BOB Duallie Manuel utilisateur

Catégorie
Poussettes
Taper
Manuel utilisateur
P637400A
eaBOB G r by Britax (888) 427-4829 or (704) 409-1699
4140 Pleasant Road, Fort Mill, South Carolina, 29708
www.bobgear.com
READ INSTRUCTIONS COMPLETELY!
LIRE CES INSTRUCTIONS COMPLETEMENT!
¡LEA INSTRUCCIONES COMPLETAMENTE!
Si tiene dudas sobre algún punto, contacte con su distribuidor o
con BOB Gear by Britax antes de usar el producto. Para obtener
una lista de distribuidores, visite www.bobgear.com o llame al
(888) 427-4829 o al (704) 409-1699.
Pour toute question, contactez votre revendeur ou BOB Gear by
Britax avant toute utilisation. Pour une liste des
revendeurs, rendez-vous sur www.bobgear.com ou composez
le (888) 427-4829 ou (704) 409-1699.
If you are unclear on any point, contact your authorized dealer
or BOB Gear by Britax Customer Service before use. For a list
of dealers, visit www.bobgear.com or call (888) 427-4829 or
(704) 409-1699.
®®
INFANT CAR SEAT ADAPTER FOR
PEG PEREGO
ADAPTATEUR DE SIÈGE DE VOITURE
POUR ENFANT PEG PEREGO
ADAPTADOR DE ASIENTO DE COCHE
PARA BEBÉ PEG PEREGO
ENGLISH
FRANÇAIS
ESPANOL
INSTRUCTIONS
Duallie
®
Strollers
Poussettes Duallie
®
Cochecitos Duallie
®
2
P637400A
WARNING
• Do not use off-road or on uneven terrain when using the Infant
Car Seat Adapter with Infant Car Seat installed. Doing so may
cause the stroller to become unstable and tip resulting in
serious injury.
• Avoid serious injury from falling or sliding out. Always use Infant
Car Seat harness.
• Do not modify the Infant Car Seat Adapter or remove any
labels. Doing so voids the warranty and could lead to a
dangerous condition.
• Care must be taken when folding and unfolding the stroller to
prevent finger entrapment or injury.
• Always follow the Infant Car Seat manufacturer’s instructions.
Do not exceed the Infant Car Seat manufacturer’s instructions
for maximum load carrying capacity of the Infant Car Seat.
Exceeding carrying capacity may cause the stroller to become
unstable and tip resulting in serious injury.
• Do not run or jog when using Infant Car Seat Adapter with
Infant Car Seat. Exceeding carrying capacity may cause the
stroller to become unstable and tip resulting in serious injury.
FAILURE TO FOLLOW THESE WARNINGS AND
ASSEMBLY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
3
P637400A
CONGRATULATIONS
Congratulations on your purchase of the BOB Infant Car Seat Adapter (ICSA).
It is designed to allow the attachment of an Infant Car Seat to a BOB stroller.
Please refer to chart on page 5 for details of compatible ICSA models and
Infant Car Seats. Find key features of your ICSA on Anatomy pages and follow
respective instructions.
For updates to this manual, warranty and other recent product notifications,
Please visit www.bobgear.com periodically or any time before making approved
changes or adding approved equipment to your stroller.
Please save instructions for future use and reference.
For safe operation, all users must read instructions and warnings
completely before use.
The BOB
®
Infant Car Seat Adapter (ICSA) is designed for use with BOB
Strollers equipped with Accessory Adapters and compatible Infant
Car Seats. This product is not a universal adapter. Do not use with car
seat models other than those specifically listed in the Infant Car Seat
Compatibility Chart on page 5.
Never leave children unattended in the stroller/Infant Car Seat.
Always keep your Infant Car Seat Carry Handle locked in the vertical/carry
position while in stroller, as extra protection for your child.
Always confirm Infant Car Seat Adapter is properly locked in place in
stroller Accessory Adapters prior to use.
Always secure the Infant Car Seat to the Infant Car Seat Adapter with the
supplied Restraint Belt.
Remove Infant Car Seat Adapter and Restraint Belt when not in use.
Do not place children directly in the stroller seat with the Infant Car Seat
Adapter installed. Remove Infant Car Seat Adapter from stroller prior to
placing a child directly into the stroller seat.
Restraint Belt is intended for use with combination of BOB Infant Car Seat
Adapter and compatible Infant Car Seats only. The Restraint Belt must be
removed prior to using stroller without Infant Car Seat.
Care must be taken when attaching Infant Car Seat to Infant Car Seat
Adapter to make sure hands and fingers are clear of contacting surfaces.
IMPORTANT NOTES
4
P637400A
TABLE OF CONTENTS
Warnings ......................................................................................................... 2
Important Notes ............................................................................................. 3
Table of Contents ............................................................................................ 4
Compatibility Chart ......................................................................................... 5
S924600 ICSA Peg Perego
Primo Viaggio
4.35 Anatomy ............................ 6
CS1107 ICSA for Peg Perego Primo Viaggio SIP Anatomy ........................... 6
Peg Perego Primo Viaggio 4.35 Infant Car Seat Anatomy ............................ 7
Peg Perego Primo Viaggio SIP Infant Car Seat Anatomy .............................. 7
Stroller Accessory Adapter Anatomy ............................................................. 8
Restraint Belt Anatomy ................................................................................... 8
Canopy Catch Anatomy .................................................................................. 8
Installing Your ICSA ......................................................................................... 9
Attaching Restraint Belt ............................................................................................. 9
Installing Canopy Catch ..........................................................................................10
Attaching ICSA to Stroller ............................................................................ 10
Preparing Stroller for ICSA ......................................................................................10
Installing ICSA ...........................................................................................................11
Preparing to Attach Infant Car Seat ............................................................. 11
Infant Car Seat Installation ............................................................................ 12
S924600 ICSA Peg Perego Primo Viaggio 4.35, SIP & SIP 30/30 ......................12
CS1107 ICSA Peg Perego Primo Viaggio SIP & SIP 30/30 ................................. 13
Securing Restraint Belt ................................................................................. 14
Removing Infant Car Seat from Stroller ...................................................... 14
Folding Stroller with ICSA Attached ............................................................ 15
Removing ICSA from Stroller ........................................................................ 15
Removing Restraint Belt from Stroller .......................................................... 16
Limited Warranty .......................................................................................... 17
Instructions en français ................................................................................. 18
Instrucciones en español ............................................................................... 34
BOB
®
, BOB Gear
®
, BRITAX
®
and DUALLIE
®
are trademarks owned by Britax and
registered in the U.S.A. and other countries. All Rights Reserved.
This product and its components are subject to change without notice.
5
P637400A
COMPATIBILITY CHART
INFANT CAR SEAT COMPATIBILITY CHART
BOB ICSA Model Infant Car Seat Brand Infant Car Seat Model
Primo Viaggio SIP
Primo Viaggio SIP 30/30
CS1107 - Duallie Peg Perego
Primo Viaggio 4.35
Primo Viaggio SIP
Primo Viaggio SIP 30/30
S924600 - Duallie Peg Perego
IMPORTANT:
Compatible with all BOB DUALLIE Strollers featuring the
Accessory Adapter. This product is not a universal adapter. Do
not use with car seats other than those specifically listed in
the Infant Car Seat Compatibility Chart. Please reference www.
bobgear.com/carseatadapter for additional compatibility
information.
6
P637400A
S924600 ICSA FOR PEG PEREGO PRIMO VIAGGIO 4.35 ANATOMY
Remove ICSA from packaging. Please dispose of packaging material properly,
recycle if possible.
NOTE: Note key features of each product. Instructions refer to these features
by name.
Front Tube
Locking End Cap
Locking End Cap Latch Tube
Snack Tray
ANATOMY
CS1107 ICSA
FOR PEG PEREGO PRIMO VIAGGIO SIP ANATOMY
Remove ICSA from packaging. Please dispose of packaging material properly,
recycle if possible.
NOTE: Note key features of each product. Instructions refer to these features
by name.
Front Tube
Locking End Cap
Locking End Cap Latch Tube
Snack Tray
7
P637400A
Carry Handle
Carry Handle
Release Handle
Latch Feature
Harness
Groove Feature
PEG PEREGO PRIMO VIAGGIO SIP INFANT CAR SEAT ANATOMY
NOTE: Primo Viaggio SIP model shown, similar features exist on all compatible
Peg Perego
Primo Viaggio SIP models (see Compatibility Chart Page 5).
NOTE: Note key features of each product. Instructions refer to these features
by name.
Carry Handle
Carry Handle
Release HandleLatch Feature
Harness
Groove Feature
NOTE: Primo Viaggio 4.35 model shown (see Compatibility Chart Page 5).
NOTE: Note key features of each product. Instructions refer to these features
by name.
PEG PEREGO PRIMO VIAGGIO
4.35 INFANT CAR SEAT
ANATOMY
8
P637400A
STROLLER ACCESSORY ADAPTER ANATOMY
RESTRAINT BELT ANATOMY
CANOPY CATCH ANATOMY
Red Ring
Buckle (Male)
Buckle (Female)
Captured Screws
Receiver
Socket
Cover
Red Release
Button
Anchor Nut
DUALLIE - Accessory Adapters
Anchor Nut
DUALLIE - Center Canopy Mount
Screw
Canopy Catch Clamp
9
P637400A
INSTRUCTIONS
INSTALLING YOUR ICSA
ATTACHING RESTRAINT BELT
NOTE: Thread the Captured Screw
with Buckle (Female) completely into
Anchor Nut on left side of Center
Canopy Mount (center of stroller
between seats) and tighten firmly.
1. Prepare Stroller
Set parking brake, rotate canopy
towards handlebar (see stroller
owner’s manual if necessary).
2. Install Restraint Belt with
Screwdriver
Using a screwdriver, thread the
Captured Screw with Buckle (Male)
completely into Anchor Nut on right
seated side of stroller Accessory
Adapter and tighten firmly.
Confirm each Captured
Screw is threaded fully into,
and tightened firmly against,
each Anchor Nut. Failure to
properly secure Restraint
Belt may result in accident,
injury, or death.
Duallie
Center
Anchor
Nut
10
P637400A
Left
Canopy
Right
Canopy
4. Secure Right Canopy
Rotate right canopy back (toward
handlebar). Slide right canopy stay
under Canopy Catch. Pull on canopy
to verify that Canopy Catch securely
holds canopy in place.
Canopy Catch
Cross Strap
Webbing
Canopy Catch
Right Canopy
Stay
ATTACHING ICSA TO STROLLER
PREPARING STROLLER FOR ICSA
1. Prepare Stroller
Set parking brake, rotate canopy
towards handlebar (see stroller
owner’s manual if necessary).
Cross Strap
Webbing
Canopy
Catch
Failure to attach ICSA
securely to stroller may result
in serious injury or death.
INSTALLING CANOPY CATCH
1. Rotate Canopies
Rotate both canopies forward to
expose Cross Strap Webbing.
3. Secure Canopy Catch
Hold Canopy Catch in place and
tighten screw with screwdriver.
2. Locate Canopy Catch
Slide Canopy Catch over cross
strap webbing - making sure Clamp
portion is centered between the left
and right canopies.
Right
Canopy Stay
Left
Canopy Stay
11
P637400A
1. Prepare Stroller
Set parking brake, rotate canopy towards
handlebar, place Restraint Belt ends to
the sides of stroller seat.
2. Place Infant Into Infant Car Seat
Fasten harness securely (see Infant Car
Seat owner’s manual if necessary).
3. Position Infant
Car Seat Carry
Handle
Move Infant Car
Seat Carry Handle
into upright
position.
INSTALLING ICSA
3. Slide Covers Down
Push to slide each Cover (at front of
stroller Accessory Adapters) down
on each side of stroller, exposing
each Receiver Socket.
1. Align Locking End Caps
Align and insert each Locking End
Cap on ICSA into each respective
Accessory Adapter Receiver
Socket.
2. Verify Proper Installation
Pull on center of ICSA Front
Tube to verify ICSA is securely
locked into place.
CLICK
CLICK
2. Unfasten Restraint Belt Buckle
Unfasten buckle of Restraint Belt and
place buckle ends to the
sides of stroller seat.
PREPARING TO ATTACH
INFANT CAR SEAT
Failure to securely attach
Infant Car Seat and properly
secure infant with seat
harness of Infant Car Seat
may result in accident,
serious injury or death.
NOTE: When attaching Infant
Car Seat to ICSA for the first time,
practice attaching and removing
unoccupied Infant Car Seat several
times until the function becomes
familiar.
12
P637400A
CLICK
CLICK
1. Prepare Stroller
Set parking brake, rotate canopy
towards handlebar, place Restraint Belt
ends to the sides of stroller seat (see
stroller owner’s manual if necessary).
2. Align Infant Car Seat
Place Infant Car Seat “rear facing”
directly centered on top of ICSA,
align Groove Feature on Infant Car
Seat with Middle Tube on ICSA.
3. Verify Infant Car Seat is Latched
Properly
Push Infant Car Seat straight down
onto ICSA until the adapters on each
side lock into the receivers on ICSA.
4. Verify Infant Car Seat is
Securely Attached
Pull up to ensure the Infant Car
Seat is secure.
5. Secure Restraint Belt
Proceed to section titled “Securing
Restraint Belt” (pg.14).
Failure to properly secure
Restraint Belt and to properly
install Infant Car Seat on Infant
Car Seat Adapter may result
in accident, injury or death.
INFANT CAR SEAT
INSTALLATION
S924600 ICSA PEG PEREGO
PRIMO VIAGGIO 4.35,
SIP & SIP 30/30
13
P637400A
CLICK
CLICK
1. Prepare Stroller
Set parking brake, rotate canopy
towards handlebar, place Restraint Belt
ends to the sides of stroller seat (see
stroller owner’s manual if necessary).
2. Align Infant Car Seat
Place Infant Car Seat “rear facing”
directly centered on top of ICSA, align
Groove Features on Infant Car Seat
with Front and Middle Tubes on ICSA.
3. Verify Infant Car Seat is Latched
Properly
Push Infant Car Seat straight down
onto ICSA until the adapters on each
side lock into the receivers on ICSA.
4. Verify Infant Car Seat is
Securely Attached
Pull up to ensure the Infant Car
Seat is secure.
5. Secure Restraint Belt
Proceed to section titled “Securing
Restraint Belt” (pg.14).
Failure to properly
secure Restraint Belt and
to properly install Infant
Car Seat on Infant Car
Seat Adapter may result
in accident, injury or
death.
CS1107 ICSA PEG PEREGO
PRIMO VIAGGIO SIP & SIP 30/30
14
P637400A
SECURING RESTRAINT BELT
1. Fasten Restraint Belt
Fasten restraint belt over Infant Car
Seat securely. For Infant Car Seat to
be installed properly, the restraint
belt must be used each time the
Infant Car Seat is used with the
stroller.
2. Adjust Restraint Belt
Pull on Red Ring to tension Restraint
Belt.
Failure to properly secure
Restraint Belt may result in
accident, injury or death. Be
sure Restraint Belt tension
is not constricting child as it
may cause serious injury or
death.
1. Prepare Stroller
Set parking brake, rotate canopy
towards handlebar (see stroller
owner’s manual if necessary).
2. Unfasten Restraint Belt
Unfasten buckle, place Restraint Belt
ends to the sides of stroller seat.
REMOVING INFANT CAR
SEAT FROM STROLLER
15
P637400A
FOLDING STROLLER
WITH ICSA ATTACHED
Care must be taken when
folding and unfolding the
stroller to prevent finger
entrapment or injury.
To avoid injuries, never fold
or unfold stroller with other
individuals within reach of
stroller.
1. Set Parking Brake
Set parking brake (see stroller
owner’s manual if necessary).
2. Unfasten Restraint Belt
Unfasten buckle, place Restraint Belt
ends to sides of stroller seat.
3. Remove Infant Car Seat
Remove Infant Car Seat from ICSA.
4. Empty Stroller
Remove contents from low boy cargo
basket and pockets.
5. Fold Handlebar
Squeeze both handlebar release
levers simultaneously (see stroller
owner’s manual if necessary).
6. Rotate Handlebar Forward
Slightly rotate handlebar towards
seat and hold in place during next
step.
7. Lift Red Frame Release Handle
Using a short, quick tug, lift red frame
release handle up. Keep tires on
ground as stroller collapses toward
front wheel (see stroller owner’s
manual if necessary).
Prepare Stroller
Set parking brake, rotate canopy
towards handlebar (see stroller
owner’s manual if necessary).
NOTE: We do not recommend
leaving stroller folded with ICSA
installed for long periods of time as
it may leave an imprint in the stroller
seat. For long term folded storage,
remove ICSA.
Remove Infant Car Seat
Adapter and Restraint Belt
when not in use.
Do not place children directly
in the stroller seat with the
Infant Car Seat Adapter
installed. Remove Infant Car
Seat Adapter from stroller
prior to placing a child
directly into the stroller seat.
Failure to follow these
warnings may result in
serious injury or death.
REMOVING ICSA
FROM STROLLER
16
P637400A
2. Slide Covers Up
Push to slide each Cover (at front of
stroller Accessory Adapters) up on
each side of stroller, covering each
Receiver Socket.
REMOVING RESTRAINT BELT
FROM STROLLER
Restraint Belt is intended
for use with combination of
BOB Infant Car Seat Adapter
and compatible Infant Car
Seats only. The Restraint Belt
must be removed prior to
using stroller without Infant
Car Seat. Failure to remove
Restraint Belt when not in
use may result in accident,
injury or death.
1. Unscrew Captured Screws
Using a screwdriver, unscrew each
Captured Screw from each respective
stroller Anchor Nut.
2. Keep Restraint Belt
Keep restraint belt together with
ICSA for next use.
1. While holding down Red Release
Buttons on both Accessory Adapters
at sides of stroller, pull ICSA forward
and out of Receiver Sockets, keeping
alignment even, left to right, as you
pull.
17
P637400A
LIMITED WARRANTY
We take pride in the workmanship
of BOB Gear by Britax and strive
to manufacture the best products
possible. Therefore, we warranty
our Infant Car Seat Adapters (ICSA)
against defects in material and
workmanship for the periods and
parts set forth below, subject to the
conditions listed below. Since no
product is indestructible, it does
not cover defects attributable to or
resulting from normal wear, abuse or
alteration.
FRAME AND COMPONENTS
The frame is warranted for five
years. Components and fabric are
warranted for one year. Warranty
is only valid for the original
purchaser. Proof of purchase is
required to exercise this warranty.
Labor and freight charges are not
included. Britax reserves the right to
discontinue or change fabrics, parts,
models or products, or to make
substitutions.
NORMAL WEAR
Normal wear, corrosion, neglect,
abuse, accidents, improper assembly
or maintenance, or the installation of
parts or accessories not compatible
with the original intended use of the
ICSA, as sold, are not covered by
this warranty. Tires and tubes are not
covered under the limited warranty.
WARRANTY CLAIMS
Warranty claims must be made
through an authorized dealer or BOB
Gear by Britax Customer Service.
This warranty is limited to the repair
or replacement of the defective
part. Britax shall in no event be
responsible for consequential or
special damages.
This limited warranty is the only
express or implied warranty
applicable to this BOB Gear
product and is warranted by Britax
Child Safety, Inc. Any implied
warranties, including warranties of
merchantability and fitness shall
be limited in scope and duration
in accordance with this limited
warranty.
BOB Gear by Britax
© 2014 Britax Child Safety, Inc.
(888) 427-4829
(704) 409-1699
www.bobgear.com
18
P637400A
MISE EN GARDE
Prenez soin de ne pas emprunter les circuits hors route ou
les terrains accidentés si vous utilisez l’adaptateur pour siège
auto avec le siège auto installé, sous peine de déstabiliser la
poussette et de la faire basculer, avec pour conséquence de
graves blessures.
• Veillez à toujours utiliser le harnais du siège auto, sans quoi le
bébé pourrait tomber ou glisser hors du siège, et se blesser
gravement.
• Prenez soin de ne pas modifier l’adaptateur pour siège auto ni
de retirer les étiquettes. Ce faisant, vous annuleriez la garantie
et risqueriez de mettre en péril la sécurité du bébé.
• Faites attention de ne pas vous coincer ou pincer les doigts
quand vous dépliez ou repliez la poussette.
• Respectez à la lettre les consignes du fabricant du siège auto.
Ne dépassez pas la capacité de charge maximale du siège
auto précisée dans les instructions du fabricant, sous peine
de déstabiliser la poussette et de la faire basculer, avec pour
conséquence de graves blessures.
• Veillez à ne pas courir ou faire votre jogging si vous utilisez
l’adaptateur pour siège auto avec le siège auto, sous peine
de déstabiliser la poussette et de la faire basculer, avec pour
conséquence de graves blessures.
LE NON-RESPECT DE CES MISES EN GARDE ET DES
CONSIGNES DE MONTAGE PEUT ENTRAÎNER DE
GRAVES BLESSURES, VOIRE LA MORT.
19
P637400A
Conservez les instructions en lieu sûr à des fins d'utilisation et de
référence ultérieures.
Pour un fonctionnement en toute sécurité, lisez attentivement
l'intégralité des consignes et des mises en garde avant usage.
L'adaptateur pour siège auto pour bébé BOB
®
est conçu pour
une utilisation avec les poussettes BOB équipées d'adaptateurs
d'accessoire et les sièges auto compatibles. Ce produit n'est pas un
adaptateur universel. Ne l'utilisez pas avec des modèles de sièges
auto autres que ceux répertoriés dans le tableau de compatibilité en
page21.
Ne laissez jamais les enfants sans surveillance dans la poussette et/ou
le siège auto.
Dans la poussette, maintenez toujours la poignée de transport du
siège auto verrouillée en position verticale/de transport, en guise de
protection supplémentaire pour votre enfant.
Vérifiez toujours que l'adaptateur pour siège auto est parfaitement
verrouillé dans les adaptateurs d'accessoire de la poussette avant
usage.
Fixez toujours le siège auto à l'adaptateur pour siège auto au moyen
de la courroie de maintien fournie.
Retirez l'adaptateur pour siège auto et la courroie de maintien quand
vous ne vous servez pas du siège auto.
Ne mettez pas votre enfant directement dans la poussette quand
l'adaptateur pour siège auto est installé. Retirez d'abord l'adaptateur
pour siège auto de la poussette avant d'y mettre votre enfant.
La courroie de maintien est conçue uniquement pour une utilisation
en conjonction avec l'adaptateur pour siège auto BOB et des sièges
auto compatibles. Retirez la courroie de maintien avant d'utiliser la
poussette sans le siège auto.
Quand vous fixez le siège auto à l'adaptateur pour siège auto, veillez
à tenir vos mains et vos doigts à l'écart des surfaces de contact.
FÉLICITATIONS
REMARQUES IMPORTANTES
Félicitations pour votre achat de l'adaptateur pour siège auto pour bébé BOB.
Il a été conçu pour fixer un siège auto à une poussette BOB.
Consultez le tableau en page21 pour des détails sur les modèles d'adaptateurs
et de sièges auto pour bébé compatibles. Recherchez les caractéristiques
principales de votre adaptateur pour siège auto sur les pages Structure, et
suivez les consignes s'y rapportant.
Pour des versions actualisées du présent manuel, la garantie et autres
notifications récentes de produits, rendez-vous sur www.bobgear.com
régulièrement, ou avant d'apporter des modifications approuvées ou d'ajouter
du matériel autorisé à votre poussette.
20
P637400A
TABLE DES MATIÈRES
Mises en garde .............................................................................................. 18
Remarques importantes ................................................................................ 19
Table des matières ........................................................................................ 20
Tableau de compatibilité .............................................................................. 21
Structure de l’adaptateur S924600 pour siège auto Peg Perego Primo 4.35
......... 22
Structure de l’adaptateur CS1107 pour siège auto Peg Perego Primo Viaggio SIP
....... 22
Structure du siège auto Peg Perego Primo Viaggio 4.35 ............................ 23
Structure du siège auto Peg Perego Primo Viaggio SIP .............................. 23
Structure de l’adaptateur d’accessoire de poussette ................................. 24
Structure de la courroie de maintien ............................................................ 24
Structure de l’ancrage de la capote ............................................................. 24
Installation de votre adaptateur ................................................................... 25
Fixation de la courroie de maintien ......................................................................25
Installation de l’ancrage de la capote ...................................................................26
Fixation de l’adaptateur à la poussette ........................................................ 26
Préparation de la poussette en vue de l’installation de l’adaptateur ...............26
Installation de l’adaptateur .....................................................................................27
Préparation en vue de la fixation du siège auto .......................................... 27
Installation du siège auto .............................................................................. 28
Adaptateur S924600 pour sièges Peg Perego Primo Viaggio 4.35, SIP et SIP 30/30
...28
Adaptateur CS1107 pour sièges Peg Perego Primo Viaggio SIP et SIP 30/30
............29
Fixation de la courroie de maintien .............................................................. 30
Retrait du siège auto de la poussette ........................................................ 30
Pliage de la poussette avec l’adaptateur fixé .............................................. 31
Retrait de l’adaptateur de la poussette ....................................................... 31
Retrait de la courroie de maintien de la poussette ...................................... 32
Garantie limitée ............................................................................................ 33
BOB
®
, BOB Gear
®
, BRITAX
®
et DUALLIE
®
sont des marques de commerce, déposées
aux États-Unis d’Amérique et dans d’autres pays, qui appartiennent à Britax. Tous
droits réservés.
Ce produit et ses composants peuvent faire l’objet de modifications sans préavis.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50

BOB Duallie Manuel utilisateur

Catégorie
Poussettes
Taper
Manuel utilisateur

dans d''autres langues