Maytag MED6600TQ - 27 Inch Electric Washer Manuel utilisateur

Catégorie
Laveuses sécheuses
Taper
Manuel utilisateur
M_AYI'AI3®
BRAVOS TMSTEAM FABRIC CARE SYSTEM ELECTRIC DRYER
USE & CARE GUIDE
P
SECHEUSE
DE
P %
ELECTRIQUE BRAVOS TMAVEC SYSTEME
SOIN DES TISSUS A LA VAPEUR
GUIDE D'UTILISATION ET D'ENTRETIEN
FOR QUESTIONS ABOUT FEAFURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE
CAI L: 1.800.688.9900
IN CANADA, CALl: 1.800.807.6777
VISIT OUR WEBSITE AF WWW.MAYTAG.COM
IN CANADA, WWW.MAY EAG.CA
AlJ CANADA, POUR ASSISTANCE, INS [ALl AFION OU SERVICE, COMPOSEZ I E : 1.800.807.6777
OU VISIIEZ NOTRE SIIE INTERNE] ,_,
WWW.MAY lAG .CA
PARA OBTENER ACCESO AI MANUAL DE USO Y CUIDADO EN ESPANOL, O PARA OBTENER INFORMACI(_)N ADICIONAL ACERCA DE SU PRODUCTO, VISITE: WWW.MAYIAG.COM
TENGA LISTO SU NUMERO DE MODELO COMPLETO. PIJEDE ENCONTRAR El NUMERO DE MODEl O Y DE SERIE DENTRO DE LA CAVIDAD SUPERIOR DE LA PUERTA.
W10160250A
TABLE OF CONTENTS
DRYERSAFETY.......................................................................................................................... 3
INSTALLATION INSTRUCTIONS ............................................................................................. 4
Tools and Parts....................................................................................................................... 4
l.ocation Requirements .......................................................................................................... 4
Electrical Requirements - U.S.A. Only .................................................................................... 5
Electrical Requirements - Canada Only .................................................................................. 7
Electrical Connection - U.S.A. Only ....................................................................................... 8
Venting Requirements .......................................................................................................... 14
Plan Vent System.................................................................................................................. 15
Install Vent System............................................................................................................... 16
Install l.eveling Legs ............................................................................................................. 17
Connect Vent ....................................................................................................................... 17
Connect Inlet Hose............................................................................................................... 17
l.evel Dryer .......................................................................................................................... 18
ReverseDoor Swing ............................................................................................................. 18
Complete Installation ........................................................................................................... 20
DRYER USE.............................................................................................................................. 21
Starting Your Dryer............................................................................................................... 21
Stopping, Pausing or Restarting ............................................................................................ 25¢
Drying and Cycle Tips.......................................................................................................... 23
Status Lights.......................................................................................................................... 2_¢
Cycles .................................................................................................................................. 24
Modifiers .............................................................................................................................. 25
Options ................................................................................................................................ 26
End of Cycle Signal .............................................................................................................. 26
Changing Cycles, Modifiers and Options ............................................................................. 27
Drying Rack Option ............................................................................................................. 27
DRYERCARE........................................................................................................................... 28
Cleaning the Dryer Location ................................................................................................ 28
Cleaning the I.int Screen ...................................................................................................... 28
Cleaning the Dryer Interior ................................................................................................... 29
Removing Accumulated I.int ................................................................................................ 29
Water Inlet Hoses................................................................................................................. 29
Vacation, Storage and Moving Care..................................................................................... 29
Changing the Drum [.ight ..................................................................................................... 30
TROUBLESHOOTING ............................................................................................................. 31
ASSISTANCE OR SERVICE....................................................................................................... 34
ACCESSORIES......................................................................................................................... 34
WARRANTY ............................................................................................................................ 35
TABLE DES MATIERES
S[_CURIT[_DE LA S[_CHEUSE................................................................................................... 36
INSTRUCTIONS D'INSTALLATION ....................................................................................... 38
Outillage et pi_ces ............................................................................................................... 38
Exigences d'emplacement .................................................................................................... 5¢8
Sp(!cifications (!lectriques - Pour le Canada seulement ......................................................... 40
Exigences concernant I'(!vacuation ...................................................................................... 41
Planification du syst6me d'_vacuation ................................................................................. 42
Installation du syst6me d'6vacuation .................................................................................... 44
Installation des pieds de nivellement .................................................................................... 44
Raccordement du conduit d'(!vacuation ............................................................................... 44
Raccordement des tuyaux d'alimentation ............................................................................ 44
R6glage de I'aplomb de la s_cheuse..................................................................................... 45
Inversion du sens d'ouverture de la porte ............................................................................. 46
Achever I'installation ............................................................................................................ 48
UTILISATION DE LA SI_CHEUSE............................................................................................. 49
Mise en marche de la s_cheuse............................................................................................ 49
Arr&t, pause ou remise en marche ........................................................................................ 51
Conseils pour le s_chage et les programmes ........................................................................ 5I
T_moins lumineux ................................................................................................................ 52
Programmes ......................................................................................................................... 52
Modificateurs ....................................................................................................................... 54
Options ................................................................................................................................ 54
Signal de fin de programme ................................................................................................. 55
Changement des programmes, modificateurs et options ...................................................... 55
Option de grille de se!chage................................................................................................. 56
ENTrETIEN DE LA S[_cHEUSE................................................................................................ 57
Nettoyage de I'emplacernent de la s_cheuse........................................................................ 57
Nettoyage du filtre _ charpie ................................................................................................ 57
Nettoyage de I'int6rieur de la s_cheuse................................................................................ 57
Retrait de la charpie accumul6e ........................................................................................... 58
Tuyaux d'arriv(!e d'eau ......................................................................................................... 58
Precautions _ prendre avant les vacances, un entreposage ou un d_m(_nagement ............... 58
Changement de I'ampoule d'6clairage du tambour .............................................................. 58
DI_PANNAGE .......................................................................................................................... 59
ASSISTANCE OU SERVICE...................................................................................................... 62
ACCESSOIRES.......................................................................................................................... 62
GARANTIE ............................................................................................................................... 63
2 ii__i_iii¸iiiiiiiiiiiiiiiiiiiiiii!i!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!ii:iiiiiiii:ii:iiiiiiii!iii!iiiiliiiiiiii!!iiii:iiiiiiliiiiiiiiiiiiil_iiiiiiiiiiiiii:iillill:!iiiiii_iiiii
i_i_!iii_i_iiIi!iiiiIi!iiiiIi!iiiiIi!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii_)!_}(iiii!!_!_!_!_!_!_!_!_!_!_!_!_i_¸ 4i_ i!i!_iii_1i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i!!!_iiiiiiiiiiiiiiiiiiiiiiiiiiii_;:_i!i
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY iNSTRUCTiONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
[] Read all instructions before using the dryer.
[] Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
[] Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
[] Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
[] Do not reach into the dryer if the drum is moving.
[] Do not install or store the dryer where it will be exposed
to the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
[] Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
[] Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[] Clean lint screen before or after each load.
[] Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
[] The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
[] See installation instructions for grounding requirements.
SAVETHESEINSTRUCTIONS
.... 3
Gather the required tools and parts before starting installation. Read and follow the
instructions provided with any tools listed here.
Flat-blade screwdriver
#2 Phillips screwdriver
Adjustable wrench that opens to 1"
(2.5 cm) or hex-head socket wrench
(for adjusting dryer feet)
Wire stripper (direct wire installations/
Fin snips/new vent installations/
]eve l
Vent clamps
Caulking gun and compound (for
installing new exhaust vent)
[_q)e measure
Parts supplied:
Remove parts package from dryer drum. Check that all parts were included.
A B
C D
A. Leveling I_'_s (4)
_. "Y" COl_l?eCtOr
C.Short inlet hose
D. Inlet hose with right-angle connector
E.Rubber washer
E
Parts needed:
Check local codes. Check existing electrical supply and venting and see "Electrical
Requirements" and "Venting Requirements" before purchasing parts.
Mobile home installations require metal exhaust system hardware available for purchase from
the dealer from whom you purchased your dryer. For information on ordering, please refer to
the "Assistance or Service" section. You may also contact the dealer from whom you
purchased your dryer.
If using a power supply cord:
Use a LJL listed power supply cord kit marked for use with clothes dryers. The kit should
contain:
A UI listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be
type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer
must end in ring terminals or spade terminals with upturned ends.
A UI. listed strain relief.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
You will need
A location that allows for proper exhaust installation. See "Venting Requirements."
A separate 30-amp circuit.
[f you are using a power supply cord, a grounded electrical outlet located within 2 ft
(61 cm) of either side of the dryer. See "Electrical Requirements."
A sturdy floor to support the total weight (dryer and load) of 200 Ibs (90.7 kg). The
combined weight of a companion appliance should also be considered.
Cold water faucets located within 4 ft (1.2 m) of the water fill valves, and water pressure
of 20-100 psi (138-690 kPa). You may use the water supply for your washer using the "Y"
connector and short hose (if needed) which are provided.
20-100 psi (138-690 kPa) for best performance.
A level floor with a maximum slope of I" (2.5 cm) under entire dryer.
Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer
might not shut off at the end of an automatic cycle. Drying times can be extended.
[he dryer must not be installed or stored in an area where it will be exposed to water and/or
weather.
Check code requirements. Some codes limit, or do not permit, installation of the dryer in
garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.
Installation Clearances
[he location must be large enough to allow the dryer door to open fully.
4
Dryer Dimensions
*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the
exhaust vent with elbow. See "Venting Requirements."
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested
for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be
considered for the following reasons:
Additional spacing should lye considered for ease of installation and servicing.
Additional clearances might be required for wall, door and floor moldings.
Additional spacing should lye considered on all sides of the dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation openings in the top and bottom
of the door are required. [ ouvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also lye considered.
Additional spacing is required if you exhaust out the rear of the dryer to either the right or
left side.
/Z
r' _1 b_ 29"_ I_1" -_lv'*l<25,_"_-I5"
(2.5cm) (2.5crn)
m
_in. 2.
(315cm2i- " _"
24in.2*
(73.7crn) (2.5crn)(74.3ore)(12.7crn)
A B C
__ 3 I'*
(7.6cm)
_ 3"*
(7.6cm)
A. Recessed area
B. Side view - closet or confined area
C. Closet door with wtnts
*Required spacing
Mobile home - Additional installation requirements
This dryer is suitable for mobile home installations. The installation must conform to the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the
Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or
Standard CAN/CSA-Z240 MH.
Mobile home installations require:
Metal exhaust system hardware, which is aw_ilable for purchase from your dealer.
Special provisions must lye made in mobile homes to introduce outside air into the dryer.
[he opening (such as a nearby window) should be at least twice as large as the dryer
exhaust opening.
It is your responsibility
lo contact a qualified electrical installer.
ib be sure that the electrical connection is adequate and in conformance with the
National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and
ordinances.
The National Electric Code requires a 4-wire power supply connection for homes built
after 1996, dryer circuits involved in remodeling after 1996, and all mobile home
installations.
A copy of the above code standards can lye obtained from: National Fire Protection
Association, One Batterymarch Park, Quincy, MA 02269.
1o supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical
supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate)
on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit
breaker is recommended. Connect to an individual branch circuit. [)o not have a fuse in
the neutral or grounding circuit.
1)o not use an extension cord.
If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician determine that the ground path is adequate.
Electrical Connection
[b properly install your dryer, you must determine the type of electrical connection you will
lye using and follow the instructions provided for it here.
[his dryer is manufactured ready to install with a 3-wire electrical supply connection. The
neutral ground conductor is permanently connected to the neutral conductor (white wire)
within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the
neutral ground conductor must be removed from the external ground connector (green
screw), and secured under the neutral terminal (center or white wire) of the terminal
block. When the neutral ground conductor is secured under the neutral terminal (center
or white wire) of the terminal block, the dryer cabinet is isolated from the neutral
conductor.
.... 5
[]
[]
If local codes do not permit the connection of a neutral ground wire to the neutral wire,
see "Optional 3-wire connection" in "Electrical Connection - U.S.A. Only" section.
A 4-wire power supply connection must be used when the appliance is installed in a
location where grounding through the neutral conductor is prohibited. Grounding
through the neutral is prohibited for (I) new branch-circuit installations, (2) mobile
homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding
through the neutral conductors.
If using a power supply cord:
Use a U[. listed power supply cord kit marked for use with clothes dryers. The kit should
contain:
[] A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be
type SR[]) or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer
must end in ring terminals or spade terminals with upturned ends.
[] A UL listed strain relief.
If your outlet looks like this:
4-wire re'ceptacle" (14-30R)
Then choose a 4-wire power supply cord with ring or spade terminals and UI. listed strain
relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge
copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground
conductor) may be either green or [)are. The neutral conductor must be identified by a white
cover.
If your outlet looks like this:
If connecting by direct wire:
Power supply cable must match power supply (4-wire or 3-wire) and be:
[] Flexible armored cable or nonmetallic sheathed copper cable (with ground wire),
protected with flexible metallic conduit. All current-carrying wires must be insulated.
[] 10-gauge solid copper wire (do not use aluminum).
[] At least 5 ft (1.52 m) long.
GROUNDING INSTRUCTIONS
[] For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer uses a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
[] For a permanently connected dryer:
This dryer must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the dryer.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electlic shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug on the power
supply cord: if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
3-wire" re'ceptacle" (lO-30R)
Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain
relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge
copper wires and match a 3-wire receptacle of NEMA t_/pe 10-30R.
6
.... _ _ 51 ....
if you are using a replacement power supply cord, it is recommended that you use Power
Supply Cord Replacement Part Number 3394208. For further information, please reference
the service numbers located in the "Assistance or Service" section.
Electrical Shock Hazard
Plug into a grounded 4 prong outlet.
Failure to do so can result in death or electrical shock.
It is your responsibility
[b contact a qualified electrical installer.
[b be sure that the electrical connection is adequate and in conformance with the
Canadian Electrical Code, C22.1 -latest edition and all local codes. A copy of the above
codes standard may be obtained from: Canadian Standards Association, 178 Rexdale
Blvd., toronto, ON M9W 1R3 CANADA.
[b supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical
supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or
circuit breaker is recommended. Connect to an individual branch circuit
This dryer is equipped with a CSA International Certified Power Cord intended to be
plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be
sure wall receptacle is within reach of dryer's final location.
GROUNDING iNSTRUCTiONS
For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with the
dryer: if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
SAVE THESE INSTRUCTIONS
4-wir_" r_'ceptacle t4-30R
Do not use an extension cord.
Power Supply Cord
Fire Hazard
Use a new UL listed 30 amp power supply cord.
Use a UL listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center
terminal (silver).
Ground wire (green or bare wire) must be connected to
green ground connector.
Connect remaining 2 supply wires to remaining
2 terminals (gold).
Securely tighten all electrical connections.
Failure to do so can result in death, fire, or
electrical shock.
Direct Wire
Fire Hazard
Use 10 gauge solid copper wire.
Use a UL listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center
terminal (silver).
Ground wire (green or bare wire) must be connected to
green ground connector.
Connect remaining 2 supply wires to remaining
2 terminals (gold).
Securely tighten all electrical connections.
Failure to do so can result in death, fire, or
electrical shock.
1. Disconnect power.
2. Remove the hold-down screw and terminal block cover. A B C D
E
F
A. lbrt'Mnal bk)ck cover
B. Exte'rnal ground conductor
5cre'_,v
C. Cc'nte¢; silver-colore'd
terminal block scre'w
D. Hold<town scre'w location
E. Neutral ground wir_"
I. Hole below tert:'linal block
opening
8
3. Install strain relief.
Style 1: Power supply cord strain relief
Remove the screws from a 3/4"(1.9 cm) UI. listed strain relief (U[ marking on strain relief).
Put the tabs of the two clamp sections into the hole below the terminal block opening so
that one tab is pointing up and the other is pointing down, and hold in place. Tighten
strain relief screws just enough to hold the two clamp sections togethen
A. Strain rt'lief tab pointing up
8. Hole below terminal block opening
C. Clamp section
D. Strain relief tab pointing down
Put power supply cord through the strain relief. Be sure that the wire insulation on the
power supply cord is inside the strain relief. The strain relief should have a tight fit with
the dryer cabinet and be in a horizontal position. Do not further tighten strain relief
screws at this point.
Style 2: Direct wire strain relief
Unscrew the removable conduit connector and any screws from a 3/4"(1.9 cm) U]. listed
strain relief (UI. marking on strain relief). Put the threaded section of the strain relief
through the hole below the terminal block opening. Reaching inside the terminal block
opening, screw the removable conduit connector onto the strain relief threads.
......................... B
...... C
A. Removable conduit connector
B. Hole below terminal block opening
C. Strain relief thread_
Put direct wire cable through the strain relief. The strain relief should have a tight fit with
the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the
direct wire cable.
Now complete installation following instructions for your type of electrical connection:
4-wire/recommended)
3-wire (if 4-wire is not available
.... 9
Electrical Connection Options
If your home has: And you will be Go to Section:
connecting to:
4-wire receptacle A UL listed, 4-wire connection:
(NEMA type 14-30R) 120/240-volt minimum, Power Supply Cord
__._._ 30-amp, dryer power
supply cord*
4-wire direct A fused disconnect or 4-wire connection:
circuit breaker box* Direct Wire
(12.7 cm)
3-wire receptacle
(NEMA type 10-30R)
©
3-wire direct
A U[. listed,
120/240-volt minimum,
30-amp, dryer power
supply cord*
A fused disconnect or
circuit breaker box*
3-wire connection:
Power Supply Cord
3-wire connection:
Direct Wire
*If local codes do not permit the connection of a cabinet-ground conductor to the neutral
wire, go to "Optional 3-wire connection" section.
4-wire connection: Power supply cord
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do
not permit the use of 3-wire connections.
B F
C D E G
A. 4-wire receptacle" (NEMiA type 14-30R)
B. 4-prong plug
C. Ground prong
D. Neubal prong
E. Spade tenTfinals with upturned end_
L ?_" ( 1.9 cm) U_ li_ted strain relief
C. Ring terminals
Remove center silver-colored terminal block screw.
2_
Remove neutral ground wire from external ground conductor screw. Connect neutral
ground wire and the neutral wire (white or center wire) of power supply cord under
center, silver-colored terminal block screw. Tighten screw.
D
3_
A. Neutral ground wire
B. Fxternal ground conductor screw - Dotted line shows position
of NEUTRAL ground wire before being moved to centaur silw_r-
colored terminal block screw.
C. C_'nter silver-colored te'rminal block screw
D. Neutral wire" (white or center wire)
E. _" (1.9 cm) tJt listed strain relief
Connect ground wire/green or bare) of power supply cord to external ground conductor
screw. Tighten screw.
A. £xternal glound conductor scren,v
B. Neutral ground wire
C. Ground wire (green or bare) of power supply cord
D. Y#" ( 1.9 cm) U[ listed strain relief
E. Center silver-colored terminal block scr_w
L Ne_utral wire (white or center wire)
1O
4. Connecttheotherwirestoouterterminalblockscrews.Tightenscrews.
!! !!
5. Tighten strain relief screws.
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-
down screw,
7. You have completed your electrical connection. Now go to "Venting Requirements."
4-wire connection: Direct Wire
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do
not permit the use of 3 wire connections.
Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.
Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5"
(12.7 cm). Cut 11A" (3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm). Shape
ends of wires into a hook shape.
A. Neutral ground wire
B. External ground conductor screw - Dotted line shows
position of NEUTRAL ground wire before' being moved to
center silver-colored tenTfinal block screw.
C. Center silver-colored ten'ninal block screw
D. Neutral wire' (white or center wire)
E. Y4" ( 1.9 cm) UL listed strain relief
Connect ground wire/green or bare) of direct wire cable to external ground conductor
screw. Tighten screw.
When connecting to the terminal block, place the hooked end of the wire under the screw of
the terminal block (hook facing right), squeeze hooked end together and tighten screw, as
shown.
2.
Remove center silver-colored terminal block screw.
Remove neutral ground wire from external ground conductor screw. Connect neutral
ground wire and place the hooked end (hook facing right) of the neutral wire (white or
center wire) of direct wire cable under the center screw of the terminal block. Squeeze
hooked ends together. Tighten screw.
A. Lxternal ground conductor screw
B. Neutral ground wire
C. Ground wire (green or bare) of power supply cord
D. ¾" ( 1.9 cm) UL listed strain relief
E. C_'nter silver-colored terminal block screw
L Neutral wire (white or center wire)
4. Place the hooked ends of the other direct wire cable wires under the outer terminal block 2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-
screws (hooks facing right). Squeeze hooked ends together. Tighten screws, colored terminal screw of the terminal block. Tighten screw.
!! !!
5. Tighten strain relief screw.
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-
down screw.
7. You have completed your electrical connection. Now go to "Venting Requirements."
3-wire connection: Power supply cord
Use where local codes permit connecting cabinet-ground conductor to neutral wire.
A ........ / ' I
C G F
1,
A. 3-wire receptacle (NEMA type IO-30R)
B. 3-wire plug
C. Neutral prong
D. Spade terminah with upturned ends
E. _" ( 1.9 cm) Ut listed strain relief
f. Ring term[nab
G. Neutral wire (white or center wire)
Loosen or remove center silver-colored terminal [)lock screw.
3,
A. External ground colTductol screw
B. Neutral ground wire
C. Center silver-colored terminal block screw
D. Neutral wire (white or center wire)
E. _" t 1.9 cm) U_ listed strain relief
Connect the other wires to outer terminal [)lock screws. Tighten screws.
I! !!
4. Tighten strain relief screws.
5. Insert tab of terminal block cover into slot of dryer rear paneh Secure cover with hold-
down screw.
6. You have completed your electrical connection. Now go to "Venting Requirements."
12
3-wire connection: Direct Wire
Use where local codes permit connecting cabinet-ground conductor to neutral wire.
Direct wire cable must have 5 ft (1.52 rn) of extra length so dryer can be moved if needed.
Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If
using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of
wires into a hook shape.
t"
_B.9 co)
When connecting to the terminal block, place the hooked end of time wire under the screw of
the terminal block (hook facing right), squeeze hooked end together and tighten screw, as
shown.
1,
2.
koosen or remove center silver-colored terminal block screw.
Place the hooked end of the neutral wire (white or center wire) of direct wire cable under
the center screw of terminal block (hook facing right). Squeeze hooked end together.
Tighten screw.
-t
A. [xternal ground conductor screw
B. Neutral ground wir_"
C. Ce'nter silver-colore'd terminal block scr_'vv
D. Neutral wire (white" or center wire')
E. _" (1.9 cm) UL list_'d strain r_qi_f
Place the hooked ends of the other direct wire cable wires under timeouter terminal block
screws (hooks facing right). Squeeze hooked ends together. Tighten screws.
!! !!
4. Tighten strain relief screw.
5. Insert tab of terminal block cover into slot of dryer rear paneh Secure cover with hold-
down screw.
6. You have completed your electrical connection. Now go to "Venting Requirements."
Optional 3-wire connection
Use for direct wire or power supply cord where local codes do not permit connecting
cabinet-ground conductor to neutral wire.
1. Remove center silver-colored terminal block screw.
2. Remove neutral ground wire from external ground conductor screw. Connect neutral
ground wire and the neutral wire (white or center wire) of power supply cord/_ able under
center, silver-colored terminal block screw. Tighten screw.
A. Exte'rnal g,round conductor screw
B. Neutral ground wire'
C. C_'nter silv_'r-color_'d terminal block screw
D. Neutral wire (white or center wire')
E. _" ( 1.9 cm) UL listed strain relief
f. Crouncfing path determined by a qualifie'd electrician
3. Connect the other wires to outer terminal block screws. Tighten screws.
!! !!
4. Tighten strain relief screws.
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-
down screw.
6. Connect a separate copper ground wire from the external ground conductor screw to an
adequate ground.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
WARNING: Io reduce the risk of fire, this dryer MUSF BE EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a
concealed space of a building.
If using an existing vent system
Clean lint from the entire length of the system and make sure exhaust hood is not plugged
with lint.
Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.
Review Vent system chart. Modify existing vent system if necessary to achieve the best
drying performance.
If this is a new vent system
Vent material
Use a heavy metal vent. Do not use plastic or metal foil vent,
4" (10,2 cm) heavy metal exhaust vent and clamps must be used.
4" ( 10.2 cm) heavy metal _'xhaust vent
Vent products can be purchased from your dealer or by calling Maytag Services. For more
information, see the "Assistance or Service" section.
Rigid metal vent
For best drying performance, rigid metal vents are recommended.
Rigid metal vent is recommended to avoid crushing and kinking.
Flexible metal vent
Flexible metal vents are acceptable only if accessible for cleaning.
Flexible metal vent must be fully extended and supported when the dryer is in its final
location.
Remove excess flexible metal vent to avoid sagging and kinking that may result in
reduced airflow and poor performance.
Do not install flexible metal vent in enclosed walls, ceilings or floors.
Elbows
45 ° elbows provide better airflow than 90 ° elbows.
Clamps
Good Better
Use clamps to seal all joints.
14
Exhaust
Exhaustventmustnotbeconnectedorsecuredwithscrewsorotherfasteningdevices
thatextendintotheinterioroftheduct.Donotuseducttape.
ii C
Clamp
Recommended hood styles are shown here.
B
(10.2 cm)
A. Louw'r_'d hood styli"
B.Box hood style
The angled hood style {shown here) is acceptable.
4"
(10.2 cm)_
An exhaust hood should cap the vent to keep rodents and insects from entering the home.
Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in
the path of the exhaust {such as flowers, rocks or bushes, snow line, etc.).
Do not use an exhaust hood with a magnetic latch.
improper venting can cause moisture and lint to collect
indoors, which may result m:
[] Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
[] Housecleaning problems and health problems.
D ............_ .... "' -
Choose your exhaust installation type
Recommended exhaust installations
[ypical installations vent the dryer from the rear of the dryer.
B
i
A--
A. Dryer
B. Dbow
C. Wall
D. Fxhaust hood
IIII
J ll B
E.Clamps
[. Rigid rnetal or fle'xible metal vent
G. V_'nt letlgth necessary to connect elbows
H. _xhaust outlet
Standard exhaust installation with rigid metal or flexible metal vent
Alternate installations for close clearances
Venting systems come ill many varieties. Select the type best for your installation. Two close-
clearance installations are shown. Refer to the manufacturer's instructions.
A B C
A. Over-the-top installation (also available" with one offset elbow)
B.Periscope installation
C. Rear exhaust installation to left or right side
NOTE: The following kits for close clearance alternate installations are available for purchase.
Please see the "Assistance or Service" section to order.
Over-the-Top Installation:
Part Number 4"¢96028
Periscope Installation (For use with dryer vent to wall vent mismatch):
Part Number 43960"¢7 - 0" (0 cm) to 18" (45.72 cm) mismatch
Part Number 4396011 - 18" (45.72 cm) to 29" (7"X66 cm) mismatch
Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch
Rear exhaust installation to left or right side:
Part Number 4"¢96011
Vent extension:
Part Number 8544761
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible portion of the mobile home
structure and must not terminate beneath the mobile home. [erminate the exhaust vent
outside.
/
Determine vent path
Select the route that will provide the straightest and most direct path outdoors.
Plan the installation to use the fewest number of elbows and turns.
When using elbows or making turns, allow as much room as possible.
Bend vent gradually to avoid kinking.
Use the fewest 90 ° turns possible.
Determine vent length and elbows needed for best drying performance
Use the following Vent system chart to determine type of vent material and hood
combinations acceptable to use.
NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust
systems longer than those specified will:
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and increased energy usage.
[he Vent system chart provides venting requirements that will help to achieve the best drying
performance.
Vent system chart
NOTE: Performance of rear exhaust to either side of the dryer is equiw_lent to adding one
elbow. lb determine maximum exhaust length, add one elbow to the chart.
Number of Type of Box or Angled
90 ° turns vent Louvered hoods
or elbows hoods
0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)
Flexible metal 36 ft (11 m) 28 ft/8.5 m)
.............................................................................................................................................................................................................................
1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)
Flexible metal 31 ft (9.4 m) 23 ft 17 m)
.............................................................................................................................................................................................................................
2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)
Flexible metal 27 ft (8.2 m) I9 ft 15.8 m)
.............................................................................................................................................................................................................................
3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)
Flexible metal 25 ft 17.6 m) 17 ft/5.2 m)
.............................................................................................................................................................................................................................
4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)
Flexible metal 23 ft (7 m) 15 ft (4.6 m)
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around
exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust
hood with 4" (10.2 cm) clamp.
3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in
"Plan Vent System." Avoid 90 ° turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior of the vent to secure vent.
16
1,
2.
Le s
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
[b protect the floor, use a large, flat piece of cardboard from the dryer carton. Place
cardboard under the entire back edge of the dryer.
Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on
the cardboard. See illustration.
The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use
old hoses.
l. Turn cold water faucet off and remove washer inlet hose.
2. Remove old rubber washer from inlet hose and replace with new rubber washer provided.
If space permits, attach the brass female end of the "Y" connector to the cold water faucet.
NOTE: If "Y" connector can be attached directly to cold water faucet, go to Step 6. If "Y"
connector cannot be attached directly to the cold water faucet, the short hose must be
used. Continue with Step 3.
3. Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on
faucet.
4. Using pliers, tighten the couplings with an additional two-thirds turn.
Examine the leveling legs. Find the diamond marking.
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the
diamond marking is no longer visible.
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.
Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.
leave enough room to connect the exhaust vent.
1. Using a 4_ (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to
existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust
outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a
4" (10.2 cm) clamp.
2. Move dryer into its final location. Do not crush or kink vent.
3. (On gas models) Check that there are no kinks in the flexible gas line.
4. Once the exhaust vent connection is made, remove the corner posts and cardboard.
NOTE: Do not overtighten. Damage to the coupling can result.
5. Attach "Y" connector to brass male end of small hose. Screw on coupling by hand until it
is seated on connector.
6. Attach straight end of long hose to "Y" connector.
7. Attach washer cold inlet hose to other end of "Y" connector. Screw on coupling by hand
until it is seated on connector.
8. Using pliers, tighten the couplings with an additional two-thirds turn.
9.
A. Inlet to cold water
NOTE: Do not overtighten. Damage to the coupling can result.
Attach angled end of long hose to fill valve at bottom of dryer back panel Screw on
coupling by hand until it is seated on fill valve connector.
!_;rill_i_!_!!iii!iiii_ii!!iiiiiiiiiiiiiiiiiiii_!!_!_i_!_!_!_!i;ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_iiI i_iii!iii!ii!ii!ii%i!! 17
10. Using pliers, tighten the coupling with an additional two-thirds turn. If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs
up or down and check again for levelness.
NOIE: Do not overtighten. Damage to the coupling can result.
11. Check that the water faucets are on.
12. Check for leaks around "Y" connector, faucet and hoses.
Check the levelness of the dryer by first placing a level on the top of the dryer near the
conso[e.
You can change your door swing from a right-side opening to a left-side opening, if desired.
1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.
Remove the door assembly
1. Open the dryer door.
2. Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front
panel of the dryer.
3. [oosen the top screw from each of the 2 hinges in Step 2.
]hen, by placing a level in the crease on the side of the dryer between the top of the dryer and
the dryer cabinet, check the levelness from front to back.
4,
A
'B
A. _oose'll the'se' 5creq,vs.
_. Remove" these" scre\,vg.
Remove the dryer door and the hinges by lifting upward on the door. I.ay the door on a
flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose
screws from dryer front panel.
18
5. Remove the 4 plastic plugs located outside the dryer door opening.
6. Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in
Step 4.
Reverse the strike
1. Remove the door strike from the dryer door opening.
2. Remove the cosmetic screw opposite the door strike.
A. Door strike
B. Cbsmetic screw
Reinstall the door strike and cosmetic screw on the opposite side of the dryer door
opening from where they were removed.
NOTE: Door strike and plugs must be on the same side of the dryer door opening.
Reinstall the door
1. Remove the 4 screws and 2 hinges from the dryer door.
2. Replace the 4 screws in the same holes.
_ " _"
3. Remove the 4 screws from the opposite side of the door.
I
I
..a
Install tile 2 hinges to the front panel of the dryer using 4 screws. Use tile non-slotted side
to attach the hinge to the front panel.
5.
6.
Install screws in the top hinge holes in the door. Do not tighten screws. Heave
approximately Y2' (5 mm) of screw exposed.
A. Install these screws first.
Hang door by placing screw heads into top slotted holes of hinges and slide door down.
Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge
screws,
1
7. Close door to engage door strike.
1. Check that all parts are now installed. If there is an extra part, go back through the steps to
see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Be sure the water faucets are on.
5. Check for leaks around "Y" connector, faucet and hoses.
6. Check the dryer's final location. Be sure the vent is not crushed or kinked.
7. Check that the dryer is level. See "l.evel Dryer."
8. In the U.S.A.
For power supply cord installation, plug into a grounded outlet. For direct wire
installation, turn on power.
In Canada
Plug into a grounded 4 prong outlet. lurn on power.
9. Remove any protective film or tape remaining on the dryer.
NOTE: Glass door models have a protective film on the window that should be removed.
10. Read "Dryer Use."
11. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.
12. If you live in a hard water area, use of a water softener is recommended to control the
buildup of scale through the water system in the dryer. Over time, the buildup of lime
scale may clog different parts of the water system, which will reduce product
performance. Excessive scale builclup may lead to the need for certain [)art replacement
or repair.
13. ]i_st dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this
test, do not select the Air Fluff modifier.
If the dryer will not start, check the following:
Controls are set in a running or "On" position.
Start button has been pushed firmly.
Dryer is plugged into an outlet and/or electrical supply
is on.
Household fuse is intact and tight, or circuit breaker has not tripped.
Dryer door is closed.
[his dryer automatically runs an installation diagnostic routine at the start of its first cycle.
If you receive an "L2" code, there may be a problem with your home power supply keeping
the dryer's heater from turning on. See "Troubleshooting."
If you receive an "AF" code, your dryer vent may be crushed or blocked. See
"Troubleshooting."
NOTE: You may notice a burning odor when the dryer is first heated. [his odor is common
when the heating element is first used. The odor will go away.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Maytag MED6600TQ - 27 Inch Electric Washer Manuel utilisateur

Catégorie
Laveuses sécheuses
Taper
Manuel utilisateur