Troy-Bilt 31BH5DR7563 Mode d'emploi

Marque: Troy-Bilt

Modèle: 31BH5DR7563

Catégorie: Souffleuses à neige

Taper: Mode d'emploi

Ce manuel convient également à

Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

OperatOr’s Manual

Form No. 769-11740B

(May 22, 2018)

Safe Operation Practices ........................................ 2

Assembly & Set-Up .................................................. 5

Controls & Operation .............................................16

Product Care ...........................................................21

Parts/Warranty .............. See Separate Supplement

French ..................................................................... 25

Table of Contents

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable

to all models and the model depicted may differ from yours. The terms “snow blower” and “snow thrower” may be used

interchangeably for this product.

Snow Blower

2-Stage and 3-Stage

500 & 800 Series - Models with steering trigger controls.

600 Series - Models without steering trigger controls

Important Safe Operation Practices

WARNING!

This symbol points out important safety

instructions which, if not followed, could

endanger the personal safety and/or property

of yourself and others. Read and follow all

instructions in this manual before attempting

to operate the equipment. Failure to comply

with these instructions may result in personal

injury. When you see this symbol. HEED ITS

WARNING!

CALIFORNIA PROPOSITION 65

Engine Exhaust, some of its constituents, and

certain vehicle components contain or emit

chemicals known to State of California to cause

cancer and birth defects or other reproductive

harm.

DANGER!

This machine was built to be operated according to

the safe operation practices in this manual. As with

any type of power equipment, carelessness or error

on the part of the operator can result in serious injury.

This machine is capable of amputating fingers, hands,

toes and feet and throwing foreign objects. Failure to

observe the following safety instructions could result

in serious injury or death.

NOTE: The terms “snow blower” and “snow

thrower” may be used interchangeably for this

product.

Training

1. Read, understand, and follow all

instructions on the machine and in

the manual(s) before attempting to

assemble and operate. Keep this manual

in a safe place for future and regular

reference and for ordering replacement

parts.

2. Be familiar with all controls and their

proper operation. Know how to stop the

machine and disengage them quickly.

3. Never allow children under 14 years of

age to operate this machine. Children 14

and over should read and understand

the instructions and safe operation

practices in this manual and on the

machine and be trained and supervised

by an adult.

4. Never allow adults to operate this

machine without proper instruction.

5. Thrown objects can cause serious

personal injury. Plan your snow-

throwing pattern to avoid discharge of

material toward roads, bystanders and

the like.

6. Keep bystanders, pets and children at

least 75 feet from the machine while it

is in operation. Stop machine if anyone

enters the area.

7. Exercise caution to avoid slipping or

falling, especially when operating in

reverse.

Preparation

Thoroughly inspect the area where the

equipment is to be used. Remove all doormats,

newspapers, sleds, boards, wires and other

foreign objects, which could be tripped over or

thrown by the auger.

1. Always wear safety glasses or eye shields

during operation and while performing

an adjustment or repair to protect your

eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

2. Do not operate without wearing

adequate winter outer garments. Do

not wear jewelry, long scarves or other

loose clothing, which could become

entangled in moving parts. Wear

footwear which will improve footing on

slippery surfaces.

3. Use a grounded three-wire extension

cord and receptacle for all machines

with electric start engines.

4. Adjust auger housing height to clear

gravel or crushed rock surfaces.

5. Disengage all control levers before

starting the engine.

6. Never attempt to make any adjustments

while engine is running, except where

specifically recommended in the

operator’s manual.

7. Let engine and machine adjust to

outdoor temperature before starting to

clear snow.

Safe Handling of Gasoline

To avoid personal injury or property damage

use extreme care in handling gasoline.

Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury

can occur when gasoline is spilled on yourself

or your clothes which can ignite. Wash your

skin and change clothes immediately.

1. Use only an approved gasoline

container.

2. Extinguish all cigarettes, cigars, pipes

and other sources of ignition.

3. Never fuel machine indoors.

4. Never remove gas cap or add fuel while

the engine is hot or running.

5. Allow engine to cool at least two

minutes before refueling.

6. Never over fill fuel tank. Fill tank to

no more than ½ inch below bottom

of filler neck to provide space for fuel

expansion.

7. Replace gasoline cap and tighten

securely.

8. If gasoline is spilled, wipe it off the

engine and equipment. Move machine

to another area. Wait 5 minutes before

starting the engine. If fuel is spilled on

clothing, change clothing immediately.

9. Never store the machine or fuel

container inside where there is an open

flame, spark or pilot light (e.g. furnace,

water heater, space heater, clothes dryer

etc.).

10. Allow machine to cool at least 5 minutes

before storing.

11. Never fill containers inside a vehicle or

on a truck or trailer bed with a plastic

liner. Always place containers on the

ground away from your vehicle before

filling.

12. If possible, remove gas-powered

equipment from the truck or trailer and

refuel it on the ground. If this is not

possible, then refuel such equipment on

a trailer with a portable container, rather

than from a gasoline dispenser nozzle.

13. Keep the nozzle in contact with the rim

of the fuel tank or container opening at

all times until fueling is complete. Do

not use a nozzle lock-open device.

Operation

1. Do not put hands or feet near rotating

parts, in the auger housing or chute

assembly. Contact with the rotating

parts can amputate hands and feet.

2. The auger control lever is a safety

device. Never bypass its operation.

Doing so makes the machine unsafe and

may cause personal injury.

3. The control levers must operate easily

in both directions and automatically

return to the disengaged position when

released.

4. Never operate with a missing or

damaged chute assembly. Keep all

safety devices in place and working.

5. Never run an engine indoors or in a

poorly ventilated area. Engine exhaust

contains carbon monoxide, an odorless

and deadly gas.

3Section 1 — important Safe operation practiceS

6. Do not operate machine while under

the influence of alcohol or drugs.

7. Muffler and engine become hot and

can cause a burn. Do not touch. Keep

children away.

8. Exercise extreme caution when

operating on or crossing gravel surfaces.

Stay alert for hidden hazards or traffic.

9. Exercise caution when changing

direction and while operating on slopes.

Do not operate on steep slopes.

10. Plan your snow-throwing pattern to

avoid discharge towards windows,

walls, cars etc. Thus, avoiding possible

property damage or personal injury

caused by a ricochet.

11. Never direct discharge at children,

bystanders and pets or allow anyone in

front of the machine.

12. Do not overload machine capacity by

attempting to clear snow at too fast of

a rate.

13. Never operate this machine without

good visibility or light. Always be sure of

your footing and keep a firm hold on the

handles. Walk, never run.

14. Release auger control lever to disengage

power to the auger when transporting

or not clearing snow.

15. Never operate machine at high

transport speeds on slippery surfaces.

Look down and behind and use care

when backing up.

16. After striking a foreign object or if

the machine should start to vibrate

abnormally, stop the engine, disconnect

the spark plug wire and ground it

against the engine. Inspect thoroughly

for damage. Repair any damage before

starting and operating.

17. Disengage all control levers and stop

engine before you leave the operating

position (behind the handles). Wait until

the auger comes to a complete stop

before unclogging the chute assembly,

making any adjustments, or inspections.

18. Never put your hand in the discharge

or collector openings. Always use the

clean-out tool provided to unclog the

discharge opening. Do not unclog chute

assembly while engine is running. Shut

off engine and remain behind handles

until all moving parts have stopped

before unclogging.

19. Use only attachments and accessories

approved by the manufacturer (e.g.

wheel weights, tire chains, cabs etc.).

20. When starting engine, pull cord

slowly until resistance is felt, then pull

rapidly. Rapid retraction of starter

cord (kickback) will pull hand and arm

toward engine faster than you can let

go. Broken bones, fractures, bruises or

sprains could result.

21. If situations occur which are not covered

in this manual, use care and good

judgment. Contact Customer Support

for assistance and the name of your

nearest servicing dealer.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside

the discharge chute is the most common

cause of injury associated with snow throwers.

Never use your hand to clean out the discharge

chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the impeller

blades have stopped rotating.

3. Always use a clean-out tool, not your

hands.

Maintenance & Storage

1. Never tamper with safety devices. Check

their proper operation regularly. Refer

to the maintenance and adjustment

sections of this manual.

2. Before cleaning, repairing, or inspecting

machine disengage all control levers

and stop the engine. Wait until the

auger come to a complete stop.

Disconnect the spark plug wire and

ground against the engine to prevent

unintended starting.

3. Check bolts and screws for proper

tightness at frequent intervals to keep

the machine in safe working condition.

Also, visually inspect machine for any

damage.

4. Do not change the engine governor

setting or over-speed the engine. The

governor controls the maximum safe

operating speed of the engine.

5. Snow thrower shave plates and skid

shoes are subject to wear and damage.

For your safety protection, frequently

check all components and replace with

original equipment manufacturer’s

(OEM) parts only. “Use of parts which

do not meet the original equipment

specifications may lead to improper

performance and compromise safety!”

6. Check control levers periodically to

verify they engage and disengage

properly and adjust, if necessary.

Refer to the adjustment section in this

operator’s manual for instructions.

7. Maintain or replace safety and

instruction labels, as necessary.

8. Observe proper disposal laws and

regulations for gas, oil, etc. to protect

the environment.

9. Prior to storing, run machine a few

minutes to clear snow from machine

and prevent freeze up of auger.

10. Never store the machine or fuel

container inside where there is an open

flame, spark or pilot light such as a water

heater, furnace, clothes dryer, etc.

11. Always refer to the operator’s manual

for proper instructions on off-season

storage.

12. Check fuel line, tank, cap, and fittings

frequently for cracks or leaks. Replace if

necessary.

13. Do not crank engine with spark plug

removed.

14. According to the Consumer Products

Safety Commission (CPSC) and the U.S.

Environmental Protection Agency (EPA),

this product has an Average Useful Life of

seven (7) years, or 60 hours of operation.

At the end of the Average Useful Life

have the machine inspected annually by

an authorized service dealer to ensure

that all mechanical and safety systems

are working properly and not worn

excessively. Failure to do so can result in

accidents, injuries or death.

Do not modify engine

To avoid serious injury or death, do not

modify engine in any way. Tampering with the

governor setting can lead to a runaway engine

and cause it to operate at unsafe speeds.

Never tamper with factory setting of engine

governor.

Notice Regarding Emissions

Engines which are certified to comply with

California and federal EPA emission regulations

for SORE (Small Off Road Equipment) are

certified to operate on regular unleaded

gasoline, and may include the following

emission control systems: Engine Modification

(EM), Oxidizing Catalyst (OC), Secondary Air

Injection (SAI) and Three Way Catalyst (TWC) if

so equipped.

4 Section 1 — important Safe operation practiceS

Safety Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before

attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to assemble and

operate.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running. There are rotating

blades inside.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running. There are rotating

blades inside.

WARNING— ROTATING AUGER

Do not put hands or feet near rotating parts, in the auger housing or chute assembly. Contact

with the rotating parts can amputate hands and feet.

WARNING—THROWN OBJECTS

This machine may pick up and throw objects which can cause serious personal injury.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon

monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain.

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine and

muffler to cool before touching.

WARNING! - SAVE THESE INSTRUCTIONS

Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the

machine.

Assembly & Set-Up

Thank you for purchasing this product. It was carefully engineered to

provide excellent performance when properly operated and maintained.

Please read this entire manual prior to operating the equipment. It

instructs you how to safely and easily set up, operate and maintain your

machine. Please be sure that you, and any other persons who will operate

the machine, carefully follow the recommended safety practices at all

times. Failure to do so could result in personal injury or property damage.

All information in this manual is relative to the most recent product

information available at the time of printing. Review this manual frequently

to familiarize yourself with the machine, its features and operation. Please

be aware that this Operator’s Manual may cover a range of product

specifications for various models. Characteristics and features discussed

and/or illustrated in this manual may not be applicable to all models. The

manufacture reserves the right to change product specifications, designs

and equipment without notice and without incurring obligation.

The engine manufacturer is responsible for all engine-related issues with

regards to performance, power-rating, specifications, warranty and service.

Please refer to the engine manufacturer’s Owner’s/Operator’s Manual,

packed separately with your machine, for more information.

If you have any problems or questions concerning the machine, phone your

local authorized service dealer or contact us directly. We want to ensure

your complete satisfaction at all times.

Throughout this manual, all references to right and left side of the machine

are observed from the operating position.

Thank You

Contents of Carton

• Snow Blower (1) • Snow Blower Operator’s Manual (1) • Skid Shoe Kit*

• Chute Assembly (1) • Engine Operator’s Manual (1) Short Carriage Screw (4)

• Chute Control Rod, Flex Shaft, or Side • Parts/Warranty Document (1) Flat Washer (4, if required)

Crank Rod Assembly* (1) • Handle Hardware Flange Lock Nut (4)

• Replacement Auger Shear Pins (2) Long Carriage Screw* (2)

• Safety Key (2) Flange Lock Nut* (2) * If Equipped

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all models and the

model depicted may differ from yours. Refer to Figure 2-7 which shows the different versions and match the contents of carton (chute and directional

control rod/flex shaft) to identify your specific unit.

Overview

• Remove packaging materials from snow

blower.

• Rotate Handle into the upright position.

Refer to Handle Assembly.

• Install the chute. Refer to Chute

Assembly Options.

• Complete snow blower assembly

according to model and equipment.

Refer to Set-up.

• If necessary make adjustments to ensure

proper snow blower operation. Refer to

Adjustments.

• Add fuel and oil. Refer to the Engine

Operator’s Manual shipped with snow

blower.

Tools Required

• Adjustable Wrench or Socket Set

• Needle Nose Pliers

Handle Assembly

1. Cut cable ties securing chute control rod

or upper handle to the lower handle (if

applicable), set aside the chute control

rod (if applicable).

NOTE: If your unit is equipped with a

cable tie securing the control cables to

the engine do not cut the cable tie.

NOTE: On units with Overhead Chute

Control (with Flex Shaft), Four-Way Chute

Control, and Electric Chute Control

cut cable ties securing flex shaft to the

lower handle and set the flex shaft aside.

Remove rubber bands securing cables to

carriage screws and cut cable tie securing

shift rod to lower handle. Refer to Figure

2-7 to help identify your unit.

2. Loosen the top two nuts (a) securing the

upper and lower handle and remove the

two carriage screws (b) from the upper

handle and set aside as shown in Figure

2-1 or Figure 2-2 for units with side

supports.

(a)

(b)

Figure 2-1

(a)

(b)

Figure 2-2

6 Section 2 — ASSembly & Set-Up

Chute Assembly Options

Refer to Figure 2-7 and proceed to your applicable Chute Control Style on pages 7-11.

Overhead Chute Control

(w/ Flex Shaft Steel Chute) Page 10

Electric Chute Control

Pages 11

Chute

Assembly

Chute

Assembly

Flex

Shaft

2-Way & 4-Way Chute Control

Page 9

Overhead Chute Control

(w/ Chute Control Rod) Page 8

Standard Side Crank Chute Control

Page 7

Standard Side Crank

Rod Assembly

Overhead Chute

Control Rod

Chute Control

Rod

Chute

Assembly

Chute

Assembly

Chute

Assembly

Chute Control

Rods

Figure 2-7

(c)

(b)

(a)

Figure 2-5

(c)

(a)

(b)

Figure 2-6

STOP

Refer to “Figure 2-7” on page 6 to identify your

applicable chute style and continue to Chute Assembly

Options (page 6).

3. Place shift lever in Forward-6 position or

fastest forward speed (if equipped).

4. Observe lower rear area of equipment

to be sure both cables (if equipped) are

aligned and seated properly in roller

guides. See Figure 2-3.

NOTE: On select units, chute-pitch control

cables will be routed under the engine on the

left side and will not use roller guides.

Figure 2-3

5. Pivot handle upward and align the lower

handle. See Figure 2-4. Remove and

discard any rubber bands, if present.

They are for packaging purposes only.

Figure 2-4

NOTE: On select units with steel rod

speed selectors, you may need to lower

shift rod to the side slightly to maneuver

handle panel over it when pivoting

handle upward.

6. Attach the two carriage screws (b)

and nuts (a) removed in Step 2. Finish

securing the handle by tightening the

top two nuts (c) loosened in Step 2. See

Figure 2-5 or Figure 2-6 for units with

side supports.

7Section 2 — ASSembly & Set-Up

Standard Side Crank Chute

Control

Standard Side Crank

Rod

Chute Assembly

Figure 2-8

1. Position chute assembly over base.

See Figure 2-9.

Figure 2-9

2. Close flange keepers to secure chute

assembly to chute base. Flange keepers

will click into place when properly

secured. See Figure 2-10.

Figure 2-10

NOTE: Ensure the lower chute is secured to

the flange on the chute base. The lower edge

of the chute keeper should be positioned

below the flange on the chute base after being

clicked into place.

If flange keepers will not

easily click into place, use palm of your hand to

apply swift, firm pressure to the back of each.

3. Remove plastic cap (if present), flat

washer (a) and hairpin clip (b) from end

of chute directional control assembly.

See Figure 2-11.

(b)

(a)

Figure 2-11

4. Insert end of chute directional control

assembly into lower bracket and secure

chute directional control assembly

with flat washer (a) and hairpin clip (b)

removed in Step 1. If necessary, lower

bracket can be adjusted. Refer to Chute

Bracket Adjustment in Service section

on page 23.

STOP

Continue to Set-Up (page 12).

8 Section 2 — ASSembly & Set-Up

2. Place chute assembly onto chute base

and secure chute control head to chute

support bracket with clevis pin (c) and

cotter pin (d) removed in Step 1.

See Figure 2-14.

(c)

(d)

Figure 2-14

3. Finish securing chute control head to

chute support bracket with wing

nut (a) and hex screw (b) removed in

Step 1. See Figure 2-15.

(a)

(b)

Figure 2-15

4. Insert chute control rod into the support

bracket on rear of the dash panel. See

Figure 2-16.

Figure 2-16

5. Remove hairpin clip (a) from rear of

chute control head. See Figure 2-17.

(a)

(b)

Figure 2-17

6. Insert chute control rod (b) into rear

of chute control head. See Figure 2-17.

Secure chute control rod to chute

control assembly with hairpin clip (a)

removed in Step 5.

STOP

Continue to Set-Up (page 12).

Overhead Chute Control (w/

Chute Control Rod)

Overhead Chute

Control Rod

Chute Assembly

Figure 2-12

1. Remove wing nut (a) and hex

screw (b) from chute control head and

clevis pin (c) and cotter pin (d) from

chute support bracket. Position chute

assembly (forward-facing) over chute

base. See Figure 2-13.

(a)

(b)

(c)

(d)

Chute

Support

Bracket

Chute Control

Head

Chute

Chute Base

Figure 2-13

9Section 2 — ASSembly & Set-Up

2-Way & 4-Way Chute Control

Chute Control

Rod

Chute Assembly

Figure 2-18

1. Remove hairpin clip (a), wing nut (b) and

hex screw (c) from chute control head

and clevis pin (d) and bow-tie cotter pin

(e) from chute support bracket.

See Figure 2-19.

(a)

(c)

Chute Control Head

Chute

Support

Bracket

Chute Base

(e)

(d)

(b)

Figure 2-19

NOTE: For smoothest operation, cables should

all be to the left of the chute directional

control rod.

2. Insert round end of the chute control

rod (hole pointing upward) as far as

possible into chute control assembly.

See Figure 2-20.

Figure 2-20

3. Place chute onto chute base and ensure

chute control rod is positioned under

handle panel. Install hex screw (c)

removed in Step 1, but do not secure with

wing nut at this time. See Figure 2-21.

(c)

Figure 2-21

4. Squeeze trigger on joystick and rotate

chute by hand to face forward. The holes

in chute control input will be facing up.

See Figure 2-22.

Chute Control Input

Top View

Joystick

Figure 2-22

NOTE: Chute will not rotate without

squeezing trigger on joystick.

5. Rotate joystick to one o’clock position

so that indicator arrow on pinion gear

below control panel faces upward. See

Figure 2-23.

Figure 2-23

6. Insert chute control rod into pinion gear

below joystick. Make sure to line up hole

in rod with arrow on pinion gear. See

Figure 2-24.

Figure 2-24

NOTE: Chute control rod will fit snug

into pinion gear. Support rear of dash

panel with one hand while inserting rod

with your other hand to ensure rod is

inserted all the way into pinion gear.

NOTE: The hole in the chute directional

control rod is a reference for aligning

rod with indicator arrow on pinion gear,

and will be visible after rod has been

inserted.

7. Push chute control rod toward control

panel until hole in rod lines up with hole

in chute control input closest to chute

control head and insert hairpin clip (a)

removed in Step 1. See Figure 2-25.

(a)

Figure 2-25

NOTE: Second hole is used to achieve

further engagement of chute control

rod into pinion gear if required. Refer to

Product Care section for Chute Control

Rod adjustments.

8. Finish securing chute control head to

chute support bracket with wing nut (b),

clevis pin (d), and bow-tie cotter pin (e)

removed in Step 1.

STOP

Continue to Set-Up (page 12).

10 Section 2 — ASSembly & Set-Up

Overhead Chute Control (w/ Flex

Shaft & Steel Chute)

Chute

Assembly

Flex

Shaft

Figure 2-26

1. Remove lock nuts (a) and hex screws (b)

from chute support bracket (this will

require two wrenches). See Figure 2-27.

Chute

Assembly

Chute Base

Chute Support

Bracket

Chute Control Head

(a)

(b)

Figure 2-27

2. Place chute assembly onto chute base

and chute control head onto chute

support bracket. See Figure 2-27.

3. Secure chute control head to chute

support bracket with lock nuts (a) and

hex screws (b) removed in Step 1.

See Figure 2-28.

(a)

(b)

Figure 2-28

NOTE: For smoothest operation, cables should

all be to the left of the chute directional

control rod.

4. Remove hairpin clip (a) from rear of

chute control assembly. See Figure 2-29.

(a)

(b)

Figure 2-29

5. Insert flex shaft (b) removed during

Handle Assembly from lower handle

into rear of chute directional control

head. See Figure 2-29. Secure flex shaft

to chute control head with hairpin clip

(a) removed in Step 4.

6. Perform one of the following to connect

the flex shaft to the chute control rod

coupling:

• Units with Crank Chute Control -

Insert hex end of flex shaft into

chute control rod coupling under

dash panel. See Figure 2-30.

Figure 2-30

• Units with Electric Chute Control -

Insert other end of flex shaft into

chute control rod coupling under

dash panel. Make sure to line up flat

end of rod and flat end of coupler.

You may need to rotate rod around

until these two surfaces line up. See

Figure 2-31 inset.

Figure 2-31

7. Ensure speed selector is in fastest

forward speed.

8. Remove cotter pin (a) and washer (b)

from ferrule on end of shift rod.

See Figure 2-32 inset.

(a)

(b)

Shift Rod

Ferrule

Figure 2-32

9. Make sure the shift lever on the back of

the transmission is rotated downward to

the full extent of its rotation. See Figure

2-33, Detail “A” for models without

hydro transmission or Detail “B” for

models with hydro transmission.

A B

Figure 2-33

10. Insert ferrule into top hole of shift

lever and secure with cotter pin (a) and

washer (b) removed in Step 8. See Figure

2-32. Ferrule may need to be adjusted

up or down.

STOP

Continue to Set-Up (page 12).

11Section 2 — ASSembly & Set-Up

2. Insert round end of chute control rod

into chute control head. Push rod as

far into chute control head as possible,

keeping holes in rod pointing upward.

See Figure 2-36.

Figure 2-36

3. Place chute onto chute base and ensure

chute control rod is positioned under

handle panel. Secure chute control head

to chute support bracket with

clevis pin (d) and bow-tie cotter pin (e)

removed in Step 1. See Figure 2-37.

(d)

(e)

Figure 2-37

4. Finish securing chute control head by

installing hex screw (c) and wing nut (b)

removed in Step 1. See Figure 2-38.

(c)

(b)

Figure 2-38

5. Insert other end of chute control rod

into coupler below handle panel. Make

sure to line up flat end of rod and flat

end of coupler. You may need to rotate

rod around until these two surfaces line

up. See Figure 2-39 inset.

Figure 2-39

6. Push chute control rod toward the

control panel until hole in rod lines up

with middle hole in chute control input

and insert cotter pin (a) removed in

Step 1. See Figure 2-40.

(a)

Figure 2-40

NOTE: There is a reference hole

provided at rear end of control rod to

help know when holes are vertical.

NOTE: Hole furthest from chute

control head is used to achieve further

engagement of chute control rod into

coupler, if required. Refer to Product

Care section for Chute Control Rod

adjustment on page 23.

NOTE: For units equipped with manual

chute control rods, the hole closest

to chute control head is used for

manual movement of chute assembly if

required. Refer to Controls & Operation

section on page 18.

STOP

Continue to Set-Up (page 12).

Electric Chute Control

Chute Control Rod

Manual Chute

Control Rod

Chute

Assembly

Figure 2-34

1. Remove cotter pin (a), wing nut (b) and

hex screw (c) from chute control head.

Remove clevis pin (d) and bow-tie cotter

pin (e) from chute support bracket.

See Figure 2-35.

(c)

(e)

Chute

Chute Support

Bracket

Chute Base

(a)

(d)

(b)

Chute Control

Head

Figure 2-35

NOTE: For smoothest operation, cables should

all be to the left of the chute directional

control rod.

12 Section 2 — ASSembly & Set-Up

Set-Up

Chute Control Cable Routing (If

Equipped)

For units equipped with 2-way or 4-way chute

control joystick, electric chute control and/or

chute-pitch controls, ensure control cables are

routed properly.

Chute control cables are routed through a

single wire guide (a) on top of the engine and/

or through two wire guides (b) located on the

left side of the unit. See Figure 2-41.

NOTE: On units equipped with a cable tie

securing the cables to the rear of the gas tank,

pull the cables toward the chute and pull the

cable tie snug to secure the cables in place.

NOTE: For smoothest operation, cables should

all be to the left of the chute directional

control rod (c).

NOTE: The number of cables routed through

the wire guides will depend on unit model.

1. Locate cable guide(s) and perform the

following:

• Units with Top Mounted Wire Guide (a) -

Check that all cables are properly routed

through cable guide on top of engine.

See Figure 2-41.

• Units with Side Mounted Wire Guides

(b) - Check that all cables are properly

routed through the wire guide below

the left side of the engine and the wire

guide below the chute control head.

See Figure 2-41.

(b)

(a)

(c)

(b)

Figure 2-41

Shear Pins Storage (If Equipped)

On select units, holes are provided in the rear

of the handle panel for shear pin (a) and bow-

tie cotter pin (b) storage as shown in Figure

2-42. If not provided, make sure to store them

in a safe place until needed.

(a)

(b)

(a)

(b)

(a)

(b)

Figure 2-42

Drift Cutters (If Equipped)

The drift cutters are mounted inverted at the

factory for shipping purposes.

Standard

1. Remove two screws (a) and lock nuts (b)

that secure each drift cutter, and remove

them from the sides of auger housing.

See Figure 2-43.

(a)

(b)

Figure 2-43

2. Turn the drift cutters around and

position them as shown in Figure 2-43 to

the outside of the auger housing.

3. Attach drift cutters with screws (a) and

lock nuts (b) removed in Step 1.

Tool-less

1. Remove two carriage bolts (a) and wing

nuts (b) that secure each drift cutter, and

remove them from the sides of auger

housing. See Figure 2-44.

(b)

(a)

(b)

(a)

Tool-less Adjustable

Drift Cutter

Tool-less Non-Adjustable

Drift Cutter

Figure 2-44

2. Turn the drift cutters around and

position them as shown in Figure 2-44

to the outside of the auger housing.

3. Attach drift cutters with carriage bolts

(a) and wing nuts (b) removed in Step 1.

Skid Shoes (If Applicable)

Select models require the installation to the

provided skid shoes.

1. Using the two carriage bolts (a) and

hex flange nuts (b) and flat washers (if

equipped) (c), secure the skid shoe to

the auger housing (d). Hand tighten hex

flange nuts. See Figure 2-45.

2. Adjust the skid shoe to provide a

minimum of 1/8th inch clearance

between the shave plate (e) and the

ground. Securely tighten hex flange

nuts.

3. Repeat Step 1 to install the remaining

skid shoe.

4. If necessary refer to Skid Shoes in the

Adjustments section on page 13.

NOTE: Augers not shown for clarity

(a)

(c)

(b)

(d)

(e)

Figure 2-45

13Section 2 — ASSembly & Set-Up

Chute Clean-Out Tool

The chute clean-out tool is fastened to the top

of the auger housing with a mounting clip. See

Figure 2-46.

Figure 2-46

Tire Pressure (If Applicable)

NOTE: Not applicable to those units equipped

with airless tires.

WARNING!

Under any circumstance do not exceed manufacturer’s

recommended psi. Equal tire pressure should be

maintained at all times. Excessive pressure when

seating beads may cause tire/rim assembly to burst

with force sufficient to cause serious injury. Refer to

sidewall of tire for recommended pressure.

The tires are over-inflated for shipping

purposes. Check tire pressure before

operating unit. Refer to tire side wall for tire

manufacturer’s recommended psi and deflate

(or inflate) tires as necessary.

NOTE: Equal tire pressure is to be maintained

at all times for performance purposes.

Skid Shoes

On selected models, snow blower skid shoes

are adjusted at the factory set roughly 1/8”

below the shave plate. Adjust them downward,

if desired, prior to operating the snow blower.

CAUTION

Use extreme caution when on gravel and adjust auger

housing height to clear gravel or crushed rock surfaces to

avoid picking up and throwing gravel or crushed rock.

• For close snow removal on a smooth

surface, raise skid shoes higher on auger

housing.

• Use a lower position when area to be

cleared is uneven, such as a gravel

driveway.

NOTE: If you choose to operate unit on a

gravel surface, keep skid shoes in position for

maximum clearance between ground and

shave plate.

To adjust skid shoes:

1. Loosen four hex nuts (a) (two on each

side) and carriage bolts (b). Move skid

shoes to desired position. See Figure

2-49.

(b) (b)

(a)

Figure 2-49

NOTE: The skid shoes on your unit may

look slightly different (and have different

hardware) than ones shown in Figure 2-49.

2. Make certain entire bottom surface of

skid shoe is against ground to avoid

uneven wear on skid shoes.

3. Retighten hex nuts (a) and carriage bolts

(b) securely.

Adjustments

Chute Assembly

NOTE: For models with 2-Way/4-Way or Electric

Chute Directional Control and/or models

with chute-pitch controls see Controls and

Operation on page 18-19.

On units with manual chute tilt, the distance

snow is thrown can be adjusted by changing

angle of chute assembly. To do so:

1. Loosen wing knob found on left side of

chute assembly. See Figure 2-47.

Figure 2-47

2. Pivot chute upward or downward before

retightening wing knob.

Drift Cutters (If Equipped)

The drift cutters are mounted inverted at the

factory for shipping purposes.

1. Loosen the two carriage bolts (a) and

wing nuts (b) that secure each drift

cutter to the sides of auger housing. See

Figure 2-48.

(b)

(a)

Figure 2-48

2. Slide the drift cutters to desired height.

3. Securely tighten the two carriage bolts

and wing nuts that secure each drift

cutter to the sides of auger housing.

14 Section 2 — ASSembly & Set-Up

Shave Plate

NOTE: This procedure applies to units

equipped with adjustable shave plates only.

To adjust the shave plate:

1. Allow engine to run until it is out of fuel.

Do not attempt to pour fuel from the

engine.

2. Carefully pivot unit up and forward so

that it rests on auger housing.

3. Loosen rear skid shoe bolts (a) on both

sides of auger housing and remove

carriage bolts (b) and hex nuts (c) which

attach shave plate (d) to the bottom of

the auger housing. See Figure 2-50.

(b)

(d)

(b) (b)

(a) (a)

(b)

Figure 2-50

NOTE: 3-Stage unit shown.

4. Adjust the shave plate to one of 2

mounting positions. Reinstall and

tighten the carriage bolts (b) and hex

nuts (c) all bolts securely. See Figure

2-50.

5. Adjust the skid shoes. See Skid Shoes on

page 13.

Auger Control

WARNING!

Prior to operating your unit, carefully read and follow

all instructions below. Perform all adjustments to verify

your equipment is operating safely and properly.

Refer to Controls & Operation section (page

17) for the location of auger control lever and

check adjustment as follows:

1. When auger control lever is released and

in disengaged “UP” position, the cable

should have very little slack. It should

NOT be tight.

2. In a well-ventilated area, start the snow

blower engine. Refer to your Engine

Operator’s Manual.

3. While standing in the operator’s

position (behind the unit), depress the

auger control lever to engage auger.

4. Allow auger to remain engaged for

approximately ten (10) seconds before

releasing auger control lever. Repeat this

several times.

5. With auger control lever in disengaged

“UP” position, walk to front of machine.

6. Confirm that auger has completely

stopped rotating and shows NO signs

of motion. If auger shows ANY signs

of rotating, immediately return to

operator’s position and shut OFF engine.

Wait for ALL moving parts to stop before

readjusting auger control lever.

7. To readjust the auger control cable,

loosen upper hex screw (a) on auger

control bracket. See Figure 2-51.

Auger Control

Bracket

(a)

Figure 2-51

8. Position bracket upward to provide

more slack (or downward to increase

cable tension). See Figure 2-51.

Retighten upper hex screw (a).

9. Repeat Steps 1-6 to verify proper

adjustment has been achieved.

Shift Cable (If Equipped)

If full range of speeds (forward and reverse)

cannot be achieved use the mounting holes

in the index bracket to adjust the shift cable

tension as follows:

1. Place shift lever in fastest forward speed

position.

2. Lift the shift cable index bracket (a)

up to create slack in the cable (b). See

Figure 2-52.

(b)

(c)

(a)

Figure 2-52

3. Disengage the Z fitting (c) from the

index bracket.

4. Select new mounting hole and reinsert

Z fitting into the index bracket.

Using the upper mounting holes will

loosen the shift cable. Using the lower

mounting holes will tighten the shift

cable.

5. Reinsert the Z fitting into the index

bracket.

6. To ensure proper shift cable tension

perform the following:

a. Start the engine and place the shift

lever in the slowest forward speed.

Using the drive control, ensure the

unit moves forward.

b. Place the shift lever in the slowest

reverse speed. Using the drive

control, ensure the unit moves in

reverse.

c. If necessary continue to adjust

cable until the conditions in Steps

a and b are satisfied.

15Section 2 — ASSembly & Set-Up

Shift Rod (If Equipped)

If full range of speeds (forward and reverse)

cannot be achieved, adjust shift rod as follows:

1. Place shift lever in fastest forward speed

position.

2. Remove cotter pin (a) and washer (b)

from adjustment ferrule on shift rod and

pull it out from shift lever. See Figure

2-53.

(a)

(b)

Figure 2-53

3. Make sure the shift lever on the back of

the transmission is rotated downward to

the full extent of its rotation. See Figure

2-54, Detail “A” for models without

hydro transmission or Detail “B” for

models with hydro transmission.

A B

Figure 2-54

4. Rotate ferrule up or down on shift rod

as necessary until it lines up with upper

hole in shift lever. Refer to Figure 2-53

inset.

5. Insert the ferrule into the upper hole

and secure with the washer and cotter

pin.

Drive Control (Models with out Hydro

Transmission) (If Equipped)

When drive control lever is released and in

disengaged “UP” position, cable should have

very little slack. It should NOT be tight.

NOTE: If excessive slack is present in drive

cable or if unit’s drive is disengaging

intermittently during operation, the cable may

be in need of adjustment.

Check adjustment of drive control levers

follows:

1. With drive control lever released, push

unit gently forward. It should roll freely.

2. Engage drive control lever and gently

attempt to push the unit forward. The

wheels should not turn. The unit should

not roll freely.

3. If equipped with a shift lever, with drive

control lever released, move shift lever

back and forth between the R2 position

and the F6 position several times. There

should be no resistance in the shift lever.

If any of the above tests failed, the drive cable

is in need of adjustment. Proceed as follows:

1. Shut OFF engine. Refer to the Engine

Operator’s Manual.

2. Loosen lower hex screw on drive cable

bracket. See Figure 2-55.

Drive Cable

Bracket

Hex Screw

Figure 2-55

3. Position bracket upward to provide

more slack (or downward to increase

cable tension).

4. Retighten lower hex screw.

5. Check adjustment of drive control lever

as described above to verify proper

adjustment has been achieved.

Drive Control (Models with Hydro

Transmission) (If Equipped)

When drive control lever is released and in

disengaged “UP” position, cable should have

very little slack. It should NOT be tight.

NOTE: If excessive slack is present in drive

cable or if unit’s drive is disengaging

intermittently during operation, the cable may

be in need of adjustment.

1. Shut OFF engine. Refer to the Engine

Operator’s Manual.

2. Loosen upper hex screw on drive cable

bracket. See Figure 2-56.

Drive Cable

Bracket

Hex Screw

Figure 2-56

3. Position bracket upward to provide

more slack (or downward to increase

cable tension).

4. Retighten upper hex screw.

5. Check for excessive slack in drive control

cable. If necessary repeat Steps 2-4 to

re-adjust the drive control.

Adding Fuel & Oil

Refer to the Engine Operator’s Manual for

information on adding fuel and oil.

Controls & Operation

*If Equipped

Standard Chute

Directional Control*

Shift Lever*

Augers

Skid Shoe

Clean Out

Tool

Chute Assembly

Drive Control Lever*

Auger Control Lever*

Auger Housing

LED Light Bar*

Drift Cutters*

Overhead

Chute

Directional

Control*

Heated

Grips*

Shift Lever

4-Way/2-Way

Chute

Directional

Control

Joystick*

Chute

Control

Rod*

Manual

Chute

Directional

Control

(Shown)

Chute

Control Rod*

Electric Chute

Directional

Control

Joystick*

Steering

Trigger

Control

Headlight*

Flex Shaft

Chute

Directional

Control*

Heated Grip Switch*

Two-Way

Chute-Pitch

Control™*

Overhead

Chute

Directional

Control*

Shift Lever

Two-Way Indexed

Chute-Pitch

Control*

Heated Grip Switch*

Headlight*

Figure 1-1

17Section 3 — controlS & operation

Snow blower controls and features are

described below and illustrated in Figure 3-1.

NOTE: This Operator’s Manual covers several

models. Snow blower features may vary by

model. Not all features in this manual are

applicable to all snow blower models and the

snow blower depicted may differ from yours.

NOTE: All references to the left or right side

of the snow blower are from the operator’s

position. Any exceptions will be noted.

Engine Controls

Refer to the Engine Operator’s Manual for

details regarding all engine-related controls

and features.

Shift Lever (6-Speed

Transmission) (If Equipped)

The shift lever is located on the handle panel

and is used to determine ground speed and

direction of travel.

Forward

There are six forward (F) speeds. Position

one (1) is the slowest and position six (6) is the

fastest.

Reverse

There are two reverse (R) speeds. Position one

(1) is the slowest and position two (2) is the

fastest.

Shift Lever (Hydro Transmission)

(If Equipped)

The shift lever is located on the handle panel

and is used to determine ground speed and

direction of travel. The further forward the

lever is the faster the unit will travel. Moving

past the detent position to the reverse

direction will move the unit in reverse.

Chute Assembly

Snow drawn into the auger housing is

discharged out the chute assembly.

Skid Shoes

Position skid shoes based on surface

conditions. Adjust upward for hard-packed

snow. Adjust downward when operating on

gravel or crushed rock surfaces. See Skid Shoe

Adjustment section on page 13 Figure 2-49.

Augers

When engaged, the augers rotate and draw

snow into the auger housing.

Headlight (Single or Double)

(If Equipped)

The headlight is located on the front of the

handle panel and is automatically turned ON

when the engine is started.

LED Light Bar (If Equipped)

The LED headlight is located on top of the

auger housing and is automatically turned ON

when the engine is started.

Drift Cutters (If Equipped)

The drift cutters are designed for use in deep

snow. Their use is optional for normal snow

conditions. Maneuver unit so that the cutters

penetrate a high standing snow drift to assist

snow falling into the augers for throwing.

Heated Grips (If Equipped)

CAUTION

It is recommended that you wear gloves when using

the heated grip. If the heated grips become too hot,

turn it OFF.

To activate the heated grips, move switch

found on top (a) of or on the rear (b) of dash

panel into the ON position. See Figure 3-2. To

turn OFF heated grips, move switch to the OFF

position.

Switch ON Switch OFF

(b)

(a)

(b)

(a)

Switch ON

Switch OFF

Figure 1-2

Auger Control Lever

(If Equipped)

The auger control lever is located on the left

handle. Squeeze the control lever against the

handle to engage the augers and start snow

throwing action. Release to stop. See Figure

3-3.

Figure 1-3

IMPORTANT: Refer to the Auger Control

information in the Assembly & Set-Up section

Page 14 prior to operating your snow blower.

Read and follow all instructions carefully and

perform all adjustments to verify your snow

blower is operating safely and properly.

Drive Control Lever/Auger Clutch

Lock* (If Equipped)

The drive control lever is located on the right

handle. Squeeze the control lever against the

handle to engage the wheel drive. Release to

stop. See Figure 3-4.

Figure 1-4

*On select models, the drive control lever also

locks the auger control lever so that you can

operate the chute directional control without

interrupting the snow throwing process. If the

auger control lever is engaged simultaneously

with the drive control lever, the operator can

release the auger control lever (on the left

handle) and the augers will remain engaged.

Release both control levers to stop augers and

wheel drive.

NOTE: Always release drive control lever

before changing speeds on all units except the

800-series hydro. Failure to do so will result

in increased wear on your machine’s drive

system.

18 Section 3 — controlS & operation

Steering Trigger Controls

(If Equipped)

The left and right wheel steering trigger

controls are located on the underside of the

handles. Refer to Figure 3-5.

IMPORTANT: Units with Hydro Transmission

- When moving the unit without starting the

engine, squeeze both right and left triggers to

disengage the drive.

Figure 1-5

• Squeeze the right trigger control to turn

right.

• Squeeze the left trigger control to turn

left.

CAUTION

Operate the snow blower in open areas until you are

familiar with these controls.

Standard Directional Control (If

Equipped)

The standard chute directional control is

located on the left side of the unit. To change

direction in which snow is thrown, rotate chute

directional control. See Figure 3-6.

Overhead Chute Directional

Control (If Equipped)

The overhead chute directional control is

located at the rear of the snow blower towards

the left side of the unit under the handle

panel. To change the direction in which snow

is thrown, rotate chute directional control. See

Figure 3-6.

Figure 1-6

2-Way Chute Directional Control

Joystick (If Equipped)

The 2-Way chute directional control joystick is

located on the left side of the dash panel.

• To change direction in which snow is

thrown, squeeze button on joystick and

pivot joystick to right or to the left. See

Figure 3-7.

Figure 1-7

4-Way Chute Directional Control

Joystick (If Equipped)

The 4-Way chute directional control joystick is

located on the left side of the dash panel.

• To change the direction in which snow

is thrown, squeeze the button on the

joystick and pivot the joystick to the

right or to the left. See Figure 3-8.

• To change the angle/distance which

snow is thrown, pivot the joystick

forward or backward.

Figure 1-8

Electric Chute Directional

Control Joystick (If Equipped)

The electric chute directional control joystick

is located on the right side of the dash panel.

Refer to Figure 3-9.

• To change the direction in which snow

is thrown, move the joystick to the right

or to the left.

• To change the angle/distance which

snow is thrown, pivot the joystick

forward or backward.

DIRECTIONAL CONTROL

ELECTRIC CHUTE

CHUTE

ROTATE

LEFT

CHUTE

ROTATE

RIGHT

CHUTE TILT UP

CHUTE TILT DOWN

Figure 1-9

Manual Chute Directional

Control (Units with Electric

Chute Directional Control

Joystick) (If Equipped)

Follow this procedure to manually change the

chute direction on units equipped with an

electric chute directional control joystick and

manual chute directional control rod only. See

Figure 3-1.

1. Remove cotter pin (a) from either of the

holes furthest from the chute assembly on

chute rotation assembly. See Figure 3-10.

(a)

Figure 1-10

19Section 3 — controlS & operation

2. Push in chute control rod until the hole

in it lines up with the third hole in chute

rotation assembly. See Figure 3-10.

3. Reinsert cotter pin (a) through this hole

and chute control rod as shown in

Figure 3-10.

4. Grasp indented portion of chute control

rod and manually rotate chute assembly

to the right or to the left. See Figure 3-11.

Figure 1-11

Overhead Chute Directional

Control (w/ Flex Shaft) (If

Equipped)

The overhead chute directional control is

located at the rear of the unit towards the

left side under the handle panel. To change

direction in which snow is thrown, rotate chute

directional control. See Figure 3-12.

CHUTE DIRECTIONAL CONTROL

DISCHARGE

LEFT

DISCHARGE

RIGHT

Figure 1-12

Chute-Pitch Control (If Equipped)

The two-way chute-pitch control is located on

the left side of the dash panel and is used to

control the distance of snow discharge from

the chute.

To change the upper chute angle to control the

distance that snow is thrown, pivot the lever

forward or backward. See Figure 3-13.

Two-Way Chute-Pitch Control

• To Reduce the Distance Snow is

Thrown: Move the lever forward to

pivot the upper chute down. See Figure

3-13.

• To Increase the Distance Snow is

Thrown: Move the lever rearward to

pivot the upper chute upward. See

Figure 3-13.

Two-Way Indexed Chute-Pitch Control

• To Reduce the Distance Snow is

Thrown: Disengage lever from the

current chute-pitch setting. Move the

lever forward to pivot the upper chute

down to the desired pitch setting (a).

See Figure 3-13.

• To Increase the Distance Snow is

Thrown: Disengage lever from the

current chute-pitch setting. Move the

lever rearward to pivot the upper chute

upward to the desired pitch setting (a).

See Figure 3-13.

TWO-WAY CHUTE-PITCH CONTROL

CHUTE TILT

DOWN

CHUTE TILT

TWO-WAY INDEXED CHUTE-PITCH CONTROL

CHUTE TILT

DOWN

CHUTE TILT

(a)

Figure 1-13

Starting and Stopping the

Engine

WARNING!

Always keep hands and feet clear of moving parts.

Do not use a pressurized starting fluid. Vapors are

flammable.

Refer to the Engine Operator’s Manual for

instructions on starting and stopping the engine.

Pull StartElectric Start

Figure 1-14

To Engage Drive (Drive Control

Lever Units)

1. With the throttle control in the Fast

(rabbit) position, move the shift lever

into one of the six forward (F) positions

or two reverse (R) positions on 6-speed

units or in the desired position on the

Hydro units. Select a speed appropriate

for the snow conditions and a

comfortable pace.

2. Squeeze the drive control lever against the

handle and the snow blower will move.

Release it and drive motion will stop.

20 Section 3 — controlS & operation

To Engage Augers

To engage the augers and start throwing snow,

squeeze the auger control lever against the left

handle. Release to stop the augers.

To Steer (If Equipped)

With the drive control lever engaged, squeeze the

right steering trigger control to turn right. Squeeze

the left steering trigger control to turn left.

CAUTION

Operate the snow blower in open areas and at slow

speeds until you are familiar with the drive control and

comfortable operating the steering controls.

Replacing Shear Pins

CAUTION

NEVER replace the auger shear pins with anything

other than OEM Part No. 738-04124A (gold colored

replacement shear pins) or 738-05273 (Black colored

replacement shear pins). Any damage to the auger

gearbox or other components as a result of failing to do

so will NOT be covered by your snow blower’s warranty.

WARNING!

Always turn OFF the snow blower’s engine and remove

the key prior to replacing shear pins.

The augers are secured to the spiral shaft with

shear pins (a) and cotter pins (b). If the auger

should strike a foreign object or ice jam, the

snow blower is designed so that the pins may

shear. If the augers will not turn, check to see if

the pins have sheared. See Figure 3-15.

IMPORTANT: ALWAYS use the correct OEM

replacement shear pin.

2-Stage Snow Blowers

• The auger is secured to the spiral shaft

using gold colored shear pins (OEM Part

No. 738-04124A).

3-Stage Snow Blowers

• The side and central accelerator augers

are secured to the spiral shaft using

black shear pins (OEM part number

738-05273).

NOTE: 3-Stage shown.

(a)

(b)

Figure 1-15

IMPORTANT: On 3-stage units, there is an

additional shear pin in the rear accelerator.

Clearing a Clogged Chute

Assembly

WARNING!

Never use your hands to clear a clogged chute assembly.

Shut OFF engine and remain behind handles until all

moving parts have stopped before unclogging.

The chute clean-out tool is conveniently

fastened to the rear of the auger housing

with a mounting clip. Should snow and ice

become lodged in the chute assembly during

operation, proceed as follows to safely clear

the chute assembly and chute opening:

1. Release both the auger control lever/bail

and the drive control lever/bail.

2. SHUT THE ENGINE OFF! Refer to the

Engine Operator’s Manual. Remove the

safety key.

3. Remove clean-out tool from the clip

which secures it to the rear of the auger

housing.

4. Use the shovel-shaped end of the clean-

out tool to dislodge and scoop any snow

and ice which has formed in and near

the chute assembly. Always use the

clean-out tool (Part # 931-2643), not your

hands. Refer to the separate supplement

for clean-out tool ordering information.

See Figure 3-16.

5. Re-fasten the clean-out tool to the

mounting clip on the rear of the auger

housing, reinsert the safety key and start

the snow blower’s engine.

6. While standing in the operator’s

position (behind the snow blower),

engage the auger control lever/bail for

a few seconds to clear any remaining

snow and ice from the chute assembly.

Figure 1-16

La page charge ...

Troy-Bilt 31BH5DR7563 Mode d'emploi

Marque: Troy-Bilt

Modèle: 31BH5DR7563

Catégorie: Souffleuses à neige

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Troy-Bilt 31BH5DR7563 Operating instructions

Troy-Bilt 31BH5DR7563 Mode d'emploi

Ce manuel convient également à

Troy-Bilt 31BH5DR7563 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents