Wacker Neuson BS50-4HO EU Manuel utilisateur

5000184260 02 0211

Operator’s Manual

Rammer

BS 50-4s

5000184260

Notice d’Emploi

Pilonneuse

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000184236 02 0211

Foreword

wc_tx001537gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

Machine Item Number Rev

BS 50-4s 5000620071 209 and above

5000620811 208 and above

5000620322 100 and above

5000620818 100 and above

Foreword

4 wc_tx001537gb.fm

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

wc_bo5000184236_02TOC.fm 5

Table of ContentsBS 50-4s

Foreword 3

1 Emission Control Systems Information and Warranty 7

1.1 Emission Control System Background Information .............................. 7

1.2 Limited Defect Warranty for Wacker Neuson Emission Control

Systems ................................................................................................ 9

2 Safety Information 13

2.1 Signal Words Used in this Manual ..................................................... 13

2.2 Machine Description and Intended Use ............................................. 14

2.3 Safety Guidelines for Operating the Machine ..................................... 15

2.4 Operator Safety while Using Internal Combustion Engines ............... 17

2.5 Service Safety .................................................................................... 18

3 Labels 20

3.1 Label Locations .................................................................................. 20

3.2 Label Meanings .................................................................................. 21

4 Lifting and Transporting 25

4.1 Lifting and Transporting ...................................................................... 25

5 Operation 27

5.1 Preparing the Machine for First Use ................................................... 27

5.2 Recommended Fuel ........................................................................... 28

5.3 Position of the Operator ..................................................................... 29

5.4 Before Starting ................................................................................... 30

5.5 Starting ............................................................................................... 30

5.6 Stopping ............................................................................................. 31

5.7 Emergency Shutdown Procedure ....................................................... 31

5.8 Low Oil Shutoff Switch ....................................................................... 32

6 wc_bo5000184236_02TOC.fm

Table of Contents BS 50-4s

6 Maintenance 34

6.1 Maintaining the Emission Control System ...........................................34

6.2 Periodic Maintenance Schedule ..........................................................35

6.3 Servicing the Air Cleaner .....................................................................36

6.4 Engine Oil ............................................................................................37

6.5 Checking and Changing the Ramming System Oil .............................38

6.6 Shoe Hardware ...................................................................................40

6.7 Long-Term Storage .............................................................................41

7 Basic Troubleshooting 43

8 Technical Data 45

8.1 Rammer ...............................................................................................45

8.2 Sound Measurements .........................................................................46

8.3 Vibration Measurements .....................................................................46

8.4 Dimensions ..........................................................................................46

Emission Control Systems Information and Warranty

wc_tx001752gb.fm 7

1 Emission Control Systems Information and Warranty

The Emission Control Warranty and associated information is valid only for the

U.S.A., its territories, and Canada.

1.1 Emission Control System Background Information

Introduction

Wacker Neuson spark-ignited engines/equipment must conform with applicable

Environmental Protection Agency (EPA) and the State of California emissions

regulations. There are two types of emissions that fall under these regulations: 1)

exhaust, and 2) evaporative. These regulations require that manufacturers warrant

the emission control systems for defects in materials and workmanship.

Furthermore, EPA and California regulations require all manufacturers to furnish

written instructions describing how to operate and maintain the engines/equipment

including the emission control systems. This information is provided with all

Wacker Neuson engines/equipment at the time of purchase.

Exhaust Emissions

The combustion process produces carbon monoxide, oxides of nitrogen, and

hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important

because, under certain conditions, they react to form photochemical smog when

subjected to sunlight. Carbon monoxide does not react in the same way, but it is

toxic.

Wacker Neuson utilizes lean carburetor settings and other systems to reduce the

emissions of carbon monoxide, oxides of nitrogen, and hydrocarbons.

Evaporative Emissions

Evaporative emissions are fuel emissions and generally include emissions that

result from permeation of fuel through the fuel-system materials or from ventilation

of the fuel system.

Wacker Neuson utilizes low-permeation fuel lines and fuel tanks where applicable

to reduce evaporative emissions.

Problems that may affect Emissions

If any of the following symptoms arise, have the engine/equipment inspected and

repaired by a Wacker Neuson dealer/service center.

 Hard starting or stalling after starting

 Rough idling

 Misfiring or backfiring under load

 Afterburning (backfiring)

 Presence of black exhaust smoke during operation

 High fuel consumption

Emission Control Systems Information and Warranty

8 wc_tx001752gb.fm

Tampering and Altering

Tampering with or altering the emission control system may increase emissions

beyond the legal limit. If evidence of tampering is found, Wacker Neuson may deny

a warranty claim. Among those acts that constitute tampering are:

 Removing or altering of any part of the air intake, fuel, or exhaust systems.

 Altering or defeating the speed-adjusting mechanism causing the engine to

operate outside its design parameters.

Emission Control Systems Information and Warranty

wc_tx001752gb.fm 9

1.2 Limited Defect Warranty for Wacker Neuson Emission Control

Systems

The Emission Control Warranty is valid only for the U.S.A., its territories, and

Canada.

Wacker Neuson Sales Americas, LLC, N92 W15000 Anthony Avenue,

Menomonee Falls, WI 53051, (hereinafter “Wacker Neuson”) warrants to the initial

retail purchaser, and each subsequent owner, that this engine/equipment, including

all parts of its emission control systems, have been designed, built, and equipped

to conform at the time of initial sale to all applicable emission regulations of the

U.S. Environmental Protection Agency (EPA), and that the engine/equipment is

free of defects in materials and workmanship which would cause this engine/

equipment to fail to conform to EPA regulations during its warranty period.

Wacker Neuson is also liable for damages to other engine/equipment components

caused by a failure of any warranted parts during the warranty period.

Limited Defect Warranty Period for Wacker Neuson Emission Control

Systems

The warranty period for this engine/equipment begins on the date of sale to the

initial purchaser and continues for a minimum of two (2) years. For the warranty

terms for your specific engine/equipment, visit wackerneuson.com.

Any implied warranties are limited to the duration of this written warranty.

What is covered

Wacker Neuson recommends the use of genuine Wacker Neuson parts, or the

equivalent, whenever maintenance is performed. The use of replacement parts not

equivalent to the original parts may impair the effectiveness of the engine/

equipment emission controls systems. If such a replacement part is used in the

repair or maintenance of the engine/equipment, assure yourself that such part is

warranted by its manufacturer to be equivalent to the parts offered by Wacker

Neuson in performance and durability. Furthermore, if such a replacement part is

used in the repair or maintenance of the engine/equipment, and an authorized

Wacker Neuson dealer/service center determines it is defective or causes a failure

of a warranted part, the claim for repair of the engine/equipment may be denied. If

the part in question is not related to the reason the engine/equipment requires

repair, the claim will not be denied.

For the components listed in the following table, an authorized Wacker Neuson

dealer/service center will, at no cost to you, make the necessary diagnosis, repair,

or replacement necessary to ensure that the engine/equipment complies with the

applicable EPA regulations. All defective parts replaced under this warranty

become property of Wacker Neuson.

Emission Control Systems Information and Warranty

10 wc_tx001752gb.fm

Exhaust Emissions

* Indicates expendable maintenance items. Warranted only to first scheduled replacement point.

Evaporative Emissions

Systems Covered Components

Fuel metering system Carburetor and internal parts

Air/fuel ratio feedback system

(if applicable)

Cold start enrichment system

(if applicable)

Regulator assembly (if applicable)

Exhaust system Catalytic muffler (if applicable)

Exhaust manifold (if applicable)

Air induction system Air filter housing

Air filter element*

Intake manifold (if applicable)

Ignition system Flywheel magneto

Ignition module

Electronic controls (if applicable)

Spark advance/retard system (if

applicable)

Spark plug cap

Spark plug*

Miscellaneous parts associated with the

exhaust emission control system

Tubing

Fittings

Seals

Gaskets

Clamps

Systems Covered Components

Evaporative control system Fuel tank (if applicable)

Fuel tank cap (if applicable)

Fuel line (if applicable)

Fuel line fittings (if applicable)

Clamps (if applicable)

Carbon canister (if applicable)

Purge port connector (if applicable)

Miscellaneous parts associated with the

evaporative emission control system

Clamps

Gaskets

Mounting brackets

Emission Control Systems Information and Warranty

wc_tx001752gb.fm 11

What is not covered

 Failures other than those resulting from defects in material or workmanship.

 Any systems or parts which are affected or damaged by owner abuse,

tampering, neglect, improper maintenance, misuse, improper fueling,

improper storage, accident and/or collision; the incorporation of, or any use

of, add-on or modified parts, or unsuitable attachments, or the alteration of

any part.

 Replacement of expendable maintenance items made in connection with

required maintenance services after the item’s first scheduled replacement

as listed in the maintenance section of the engine/equipment operator’s

manual, such as spark plugs and filters.

 Incidental or consequential damages such as loss of time or the use of the

engine/equipment, or any commercial loss due to the failure of the engine/

equipment.

 Diagnosis and inspection charges that do not result in warranty-eligible

service being performed.

 Any non-authorized replacement part, or malfunction of authorized parts due

to use of-non authorized parts.

Owner’s Warranty Responsibility

The engine/equipment owner is responsible for the performance of the required

maintenance listed in the Wacker Neuson engine/equipment operator’s manual.

Wacker Neuson recommends that all receipts covering maintenance on the

engine/equipment be retained, but Wacker Neuson cannot deny warranty

coverage solely for the lack of receipts or for the failure to ensure the performance

of all scheduled maintenance.

Normal maintenance, replacement, or repair of emission control devices and

systems may be performed by any repair establishment or individual; however,

warranty repairs must be performed by an authorized Wacker Neuson dealer/

service center.

The engine/equipment must be presented to an authorized Wacker Neuson dealer/

service center as soon as a problem exists. Contact Wacker Neuson Product

Support Department (1-800-770-0957) or visit wackerneuson.com to find a dealer/

service center in your area, or to answer questions regarding warranty rights and

responsibilities.

How to Make a Claim

In the event that any emission-related part is found to be defective during the

warranty period, you shall notify Wacker Neuson Product Support Department (1-

800-770-0957), and you will be advised of the appropriate dealer/service center

where warranty repair can be performed. All repairs qualifying under this limited

warranty must be performed by an authorized Wacker Neuson dealer/service

center.

You must take your Wacker Neuson engine/equipment along with proof of original

purchase date, at your expense, to the authorized Wacker Neuson dealer/service

center during their normal business hours.

Emission Control Systems Information and Warranty

12 wc_tx001752gb.fm

For owners located more than 100 miles from an authorized dealer/service center

(excluding the states with high-altitude areas as identified in 40 CFR Part 1068,

Appendix III), Wacker Neuson will pay for pre-approved shipping costs to and from

an authorized Wacker Neuson dealer/service center.

Claims for repair or adjustment found to be caused solely by defects in material or

workmanship will not be denied because the engine/equipment was not properly

maintained and used.

The warranty repairs should be completed in a reasonable amount of time, not to

exceed 30 days.

BS 50-4s Safety Information

wc_si000403gb.fm 13

2 Safety Information

2.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all

safety messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information BS 50-4s

14 wc_si000403gb.fm

2.2 Machine Description and Intended Use

This machine is a vibratory rammer. The Wacker Neuson Rammer

consists of a gasoline or diesel engine, a clutch, a fuel tank, a spring-

loaded ramming system, a ramming shoe, and a handle. The engine

transmits power through the ramming system and ramming shoe,

generating percussive impact force to compact soil. The operator

guides and controls the machine from behind using the handle.

This machine is intended to be used for compacting cohesive, mixed,

and granular soils in confined areas.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine as a hammer or for other demolition work

• Attaching the machine to any other machine

• Operating the machine outside of factory specifications

• Operating machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Fire hazards from improper refueling techniques

• Fuel and its fumes

• Personal injury from improper lifting techniques or operating

techniques

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

BS 50-4s Safety Information

wc_si000403gb.fm 15

2.3 Safety Guidelines for Operating the Machine

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Operator training

Before operating the machine:

• Read and understand the operating instructions contained in all

manuals delivered with the machine.

• Familiarize yourself with the location and proper use of all

controls and safety devices.

• Contact Wacker Neuson for additional training if necessary.

When operating this machine:

• Do not allow improperly trained people to operate the machine.

People operating the machine must be familiar with the potential

risks and hazards associated with it.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

2.3.1 Never operate this machine in applications for which it is not intended.

2.3.2 Do not allow anyone to operate this equipment without proper training.

People operating this equipment must be familiar with the risks and

hazards associated with it.

2.3.3 Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

2.3.4 Do not operate the machine with unapproved accessories or

attachments.

2.3.5 Never leave the machine running unattended.

Safety Information BS 50-4s

16 wc_si000403gb.fm

2.3.6 Never tamper with or disable the function of operating controls.

2.3.7 Never use the choke to stop the engine.

2.3.8 Never operate the machine in areas where explosions may occur.

2.3.9 Read, understand, and follow procedures in the Operator’s Manual

before attempting to operate the machine.

2.3.10 Make sure that all other persons are at a safe distance from the

machine. Stop the machine if people step into the working area of the

machine.

2.3.11 Be sure operator is familiar with proper safety precautions and

operation techniques before using machine.

2.3.12 Always keep hands, feet, and loose clothing away from moving parts

of the machine.

2.3.13 Always use common sense and caution when operating the machine.

2.3.14 Always be sure the rammer will not tip over, roll, slide, or fall when not

being operated.

2.3.15 Always turn the engine OFF when the rammer is not being operated.

2.3.16 Always guide the rammer in such a way that the operator is not

squeezed between the rammer and solid objects. Special care is

required when working on uneven ground or when compacting coarse

material. Make sure to stand firmly when operating the machine under

such conditions.

2.3.17 When working near the edges of breaks, pits, slopes, trenches and

platforms, always operate the rammer in such a way that there is no

danger of it tipping over or falling in.

2.3.18 Store the machine properly when it is not being used. The machine

should be stored in a clean, dry location out of the reach of children.

2.3.19 Always operate machine with all safety devices and guards in place

and in working order. Do not modify or defeat safety devices. Do not

operate machine if any safety devices or guards are missing or

inoperative.

2.3.20 Do not transport the machine while it is running.

2.3.21 Do not tip the machine for cleaning or for any other reason.

BS 50-4s Safety Information

wc_si000403gb.fm 17

2.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information BS 50-4s

18 wc_si000403gb.fm

• Do not refuel if the machine is positioned in a truck fitted with a

plastic bed liner. Static electricity can ignite the fuel or fuel vapors.

2.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

Service training

Before servicing or maintaining the machine:

• Read and understand the instructions contained in all manuals

delivered with the machine.

• Familiarize yourself with the location and proper use of all

controls and safety devices.

• Only trained personnel shall troubleshoot or repair problems

occurring with the machine.

• Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

• Do not allow improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must

be familiar with the associated potential risks and hazards.

2.5.1 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

2.5.2 DO NOT operate the machine without an air cleaner.

2.5.3 DO NOT remove air cleaner cover, paper element, or precleaner while

engine is running.

2.5.4 DO NOT alter engine speeds. Run the engine only at speeds specified

in the Technical Data Section.

WARNING

BS 50-4s Safety Information

wc_si000403gb.fm 19

2.5.5 Do not crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

2.5.6 Do not test for spark on gasoline-powered engines if the engine is

flooded or the smell of gasoline is present. A stray spark could ignite

the fumes.

2.5.7 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

2.5.8 ALWAYS replace the safety devices and guards after repairs and

maintenance.

2.5.9 Keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

2.5.10 ALWAYS do periodic maintenance as recommended in the Operator’s

Manual.

2.5.11 ALWAYS clean debris from engine cooling fins.

2.5.12 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

2.5.13 Disconnect the spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

2.5.14 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

2.5.15 Do not operate the machine with unapproved accessories or

attachments.

Labels BS 50-4s

20 wc_si000495gb.fm

3 Labels

3.1 Label Locations

F

B

A

H

E

G

M

K

D

C

I

N

L

wc_gr007427

La page charge ...

Wacker Neuson BS50-4HO EU Manuel utilisateur

Ce manuel convient également à

Wacker Neuson BS50-4HO EU Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents