. It is recommended that return

air ducts be installed in the bathroom, kitchen, and laundry room. Additional return air ducts from strategic locations may be installed. The furnace

return duct may also be used to exhaust from. In this method, the exhaust air is not ducted back from bathrooms, kitchens, etc to the HRV with

“dedicated lines”.

Insert vinyl duct over the hooks

and seal with a Tie wrap

Insert insulation inside the double

collar.

Finish by taping the vapor

barrier to the collar to insure

proper seal.

Slide collar on the unit. Fix and secure with four screws supplied

and seal all joints.

As per building codes and installation requirements for combustion appliances:

Air return ducts, or openings for air return, should not be placed in enclosed spaces containing combustion

appliances that are subject to spillage.

FAA INSTALLATION

LOCATION

The FAA must be located in a conditioned space where it will be possible to conveniently service the unit. Typically

the FAA would be located in the mechanical room or an area close to the outside wall where the weatherhoods will

be mounted. If a basement area is not convenient or does not exist, a utility room may be used.

Attic installation must meet the following conditions:

• Attic temperature must be above freezing conditions at all times and for best performance should be 12°C

(54 °F).

• The condensate drain (if included) must be installed so that the condensate drains and is protected from freezing.

• The attic is easily accessible for equipment maintenance and inspection.

Connecting appliances to the FAA is not recommended. These include:

• Clothes dryer

• Range top

• Stovetop fan

• Central vacuum system

• Bathroom exhaust fans unless they are specifically designed for this purpose

These appliances may cause lint, dust or grease to collect in the FAA, damaging the unit.

Connecting any of these types of appliances to the

FAA will void your warranty.

Mounting- Chain mount

• Have a nearby power supply

(120 volts, 60Hz)

• Choose a location which

allows the possibility

of mounting the unit to

supporting beams.

• The unit should be level

in order to allow proper

condensate drainage

• To minimize noise, do not

install unit in living area

• Ensure proper drainage

1 Place fastening hooks on

the strapping board or

the oor joists.

2 Take at screwdriver and

slightly pull on punched out

tab. Put chain link under

hook.

4 Install a spring on each

chain. Hook the spring

in the links so a loop is

created in the chain. The

spring will then support the

unit's weight and absorb

vibrations.

3 Hang the unit by slipping

a link onto the hanging

hooks, making sure the

unit is level.

INSTALLING DRAIN LINE

Insert the threaded drain adapter thru the bottom of the FAA and hand tighten the plastic nut, and with a wrench tighten the nut another half turn to assure

a better seal.

Install the condensate line (included in drain kit). Insert condensate tubing by pushing clear plastic line over drain adapter. Make condensate trap by

looping the clear plastic tubing. This procedure is to avoid foul odor to enter the FAA.

The drain nipple is placed upside down in the unit to prevent it being damaged during shipping or the installation of the unit.

The Switch on the electrical box is used to toggle between STANDBY, REDUCED speed and NORMAL speed modes.

Place the unit in NORMAL speed to perform the balancing.

Make a loop in condensate line, not be subject to

freezing temperatures.

Use a condensate pump if you don’t have access to a drain.

If outdoor air temperature is above 32°F (0°C) at the extract air (30% RH/72°F, 30% RH /22°C), no drain line installation is required.

If this is the case keep the drain spout as shipped from factory with the cap.

Airflow balancing

Balancing must be completed using the Fantech ECO-Touch®

Programmable Touch Screen Wall Control

ENTERING BALANCING MODE

In the options menu during the initial 5 second countdown

sequence, long press on "ECO" area for 5 seconds to

enter basic balancing mode. The supply and exhaust

fans are adjusted on high speed only and the offsets

are proportionally applied to the medium and low speed

automatically.

STAGE 1

(ADJUST LEVEL OF EXHAUST FAN IN HIGH

SPEED):

• In this step, balance exhaust fan and

measure airow on the exhaust air side

• Pressing on "up" or "down" will adjust the fan

speed in increments of 1%.

• Once the desired exhaust airow is reached,

press on "next" and move on to the next

stage.

STAGE 2

(BALANCE SUPPLY FAN ONLY IN HIGH

SPEED):

• In this step, balance supply fan and measure

airow on the supply air side

• Pressing on "up" or "down" will adjust the fan

speed in increments of 1%.

• Once happy with the outcome, press on

"next" to complete balancing

• The supply and exhaust offset values will be

proportionally applied to low and medium

speed as well.

Fresh Air

from Outside

Stale Air

to Outside

Stale Air

from Home

Fresh

Air

Stale

Air

Fresh Air

to Home

Remove all four (4)

nylon knock out seals.

Do not discard.

LOW

HIGH

Aspiration

d'air frais

Évacuation

d'air vicié

Aspiration

d'air vicié

Air frais

Air vicié

Distribution

d'air frais

BASBASBAS

BAS

BASBAS

HAUT

HAUTHAUT

HAUT

HAUTHAUT

Enlever les quatre (4)

bouchons de nylon.

Ne pas les jeter.

Pressure / Pression Fresh air / Air frais Stale air / Air vicié

IN. W.G. Pascal CFM L/s CFM L/s

PO. d’eau (Pa) PCM PCM

0.36 90 216 102 - -

0.34 85 209 99 222 105

0.32 80 200 94 214 101

0.30 75 192 91 207 98

0.28 70 183 86 198 93

0.26 65 173 82 189 89

0.24 60 163 77 180 85

0.22 55 153 72 170 80

0.20 50 142 67 159 75

0.18 45 131 62 148 70

0.16 40 119 56 136 64

0.14 35 107 50 124 59

0.12 30 95 45 111 52

0.10 25 82 39 97 46

0.08 20 68 32 83 39

0.06 15 55 26 69 33

0.04 10 55 26 54 25

Balancing chart 2.0Balancing chart 1.5

Pressure / Pression Fresh air / Air frais Stale air / Air vicié

IN. W.G. Pascal CFM L/s CFM L/s

PO. d’eau (Pa) PCM PCM

0.60 149 186 88 187 88

0.58 144 182 86 184 87

0.56 139 177 84 180 85

0.54 135 172 81 176 83

0.52 130 167 79 173 82

0.50 125 162 76 169 80

0.48 120 157 74 165 78

0.46 115 152 72 161 76

0.44 110 146 69 156 74

0.42 105 141 67 152 72

0.40 100 136 64 147 69

0.38 95 130 61 143 67

0.36 90 125 59 138 65

0.34 85 119 56 133 63

0.32 80 113 53 128 60

0.30 75 107 50 123 58

0.28 70 102 48 117 55

0.26 65 96 45 112 53

0.24 60 90 42 106 50

0.22 55 84 40 100 47

0.20 50 78 37 94 44

0.18 45 71 34 88 42

0.16 40 65 31 82 39

0.14 35 59 28 76 36

0.12 30 52 25 69 33

0.10 25 46 22 62 29

0.08 20 39 18 56 26

0.06 15 33 16 49 23

AUTO MANUAL

OPTIONS

AUTO MANUAL

OPTIONS

AUTO MANUAL

OPTIONS

0 %

ADJUST

AUTO MANUAL

OPTIONS

0 %

BALANCE

WALL CONTROLS

CENTRAL CONTROLS

These cannot be used with another central control

*Maintain polarity between control and FAA

(+ → + ; - → -)

ECO SERIES* FEATURES CONNECT TO

ECO-Touch® • Our most complete, yet easy-to-use control system

• Sleek design with backlight touchscreen LCD

• ECO mode selects the best operating mode and speed for the season, minimizing energy use associated with

ventilation

• Set preferred indoor relative humidity range and ventilation mode for day and night conditions

• No battery to replace, all programmed settings are retained during power outages

• Maintenance reminder indicator

• Error code messages reduce troubleshooting time

→

D+

ECO-TouchIAQ • Integrated VOC Sensor

• Our most complete, yet easy-to-use control system

• Sleek design with backlight touchscreen LCD

• ECO mode selects the best operating mode and speed for the season, minimizing energy use associated with

ventilation

• Set preferred indoor relative humidity range and ventilation mode for day and night conditions

• No battery to replace, all programmed settings are retained during power outages

• Maintenance reminder indicator

• Error code messages reduce troubleshooting time

ECO-Feel • ECO mode selects the best operating mode and speed for the season, minimizing energy use associated with

ventilation

• Integrated VOC Sensor

• No battery to replace, all programmed settings are retained during power outages

1. Ensure that unit is not plugged when connecting the control

2. Recirculation mode is only available with the Flex100H ES, HERO series and the models with the “R” sufx at the end of the model

number.

The wiring connectors can be removed for easier connection.

* Please see instruction manuals for individual controls for proper wiring and set up of control systems.

Installation of a user-accessible control with your product model will improve comfort and may significantly reduce the product model’s energy use

AUXILIARY CONTROL –These controls can be paired with central controls or combined together.

*Maintain polarity between control and FAA

(+ → + ; - → -)

RTS SERIES FEATURES CONNECTS TO

• Wireless timer

• Can only be paired with the ECO-TouchIAQ

• 20/40/60 minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

Connects wireleslly to the

RTS2* • 20- minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

-T

RTS5* • 20/40/60 minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

WALL CONTROLS (CONT'D)

MDEH SERIES FEATURES CONNECT TO

MDEH1 • Rotary dial Dehumidistat

• Multiple units can be used

• We recommend setting the relative humidity above 80% during the summer

EDF SERIES FEATURES CONNECTS TO

EDF7 • MODE button provides 3 modes of operations: Ventilation , Recirculation and Standby

• User selected fan speed: Reduced, Medium, Normal and 20 minutes per hour

• AUTO setting allows the homeowner to deactivate the dehumidistat

• When the humidity exceeds the desired setpoint, the ventilation system operates at normal speed

• Once the desired humidity level is achieved, your ventilation system resumes to its previous mode of

operation.

EDF1 • Press button once for continuous Reduced speed

• Press button twice and the unit will cycle 20 minutes ON/ 40 minutes OFF and repeat

• EDF1 – Press button a third time and the system will run continuously on HIGH speed

Fantech

Model

ONON

ON ON

LOW SPEEDS

90V75V

J4J5J6

WIRING DIAGRAM - ATMO PRODUCT LINE

Observe polarity on all accessory

controls where applicable.

WR G Y

Standard Furnace Interlock Wiring

THERMOSTAT

TERMINALS

FURNACE

24-VOLT

TERMINAL BLOCK

FOUR

WIRE

TWO WIRE

heating only

TWO

WIRE

COOLING SYSTEM

WR G Y

Alternate Furnace Interlock Wiring

THERMOSTAT

TERMINALS

FURNACE

24-VOLT

TERMINAL BLOCK

FOUR

WIRE

TWO WIRE

heating only

TWO

WIRE

COOLING SYSTEM

WIRE JOINT

WIRING DIAGRAM (CONT'D)

WIRING DIAGRAM TO

FURNACE

FOR A FURNACE

CONNECTION TO

A COOLING SYSTEM:

On some newer furnaces and older

thermostats, energizing the R and

G terminal at the furnace has the

effect of energizing the Y at the

thermostat and thereby turning on

the cooling system. If you identify this

type of thermostat, you must use the

“Alternate Furnace Interlock Wiring”

Standard Accessory Control Contact

Alternative Accessory Control Contact

As per building codes and installation requirements for combustion appliances:

Air return ducts, or openings for air return, should not be placed in enclosed spaces containing combustion

appliances that are subject to spillage.

TROUBLESHOOTING

Problem Causes Solutions

Air is too dry Dehumidistat control is set too low Increase the desired level of humidity. Change ventilation mode from

continuous mode to standby.

FAA out of balance Have contractor balance FAA airows

Air is too humid Dehumidistat control is set too high Reduce the desired level of humidity. Combine this with the use of continuous

exchange mode.

Sudden change in temperature Wait until outside temperature stabilizes (winter). Heating will also improve

situation.

Storing too much wood for heating Store a majority of your wood outside. Even dried, a cord of wood contains

more than 20 gallons of water.

Dryer vent exhaust is inside home Make sure the dryer vent is exhausting outside.

Poor air circulation near windows Open curtains or blinds.

FAA out of balance Have contractor balance FAA airows

Well sealed basement door is closed Open the door or install a grill on the door.

Failed damper system may be stuck in recirculation

mode

Check defrost damper. If damper is always blocking incoming fresh air, have

contractor verify damper system.

Persistent condensation

on window

Improper adjustment of dehumidistat control Reduce the desired level of humidity. Combine this step with use of continuous

exchange mode.

FAA out of balance Have contractor balance FAA

Poor air circulation near windows Open curtains or blinds.

Poor Air Flows 1/4" (6mm) mesh on the outside hoods is plugged Clean exterior hoods or vents

Filters plugged Remove and clean lter

Core obstructed Remove and clean core

Indoor grilles closed or blocked Check and open grilles

Inadequate power supply at site Have electrician check supply voltage

Ductwork is restricting airow Check duct installation

Improper speed control setting Increase the speed of the FAA (i.e. change unit control from REDUCED to NORMAL

speed)

FAA airow improperly balanced Have contractor balance FAA airows

Ducting has fallen down or been disconnected from FAA Have contractor reconnect ducting

Supply air feels cold Poor location of supply grilles, the airow may irritate

the occupant

Locate the grilles high on the walls or under the baseboards, install ceiling

mounted diffuser or grilles so as not to directly spill the supply air on the

occupant (eg. Over a sofa)

Turn down the FAA supply speed. A small duct heater (1kw) could be used to

temper the supply air

Placement of furniture or closed doors is restricting the movement of air in

the home

Outdoor temperature extremely cold If supply air is ducted into furnace return, the furnace fan may need to run

continuously to distribute ventilation air comfortably

FAA and/or Ducts frosting up FAA air ows are improperly balanced Have HVAC contractor balance the FAA airows

Malfunction of the FAA defrost system Note: minimal frost build-up is expected on the core before unit initiates

defrost cycle functions

Condensation or Ice Build Up in

Insulated Duct to the Outside

Incomplete vapor barrier around insulated duct Tape and seal all joints

A hole or tear in outer duct covering Tape any holes or tears made in the outer duct covering

Ensure that the vapor barrier is completely sealed.

LED is ashing Everything is in good operations

LED is not ashing No Power is being transmitted to the Control Board Make sure unit is plugged.

Transformer may need replacing.

Note: It is best to get the unit checked by a certied HVAC Contractor/Technician.

Limited Warranty

• The Heat recovery aluminum core

has a Limited Lifetime Warranty.

• The warranty is limited to 5 years on

parts and 7 years on fans from the

date of purchase, including parts

replaced during this time period. If

there is no proof of purchase

available, the date associated with

the serial number will be used for

the beginning of the warranty period.

• The fans found in all Fantech FAAs

require no lubrication, and are

factory balanced to prevent vibration

and promote silent operation.

• The limited warranty covers

normal use. It does not apply to

any defects, malfunctions or

failures as a result of improper

installation, abuse, mishandling,

misapplication, fortuitous

occurrence or any other

circumstances outside Fantech’s

control.

• Inappropriate installation or

maintenance may result in the

cancellation of the warranty.

• Any unauthorized work will result in

the cancellation of the warranty.

• Fantech is not responsible for any

incidental or consequential

damages incurred in the use of the

ventilation system.

• Fantech is not responsible for

providing an authorized service

centre near the purchaser or in

the general area.

• Fantech reserves the right to supply

refurbished parts as replacements.

• Transportation, removal and

installation fees are the responsibility

of the purchaser.

• The purchaser is responsible to

adhering to all codes in effect in his

area.

* This warranty is the exclusive and only warranty

in effect relative to the ventilation system and all

other warranties either expressed or implied are

invalid.

FAA MAINTENANCE CHART

Maintenance Required Recommended Frequency Date Maintenance Performed

Check and Clean Filters Every 3 months or if

dirty

Check Heat Recovery

Core

Every 6 months

Check Drain Pan and

Lines

Every 3 months

Vacuum the Inside of the

Unit

Annually

Clean and Un-block

Outside

Hoods

Annually

Clean and Inspect Duct

Work

Annually

General Servicing by a

Qualied Contractor

Annually

* Schedule may be altered to meet your own needs. More frequent servicing may be required depending on the

severity of your home's indoor and outdoor environments.

Contractor Telephone Number Date Serviced

Manuel d'installation

ATMO Series

Appareil à air frais (AAF

No. d'article #: 463913

Date de révision: 2021-05-14

Votre système de ventilation doit être installé conformément aux exigences de la province où vous habitez ou, à défaut de

telles exigences, conformément à l’édition actuelle du Code national du bâtiment du Canada ou aux « méthodes d’ingénierie

appropriées » de l’ASHRAE.

Fantech se réserve le droit de modifier partiellement ou entièrement, en tout moment et sans préavis, les

caractéristiques, la conception, les composants et les spécifications de ses produits, afin de conserver sa

position de leader de technologie.

S'il vous plaît visitez notre site siteweb www.fantech.net pour des informations techiques plus détaillées.

United States

10048 Industrial Blvd., Lenexa, KS, 66215

Tél.: 800.747.1762 • Fax: 800.487.9915

Canada

50 Kanalflakt Way, Bouctouche, NB, E4S 3M5

Tél.: 800.565.3548 • Fax: 877.747.8116

PIÈCES DANS LA BOÎTE

Appareil à air frais, 1 pc

Kit de suspension, 1 pc

Vis et matériel d'assemblage, 1 pc

Tuyau d’évacuation , 1 pc

Manuel d'installation, 1 pc

ATMO 150H

n'est pas

Homologué

ENERGY STAR.

Note Avertissement/

Note importante Information Information

technique Conseil

pratique

VEUILLEZ LIRE ET CONSERVER CES INSTRUCTIONS

Avant de procéder à l’installation, examinez avec soin la façon dont le système fonctionnera s’il est relié à tout

autre appareil mécanique, notamment une fournaise à air pulsé ou un appareil de traitement d’air dont la pression

statique est plus élevée. Une fois l’installation terminée, la compatibilité des deux appareils doit être conrmée en

mesurant le débit d’air du appareil à air frais (AAF) au moyen de la procédure d’équilibrage du présent manuel. Il

importe de toujours évaluer l’interaction du AAF avec les appareils de chauffage à évacuation

(fournaise à gaz, fournaise à mazout, poêle à bois, etc.)

Les produits sont conçus et fabriqués pour fournir une performance able, mais ils ne sont pas garantis à 100%

sans défaut. Même les produits ont des pannes occasionnelles et cette possibilité devrait être reconnue par

l'utilisateur. Si ces produits sont utilisés dans un système de ventilation qui maintien des fonctions vitales où une

défaillance pourrait entraîner des pertes ou des blessures, l'utilisateur doit fournir une ventilation de secours

adéquate, une ventilation supplémentaire naturelle, un système d'alarme de défaillance ou d'accepter les risques

de pertes ou de blessures.

Votre système de ventilation doit être installé en conformité avec le code du bâtiment local qui est en vigueur, en

l’absence de telles exigences, il est recommandé de vérier auprès des autorités locales ayant juridiction dans

votre région avant d’installer ce produit.

La page charge ...

Fantech 463913 Manuel utilisateur

Marque: Fantech

Modèle: 463913

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Fantech 463913 User manual

Fantech 463913 Manuel utilisateur

Fantech 463913 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents