NAPOLEON NEFL42FH-MT Le manuel du propriétaire

EN

W415-2172 / A / 11.10.17

FR

PG

27

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.16G

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleonﬁ replaces.com •[email protected]

SAFETY INFORMATION

!

WARNING

If the information in these instructions

are not followed exactly, a ﬁ re may result

causing property damage, personal injury

or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

$10.00

FOR INDOOR USE ONLY!

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278

NEFL42FH-MT, NEFL50FH-MT &

NEFL60FH-MT

ELECTRIC APPLIANCE

EN

W415-2172 / A / 11.10.17

2

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 4

1.3 GENERAL INSTRUCTIONS 5

1.4 UNPACKING AND TESTING APPLIANCE 5

1.5 HARDWARE PARTS LIST 6

1.6 RATING PLATE INFORMATION 7

2.0 LOCATING APPLIANCE 8

2.1 GROUNDING APPLIANCE 8

3.0 INSTALLATION 9

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 9

3.2 MINIMUM MANTEL CLEARANCES 9

3.3 FRAMING 10

3.4 INSTALLING THE APPLIANCE ONTO THE WALL 11

3.5 RECESSING THE APPLIANCE INTO THE WALL 12

3.6 INSTALLING THE APPLIANCE INTO A MANTEL 13

3.6.1 RUBBER FEET INSTALLATION 14

3.7 HARD WIRING INSTALLATION 15

4.0 FINISHING 16

4.1 MESH TRIM FRONT INSTALLATION 16

4.2 MESH TRIM FRONT REMOVAL 17

4.3 CRYSTAL EMBER INSTALLATION 17

5.0 OPERATING INSTRUCTIONS 18

5.1 MAIN POWER BUTTON 18

5.2 OPERATING TOUCH DISPLAY PANEL AND REMOTE CONTROL 18

6.0 MAINTENANCE 19

6.1 REMOTE BATTERY INSTALLATION 19

7.0 WIRING DIAGRAM 20

8.0 REPLACEMENT PARTS 21

9.0 TROUBLESHOOTING 23

10.0 WARRANTY 24

11.0 NOTES 25

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

Les piles doivent être mises au rebut conformément aux lois et à la réglementation locales.

Certaines piles peuvent être recyclées et acceptées dans votre centre de recyclage local. Rensei-

gnez-vous auprès de votre municipalité au sujet des directives de recyclage.

Las baterías deben desecharse de acuerdo con las leyes y regulaciones locales. Algunas baterías

pueden reciclarse, y es posible que su centro de reciclado local las acepte para desecharlas.

Consulte en su municipalidad sobre las instrucciones para el reciclado.

EN

W415-2172 / A / 11.10.17

3

1.0 INTRODUCTION

!

WARNING

3.7C

C

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed

service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and

other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or

relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

EN

W415-2172 / A / 11.10.17

4

1.1 DIMENSIONS

1.2 LISTING APPROVALS

This appliance has been tested in accordance with the CSA Standards for ﬁxed and location-dedicated

electric room appliances in the United States and Canada. If you need assistance during installation, please

contact your local dealer.

NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in

the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United

States or the Canadian Electric Code, CSA C22.1 in Canada.

Description

Electric Appliance

Type

There are 3 ways to install the unit :

Wall-Mount, Recess into Wall and

Assemble with mantel

Voltage

120V AC

Watts

MAX 1500W

Amps

15 AMP Grounded Circuit

MODEL NO. NET WEIGHT GROSS WEIGHT

NEFL42FH-MT

44.3 lbs (20.1kg) 60.2 lbs (27.3kg)

NEFL50FH-MT

50.9 lbs (23.1kg) 63.4 lbs (29.2kg)

NEFL60FH-MT

61.3 lbs (27.8kg) 73.4 lbs (33.3kg)

A

B

G

F

E

D

C

FRONT VIEW

SIDE VIEW

TOP VIEW

DIMENSIONS

MODEL NO. A B C D E F G

NEFL42FH-MT

42"

(1067mm)

21 5/8"

(550mm)

5 1/3"

(136mm)

20 1/2"

(520mm)

37 1/2"

(951mm)

12"

(304mm)

32 8/16"

(827mm)

NEFL50FH-MT

50"

(1270mm)

21 5/8"

(550mm)

5 1/3"

(136mm)

20 1/2"

(520mm)

45 7/16"

(1154mm)

12"

(304mm)

40 1/2"

(1030mm)

NEFL60FH-MT

60"

(1524mm)

21 5/8"

(550mm)

5 1/3"

(136mm)

20 1/2"

(520mm)

55 5/16"

(1405mm)

12"

(304mm)

50 5/8"

(1287mm)

EN

W415-2172 / A / 11.10.17

5

1.3 GENERAL INSTRUCTIONS

4.8B

A.

Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B.

The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C.

If your appliance does not emit heat, consult the operation section of this manual for further

information.

D.

Use with a CSA- or UL-certiﬁ ed surge protector.

E.

Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

!

WARNING

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

As with most electronic devices, your new electric appliance has been designed to operate at

temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the ﬁreplace

to reach room temperature before turning it on.

1.4 UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the

appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt, 15

Amp grounded outlet.

EN

W415-2172 / A / 11.10.17

6

1.5 HARDWARE PARTS LIST

A - Fireplace

NEFL42FH-60FH-MT (1)

B - Wood Screws

NEFL42FH-50FH-MT (6)

NEFL60FH-MT (12)

C - Drywall Anchors

NEFL42FH-50FH-MT (6)

NEFL60FH-MT (12)

D - ST4x12 Metal Screws

NEFL42FH-60FH-MT (8)

E - Remote Control

NEFL42FH-60FH-MT (1)

F - Wall Bracket

NEFL42FH-50FH-MT (1)

NEFL60FH-MT (2)

G - Crystals

NEFL42FH-60FH-MT (2)

H - Cover Plate

NEFL42FH-60FH-MT (1)

I - Strain Relief

NEFL42FH-60FH-MT (1)

J - Metal Bracket K - Cord Corner

NEFL42FH-60FH-MT (2)

L - Cord Coupler

NEFL42FH-60FH-MT (2)

M - Cord Cover

NEFL42FH-60FH-MT (2)

N - Rubber Foot

NEFL42FH-50FH-MT

NEFL60FH-MT

( 6 )

( 4 )

NEFL42FH-60FH-MT (4)

EN

W415-2172 / A / 11.10.17

7

1.6 RATING PLATE INFORMATION

This illustration is for reference only. Refer to the rating plate on the appliance for accurate

information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

W385-2162

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 2021 / HOMOLOGUÉ SELON

LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 2021

Page 1 of 1

FOYER À ÉLECTRIQUE. HOMOLOGUÉ POUR

INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE

SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR

INSTALLATION DANS UNE MAISON MOBILE.

ELECTRIC FIREPLACE. SUITABLE FOR BEDROOM

AND BED-SITTING ROOM INSTALLATION. SUITABLE

FOR MOBILE HOME INSTALLATION.

VOLTAGE: 120 VAC TENSION: 120VCA

FREQUENCY: 60Hz FRÉQUENCE: 60Hz

POWER: 1500W PUISSANCE: 1500W

DATE CODE: XXXXX CODE DE DATE:

DESIGNED IN NORTH AMERICA

BY WOLF STEEL LTD.

MADE IN CHINA FABRIQUÉ EN CHINE

WOLF STEEL LTD.

24 NAPOLEON ROAD,

BARRIE, ON, L4M 0G8 CANADA

SERIAL NUMBER/NO. DE SÉRIE:

NEFL

MATERIAL: CLASS IIIA-2 PERMANENT LEXAN ADHESIVE LABEL, MINIMUM THICKNESS 0.1MM, 121°C (250°F) RATING

SPECIFICATION: BLACK LETTERING ON SILVER BACKGROUND. MINIMUM FONT SIZE TO BE MINIMUM OF 8.5 PT (3.2mm)

MAX OVERALL SIZE: 6" x 3"

SERIAL NUMBERS TO BE ASCENDING FROM NEFL

TITLE: RATING PLATE NEFL32/42/50/60/72/100FH-MT

REVISION:

DWG#: W385-2162

DATE: 06.22.16

MODELS / MODÈLES

CEFL32FH-MT

DÉSIGN AMÉRIQUE DU NORD

PAR WOLF STEEL LTÉE.

MASTER CONTRACT: 161746

CONTRAT-CADRE: 161746

NEFL32FH-MT

NEFL42FH-MT CEFL42FH-MT

NEFL50FH-MT CEFL50FH-MT

CEFL60FH-MT

NEFL60FH-MT

NEFL72FH-MT

CEFL72FH-MT

NEFL100FH-MT

CEFL100FH-MT

SAMPLE

EN

W415-2172 / A / 11.10.17

8

!

WARNING

2.0 LOCATING APPLIANCE

2.1 GROUNDING APPLIANCE

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

96.1

GROUNDING METHODS

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

This appliance is for use on 120 volts. The cord has a plug

as shown in (A). An adapter as shown in (C) is available for

connecting three-blade grounding type plugs to two-slot

receptacles. The green grounding plug extending from the

adapter must be connected to a permanent ground such as

a properly grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove

plug from outlet.

EN

W415-2172 / A / 11.10.17

9

3.0 INSTALLATION

Your appliance is a wall-mounted, recessed and/or mantel-installed appliance. Select a suitable location that

is not susceptible to moisture and is away from drapes, furniture and high trafﬁc areas.

NOTE: Follow all National and local electrical codes.

!

WARNING

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

68.5A

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

Measurements are taken from the mesh trim front:

Bottom 0" Top 8" (203mm) to mantel

Sides 0" Top 8" (203mm) to ceiling

Back 0"

Side View

8" (203mm)

Mantel

Floor

Wall

!

WARNING

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION. LIGHTER COLOURED PAINTS/LACQUERS

MAY DISCOLOUR.

3.2 MINIMUM MANTEL CLEARANCES

5"

127mm

A

3 1/2"

89mm

MIN

MAX

A

B

Finishing Material

(NON-LOAD

BEARING)

MODEL NO. A B

NEFL42FH-MT 21" (53.5cm) 38" (96.5cm)

NEFL50FH-MT 21" (53.5cm) 45 15/16" (116.6cm)

NEFL60FH-MT 21" (53.5cm) 55 13/16" (141.8cm)

EN

W415-2172 / A / 11.10.17

10

3.3 FRAMING

SIDE VIEW

BODY

MESH TRIM

21 5/8"

550mm

Measurements are taken from the body of the appliance:

Sides, back and top 0"

EN

W415-2172 / A / 11.10.17

11

3.4 INSTALLING THE APPLIANCE ONTO THE WALL

Due to the many different materials used on different walls, it is highly recommended to consult your local

builder before installing this appliance on the wall.

A. Select a location that is not prone to moisture and is located at least 36" (91.4cm) away from

combustible materials such as curtain drapes, furniture, bedding, paper, etc.

B. Have 2 people hold the appliance against the wall to determine the ﬁnal location.

C. Place unit face down on a soft, non abrasive surface. Remove the bracket from the back of the unit

by removing the screws (see illustrations below).

D. Mark out location, then mount the bracket(s) onto the wall using the supplied screws. This bracket

MUST have the hooks facing upward and be level. NOTE: It is strongly recommended that the

mounting bracket be screwed into the wall studs where possible. If the wall studs cannot be

used, ensure that the supplied plastic anchors are used to afﬁx the bracket to the wall and

the bracket is adequately

secured.

E. With the wall mounting bracket

installed, have 2 people lift the

appliance up and insert the

2 hooks on the bracket into

the 2 slots on the back of the

appliance.

F. Check the appliance for stability ensuring that the bracket will not pull free from the wall.

HOOK

SCREWS

HOOK

NEFL42/50FH-MT BRACKET ILLUSTRATED

NEFL60FH-MT BRACKET ILLUSTRATED

Due to the many different ﬁnish materials used on walls, it is highly recommended to consult your local

builder before installing this appliance in the wall.

Select a location that is not prone to moisture and is located at least 36" (91.4cm) away from combustible

materials such as curtain drapes, furniture, bedding, paper, etc.

A. Measure the appliance and create a rough in with electrical.

B. Remove the mesh trim. Refer to "MESH TRIM FRONT REMOVAL" section.

C. Hold the appliance up to ensure it will ﬁt into the framing.

D. If the appliance is fully recessed into the wall:

• Bend the 2 top tabs upward on the mesh trim front (FIG. 3, next page).

• Use the 6 screws (provided) to lock the appliance into the wall with the existing 2 side

ﬂanges (FIG. 1).

• Install the media and reinstall the mesh trim front.

E. If partial recess into the wall:

• Use the 2 mounting brackets (supplied) to lock the appliance to the wall (FIG. 2).

NOTE: 2 sets of holes are provided for recessing into wall. The wall structure may

limit how far the appliance can be recessed. Use the appropriate set of holes when

recessing to the frame, it may be necessary to use the 4 holes on the top and bottom.

NOTE: It is recommended the walls of the appliance enclosure be ﬁnished (ie. drywall) to avoid

exposed insulation or vapour barrier coming in contact with the appliance. This will ensure clearance

to combustibles is maintained.

3.5 RECESSING THE APPLIANCE INTO THE WALL

FIG. 1

FIG. 2

EN

W415-2172 / A / 11.10.17

12

NOTE: The appliance tabs come bent. Tabs must be bent ﬂat by hand when fully recessing the

appliance into the wall (FIG. 4).

A. Remove the mesh trim front. Refer to "MESH TRIM FRONT REMOVAL " section.

B. Install the rubber feet onto the bottom of the appliance for stability. Refer to "RUBBER FEET

INSTALLATION" section.

C. Install the top and bottom brackets provided.

D. Insert the appliance into the mantel and secure it with the brackets, or refer to "ELECTRIC

APPLIANCE MANTEL" installation manual for proper appliance installation instructions.

E. Place the crystal embers along the media tray. Refer to "CRYSTAL EMBER INSTALLATION" section.

F. Reinstall the mesh trim front.

3.6 INSTALLING THE APPLIANCE INTO A MANTEL

FIG. 3

FIG. 4

EN

W415-2172 / A / 11.10.17

13

3.6.1 RUBBER FEET INSTALLATION

A. Place the appliance face down on a soft surface.

B. Using a screw driver, remove the screws on the bottom of the appliance.

C. Install the 4 rubber feet (6 rubber feet for NEFL60FH-MT) onto the bottom of the appliance using the

screws from Step B. See illustrations below.

NOTE: The screws for installing the rubber feet are secured to the appliance. Removal of the screws is

necessary for installing the rubber feet.

NEFL42/50FH-MT ILLUSTRATED

NEFL60FH-MT ILLUSTRATED

EN

W415-2172 / A / 11.10.17

14

3.7 HARD WIRING INSTALLATION

HARD WIRING CONNECTION

If it is necessary to hard wire this appliance, a qualiﬁed electrician must remove the cord connection, and wire

the appliance directly to the house hold wiring.

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired.

In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the

current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

A. Remove the cover plate from the right side

bottom of the appliance by removing the

3 screws (FIG. 1).

B. Remove the wire connectors from the

power cord. The power cord may

be discarded.

C. Locate the new cover plate, supplied in the hardware bag (FIG. 2). Punch out the 7/8" (22.2mm)

hole and install a box connector through, into the junction box. Snap the box connector clamp onto

the supply wires.

D. Using the wire connectors, connect the ground green wires (G) and the common white wires (N)

together, and then the hot black wires (L) (FIG. 3, 4).

E. Reinstall the cover plate using the 3 screws (FIG. 1).

FIG. 1

COVER PLATE

G

N

L

FIG. 2

7/8" (22.2mm)

Diameter

FIG. 3

FIG. 4

EN

W415-2172 / A / 11.10.17

15

EN

W415-2172 / A / 11.10.17

16

4.0 FINISHING

!

WARNING

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

4.1 MESH TRIM FRONT INSTALLATION

!

WARNING

GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.

IF EQUIPPED WITH DOOR LATCHES THAT ARE PART OF A SAFETY RELIEF SYSTEM, THEY MUST BE

PROPERLY ENGAGED. DO NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.

FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR

OPENINGS, LOUVRE OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR

SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.

BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO

THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.

75.1A

!

WARNING

THE DOOR LATCHES ARE PART OF A SAFETY SYSTEM AND MUST BE PROPERLY ENGAGED. DO

NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.

FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR

OPENINGS, LOUVRE OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR

SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.

BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO

THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.

75.1

THIS WARNING FOR ELECTRICS ONLY:

A. Remove the 2 screws from the top of the appliance.

B. Have 2 people lift the mesh trim up and away from the appliance, holding the mesh trim vertical - not

ﬂat - while carrying. Place the mesh trim face down onto a soft, non-abrasive surface, being careful

not to ﬂex the mesh trim.

C. Bend the top tabs ﬂat (FIG. 1).

D. Install the crystal embers. Refer to "CRYSTAL EMBER INSTALLATION" section.

E. Install the mesh trim front by aligning with the pins on the appliance. Press the mesh trim in and down

to securely engage with the brackets. It must be fully engaged to ensure the touch display panel

performs properly.

F. Secure the mesh trim front using the screws provided to the top of the appliance (FIG. 2, next page).

If appliance is fully recessed, this is not necessary.

FIG. 1

EN

W415-2172 / A / 11.10.17

17

FIG. 2

The mesh trim front must be removed and the appliance must be secured in its ﬁnal location before the crys-

tal embers are installed.

A. Carefully place crystal embers into the bottom media tray on

the front of the appliance as illustrated. Apply an even layer

from side to side.

B. Ensure that no crystal embers touch the mesh trim front during

install. Avoid crystal embers scratching/tearing mesh.

A. Remove the 2 screws from the top of the appliance. See illustrations below.

B. Have 2 people lift the mesh trim up and away from the appliance, holding the mesh trim vertical - not

ﬂat - while carrying. Place the mesh trim face down onto a soft, non-abrasive surface, being careful

not to ﬂex the mesh trim.

C. Install the crystal embers. Refer to "CRYSTAL EMBER INSTALLATION" section. Install the front

mesh trim by aligning with the pins on the appliance. This ensures the touch display panel performs

properly.

FOR WALL-MOUNT, PARTIAL-RECESS AND MANTEL-INSTALLED APPLIANCE ONLY:

4.2 MESH TRIM FRONT REMOVAL

4.3 CRYSTAL EMBER INSTALLATION

EN

W415-2172 / A / 11.10.17

18

5.0 OPERATING INSTRUCTIONS

Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.

NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power

failure, the appliance will lose its memory function and will reset to factory mode when the power

returns.

The main power button is located on the front bottom right side of the appliance.

5.1 MAIN POWER BUTTON

5.2 OPERATING TOUCH DISPLAY PANEL AND REMOTE CONTROL

POWER

Turns the appliance ON/OFF.

FLAME - ORANGE

FLAME - BLUE

TIMER

TEMPERATURE

Controls Orange Flame brightness.

6 Settings

: ( F5-F4-F3-F2-F1-F0 ) Flame dims from F5 to F1.

F5 is the brightest setting and F0 is off.

Controls Blue Flame brightness.

6 Settings

: ( F5-F4-F3-F2-F1-F0 ) Flame dims from F5 to F1.

F5 is the brightest setting and F0 is off..

Controls the Timer.

9 Settings: (0.5h, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h) Press button

until reach desired setting.

Display Value

Temperature

0 1 2 3 4 5 6 7 8 9 N

18 19

20 21 22 23 24 25 26 27

ON

64 66

68 70 72 74 76 78 80 82

ON

°

C

°

F

HEATER

Controls the Heater.

Press button to initiate the heater.

(H0) no heater or blower.

(BL) blower only.

(H1), heater blows warm air (750W)

(H2), heater blows hot air (1500W)

NOTE

: Heater functions cycle from H0-BL-H1-H2, Press

and hold the heater button for 5s, the heater and

temperature setting will be locked onto the selected

setting. Hold the button for 5s again, the heater will be

unlocked.

1. Press once: Touch panel indicator becomes active.

2. Press again until desired setting is reached. Digital display

shows setting circles as below.

NOTE: Press the button for 5 seconds, the temperature

setting will switch from °C to °F. Same way from °F to °C.

!

WARNING

TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND

CHILDREN. DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY.

KNOT BEFORE THROWING AWAY.

The touch display panel is shown by LED's on the front bottom right of the appliance. The LED's will

disappear after 10 seconds of no function change. The main power button will be dim.

WARNING: Do not move or remove the mesh trim panel when the appliance is plugged in and

operating. This will cause the remote control and touch panel to no longer function.

EN

W415-2172 / A / 11.10.17

19

6.0 MAINTENANCE

!

WARNING

IN PREPARATION FOR MAINTENANCE, ALWAYS DISCONNECT THE POWER AND ALLOW THE

ELECTRIC APPLIANCE TO COOL BEFORE PERFORMING ANY CLEANING, MAINTENANCE OR

RELOCATION OF THIS ELECTRIC APPLIANCE. TURN CONTROLS TO OFF AND REMOVE PLUG

FROM OUTLET OR TURN OFF THE HOUSE CIRCUIT BREAKER TO ELECTRIC APPLIANCE

RECEPTACLE.

DO NOT INSTALL REPLACEMENT LAMPS THAT EXCEED SPECIFIED MAXIMUM WATTS.

THE LED LIGHTS IN YOUR APPLIANCE CAN BECOME HOT. ALLOW AT LEAST 10 MINUTES BETWEEN

TURNING OFF THE APPLIANCE AND REMOVING THE LIGHTS TO AVOID ACCIDENTAL BURNS.

DO NOT HANDLE THE LIGHTS WITH BARE FINGERS, OILS FROM YOUR SKIN WILL DAMAGE THE

LIGHTS WHEN THEY HEAT UP. USE GLOVES OR A CLEAN DRY CLOTH WHEN HANDLING LIGHTS.

6.1 REMOTE BATTERY INSTALLATION

1. To replace the existing battery, remove the

battery holder.

2. To remove the battery holder, turn remote onto

front side and press the left side lever towards

the center while pulling the battery holder out

using the slot provided.

3. Replace existing battery, type CR 2025, with a

new battery and reinstall the battery holder into

the remote by sliding it into position (FIG. 1).

4. Battery cover is secure onto the remote control

when a "CLICKING" noise is heard.

REMOTE

(REAR SIDE)

BATTERY HOLDER

BATTERY (CR 2025)

NOTE: The remote control has a removable plastic tab to prolong the battery life while shipping.

Remove the tab for the remote control to function.

FIG. 1

EN

W415-2172 / A / 11.10.17

20

7.0 WIRING DIAGRAM

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

La page charge ...

NAPOLEON NEFL42FH-MT Le manuel du propriétaire

Ce manuel convient également à

NAPOLEON NEFL42FH-MT Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents