Samsung SCC-B5394P Manuel utilisateur

User’s Guide

SCC-B5394/5395

Vari-focal Anti-Vandal Dome Camera

ENG

FRE

SPA

JAP

AB68-00688C.indb 1 2007-07-06 ｿﾀﾈﾄ 2:30:23

2

3

This symbol indicates high voltage

is present inside. It is dangerous to

make any kind of contact with any

inside part of this product.

This symbol alerts you that important

literature concerning operation and

maintenance has been included with

this product.

To prevent damage which may result in ﬁre

or electric shock hazard, do not expose this

appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter

that is speciﬁed in the speciﬁcation

sheet. Using any other adapter could

cause ﬁre, electrical shock, or damage

to the product

2. Incorrectly connecting the power

supply or replacing battery may cause

explosion, ﬁre, electric shock, or damage

to the product.

3. Do not connect multiple cameras to a

single adapter. Exceeding the capacity

may cause abnormal heat generation or

ﬁre.

4. Securely plug the power cord into the

power receptacle. Insecure connection

may cause ﬁre.

5. When installing the camera, fasten it

securely and ﬁrmly. A falling camera may

cause personal injury.

6. Do not place conductive objects (e.g.

screwdrivers, coins, metal things, etc.) or

containers ﬁlled with water on top of the

camera. Doing so may cause personal

injury due to ﬁre, electric shock, or falling

objects.

7. Do not install the unit in humid, dusty, or

sooty locations. Doing so may cause ﬁre

or electric shock.

8. If any unusual smells or smoke come

from the unit, stop using the product. In

such case, immediately disconnect the

power source and contact the service

center. Continued use in such a condition

may cause ﬁre or electric shock.

EXPLANATION OF

SAFETY RELATED SYMBOLS

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE REAR COVER. NO USER

SERVICEABLE PARTS INSIDE. REFER

TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

The lighting ﬂash and

Arrowhead within Triangle is

a warning sign alerting you of

dangerous voltage inside the

product.

The explanation point within

the triangle is a warning sign

alerting you of important

instructions accompanying the

product.

AB68-00688C.indb 2 2007-07-06 ｿﾀﾈﾄ 2:30:23

2

ENG

3

9. If this product fails to operate normally,

contact the nearest service center. Never

disassemble or modify this product

in any way. (SAMSUNG is not liable

for problems caused by unauthorized

modiﬁcations or attempted repair.)

10. When cleaning, do not spray water

directly onto parts of the product. Doing

so may cause ﬁre or electric shock.

CAUTION

1. Do not drop objects on the product or

apply strong shock to it. Keep away from

a location subject to excessive vibration

or magnetic interference.

2. If you want to relocate the already

installed product, be sure to turn off the

power and then move or reinstall it.

3. Remove the power plug from the

outlet when then there is a lightning.

Neglecting to do so may cause ﬁre or

damage to the product.

4. Keep out of direct sunlight and heat

radiation sources. It may cause ﬁre.

5. Install it in a place with good ventilation.

6.

Avoid aiming the camera directly towards

extremely bright objects such as sun, as

this may damage the CCD image sensor.

7. Apparatus shall not be exposed to

dripping or splashing and no objects

ﬁlled with liquids, such as vases, shall be

placed on the apparatus.

8. The Mains plug is used as a disconnect

device and shall stay readily operable at

any time.

FCC Statement

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

1) This device may not cause harmful

interference, and

2) This device must accept any interference

received including interference that may

cause undesired operation.

Note

This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to part 15 of FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment

is operated in a commercial environment. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment

in a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

IC Compliance Notice

This Class A digital apparatus meets

all requirements of the Canadian

interference-Causing Equipment

Regulations of ICES-003.

AB68-00688C.indb 3 2007-07-06 ｿﾀﾈﾄ 2:30:24

4

5

IMPORTANT SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and

operating instructions should be read

before the product is operated.

2. Retain Instructions – The safety and

operating instructions should be retained

for future reference.

3. Heed Warnings – All warnings on the

product and in the operating instructions

should be adhered to.

4. Follow Instructions – All operating and

use instructions should be followed.

5. Cleaning – Unplug this product from the

wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use

a damp cloth for cleaning.

6. Attachments – Do not use attachments

not recommended by the product

manufacturer as they may cause

hazards.

7. Water and Moisture – Do not use this

product near water – for example, near

a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near

a swimming pool; and the like.

8. Accessories – Do not place this product

on an unstable cart, stand, tripod,

bracket, or table. The product may fall,

causing serious injury to a child or adult,

and serious damage to the product.

Use only with a cart, stand, tripod,

bracket, or table recommended by the

manufacturer, or sold with the product.

Any mounting of the product should

follow the manufacturer’s instructions,

and should use a mounting accessory

recommended by the manufacturer.

9. A product and cart combination should

be moved with care. Quick stops,

excessive force, and uneven surfaces

may cause the product and cart

combination to overturn.

10. Ventilation – Slots and openings in the

cabinet are provided for ventilation and to

ensure reliable operation of the product

and to protect it from overheating, and

these openings must not be blocked or

covered. The openings should never be

blocked by placing the product on a bed,

sofa, rug, or other similar surface. This

product should not be placed in a built-in

installation such as a bookcase or rack

unless proper ventilation is provided or

the manufacturer’s instructions have

been adhered to.

11. Power Sources – This product should

be operated only from the type of power

source indicated on the marking label.

If you are not sure of the type of power

supply to your home, consult your

product dealer or local power company.

For products intended to operate from

battery power, or other sources, refer to

the operating instructions.

12. Grounding or Polarization – This product

may be equipped with a polarized

AB68-00688C.indb 4 2007-07-06 ｿﾀﾈﾄ 2:30:24

4

ENG

5

alternating-current line plug (a plug

having one blade wider than the other).

This plug will ﬁt into the power outlet

only one way. This is a safety feature.

If you are unable to insert the plug fully

into the outlet, try reversing the plug.

If the plug should still fail to ﬁt, contact

your electrician to replace your obsolete

outlet. Do not defeat the safety purpose

of the polarized plug. Alternate Warnings

– This product is equipped with a three-

wire grounding-type plug, a plug having

a third (grounding) pin. This plug will only

ﬁt into a grounding-type power outlet.

This is a safety feature. If you are unable

to insert the plug into the outlet, contact

your electrician to replace your obsolete

outlet. Do not defeat the safety purpose

of the grounding-type plug.

13. Power-Cord Protection – Power-supply

cords should be routed so that they are

not likely to be walked on or pinched

by items placed upon or against them,

paying particular attention to cords at

plugs, convenience receptacles, and the

point where they exit from the product.

14. Protective Attachment Plug – The

product is equipped with an attachment

plug having overload protection. This is

a safety feature. See Instruction Manual

for replacement or resetting of protective

device. If replacement of the plug is

required, be sure the service technician

has used a replacement plug speciﬁed

by the manufacturer that has the same

overload protection as the original plug.

15. Outdoor Antenna Grounding – If an

outside antenna or cable system is

connected to the product, be sure the

antenna or cable system is grounded so

as to provide some protection against

voltage surges and built-up static

charges. Article 810 of the National

Electrical Code, ANSI/NFPA 70, provides

information with regard to proper

grounding of the mast and supporting

structure, grounding of the lead-in wire

to an antenna discharge unit, size

of grounding conductors, location of

antenna-discharge unit, connection to

grounding electrodes, andrequirements

for the grounding electrode.

16. Lightn

ing – For added protection for this

product during a lightning storm, or when

it is left unattended and unused for long

periods of time, unplug it from the wall

outlet and disconnect the antenna or

cable system. This will prevent damage

to the product due to lightning and

power-line surges.

GROUND

CLAMP

ANTENNA LEAD

IN WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION S10-20)

GROUNDING CONDUCTORS

(NEC SECTION S10-21)

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUND CLAMPS

ELECTRIC

SERVICE

EQUIPMENT

NEC - NATIONAL ELECTRICAL CODE

AB68-00688C_Eng.indd 5 2007-07-06 ｿﾀﾈﾄ 5:58:58

6

7

17. Power Lines – An outside antenna

system should not be located in the

vicinity of overhead power lines or other

electric light or power circuits, or where it

can fall into such power lines or circuits.

When installing an outside antenna

system, extreme care should be taken

to keep from touching such power lines

or circuits as contact with them might be

fatal.

18. Overloading – Do not overload wall

outlets, extension cords, or integral

convenience receptacles as this can

result in a risk of ﬁre or electric shock.

19. Object and Liquid Entry – Never push

objects of any kind into this product

through openings as they may touch

dangerous voltage points or short-out

parts that could result in a ﬁre or electric

hock. Never spill liquid of any kind on the

product.

20. Servicing – Do not attempt to service this

product yourself as opening or removing

covers may expose you to dangerous

voltage or other hazards. Refer all

servicing to qualiﬁed service personnel.

21. Damage Requiring Service – Unplug this

product from the wall outlet and refer

servicing to qualiﬁed service personnel

under the following conditions:

a) When the power-supply cord or plug

is damaged,

b) If liquid has been spilled, or objects

have fallen into the product,

c) If the product has been exposed to

rain or water,

d) If the product does not operate

normally by following the operating

instructions. Adjust only those controls

that are covered by the operating

instructions as an improper adjustment

of other controls may result in damage

and will often require extensive work

by a qualiﬁed technician to restore the

product to its normal operation,

e) If the product has been dropped or

damaged in any way, and

f) When the product exhibits a distinct

change in performance – this indicates a

need for service.

22. Replacement Parts – When replacement

parts are required, be sure the service

technician has used replacement parts

speciﬁed by the manufacturer or have

the same characteristics as the original

part. Unauthorized substitutions may

result in ﬁre, electric shock, or other

hazards.

23. Safety Check – Upon completion of any

service or repairs to this product, ask

the service technician to perform safety

checks to determine that the product is

in proper operating condition.

24. Wall or Ceiling Mounting – The

product should be mounted to a wall

or ceiling only as recommended by the

manufacturer.

25. Heat – The product should be situated

away from heat sources such as

radiators, heat registers, stoves, or

other products (including ampliﬁers) that

produce heat.

Apparatus shall not be exposed to

dripping or splashing and no objects

ﬁlled with liquids, such as vases,

shall be placed on the apparatus

AB68-00688C_Eng.indd 6 2007-07-06 ｿﾀﾈﾄ 5:58:58

6

ENG

7

Overview ...........................................................................................

8

About this guide ............................................................................8

Product overview ...........................................................................8

Main features .................................................................................8

Components ...................................................................................9

Checking components in the package .......................................9

Components of your camera ....................................................10

Installation .....................................................................................

11

Setting switches ..........................................................................11

Setting function switches ..........................................................11

Connecting cables and changing the settings .........................13

Installing camera .........................................................................14

Before installation .....................................................................14

About the installation holes ......................................................14

Installing on a pipe ...................................................................15

Installing the camera on the ceiling ..........................................17

Disassembling/assembling the Main body from the Case .......18

Adjusting the camera direction ..................................................19

Appendix A: Speciﬁcations for NTSC Standard .................

21

Appendix B: Speciﬁcations for PAL Standard ..............

22

Contents

AB68-00688C.indb 7 2007-07-06 ｿﾀﾈﾄ 2:30:44

8

9

Overview

❚

About this guide

This user guide includes basic instructions for

the product. It is recommended that all users

read this guide before use.

This guide is divided as follows:



Chapter 1, “Overview,” introduces the user guide

and product related information. (This chapter)



Chapter 2, “Installation,” explains how to set and

install the product.



Appendix, “Speciﬁcations,” provides the

speciﬁcations

of the product.

❚

Product overview

This anti-vandal dome camera provides

the superb monitoring features in bank and

business areas and it is a water-proof and

vibration-proof camera, which can strongly

endure an external impact. This vari-focal

camera provides the digital noise reduction

(DNR) and real-time CCD defect correction

features for implementing a clear image.

❚

Main features



Power: DC 12V/AC 24V



Special functions



Line lock (LL) control



Auto white balancing



Horizontal/vertical image reversing



Flickerless control



Low shutter speed control



Backlight compensation control



Automatic switching between color and black

& white modes



Equipped with vari-focal lens



Auto Iris function



Digital noise reduction (DNR)



Dynamic CCD defect compensation

AB68-00688C.indb 8 2007-07-06 ｿﾀﾈﾄ 2:30:44

8

ENG

9

❚

Components

Checking components in the package

Please check your camera and accessories are included in the package. Those components

are as shown below:

Camera Test Monitor Cable User’s Guide

Image Part name Standard Quantity Usage

Plastic anchor HUD 5 4 (EA)

Attach each piece to screw connection

holes for strengthening connection

ASSY screw

machine

BH M5 X L6.

(White+o-ring)

8

Used for ﬁlling in the holes when

installing pipe and wall mount

ASSY screw

tapping

TH M4xL30 (Black+

o-ring)

4

Used when installing your camera

on the ceiling or wall

L-Wrench TROX T-20 1

Used for assembling/

disassembling the Dome cover

Template 1 Used for guiding the installation

Gasket-pipe hole T2.5 W56 1

Used to make a wiring hole when

installing the camera on the

ceiling or wall

Note

The test monitor cable is used to test the camera by connecting to a portable display. If you really want to

connect the camera to a monitoring display, use the BNC cable.

AB68-00688C_Eng.indd 9 2007-08-13 ｿﾀﾀ・10:48:05

10

11

Components of your camera

Your camera has the following components:

1. Dome cover: Covers the inner cover, lens, and main

body to protect them.

2. Cover screw: Use it to assemble or disassemble both

dome cover and case.

3. Inner cover

: Covers the main body to protect it.

4. Wing locker

: Push a long thin screwdriver into its

narrow spot and press it outward when you want to

remove the inner cover.

5. Main body

: Includes a lens, a switch board, a PCB

board, screws, and such.

6. Screws for assembly and disassembly

: Using

these 2 screws, the Main body is closely connected to

the Case.

7. Hooker

: By pulling the left/right levers in the arrow

direction, the Main body can be detached from the

Case.

8. Case: Used as a ceiling or wall ﬁxture. It is ﬁxed using

four screws provided in the package.

9. Zoom lever: Using this lever, the lens zoom can be

adjusted and ﬁxed.

10. Focus lever: Using this lever, the lens focus can be

adjusted and ﬁxed.

11. Tilt ﬁxing screw: Using this screw, the slope of the

lens can be adjusted and ﬁxed.

12. Switch board

: Includes two kinds of control switches

such as function switches and phase-control switches.

The board has eight function switches in the middle

and two phase-control buttons on each side of the

function switch area.

13. Cable: Connect the Video connector to BNC cable

and Power connector to power adapter.

1

2

4

Lens

9 0

!

@

3

8

#

Video connector

Power connector

5

6

7

AB68-00688C.indb 10 2007-07-06 ｿﾀﾈﾄ 2:30:48

10

ENG

11

❚

Setting switches

Setting function switches

To set the available functions on your camera, adjust eight switches as shown below:

Installation

1. Switch 1 (LL): When this switch is set to

OFF, the camera operates in the internal

synchronization mode, while when it is

set to ON, the camera operates in the

line lock mode.

In the internal synchronization mode, the

camera always uses an inside crystal

oscillator for synchronization. However

if multiple cameras are connected to a

sequential switcher, picture rolling or

ﬂickering may occur when switching from

one camera to another. In this case, you

can set this switch to ON to solve this

problem.

The line lock mode allows the camera

to use the phase of the AC power as

the synchronization reference. In this

mode, you can use the phase control

buttons(INC/DEC).

Note

When you are using the DC 12V power, set

this switch to OFF. The line lock feature will

not normally operate even when the switch is

set to ON.

No Name Brief description

1 LL Line lock ON/OFF

2 LSS Sens-up or Low speed shutter ON/OFF

3 H-REV Horizontal reverse ON/OFF

4 V-REV Vertical reverse ON/OFF

5 BLC Backlight compensation ON/OFF

6 FL Flickerless ON/OFF

7 D/N Automatic switching between color and

black & white ON/OFF

8 AWB Automatic white balance ON/OFF

8

7

6

5

4

3

2

1

INC

DEC

AB68-00688C.indb 11 2007-07-06 ｿﾀﾈﾄ 2:30:53

12

13

Set the LL switch to ON while the AC

power is connected. If any picture roll

happens, you have to adjust the phase

using the phase-control buttons. Press

the INC or DEC button to increase or

decrease the phase by one degree.

2. Switch 2 (LSS): This sens-up mode

accumulates the image ﬁelds in

memory to reduce noise but increase

the brightness and contrast rate. When

this switch is set to ON, the camera

automatically switches to a maximum

of 128 times of image acquisition speed

to implement a clear picture for darker

image.

3. Switch 3 (H-REV)

: When this switch is

set to ON, the camera image is reversed

horizontally. If you want to monitor your

site using a mirror, you can use this

feature to see the right image.

4. Switch 4 (V-REV)

: When this switch is

set to ON, the camera image is reversed

vertically. If your camera reluctantly

displays the vertically reversed image,

you can use this feature to see the right

image.

5. Switch 5 (BLC)

: When this switch is set

to ON, you can view a clear image even

though the camera faces any excessive

light such as sunlight and ﬂuorescent

light. When it is set to OFF, the subject

with excessive light is not clearly shown.

6. Switch 6 (FL): When this switch is set

to ON, the shutter speed is ﬁxed to

1/100 sec (for NTSC) or 1/120 sec (for

PAL) to prevent screen from ﬂickering

by the disaccordance between vertical

synchronous frequency (50Hz for NTSC,

60Hz for PAL) and on-and-off frequency

of a light.

7. Switch 7 (D/N)

: When this switch is set

to ON, the camera automatically switches

between color and B&W according to the

brightness of the vicinity.

8. Switch 8 (AWB): This switch adjusts

white balancing. When this switch is set to

ON, this camera operates in ATW mode,

and in case of OFF, this camera operates

in AWC mode.



ATW (Auto Tracking White Balance):

The color temperature is automatically

adjusted according to the environmental

change. (Approx. 2000°K to 11,000°K)



AWC (Auto White Balance Control): It

stores the color temperature just when

the switch is changed to OFF. Accordingly

color temperatures are adjusted by the

stored value.

Caution

-. The IRIS setting range for the camera is

approximately 80 to 120 IRE. It means

the camera does not provide the IRIS

full open/close feature but the restricted

variation range.

-. Use the camera after setting to the proper

level (80 IRE or above) because the IRIS

hunting may occur when the level is 75

IRE or below.

AB68-00688C.indb 12 2007-07-06 ｿﾀﾈﾄ 2:30:54

12

ENG

13

❚

Connecting cables and changing the settings

Before installing your camera, you have to adjust the lens focus, zoom, and switch settings.

To connect cables

1. Connect the BNC cable

to the Video connector

attached on your camera.

2. Connect the BNC cable

to the Video Input on a

monitor.

3. Connect the power adapter

to the Power connector

attached on your camera.

When the monitor is turned

on, the camera image

appears.

To adjust the lens focus, zoom, and function settings

1. Remove the Cover dome and Inner cover. For more details about the removing procedures,

see “Installation procedure,” in the Installing camera section on the next page.

2. Adjust the focus, zoom, and function settings of your camera using the Focus lever, Zoom

lever, and Switch board while you are viewing the image on the screen.

3. If you want to ﬁx the adjusted focus and zoom, screw up the levers.

BNC Cable

Monitor

AB68-00688C.indb 13 2007-07-06 ｿﾀﾈﾄ 2:30:54

14

15

❚

Installing camera

Before installation

Before installing your camera, you have to read the following cautions:



You have to check whether the location (ceiling or wall) can bear ﬁve times the weight of your camera.



Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise

it may cause a breakdown or ﬁre. You can use wall mount adaptor (SADT-102WM), and pole mount

adaptor (SADT-100PM) for installing the camera on the wall or pipeline.



When installing your camera, don’t allow any person to approach the installation site. If you have any

valuable things under the place, move them away.

About the installation holes

A: Use these holes when directly installing your camera

on the ceiling or wall.



While those are not used, ﬁll in the holes using the

screw machine (M5 X L6.) for waterprooﬁng.

B: Use four holes when directly installing your camera

on the junction box



You can use the 4 1/8 diameter round type junction

box for assembly. (The junction box, gasket, and

cover are separately purchased items.)

C: Use these holes when installing the wall mount

adapter (SADT-102WM)



While those are not used, ﬁll in the holes using the

screw machine (M5 X L6.) for waterprooﬁng.

The holes that are not used should be tightly

sealed up using the screws provided for

waterprooﬁng. When the screws don’t have

rubber rings inside or are not closely attached,

note that it can cause waterprooﬁng problem.

For attaching screws, see page 16

“Disassembling/assembling the Main body from

the Case.”

AB68-00688C.indb 14 2007-07-06 ｿﾀﾈﾄ 2:30:55

14

ENG

15

Installing on a pipe

Before installation, you have to be familiar with the above cautions and ﬁll in the holes that are

not used for installation.

To install your camera bottom on a pipe

1. After connecting the power and video

cables, throw them inside the pipeline

and screw the male thread pipe into

the female pipe thread in your camera

tightly to ﬁx the Main body. (In this case,

be sure to tape with Teﬂon tape before

assembly for waterprooﬁng. Be careful

for the wiring cable not to be stuck in the

connection area.)

2. Adjust the angle of the camera in search

of a better view.

1) Separate the Dome cover using the

L-Wrench provided. (To make loose the

screws, rotate counterclockwise.)

2) Adjust the lens direction. For more

information, see page 17 “Adjusting the

camera direction.”

3. Attach the Dome cover. (Screw the

connection bolts tightly using the

L-Wrench for waterprooﬁng.)



To change the SAMSUNG logo position,

move the location of the connection

rubber band as show below and rotate

for assembly. (The rotation limit is 180

degree.)

AB68-00688C.indb 15 2007-07-06 ｿﾀﾈﾄ 2:30:55

16

17

To install the camera side on a pipe

1. Pull the power and video cables through

the pipe connection hole on the camera

side

1) Remove the side cover from the Case

using a coin or minus (-) driver. (Rotate

counterclockwise.)

2) Push the power and video cables

stretched outside of the bottom hole

into the Case. And pull them out from

the side cover of the Case.

2. Attach the removed side cover to the

bottom hole and rotate it clockwise using

a coin or minus (-) driver. (Be sure to

insert the O-ring (P22 T2.4) into the hole

before assembly. The ring is necessary

for waterprooﬁng.)

3. After pulling the power and video cables

through the connection pipe, screw the

male thread pipe into the female pipe

thread in your camera tightly to ﬁx the

Main body. (In this case, be sure to tape

with Teﬂon tape before assembly for

waterprooﬁng. Be careful for the wiring

cable not to be stuck in the connection

area.)

4. Adjust the lens direction. For more

information, see page 17, “Adjusting the

camera direction.”

5. Attach the Dome cover. For more

information, see step 3 in “To install your

camera bottom on a pipe” on page 13.

AB68-00688C.indb 16 2007-07-06 ｿﾀﾈﾄ 2:30:56

16

ENG

17

Installing the camera on the ceiling

Before installation, you have to be familiar with the above cautions and ﬁll in the holes that are

not used for installation.

To install your camera bottom on a pipe

1. Attach the provided template to the place

to be installed and penetrate a hole (5mm

diameter, minimum depth 35mm) for ﬁxing

your camera to insert the provided plastic

anchor (HUD 5) to the full.

2. After connecting both power and video

cables, put them in order not to have

damage during installation.

3. Remove the Dome cover. For more

information, see step 2 in “To install your

camera bottom on a pipe” on page 13.

4. Install your camera. After aligning the hole

where the plastic anchor is inserted with

the camera installation hole, make tight

four ASSY screw-tappings where O-rings

are inserted. (If no O-rings are inserted,

water leak may happen.)

5. Adjust the camera lens direction. For

more information, see page 17, “Adjusting

the camera direction.”

6. Attach the Dome cover. For more

information, see step 3 in “To install your

camera bottom on a pipe” on page 13.

In case of wiring after penetrating

a hole on the installation site

1

Penetrate a wiring hole toward the

pipe. (Recommended hole size: within

30mm diameter)

2

Attach the gasket on the bottom of the

product as shown below. You have to

correctly align the hole with the pipe

hole.



If the hole deviates from the gasket,

water leak may happen.

Gasket

AB68-00688C.indb 17 2007-07-06 ｿﾀﾈﾄ 2:30:56

18

19

Disassembling/assembling the Main body from the Case

The holes that are not used should be tightly sealed up using the screws provided for

waterprooﬁng. To detach the Main body from the Case, follow the instructions below:

1. 1. Remove the Dome cover ﬁrst.

2. Detach the Main body of the camera

from the Case.

1) Make loose two screws by rotating

counterclockwise.

2) Detach the Main body of the camera

after unlocking by pulling the left and

right levers in the arrow direction.

3. Assemble the Main body of the camera

with the Case. (Align three alignment

grooves of the Main body with the bumps

of the Case and assemble them.)

4. Attach the Dome cover using the

L-Wrench. For more information, see step

3 in “To install your camera bottom on a

pipe” on page 13.

1)

2)

AB68-00688C.indb 18 2007-07-06 ｿﾀﾈﾄ 2:30:57

18

ENG

19

❚

Adjusting the camera direction

When the camera is ﬁxed on the ceiling, you can

adjust the camera viewing angle. You can rotate

your camera leftward or rightward (Panning), and

can change the slope of your camera upward or

downward (Tilting).

In case of panning, the rotation limit of your camera

is set to 355 degree (100 degree clockwise and 255

degree counterclockwise). The rotation is stopped

by the Stopper inside of the camera. For panning

control, ﬁrst unfasten two screws located on the

bottom and rotate in the direction you want, and then

fasten them to ﬁx the camera.

In case of tilting, you can change the slope of your

camera from zero to 90 degree. However if the slope

angle is under 17 degree, you can encounter a partial image hide problem. To ﬁx the location

after adjusting the tilting angle, use the Tilt ﬁxing screws.

To adjust the focus and zoom of your camera, use the

Zoom lever and Focus lever. When you

install the camera on the inclined ceiling or wall, you can rotate the camera lens to see a correct

direction image.

Panning

Tilting

Lens rotation

AB68-00688C.indb 19 2007-07-06 ｿﾀﾈﾄ 2:30:59

20

21

SCC-B539X

AB68-00688C.indb 20 2007-07-06 ｿﾀﾈﾄ 2:31:00

La page charge ...

Samsung SCC-B5394P Manuel utilisateur

Samsung SCC-B5394P Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents