NAPOLEON NEFL42/50/60FH-MT Le manuel du propriétaire

Catégorie
Cheminées
Taper
Le manuel du propriétaire

Ce manuel convient également à

EN
W415-2172 / A / 11.10.17
FR
PG
27
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
1.16G
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone 1 (866) 820-8686 • www.napoleonfi replaces.com •[email protected]
SAFETY INFORMATION
!
WARNING
If the information in these instructions
are not followed exactly, a fi re may result
causing property damage, personal injury
or loss of life.
- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.
$10.00
FOR INDOOR USE ONLY!
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278
NEFL42FH-MT, NEFL50FH-MT &
NEFL60FH-MT
ELECTRIC APPLIANCE
EN
W415-2172 / A / 11.10.17
2
TABLE OF CONTENTS
1.0 INTRODUCTION 3
1.1 DIMENSIONS 4
1.2 LISTING APPROVALS 4
1.3 GENERAL INSTRUCTIONS 5
1.4 UNPACKING AND TESTING APPLIANCE 5
1.5 HARDWARE PARTS LIST 6
1.6 RATING PLATE INFORMATION 7
2.0 LOCATING APPLIANCE 8
2.1 GROUNDING APPLIANCE 8
3.0 INSTALLATION 9
3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 9
3.2 MINIMUM MANTEL CLEARANCES 9
3.3 FRAMING 10
3.4 INSTALLING THE APPLIANCE ONTO THE WALL 11
3.5 RECESSING THE APPLIANCE INTO THE WALL 12
3.6 INSTALLING THE APPLIANCE INTO A MANTEL 13
3.6.1 RUBBER FEET INSTALLATION 14
3.7 HARD WIRING INSTALLATION 15
4.0 FINISHING 16
4.1 MESH TRIM FRONT INSTALLATION 16
4.2 MESH TRIM FRONT REMOVAL 17
4.3 CRYSTAL EMBER INSTALLATION 17
5.0 OPERATING INSTRUCTIONS 18
5.1 MAIN POWER BUTTON 18
5.2 OPERATING TOUCH DISPLAY PANEL AND REMOTE CONTROL 18
6.0 MAINTENANCE 19
6.1 REMOTE BATTERY INSTALLATION 19
7.0 WIRING DIAGRAM 20
8.0 REPLACEMENT PARTS 21
9.0 TROUBLESHOOTING 23
10.0 WARRANTY 24
11.0 NOTES 25
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
Batteries must be disposed of according to the local laws and regulations. Some batteries may be
recycled, and may be accepted for disposal at your local recycling center. Check with your
municipality for recycling instructions.
Les piles doivent être mises au rebut conformément aux lois et à la réglementation locales.
Certaines piles peuvent être recyclées et acceptées dans votre centre de recyclage local. Rensei-
gnez-vous auprès de votre municipalité au sujet des directives de recyclage.
Las baterías deben desecharse de acuerdo con las leyes y regulaciones locales. Algunas baterías
pueden reciclarse, y es posible que su centro de reciclado local las acepte para desecharlas.
Consulte en su municipalidad sobre las instrucciones para el reciclado.
EN
W415-2172 / A / 11.10.17
3
1.0 INTRODUCTION
!
WARNING
3.7C
C
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF
CONTACTED.
Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fi re or injury.
Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.
Do not install damaged, incomplete or substitute components.
Do not burn wood or other materials in this appliance.
Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.
Clothing or other fl ammable material should not be placed on or near the appliance.
Due to high temperatures, the appliance should be located out of traffi c and away from furniture and
draperies.
Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.
Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
Check with your local hearth specialty dealer for safety screens and hearth guards to protect children
from hot surfaces. These screens and guards must be fastened to the fl oor.
Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
It is imperative that the control compartments, circulating blower and its passageway in the appliance
and are kept clean. The appliance should be inspected before use and at least annually by a qualifi ed
service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding
material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and
other fl ammable vapors and liquids.
Under no circumstances should this appliance be modifi ed.
Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician
to inspect the appliance and to replace any part of the control system which has been under water.
Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the
glass should be done by a licensed or qualifi ed service person.
Do not strike or slam shut the appliance glass door.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.
Servicing should be done only while the appliance is disconnected from the power supply circuit.
Always unplug appliance when not in use.
Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been
dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
Do not use outdoors.
Never locate appliance where it may fall into a bathtub or other water container.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord
away from traffi c area and where it will not be tripped over.
Connect to properly grounded outlets only.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fi re, or damage the appliance.
To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a carpet, where openings may become blocked.
Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or
relocatable power tap (outlet/power strip).
Ensure clearances to combustibles are maintained when building a mantel or shelves above the
appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,
discolouration or damage to decorations, a T.V. or other electronic components.
EN
W415-2172 / A / 11.10.17
4
1.1 DIMENSIONS
1.2 LISTING APPROVALS
This appliance has been tested in accordance with the CSA Standards for fixed and location-dedicated
electric room appliances in the United States and Canada. If you need assistance during installation, please
contact your local dealer.
NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in
the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United
States or the Canadian Electric Code, CSA C22.1 in Canada.
Description
Electric Appliance
Type
There are 3 ways to install the unit :
Wall-Mount, Recess into Wall and
Assemble with mantel
Voltage
120V AC
Watts
MAX 1500W
Amps
15 AMP Grounded Circuit
MODEL NO. NET WEIGHT GROSS WEIGHT
NEFL42FH-MT
44.3 lbs (20.1kg) 60.2 lbs (27.3kg)
NEFL50FH-MT
50.9 lbs (23.1kg) 63.4 lbs (29.2kg)
NEFL60FH-MT
61.3 lbs (27.8kg) 73.4 lbs (33.3kg)
A
B
G
F
E
D
C
FRONT VIEW
SIDE VIEW
TOP VIEW
DIMENSIONS
MODEL NO. A B C D E F G
NEFL42FH-MT
42"
(1067mm)
21 5/8"
(550mm)
5 1/3"
(136mm)
20 1/2"
(520mm)
37 1/2"
(951mm)
12"
(304mm)
32 8/16"
(827mm)
NEFL50FH-MT
50"
(1270mm)
21 5/8"
(550mm)
5 1/3"
(136mm)
20 1/2"
(520mm)
45 7/16"
(1154mm)
12"
(304mm)
40 1/2"
(1030mm)
NEFL60FH-MT
60"
(1524mm)
21 5/8"
(550mm)
5 1/3"
(136mm)
20 1/2"
(520mm)
55 5/16"
(1405mm)
12"
(304mm)
50 5/8"
(1287mm)
EN
W415-2172 / A / 11.10.17
5
1.3 GENERAL INSTRUCTIONS
4.8B
A.
Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the
outlet are on.
B.
The appliance may emit a slight, harmless odour when fi rst used. This odour is normal and it is caused
by the initial heating of internal appliance elements and will not occur again.
C.
If your appliance does not emit heat, consult the operation section of this manual for further
information.
D.
Use with a CSA- or UL-certifi ed surge protector.
E.
Do not route the power cord directly underneath the appliance.
This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured
homes when installed according to these instructions.
!
WARNING
READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO
FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE
IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL
ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT
SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR
RESULT IN A SAFETY HAZARD.
DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.
DO NOT USE DAMAGED ELECTRICAL CORDS.
SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE
POWER SUPPLY CIRCUIT.
TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF
RECEPTACLE AND FULLY INSERT.
As with most electronic devices, your new electric appliance has been designed to operate at
temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the fireplace
to reach room temperature before turning it on.
1.4 UNPACKING AND TESTING APPLIANCE
Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the
appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt, 15
Amp grounded outlet.
EN
W415-2172 / A / 11.10.17
6
1.5 HARDWARE PARTS LIST
A - Fireplace
NEFL42FH-60FH-MT (1)
B - Wood Screws
NEFL42FH-50FH-MT (6)
NEFL60FH-MT (12)
C - Drywall Anchors
NEFL42FH-50FH-MT (6)
NEFL60FH-MT (12)
D - ST4x12 Metal Screws
NEFL42FH-60FH-MT (8)
E - Remote Control
NEFL42FH-60FH-MT (1)
F - Wall Bracket
NEFL42FH-50FH-MT (1)
NEFL60FH-MT (2)
G - Crystals
NEFL42FH-60FH-MT (2)
H - Cover Plate
NEFL42FH-60FH-MT (1)
I - Strain Relief
NEFL42FH-60FH-MT (1)
J - Metal Bracket K - Cord Corner
NEFL42FH-60FH-MT (2)
L - Cord Coupler
NEFL42FH-60FH-MT (2)
M - Cord Cover
NEFL42FH-60FH-MT (2)
N - Rubber Foot
NEFL42FH-50FH-MT
NEFL60FH-MT
( 6 )
( 4 )
NEFL42FH-60FH-MT (4)
EN
W415-2172 / A / 11.10.17
7
1.6 RATING PLATE INFORMATION
This illustration is for reference only. Refer to the rating plate on the appliance for accurate
information.
NOTE: The rating plate must remain with the appliance at all times. It must not be removed.
W385-2162
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 2021 / HOMOLOGUÉ SELON
LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 2021
Page 1 of 1
FOYER À ÉLECTRIQUE. HOMOLOGUÉ POUR
INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE
SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR
INSTALLATION DANS UNE MAISON MOBILE.
ELECTRIC FIREPLACE. SUITABLE FOR BEDROOM
AND BED-SITTING ROOM INSTALLATION. SUITABLE
FOR MOBILE HOME INSTALLATION.
VOLTAGE: 120 VAC TENSION: 120VCA
FREQUENCY: 60Hz FRÉQUENCE: 60Hz
POWER: 1500W PUISSANCE: 1500W
DATE CODE: XXXXX CODE DE DATE:
DESIGNED IN NORTH AMERICA
BY WOLF STEEL LTD.
MADE IN CHINA FABRIQUÉ EN CHINE
WOLF STEEL LTD.
24 NAPOLEON ROAD,
BARRIE, ON, L4M 0G8 CANADA
SERIAL NUMBER/NO. DE SÉRIE:
NEFL
MATERIAL: CLASS IIIA-2 PERMANENT LEXAN ADHESIVE LABEL, MINIMUM THICKNESS 0.1MM, 121°C (250°F) RATING
SPECIFICATION: BLACK LETTERING ON SILVER BACKGROUND. MINIMUM FONT SIZE TO BE MINIMUM OF 8.5 PT (3.2mm)
MAX OVERALL SIZE: 6" x 3"
SERIAL NUMBERS TO BE ASCENDING FROM NEFL
TITLE: RATING PLATE NEFL32/42/50/60/72/100FH-MT
REVISION:
DWG#: W385-2162
DATE: 06.22.16
MODELS / MODÈLES
CEFL32FH-MT
DÉSIGN AMÉRIQUE DU NORD
PAR WOLF STEEL LTÉE.
MASTER CONTRACT: 161746
CONTRAT-CADRE: 161746
NEFL32FH-MT
NEFL42FH-MT CEFL42FH-MT
NEFL50FH-MT CEFL50FH-MT
CEFL60FH-MT
NEFL60FH-MT
NEFL72FH-MT
CEFL72FH-MT
NEFL100FH-MT
CEFL100FH-MT
SAMPLE
EN
W415-2172 / A / 11.10.17
8
!
WARNING
2.0 LOCATING APPLIANCE
2.1 GROUNDING APPLIANCE
DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF
TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,
CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.
NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER
WATER CONTAINER.
WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND
MAINTENANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE
MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED
OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.
DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)
96.1
GROUNDING METHODS
METAL SCREW
(A)
NOT ALLOWED IN CANADA
GROUNDING
MEANS
ADAPTER
GROUNDING PIN
COVER OF
GROUNDED
OUTLET BOX
(C)
(B)
This appliance is for use on 120 volts. The cord has a plug
as shown in (A). An adapter as shown in (C) is available for
connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding plug extending from the
adapter must be connected to a permanent ground such as
a properly grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove
plug from outlet.
EN
W415-2172 / A / 11.10.17
9
3.0 INSTALLATION
Your appliance is a wall-mounted, recessed and/or mantel-installed appliance. Select a suitable location that
is not susceptible to moisture and is away from drapes, furniture and high traffic areas.
NOTE: Follow all National and local electrical codes.
!
WARNING
RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID
TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN
CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD
AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.
RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT
USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.
RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.
USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE
WARRANTY AND/OR RESULT IN A SAFETY HAZARD.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.
HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE
HAZARD.
DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.
68.5A
3.1 MINIMUM CLEARANCE TO COMBUSTIBLES
Measurements are taken from the mesh trim front:
Bottom 0" Top 8" (203mm) to mantel
Sides 0" Top 8" (203mm) to ceiling
Back 0"
8" (203mm)
Mantel
Floor
Wall
!
WARNING
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION. LIGHTER COLOURED PAINTS/LACQUERS
MAY DISCOLOUR.
3.2 MINIMUM MANTEL CLEARANCES
5"
127mm
A
3 1/2"
89mm
MIN
MAX
A
B
B
Finishing Material
(NON-LOAD
BEARING)
MODEL NO. A B
NEFL42FH-MT 21" (53.5cm) 38" (96.5cm)
NEFL50FH-MT 21" (53.5cm) 45 15/16" (116.6cm)
NEFL60FH-MT 21" (53.5cm) 55 13/16" (141.8cm)
EN
W415-2172 / A / 11.10.17
10
3.3 FRAMING
SIDE VIEW
BODY
MESH TRIM
21 5/8"
550mm
Measurements are taken from the body of the appliance:
Sides, back and top 0"
EN
W415-2172 / A / 11.10.17
11
3.4 INSTALLING THE APPLIANCE ONTO THE WALL
Due to the many different materials used on different walls, it is highly recommended to consult your local
builder before installing this appliance on the wall.
A. Select a location that is not prone to moisture and is located at least 36" (91.4cm) away from
combustible materials such as curtain drapes, furniture, bedding, paper, etc.
B. Have 2 people hold the appliance against the wall to determine the final location.
C. Place unit face down on a soft, non abrasive surface. Remove the bracket from the back of the unit
by removing the screws (see illustrations below).
D. Mark out location, then mount the bracket(s) onto the wall using the supplied screws. This bracket
MUST have the hooks facing upward and be level. NOTE: It is strongly recommended that the
mounting bracket be screwed into the wall studs where possible. If the wall studs cannot be
used, ensure that the supplied plastic anchors are used to affix the bracket to the wall and
the bracket is adequately
secured.
E. With the wall mounting bracket
installed, have 2 people lift the
appliance up and insert the
2 hooks on the bracket into
the 2 slots on the back of the
appliance.
F. Check the appliance for stability ensuring that the bracket will not pull free from the wall.
HOOK
SCREWS
HOOK
NEFL42/50FH-MT BRACKET ILLUSTRATED
NEFL60FH-MT BRACKET ILLUSTRATED
Due to the many different finish materials used on walls, it is highly recommended to consult your local
builder before installing this appliance in the wall.
Select a location that is not prone to moisture and is located at least 36" (91.4cm) away from combustible
materials such as curtain drapes, furniture, bedding, paper, etc.
A. Measure the appliance and create a rough in with electrical.
B. Remove the mesh trim. Refer to "MESH TRIM FRONT REMOVAL" section.
C. Hold the appliance up to ensure it will fit into the framing.
D. If the appliance is fully recessed into the wall:
Bend the 2 top tabs upward on the mesh trim front (FIG. 3, next page).
Use the 6 screws (provided) to lock the appliance into the wall with the existing 2 side
flanges (FIG. 1).
Install the media and reinstall the mesh trim front.
E. If partial recess into the wall:
Use the 2 mounting brackets (supplied) to lock the appliance to the wall (FIG. 2).
NOTE: 2 sets of holes are provided for recessing into wall. The wall structure may
limit how far the appliance can be recessed. Use the appropriate set of holes when
recessing to the frame, it may be necessary to use the 4 holes on the top and bottom.
NOTE: It is recommended the walls of the appliance enclosure be finished (ie. drywall) to avoid
exposed insulation or vapour barrier coming in contact with the appliance. This will ensure clearance
to combustibles is maintained.
3.5 RECESSING THE APPLIANCE INTO THE WALL
FIG. 1
FIG. 2
EN
W415-2172 / A / 11.10.17
12
NOTE: The appliance tabs come bent. Tabs must be bent flat by hand when fully recessing the
appliance into the wall (FIG. 4).
A. Remove the mesh trim front. Refer to "MESH TRIM FRONT REMOVAL " section.
B. Install the rubber feet onto the bottom of the appliance for stability. Refer to "RUBBER FEET
INSTALLATION" section.
C. Install the top and bottom brackets provided.
D. Insert the appliance into the mantel and secure it with the brackets, or refer to "ELECTRIC
APPLIANCE MANTEL" installation manual for proper appliance installation instructions.
E. Place the crystal embers along the media tray. Refer to "CRYSTAL EMBER INSTALLATION" section.
F. Reinstall the mesh trim front.
3.6 INSTALLING THE APPLIANCE INTO A MANTEL
FIG. 3
FIG. 4
EN
W415-2172 / A / 11.10.17
13
3.6.1 RUBBER FEET INSTALLATION
A. Place the appliance face down on a soft surface.
B. Using a screw driver, remove the screws on the bottom of the appliance.
C. Install the 4 rubber feet (6 rubber feet for NEFL60FH-MT) onto the bottom of the appliance using the
screws from Step B. See illustrations below.
NOTE: The screws for installing the rubber feet are secured to the appliance. Removal of the screws is
necessary for installing the rubber feet.
NEFL42/50FH-MT ILLUSTRATED
NEFL60FH-MT ILLUSTRATED
EN
W415-2172 / A / 11.10.17
14
3.7 HARD WIRING INSTALLATION
HARD WIRING CONNECTION
If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire
the appliance directly to the house hold wiring.
This appliance must be electrically connected and grounded in accordance with local codes, if hard wired.
In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the
current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
!
WARNING
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED
SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
A. Remove the cover plate from the right side
bottom of the appliance by removing the
3 screws (FIG. 1).
B. Remove the wire connectors from the
power cord. The power cord may
be discarded.
C. Locate the new cover plate, supplied in the hardware bag (FIG. 2). Punch out the 7/8" (22.2mm)
hole and install a box connector through, into the junction box. Snap the box connector clamp onto
the supply wires.
D. Using the wire connectors, connect the ground green wires (G) and the common white wires (N)
together, and then the hot black wires (L) (FIG. 3, 4).
E. Reinstall the cover plate using the 3 screws (FIG. 1).
FIG. 1
COVER PLATE
G
N
L
FIG. 2
7/8" (22.2mm)
Diameter
FIG. 3
FIG. 4
EN
W415-2172 / A / 11.10.17
15
EN
W415-2172 / A / 11.10.17
16
4.0 FINISHING
!
WARNING
POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID
RECONSTRUCTION.
HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.
4.1 MESH TRIM FRONT INSTALLATION
!
WARNING
GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.
IF EQUIPPED WITH DOOR LATCHES THAT ARE PART OF A SAFETY RELIEF SYSTEM, THEY MUST BE
PROPERLY ENGAGED. DO NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.
FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR
OPENINGS, LOUVRE OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR
SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.
BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO
THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.
75.1A
!
WARNING
THE DOOR LATCHES ARE PART OF A SAFETY SYSTEM AND MUST BE PROPERLY ENGAGED. DO
NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.
FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR
OPENINGS, LOUVRE OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR
SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.
BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO
THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.
75.1
THIS WARNING FOR ELECTRICS ONLY:
A. Remove the 2 screws from the top of the appliance.
B. Have 2 people lift the mesh trim up and away from the appliance, holding the mesh trim vertical - not
flat - while carrying. Place the mesh trim face down onto a soft, non-abrasive surface, being careful
not to flex the mesh trim.
C. Bend the top tabs flat (FIG. 1).
D. Install the crystal embers. Refer to "CRYSTAL EMBER INSTALLATION" section.
E. Install the mesh trim front by aligning with the pins on the appliance. Press the mesh trim in and down
to securely engage with the brackets. It must be fully engaged to ensure the touch display panel
performs properly.
F. Secure the mesh trim front using the screws provided to the top of the appliance (FIG. 2, next page).
If appliance is fully recessed, this is not necessary.
FIG. 1
EN
W415-2172 / A / 11.10.17
17
FIG. 2
The mesh trim front must be removed and the appliance must be secured in its final location before the crys-
tal embers are installed.
A. Carefully place crystal embers into the bottom media tray on
the front of the appliance as illustrated. Apply an even layer
from side to side.
B. Ensure that no crystal embers touch the mesh trim front during
install. Avoid crystal embers scratching/tearing mesh.
A. Remove the 2 screws from the top of the appliance. See illustrations below.
B. Have 2 people lift the mesh trim up and away from the appliance, holding the mesh trim vertical - not
flat - while carrying. Place the mesh trim face down onto a soft, non-abrasive surface, being careful
not to flex the mesh trim.
C. Install the crystal embers. Refer to "CRYSTAL EMBER INSTALLATION" section. Install the front
mesh trim by aligning with the pins on the appliance. This ensures the touch display panel performs
properly.
FOR WALL-MOUNT, PARTIAL-RECESS AND MANTEL-INSTALLED APPLIANCE ONLY:
4.2 MESH TRIM FRONT REMOVAL
4.3 CRYSTAL EMBER INSTALLATION
EN
W415-2172 / A / 11.10.17
18
5.0 OPERATING INSTRUCTIONS
Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.
NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power
failure, the appliance will lose its memory function and will reset to factory mode when the power
returns.
The main power button is located on the front bottom right side of the appliance.
5.1 MAIN POWER BUTTON
5.2 OPERATING TOUCH DISPLAY PANEL AND REMOTE CONTROL
POWER
Turns the appliance ON/OFF.
FLAME - ORANGE
FLAME - BLUE
TIMER
TEMPERATURE
Controls Orange Flame brightness.
6 Settings
: ( F5-F4-F3-F2-F1-F0 ) Flame dims from F5 to F1.
F5 is the brightest setting and F0 is off.
Controls Blue Flame brightness.
6 Settings
: ( F5-F4-F3-F2-F1-F0 ) Flame dims from F5 to F1.
F5 is the brightest setting and F0 is off..
Controls the Timer.
9 Settings: (0.5h, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h) Press button
until reach desired setting.
Display Value
Temperature
0 1 2 3 4 5 6 7 8 9 N
18 19
20 21 22 23 24 25 26 27
ON
64 66
68 70 72 74 76 78 80 82
ON
°
C
°
F
HEATER
Controls the Heater.
Press button to initiate the heater.
(H0) no heater or blower.
(BL) blower only.
(H1), heater blows warm air (750W)
(H2), heater blows hot air (1500W)
NOTE
: Heater functions cycle from H0-BL-H1-H2, Press
and hold the heater button for 5s, the heater and
temperature setting will be locked onto the selected
setting. Hold the button for 5s again, the heater will be
unlocked.
1. Press once: Touch panel indicator becomes active.
2. Press again until desired setting is reached. Digital display
shows setting circles as below.
NOTE: Press the button for 5 seconds, the temperature
setting will switch from °C to °F. Same way from °F to °C.
!
WARNING
TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND
CHILDREN. DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY.
KNOT BEFORE THROWING AWAY.
The touch display panel is shown by LED's on the front bottom right of the appliance. The LED's will
disappear after 10 seconds of no function change. The main power button will be dim.
WARNING: Do not move or remove the mesh trim panel when the appliance is plugged in and
operating. This will cause the remote control and touch panel to no longer function.
EN
W415-2172 / A / 11.10.17
19
6.0 MAINTENANCE
!
WARNING
IN PREPARATION FOR MAINTENANCE, ALWAYS DISCONNECT THE POWER AND ALLOW THE
ELECTRIC APPLIANCE TO COOL BEFORE PERFORMING ANY CLEANING, MAINTENANCE OR
RELOCATION OF THIS ELECTRIC APPLIANCE. TURN CONTROLS TO OFF AND REMOVE PLUG
FROM OUTLET OR TURN OFF THE HOUSE CIRCUIT BREAKER TO ELECTRIC APPLIANCE
RECEPTACLE.
DO NOT INSTALL REPLACEMENT LAMPS THAT EXCEED SPECIFIED MAXIMUM WATTS.
THE LED LIGHTS IN YOUR APPLIANCE CAN BECOME HOT. ALLOW AT LEAST 10 MINUTES BETWEEN
TURNING OFF THE APPLIANCE AND REMOVING THE LIGHTS TO AVOID ACCIDENTAL BURNS.
DO NOT HANDLE THE LIGHTS WITH BARE FINGERS, OILS FROM YOUR SKIN WILL DAMAGE THE
LIGHTS WHEN THEY HEAT UP. USE GLOVES OR A CLEAN DRY CLOTH WHEN HANDLING LIGHTS.
6.1 REMOTE BATTERY INSTALLATION
1. To replace the existing battery, remove the
battery holder.
2. To remove the battery holder, turn remote onto
front side and press the left side lever towards
the center while pulling the battery holder out
using the slot provided.
3. Replace existing battery, type CR 2025, with a
new battery and reinstall the battery holder into
the remote by sliding it into position (FIG. 1).
4. Battery cover is secure onto the remote control
when a "CLICKING" noise is heard.
REMOTE
(REAR SIDE)
BATTERY HOLDER
BATTERY (CR 2025)
NOTE: The remote control has a removable plastic tab to prolong the battery life while shipping.
Remove the tab for the remote control to function.
FIG. 1
EN
W415-2172 / A / 11.10.17
20
7.0 WIRING DIAGRAM
!
WARNING
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED
SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

NAPOLEON NEFL42/50/60FH-MT Le manuel du propriétaire

Catégorie
Cheminées
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues