Pioneer AVIC 7100 NEX Le manuel du propriétaire

Black plate (1,1)

Installation Manual

Manuel d’installation

MULTIMEDIA NAVIGATION RECEIVER

RECEPTEUR DE NAVIGATION MULTIMEDIA

AVIC-8100NEX

AVIC-7100NEX

AVIC-6100NEX

AVIC-5100NEX

English Français

<CRD4852-A>1

Black plate (2,1)

Precautions

Your new product and this manual 3

Important safeguards 3

Connection

Precautions before connecting the

system 5

Before installing this product 5

To prevent damage 6

– Notice for the blue/white lead 6

Parts supplied 7

Connecting the power cord (1) 8

Connecting the power cord (2) 10

Connecting the system 12

Connecting to separately sold power

amp 14

Connecting an iPhone, iPod, Android device

or a MirrorLink™ device 15

Connecting an iPhone with Lightning

connector 17

– Connecting via the USB port 17

– Connecting via the HDMI port 17

– Connecting via the RGB input 18

Connecting an iPhone with 30-pin

connector 18

– Connecting via the AUX input 18

– Connecting via the RGB input 19

Connecting the Android™ device 19

– Connecting an Android device with an

HDMI port 19

– Connecting an Android device with an

MHL port 20

Connecting the Android or MirrorLink™

device 20

Securing the High Speed HDMI

®

Cable 21

Connecting a rear view camera 22

Connecting the external video

component 23

– Using AV input 23

– Using an AUX input 24

Connecting an HDMI device 25

Connecting the rear display 25

– When using a rear display connected to

rear video output 25

Installation

Precautions before installation 26

To avoid electromagnetic interference 26

Before installing 26

– For AVIC-8100NEX and AVIC-7100NEX

users 27

Installing this product 27

– Installation notes 27

– Parts supplied 28

– Installation using the screw holes on

the side of this product 28

– Fastening the detachable faceplate 29

Installing the GPS antenna 30

– Installation notes 30

– Parts supplied 30

– When installing the antenna inside the

vehicle (on the dashboard or rear

shelf) 31

Installing the microphone 32

– Parts supplied 32

– Mounting on the sun visor 32

– Installation on the steering column 33

– Adjusting the microphone angle 33

After installation

After installing this product 34

<CRD4852-A>2

Contents

En

2

Black plate (3,1)

Your new product and this

manual

! The navigation features of this product

(and the rear view camera option if pur-

chased) are intended solely to aid you in

the operation of your vehicle. It is not a sub-

stitute for your attentiveness, judgment

and care when driving.

! Never use this product to route to hospi-

tals, police stations, or similar facilities in

an emergency. Please call the appropriate

emergency number.

! Do not operate this product, any applica-

tions, or the rear view camera option (if pur-

chased) if doing so will divert your attention

in any way from the safe operation of your

vehicle. Always observe safe driving rules

and follow all existing traffic regulations. If

you experience difficulty in operating this

product or reading the display, park your

vehicle in a safe location and apply the

parking brake before making the necessary

adjustments.

! This manual explains how to install this

product in your vehicle. Operation of this

product is explained in the separate man-

uals.

! Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including

airbags, hazard lamp buttons, or (iii) impair

the driver’s ability to safely operate the vehi-

cle. In some cases, it may not be possible

to install this product because of the vehi-

cle type or the shape of the vehicle interior.

! Model icons shown in this manual indicate

that the description is intended for the

models indicated by the icons.

If the following icon is shown, the descrip-

tion is applied only to the model shown.

e.g.)

8100NEX

Important safeguards

WARNING

Pioneer does not recommend that you install

this product yourself. This product is de-

signed for professional installation only. We

recommend that only authorized Pioneer ser-

vice personnel, who have special training

and experience in mobile electronics, set up

and install this product. NEVER SERVICE

THIS PRODUCT YOURSELF. Installing or

servicing this product and its connecting

cables may expose you to the risk of electric

shock or other hazards, and can cause da-

mage to this product that is not covered by

warranty.

! Read this manual fully and carefully before

installing this product.

! Keep this manual handy for future refer-

ence.

! Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

! This product may in certain circumstances

display inaccurate position of your vehicle,

the distance of objects shown on the

screen, and compass directions. In addi-

tion, the system has certain limitations, in-

cluding the inability to identify one-way

streets, temporary traffic restrictions and

potentially unsafe driving areas. Please ex-

ercise your own judgment in the light of ac-

tual driving conditions.

! As with any accessory in your vehicle’s in-

terior, this product should not divert your

attention from the safe operation of your

vehicle as it may result in serious injury or

death. If you experience difficulty in operat-

ing the system or reading the display,

please make adjustments while safely

parked.

! Please remember to wear your seat belt at

all times while operating your vehicle. If

you are in an accident, your injuries can be

considerably more severe if your seat belt

is not properly buckled.

<CRD4852-A>3

En

3

English

Section

01

Precautions

Black plate (4,1)

! Certain country and government laws may

prohibit or restrict the placement and use

of this product in your vehicle. Please com-

ply with all applicable laws and regulations

regarding the use, installation and opera-

tion of this product.

<CRD4852-A>4

En

4

Section

01

Precautions

Black plate (5,1)

Precautions before

connecting the system

WARNING

Do not take any steps to tamper with or dis-

able the parking brake interlock system

which is in place for your protection. Tamper-

ing with or disabling the parking brake inter-

lock system could result in serious injury or

death.

CAUTION

! If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

! Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

! Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

! It is extremely dangerous to allow cables

to become wound around the steering col-

umn or shift lever. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or hin-

der driving.

! Make sure that the cables and wires will

not interfere with or become caught in

any of the vehicle’s moving parts, espe-

cially the steering wheel, shift lever, park-

ing brake, sliding seat tracks, doors, or

any of the vehicle’s controls.

! Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

! Do not cut the GPS antenna cable to

shorten it or use an extension to make it

longer. Altering the antenna cable could

result in a short circuit or malfunction.

! Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

! Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of this product and tap-

ping into the lead. The current capacity of

the lead will be exceeded, causing over-

heating.

Before installing this product

! Use this unit with a 12-volt battery and ne-

gative grounding only. Failure to do so may

result in a fire or malfunction.

! To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore installation.

<CRD4852-A>5

En

5

English

Section

02

Connection

Black plate (6,1)

To prevent damage

WARNING

! Use speakers over 50 W (output value)

and between 4 W to 8 W (impedance value).

Do not use 1 W to 3 W speakers for this

unit.

! The black cable is ground. When instal-

ling this unit or power amp (sold sepa-

rately), make sure to connect the ground

wire first. Ensure that the ground wire is

properly connected to metal parts of the

car’s body. The ground wire of the power

amp and the one of this unit or any other

device must be connected to the car sepa-

rately with different screws. If the screw

for the ground wire loosens or falls out, it

could result in fire generation of smoke or

malfunction.

Ground wire

Metal parts of car’s bod

y

Power amp

Other devices

(Another electronic

device in the car)

*1

Not supplied for this unit.

! When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

! When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

! This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

A

C

O

N

S

T

A

R

T

O

F

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

! Attach the connectors of the same color to

the corresponding colored port, i.e., blue

connector to the blue port, black to black,

etc.

! Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

! Since a unique BPTL circuit is employed,

do not directly ground the * side of the

speaker lead or connect the * side of an-

other side of the speaker lead together. Be

sure to connect the * side of the speaker

lead to the * side of the speaker lead on

this product.

Notice for the blue/white lead

! When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal, the auto-antenna relay control term-

inal, or the antenna booster power control

terminal (max. 300 mA 12 V DC). The con-

trol signal is output through the blue/white

lead, even if the audio source is switched

off.

! Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

! Be sure not to use this lead as the power

supply lead for the auto-antenna or anten-

na booster. Such connection could cause

excessive current drain and malfunction.

<CRD4852-A>6

En

6

Section

02

Connection

Black plate (7,1)

Parts supplied

Parts marked (*) are supplied with AVIC-

8100NEX, AVIC-7100NEX and AVIC-6100NEX.

This product Power cord

GPS antenna Microphone

Mini-jack extension

cable

USB cable

Lock tie*

<CRD4852-A>7

En

7

English

Section

02

Connection

Black plate (8,1)

Connecting the power cord (1)

















Yellow

To terminal supplied with power regardless of

ignition switch position.

Red

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

With a two-speaker system, do not connect anything

to the speaker leads that are not connected to

speakers.

White

Gray

Front speakerFront speaker

White/black Gray/black

Left Right

Rear speaker Rear speaker

Green

Violet

Green/black

Violet/black

<CRD4852-A>8

En

8

Section

02

Connection

Black plate (9,1)

Audio source will be set to mute or attenuate, while

the following sounds will not be muted or

attenuated. For details, refer to Operation Manual.

—

Voice guidance of the navigation

—

Incoming ring tone and incoming voice of the

cellular phone that is connected to this product

via Bluetooth wireless technology

Note

Yellow/black (MUTE)

If you use equipment with a mute

function, connect that equipment to

the Audio Mute lead. If not, keep the

Audio Mute lead free of any

connections.

Blue/white (SYSTEM REMOTE CONTROL)

To auto-antenna relay control terminal or antenna

booster power control terminal (max. 300 mA 12 V DC).

If the vehicle has a glass antenna, connect to the

antenna booster power control terminal (max. 300 mA

12 V DC).

This product

Fuse (10 A)

Power cord

14 cm (5-1/2 in.)

Power supply

<CRD4852-A>9

En

9

English

Section

02

Connection

Black plate (10,1)

Connecting the power cord (2)

IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING

ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE VEHICLE´S

ANTILOCK BRAKING SYSTEM, AUTOMATIC TRANSMISSION AND SPEEDOMETER

INDICATION.

Pink (CAR SPEED SIGNAL INPUT)

This product is connected here to detect the distance the vehicle travels. Always connect the

vehicle’s speed detection circuit. Failure to make this connection will increase errors in the

vehicle’s location display.

LIGHT GREEN LEAD AT POWER CONNECTOR IS

DESIGNED TO DETECT PARKED STATUS AND

MUST BE CONNECTED TO THE POWER SUPPLY

SIDE OF THE PARKING BRAKE SWITCH.

IMPROPER CONNECTION OR USE OF THIS

LEAD MAY VIOLATE APPLICABLE LAW AND MAY

RESULT IN SERIOUS INJURY OR DAMAGE.

Light green (PARKING BRAKE)

Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply

side of the parking brake switch.

If this connection is made incorrectly or omitted, certain functions of this product will be

unusable.

The position of the speed detection circuit and the position of the parking brake switch

vary depending on the vehicle model. For details, consult your authorized Pioneer dealer

or an installation professional.

Power supply side

Ground side

Parking brake switch

WARNING

CAUTION

Note

WARNING

It is strongly suggested that the speed pulse wire be connected for accuracy of navigation

and better performance.

<CRD4852-A>10

En

10

Section

02

Connection

Black plate (11,1)

Violet/white (REVERSE-GEAR SIGNAL INPUT)

This is connected so that this product can detect whether

the vehicle is moving forwards or backwards. Connect the

violet/white lead to the lead whose voltage changes when

the shift lever is put in reverse. Unless connected, the

sensor may not detect your vehicle traveling

forward/backward properly, and thus the position of your

vehicle detected by the sensor may be misaligned from the

actual position.

When you use a rear view camera, please make

sure to connect this lead. Otherwise you cannot

switch to the rear view camera picture.

Note

This product

Power cord

Power supply

<CRD4852-A>11

En

11

English

Section

02

Connection

Black plate (12,1)

Connecting the system

This product

Wired remote input

Please refer to the instruction manual for

the Hard-wired remote control adapter

(sold separately).

SiriusXM Connect Vehicle Tuner

Please refer to the instruction manual

for SiriusXM Connect Vehicle Tuner

(sold separately).

WARNING

· To avoid the risk of accident and the potential violation of applicable laws, this

product should never be used while the vehicle is being driven except for

navigation purposes. And, also rear displays should not be in a location where it

is a visible distraction to the driver.

· In some countries, the viewing of images on a display inside a vehicle even by

persons other than the driver may be illegal. Where such regulations apply they

must be obeyed and this product’s video source should not be used.

3.55 m (11 ft. 8 in.)

GPS antenna

Antenna jack

Vehicle antenna

Microphone

4 m (13 ft. 1 in.)

iDatalink adapter input

Please refer to the instruction

manual for the iDatalink adapter

(sold separately).*

<CRD4852-A>12

En

12

Section

02

Connection

Black plate (13,1)

Notes

!

*

Before using and/or connecting the iData-

link Maestro adapter, you will need to first

flash the Maestro module with the appropriate

vehicle and head unit firmware. You can find

the device number that is required for the acti-

vation on the followings (refer to Operation

Manual.):

— the label on the packaging of this product

— the label on this product

— the “Firmware Information” screen

8100NEX 7100NEX

! Make sure to connect the microphone sup-

plied with this product when using Android

Auto.

<CRD4852-A>13

En

13

English

Section

02

Connection

Black plate (14,1)

Connecting to separately sold power amp

























System remote control

Power cord

Blue/white

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Front speaker

Rear speaker

Subwoofer

RCA

cables

(sold separately)

This product

15 cm (5-7/8 in.)

Rear outputs

(REAR OUTPUT)

Front outputs

(FRONT OUTPUT)

To system control terminal of the power amp

(max. 300 mA 12 V DC).

White, Red (SWL, SWR)

Notes

· You can change the RCA output of the subwoofer depending on your subwoofer

system. (Refer to Operation Manual.)

· The subwoofer output of this product is monaural.

Power supply

<CRD4852-A>14

En

14

Section

02

Connection

Black plate (15,1)

Connecting an iPhone, iPod, Android device or a

MirrorLink

™

device

Find your device and the function you want to operate from the list below, and refer to the page for the connection.

iPhone 6 Plus/iPhone 6/iP hone 5s/iPhone 5c/iPhone 5

iPod (audio) Refer to Connecting via the USB port on page 17.

AppRadio Mode

8100NEX 7100NEX 6100NEX

Refer to Connecting via the HDMI port on page 17.

5100NEX

Refer to Connecting via the RGB input on page 18.

Note

For any of the connections mentioned above, aha, AVICSYNC App and Pandora are available for use.

iPhone 3GS/iPod touch (2nd and 3rd generation)/iPod classic 160GB/iPod classic 80GB/iPod nano (3rd,

4th, 5th, and 6th generation)

Refer to Connecting via the AUX input on page 18.

iPhone 4s/iPhone 4/iPod touch (4th generation)

Refer to Connecting via the RGB input on page 19.

iPod touch (5th generation)

iPod (audio) Refer to Connecting via the USB port on page 17.

AppRadio Mode

8100NEX 7100NEX 6100NEX

Refer to Connecting via the HDMI port on page 17.

5100NEX

Refer to Connecting via the RGB input on page 18.

iPod nano (7th generation)

Refer to Connecting via the USB port on page 17.

<CRD4852-A>15

En

15

English

Section

02

Connection

Black plate (16,1)

Android device

8100NEX 7100NEX 6100NEX

AppRadio Mode

HDMI port

Refer to Connecting an Android device with an HDMI port on page 19.

MHL port

Refer to Connecting an Android device with an MHL port on page 20.

8100NEX 7100NEX

Android Auto

Refer to Connecting the Android or MirrorLink

™

device on page 20.

Note

For any of the connections mentioned above, aha, AVICSYNC App and Pandora are available for use.

MirrorLink device

Refer to Connecting the Android or MirrorLink

™

device on page 20.

<CRD4852-A>16

En

16

Section

02

Connection

Black plate (17,1)

Connecting an iPhone with

Lightning connector

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the

manual for the cable.

! For details concerning the connection, opera-

tions and compatibility of iPhone, refer to Op-

eration Manual.

Connecting via the USB port

The USB interface cable for iPod / iPhone (CD-

IU52) (sold separately) is required for the con-

nection.

USB cable

1.5 m (4 ft. 11 in.)

USB interface cable for iPod / iPhone

(CD-IU52) (sold separately)

This product

USB port 1

iPhone with

Lightning connector

USB port 2

Connecting via the HDMI port

8100NEX 7100NEX

6100NEX

The following cables are required for the con-

nection.

! HDMI interface cable for iPod / iPhone

(CD-IH202) (sold separately)

! USB interface cable for iPod / iPhone (CD-

IU52) (sold separately)

! Lightning Digital AV Adapter (Apple Inc.

products) (sold separately)

USB cable

1.5 m (4 ft. 11 in.)

This product

USB port 1

USB interface cable for iPod / iPhone

(CD-IU52) (sold separately)

iPhone with

Lightning connector

High Speed HDMI

®

Cable

(Type A - A)

(supplied with CD-IH202)

HDMI port

Lightning Digital AV Adapter

(Apple Inc. products)

(sold separately)

<CRD4852-A>17

En

17

English

Section

02

Connection

Black plate (18,1)

Note

! When you connect the High Speed HDMI

®

Cable, use the lock tie to fix it securely.

= For details, refer to Securing the High

Speed HDMI

®

Cable on page 21.

Connecting via the RGB input

5100NEX

The following cables are required for the con-

nection.

! VGA/USB interface cable for iPod / iPhone

(CD-IV202AV) (sold separately)

! USB interface cable for iPod / iPhone (CD-

IU52) (sold separately)

! Lightning to VGA Adapter (Apple Inc. pro-

ducts) (sold separately)

Lightning to VGA Adapter

(Apple Inc. products)

(sold separately)

VGA/USB interface cable

for iPod / iPhone

(CD-IV202AV) (sold separately)

iPhone with

Lightning connector

This product

USB interface cable for iPod / iPhone

(CD-IU52) (sold separately)

USB port 1

RGB input

Connecting an iPhone with

30-pin connecto r

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the

manual for the cable.

! For details concerning the connection, opera-

tions and compatibility of iPhone, refer to Op-

eration Manual.

Connecting via the AUX input

The USB interface cable for iPod / iPhone (CD-

IU201V) (sold separately) is required for the

connection.

This product

USB interface cable for iPod / iPhone

(CD-IU201V) (sold separately)

USB cable

1.5 m

(4 ft. 11 in.)

iPhone with

30-pin connector

AUX input

USB port 1

USB port 2

Mini-jack extension cable

2 m (6 ft. 7 in.)

Note

Connect the USB cable to USB port 1 when using

“aha” or “Pandora” as the source.

<CRD4852-A>18

En

18

Section

02

Connection

Black plate (19,1)

Connecting via the RGB input

The USB interface cable for iPod / iPhone (CD-

IU201S) (sold separately) is required for the

connection.

USB cable

1.5 m (4 ft. 11 in.)

USB interface cable for iPod / iPhone

(CD-IU201S) (sold separately)

This product

USB port 1

RGB input

iPhone with

30-pin connector

Connecting the Android

™

device

8100NEX 7100NEX

6100NEX

App Connectivity Kit (CD-AH200) (sold sepa-

rately) is required for the connection.

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the

manual for the cable.

! For details concerning the connection and op-

erations of Android device, refer to Operation

Manual.

! When you connect the High Speed HDMI

®

Cable, use the lock tie to fix it securely.

= For details, refer to Securing the High

Speed HDMI

®

Cable on page 21.

Connecting an Android device

with an HDMI port

USB cable

(supplied with

CD-AH200)

This product

Android device

High Speed HDMI

®

Cable (Type A - A)

(supplied with

CD-AH200)

USB port 2

HDMI port

USB - micro USB cable

(Type USB A - micro USB B)

(supplied with CD-AH200)

Adapter cable

(HDMI Type A - D)

(supplied with CD-AH200)

<CRD4852-A>19

En

19

English

Section

02

Connection

Black plate (20,1)

Connecting an Android device

with an MHL port

USB cable

(supplied with

CD-AH200)

This product

Android device

USB port 2

HDMI port

High Speed HDMI

®

Cable

(Type A - A)

(supplied with CD-AH200)

USB - micro USB cable

(Type USB A - micro USB B)

(supplied with CD-AH200)

MHL adapter

(supplied with

CD-AH200)

Connecting the Android or

MirrorLink

™

device

The USB interface cable for use with Android

or MirrorLink

™

devices (CD-MU200) (sold sepa-

rately) is required for the connection.

USB cable

(supplied with CD-MU200)

USB - micro USB cable

(Type USB A - micro USB B)

(supplied with CD-MU200)

This product

Android or MirrorLink device

USB port 2

Note

For details on how to connect an external device

using a separately sold cable, refer to the manual

for the cable.

<CRD4852-A>20

En

20

Section

02

Connection

La page charge ...

Pioneer AVIC 7100 NEX Le manuel du propriétaire

Pioneer AVIC 7100 NEX Le manuel du propriétaire

dans d''autres langues

Documents connexes