Danby DPA100HE5BDB6 Le manuel du propriétaire

Marque: Danby

Modèle: DPA100HE5BDB6

Taper: Le manuel du propriétaire

Ce manuel convient également à

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

MODEL • MODÈLE • MODELO

DPA100E5WDB-6

DPA100HE5BDB-6

2020.11.24

PORTABLE AIR CONDITIONER

Owner’s Manual.............................1 - 19

CLIMATISEUR PORTABLE

Manuel du propriétaire.................20 - 38

AIRE ACONDICIONADO PORTÁTIL

Manual del propietario.................39 - 57

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

SAFETY REQUIREMENTS

DANGER: Risk of ﬁ re or explosion. Flammable

refrigerant used. Do not damage the refrigerant

circuit.

• Ensure that servicing is done by factory

authorized service personnel, to minimize

product damage or safety issues.

• Consult repair manual or owner’s guide before

attempting to service this product. All safety

precautions must be followed.

• Dispose of properly in accordance with federal

or local regulations.

• Follow handling instructions carefully.

• Keep ventilation openings, in the appliance clear

of obstruction.

• Do not use mechanical devices or other means

to accelerate the defrosting process.

• Children should be supervised to ensure that

they do not play with the appliance.

• Do not store or install the appliance near

continuously operating ignition sources such as

open ﬂ ames or a gas stove.

• Do not operate near water or in a wet room.

• Do not pierce or burn.

• Be aware that refrigerants may not contain an

odor.

• The appliance must be stored so as to prevent

mechanical damage from occurring.

All wiring must comply with local and national

codes and must be installed by a qualiﬁ ed

electrician. Check the available power supply and

resolve any wiring problems before installing and

operating this appliance.

The rating plate located on the right side of the

appliance just above the power cord contains

electrical and other technical data.

This appliance is not intended for use by persons

(including children) whose physical, sensory or

mental capabilities may be different or reduced,

or who lack experience or knowledge, unless such

persons receive supervision or training to operate

the appliance by a person responsible for their

safety.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding

reduces the risk of electrical shock by providing an

escape wire for the electrical current.

This appliance has a cord that has a grounding

wire with a 3-prong plug. The power cord must be

plugged into an outlet that is properly grounded.

If the outlet is a 2-prong wall outlet, it must be

replaced with a properly grounded 3-prong wall

outlet. The serial rating plate indicates the voltage

and frequency the appliance is designed for.

WARNING - Improper use of the grounding

plug can result in a risk of electric shock.

Consult a qualiﬁ ed electrician or service agent

if the grounding instructions are not completely

understood, or if doubt exists as to whether the

appliance is properly grounded.

Do not connect your appliance to extension

cords or together with another appliance in the

same wall outlet. Do not splice the power cord.

Do not under any circumstances cut or remove the

third ground prong from the power cord. Do not

use extension cords or ungrounded (two prongs)

adapters.

If the power supply cord is damaged, it must be

replaced by the manufacturer, its service agent or

similar qualiﬁ ed person in order to avoid hazard.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Any person involved with working on the refrigerant

circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which

authorizes their competence to handle refrigerants

safely in accordance with an industry recognized

assessment speciﬁ cation.

Servicing shall only be performed as recommended

by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel

shall be carried out under the supervision of

the person competent in the use of ﬂ ammable

refrigerants.

When maintaining or disposing of the appliance the

refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

Information on servicing

1. Checks to the area: Prior to beginning work

on systems containing ﬂ ammable refrigerants,

safety checks are necessary to ensure that the

risk of ignition is minimized. For repair to the

refrigerating system, the following precautions

shall be complied with prior to conducting work

on the system.

2. Work procedure: Work shall be undertaken

under a controlled procedure so as to minimize

the risk of a ﬂ ammable gas or vapour being

present while the work is being performed.

3. General work area: All maintenance staff

and others working in the local area shall

be instructed on the nature of work being

carried out. Work in conﬁ ned spaces shall be

avoided. The area around the work space shall

be sectioned off. Ensure that the conditions

within the work area have been made safe by

removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The

area shall be checked with an appropriate

refrigerant detector prior to and during work

to ensure the technician is aware of potentially

ﬂ ammable atmospheres. Ensure that the leak

detection equipment being used is suitable

for use with ﬂ ammable refrigerants, i.e. non-

sparking, adequately sealed and intrinsically

safe.

5. Presence of ﬁ re extinguisher: If any hot work is

to be conducted on the refrigeration equipment

or any associated parts, appropriate ﬁ re

extinguishing equipment shall be available

to hand. Have a dry powder or C0

ﬁ re

extinguisher adjacent to the work area.

6. No ignition sources: No person carrying out

work in relation to a refrigeration system which

involves exposing any pipe work that contains

or has contained ﬂ ammable refrigerant shall use

any sources of ignition in such a manner that it

may lead to risk of ﬁ re or explosion. All possible

ignition sources including cigarette smoking,

should be kept sufﬁ ciently far away from the

site of installation, repairing, removing and

disposal during which ﬂ ammable refrigerant can

possibly be released to the surrounding space.

Prior to work taking place, the area around the

equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No

smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the

open or that it is adequately ventilated before

breaking into the system or conducting any hot

work. A degree of ventilation shall continue

during the period that the work is carried out.

The ventilation should safely disperse any

released refrigerant and preferable expel it

externally into the atmosphere.

8. Checks to the refrigeration equipment: Where

electrical components are being changed, they

shall be ﬁ t for the purpose and to the correct

speciﬁ cation. At all times the manufacturer’s

maintenance and service guidelines shall be

followed. If in doubt consult the manufacturer’s

technical department for assistance.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

The following checks shall be applied to installations

using ﬂ ammable refrigerants:

• The charge size is in accordance with the room

size within which the refrigerant containing

parts are installed.

• The ventilation machinery and outlets are

operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used,

the secondary circuit shall be checked for the

presence of refrigerant.

• Marking to the equipment continues to be visible

and legible. Markings and signs that become

illegible must be corrected.

• Refrigeration pipe or components are installed in

a position where they are unlikely to be exposed

to any substance which may corrode refrigerant

containing components, unless the components

are constructed of materials which are inherently

resistant to being corroded or are suitable

protected against being corroded.

9. Checks to electrical devices: Repair and

maintenance to electrical components shall

include initial safety checks and component

inspection procedures. If a fault exists that

could compromise safety, then no electrical

supply shall be connected to the circuit until it

is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to

continue operation, an adequate temporary

solution shall be used. This shall be reported to

the owner of the equipment so all parties are

advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be

done in a safe manner to avoid possibility of

sparking.

• That no live electrical components and wiring

are exposed while charging, recovering or

purging the system.

• That there is continuity of earth bonding.

Repairs to sealed components

1. During repairs to sealed components, all

electrical supplies shall be disconnected from

the equipment being worked upon prior to any

removal of sealed covers, etc. If it is absolutely

necessary to have an electrical supply to

equipment during servicing then a permanently

operating form of leak detection shall be located

at the most critical point to warn of a potentially

hazardous situation.

2. To ensure that by working on electrical

components the casing is not altered in such

a way that the level of protection is affected,

particular attention shall be paid to the

following:

• Damage to cables, excessive number of

connections, terminals not made to original

speciﬁ cation, damage to seals, incorrect ﬁ tting

of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have

not degraded such that they no longer serve

the purpose of preventing the ingress of

ﬂ ammable atmospheres. Replacement parts

shall be in accordance with the manufacturer’s

speciﬁ cations.

Note: The use of silicon sealant may inhibit the

effectiveness of some types of leak detection

equipment. Intrinsically safe components do not

have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or

capacitance loads to the circuit without ensuring

that this will not exceed the permissible voltage

and current permitted for the equipment in use.

Intrinsically safe components are the only types that

can be worked on while live in the presence of a

ﬂ ammable atmosphere. The test apparatus shall

be at the correct rating. Replace components only

with parts speciﬁ ed by the manufacturer. Other

parts may result in the ignition of refrigerant in the

atmosphere from a leak.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Removal and evacuation

When breaking into the refrigerant circuit to make

repairs or for any other purpose conventional

procedures shall be used. However, it is important

that the best practice is followed since ﬂ ammability

is a consideration. The following procedures shall

be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into

the correct recovery cylinders. The system shall

be ﬂ ushed with OFN to render the unit safe. This

process may need to be repeated several times.

Compressed air or oxygen shall not be used for

this task.

• Flushing shall be achieved by breaking the

vacuum in the system with OFN and continuing

to ﬁ ll until the working pressure is achieved, then

venting to atmosphere and ﬁ nally pulling down

to a vacuum. This process shall be repeated until

no refrigerant is within the system. When the

ﬁ nal OFN charge is used, the system shall be

vented down to atmospheric pressure to enable

work to take place. This operation is absolutely

vital is brazing operations on the pipe-work are

to take place.

• Ensure that the outlet for the vacuum pump is

not close to any ignition sources and there is

ventilation available.

Charging procedures

In addition to conventional charging procedures, the

following requirements shall be followed:

• Ensure that contamination of different

refrigerants does not occur when using charging

equipment. Hoses or lines shall be as short as

possible to minimize the amount of refrigerant

contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed

prior to charging the system with refrigerant.

• Label the system when charging is complete, if

not already labeled.

• Extreme care shall be taken not to overﬁ ll the

refrigeration system.

• Prior to recharging the system it shall be

pressure tested with OFN. The system shall be

leak tested on completion of charging but prior

to commissioning. A follow up leak test shall be

carried out prior to leaving the site.

Cabling

Check that cabling will not be subject to wear,

corrosion, excessive pressure, vibration, sharp

edges or any other adverse environmental effects.

The check shall also take into account the effects of

aging or continual vibration from sources such as

compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of

ignition be used in the searching for or detection

of refrigerant leaks. A halide torch or any other

detector using a naked ﬂ ame shall not be used.

Leak detection methods

The following leak detection methods are deemed

acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect

ﬂ ammable refrigerants but the sensitivity may

not be adequate or may need recalibration.

Detection equipment shall be calibrated in a

refrigerant-free area. Ensure that the detector is

not a potential source of ignition and is suitable

for the refrigerant used.

• Leak detection equipment shall be set at a

percentage of the LFL of the refrigerant and

shall be calibrated to the refrigerant employed

and the appropriate percentage of gas (25%

maximum) is conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with

most refrigerants but the use of detergents

containing chlorine shall be avoided as the

chlorine may react with the refrigerant and

corrode the copper or pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be

removed or extinguished.

• If a leakage of refrigerant is found which

requires brazing, all of the refrigerant shall be

recovered from the system or isolated by means

of shut off valves in a part of the system remote

from the leak. Oxygen free nitrogen (OFN) shall

then be purged through the system both before

and during the brazing process.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Decommissioning

Before carrying out this procedure, it is essential

that the technician is completely familiar with the

equipment in all its detail. It is recommended good

practice that all refrigerants are recovered safely.

Prior to the task being carried out, an oil and

refrigerant sample shall be taken in case analysis is

required prior to re-use of reclaimed refrigerant. It

is essential that electrical power is available before

the task is commenced.

A. Become familiar with the equipment and its

operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available

if required for handling refrigerant cylinders.

• All personal protective equipment is

available and being used correctly.

• The recovery process is supervised at all

times by a competent person.

• Recovery equipment and cylinders conform

to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so

that refrigerant can be removed from various

parts of the system.

F. Make sure that cylinder is situated on the scales

before recovery takes place.

G. Start the recovery machine and operate in

accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80%

volume liquid charge.

I. Do not exceed the maximum working pressure

of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly

and the process is completed, make sure that the

cylinders and the equipment are removed from

the site promptly and all isolation valves on the

equipment are closed off.

K. Recovered refrigerant shall not be charged into

another refrigeration system unless it has been

cleaned and checked.

Labeling

Equipment shall be labeled stating that it has been

decommissioned and emptied of refrigerant. The

label shall be dated and signed. Ensure that there

are labels on the equipment stating the equipment

contains ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for

servicing or decommissioning, it is recommended

good practice that all refrigerants are removed

safely.

When transferring refrigerant into cylinders, ensure

that only appropriate refrigerant recovers cylinders

are employed. Ensure that the correct number of

cylinders for holding the total system charge are

available. All cylinders to be used are designed

for the recovered refrigerant and labeled for that

refrigerant, i.e. special cylinders for the recovery

of refrigerant. Cylinders shall be complete with

pressure relief valve and associated shut-off valves

in good working order. Empty recovery cylinders

are evacuated and, if possible, cooled before

recovery occurs.

The recovery equipment shall be in good working

order with a set of instructions concerning the

equipment that is at hand and shall be suitable for

the recovery of ﬂ ammable refrigerants. In addition,

a set of calibrated weighing scales shall be

available and in good working order. Hoses shall

be complete with leak-free disconnect couplings

and in good condition. Before using the recovery

machine, check that is it in satisfactory working

order, has been properly maintained and that any

associated electrical components are sealed to

prevent ignition in the event of a refrigerant leak.

Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the

refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be

arranged. Do not mix refrigerants in recovery units

and especially not in cylinders. If compressors or

compressor oils are to be removed, ensure that they

have been evacuated to an acceptable level to make

certain that ﬂ ammable refrigerant does not remain

within the lubricant. The evacuation process shall be

carried out prior to returning the compressor to the

suppliers. Only electric heating to the compressor

body shall be employed to accelerate this process.

When oil is drained form a system, it shall be

carried out safely.

INSTALLATION INSTRUCTIONS

ACCESSORIES

1. Air outlet adapter

2. Exhaust hose

3. Window slider adapter

4. 8 bolts

5. Window slider A and B

6. Window slider C and D

7. Foam seal A and B (adhesive)

8. Foam seal C (non-adhesive)

9. Drain hose

10. Remote control and batteries

REQUIRED TOOLS

1. Medium sized Phillips screwdriver

2. Tape measure or ruler

3. Knife or scissors

4. Saw (in the event that the window sliders need to

be cut to size)

ASSEMBLING THE WINDOW KIT

1. Attach the air outlet adapter and the window

slider adapter onto either end of the exhaust

hose.

2. Insert the air outlet adapter into the back of the

appliance by placing over the air exhaust and

then pushing in the direction of the arrow to lock

into place.

3. Measure the window opening where the window

kit will be installed. Assemble as many sliders as

necessary to ﬁ t the window. If the length of the

window requires all three sliders, use two bolts

to fasten the sliders at the correct length. If the

window opening is less that the minimum length

of a single slider, use the slider that has the hole

in it and cut it to the correct length. Make sure

not to cut the end that has the hole as this is

necessary to attach the exhaust hose adapter.

Important: The drain hose is only included on

models that include heat mode.

INSTALLATION INSTRUCTIONS

IMPORTANT WARNING

Do not leave this appliance unattended

in a space where people or animals who

cannot react to a malfunction are located. A

malfunction such as the exhaust hose becoming

dislocated, can cause extreme overheating or

death in an enclosed, unattended space.

INSTALLING THE WINDOW KIT

The window kit can be used in either a hung

window or a sliding window application. The

images at the right are for a hung window. The

steps for a sliding window are the same.

1. Cut the adhesive foam seals A and B to the

correct length for the window. Attach them to the

window sash and frame as shown.

2. Insert the assembled window slider kit into the

window opening.

3. Cut the non-adhesive foal seal C to match

the width of the window. Insert the foam seal

between the glass and the window frame to

prevent air and insects from getting into the

room.

4. Attach the window slider adapter to the hole in

the window slider kit.

Note: It may be easier to attach the window slider

adapter to the window slider kit before placing the

kit in the window.

Note: Do not over extend or bend the hose as this

will impede air ﬂ ow.

OPERATING INSTRUCTIONS

FEATURES

1. Control panel

2. Louver

3. Remote control receiver

4. Handle (both sides)

5. Casters

6. Air intake grille

7. Air outlet grille

8. Continuous drain

9. Air intake grille

10. Power cord

11. Condenser drain

LOCATION

Place the air conditioner on a smooth, level ﬂ oor

that is strong enough to support it and all included

accessories.

Make sure the appliance is level to minimize noise

and vibration.

The appliance must be installed near a grounded

receptacle and the overﬂ ow drain outlet on the rear

of the appliance must be accessible.

Do not cover air inlets or outlets or the remote

control receiver on the control panel.

The appliance requires 45 cm (17.7 inches) of

clearance on the front and sides.

The appliance requires at least 50 cm (20 inches) of

clearance on the back.

OPERATING INSTRUCTIONS

CONTROL PANEL

1. Timer button: Used to set the automatic timer.

2. Fan button: Used to choose the fan speed.

3. Temperature control buttons: Used to increase or

decrease the set temperature.

4. Mode button: Used to choose the mode; cool,

fan or dry.

5. Power button: Used to turn the appliance on or

off.

Note: Images are for instructional purposes only.

Your control panel may look slightly different.

OPERATING MODES

Dry Mode

• Press the mode button to choose dry mode.

• The fan speed will be set to auto.

• The exhaust hose should be installed during dry

mode to ensure the best results.

• It may be necessary to install the continuous

drain hose during dry mode to remove excess

water.

Heat Mode

• Press the mode button to choose heat mode.

• Use the temperature control buttons to choose

the desired temperature.

• Press the fan button to choose the desired fan

speed.

• The temperature can be set within a range of 13

- 27°C (55 - 81°F).

• The exhaust hose should be installed during heat

mode to ensure the best results.

• It may be necessary to install the continuous

drain hose during heat mode to remove excess

water.

• Heat mode is not available on all models.

Smart Mode

• Press the mode button the choose smart mode.

• The appliance will choose whether to run cool,

fan or heat mode automatically based on the

ambient temperature in the air.

• Smart mode is not available on all models.

OPERATING MODES

Cool Mode

• Press the mode button to choose cool mode.

• Use the temperature control buttons to choose

the desired temperature.

• Use the fan button to choose the desired fan

speed.

• The temperature can be set within a range of 18

- 32°C (64 - 90°F).

• The exhaust hose should be installed during cool

mode to ensure the best results.

Fan Mode

• Press the mode button to choose fan mode.

• Press the fan button to choose the desired fan

speed.

• The exhaust hose does not need to be installed

during fan mode.

OPERATING INSTRUCTIONS

TIMER FUNCTION

The timer function can be used to turn the appliance

on or off after a period of time to conserve energy.

To set the timer to turn the appliance off:

1. While the appliance is running, press the timer

button. The time display will ﬂ ash.

2. Press the timer button to choose the number of

hours before the appliance will turn off.

3. Wait 5 seconds to conﬁ rm the setting. The timer

icon will illuminate.

To set the timer to turn the appliance on:

1. Turn the appliance on and choose the desired

mode and settings. Turn the appliance off.

2. While the appliance is turned off, press the timer

button. The time display will ﬂ ash.

3. Press the timer button to choose the number of

hours before the appliance will turn on.

4. Wait 5 seconds to conﬁ rm the setting. The timer

icon will illuminate.

Notes: Turning the appliance on or off at any time

or adjusting the timer setting to 0 hours will cancel

the timer settings.

CHILD LOCK

The child lock can be activated by pressing the

temperature control buttons on the remote control

at the same time for 3 seconds. The buttons on the

remote control cannot be used while the child lock is

active. To deactivate the child lock, press and hold

the temperature control buttons at the same time for

3 seconds.

The child lock can only be activated or deactivated

using the remote control.

TURBO

The turbo setting will run the air conditioner at

maximum settings to cool the room as quickly

as possible. Press the turbo button and the turbo

symbol will ﬂ ash 10 times on the display. The fan

speed and temperature cannot be adjusted.

FOLLOW ME

The follow me feature can only be activated from

the remote control.

The remote control has a thermostat inside of

it. Keep the remote control will you and the

air conditioner will automatically adjust the set

temperature based on the ambient temperature at

your location.

The maximum distance for the follow me feature is

8 meters (26 feet). This feature is available in cool

and auto modes.

To activate follow me, press the turbo button and

then press the temperature control buttons until the

follow me icon appears on the display and then

press the turbo button to conﬁ rm the selection.

The remote control display will show the actual

ambient temperature at its location. The remote

control will sent a signal to the air conditioner every

20 minutes to update the set temperature. If the

air conditioner does not receive a signal from the

remote control during any 25 minute period, the

follow me feature will deactivate.

To deactivate follow me, press the turbo button and

then press the temperature control buttons until the

follow me icon ﬂ ashes on the display and then press

the turbo button to conﬁ rm the selection.

SLEEP

The sleep feature can be used to conserve energy

during sleeping hours. This feature can be used

during cool and heat mode.

When selected in cool mode, the set temperature

will increase by 1 degree per hour for 2 hours. The

appliance will hold the new set temperature for

6 hours before automatically returning to normal

operation.

When selected in heat mode, the set temperature

will decrease by 1 degree per hour for 3 hours.

The appliance will hold the new set temperature for

5 hours before automatically returning to normal

operation.

The sleep feature can only be activated with the

remote control and can be canceled at any time by

pressing the sleep button.

OPERATING INSTRUCTIONS

REMOTE CONTROL

1. Power button: Used to turn the appliance on or off.

2. Turbo button: The turbo function can be used to cool a room

quickly.

3. Temperature control buttons: Used to increase or decrease

the set temperature.

4. Timer button: Used to set the timer function.

5. Mode button: Used to choose the mode.

6. Swing button: The swing feature is not available on this

model.

7. Sleep button: Used to set the sleep function.

8. Fan button: Used to set the fan speed.

9. °C/°F button: Used to change the temperature scale between

Celsius and Fahrenheit.

Note: The remote control will function within a range of 7 meters

(23 feet) of the appliance.

REMOTE DISPLAY

The digital display on the remote control will show the below

symbols. Please note that not all features may be available on

your model. If you try to use a feature that your model does not

support, the appliance will default to fan mode.

1 2

OPERATING INSTRUCTIONS

IMPORTANT

Do not dispose of batteries as unsorted municipal

waste. Refer to local laws for proper disposal of

batteries.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation.

If this equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference

by one or more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment

and receiver

3. Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected

4. Consult the dealer or an experienced radio/TV

technician for help

Changes or modiﬁ cations not approved by the

party responsible for FCC compliance could void

the user’s authority to operate the equipment. This

appliance complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference

received, including interference that may cause

undesired operation.

This device complies with Canadian CAN ICES-3

(B) / NMB-3 (B)

REPLACING THE REMOTE BATTERIES

This air conditioner comes with two AAA batteries.

Place the batteries in the remote control before use.

1. Slide the back cover from the remote downward

to expose the battery compartment.

2. Insert the batteries, ensure to match the (+) and

(-) symbols on the ends of the batteries with the

symbols inside the battery compartment.

3. Slide the battery cover back into place.

Notes:

• The air conditioner will not respond if curtains,

doors or other materials block the signal from

the remote control to the unit.

• Prevent any liquid from contact with the remote

control. Do not expose the remote control to

direct sunlight or heat.

• If the infrared signal receiver on the indoor unit

is exposed to direct sunlight, the air conditioner

may not function properly. Use curtains to

prevent the sunlight from falling on the receiver.

• Do not mix old and new batteries or batteries of

different types.

• Do not leave the batteries in the remote control

if it is not going to be used for more than 2

months.

OPERATING INSTRUCTIONS

2. Continuous Drain

During the dry mode, you may wish to set up the

continuous drain option so that the appliance will

automatically drain collected water. Ensure that the

appliance is turned off and unplugged from the

power source before setting up the drain hose.

Remove the drain plug and attach the drain hose

that was provided with the appliance. Ensure that

there are no kinks or bends in the drain hose as this

can stop water from draining.

Place the open end of the drain hose over the

receptacle that the appliance will drain into; this

could be a basement ﬂ oor drain, a sink or similar.

Remember that there is no drain pump in this

appliance, the continuous drain is activated by

gravity only. Ensure that the drain hose goes straight

down toward the ﬂ oor from the drain connection.

If the hose is not positioned directly downwards,

water will not drain correctly.

WATER DRAINAGE

When the internal drain pan becomes full the

appliance will stop operating and the display

will show error code “Ft”. The air conditioning or

dehumidifying action will stop but the fan may

continue to operate.

There are two methods to drain water from the

appliance:

1. Drain Plug

1. Turn the appliance off and unplug it from the

power source.

2. Carefully move the appliance to a location

where the water can be drained.

3. Remove the drain plug and allow the water to

completely drain.

4. Replace the bottom drain plug, pressing ﬁ rmly to

ensure a tight ﬁ t and no leaks.

5. The “Ft” error symbol will disappear and the

appliance will resume regular function once

power is restored.

This appliance also includes a secondary drain

in the middle of the back panel. If the hose is not

draining when attached to the lower drain, move

the hose to the middle drain using the same steps

outlined above. The middle drain being higher off

the ground, can provide better draining based on

the pull of gravity.



CLEANING

• Unplug the appliance before cleaning or

servicing.

• Clean the cabinet with a lukewarm damp cloth

and neutral detergent. Dry the cabinet with a

lint-free dry cloth.

• Do not use gasoline, paint thinner or other

chemicals to clean the appliance.

• Do not wash the appliance directly under a tap

or using a hose. It may cause electrical damage.

AIR FILTER

The ﬁ lters in this appliance should be cleaned every

two weeks to ensure efﬁ cient performance.

In households with animals, the air ﬁ lters may need

to be cleaned more often and the external grills may

need to be wiped to prevent blocked air ﬂ ow.

LONG-TERM STORAGE

1. Drain all water from the appliance.

2. Run the appliance on fan mode for half a day in

a warm room to dry the inside of the appliance

and prevent mold formation.

3. Turn off the appliance and unplug it, wrap the

cord and bundle it with tape.

4. Remove the battery from the remote control.

5. Clean the air ﬁ lters and reinstall them.

6. Store the appliance in a cool, dark place.

Prolonged exposure to direct sunlight or extreme

heat can shorten the lifespan of the appliance.

DISPOSAL

This appliance should not be treated as regular

household waste. Check for local regulatory

compliance regarding the approved and safe

disposal of this appliance.

Do not dispose of batteries as unsorted municipal

waste. Refer to local laws for proper disposal of

batteries.

ERROR CODES

Lt - low temperature - the appliance will pause

functioning if ice forms on the internal structure;

the appliance will resume normal functioning

automatically when the ice melts

PF - sensor failure - unplug the appliance for 5

minutes to reset the internal sensors; if the error

code persists after plugging the appliance back

in, please contact consumer care for servicing

information

Ft - water tray is full - attach drain hose and drain

excess water

CARE & MAINTENANCE

FREQUENTLY ASKED QUESTIONS

Can I leave my AC in place through the winter?

This is not recommended.

What are the standard wattage and amps used?

Information pertaining to watts and amps can be found on the rating plate located on the side of the unit.

When should I use the exhaust hose?

The exhaust hose should be used in cool, dry, heat and auto modes. It is not required in fan mode.

Can I use an extension cord?

No, an extension cord may not be used.

Can I extend the length of the exhaust hose?

No. The unit was designed with the length of the hose in mind and has only been tested under those

conditions. Instead use an additional fan to blow the cool air to other locations.

When should I use the drain hose?

The drain hose should be used in heat mode, dry mode or if using the continuous drain.

Where do I drain water from?

The water drains from the drainage port. If you are not using the continuous drain, the internal pan drains

from the bottom outlet.

Odors

Odour is caused by the formation of mold or mildew on internal surfaces. This can happen when there is

poor air circulation, a dirty ﬁ lter or the air conditioner was not used for a period of time.

• Ensure the ﬁ lter is clean.

• Run the unit on fan mode to remove any internal moisture.

• Check for any blockages in the drain lines and ensure there are no obstructions.

Please give your unit a hard reboot. Unplug it and plug it back in after 15-20 minutes. This allows the unit

to warm and drain if there is any frost stopping draining and go back to factory settings

For odour in a unit, we suggest using an algaecide tablet. You ﬁ rst need to turn the unit off, remove the

lower grill and ﬁ lter from the grill at the base of the unit, and then place the tablet in base.

TROUBLESHOOTING

Appliance will not operate

• Plug is not fully inserted into the wall outlet

• Blown fuse or circuit breaker

Insufﬁ cient cooling

• Air ﬁ lter is dirty

• Blocked air ﬂ ow

• Appliance size is too small for application

Noise

• The ground is not level

• The air ﬁ lter is dirty or blocked

• Gurgling sounds are normal, this is coolant moving inside the appliance

Odors

• Formation of mold or mildew on internal wet surfaces

• Place an algaecide tablet in the base pan; ensure the appliance is unplugged, remove the upper grille

and ﬁ lter, place the tablet in the middle water tray and replace the grille and ﬁ lter

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an authorized service

depot. Any appliance requiring service outside the limited boundaries of “In Home Service”, will be the consumer’s

responsibility to transport at their own expense to the original point of purchase or a service depot for repair. If the

appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center, it must

be delivered to the nearest authorized Danby Service Depot by the purchaser.

Transportation charges to and from the service location are not protected by this warranty and are the

responsibility of the purchaser.

During the ﬁrst twenty four (24) months, any functional parts of this product found to be defective, will be repaired

or replaced, at warrantor’s option, at no charge to the original purchaser.

Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where

service must be performed by a qualiﬁed service technician. If service is performed on the unit by anyone other

than an authorized service depot, all obligations of Danby under this warranty shall be void.

First 24 months

To obtain service

Boundaries of

in-home service

LIMITED “IN HOME” WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used

under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby

Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made

or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any

warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly

excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,

howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the

purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by

the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (ie. extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, ﬂoods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor

application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present

the proof of purchase to our authorized service depot.

Warranty Service

In Home

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

04/17

La page charge ...

Danby DPA100HE5BDB6 Le manuel du propriétaire

Marque: Danby

Modèle: DPA100HE5BDB6

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DPA100HE5BDB6 Owner's manual
español: Danby DPA100HE5BDB6 El manual del propietario

Danby DPA100HE5BDB6 Le manuel du propriétaire

Ce manuel convient également à

Danby DPA100HE5BDB6 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents