Samsung WA50N7350AW/A4 Manuel utilisateur

Washing Machine

user manual

WA50M7450A*

WA45M7050A*

WA50N7350A*

WA45N7150A*

imagine the possibilities

Thank you for purchasing this Samsung product.

WA7000M_DC68-03774A-10_EN.indd 1WA7000M_DC68-03774A-10_EN.indd 1 10/15/2020 6:29:56 PM10/15/2020 6:29:56 PM

English - 2

contents

INSTALLING YOUR WASHER

10

10 Unpacking your washer

10 Overview of your washer

11 Basic location requirements

11 Electrical

11 Grounding

11 Water

12 Drain facility

12 Flooring

12 Location considerations

12 Alcove or closet installation

13 Required dimensions for Installation

14 Important note to installer

14 Installation ﬂ ow chart

OPERATING INSTRUCTIONS

18

18 Loading your washer

18 Getting started

WASHING A LOAD OF LAUNDRY

19

19 Overview of the control panel

21 Child Lock [ ]

22 Sound

22 Garment

22 Delay End

22 Pre Soak

23 Mist Shower

23 Smart Care (WA50M7450A*, WA50N7350A*)

24 Washing clothes using the cycle selector

24 ATC (Auto Temperature Control)

25 Prewash (Water Jet)

26 Detergent use

26 Features

MAINTAINING YOUR WASHER

29

29 Cleaning the exterior

29 Cleaning the interior

29 Storing your washer

29 Preserving the top cover and the front frame

29 Cleaning mesh ﬁ lter

30 Cleaning the dispensers (WA45N7150A*,

WA45M7050A*)

31 Cleaning the dispensers (WA50M7450A*,

WA50N7350A*)

32 Self Clean

32 Self Clean reminder

TROUBLESHOOTING

33

33 Check these solutions if your washer…

35 Information codes

APPENDIX

37

37 Fabric care chart

38 Cycle chart

40 Helping the environment

40 Declaration of conformity

40 Speciﬁ cation

WA7000M_DC68-03774A-10_EN.indd Sec6:2WA7000M_DC68-03774A-10_EN.indd Sec6:2 10/15/2020 6:30:09 PM10/15/2020 6:30:09 PM

English - 3

safety information

Congratulations on your new Samsung Washer. This manual contains important

information on the installation, use, and care of your appliance. Please take time

to read this manual to take full advantage of your washer’s many beneﬁ ts and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, and operating your washer.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

To reduce the risk of ﬁ re, explosion, electric shock, or personal injury

when using your washer, follow these basic safety precautions:

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning icons are here to prevent injury to you and others.

Please heed them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

SAVE THESE INSTRUCTIONS

WA7000M_DC68-03774A-10_EN.indd Sec1:3WA7000M_DC68-03774A-10_EN.indd Sec1:3 10/15/2020 6:30:09 PM10/15/2020 6:30:09 PM

English - 4

SAVE THESE INSTRUCTIONS

CALIFORNIA PROPOSITION 65 WARNING

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

IMPORTANT SAFETY PRECAUTIONS

To reduce the risk of ﬁ re, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using the appliance.

2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked

in, or spotted with gasoline, dry-cleaning solvents, other ﬂ ammable or explosive

substances as they give o vapors that could ignite or explode.

3. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

4. Before the appliance is removed from service or discarded, remove the lid of the

washing or drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to the weather.

7. Do not tamper with the controls.

8. Do not repair or replace any part of the appliance or attempt any servicing unless it is

speciﬁ cally recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

9. Do not add gasoline, dry-cleaning solvents, or other ﬂ ammable or explosive substances

to the wash water. These substances give o vapors that could ignite or explode.

10. Under certain conditions, hydrogen gas may be produced in a hot water system that

has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the

hot water system has not been used for 2 weeks or more, before using a washer or

combination washer-dryer, turn on all hot water faucets and let the water ﬂ ow from

each for several minutes. This will release any accumulated hydrogen gas. As the gas is

ﬂ ammable, do not smoke or use an open ﬂ ame during this time.

safety information

WARNING

WA7000M_DC68-03774A-10_EN.indd Sec1:4WA7000M_DC68-03774A-10_EN.indd Sec1:4 10/15/2020 6:30:10 PM10/15/2020 6:30:10 PM

English - 5

CRITICAL INSTALLATION WARNINGS

Plug the power cord into an AC 120 V / 60 Hz/wall socket rated at 15 amps or higher. Use

the socket for this appliance only. In addition, do not use an extension cord.

- Sharing a wall socket with other appliances, using a power strip, or extending the power

cord may result in electric shock or ﬁ re.

- Do not use an electric transformer. It may result in electric shock or ﬁ re.

- Ensure that the power voltage, frequency, and current match the product’s

speciﬁ cations. Failing to do so may result in electric shock or ﬁ re.

Have this appliance installed by a qualiﬁ ed technician or service company.

- Failing to do so may result in electric shock, ﬁ re, an explosion, problems with the

product, or injury.

Remove all foreign substances such as dust or water from the power plug terminals and

contact points using a dry cloth on a regular basis.

- Unplug the power plug and clean it with a dry cloth.

- Failing to do so may result in electric shock or ﬁ re.

Plug the power plug into the wall socket in the right direction so that the cord runs towards

the ﬂ oor.

- If you plug the power plug into the socket in the opposite direction, the electric wires

within the cable may be damaged and this may result in electric shock or ﬁ re.

This appliance must be properly grounded.

Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.

- Improper grounding may result in electric shock, ﬁ re, an explosion, or problems with the

product.

- Never plug the power cord into a socket that is not grounded correctly. Make sure the

socket you use is grounded in accordance with local and national codes.

Do not install this appliance near a heater or ﬂ ammable material.

Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to

direct sunlight or water (rain drops).

Do not install this appliance in a location where gas may leak.

- This may result in electric shock or ﬁ re.

Plug the power plug into the wall socket ﬁ rmly. Do not use a damaged power plug,

damaged power cord, or loose wall socket.

- This may result in electric shock or ﬁ re.

Do not pull or excessively bend the power cord.

Do not twist or tie the power cord.

Do not hook the power cord over a metal object, place a heavy object on the power cord,

insert the power cord between objects, or push the power cord into the space behind the

appliance.

- This may result in electric shock or ﬁ re.

Do not pull the power cord when unplugging the power plug.

- Unplug the power plug by holding the plug.

- Failing to do so may result in electric shock or ﬁ re.

If the power plug or power cord are damaged, contact your nearest service center.

SAVE THESE INSTRUCTIONS

WARNING

WA7000M_DC68-03774A-10_EN.indd Sec1:5WA7000M_DC68-03774A-10_EN.indd Sec1:5 10/15/2020 6:30:10 PM10/15/2020 6:30:10 PM

English - 6

INSTALLATION CAUTIONS

Position the appliance so that the power plug is easily accessible.

- Failing to do so may result in electric shock or ﬁ re due to electric leakage.

Install your appliance on a level and hard ﬂ oor that can support its weight.

- Failing to do so may result in abnormal vibrations, noise, or problems with the product.

Unplug the power plug when the appliance is not being used for long periods of time or

during a thunder/lightning storm.

- Failing to do so may result in electric shock or ﬁ re.

CRITICAL USAGE WARNINGS

If the appliance is ﬂ ooded, cut the power immediately and contact your nearest service

center.

If the appliance emits a strange noise, a burning smell, or smoke, unplug the power plug

immediately and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁ re.

In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area

immediately. Do not turn any appliance or light on or o .

- Do not use a ventilating fan.

- A spark may result in an explosion or ﬁ re.

Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or

other ﬂ ammable or explosive substances.

- This may result in electric shock, ﬁ re, or an explosion.

Do not force the washer lid open while the washer is operating (high-temperature washing/

drying/spinning).

- Water ﬂ owing out of the washer may cause burns or cause the ﬂ oor to be slippery.

This may result in injury.

- Forcing the lid open can damage the product or cause injury.

Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the

washer before using it.

Do not insert your hand under the washer.

- This may result in injury.

safety information

SAVE THESE INSTRUCTIONS

WARNING

CAUTION

WA7000M_DC68-03774A-10_EN.indd Sec1:6WA7000M_DC68-03774A-10_EN.indd Sec1:6 10/15/2020 6:30:10 PM10/15/2020 6:30:10 PM

English - 7

Do not touch the power plug with wet hands.

- This may result in electric shock.

Do not turn the appliance o by unplugging the power plug while the washer is in operation.

- Plugging the power plug into the wall socket again may cause a spark and result in

electric shock or ﬁ re.

Keep all packaging materials well out of the reach of children, as packaging materials can

be dangerous to children.

- If a child places a bag over their head, the child may su ocate.

Do not let children or inﬁ rm persons use this washer unsupervised.

- Failing to do so may result in electric shock, burns or injury.

Do not insert your hand or a metal object under the washer while it is operating.

- This may result in injury.

For waterproof fabrics, only use the WATERPROOF cycle.

- Do not use other cycles for waterproof fabrics. This may result in injury or damage to the

washer, walls, ﬂ oor, or clothing due to abnormal vibrations.

- Set the temperature and spin according to the attached care label.

- WARNING : Failure to closely follow these instructions may result in an abnormal

vibrating and out-of-balance condition that could result in physical injury, property

damage, and/or appliance damage.

Do not attempt to repair, disassemble, or modify the appliance yourself.

- Do not use any fuse (such as copper, steel wire, etc.) other than the standard fuse.

- If you need to repair or reinstall the appliance, contact your nearest service center.

- Failing to do so may result in electric shock, ﬁ re, problems with the product, or injury.

If any foreign substance such as water enters the appliance in any area other than the tub,

unplug the power plug and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁ re.

If the water supply hose comes loose from the faucet and ﬂ oods the appliance, unplug the

power plug.

- Failing to do so may result in electric shock or ﬁ re.

USAGE CAUTIONS

If the washer is contaminated by a foreign substance such as detergent, dirt, food waste,

etc., unplug the power plug and clean the washer using a damp, soft cloth.

- Failing to do so may result in discoloration, deformation, damage or rust.

The clear portion of the lid can be broken by a strong impact. Take care when using the

washer.

- If the clear portion is cracked or broken, it may result in injury.

After a water supply failure or when reconnecting the water supply hose, open the faucet

slowly.

Open the faucet slowly after a long period of non-use.

- The air pressure in the water supply hose or the water pipe may result in damage to a

part or in water leakage.

SAVE THESE INSTRUCTIONS

CAUTION

WA7000M_DC68-03774A-10_EN.indd Sec1:7WA7000M_DC68-03774A-10_EN.indd Sec1:7 10/15/2020 6:30:10 PM10/15/2020 6:30:10 PM

English - 8

If a drain error occurs during an operation, check if there is a draining problem.

- If the washer is used when it is ﬂ ooded because of a draining problem, it may result in

electric shock or ﬁ re due to electric leakage.

Do not insert your hand under the washer.

- This may result in injury.

Insert the laundry into the washer completely so that laundry does not get caught in the lid.

- If laundry gets caught in the lid, it may result in damage to the laundry or the washer, or

result in water leakage.

Ensure that the faucet is turned o when the washer is not being used.

- Ensure that the water supply hose connectors are properly tightened.

- Failing to do so may result in property damage or injury.

Open the faucet and check if the water supply hose connector is ﬁ rmly tightened and that

there is no water leaking before using the product.

- If the water supply hose connectors are loose, it may result in water leakage.

Do not stand on top of the appliance or place objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.

- This may result in electric shock, ﬁ re, problems with the product, or injury.

Do not operate the appliance with wet hands.

- This may result in electric shock.

Do not spray volatile material such as insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may also result in electric shock, ﬁ re, or problems

with the product.

Do not place an object that generates a electromagnetic ﬁ eld near the washer.

- This may result in injury due to a malfunction.

Since the water drained during a high-temperature wash or drying cycle is hot, do not touch

the water.

- This may result in burns or injury.

Do not operate the washer when detergent dispenser is removed.

- This may result in electric shock or injury due to water leakage.

Do not insert your hand into the detergent dispenser after opening it.

- This may result in injury as your hand may be caught.

safety information

SAVE THESE INSTRUCTIONS

WA7000M_DC68-03774A-10_EN.indd Sec1:8WA7000M_DC68-03774A-10_EN.indd Sec1:8 10/15/2020 6:30:10 PM10/15/2020 6:30:10 PM

English - 9

Do not place any non-laundry objects, such as shoes, food waste, or animals into the

washer.

- This can cause abnormal vibrations that can damage the washer, and, in the case of

pets, cause severe injury or death.

Do not press the buttons using sharp objects such as pins, knifes, ﬁ ngernails, etc.

- This may result in electric shock or injury.

Do not wash laundry contaminated by oils, creams, or lotions usually found in skincare

shops or massage clinics.

- This may result in the rubber seal becoming deformed and water leakage.

Do not leave metal objects (safety pins, hair pins, etc.) or bleach in the tub for long periods

of time.

- This may cause the tub to rust.

- If rust appears on the surface of the tub, apply a neutral cleansing agent to the surface

and use a sponge to clean it. Never use a metal brush.

Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry

contaminated by dry cleaning detergent.

- This may result in spontaneous combustion or ignition due to heat from the oxidation of

the oil.

Do not use hot water from water cooling/heating devices.

- This may result in problems with the washer.

Do not use natural hand-washing soap in the washer.

- If it hardens and accumulates inside the washer, it may cause problems with the

product, discoloration, rust, or bad odors.

Do not wash large laundry items such as bedding in the washing net.

- Failing to do so may result in injury due to abnormal vibrations.

- Place smaller items, such as lace socks and lingerie in the washing net.

Do not use hardened detergent.

- If it accumulates inside the washer, it may result in water leakage.

Do not wash throw rugs or doormats.

- If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may

result in error such as no draining.

CRITICAL CLEANING INSTRUCTIONS

Do not clean the appliance by spraying water directly onto it.

Do not use the strong acid cleaning agent.

Do not use benzene, thinner, or alcohol to clean the appliance.

- This may result in discoloration, deformation, damage, electric shock, or ﬁ re.

Before cleaning or performing maintenance, unplug the appliance from the wall socket.

- Failing to do so may result in electric shock or ﬁ re.

SAVE THESE INSTRUCTIONS

WARNING

WA7000M_DC68-03774A-10_EN.indd Sec1:9WA7000M_DC68-03774A-10_EN.indd Sec1:9 10/15/2020 6:30:10 PM10/15/2020 6:30:10 PM

English - 10

installing your washer

Certain internal parts are intentionally not grounded and may present a risk electric shock only during

servicing. Service personnel – Do not contact the following parts while the appliance is energized:

Control board, heat sink, motor, inlet valve, heater and pump.

UNPACKING YOUR WASHER

Unpack your washer and inspect it for shipping damage. Make sure you have received all the items

shown below. If your washer was damaged during shipping, or you do not have all of the items, contact

1-800-SAMSUNG (1-800-726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the washer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

etc.) well out of children’s reach.

When unpacking the washer, 2 person collaboration is

needed. To remove the cushion bottom of the packing

materials, forward dumping is strictly prohibited.

When you lay the washer down to remove carton base, should

protect the side of washer and lay it carefully. Never lay your

washer on its back or front.

OVERVIEW OF YOUR WASHER

Parts supplied

Hose guide User manual book Plastic zip hose tie Water intake cap

Tools needed

Wrench Flat screwdriver Level Adjustable plier Measuring tape

Parts not supplied

• If you lose an accessory and want to purchase a replacement, contact the

Samsung

service center (1-800-SAMSUNG (1-800-726-7864)).

• The design of the parts and accessories may di er from the pictures above. Their design is

subject to change without notice for product improvement.

• Do not reuse old hoses. Only use new water supply hoses when you install the washing

machine. Old water supply hoses can leak or burst causing ﬂ ooding and property damage.

• Conﬁ rm that there are rubber washers inside the couplings of each water supply hoses.

Water supply hoses

Adjustable legs

Drain Hose

Control panel

Lid

Power Cord

WARNING

CAUTION

WARNING

WA7000M_DC68-03774A-10_EN.indd Sec3:10WA7000M_DC68-03774A-10_EN.indd Sec3:10 10/15/2020 6:30:10 PM10/15/2020 6:30:10 PM

English - 11

BASIC LOCATION REQUIREMENTS

Electrical

• 120 Volt 60 Hz 15 AMP fuse or circuit breaker.

• Individual branch circuit serving only your Washer is recommended.

• Your Washer is equipped with a power cord.

NEVER USE AN EXTENSION CORD.

Grounding

ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE.

This appliance must be grounded. In the event of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a power cord having a three-prong grounding plug for use in a

properly installed and grounded outlet.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

An improperly connected equipment-grounding conductor can increase the risk of electrical

shock. Check with a qualiﬁ ed electrician or serviceman if you are not sure whether the

appliance is properly grounded. Do not modify the plug provided with the appliance – if it

does not ﬁ t the outlet, have a proper outlet installed by a qualiﬁ ed electrician.

IMPORTANT SAFETY PRECAUTIONS

• To prevent unnecessary risk of ﬁ re, electrical shock or personal injury, all wiring and

grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.

70 Latest Revision and local codes and ordinances. It is the personal responsibility of the

appliance owner to provide adequate electrical service for this appliance.

NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR

HOT WATER PIPES.

Water

To correctly ﬁ ll your Washer in the proper amount of time, water pressure of 20 to 116psi (137 to

800kPa) is required.

Water pressure less than 20 psi may cause water valve failure, or may not allow the water valve

to shut o completely, or may extend the ﬁ ll time beyond what your Washer controls allow,

causing your Washer to turn o . A time limit is built into the controls to prevent ﬂ ooding in your

home if a hose becomes loose.

The water faucets must be within 4 feet / 122 cm of the back of your Washer to match the inlet

hoses provided with your Washer.

Accessory inlet hoses are available in various lengths up to 10 feet / 275 cm for faucets that

are further away from the back of your Washer.

To avoid the possibility of water damage:

• Have water faucets easily accessible.

• Turn o faucets when the washer is not in use.

• Periodically check that there is no leakage from the water inlet hose ﬁ ttings.

CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.

01 installing your washer

CAUTION

WARNING

CAUTION

WARNING

WA7000M_DC68-03774A-10_EN.indd Sec3:11WA7000M_DC68-03774A-10_EN.indd Sec3:11 10/15/2020 6:30:11 PM10/15/2020 6:30:11 PM

English - 12

Drain facility

The recommended height of the standpipe is 39 in / 99 cm. The drain hose must be routed

through the drain hose clip to the standpipe. The standpipe must be large enough to accept the

outside diameter of the drain hose. The drain hose is attached to the washer at the factory.

Flooring

For best performance, you must install your washer on a solidly constructed ﬂ oor. Wood ﬂ oors

may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting

and soft tile surfaces are contributing factors to vibration which can cause your washer to move

slightly during the spin cycle.

Never install your washer on a platform or weakly supported structure.

Location considerations

Do not install your washer in areas where water may freeze, since your washer will always retain

some water in its water valve, pump, and hose areas. Frozen water can damage the belts, the

pump, hoses, and other components.

Alcove or closet installation

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm

Rear – 5.9 in / 150 mm

Closet Front – 1 in / 25 mm

TOP - 21 in / 533 mm

Gap between end of water valve and the wall

- Case 1. Assemble supply hose after installing : Over 3.9 in (10 cm).

- Case 2. Assemble supply hose before installing : Over 2.8 in (7cm).

If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²)

unobstructed air opening. Your washer alone does not require a speciﬁ c air opening.

A. Recessed area

B. Side view - closet or conﬁ ned area

installing your washer

1 in.

(2.5 cm)

5.9 in.

(15.0 cm)

29.3 in.

(74.4 cm)

B

21 in.

(53.3 cm)

Case 1. 3.9 in. (10 cm)

Case 2. 2.8 in. (7 cm)

A

1 in.

(2.5 cm)

1 in.

(2.5 cm)

27.0 in.

(68.6 cm)

27.0 in.

(68.6 cm)

1 in.

(2.5 cm)

WA7000M_DC68-03774A-10_EN.indd Sec3:12WA7000M_DC68-03774A-10_EN.indd Sec3:12 10/15/2020 6:30:11 PM10/15/2020 6:30:11 PM

English - 13

Required dimensions for Installation

WA45M7050A*, WA45N7150A*

27.0 in.

(68.6 cm)

43.9 in.

(111.5 cm)

39.3 in.

(99.8 cm)

29.3 in.

(74.4 cm)

29.3 in.

(74.4 cm)

43.9 in.

(111.5 cm)

58.1 in.

(147.6 cm)

Closet or Door

48 in.² *

(310 cm²)

24 in.² *

(155 cm²)

3 in.

(7.6 cm)

3 in.

(7.6 cm)

*Required spacing

WA50M7450A*, WA50N7350A*

27.0 in.

(68.6 cm)

45.0 in.

(114.4 cm)

40.2 in.

(102.2 cm)

29.3 in.

(74.4 cm)

29.3 in.

(74.4 cm)

45.0 in.

(114.4 cm)

59.0 in.

(150.0 cm)

Closet or Door

48 in.² *

(310 cm²)

24 in.² *

(155 cm²)

3 in.

(7.6 cm)

3 in.

(7.6 cm)

*Required spacing

01 installing your washer

WA7000M_DC68-03774A-10_EN.indd Sec3:13WA7000M_DC68-03774A-10_EN.indd Sec3:13 10/15/2020 6:30:11 PM10/15/2020 6:30:11 PM

English - 14

installing your washer

IMPORTANT NOTE TO INSTALLER

Please read the following instructions carefully before installing your washer.

These instructions should be retained for future reference.

We recommend you hire a professional to install this washer.

Installation ﬂ ow chart

STEP 1 Selecting a Location

Before you install the washer, make sure the location:

• Has a hard, level surface without carpeting or ﬂ ooring that may obstruct ventilation.

• Is away from direct sunlight.

• Has adequate ventilation.

• Is not exposed to freezing temperatures (temperatures under 32 °F or 0 °C).

• Is away from heat sources such as oil or gas.

• Has enough space so that the washer doesn’t rest on its power cord.STEP 2

Connecting the water and the drain

Connecting the water supply hose

Before installing the water supply hoses, make sure there are

rubber gaskets inside the ﬁ ttings at both ends of each new

water hose. Installing the water supply hoses without rubber

gaskets can cause water leakage.

When you initially install the washer, be sure to use new hoses.

Failing to do so may result in a water leakage or overﬂ ow and

may damage your property.

Do not connect multiple water supply hoses together to

increase the length of the supply hose. Hoses connected this

way can leak and the leakage can cause electrical shock. If a

hose is too short, replace the hose with a longer, high pressure

hose.

Selecting

a location

Removing the

shipping bolts

(*Drum only)

Adjusting the

levelling feet

Connecting the water

and the drain

[Running a test cycle]

Run a test cycle(Rinse+Spin)

with small amount of laundary

(about 4~5 Towels)

Running

a Calibration

mode

Powering your

washing machine

Finish the

installation

Does a

Laundary machine

Vibrate?

No

Yes

Please check again before steps.

Rubber Washer

Coupling

CAUTION

WA7000M_DC68-03774A-10_EN.indd Sec3:14WA7000M_DC68-03774A-10_EN.indd Sec3:14 10/15/2020 6:30:11 PM10/15/2020 6:30:11 PM

English - 15

1. Connect the ends of the water supply hoses to the HOT and COLD

faucets.

2. Tighten the ﬁ ttings by hand until they are snug, and then tighten them an

additional two-thirds of a turn with a plier.

When you fasten the ﬁ ttings, do not fasten them too tightly or apply

tape or sealant to the faucets or water supply intakes. This can

damage the ﬁ ttings.

After you have connected the water supply hoses to the faucets,

ensure that they are connected correctly by pulling the water supply

hoses downwards

3. Place the unconnected ends of the hoses into a bucket and open the

faucets connected to the two water supply hoses for 10 or 15 seconds to

remove any foreign substances from the hoses. Close the faucets before

continuing.

4. Connect the ends of the water supply hoses to the water supply intake

connections at the back of the washer.

The water supply hose connected to the HOT faucet must be

connected to the hot water supply intake and the water hose

connected to the COLD faucet must be connected to the COLD

water supply intake.

5. Tighten the ﬁ ttings by hand until they are snug, and then tighten them

an additional two-thirds of a turn with a plier.

To ensure the correct water usage, connect both the HOT and

COLD water faucets. If either or both are not connected, an “4E”

(no ﬁ ll) error can occur.

If you do not want to use the HOT water supply hose, insert

the water intake cap into the HOT water supply intake hole. In

this case, you must select the Tap Cold option for the water

temperature. If you select the Tap Cold option, all the lamps for

the water temperature options are turned o .

Conﬁ rm that the water supply hoses are not twisted or bent. If the

hoses are twisted or bent, the hoses can leak and cause electric

shock due to the water leakage.

6. Turn on the HOT and COLD water supplies and check all the water

supply intake connections and the faucets for water leaks.

01 installing your washer

CAUTION

WA7000M_DC68-03774A-10_EN.indd Sec3:15WA7000M_DC68-03774A-10_EN.indd Sec3:15 10/15/2020 6:30:12 PM10/15/2020 6:30:12 PM

English - 16

installing your washer

Connecting the drain hose

The end of the drain hose can be positioned in three ways:

In a Wall standpipe or Floor standpipe

The height of end of standpipe must be no lower than 39 in (99 cm) and no

higher than 96 in (245 cm).

If drain pipe are built into the wall with water valves (A), fasten the drain hose

to the water hose.

Make sure that the connection between the drain hose and the

standpipe is not airtight.

In a laundry tub

The height of the tub must be no lower than 39 in (99 cm) and no higher than

96 in (245 cm).

Assemble the supplied Hose guide at the end of the drain hose, and put the

hanger on laundry tub.

And fasten the drain hose to the leg of laundry tub.

Connect the hose guide (A) within 3~5 in (7.6~12.7 cm)* from the end of

the drain hose. If the drain hose is extended beyond the end of the hose

guide, mold or microorganisms could spread inside the washer.

Drain Hose can be installed until 96 in (245cm) maximum. But drain

capability can be reduced at this height. It causes the washer to have

odor, because of remained water in the drain system.

If the drain hose is installed below 39 in (99 cm), water can be drained in cycles due to a

siphon phenomenon. It causes the washer to display a “4E” error code.

STEP 3

Leveling your washer

See if the washer is level by checking the position of the tub:

1. Slide the washer into position.

2. Open the lid of the washer, and pour the water into the tub to

just below the pulsator level.

3. If the washer is level, the pulsator is positioned at the center of the

water as shown in the ﬁ gure. If not, level your washer by turning the

front leveling feet clockwise or counterclockwise as necessary.

Turn the front leveling feet clockwise to raise the washer, and

counterclockwise to lower the washer.

The number of leveling feet di ers with the model.

A

*

A

Loosen Lock

Pulsator

Adjustable legs

(three)

WA7000M_DC68-03774A-10_EN.indd Sec3:16WA7000M_DC68-03774A-10_EN.indd Sec3:16 10/15/2020 6:30:12 PM10/15/2020 6:30:12 PM

English - 17

STEP 4

Powering your washer

Plug the power cord into a 3-prong, well grounded 120 volt 60

Hz approved electrical outlet protected by a 15-amp fuse or

comparable circuit breaker.

Your washer is grounded through the third prong of the power

cord when plugged into a three-prong grounded electrical

outlet.

Test run

Make sure that you install your washing machine correctly by running the Rinse+Spin cycle

after the installation is complete.

STEP 5

Running a test cycle

Run a test cycle as follows to check if your washer is properly installed.

1. Load about 6 pounds of laundry into the tub.

2. Press the Power button to turn on your washer.

3. Select the Rinse+Spin cycle by turning the Cycle Selector.

4. Press the Start/Pause button to start the test cycle.

5. The washer should not rock or vibrate excessively when water is supplied or when washing

or spinning, and should drain well during the spin cycle.

If water leaks while water is being supplied or drained, check the water connections. Refer

to the “Connecting the water and the drain” section on pages 14~15 for instructions.

If the washer rocks and vibrates excessively, level your washer again. Refer to the “Leveling

your washer” section on page 15 for instructions.

STEP 6

Calibration mode

Your Samsung washer detects the laundry weight automatically.

For more accurate weight detection, please run Calibration Mode after the installation.

To run Calibration Mode, follow these steps:

1. Remove laundry or any contents in the machine.

2. Press and hold Temp. and Delay End simultaneously for at least 3seconds when the power

is turned on.

3. Press START/PAUSE to activate Calibration Mode.

4. The pulsator rotates clockwise and counterclockwise approximately 1minute.

5. When Calibration Mode is ﬁ nished, “0” appears on the display, and the washer automatically

turns o . The washer is now ready for use.

01 installing your washer

WA7000M_DC68-03774A-10_EN.indd Sec3:17WA7000M_DC68-03774A-10_EN.indd Sec3:17 10/15/2020 6:30:13 PM10/15/2020 6:30:13 PM

English - 18

operating instructions

WARNING: To reduce the risk of ﬁ re, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

LOADING YOUR WASHER

• Fill the tub with dry, unfolded clothes evenly around in order to enhance washing e ciency and prevent

excess wear, or wrinkling of the load.

- For optimal washing performance, make sure the laundry is piled up evenly.

• Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle

with similar lightweight items.

• When washing big bulky items or a few smaller items that don’t ﬁ ll the tub

completely – a rug, a pillow, stu ed toys, or one or two sweaters, for example –

add a few towels to improve spin performance.

• Do not insert bulky items except for Bedding in this cycle.

During the spin cycle, the washer may add additional water to redistribute the clothes and correct an

imbalance inside the drum.

• When washing heavily soiled loads, do not overload your washer to ensure good cleaning results.

• Inﬂ atable items may cause damage to the laundry or the machine during the wash or drying

process.

• Regardless of the size, blankets or quilts are safer and cleaner to wash one item at a time.

Two di erent-sized blankets in the same load may compromise the drying performance due to

unbalanced loads.

To input a blanket

Fold the blanket into the blanket-speciﬁ c net as shown, and then insert in the tub below the plastic

area of the tub.

Make sure the laundry is inserted completely.

• Any exposed part of the laundry may cause damage to the machine or the laundry itself, or a water

leak.

• Do not overload the tub. Make sure no part of the laundry is exposed outside of the tub.

To add a forgotten item:

1. Press the Start/Pause button to pause the washer.

2. Wait for the door to unlock automatically, and then open the door.

3. Add the item, close the door, and then press the Start/Pause button. The cycle will resume.

GETTING STARTED

1. Load your washer.

2. Add liquid (or powder) detergent and additives to the dispenser (see pages 24~26).

3. Select the appropriate cycle and options for the load (see pages 18~23).

4. Close the lid.

5. Press the Start/Pause button.

6. The Wash Indicator light illuminates.

7. The estimated cycle time will appear in the display.

The time may ﬂ uctuate to indicate the time remaining in the cycle better.

The actual time required for a cycle may di er from the estimated time in the display depending on the

water pressure, water temperature, detergent, and laundry.

8. Before your washer starts to ﬁ ll, it will make a series of clicking noises to check the door lock and do a

quick drain.

• When the cycle is complete, the Door Lock light will go out and “End” (WA50M7450A*,

WA50N7350A*) / “0” (WA45M7050A*, WA45N7150A*) will appear in the display.

• Pressing the Power button cancels the cycle and stops your washer.

•

The Wash, Rinse , and Spin indicator lights will illuminate during those portions of the cycle.

WARNING

WA7000M_DC68-03774A-10_EN.indd 18WA7000M_DC68-03774A-10_EN.indd 18 10/15/2020 6:30:14 PM10/15/2020 6:30:14 PM

English - 19

washing a load of laundry

OVERVIEW OF THE CONTROL PANEL

Cycle Selector

Select the appropriate cycle for the type of load.

The cycle you select determines the tumble pattern and spin speed for the

cycle.

To minimize wrinkling of laundry, select the PERM PRESS cycle.

NORMAL - For most fabrics including cottons, linens, and normally soiled

garments.

HEAVY DUTY - For sturdy, colorfast fabrics and heavily soiled garments.

BRILLIANT WHITES (WA50M7450A*, WA50N7350A*)

- For white

fabrics with or without bleach.

BEDDING/WATERPROOF - For bulky and large items, such as

comforters, blankets and sheets. When washing comforters, use liquid

detergent, waterproof or water-resistant items.

 Do not wash waterproof items and non-waterproof items together.

 Check the speciﬁ cation label on the fabric item and see if the item is

waterproof.



Use the bedding/waterproof cycle for waterproof or water-resistant items

such as plastic mats, ski pants, raincoat and comforters which hardly

absorb water.

DEEP WASH

- Use more water in washing and rinsing.

DELICATES - For sheer fabrics, bras, lingerie, silks, and other handwash-

only fabrics. For best results, use liquid detergent.

03 washing a load of laundry

WA45M7050A*, WA45N7150A*

WA50M7450A*, WA50N7350A*

4

3 5

1 6

7

8

2

1

WA7000M_DC68-03774A-10_EN.indd 19WA7000M_DC68-03774A-10_EN.indd 19 10/15/2020 6:30:14 PM10/15/2020 6:30:14 PM

English - 20

PERM PRESS - For wash-and-wear, synthetic fabrics, and lightly to normally

soiled garments.

ACTIVE WEAR (WA50M7450A*, WA50N7350A*) - Use this cycle to wash exercise

wear such as sports jerseys, training pants, shirts/tops and other performance

clothing. This cycle provides e ective soil removal with gentle action for special

fabric care.

QUICK WASH - For lightly soiled garments needed quickly.

SPIN - Drains the water and spins at a high speed.

RINSE + SPIN - Use for loads that need rinsing only or to add rinse-added

fabric softener to a load.

Display

Provides instructions and diagnostics while keeping you updated on the cycle

status and time remaining.

Temp. selection

button

Press the button repeatedly to cycle through the di erent water temperature options.

Hot - Whites and heavily soiled, colorfast items.

Warm - Colorfast items.

Eco Warm - Moderately soiled, colorfast items; most wrinkle-free items.

Cool - Brightly colored, very lightly soiled items.

Cold - Cold water with no warm water added.

 If you select the Cold option, all the lamps for the water temperature options

are turned o .

Spin selection

button

Press the button repeatedly to cycle through the di erent spin speed options.

High - Use for underwear, t-shirts, jeans, and sturdy cottons.

Medium - Use for jeans, wrinkle-free or wash-and-wear items, and synthetics.

Low - Use for delicate items needing a slow spin speed.

No Spin - Drains your washer without spinning. Use for extremely delicate items

that cannot tolerate any spin.

Soil Level

selection button

Press the button to select the soil level/washing time.

Heavy - For heavily soiled loads.

Normal - For moderately soiled loads. This setting is best for most loads.

Light - For lightly soiled loads.

Select Cycle

Option

Press these buttons to select di erent cycle options.

Extra Rinse - Change from spray rinse mode to deep rinse mode, and rinse once

again.

Delay End - Delay the end of any cycle for up to 19 hours in one-hour increments.

Displayed hour indicates the time the wash will be ended.

Self Clean - Use to clean dirt and bacteria from the drum. Regular use (after every

40 washes) is recommended.

Pre Soak - It adds 15 minutes soaking time at the start of the wash cycle for

better stain removal.

Start/Pause

selection button

Press to pause and restart cycles.

Power button

Press once to turn your washer on. Press again to turn your washer o . If the

washer is left on for more than 10 minutes without any buttons being pressed, the

power automatically turns o .

2

3

4

5

6

8

7

washing a load of laundry

WA7000M_DC68-03774A-10_EN.indd 20WA7000M_DC68-03774A-10_EN.indd 20 10/15/2020 6:30:14 PM10/15/2020 6:30:14 PM

La page charge ...

Samsung WA50N7350AW/A4 Manuel utilisateur

Samsung WA50N7350AW/A4 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents