CHAUVET DJ Intimidator Wave 360 IRC Guide de référence

Catégorie
Stroboscopes
Taper
Guide de référence
Quick Reference Guide
Intimidator Wave 360 IRC QRG EN
2
About This Guide
The Intimidator Wave 360 IRC Quick Reference Guide (QRG) has basic product
information such as mounting, menu options, and DMX values. For more
information, download the User Manual from the Chauvet
website:
http://www.chauvetlighting.com.
Disclaimer
The information and specifications contained in this QRG are subject to change
without notice.
Safety Notes
The following Safety Notes include important information about installation, use,
and maintenance.
Always connect the product to a grounded circuit.
Make sure the power cord is not crimped or damaged.
Always disconnect the product from the power source before cleaning it or
replacing the fuse.
Never disconnect the product from the power source by pulling or tugging on
the cord.
If mounting the product overhead, make sure there is adequate support for the
product’s weight and always secure the product using a safety cable.
Make sure there are no flammable materials close to the product when it is
operating.
Avoid direct eye exposure to the light source while the product is on.
Do not touch the product’s housing when the product is operating because the
housing can be very hot.
The product is not intended for permanent installation.
The product is for indoor use only. It is rated at IP20.
Do not expose the product to rain or moisture.
Always connect the product to a power source that is within the voltage range
stated on the label or rear panel of the product.
Never connect the product to a dimmer or rheostat.
Make sure to replace the fuse with another of the same type and rating.
Always install the product in a location with adequate ventilation.
Always leave at least 20 in (50 cm) between the product and adjacent surfaces.
Be sure that no ventilation slots on the product’s housing are blocked.
Do not operate the product at an ambient temperature higher than
104 °F (40 °C).
Never carry the product by the power cord or any moving part.
Always use the hanging/mounting bracket to lift the product.
If there is a serious operating problem, stop using the product immediately.
Never try to repair the product. Repairs carried out by untrained people can
lead to damage or malfunction.
To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power via breaker or by
unplugging it.
Contact
From outside the U.S., UK, Ireland, Mexico, or Benelux, contact the
distributor of record to request support or return a product.
From inside the U.S., UK, Ireland, Mexico, or Benelux, use the information in
Contact Us at the end of this QRG.
What Is
Included
Intimidator Wave 360 IRC
Hanging bracket with mounting
hardware
Power Cord
Warranty card
Quick Reference Guide
Intimidator Wave 360 IRC QRG EN
3
To Begin
Carefully unpack the Intimidator Wave 360 IRC and check that all the parts are in
the package, and are in good condition.
If the box, or any of the contents, appear damaged from shipping, or
show signs of
mishandling, save all packaging and file a claim with the carrier immediately, do
not notify Chauvet. Failure to report damage to the carrier immediately, or failure
to have all packaging available for inspection, could invalidate your claim.
For other issues, such as missing components or parts, damage not related to
shipping, or concealed damage, file a claim with Chauvet within 7 days of
delivery. For information on contacting Chauvet, see Contact Us at the en
d of this
QRG.
Description
The Intimidator Wave 360 IRC is a moving light array with 4 independently
controlled moving heads on a continuously rotating base
emitting sharp, powerful,
color-changeable beams. Master/Slave mode makes it easy to generate coor
dinated
light shows. It operates in Standalone, Sound, and DMX modes.
Works with the
(optional) IRC-6 remote for convenient, wireless control up to 15 feet away.
Overview
Display
Head 1
Head 2
Head 3
Control Buttons
Front View
Back View
Power In
Power Out
Fuse
Holder
DMX In
DMX Out
Cooling
Fan
Safety
Loop
Intimidator Wave 360 IRC QRG EN
4
AC Power
Intimidator Wave 360 IRC has an auto-ranging power supply that can work with
an input voltage range of 100240 VAC, 50/60 Hz.
To eliminate wear and improve its lifespan, during periods of non-use
completely disconnect from power via breaker or by unplugging it.
Power Linking
Power linking is accomplished when products are daisy chained together through
their Power In and Power Out sockets, so that many products can be powered from
one outlet.
For the maximum number of Intimidator Wave 360 IRC product
s that can be
power linked at 120 V or at 240 V, see
the User Manual or the label on the
product. The User Manual is available at the Chauvet website
http://www.chauvetlighting.com.
Fuse Replacement
1. Disconnect the product from power.
2. With a flat-head screwdriver, unscrew the fuse holder cap from
the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect power.
Disconnect the product from power before replacing the fuse.
Mounting
Before mounting this product, read the Safety Notes. Use one or two mounting points
and one safety cable per product. Make sure the mounting clamps are capable of
supporting the weight of the product. For the Chauvet line o
f mounting clamps, go to
the Chauvet website at https://www.chauvetdj.com/products/category/accessories/.
Mounting Diagram
Hanging/Mounting
Bracket
Mounting Clamp
Rubber
Feet (x4)
for Floor
Mounting
Safety
Cable
Intimidator Wave 360 IRC QRG EN
5
When using only one mounting clamp, be sure to use a clamp with a captive
bolt to prevent accidental loosening.
Control Panel
Description
Button
Function
<MENU>
Exits from the current menu or function
<UP>
Navigates upwards through the menu list or increases the
numeric value when in a function
<DOWN>
Navigates downwards through the menu list or decreases the
numeric value when in a function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value into the selected function
Menu Map
Main Level
Programming Levels
Description
Address
001512
Sets DMX starting address
Run Mode
DMX
17CH
Sets DMX personality
33CH
Auto
Auto01Auto16
Sets an auto program
Sound
Slave
S-1–S-4
Sets a Slave mode
IR
Sets Infrared mode
Setup
Mast Set
M-1–M-4
Sets a Master mode of M-1, M-2 or M-4
Pan Reverse
ON
Sets reverse pan operation
OFF
Tilt Reverse
ON
Sets reverse tilt operation
OFF
Pan Angle
540
Sets pan angle range
360
180
Tilt Angle
90
Sets tilt angle range
180
270
Display
ON
Sets display blackout
OFF
Screen Reverse
ON
Sets screen orientation
OFF
Dimmer Curve
Linear
Sets the dimmer curve mode
SCurve
I Square
Square
Dimmer Speed
Smooth
Sets the dimmer speed
Fast
Sensitivity
1–100
Sets sound sensitivity
Intimidator Wave 360 IRC QRG EN
6
Reset
Resets all motor defaults
Factory Reset
Resets to factory defaults
Main Level
Programming Levels
Description
System Info
Ver XX
Displays software version
Running Mode XXXXX
Displays current operating mode
DMX Address XXX
Displays current DMX address
IRC-6 (Infrared
Remote Control)
The Intimidator Wave 360 IRC is compatible with the IRC-6 from Chauvet.
The following IRC-6 buttons are used with the Intimidator Wave 360 IRC :
<BLACKOUT>, <A>, <UV>, <W> - Turns LED on/off
<AUTO> , <0> thru <9> - Selects Auto program mode (1-16)
<SOUND> - Selects Sound mode
<STROBE> - Strobing (020 Hz)
<SPEED> - Auto program speed
<SENSITIVITY> - Sets sound sensitivity
<%> - Dimmer
<FADE> - Press once for Fade level, twice for Snap level
<+> and <-> - increase and decrease
<MANUAL> - Sets white color level
<R> - Sets red color level
<G> - Sets green color level
<B> - Sets blue color level
DMX Linking
The Intimidator Wave 360 IRC works with a DMX controller. Information about
configuring the Intimidator Wave 360 IRC
for DMX operation is in the User
Manual, which is available from the Chauvet website
http://www.chauvetlighting.com. Information about DMX is in the Chauvet
DMX
Primer, which is available from the Chauvet web
site
https://www.chauvetdj.com/downloads/.
Starting Address
To ensure full access to all channels in each DMX mode, the highest recommended
DMX address for this product is 480.
Master/Slave
Connection
The Intimidator Wave 360 IRC works in Master/Slave mode. Information about
configuring this product for Master/Slave operation is in its User Manual, which is
available from the Chauvet website.
DMX Assignments
33CH
Channel
Function
Value
Percent/Setting
1
Pan
000ó255
Pan 0–540°
2
Pan 16-bit
000ó255
Pan 16-bit
3
Pan Speed
000ó255
Pan Speed (decreasing speed)
4
Continuous Pan
Rotating
000
No function
001ó127
Continous pan rotating with increasing speed
128ó255
Continous pan rotating with decreasing speed
5
Head 1 Tilt
000ó255
0–270°
6
Head 2 Tilt
000ó255
0–270°
Intimidator Wave 360 IRC QRG EN
7
DMX Assignments (Cont.)
33CH
Channel
Function
Value
Percent/Setting
7
Head 3 Tilt
000
ó
255
0–270°
8
Head 4 Tilt
000
ó
255
0–270°
9
Built-In Auto Tilt
000ó047
No function
048ó055
Built-In Auto 1
056ó063
Built-In Auto 2
064ó071
Built-In Auto 3
072
ó
079
Built-In Auto 4
080
ó
087
Built-In Auto 5
088ó095
Built-In Auto 6
096
ó
103
Built-In Auto 7
104
ó
111
Built-In Auto 8
112
ó
119
Built-In Auto 9
120ó127
Built-In Auto 10
128
ó
135
Built-In Auto 11
136
ó
143
Built-In Auto 12
144
ó
151
Built-In Auto 13
152
ó
159
Built-In Auto 14
160
ó
167
Built-In Auto 15
168
ó
175
Built-In Auto 16
176
ó
183
Built-In Auto 17
184ó191
Built-In Auto 18
192
ó
199
Built-In Auto 19
200
ó
207
Built-In Auto 20
208
ó
215
Built-In Auto 21
216
ó
223
Built-In Auto 22
224
ó
231
Built-In Auto 23
232
ó
239
Built-In Auto 24
240
ó
247
Built-In Auto 25 (Built-In Auto 1–24)
248
ó
255
Built-In Sound Control mode
10
Tilt Built-in Speed
000
ó
255
Fast to slow
Intimidator Wave 360 IRC QRG EN
8
DMX Assignments (Cont.)
33CH
Channel
Function
Value
Percent/Setting
11
Head 1 Red
Dimmer
000ó255
0–100%
12
Head 1 Green
Dimmer
000ó255
0–100%
13
Head 1 Blue
Dimmer
000ó255
0–100%
14
Head 1 White
Dimmer
000ó055
0–100%
15
Head 2 Red
Dimmer
000ó255
0–100%
16
Head 2 Green
Dimmer
000ó255
0–100%
17
Head 2 Blue
Dimmer
000ó255
0–100%
18
Head 2 White
Dimmer
000ó255
0–100%
19
Head 3 Red
Dimmer
000ó255
0–100%
20
Head 3 Green
Dimmer
000ó255
0–100%
21
Head 3 Blue
Dimmer
000ó255
0–100%
22
Head 3 White
Dimmer
000ó255
0–100%
23
Head 4 Red
Dimmer
000ó255
0–100%
24
Head 4 Green
Dimmer
000ó255
0–100%
25
Head 4 Blue
Dimmer
000ó255
0–100%
26
Head 4 White
Dimmer
000ó255
0–100%
Intimidator Wave 360 IRC QRG EN
9
DMX Assignments (Cont.)
33CH
Channel
Function
Value
Percent/Setting
27 Colors
000ó007
No function
008ó015
Color 1
016ó023
Color 2
024ó031
Color 3
032ó039
Color 4
040ó047
Color 5
048ó055
Color 6
056ó063
Color 7
064ó071
Color 8
072ó079
Color 9
080ó087
Color 10
088ó095
Color 11
096ó103
Color 12
104ó111
Color 13
112ó119
Color 14
120ó127
Color 15
128ó179
No Function
180ó201
Fade rainbow clockwise (speed fast to slow)
202ó207
Stop
208ó229
Fade rainbow counter-clockwise
(speed fast to slow)
230ó234
No function
235ó249
Snap change (speed fast to slow)
250ó255
Sound color
Intimidator Wave 360 IRC QRG EN
10
DMX Assignments (Cont.)
33CH
Channel
Function
Value
Percent/Setting
28 Heads On/Off
000ó007
●●●●
008ó015
○●●●
016ó023
○○●●
024ó031
○○○●
032ó039
○○○○
040ó047
●○○○
048ó055
●●○○
056ó063
●●●○
064ó071
●●●●
072ó079
○○○○
080ó087
●○○○
088ó095
○●○○
096ó103
○○●○
104ó111
○○○●
112ó119
○○○○
120ó127
●●○○
128ó135
○●●○
136ó143
○○●●
144ó151
●○○●
152ó159
○○○○
160ó167
○●●●
168ó175
○●●
176ó183
●●○●
184ó191
●●●○
192ó199
○○○○
200ó207
●●●●
208ó215
●●●●
216ó223
●●●●
224ó231
●●●●
232ó239
●●●●
240ó247
●●●●
248ó255
●●●●
Intimidator Wave 360 IRC QRG EN
11
DMX Assignments (Cont.)
33CH
Channel
Function
Value
Percent/Setting
29 Auto Programs
000ó015
No function
016ó020
Program 1
021ó025
Program 2
026ó030
Program 3
031ó035
Program 4
036ó040
Program 5
041ó045
Program 6
046ó050
Program 7
051ó055
Program 8
056ó060
Program 9
061ó065
Program 10
066ó070
Program 11
071ó075
Program 12
076ó080
Program 13
081ó085
Program 14
086ó090
Program 15
091ó095
Program 16
096ó100
Program 17
101ó105
Program 18
106ó110
Program 19
111ó115
Program 20
116ó120
Program 21
121ó125
Program 22
126ó130
Program 23
131ó135
Program 24 (built-in for all)
136ó140
Program 25
141ó145
Program 26
146ó150
Program 27
151ó155
Program 28
156ó160
Program 29
161ó165
Program 30
166ó170
Program 31
171ó175
Program 32
176ó180
Program 33
181ó185
Program 34
186ó190
Program 35
191ó195
Program 36
Intimidator Wave 360 IRC QRG EN
12
DMX Assignments (Cont.)
33CH
Channel
Function
Value
Percent/Setting
29
Auto Programs
(Cont.)
196ó200
Program 37
201ó205
Program 38
206ó210
Program 39
211ó215
Program 40
216ó220
Program 41
221ó225
Program 42
226ó230
Program 43
231ó235
Program 44
236ó240
Program 45
241ó245
Program 46
246ó250
Program 47
251ó255
Program 48 (built-in for all)
30
Program Speed
000ó255
Slow to fast
31
Dimmer All Heads
000ó255
0–100%
32 Shutter Programs
000ó019
Off
020ó024
On
025ó064
Shutter 1 even on/even off (fast to slow)
065ó069
On
070ó084
Shutter 2 fast on/slow off (fast to slow)
085ó089
On
090ó104
Shutter 3 slow on/fast off (fast to slow)
105ó109
On
110ó124
Shutter 4 random shutter (fast to slow)
125ó129
On
130ó144
Shutter 5 random shutter fast on/slow off
(fast to slow)
145ó149
On
150ó164
Shutter 6 random shutter slow on/fast off
(fast to slow)
165ó169
On
170ó184
Shutter 7 pulse shutter (fast to slow)
185ó189
On
190ó204
Shutter 8 random pulse shutter (fast to slow)
205ó209
On
210ó224
Shutter 9 on and off gradually (fast to slow)
225ó229
On
230ó244
Shutter 10 pulse shutter (fast to slow)
245ó255
On
Intimidator Wave 360 IRC QRG EN
13
DMX Assignments (Cont.)
33CH
Channel
Function
Value
Percent/Setting
33
Settings
(Set these values
before setting other
DMX channels.
There is a 10 sec
delay before the
settings take effect)
000ó009
No function
010ó014
Move-in-black
015ó019
Cancel move-in-black
020ó024
Independent macros cancels macro product
combinations below
025ó029
Macros used when linking 2 heads: This is the
value for first head
030ó034
Macros used when linking 2 heads together:
This is the value for second head
035ó039
Macros used when linking 4 heads together:
This is the value for first head
040ó044
Macros used when linking 4 heads together:
This is the value for second head
045ó049
Macros used when linking 4 heads together:
This is the value for third head
050ó054
Macros used when linking 4 heads together:
This is the value for fourth head
055ó059
Pan reset
060ó064
Tilt reset
065ó069
Reserved for future use
070ó074
Reset all
075ó079
Reserved for future use
080ó084
Pan/ tilt reverse
085ó089
Pan reverse
090ó094
Tilt Reverse
095ó099
Cancel reverse pan
100ó104
Cancel reverse tilt
105ó109
Cancel reverse pan/tilt
110ó114
Reserved for future use
115ó119
Controls all heads with head 1 channels
120ó124
Cancels control of all heads with
head 1 channels
125ó129
Reserved for future use
130ó134
Reserved for future use
135ó139
Reserved for future use
140ó144
Reserved for future use
145ó255
No function
Intimidator Wave 360 IRC QRG EN
14
DMX Assignments (Cont.)
17CH
Channel
Function
Value
Percent/Setting
1
Pan
000ó255
Pan 0–540°
2
Pan 16-bit
000ó255
Pan 16-bit
3
Pan Speed
000ó255
Pan speed (decreasing speed)
4
Continuous Pan
Rotating
000
No function
001ó127
Continous pan rotating with increasing speed
128ó255
Continous pan rotating with decreasing speed
5
Head 1 Tilt
000ó255
0–270°
6
Head 2 Tilt
000ó255
0–270°
7
Head 3 Tilt
000ó255
0–270°
8
Head 4 Tilt
000ó255
0–270°
9
Built-In Auto Tilt
000
ó
047
No function
048
ó
055
Built-In Auto 1
056
ó
063
Built-In Auto 2
064
ó
071
Built-In Auto 3
072
ó
079
Built-In Auto 4
080
ó
087
Built-In Auto 5
088
ó
095
Built-In Auto 6
096
ó
103
Built-In Auto 7
104
ó
111
Built-In Auto 8
112
ó
119
Built-In Auto 9
120
ó
127
Built-In Auto 10
128
ó
135
Built-In Auto 11
136
ó
143
Built-In Auto 12
144
ó
151
Built-In Auto 13
152
ó
159
Built-In Auto 14
160
ó
167
Built-In Auto 15
168
ó
175
Built-In Auto 16
176
ó
183
Built-In Auto 17
184
ó
191
Built-In Auto 18
192
ó
199
Built-In Auto 19
200
ó
207
Built-In Auto 20
Intimidator Wave 360 IRC QRG EN
15
DMX Assignments (Cont.)
17CH
(cont.)
Channel
Function
Value
Percent/Setting
9
(cont.)
Built-In Auto Tilt
(cont.)
208
ó
215
Built-In Auto 21
216
ó
223
Built-In Auto 22
224
ó
231
Built-In Auto 23
232
ó
239
Built-In Auto 24
240
ó
247
Built-In Auto 25 (Built-In Auto 1-24)
248
ó
255
Built-In Sound Control Mode
10
Tilt Built-in Speed
000
ó
255
Fast to slow
11 Colors
000ó007
No function
008ó015
Color 1
016ó023
Color 2
024ó031
Color 3
032ó039
Color 4
040ó047
Color 5
048ó055
Color 6
056ó063
Color 7
064ó071
Color 8
072ó079
Color 9
080ó087
Color 10
088ó095
Color 11
096ó103
Color 12
104ó111
Color 13
112ó119
Color 14
120ó127
Color 15
128ó179
No function
180ó201
Fade rainbow clockwise (speed fast to slow)
202ó207
Stop
208ó229
Fade rainbow counter-clockwise
(speed fast to slow)
230ó234
No function
235ó249
Snap change (speed fast to slow)
250ó255
Sound color
Intimidator Wave 360 IRC QRG EN
16
DMX Assignments (Cont.)
17CH
Channel
Function
Value
Percent/Setting
12 Heads On/Off
000ó007
●●●●
008ó015
○●●●
016ó023
○○●●
024ó031
○○○
032ó039
○○○○
040ó047
●○○○
048ó055
●●○○
056ó063
●●●○
064ó071
●●●●
072ó079
○○○○
080ó087
●○○○
088ó095
○●○○
096ó103
○○●○
104ó111
○○○●
112ó119
○○○○
120ó127
●●○○
128ó135
○●●○
136ó143
○○●●
144ó151
●○○●
152ó159
○○○○
160ó167
○●●●
168ó175
●○●●
176ó183
●●○●
184ó191
●●●○
192ó199
○○○○
200ó207
●●●●
208ó215
●●●●
216ó223
●●●●
224ó231
●●●●
232ó239
●●●●
240ó247
●●●●
248ó255
●●●●
Intimidator Wave 360 IRC QRG EN
17
DMX Assignments (Cont.)
17CH
Channel
Function
Value
Percent/Setting
13 Auto Programs
000ó015
No function
016ó020
Program 1
021ó025
Program 2
026ó030
Program 3
031ó035
Program 4
036ó040
Program 5
041ó045
Program 6
046ó050
Program 7
051ó055
Program 8
056ó060
Program 9
061ó065
Program 10
066ó070
Program 11
071ó075
Program 12
076ó080
Program 13
081ó085
Program 14
086ó090
Program 15
091ó095
Program 16
096ó100
Program 17
101ó105
Program 18
106ó110
Program 19
111ó115
Program 20
116ó120
Program 21
121ó125
Program 22
126ó130
Program 23
131ó135
Program 24 (built-in for all)
136ó140
Program 25
141ó145
Program 26
146ó150
Program 27
151ó155
Program 28
156ó160
Program 29
161ó165
Program 30
166ó170
Program 31
171ó175
Program 32
Intimidator Wave 360 IRC QRG EN
18
DMX Assignments (Cont.)
17CH
Channel
Function
Value
Percent/Setting
13
(cont.)
Auto Programs
(Cont.)
176ó180
Program 33
181ó185
Program 34
186ó190
Program 35
191ó195
Program 36
196ó200
Program 37
201ó205
Program 38
206ó210
Program 39
211ó215
Program 40
216ó220
Program 41
221ó225
Program 42
226ó230
Program 43
231ó235
Program 44
236ó240
Program 45
241ó245
Program 46
246ó250
Program 47
251ó255
Program 48 (built-in for all)
14
Program Speed
000ó255
Slow to fast
15
Dimmer All Heads
000ó255
0–100%
Intimidator Wave 360 IRC QRG EN
19
DMX Assignments (Cont.)
17CH
Channel
Function
Value
Percent/Setting
16 Shutter Programs
000ó019
Off
020ó024
On
025ó064
Shutter 1 even on/even off (fast to slow)
065ó069
On
070ó084
Shutter 2 fast on/slow off (fast to slow)
085ó089
On
090ó104
Shutter 3 slow on/fast off (fast to slow)
105ó109
On
110ó124
Shutter 4 random shutter (fast to slow)
125ó129
On
130ó144
Shutter 5 random shutter fast on/slow off
(fast to slow)
145ó149
On
150ó164
Shutter 6 random shutter slow on/fast off
(fast to slow)
165ó169
On
170ó184
Shutter 7 pulse shutter (fast to slow)
185ó189
On
190ó204
Shutter 8 random pulse shutter (fast to slow)
205ó209
On
210ó224
Shutter 9 on and off gradually (fast to slow)
225ó229
On
230ó244
Shutter 10 pulse shutter (fast to slow)
245ó255
On
Intimidator Wave 360 IRC QRG EN
20
DMX Assignments (Cont.)
17CH
Channel
Function
Value
Percent/Setting
17
Settings
(Set these values
before setting other
DMX channels.
There is a 10 sec
delay before the
settings take effect)
000ó009
No function
010ó014
Move-in-black
015ó019
Cancel move-in-black
020ó024
Independent macros cancels macro product
combinations below
025ó029
Macros used when linking 2 heads: This is the
value for first head
030ó034
Macros used when linking 2 heads together:
This is the value for second head
035ó039
Macros used when linking 4 heads together:
This is the value for first head
040ó044
Macros used when linking 4 heads together:
This is the value for second head
045ó049
Macros used when linking 4 heads together:
This is the value for third head
050ó054
Macros used when linking 4 heads together:
This is the value for fourth head
055ó059
Pan reset
060ó064
Tilt reset
065ó069
Reserved for future use
070ó074
Reset all
075ó079
Reserved for future use
080ó084
Pan/ tilt reverse
085ó089
Pan reverse
090ó094
Tilt reverse
095ó099
Cancel reverse pan
100ó104
Cancel reverse tilt
105ó109
Cancel reverse pan/tilt
110ó114
Reserved for future use
115ó119
Controls all heads with head 1 channels
120ó124
Cancels control of all heads with
head 1 channels
125ó129
Reserved for future use
130ó134
Reserved for future use
135ó139
Reserved for future use
140ó144
Reserved for future use
145ó255
No function
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

CHAUVET DJ Intimidator Wave 360 IRC Guide de référence

Catégorie
Stroboscopes
Taper
Guide de référence