Thermador VCIB54JP Guide d'installation

INSTALLATION MANUAL

For THERMADOR PROFESSIONAL

®

Custom Insert

MANUEL D'INSTALLATION

Pour hottes encastrées sur mesure PROFESSIONAL

MC

de THERMADOR

MANUAL DE INSTALACIÓN

Para campanas empotradas a medida PROFESSIONAL

®

de THERMADOR

Models/

Modèles/

Modelos:

VCIN36JP

VCIN48JP

VCIN54JP

VCIB36JP

VCIB48JP

VCIB54JP

Table of Contents

This THERMADOR

®

appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Advance Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Ductwork Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Choosing the Correct Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Blower Motor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Remote Installation (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Preparing the Ceiling Cutout and Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Custom Insert Installation with Hood Trims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Custom Insert Installation with Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installing Filters, Filter Spacers, & Grease Trays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Before Calling Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Product Data Rating Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Installer Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Service, Parts & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . back page

Safety Definitions

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or tips.

WARNING

This indicates that death or serious injuries may occur as

a result of non-observance of this warning.

CAUTION

This indicates that minor or moderate injuries may occur

as a result of non-observance of this warning.

English 1

Safety

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT: Save these instructions for the local

electrical inspector’s use.

INSTALLER: Please leave these instructions with this unit

for the owner. Show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

OWNER: Please retain these instructions for future

reference.

Electric Safety

Grounding Instructions:

This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric current.

Be sure your appliance is properly installed and grounded

by a qualified technician. Installation, electrical connections

and grounding must comply with all applicable codes.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

To reduce the risk of fire or electric shock, do not use this

appliance with any solid-state speed control devices.

WARNING

If the information in this manual is not followed exactly, fire

or shock may result causing property damage or personal

injury.

WARNING

Turn off power circuit at service panel and lock out panel

before wiring this appliance. Requirement: 120 VAC, 60

Hz 15 A. Allow the appliance to cool after the power has

been turned off before servicing the appliance.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed on the back page.

• Before servicing or cleaning unit, switch power off at

service panel and lock the service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

WARNING

Do not repair or replace any part of the appliance unless

specifically recommended in the manuals. Improper

installation, service or maintenance can cause injury or

property damage. Refer to this manual for guidance. All

other servicing should be done by a qualified technician.

WARNING

IMPROPER GROUNDING CAN RESULT IN A

RISK OF ELECTRIC SHOCK.

Consult a qualified electrician if the grounding

instructions are not completely understood, or if

doubt exists as to whether the appliance is

properly grounded. If the power cord is too short,

have a qualified electrician install an outlet near

the appliance.

DO NOT USE AN EXTENSION

CORD.

WARNING

ELECTRICAL SHOCK HAZARD

• DO NOT remove connections.

• DO NOT use an extension cord.

• Improper grounding can result in a risk of

electric shock.

• Failure to follow these instructions can result

in death, fire, or electrical shock.

English 2

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Safety Codes and Standards

This appliance complies with one or more of the following

Standards:

• UL 507, The Standard for the Safety of Electric Fans

• CSA C22.2 No. 113, Fans and Ventilators

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Appliance Handling Safety

Related Equipment Safety

Never modify or alter the construction of the appliance. For

example, do not remove panels, wire covers or brackets/

screws.

When cutting or drilling into wall or ceiling, be careful not to

damage electrical wiring and other hidden utilities.

Use a quali¿ed and trained installer.

Remove all tape and packaging before using the appliance.

Destroy the packaging after install. Never allow children to

play with packaging material.

Ventilation Safety

CAUTION

Unit is heavy and requires at least two people

or proper equipment to move and install.

Hidden surfaces may have sharp edges. Use

caution when handling the appliance. Failure

to do so may result in property damage or

personal injury.

WARNING

State of California Proposition 65 Warnings:

This product contains chemicals known to the State of

California to cause cancer, birth defects or other

reproductive harm.

CAUTION

For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors. To reduce

the risk of fire, use only metal ductwork.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable

codes and standards, including fire-rated

construction.

• Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent back drafting. Follow

the heating equipment manufacturer's guideline and

safety standards such as those published by the

National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local

code authorities.

• USE ONLY METAL DUCTWORK.

• Ducted fans must always be vented to the outdoors.

DO NOT vent exhaust air into spaces within walls,

ceilings, attics, crawl spaces or garages.

• When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

English 3

Advance Planning

Before You Begin

Parts Included

1 – 1000 CFM integral blower

(VCIBxxJP models only)

1 – Metal transition with backdraft

damper

2, 3, or 4 – Stainless steel baffle filters

(depending on model size)

2 – Filter spacers

2 or 3 – Grease trays (depending on

model size)

1 – Liner (VCIBxxJP models only)

4 – Side trims (VCINxxJP models only)

2 or 4 – Halogen lights, installed

(depending on size)

1 – Remote blower adaptor

1 – Fastener assortment

Literature packet

CAUTION

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being turned

ON accidentally.

Tools and Parts Needed

Blower motor (VCINxxJP models only)

Ductwork as necessary (style varies, see Table 3)

Additional sheet metal screws (as necessary for ductwork

installation)

1'' (25.4 mm) Strain relief

Aluminum tape (DO NOT use duct tape)

1/2'' (13 mm) Conduit if required (follow local codes)

Framing material (as necessary for framework)

Circular saw or jigsaw

Tape measure

Phillips head screwdriver

Protective work gloves

Optional accessories available for separate purchase.

Refer to www.thermador.com for more details.

LINER236 – 36'' Custom Hood Liner

LINER248 – 48'' Custom Hood Liner

LINER254 – 54'' Custom Hood Liner

TRIM236 – 36'' Custom Hood Trims

TRIM248 – 48'' Custom Hood Trims

TRIM254 – 54'' Custom Hood Trims

VCI2REMKS – Remote Control Panel

EXTNCB25 – 25 ft. Blower Connection Cable

PA36JBS, PA48JBS – Backsplash

English 4

General Information

This manual provides the proper installation instructions for two styles of THERMADOR PROFESSIONAL

®

custom insert

hoods:

Overall Dimensions

VCINxxJP — This model series features brushed stainless-steel filters, halogen lights, and side trims.

VCIBxxJP — This model series features brushed stainless-steel filters, halogen lights, optional hood liner, and an integral

blower.

NOTE: Installation without option hood liner requires Accessory Custom Insert Hood Trims, TRIM2xx.

NOTE: Transition is centered.

36'' (914)

without liner

48'' (1,219)

without liner

54'' (1,372)

without liner

36'' (914)

with liner

48'' (1,219)

with liner

54'' (1,372)

with liner

A 32Ǫ'' (822) 44Ǫ'' (1,127) 50'' (1,280) 32Ǫ'' (822) 44Ǫ'' (1,127) 50Ǫ'' (1,280)

B

33¾'' (856) 45¾'' (1,162) 51¾'' (1,315)

39

3

/

16

'' (995) 51

3

/

16

'' (1,300) 57

3

/

16

'' (1,453)

C — — — 40½'' (1,029) 52½'' (1,344) 58½'' (1,486)

Table 1: Custom Insert Overall Dimensions

20

5/

8

"

(524)

21

3/

4

"

(553)

4

5

/

16

"

(110)

11

1

/

8

"

(283)

16

5

/

8

"

(422)

22"

(559)

12

13/

16

"

(325)

10

1

/

4

" (260)

5

13/

16

"

(148)

dia. 10"

(dia. 254)

A

B

5

1

/

8

"

(130)

7

11/

16

"

(195)

Custom Insert – without liner

23

5/

16

"

(592)

20

5/

8

"

(524)

21

3/

4

"

(553)

4

5

/

16

"

(110)

11

1

/

8

"

(283)

16

5

/

8

"

(422)

24

3/

4

"

(629)

14

5/

16

"

(364)

1

1/

2

"

(38)

10

1

/

4

" (260)

5

13/

16

"

(148)

dia. 10"

(dia. 254)

A

B

C

7

11/

16

"

(195)

5

1

/

8

"

(130)

Custom Insert – with liner

inches (millimeters)

English 5

Installation Preparation

Installation Considerations

The custom insert unit is designed for installation inside a

custom-built hood assembly. It is for ducting to the outside.

It cannot be used in conjunction with a recirculation unit.

Hood installation height above a cooktop, rangetop or

range can vary. To obtain the necessary installation height

above a cooktop, rangetop or range, consult the

appliance's installation manual.

NOTICE:

The hood could incur some damage from heat if a

THERMADOR PROFESSIONAL

®

series range or rangetop

is operated with multiple burners at high settings under a

hood that is installed at minimum clearances.

Hood Width

The hood width should be no less than the width of the

cooking surface. For proper performance, the housing must

cover the entire cooking surface.

Where space is not restricted, a wider hood can be used to

increase capture area.

Distance From Cooking Surface

The installation height ranges from a minimum height of

30'' (762 mm) to a maximum height of 40'' (1,016 mm);

however, it is necessary to follow the cooking appliance

manufacturer’s installation instructions for proper hood

height.

Unit Weight

When calculating the load for the housing support system,

be sure to consider the weight of the ventilation unit.

Figure 1: Typical Hood Installation

Cooking

Surface

* Hood width should be no less

than the width of the cooking

surface.

E

* Follow cooking appliance

manufacturer’s recommendations

* 30" (762) min.

40" (1,016) max.

to Cooking Surface

* 30" (762) min.

40" (1,016) max.

to Cooking Surface

* 30" (762) min.

40" (1,016) max.

to Cooking Surface

18"

(457)

10¼"

(260)

10¼"

(260)

10¼"

(260)

i

meters)

Model Weight

VCIN36JP 60 lb (27.22 kg)

VCIN48JP 73 lb (33.11 kg)

VCIN54JP 82 lb (37.20 kg)

VCIB36JP 96 lb (43.54 kg)

VCIB48JP 111 lb (50.35 kg)

VCIB54JP 122 lb (55.34 kg)

IMPORTANT:

The supplied weights address only the ventilation unit and

blower. Installer must account for weight of any materials

of construction when calculating the total dead weight

load of installation, including but not limited to: wall, tile,

mortar, plaster, brick, finishes, partitions, and other

similarly incorporated architectural and structural items. It

is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Table 2: Unit Weight with Blowers

English 6

Blower Motors

VCIN models are shipped without the blower motor.

Internal, in-line and remote blowers are available through

your authorized THERMADOR

®

dealer. For local dealer

information, visit the Find a Dealer section of our website at

www.thermador.com.

The blower will vary in size and is dictated by the cooking

surface, the volume of air that needs to be moved and the

length of the duct run. Refer to “Blower Motor Installation”

on page 10 for detailed blower motor information.

Backsplash

Optional stainless steel backsplashes are available for

purchase in widths to match all custom insert hoods

through your authorized THERMADOR

®

dealer. For local

dealer information, visit the Find a Dealer section of our

website at www.thermador.com.

Ductwork Preparation

Discharge Direction

The exhaust air is discharged upwards through a duct.

Ducting Recommendations

Proper performance is dependent upon proper ducting.

Local building codes may require the use of make-up air

systems when using ducted ventilation systems greater

than speci¿ed cubic feet per minute (CFM) of air

movement. The speci¿ed CFM varies from locale to locale.

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

DO NOT USE FLEXIBLE DUCT; it creates back pressure/

air turbulence and reduces performance.

Always install a metal vent cover where the ductwork exits

the house.

COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold air

flow and a nonmetallic thermal break to minimize

conduction of outside temperatures as part of the ductwork.

The damper should be on the cold air side of the thermal

break. The break should be as close as possible to where

the ducting enters the heated portion of the house.

MAKE-UP AIR: Local building codes may require the use

of make-up air systems when using ducted ventilation

systems greater than specified CFM of air movement. The

specified CFM varies from locale to locale. It is the

responsibility of the owner and the installer to determine if

additional requirements and/or standards apply to specific

installations.

For safety reasons, ducting should vent directly outdoors

(not into an attic, underneath the house, into the garage or

into any enclosed space). The unit cannot be used in

conjunction with a recirculation unit.

THERMADOR

®

recommends not exceeding 50 ft

(15.24 m) of duct.

Keep duct runs as short and straight as possible. Elbows

and transitions fittings reduce air flow efficiency. Back to

back elbows and “S” turns give very poor delivery and are

not recommended.

A short, straight length of duct at the inlet of a remote

blower gives the best delivery.

Hoods are supplied with a 10" (254 mm) round transition. A

locally supplied transition is required for other sizes.

Use Table 3 on page 7 to compute permissible lengths for

duct runs to outdoors.

English 7

Equivalent Duct Lengths for Commonly Used Transitions

Smooth

Straight

6 1.2

7 0.95

8 0.7

10 0.6

3¼" x 10"

Straight

N/A 1

3¼" x 14"

Straight

N/A 0.7

90° Elbow

Round

612

78

86

45° Elbow

Round

65

74

83

3¼" x 10"

90° Elbow

Round

N/A 5

3¼” x 10"

45° Elbow

Round

N/A 15

3¼" x 10"

Flat Elbow

N/A 20

Round to

3¼" x 10"

61

71

3¼" x 10"

to Round

65

73

Round to

3¼" x 10"

90° Elbow

610

78

3¼" x 10"

to Round

90° Elbow

610

75

3¼" x 10"

Center Reverse

Elbow Left

N/A 15

3¼" x 10"

Center Reverse

Elbow Right

N/A 25

3¼" x 10" Left

Reverse Elbow

N/A 15

3¼" x 10"

Right Reverse

Elbow

N/A 25

Round

Wall Cap

62

72

82

10 2

Round

Roof Cap

62

72

82

2' Long

3¼" x 10"

Flex

N/A 20

3¼" x 10"

to Round

10 1

7" Inline

Backdraft

Damper

7

3¼" x 10"

Roof Jack

and Shutter

N/A

NOTE: These commonly used installation parts can be purchased

at a local hardware store. THERMADOR® does not manufacture all

these parts.

Duct Piece

Size of Duct

Piece (in)

Duct Piece

Size of Duct

Piece (in)

Equivalent

Length (ft)

Equivalent

Length (ft)

Table 3: Duct Lengths

English 8

Hood Transition

Assembly of the Transition

1. A minimum height clearance of 10¼'' (260 mm) is

needed above the hood for transition mounting.

2. Remove transition from inside of hood. Discard

brackets attaching transition to the inside of hood.

3. Align mounting holes at base of transition with the

mounting holes of the 1/2'' (13 mm) flange located at

the top or rear of the hood (Figure 5).

4. Fasten transition to hood using two (2) 1'' (25.4 mm)

sheet metal screws included with hood (Figure 5).

5. Seal connection between transition and hood with

aluminum tape. DO NOT use duct tape (Figure 5).

6. Remove tape holding damper closed.

Figure 2: Transition Dimensions

Figure 3: Hood Transition Dimensions

Figure 4: Transition Height

10" (254 mm)

Duct

21¾" (553 mm)

21¾" (

553 mm)

21¾" (553 mm)

4

5

16

(110 mm)

/ "

1" (25.4 mm)

x 2

4

5/

16

"

(502 mm)

21¾ʺ

(552 mm)

21¾ʺ

(552 mm)

21¾ʺ

(552 mm)

17½ʺ

(444 mm)

17½ʺ

(444 mm)

17½ʺ

(444 mm)

10¼ʺ

(260 mm)

12

13

/

16

ʺ

(325 mm)

Figure 5: Transition Connection

English 9

Electrical Requirements

The unit requires a 120V AC, 60Hz. 15A branch circuit.

The hood should only be connected to a grounded socket

that has been installed according to relevant regulations. If

possible, place the grounded socket directly behind the

chimney paneling. Attach the grounded socket as close to

the appliance as possible and in an accessible location.

• The grounded socket should be connected to its own

circuit.

• If the grounded socket is no longer accessible following

installation of the hood, make sure that an electrical

switch is permanently installed for turning off the

appliance.

When connected to a GFCI-protected supply,

THERMADOR PROFESSIONAL

®

custom insert hoods are

suitable for use in damp locations that are protected from

outside weather conditions and not subject to saturation

with water and other liquids, but can be subject to

moderate degrees of moisture (such as an outdoor covered

patio or lanai area). Refer to local codes, NEC/CEC, and or

the Authority Having Jurisdiction (AHJ) for additional

information.

Check your local building codes for proper method of

installation. In the U.S., if there are no applicable local

codes, this unit should be installed in accordance with the

National Electric Code ANSI/NFPA No. 70, Current Issue.

In Canada, installation must be in accordance with the CAN

1- B149.1 and .2 - Installation Codes for Gas Burning

Appliances and/or local codes.

The appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing a wire that allows the electric current to

escape. This appliance has a cord with a ground wire and

grounded plug. The plug must be plugged into an outlet

that is properly installed and grounded.

Electrical Data

Data, including the model and serial number, is located on

the product data rating plate inside the appliance, visible

after removal of the filter frame (see Figure 39 on page 23).

Choosing the Correct

Blower

A variety of interior and exterior blower options (Remote,

Inline or Integral) are available for THERMADOR

PROFESSIONAL

®

Custom Insert series hoods. If the unit

you have selected does not have a blower included, one

must be purchased separately.

It is recommended to use only THERMADOR blowers with

THERMADOR ventilation hoods. See the Ventilation

Planning Guide for recommended blowers. Contact

Customer Service for additional options (see the back page

for contact information).

Blower selection will vary based on the volume of air that

needs to be moved and the length and location of the duct

run. For long duct runs with multiple turns and bends,

consider using a more powerful blower. For the most

efficient air-Àow exhaust, use a straight run or as few

elbows as possible (refer to “Ductwork Preparation” on

page 6).

Integral Blowers

These blowers are integrated into the hood at the time of

installation (included with the VCIB model units).

Remote Blowers

Depending on preference and ducting situation, these

blowers can be mounted on the roof or exterior wall of the

home. An exterior installation may be more appealing to

reduce noise in the kitchen.

Inline Blowers

To minimize noise in the kitchen, these blowers are

mounted along the duct line anywhere between the kitchen

and the exterior wall. If there is easy access to duct line (in

an attic, for example), this may be an appealing option.

WARNING

The appliance must be grounded.

English 10

Installation Instructions

Blower Motor Installation

Integral blower installation only

1. The blower is attached to the hood using weld studs on

the mounting plate. Figure 6 exhibits the weld stud

locations.

2. Guide the motor mounting plate over the studs.

3. Attach four (4) nuts (included with hood) to the weld

studs. Tighten nuts to secure the blower to the hood.

25 ft. Blower Cable Connection Accessory

Kit

(optional)

The blower extension cable is compatible with the

following Inline & Remote blowers:

Blower SKU

Voltage

(Ac)

Blower

Current

(Amps)

**Circuit

Breaker

(Amps)

Integral VTN630* 120 2.7 15

Integral VTN1030* 120 5.4 15

Remote VTR630* 120 4.2 15

Remote VTR1030* 120 5.7 15

Remote VTR1330* 120 8.5 15

Inline VTI610* 120 4.2 15

Inline VTI1010* 120 5.7 15

* Indicates a letter designating the release year.

** With blower installed.

Figure 6: Weld Stud Location

x 4

Weld Studs

Figure 7: Junction Box Location

Blower SKU

Remote Blower VTR630*

Remote Blower VTR1030*

Remote Blower VTR1330*

Inline Blower VTI610*

Inline Blower VTI1010*

*Indicates a letter designating the release year.

EXTNCB25 Parts Included

1 – 25 ft. cable

1 – Adapter Cable No. 1

(NOT NEEDED FOR VCIN OR

VCIB MODEL CONNECTIONS)

1 – Adapter Cable No. 2

(NOT NEEDED FOR VCIN OR

VCIB MODEL CONNECTIONS)

IMPORTANT: CUTTING OFF A CONNECTOR TO THE

APPLIANCE OR TO THE EXTENSION CABLE KIT

WILL VOID THE WARRANTY.

Knockouts

Junction Box

English 11

Blower Extension Cable Connection

The internal blower harness should be routed through the

knockout and secured with a 1'' (25.4 mm) strain relief. The

remote harness can then be connected to the blower

harness outside the unit.

Wiring the Hood with an

Integral Blower

Integral Blower models VTN630 and VTN1030 are

integrated into the hood at the time of installation (VCIN

models). For complete installation instructions see the

instructions supplied with the blower unit.

1. Remove junction box channel covering the wires (see

Figure 7 on page 10).

2. Remove circular knockouts (Figure 7 on page 10).

3. Connect the blower’s Molex plug connector to the

connector present inside the hood, as shown in

Figure 10.

4. Install 1'' (25.4 mm) conduit connector in junction box.

5. Run black, white, and green wires (#12 AWG) in 1''

(25.4 mm) conduit from the power supply to the

junction box.

6. Connect the power supply wires to the hood wires in

the following order: black to black, white to white, and

green wire to green ground screw on chassis. Use

spring type wire nuts.

• Spring type wire nuts rated for a minimum of two

(2) #18 gauge wires and maximum of four (4) #14

gauge wires, UL & CSA rated to 600V and 302°F

(150°C.)

7. Close the junction box cover.

Figure 8: 25ft Cable

Figure 9: Integral Blower Model VTN1030

25ft cable

Connects to

VCIxxJP hood

A

B

Connects to

Remote or

Inline blower

2

1/

4

"

(57)

6

7/

8

"

25"

(635)

6

3/

4

"

(171)

8

7/

8

"

(225)

4

1/

8

"

8

1/

4

" (210)

(175)

(105)

Figure 10: Wiring the Hood with an Integral Blower

From Control Panel

From Blower

English 12

Wiring the Hood with a

Remote Blower

Custom insert models can be installed with remote blowers

(VCIN models). For complete installation instructions see

the instructions supplied with the blower unit.

1. Remove junction box channel covering the wires (see

Figure 7 on page 10).

2. Remove circular knockouts (Figure 7 on page 10).

3. Install 1'' (25.4 mm) conduit connectors.

4. Run black, white, and green wires (#12 AWG) in 1''

(25.4 mm) conduit from the power supply to the

junction box.

5. Connect the power supply wires to the hood wires in

the following order: black to black, white to white, and

green wire to green ground screw on chassis. Use

spring type wire nuts.

• Spring type wire nuts, rated for a minimum of two

(2) #18 gauge wires and maximum of four (4) #14

gauge wires, UL & CSA rated to 600V and 302°F

(150°C).

6. Connect the “pigtail” to the connector inside the

junction box.

7. Close the junction box cover.

8. Run five (5) #14 AWG wires in 1'' (25.4 mm) conduit

from the remote blower to the second conduit

connector.

9. Connect the remote blower to the pigtail wires as

shown in Figure 12. Connect the remote blower green

(ground) wire to the ground screw in the junction box.

Refer to the blower installation instructions for further

wiring details.

Wiring the Hood with an

Inline Blower

Both VCIN and VCIB custom insert models can be installed

with inline blowers. For complete installation instructions

see the instructions supplied with the blower unit.

1. Remove junction box channel covering the wires (see

Figure 7 on page 10).

2. Remove circular knockouts (Figure 7 on page 10).

3. Install 1'' (25.4 mm) conduit connectors.

4. Run black, white, and green wires (#12 AWG) in 1''

(25.4 mm) conduit from power supply to junction box.

5. Connect the power supply wires to the hood wires in

the following order: black to black, white to white, and

green wire to green ground screw on chassis. Use

spring type wire nuts.

• Spring type wire nuts, rated for a minimum of two

(2) #18 gauge wires and maximum of four (4) #14

gauge wires, UL & CSA rated to 600V and 302°F

(150°C).

Figure 11: VTR1330 Remote Blower

Figure 12: Wiring the Hood with a Remote Blower

19

7/

8

"

(505)

2

1/

8

"

(54)

10"

(254)

2

1/

8

"

(54)

20

3/

4

"

(527)

12

7/

8

"

(327)

12

1/

8

"

(308)

6

1/

2

"

(165)

1

7/

8

"

(48)

13

5/

8

"

(346)

dia. 9

7/

8

"

(251)

SPEED 1

SPEED 2

SPEED 3

NEUTRAL

RD

BU

BN

WH

SP4

GROUND

N

SP1

SP2

SP3

Brown

Green/Yellow

White

Red

Blue

Orange

WH / BC / BL (16 AWG)

BK / N / NE (16 AWG)

120V, 60HZ, 20A

POWER SUPPLY

L1NT1T2S3

Figure 13: VTI1010 Inline Blower

12

1/

8

"

(308)

14

3/

8

"

(365)

7/

8

" (22)

1

3/

4

"

(44)

19

1/

8

"

(486)

ø9

7/

8

"

(251)

12

"

(305)

12

7/

8

"

(327)

English 13

6. Connect the “pigtail” to the connector inside the

junction box.

7. Close the junction box cover.

8. Run five (5) wires (#14 AWG) in 1'' (25.4 mm) conduit

from the inline blower to the second conduit connector.

9. Connect the inline blower to the pigtail wires as per

Figure 14. Connect the inline blower green (ground)

wire to the ground screw in the junction box.

Remote Control Installation

(optional)

NOTE: When using the Custom Insert with the optional

remote control, the unit loses the “AUTO” function and

the over-temperature heat sensor described in the Use

& Care Guide.

It is recommended that the Remote Control be wired to the

hood after the hood is installed.

1. Access wiring

a) Remove filters, spacers and grease trays.

b) Remove the junction box cover (refer to Figure 7

on page 10).

c) Remove three screws holding stainless steel panel

to the canopy.

d) Remove core partition (Figure 16).

2. Connecting the harness to the relay board.

a) Unplug harness from the remote control to the

relay board (Figure 17).

b) Plug in harness included in the remote kit

(Figure 17).

c) Run harness through core partition hole

(Figure 18).

Figure 14: Wiring the Hood with an Inline Blower

Figure 15: Remove stainless steel panel

SPEED 1

SPEED 2

SPEED 3

NEUTRAL

RD

BU

BN

WH

SP4

GROUND

N

SP1

SP2

SP3

Brown

Green/Yellow

White

Red

Blue

Orange

WH / BC / BL (16 AWG)

BK / N / NE (16 AWG)

120V, 60HZ, 20A

POWER SUPPLY

L1NT1T2S3

Figure 16: Remove core partition

Figure 17: Relay Board Hookup

Figure 18: Wire Routing through Partition

English 14

d) Reinstall core partition after running the harness

through the access hole.

e) Insert remote harness end into the mounting hole,

as indicated in Figure 19, until it clicks.

f) Connect the extension harness to the connector

inside the junction box.

3. Prepare wall (or similar surface) cutout for installation

as shown below in Figure 21.

4. Connect the remote control to extension harness with

the included 30 ft (914.4 cm) cable.

5. Insert remote control into cutout. Secure from behind

with two (2) nuts onto the weld studs (Figure 22).

6. Reinstall hood components from Figure 15 and

Figure 16.

Figure 19: Remote Harness Mounting Hole

Remote

Harness

Remote

Harness

Remote

Harness

Mounting

Hole

Harness

Mounting

Hole

Harness

Mounting

Hole

Figure 20: Pigtail Remote Connection

Figure 21: Wall Cutout (view is shown facing wall)

11¾ʺ

(298 mm)

11

/

16

ʺ

(17 mm)

¼ʺ

(6 mm)

1½ʺ

(40 mm)

1½ʺ

(40 mm)

1½ʺ

(40 mm)

(17 mm)

(15 mm)

9

/

16

ʺ

5

/

8

ʺ

1½ʺ

(40 mm)

1½ʺ

(40 mm)

1½ʺ

(40 mm)

10

(263 mm)

3

/

8

ʺ

11

/

16

ʺ

(17 mm)

2¾ʺ

(69 mm)

(23 mm)

15

/

16

ʺ

1

(35 mm)

1

(35 mm)

1

(35 mm)

3

/

8

ʺ

1

(35 mm)

1

(35 mm)

1

(35 mm)

3

/

8

ʺ

(10 mm)

3

/

8

ʺ

(5 mm)

3

/

16

ʺ

Figure 22: Remote Install

English 15

Preparing the Ceiling Cutout and Housing

The unit must be mounted to the surrounding housing. See “Installation Preparation” on page 5 for suggestions on

determining hood height.

When calculating the load for the housing support system, be sure to include the weight of the ventilation unit. See Table 2

on page 5 for unit weight by model.

Build housing in accordance with the dimensions noted in Figure 26 thru Figure 28.

Transition and Conduit Cutout Dimensions

Model A B C

36'' without Liner 14

3

/

16

'' (360 mm) 1ǩ'' (29 mm) 1Ǭ'' (47 mm)

48'' without Liner 19

13

/

16

'' (503 mm) 1ǩ'' (29 mm) 1Ǭ'' (47 mm)

54'' without Liner 22

13

/

16

'' (579 mm) 1ǩ'' (29 mm) 1Ǭ'' (47 mm)

36'' with LINER236 14

3

/

16

'' (360 mm) 3

3

/

16

'' (81 mm) 1ǩ'' (29 mm)

48'' with LINER248 19

13

/

16

'' (503 mm) 3

3

/

16

'' (81 mm) 1ǩ'' (29 mm)

54'' with LINER254 22

13

/

16

'' (579 mm) 3

3

/

16

'' (81 mm) 1ǩ'' (29 mm)

Figure 23: Transition and Conduit Cutout Dimensions

2

3/

8

"

(86)

2

3/

8

"

(86)

2

3/

8

"

(86)

Back of Hood

Back of Trim or Liner

C

L

C

L

C

L

C

B

10¼"

(260)

10¼"

(260)

10¼"

(260)

3

3/

16

"

(81 )

7

7/

8

"

" (200)

(200)

Dia. clearance holes for 1

"

(25.4) conduit to junction box

Dia. clearance holes for 1

"

(25.4) conduit to junction box

Dia. clearance holes for 1

"

(25.4) conduit to junction box

23" (584)

A

1

7/

"

(48)

8

English 16

Ceiling Cutout Dimensions

Cutout for Hood

A

inches (mm)

B

inches (mm)

36'' without Liner 32

15

/

16

'' (836)

21¼'' (540)

36'' with LINER236

39¾'' (1010)

23Ǭ'' (606)

48'' without Liner 44

15

/

16

'' (1141)

21¼'' (540)

48'' with LINER248

51¾'' (1315)

23Ǭ'' (606)

54'' without Liner 50

15

/

16

'' (1294)

21¼'' (540)

54'' with LINER254

57¾'' (1467)

23

Ǭ'' (606)

Figure 24: Cutout Dimensions

Dimensions for Optional

Liner Accessory

C

inches (mm)

D

inches (mm)

E

inches (mm)

36'' LINER236 32

7

/

16

'' (824) 39

3

/

16

'' (995)

40½'' (1029)

48'' LINER248 44

7

/

16

'' (1129) 51

3

/

16

'' (1300)

52½'' (1304)

54'' LINER254 50

7

/

16

'' (1281) 57

3

/

16

'' (1453)

58½'' (1486)

Figure 25: Liner Dimensions

5/

8"

(16 mm)

A

B

23

5/

16

"

(592 mm)

24¾"

(629 mm)

1½"

(38 mm)

20

5/

8

"

(524 mm)

C

D

E

English 17

Supporting Stud Housing Dimensions

Hood without Liner

Dimension A

Hood with Liner

Dimension A

2ǩ'' (54 mm) 4ǫ'' (117 mm)

Figure 26: Back Stud Dimensions

A

1½'' x 3½'' x 27

13

/

16

''

(38 x 89 x 707 mm)

B ǫ'' (16 mm)

C

1½'' x 3½'' x 23Ǫ''

(38 x 89 x 594 mm)

Figure 27: Stud Dimensions

To be placed on 16"

(407) stud centers

1½” x 3½” x 44½”

(38 x 89 x 1,130 mm)

1½” x 3½” x 44½”

(38 x 89 x 1,130 mm)

1½" x 3½" x 44½"

(38 x 89 x 1,130 mm)

12½"

(318)

12½"

(318)

12½"

(318)

16" (407)

12½"

(318)

12½"

(318)

12½"

(318)

A

C

B

A

English 18

Model Dimension A Dimension B

Hood without Liner 12¼'' (311 mm) 22ǩ'' (562 mm)

Hood with Liner

14

5

/

16

'' (364 mm)

24¾'' (629 mm)

Figure 28: Side View

3ʺ

(76 mm)

A

B

La page charge ...

Thermador VCIB54JP Guide d'installation

Ce manuel convient également à

Thermador VCIB54JP Guide d'installation

dans d''autres langues

Documents connexes

Autres documents