Fantech FIT 120E Series Manuel utilisateur

Marque: Fantech

Modèle: FIT 120E Series

Catégorie: Climatiseurs split-system

Taper: Manuel utilisateur

FIT 120E Series

Fresh Air Appliance (FAA/ERV)

Appareil d'air frais (AAF/VRE)

Item #: 445657

Rev Date: 2023-04-12

No. d'article #: 445657

Date de révision: 2023-04-12

Your ventilation system should be installed in conformance with the appropriate provincial requirements or, in the absence of

such requirements, with the current edition of the National Building Code, and / or ASHRAE’s “Good Engineering Practices”.

Votre système de ventilation doit être installé conformément aux exigences de la province où vous habitez ou, à défaut de

telles exigences, conformément à l’édition actuelle du Code national du bâtiment du Canada ou aux « méthodes d’ingénierie

appropriées » de l’ASHRAE.

Fantech reserves the right to modify, at any time and without notice, any or all of its products’ features, designs,

components and specifications to maintain their technological leadership position.

Please visit our website www.fantech.net for more detailed technical information.

Fantech se réserve le droit de modifier partiellement ou entièrement, en tout moment et sans préavis, les

caractéristiques, la conception, les composants et les spécifications de ses produits, afin de conserver sa

position de leader de technologie.

S'il vous plaît visitez notre site siteweb www.fantech.net pour des informations techiques plus détaillées.

United States

10048 Industrial Blvd., Lenexa, KS, 66215

Tel.: 800.747.1762 • Fax: 800.487.9915

Canada

50 Kanalflakt Way, Bouctouche, NB, E4S 3M5

Tel.: 800.565.3548 • Fax: 877.747.8116

PARTS IN THE BOX

Energy Recovery Ventilator, 1 pc

Ceiling bracket, 1 pc

Angle brackets, 2 pcs

External Damper Wire harness

(for FIT 120E only), 1 pc

Operation and Installation Manual, 1 pc

PIÈCES DANS LA BOÎTE

Ventilateur récupérateur d'énergie, 1 pc

Support muraux, 1 pc

Équerre d'assemblage, 2 pcs

Faisceau de câbles pour volet d'arrêt

mécanique

externe (FIT 120E seulement), 1 pc

Manuel d'installation, 1 pc

®For FIT®

120E-D-EC

only

Model: FIT 120E

Model: FIT 120E-D

Model: FIT 120E-D-EC

Installation, Operations, and Maintenance Manual

Manuel d’installation, de fonctionnement et de maintenance

Note Warning/

Important

note

Information Technical

information Practical tip

PLEASE READ AND SAVE THESE INSTRUCTIONS

For residential use only

Before installation careful consideration must be given to how this system will operate if connected to

any other piece of mechanical equipment, i.e. a forced air furnace or air handler operating at a higher

static pressure. After installation, the compatibility of the two pieces of equipment must be conrmed by

measuring the airow of the Fresh Air Appliance (FAA) using the balancing procedure found in this manual.

It is always important to assess how the operation of any FAA may interact with vented combustion equipment (i.e.

Gas Furnaces, Oil Furnaces, Wood Stoves, etc.)

Residential FAA ventilation systems are not suitable for pool or spa applications.

Products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100%

free of defects. Even reliable products will experience occasional failures, and this possibility should be recognized

by the user. If these products are used in a life support ventilation system where failure could result in loss or injury,

the user should provide adequate back-up ventilation, supplementary natural ventilation or failure alarm system, or

acknowledge willingness to accept the risk of such loss or injury.

Your ventilation system should be installed in accordance with the local building code that is in effect, in absence

of such requirements, it is recommenced to check with local authorities having jurisdiction in your area prior to

installing this product.

This product earned the ENERGY STAR® by meeting strict energy efficiency guidelines set by Natural Resources Canada

and the US EPA. This product meets ENERGY STAR requirements only when used in Canada.

To ensure quiet operation of the ENERGY STAR certified H/ERV, each product model must be installed using sound attenua-

tion techniques appropriate for the installation.

The way your heat/energy-recovery ventilator is installed can make a significant difference to the electrical energy you use.

To minimize the electricity use of the heat/energy recovery ventilator, a stand-alone fully ducted installation is recommend-

ed. If you choose a simplified installation that operates your forced air system for room-to-room ventilation, an electrically

efficient system that has an electronically commutated (EC) variable speed blower motor will minimize your electrical ener-

gy consumption and operating cost.

Installation of a user-accessible control with your product model will improve comfort and may significantly reduce the prod-

uct model’s energy use.

TABLE OF CONTENTS

DETERMINING YOUR AIRFLOW REQUIREMENT ......................................................4

INSTALLATION EXAMPLES

Fully dedicated system ................................................................ 5

Partially dedicated system .............................................................. 6

Simplified installation ................................................................. 7

EXTERIOR DUCTING INSTALLATION

Weatherhood Location ................................................................. 9

Installing the ducting to the weatherhood ................................................... 9

INTERIOR DUCTING INSTALLATION

General Tips ........................................................................10

Installing duct to FAA................................................................. 10

Supply & Exhaust air grilles location ...................................................... 10

FAA INSTALLATION ........................................................................ 11

Ceiling Mounting .....................................................................12

Wall Mounting.......................................................................13

AIRFLOW ADJUSTMENT & BALANCING

General preparation ................................................................. 14

Balancing steps .................................................................... 15

WALL CONTROLS ......................................................................... 16

WIRING DIAGRAM ......................................................................... 18

TROUBLESHOOTING .........................................................................20

FAA CORE WASHING INSTRUCTIONS .............................................................21

FAA MAINTENANCE CHART ....................................................................22

Room classification Number of rooms CFM (L/s)

CFM Required

Master bedroom x 10 L/s (20 CFM) =

Basement yes or no =

Bedrooms x 5 L/s (10 CFM) =

Living room x 5 L/s (10 CFM) =

Others x 5 L/s (10 CFM) =

Kitchen x 5 L/s (10 CFM) =

Bathroom x 5 L/s (10 CFM) =

Laundry room x 5 L/s (10 CFM) =

Utility room x 5 L/s (10 CFM) =

Total Ventilation Requirements (add last column ) =

if yes add 10 L/s (20 CFM)

if no = 0

1 CFM = 0.47 L/s

1 L/s = 2.13 CFM

Room Count Method

DETERMINING YOUR AIRFLOW REQUIREMENT

ASHRAE method

Ventilation Air requirements

Floor area Bedrooms

1 2 3 4 5

Ft2m2CFM L/s CFM L/s CFM L/s CFM L/s CFM L/s

<500 <47 30 128 38 18 45 21 53 25 60 28

205-1000 47-93 45 21 53 24 60 28 68 31 75 35

1001-1500 94-139 60 28 68 31 75 35 83 38 90 42

1501-2000 140-186 75 35 83 38 90 42 98 45 105 49

2001-2500 187-232 90 42 98 45 105 49 113 52 120 56

2501-3000 233-279 105 49 113 52 120 56 128 59 135 63

3001-3500 280-325 120 56 128 59 135 63 143 66 150 70

3501-4000 326-372 135 63 143 66 150 70 158 73 165 77

4001-4500 373-418 150 70 158 73 165 77 173 80 180 84

4501-5000 419-465 165 77 173 80 180 84 188 87 195 91

* ASHRAE 62.2-2016 Table 4.1, Ventilation and Acceptable Indoor Air Quality in Low-Rise Residential Buildings.

Bathroom: If the FAA is going to provide the required local exhaust ventilation for each bathroom with each a continuous 20 CFM

(10 L/s), this ventilation rate can be considered as part of the whole-building ventilation rate.

Installation examples

FULLY DEDICATED SYSTEM

BEST FOR NEW CONSTRUCTION

Stale air is drawn from key areas of home (bathroom, kitchen, laundry)

Fresh air supplied to main living areas

1. Stale air is drawn from key areas of the home requiring local exhaust

(bathroom, kitchen, laundry room).

2. Fresh air is distributed directly to habitable rooms in the house

(bedrooms, living room)

3. The FAA’s airflow must be balanced after installation using the procedure

found in the section “AIRFLOW BALANCING”

Suggested installation for:

• Hydronic baseboard

• Inoor heating

• Electric baseboard

• Mini split heat pump

Benets: Provides the best fresh

air distribution in the house;

lowest operation cost since the

forced air system is not needed.

Air from inside

* Ductwork layout may

differ depending on model

Stale air to

outside

Fresh air from

outside

Fresh air to

living areas

Outside

FAA/Forced Air System Interlock ducting for Partially Dedicated System

Installation examples (Cont'd)

DIRECT CONNECTION of the FRESH air to living area to the RETURN PLENUM

of the FORCED AIR SYSTEM (Stale air drawn from key areas of home)

1. Forced air system blower must operate when ventilation from FAA is required.

The system should be set to run continuously or interlocked with FAA. See

forced air system electrical connection.

2. Stale air is drawn from key areas of the home (bathroom, kitchen, laundry

room).

3. Fresh air is supplied to the return air plenum of the forced air system.

4. Before operation, the FAA’s airflow must be balanced on site. For this, use the

procedure found in the section “AIRFLOW BALANCING”. During the balancing

procedure, make sure the forced air system blower is running and the FAA is

running at "Normal" speed.

5. In the case of a multi-zone system, please contact Fantech customer

service prior to installing any installation type requiring the use of the

forced air system interlock.

6. The FAA should only be paired with one forced air system. In the case

where there are more than one forced air system please contact Fantech

customer service prior to making a product selection.

Suggested installation for:

• Forced air system (central

furnace or central air

conditioner)

• When ducting fresh air to

living area is not possible or

practical, i.e. expensive or

when the forced air system

will operate year-round

• Recommended install for

units with a built-in outdoor

air motorized damper (such

as the FIT 120E-D & the FIT

120E-D-EC) to avoid drawing

outdoor air directly into the

forced air system when the

unit is not running

Benets: Conditions the fresh

air prior to distributing it

throughout the house

PARTIALLY DEDICATED SYSTEM (BETTER)

Forced Air

System

Air from inside

Air return

1 m (3' 3")

min.

recommended

Cold air

return

* Ductwork layout may

differ depending on model

Stale air to

outside

Fresh air from

outside

Fresh air to

living areas

Outside

For Fresh Air Appliances (FAAs) that do not include an outdoor air motorized damper: If

you are using a partially dedicated or simplied installation, i.e. connecting the FAA supply

air duct to a forced air system's return air duct, the FAA must operate continuously. When

the FAA is turned off, no warm exhaust air will ow through the FAA but the forced air

system's blower will continue to draw in outdoor air through the FAA. When this happens,

the introduction of unconditioned outdoor air to the indoors can increase the load on the

system.

If the FAA is installed so that the homeowner can turn off the FAA, we recommend install-

ing a motorized damper between the FAA's supply air and the forced air system's return

air duct that will close when the FAA is not operating. To install a damper accessory to the

product, locate the auxiliary connector on the side of the electrical box. See Figure 1. Us-

ing the included wire harness, connect the damper accessory to the product.

Figure 1

*Auxiliary connector for external damper wire

harness, damper motor not included.

Forced Air

System

FAA/Forced Air System ducting for Simplified Installation

Installation examples (Cont'd)

DIRECT CONNECTION of both the FAA SUPPLY AIR STREAM and EXHAUST AIR STREAM

to the RETURN PLENUM of the FORCED AIR SYSTEM

SIMPLIFIED INSTALLATION (GOOD) (RETURN/RETURN METHOD)

1. Forced air system blower must operate when ventilation from FAA is required.

The system should be set to run continuously or interlocked with FAA. See

forced air system electrical connection.

2. Stale air is drawn from key areas of the home (bathroom, kitchen, laundry

room).

3. Fresh air is supplied to the return air plenum of the forced air system.

4. Before operation, the FAA’s airflow must be balanced on site. For this, use the

procedure found in the section “AIRFLOW BALANCING”. During the balancing

procedure, make sure the forced air system blower is running and the FAA is

running at "Normal" speed.

5. In the case of a multi-zone system, please contact Fantech customer

service prior to installing any installation type requiring the use of the

forced air system interlock.

6. The FAA should only be paired with one forced air system. In the case

where there are more than one forced air system please contact Fantech

customer service prior to making a product selection.

Suggested installation for:

• When bathroom and kitchen

already have local exhaust

system

• May be suitable for

retrotting

• Recommended install for units

with a built-in outdoor air

motorized damper (such as the

FIT 120E-D & the FIT 120E-D-

EC) to avoid drawing outdoor

air directly into the forced air

system when the unit is not

running

Benets: Least expensive

installation type

For Fresh Air Appliances (FAAs) that do not include an outdoor air motorized damper: If

you are using a partially dedicated or simplied installation, i.e. connecting the FAA supply

air duct to a forced air system's return air duct, the FAA must operate continuously. When

the FAA is turned off, no warm exhaust air will ow through the FAA but the forced air

system's blower will continue to draw in outdoor air through the FAA. When this happens,

the introduction of unconditioned outdoor air to the indoors can increase the load on the

system.

If the FAA is installed so that the homeowner can turn off the FAA, we recommend install-

ing a motorized damper between the FAA's supply air and the forced air system's return

air duct that will close when the FAA is not operating. To install a damper accessory to the

product, locate the auxiliary connector on the side of the electrical box. See Figure 1. Us-

ing the included wire harness, connect the damper accessory to the product.

Figure 1

*Auxiliary connector for external damper wire

harness, damper motor not included.

Air from inside

1 m (3' 3")

min.

recom-

mended

* Ductwork layout may dif-

fer depending on model

Stale air to

outside

Fresh air from

outside

Fresh air to

living areas 1 m (3' 3")

min.

recommended

Air return

EXTERIOR DUCTING INSTALLATION

WEATHERHOOD LOCATION

• Decide where your intake and exhaust hoods will be located.

Locating the Intake Weatherhood

• Should be located upstream (if there are prevailing winds) from the

exhaust outlet.

• At a minimum distance to 900 mm (3') away from dryer vents and

furnace exhaust (medium or high efficiency furnaces), driveways, oil fill

pipes, gas meters, or garbage containers.

• At a minimum height of 460mm (18’’) above the ground, or above the

level of expected snow accumulation.

• Ideally, keep weatherhoods 1m (3') from corners.

• Do not locate in the garage, attic, crawl space, or underneath deck.

Locating the Exhaust Weatherhood

• At least 460mm (18") above ground or above the depth of expected snow accumulation

• Ideally, keep weatherhoods 1m (3') from corners.

• Not near a gas meter, electric meter or a walkway where fog or ice could create a hazard

• Do not locate in a garage, workshop or other unheated space

INSTALLING THE DUCTING TO THE WEATHERHOODS

A well designed and installed ducting system will allow the FAA to operate at its

maximum efficiency. The inner liner of the flexible insulated duct must be secured to the

sleeve of the weatherhood (as close to the outside as possible) and to the appropriate duct

connection on the FAA. The insulation should remain full and not crushed. The outer liner,

which acts as a vapor barrier, must be completely sealed to the outer wall and the FAA

using tape and/or caulking. A good bead of high quality caulking (preferably acoustical

sealant) will seal the inner flexible duct to both the FAA duct connection and the

weatherhood prior to securing them.

To minimize airflow restriction, the flexible insulated duct that connects the two outside

weatherhoods to the FAA should be stretched tightly and be as short as possible.

Twisting or folding the duct will severely restrict airflow.

See “Installation Diagram Examples” for installation examples.

1 Using the duct connection of

the outside hood, outline the

intake & exhaust holes to be

cut. The holes should be slightly

larger than the duct connection

to allow for the thickness of the

insulated flexible duct. Cut a

hole for both the intake and

exhaust hoods.

3 Push the hood into the opening

and then attach the hood to the

outside wall with mounting

screws.

Repeat the installation

procedure for both the supply

and exhaust hoods.

2 Pull the insulated flexible duct

through the opening until it is

well extended and straight.

Slide the duct’s inner vinyl sleeve

over the hood duct connection

and secure. Pull the insulation

over the duct and pull the vapor

barrier over the sleeve. Secure

with appropriate tape or

sealant.

4 Using a caulking gun, seal

around both hoods to prevent

any leaks.

STEPS FOR HOOD INSTALLATION:

36" (1m)

min.

INTAKE

OUTSIDE CORNER INSIDE CORNER

EXHAUST

18" (460mm) min. 18" (460mm) min.

6' (2m)

min.

36” (1m)

min.

Interior ducting installation

• To maximize airflow through the ductwork system, all ducts should be kept short and have as few bends or elbows as possible.

• 45º elbows are preferable to 90º.

• Use “Y“ ducts instead of “T” ducts whenever possible.

• All duct joints must be fastened with screws or duct sealant and wrapped with aluminum foil duct tape to prevent leakage.

• Galvanized ducting from the FAA to the living areas in the house is recommended whenever possible, although flexible ducting

can be used in moderation when necessary.

• The main supply and return line to/from the FAA must have the same diameter as the duct connection or larger.

• Branch lines to the individual rooms may be as small as 100 mm (4’’).

Installing ducting to FAA

Position a 12" (300mm) section of nonmetallic exible duct onto duct collar.

Using (1) cable tie, attach exible ducting with the correct FAA duct collar.

Supply air grilles location

In homes without a forced air system, fresh air should be supplied to all habitable rooms, including bedrooms and living areas. It should be supplied

from high wall or ceiling locations. Grilles that diffuse the air comfortably are recommended. In homes with a forced air system, you may want to

connect the FAA to the system's ductwork (see information below).

Exhaust air grilles location

The stale air exhaust system is used to draw air from the points in the house where the worst air quality problems occur. It is recommended that

return air ducts be installed in the bathroom, kitchen, and laundry room. Additional return air ducts from strategic locations may be installed. The

forced air system's return duct may also be used to exhaust from. In this method, the exhaust air is not ducted back from bathrooms, kitchens, etc

to the FAA with “dedicated lines”.

As per building codes and installation requirements for combustion appliances:

Air return ducts, or openings for air return, should not be placed in enclosed spaces containing combustion

appliances that are subject to spillage.

*Collars may differ depending on the unit.

FAA installation

LOCATION

The FAA must be located in a conditioned space where it will be possible to conveniently service the unit. Typically

the FAA would be located in the mechanical room or an area close to the outside wall where the weatherhoods will

be mounted. If a basement area is not convenient or does not exist, a utility room may be used.

Attic installation must meet the following conditions:

• Attic temperature must be above freezing conditions at all times and for best performance should be 12°C

(54 °F).

• The condensate drain (if included) must be installed so that the condensate drains and is protected from freezing.

• The attic is easily accessible for equipment maintenance and inspection.

Connecting appliances to the FAA is not recommended. These include:

• Clothes dryer

• Range top

• Stovetop fan

• Central vacuum system

• Bathroom exhaust fans unless they are specifically designed for this purpose

These appliances may cause lint, dust or grease to collect in the FAA, damaging the unit.

Connecting any of these types of appliances to the

FAA will void your warranty.

• Have a nearby power supply

(120 volts, 60Hz)

• Choose a location which

allows the possibility

of mounting the unit to

supporting beams.

• To minimize noise, do not

install unit in living area

The unit should be installed in the wall mounted position in re-

gions where the outdoor temperature is 13°F (-25°C) or less for

48 consecutive hours or more while the indoor relative humidity

is at 40% or more.

3 Slide the unit the bracket as shown above.

1 Using the screw with washer mount the mounting bracket through the

rubber insulator. Ensure the bracket is straight.

Mounting

CEILING INSTALLATION

2 Using the screw with washer mount the brackets at the bottom of the

unit.

4 Secure both side of the unit using the same method as step 1.

We recommend placing the duct on the unit at this

stage of the unit's installation.

Mounting

WALL INSTALLATION

1 Using the screw with washer mount the mounting bracket through the

rubber insulator. Ensure the bracket is straight.

3 Slide the unit in the bracket and secure with setting screw.

2 Using the screw with washer mount the brackets at the bottom of the

unit.

Airflow balancing

Balancing must be completed using the Fantech Programmable Touch

Screen Wall Control

ENTERING BALANCING MODE

In the options menu during the initial 5 second countdown

sequence, long press on "ECO" area for 5 seconds to

enter basic balancing mode. The supply and exhaust

fans are adjusted on high speed only and the offsets

are proportionally applied to the medium and low speed

automatically.

STAGE 1

(ADJUST LEVEL OF EXHAUST FAN IN HIGH

SPEED):

• In this step, balance exhaust fan and

measure airow on the exhaust air side

• Pressing on "up" or "down" will adjust the fan

speed in increments of 1%.

• Once the desired exhaust airow is reached,

press on "next" and move on to the next

stage.

STAGE 2

(BALANCE SUPPLY FAN ONLY IN HIGH

SPEED):

• In this step, balance supply fan and measure

airow on the supply air side

• Pressing on "up" or "down" will adjust the fan

speed in increments of 1%.

• Once happy with the outcome, press on

"next" to complete balancing

• The supply and exhaust offset values will be

proportionally applied to low and medium

speed as well.

AUTO MANUAL

OPTIONS

AUTO MANUAL

OPTIONS

AUTO MANUAL

OPTIONS

0 %

ADJUST

AUTO MANUAL

OPTIONS

0 %

BALANCE

WALL CONTROLS

1. Ensure that unit is not plugged when connecting the control

2. Recirculation mode is only available with the Flex100H ES, HERO series and the models with the “R” sufx at the end of the model

number.

The wiring connectors can be removed for easier connection.

* Please see instruction manuals for individual controls for proper wiring and set up of control systems.

CENTRAL CONTROLS

These cannot be used with another central control

*Maintain polarity between control and HRV

(+ → + ; - → -)

ECO SERIES* FEATURES CONNECT TO

ECO-Touch® • Our most complete, yet easy-to-use control system

• Sleek design with backlight touchscreen LCD

• ECO mode selects the best operating mode and speed for the season, minimizing energy use

associated with ventilation

• Set preferred indoor relative humidity range and ventilation mode for day and night conditions

• No battery to replace, all programmed settings are retained during power outages

• Maintenance reminder indicator

• Error code messages reduce troubleshooting time

→

D+

ECO-TouchIAQ • Integrated VOC Sensor

• Our most complete, yet easy-to-use control system

• Sleek design with backlight touchscreen LCD

• ECO mode selects the best operating mode and speed for the season, minimizing energy use

associated with ventilation

• Set preferred indoor relative humidity range and ventilation mode for day and night conditions

• No battery to replace, all programmed settings are retained during power outages

• Maintenance reminder indicator

• Error code messages reduce troubleshooting time

ECO-Feel • ECO mode selects the best operating mode and speed for the season, minimizing energy use

associated with ventilation

• Integrated VOC Sensor

• No battery to replace, all programmed settings are retained during power outages

EDF SERIES FEATURES CONNECTS TO

EDF8 • MODE button provides 3 modes of operations: VENTILATION, RECIRCULATION, and

STANDBY mode.

• User selected fan speed: Reduced, Medium, Normal, and 20 minutes per hour.

• AUTO setting allows the homeowner to deactivate the dehumidistat.

• When the humidity exceeds the desired setpoint, the ventilation system operates at

normal speed.

• Once the desired humidity level is achieved, your ventilation system resumes to its previ-

ous mode of operation.

EDF3 • Press button once for ECONO mode: continuous low or medium speed.

• Press button twice for 20 MIN/H mode: the unit will cycle 20 minutes ON/40 minutes OFF

at intermittent speed and repeat.

• Press button three times for CONT mode: the unit will run continuously in ventilation or

recirculation on HIGH speed.

WALL CONTROLS (CONT'D)

AUXILIARY CONTROL –These controls can be paired with central controls or combined together.

*Maintain polarity between control and FAA

(+ → + ; - → -)

RTS SERIES FEATURES CONNECTS TO

• Wireless timer

• Can only be paired with the ECO-TouchIAQ

• 20/40/60 minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

Connects wireleslly to the

• 20/40/60 minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

• 20- minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

RTS5* • 20/40/60 minute timer with LED light

• Boosts system to high speed with the touch of a button

• Up to 5 can be used in one system

• Use in bathroom, kitchen, laundry room

MDEH SERIES FEATURES CONNECT TO

MDEH1 • Rotary dial Dehumidistat

• Multiple units can be used

• We recommend setting the relative humidity above 80% during the summer

RTS W

D D

RTS4

+ T

– T

RTS2*

Wiring diagram - FIT 120E & FIT 120E-D

Observe polarity on all accessory controls where

applicable.

Wiring diagram - FIT 120E-D-EC

Observe polarity on all accessory controls where

applicable.

WR G Y

Standard Furnace Interlock Wiring

THERMOSTAT

TERMINALS

FURNACE/HEATING

24-VOLT

TERMINAL BLOCK

FOUR

WIRE

TWO WIRE

heating only

TWO

WIRE

COOLING SYSTEM

WR G Y

Alternate Furnace Interlock Wiring

THERMOSTAT

TERMINALS

FURNACE/HEATING

24-VOLT

TERMINAL BLOCK

FOUR

WIRE

TWO WIRE

heating only

TWO

WIRE

COOLING SYSTEM

WIRE JOINT

Wiring diagram (CONT'D)

WIRING DIAGRAM TO

FORCED AIR SYSTEM

FOR A FURNACE

CONNECTION TO

A COOLING SYSTEM:

On some newer furnaces and older

thermostats, energizing the R and

G terminal at the furnace has the

effect of energizing the Y at the

thermostat and thereby turning on

the cooling system. If you identify this

type of thermostat, you must use the

“Alternate Accessory Control Contact”

Standard Accessory Control Contact

Alternative Accessory Control Contact

As per building codes and installation requirements for combustion appliances:

Air return ducts, or openings for air return, should not be placed in enclosed spaces containing combustion

appliances that are subject to spillage.

Troubleshooting

Problem Causes Solutions

Air is too dry Dehumidistat control is set too low Increase the desired level of humidity. Change ventilation mode from

continuous mode to standby.

FAA out of balance Have contractor balance FAA airows

Air is too humid Dehumidistat control is set too high Reduce the desired level of humidity. Combine this with the use of continuous

exchange mode.

Sudden change in temperature Wait until outside temperature stabilizes (winter). Heating will also improve

situation.

Storing too much wood for heating Store a majority of your wood outside. Even dried, a cord of wood contains

more than 20 gallons of water.

Dryer vent exhaust is inside home Make sure the dryer vent is exhausting outside.

Poor air circulation near windows Open curtains or blinds.

FAA out of balance Have contractor balance FAA airows

Well sealed basement door is closed Open the door or install a grill on the door.

Persistent condensation

on window

Improper adjustment of dehumidistat control Reduce the desired level of humidity. Combine this step with use of continuous

exchange mode.

FAA out of balance Have contractor balance FAA

Poor air circulation near windows Open curtains or blinds.

Poor Airows 1/4" (6mm) mesh on the outside hoods is plugged Clean exterior hoods or vents

Filters plugged Remove and clean lter

Core obstructed Remove and clean core

Indoor grilles closed or blocked Check and open grilles

Inadequate power supply at site Have electrician check supply voltage

Ductwork is restricting airow Check duct installation

Improper speed control setting Increase the speed of the FAA (i.e. change unit control from REDUCED to NORMAL

speed)

FAA airow improperly balanced Have contractor balance FAA airows

Ducting has fallen down or been disconnected from FAA Have contractor reconnect ducting

Supply air feels cold Poor location of supply grilles, the airow may irritate

the occupant

Locate the grilles high on the walls or under the baseboards, install ceiling

mounted diffuser or grilles so as not to directly spill the supply air on the

occupant (eg. Over a sofa)

Turn down the FAA supply speed. A small duct heater (1kw) could be used to

temper the supply air

Placement of furniture or closed doors is restricting the movement of air in

the home

Outdoor temperature extremely cold If supply air is ducted into furnace return, the furnace fan may need to run

continuously to distribute ventilation air comfortably

FAA and/or Ducts frosting up FAA airows are improperly balanced Have HVAC contractor balance the FAA airows

Malfunction of the FAA defrost system Note: minimal frost build-up is expected on cores before unit initiates defrost

cycle functions

Condensation or Ice Build Up in

Insulated Duct to the Outside

Incomplete vapor barrier around insulated duct Tape and seal all joints

A hole or tear in outer duct covering Tape any holes or tears made in the outer duct covering

Ensure that the vapor barrier is completely sealed.

LED is ashing Everything is in good operation

No power is being transmitted to the Control Board Make sure unit is plugged in.

Transformer may need replacing

Note: It is best to get the unit checked by a certied HVAC Contractor/Technician.

Filters and FAA core washing instructions

For proper maintenance of your energy recovery core please follow these instructions

1 To remove the door, loosen both latches on

the bottom of the unit.

2 Rotate the metal plate holding the FAA core

in place.

3 Remove both lters. Wash lters in warm

soapy water then rinse and let dry.

4 Remove the core from the unit.

5 With one of your core's air inlets facing

down, place it in a large sink, bathtub, or

shower.

6 Pour clean tap water through the face of the

core facing upwards until it runs clear.

Ensure the entire surface is rinsed.

7 Rotate the core so that its other air inlet is

facing down and repeat step 5.

8 With plates still oriented vertically allow the

core to dry, normally 2-3 hours.

9 Replace the lter.

10 Slide back the core into the system making

sure that the arrow points to the motors.

Rotate the metal plate holding the FAA Core

in place.

11 Reattach the door.

12 Close the door, and secure both latches.

La page charge ...

Fantech FIT 120E Series Manuel utilisateur

Marque: Fantech

Modèle: FIT 120E Series

Catégorie: Climatiseurs split-system

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Fantech FIT 120E Series User manual

Fantech FIT 120E Series Manuel utilisateur

Fantech FIT 120E Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents