Panasonic PVDC152 Le manuel du propriétaire

Catégorie
Caméscopes
Taper
Le manuel du propriétaire

Ce manuel convient également à

R
Spanish Quick Use Guide is included.
Guía para rápida consulta en español está incluida.
LSQT0559A
For USA assistance, please call: 1-800-211-PANA(7262) or send e-mail to : [email protected]
For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca
Digital Video Camcorder
Operating Instructions
Models No.
PV-DC152
PV-DC252
PV-DC152-K
PV-DC252-K
Before attempting to connect, operate or adjust this product, please read these instructions thoroughly.
Mini
2
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock.
Therefore, it is dangerous to make any kind
of contact with any inside part of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
Things You Should Know
Thank you for choosing Panasonic!
You have purchased one of the most sophisticated and
reliable products on the market today. Used properly, were
sure it will bring you and your family years of enjoyment.
Please take time to fill in the information on the right.
The serial number is on the tag located on the underside of
your Palmcorder. Be sure to retain this manual as your
convenient Palmcorder information source.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Safety Precautions
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
Your
Palmcorder is designed to record and play back in Standard Play (SP) mode and Long Play (LP) mode.
It is recommended that only cassette tapes that have been tested and inspected for use in Palmcorder with the
mark be used.
The above markings are located on the appliance bottom cover.
Note: This equipment has been tested and found to comply with Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when operated in a residential environment.
If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off
and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. You may find the booklet, Something About
Interference available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC compliance, the user must use only the provided shielded interfacing cable with ferrite core when
connecting digital Palmcorder to computer in accordance with instruction herein. Also, any unauthorized changes or
modifications to this equipment could void the users authority to operate.
Declaration of Conformity
Model No.: PV-DC152/PV-DC252
Trade Name: Panasonic
Responsible party: Matsushita Electric Corporation of America
Address: One Panasonic Way, Secaucus, New Jersey 07094
Telephone number: 1-800-211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED
ACCESSORIES ONLY.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR
EQUIVALENT TYPE.
Since this product gets hot during use, operate it in well ventilated place; do not install this equipment in a confined space such
as a bookcase or similar unit.
Ò
Ò
3
Important Safeguards
1) Read InstructionsAll the safety and operating
instructions should be read before the unit is operated.
2) Retain InstructionsThe safety and operating
instructions should be retained for future reference.
3) Heed WarningsAll warnings on the unit and in the
operating instructions should be adhered to.
4) Follow InstructionsAll operating and maintenance
instructions should be followed.
5) CleaningUnplug this video unit from the wall outlet
before cleaning. Do not use liquid or aerosol cleaners.
Use a dry cloth for cleaning.
6) AttachmentsDo not use attachments not
recommended by the video product manufacturer as
they may be hazardous.
7) Water and MoistureDo not use this video unit near
water- for example near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, and the like.
8) AccessoriesDo not place this video unit on an
unstable cart, stand, tripod, bracket, or table. The video
unit may fall, causing serious injury to a child or adult,
and serious damage to the unit. Use only with a cart,
stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the video unit. Any mounting
of the unit should follow the manufacturers instructions
and should use a mounting accessory recommended by
the manufacturer. An appliance
and cart combination should be
moved with care. Quick stops,
excessive force, and uneven
surfaces may cause the
appliance and cart combination
to overturn.
9) VentilationSlots and
openings in the cabinet are
provided for ventilation and to ensure reliable operation
of the video unit and to protect it from overheating.
These openings must not be blocked or covered. Never
place the video unit on a bed, sofa, rug, or other similar
surface, or near or over a radiator or heat register. This
video unit should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is
provided or the manufacturers instructions have been
adhered to.
10) Power SourcesThis video unit should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For video units intended to be operated from
battery power, or other sources, refer to the operating
instructions.
11) Grounding or PolarizationThis video unit may be
equipped with either a polarized 2-wire AC (Alternating
Current) line plug (a plug having one blade wider than
the other) or 3-wire grounding type plug, a plug having a
third (grounding) pin.
The 2-wire polarized plug will fit into the power outlet
only one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the
plug. If the plug still fails to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
The 3-wire grounding type plug will fit into a grounding
type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the grounding type plug.
12) Power-Cord ProtectionPower-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords of plugs, convenience
receptacles, and the point where they exit from the unit.
13) Outdoor Antenna GroundingIf an outside antenna or
cable system is connected to the video unit, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up
static charges. Part 1 of the Canadian Electrical Code, in
USA Section 810 of the National Electrical Code,
provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-
in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements
for the grounding electrode.
14) LightningFor added protection of this video unit
receiver during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the video unit
due to lightning and power-line surges.
15) Power LinesAn outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with
them might be fatal.
16) OverloadingDo not overload wall outlets and
extension cords as this can result in a risk of fire or
electric shock.
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810 - 20)
GROUNDING CONDUCTORS
(NEC SECTION 810 - 21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PARTH)
NEC - NATIONAL ELECTRICAL CODE
ELECTRIC
SERVICE
EQUIPMENT
S3125A
4
Important Safeguards
17) Objects and Liquids Never push objects of any kind
into this video unit through openings as they may touch
dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any
kind onto the video unit.
18) Servicing Do not attempt to service this video unit
yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
19) Damage Requiring Service Unplug this video unit
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If any liquid has been spilled into, or objects have
fallen onto, the video unit.
c. If the video unit has been exposed to rain or water.
d. If the video unit does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the video unit to its
normal operation.
e. If the video unit has been dropped or the cabinet has
been damaged.
f. When the video unit exhibits a distinct change in
performance this indicates a need for service.
20) Replacement Parts When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
21) Safety Check Upon completion of any service or
repairs to this video unit, ask the service technician to
perform safety checks to determine that the video unit is
in safe operating order.
Precautions
USE & LOCATION
TO AVOID SHOCK HAZARD ... Your Palmcorder and
power supply should not be exposed to rain or moisture.
Do not connect the power supply or operate your
Palmcorder if it gets wet. Your Palmcorder has been
designed for outdoor use, however it is not designed to
sustain direct exposure to water, rain, sleet, snow, sand,
dust, or a direct splashing from a pool or even a cup of
coffee. This action could permanently damage the internal
parts of your Palmcorder. Do not attempt to disassemble
this unit. There are no user serviceable parts inside.
Unplug your Palmcorder from the power supply before
cleaning.
DO NOT AIM YOUR PALMCORDER AT THE SUN OR
OTHER BRIGHT OBJECTS
DO NOT LEAVE THE PALMCORDER WITH THE EVF
AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE
DAMAGE TO THE INTERNAL PARTS OF THE EVF
DO NOT EXPOSE YOUR PALMCORDER TO
EXTENDED HIGH TEMPERATURE ... Such as, in direct
sunlight, inside a closed car, next to a heater, etc... This
action could permanently damage the internal parts of your
Palmcorder.
AVOID SUDDEN CHANGES IN TEMPERATURE ... If the
unit is suddenly moved from a cold place to a warm place,
moisture may form on the tape and inside the unit.
DO NOT LEAVE YOUR PALMCORDER OR THE POWER
SUPPLY TURNED ON WHEN NOT IN USE.
STORAGE OF YOUR PALMCORDER ... Store and handle
your Palmcorder in a manner that will not subject it to
unnecessary movement (avoid shaking and striking). Your
Palmcorder contains a sensitive pick-up device which
could be damaged by improper handling or storage.
CARE
TO CLEAN YOUR PALMCORDER ... Do not use strong or
abrasive detergents when cleaning your Palmcorder body.
TO PROTECT THE LENS ... Do not touch the surface of
the lens with your hand. Use a commercial Palmcorder
lens solution and lens paper when cleaning the lens.
Improper cleaning can scratch the lens coating.
TO PROTECT THE FINISH OF YOUR PALMCORDER ...
Before handling your Palmcorder, make sure your hands
and face are free from any chemical products, such as
suntan lotion, as it may damage the finish.
A lithium ion/polymer battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
A TTENTION:
This Product has a fluorescent lamp that contains a small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or
recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org
.>
This class B digital apparatus complies with CANADIAN ICES-003.
5
Contents
Before Using
Before Using........................................................................ 6
Standard Accessories ......................................................... 6
Quick Guide......................................................................... 7
To View the Playback Picture.............................................. 7
Controls and Components................................................... 8
Remote Controller ............................................................. 10
Power Supply .................................................................... 12
Charging Time and Available Recording Time.................. 12
Lens Cap and Grip Belt..................................................... 13
Attaching the Shoulder Strap ............................................ 13
Inserting a Cassette .......................................................... 13
Turning on/off the Palmcorder and Selecting Modes ........ 14
Using the Viewfinder ......................................................... 14
Using the LCD Monitor ...................................................... 14
Using the Menu Screen..................................................... 15
List of Menus..................................................................... 16
Setting Date and Time....................................................... 19
Internal Lithium Battery Recharge..................................... 19
LP Mode ............................................................................ 19
Audio Recording Mode...................................................... 19
CAMERA Mode
Recording .......................................................................... 20
PhotoShot Recording on the DV Cassette ........................ 21
Zoom In/Out Functions...................................................... 21
Digital Zoom Function ....................................................... 22
Digital Electronic Image Stabilizer Function...................... 22
Fade In/Out Functions....................................................... 22
Cinema Function ............................................................... 23
Backlight Compensation Function..................................... 23
Magic Pix Function............................................................ 23
Quick Start......................................................................... 24
Wind Noise Reduction Function........................................ 24
Recording in Special Situations......................................... 24
Manual Shutter Speed Adjustment.................................... 25
Manual Iris Adjustment (F Number) .................................. 25
Manual Focus Adjustment................................................. 25
Recording in Natural Colors (White Balance).................... 26
Adjusting White Balance Manually.................................... 26
Digital Effect Functions...................................................... 27
VCR Mode
Playing Back...................................................................... 29
Finding a Scene You Want to Play Back........................... 29
Slow Motion Playback ....................................................... 30
Still Playback/Still Advance Playback................................ 30
Finding the End of a Recording......................................... 30
Index Search Functions..................................................... 31
Playback Zoom Function................................................... 32
Playback Digital Effect Functions ...................................... 32
Playing Back on Your TV .................................................. 33
Audio Dubbing................................................................... 33
Special Features
Using a Memory Card........................................................34
Recording on the Memory Card.........................................34
Playing Back Files from the Memory Card ........................36
Copying Pictures from a Memory Card to a Cassette .......37
Slide Show.........................................................................38
Creating a Title ..................................................................39
Inserting a Title ..................................................................39
Protecting the Files on a Memory Card from Accidental
Erasure (File Lock).........................................................40
Deleting the Files recorded on a Memory Card ................. 40
Formatting a Memory Card................................................ 41
DPOF Setting..................................................................... 41
Copying your DV Cassette to an S-VHS or VHS Cassette
(Dubbing) .......................................................................42
Using your Palmcorder with Digital Video Equipment
(Dubbing) .......................................................................43
Using the Software with a Computer .................................44
ArcSoft Software................................................................45
Using the Supplied USB Connection Kit............................46
Installing USB Driver..........................................................46
Connecting Computer and Palmcorder .............................46
Check if Palmcorder is correctly recognized......................47
To disconnect USB cable safely ........................................47
Verifying and updating driver .............................................48
If you no longer need software or driver (uninstall)............51
Notes .................................................................................52
Others
Indications..........................................................................53
Warning/Alarm Indications.................................................55
Notes & Precautions..........................................................56
Cautions for Use ................................................................60
Explanation of Terms.........................................................63
Specifications.....................................................................64
Palmcorder Accessory System..........................................65
Palmcorder Accessory Order Form
(For USA Customers) ....................................................66
Before Requesting Service
(Problems and Solutions)...............................................67
Request for Service Notice ................................................69
Limited Warranty (For USA Customers)............................70
Customer Services Directory .............................................71
Warranty (For Canadian Customers).................................72
Index ..................................................................................73
Spanish Quick Use Guide/
Guía española para el uso rápido..................................74
6
K2KC4CB00002
CR2025
PV-DAC11 (For USA)
PV-DAC11-K (For Canada)
RP-SD008BVE0
VFC3506
N2QAEC000003 N2QCAD000001
1)
2)
3)
6)
5)
4)
7)
8)
9) 10)
CGR-D08R
LSFT0489 VFA0366
VFC3815
Before Using
Before Using
These operating Instructions are designed for use with models PV-DC252/
PV-DC252-K and PV-DC152/PV-DC152-K. Pictures may be slightly different
from the original.
The illustrations used in these Operating Instructions show model
PV-DC252, however, parts of the explanation refer to different models.
Depending on the model, some functions are not available.
Features may vary, so please read carefully.
Standard Accessories
Illustrated on the left are accessories packaged with the Palmcorder.
1) AC Adaptor, DC Cable and AC Cable (l 12)
Supplies power to the Palmcorder.
CAUTION:
This unit will operate on 110/120/220/240 V AC. An AC plug adaptor
may be required for voltages other than 120 V AC. Please contact
either a local or foreign electrical parts distributor for assistance in
selecting an alternate AC plug. We recommend using the accessory
power plug adaptor (VJSS0070) in an area which has special AC
outlets.
2) Battery Pack (l 12)
Supplies power to the Palmcorder.
3) Remote Controller and Button-Type Battery (l 10, 11)
4) Tethered Remote Control
5) Lens Cap and Lens Cap String (l 13)
6) A/V Cable (l 33)
7) Shoulder Strap (l 13)
8) SD Memory Card (l 52) (PV-DC252/PV-DC252-K)
9) CD-ROM (PV-DC252/PV-DC252-K):
USB Driver for Panasonic DVC (l 46)
G726 Decoder (l 44)
ArcSoft Software (l 44, 45)
Microsoft
®
and Windows
®
are registered trademarks of Microsoft in the
United States and other countries.
Macintosh is a registered trademark of Apple Computer, Inc. 2001. ArcSoft,
the ArcSoft logo, ArcSoft PhotoImpression 3.0, ArcSoft Photo Base 3.0,
ArcSoft Panorama Maker 3.0 and ArcSoft PhotoPrinter 2000 Pro are
trademarks of ArcSoft, Inc.
All product/brand names are trademarks or registered trademarks of the
respective holders.
Intel
®
Pentium
®
is a registered trademark.
i.LINK and ¥ are trademarks.
IBM is a registered trademark of IBM Company.
MultiMediaCard is a registered trademark.
SD is a trademark.
10) USB Cable (l 46) (PV-DC252/PV-DC252-K)
7
1
2
3
4
5, 6
OPEN/
OPEN/
EJECT
EJECT
CLOSE
PUSH
1
2
O
F
F
O
N
M
O
D
E
4
CAMERA
VCR
CARD
P.B.
3
CAMERA
VCR
CARD
P.B.
5
9
8
SEARCH
BACKLIGHT
FADE
MAGICPIX
MULTI/
P-IN-P
TITLE
CAMERA
STILL
SEARCH
67
O
F
F
O
N
M
O
D
E
Quick Guide
1
Charge the Battery.
(l 12)
Connect the AC Cable to the AC Adaptor and plug it into the AC Wall
Outlet.
Attach the Battery to the AC Adaptor. (This will start the charging
process.)
The [POWER] Lamp and [CHARGE] Lamp lights up, and charging
starts.
When the [CHARGE] Lamp goes off, charging is completed.
Since the Battery will not be charged when the DC Cable is connected
to the AC Adaptor, disconnect it.
2
Attach the Charged Battery to the Palmcorder.
(l 12)
3
Insert the Cassette.
(l 13)
Slide the [OPEN/EJECT]
1
Lever toward the front and pull down to
open the Cassette Compartment.
Insert the Cassette.
Press the [PUSH CLOSE]
2
to load the Cassette.
Close the outside compartment Cover.
4
Start recording.
(l 20)
Turn the Palmcorder on. (l 14)
Rotate the Switch
3
to [ON]. (The [CAMERA] Lamp lights up.)
Press the
4
Button. (Recording starts.)
Press the
4
Button again to pause the recording.
To View the Playback Picture
5
Switch to the VCR Mode, rewind the tape, and play the tape
back.
(l 29)
Set the
5
Switch to VCR mode. (The [VCR] Lamp lights up.)
Press the
6
Button. (Rewind the tape.)
Press the
7
Button. (Playback starts.)
Press the
8
Button. (Playback stops.)
6
Turn the Palmcorder off.
(l 14
)
Set the
9
Switch to [OFF].
8
Controls and Components
1) LCD Monitor (l 14)
................................................................................................................................
................................................................................................................................................................................................................................................................
.....................................................................................................................................................................
..........................................................................
.....................................
Due to limitations in LCD production technology, there may be some
tiny bright or dark spots on the LCD Monitor screen. However, this is
not a malfunction and does not affect the recorded picture.
......................................................................................................................................................................
2) LCD Monitor Open Tab [OPEN 4] (l 14, 62)
3) Accessory Shoe
Accessories, such as a stereo microphone (not supplied), are attached
here.
4) Rewind/Review Button [6] (l 29)
Reverse Search Button [SEARCHs] (l 20)
Recording Check Button [S] (l 20)
5) Play Button [1] (l 29, 36, 38)
Backlight Button [BACKLIGHT] (l 23)
6) Fast Forward/Cue Button [5]
(l 29)
Forward Search Button [SEARCHr] (l 20)
7) Stop Button [] (l 29, 36, 38)
Fade Button [FADE] (l 22)
8) Still Button [;] (l 30, 36)
Camera Still Button [CAMERA STILL] (l 21)
9) MAGICPIX Button [MAGICPIX] (l 23)
10) Title Button [TITLE] (PV-DC252/PV-DC252-K) (l 39)
11) Multi-Picture Button [MULTI] (l 28, 39)
Picture-in-Picture Button [P-IN-P] (l 28)
12) Tape/Card PhotoShot Selector [TAPE/CARD]
(PV-DC252/PV-DC252-K) (l 34)
13) Card Access Lamp [ACCESS] (PV-DC252/PV-DC252-K) (l 34)
14) Card Slot (PV-DC252/PV-DC252-K) (l 34)
15) Card Slot Cover (PV-DC252/PV-DC252-K) (l 34)
16) Eyepiece Corrector Knob (l 14)
17) Viewfinder (l 14, 62)
.........................................................................................................................
Due to limitations in LCD production technology, there may be some
tiny bright or dark spots on the Viewfinder screen. However, this is not
a malfunction and does not affect the recorded picture.
.........................................................................................................................
18) Eyecup
19) Battery Holder (l 12)
20) Shoulder Strap Holders (l 13)
21) Recording Start/Stop Button (l 20, 27, 28)
22) PhotoShot Button [PHOTO SHOT] (l 21, 34, 35)
23) Zoom Lever [W/T] (l 21, 22)
24) Multi-Function Dial [PUSH] (l 15, 19, 25, 26, 29, 30)
25) Menu Button [MENU] (l 15)
26) Quick Start Lamp (l 24)
27) Quick Start Button [QUICK START] (l 24)
28) Mode Selector Switch [AUTO/MANUAL/FOCUS] (l 20, 24, 25, 26)
29) Off/On Mode Selector Switch [OFF/ON/MODE]
30) Operation Mode Lamps [CAMERA/VCR/CARD P.B.]
(PV-DC252/PV-DC252-K) (l 14, 20, 29, 36)/[CAMERA/VCR]
(PV-DC152/PV-DC152-K) (l 14, 20, 29)
31) Tripod Receptacle
Use for mounting the Palmcorder on an optional tripod.
32) Battery Eject Lever [BATT] (l 12)
1)
2)
3)
12) 13)
14)
15)
6)
SEARCH
5)
7)
FADE
9) 11)
MULTI/
P-IN-P
10)
TITLE
8)
4)
SEARCH
16)
17)
18)
19)
20)
22)
23)
28)
29)
24)
25)
27)
26)
30)
BACKLIGHT
MAGICPIX
CAMERA
STILL
31)32)
21)
9
33) Reset Button [RESET] (l 67)
34) Speaker
35) Cassette Holder
36) Cassette Eject Lever [OPEN/EJECT] (l 13)
37) Cassette Cover Close Button [PUSH CLOSE] (l 13)
38) Cassette Compartment Cover (l 13)
39) Lens Hood (l 62)
40) Lens
41) Tally Lamp (l 20)
42) White Balance Sensor (l 26, 63)
43) Remote Control Sensor (l 11)
44) Microphone (Built-in, stereo) (l 21)
45) S-Video Output Jack [S-VIDEO OUT] (l 33)
46) Audio-Video Output Jack [A/V OUT] (l 33)
Headphone Jack [PHONES]
Tethered Remote Control Jack [REMOTE]
Connecting an AV Cable or Tethered Remote Control to this Jack
activates the Palmcorders built-in speaker, but connecting a
headphone, etc. deactivates it.
When plugging the pin plug of the AV cable into the AV output terminal,
plug it in as far as it goes.
47) Microphone Jack [MIC]
Connecting with an external microphone or audio equipment. (When
this Jack is in use, the built-in microphone does not operate.) (l 21)
48) Shoulder Strap Holder/Lens Cap String Holder (l 13)
49) DV Terminal (i.LINK) [¥] (l 43)
Connect this to the digital video equipment.
i.LINK is the name of connectors in accordance with IEEE1394-1995.
¥ is a logo marked on products conforming with the i.LINK
specifications.
50) Digital Still Picture Terminal [DIGITAL STILL PICTURE]
51) USB Jack [TO PC] (PV-DC252/PV-DC252-K) (l 46)
52) Grip Belt (l 13)
51) 50) 49)
48)
DIGITAL
STILL
PICTURE
TO PC
DV
MIC
A/V OUT
A/V OUT
PHONES/REMO
PHONES/REMO
TE
S-VIDEO
S-VIDEO
OUT
OUT
47) 46) 45)
33)
34)
36)
37)
38)
39)
40)
41)
42)
43)
44)
52)
35)
10
ZOOM
INDEX INDEX
SELECT
STORE
STOP
KL
OSD
COUNTER
V
/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE
T
W
sVOL r
¥REC
MULTI/
P-IN-P
PHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAUSE
FF/
W
STILL ADV
MENU
ITEM
SET
61 5
;
ED
VAR.
SEARCH
P.B.
ZOOM
ZOOM
INDEX INDEX
SELECT
STORE
STOP
KL
OSD
COUNTER
V
/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE
T
W
sVOL r
¥REC
MULTI/
P-IN-P
PHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAUSE
FF/
W
STILL ADV
MENU
ITEM
SET
61 5
;
ED
VAR.
SEARCH
P.B.
ZOOM
ZOOM
INDEX INDEX
SELECT
STORE
STOP
KL
OSD
COUNTER
V
/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE
T
W
sVOL r
¥REC
MULTI/
P-IN-P
PHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAUSE
FF/
W
STILL ADV
MENU
ITEM
SET
61 5
;
ED
VAR.
SEARCH
P.B.
ZOOM
7)
6)
10)
8)
9)
18)
19)
17)
16)
20)
21)
22)
23)
24)
25)
3)
2)
1)
4)
11)
12)
13)
14)
15)
26)
27)
28)
29)
30)
5)
Remote Controller
Using the wireless remote controller that is supplied with the Palmcorder,
most of the Palmcorder functions can be operated from a distance.
Remote Controller Buttons
1) Date and Time Button [DATE/TIME] (l 55)
2) Indication Output Button [OSD] (l 33)
3) Counter Reset Button [RESET] (l 63)
4) Indication Shift Button [COUNTER] (l 55)
5) Multi-Picture/Picture-in-Picture Button [MULTI/P-IN-P] (l 28, 36)
6) Recording Button [REC] (l 43)
7) Audio Dubbing Button [A.DUB] (l 33)
8) Upward Direction Button [π] (for Playback Zoom Function) (l 32)
9) Left/Right Direction Button [, ] (for Playback Zoom Function)
(l 32)
10) Downward Direction Button [] (for Playback Zoom Function)
(l 32)
11) Slow Motion/Still Advance Button [E, D]
(E : reverse direction, D: normal direction) (l 30)
12) Index Search Button [:, 9]
(:: reverse direction, 9: normal direction) (l 31)
13) Selection Button [SELECT] (l 32)
14) Store Button [STORE] (l 32)
15) Off/On Button [OFF/ON] (l 32)
16) Zoom/Volume Button [ZOOM/VOL] (l 21, 22, 29, 32)
17) Variable Speed Search Button [VAR.SEARCH] (l 29)
18) Playback Zoom Button [P.B. ZOOM] (l 32)
19) Speed Selection Button [π, ] (for Variable Speed Search Function)
(l 29)
The following buttons function in the same manner as the corresponding
buttons on the Palmcorder.
20) PhotoShot Button [PHOTO SHOT] (l 21, 34)
21) Recording Start/Stop Button [START/STOP] (l 20)
22) Title Button [TITLE] (l 39)
23) Menu Button [MENU] (l 15)
24) Item Set Button [SET] (l 15)
25) Item Select Button [ITEM] (l 15)
26) Fast-forward/Cue Button [5] (l 29)
27) Play Button [1] (l 29, 36)
28) Rewind/Review Button [6] (l 29)
29) Pause Button [;] (l 30, 36)
30) Stop Button [] (l 29, 36)
ª Tethered Remote Control
This controller allows the scene to be shot in various angles, high to low and
is also convenient when the Tripod is used. When you do not use this
controller, attach the clip to the Grip Belt for convenience.
This controller allows the camera to be used more conveniently by a left-
handed user.
When using the Tethered Remote control, plug it in as far as it goes.
1
Recording Start/Stop Button [¥]
2
Zoom Lever [W/T]
3
PhotoShot Button [PHOTO SHOT]
The Grip Belt detached from the
Palmcorder can also be used wrapped
around the wrist as shown in the
illustration on the right.
1
3
2
11
1
3
2
1
ZOOM
INDEX INDEX
SELECT
STORE
STOP
KL
OSD
COUNTER
V
/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE
T
W
sVOL r
¥REC
MULTI/
P-IN-P
PHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAUSE
FF/
W
STILL ADV
MENU
ITEM
SET
61 5
;
ED
VAR.
SEARCH
P.B.
ZOOM
1
15˚
15˚
15˚
15˚
ª Inserting the Button-type Battery
Before using the remote controller, insert the supplied button-type battery.
1
While pressing the Stopper
1
, pull out the Battery Holder.
2
Insert the button-type battery with the imprint (
i
) facing
upward.
3
Insert the Battery Holder into the Remote Controller.
When the button-type battery becomes weak, replace it with a new CR2025
battery. (A battery is normally expected to last about one year. However, it
depends on operation frequency.)
Be sure to match the poles properly when inserting the battery.
................................................................................................................................
................................................................................................................................................................................................................................................................
.....................................................................................................................................................................
..........................................................................
.....................................
Warning
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
equipment manufacturer. Discard used batteries according to
manufacturer’s instructions.
Risk of fire, explosion and burns. Do not recharge, disassemble, heat
above 212° F (100° C) or incinerate. Keep the Button-Type battery out of
the reach of children. Never put Button-Type battery in mouth. If
swallowed, call your doctor.
................................................................................................................................
................................................................................................................................................................................................................................................................
.....................................................................................................................................................................
..........................................................................
.....................................
Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only.
Use of another battery may present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep away from children.
Do not recharge, disassemble or dispose of in fire.
~~~~~~~~~~~~~~~~~~~~~~~~~
ª Using the Remote Controller
1
Direct the Remote Controller at the Remote Control Sensor
on the Palmcorder and press the desired button.
Distance from the Palmcorder: Within approximately 15 feet (5 meters)
Angle: Approximately 15 degrees in the vertical and horizontal
directions from the central axis
The above operating ranges are for indoor use. Outdoors, or under strong
light, the equipment may not operate properly even within the above
ranges.
Within 3 feet (1 meter) range, you can also use the Remote Controller on
the side (the LCD Monitor side) of the Palmcorder.
Selecting Remote Controller Modes
When two Palmcorders are used simultaneously, they can be operated
individually by selecting different Remote Controller Modes.
If the Remote Controller Mode on the Palmcorder and Remote Controller do
not match, [REMOTE] is displayed.
Setting on the Palmcorder:
Set [REMOTE] on the [OTHER FUNCTIONS] Sub-Menu to the desired
Remote Controller Mode.
Setting on the Remote Controller:
[VCR1]: Press the [D] Button and [] Button simultaneously.
1
[VCR2]: Press the [E] Button and [] Button simultaneously.
2
When the battery in the Remote Controller is replaced, the Mode is
automatically reset to [VCR1] Mode.
12
CGR
-
CGR
-
CGP
-
CGR
-
3
2
1
1
CGR-D08A/1B
A
B
A
B
A
A
B
B
1 h.
2 h.
3 h 15 min.
2 h 10 min.
(1 h 35 min.)
4 h 20 min.
(3 h 10 min.)
7 h 40 min.
(5 h 35 min.)
5 h 20 min.
14 h 10 min.
(10 h 25 min.)
CGR-D16A/1B
CGP-D28A/1B
CGR-D53A/1K
Power Supply
ª Using the AC Adaptor
1
Insert the battery-shaped connector of the DC Cable into the
Battery Holder on the Palmcorder.
2
Connect the DC Cable to the [DC OUT] Jack on the AC
Adaptor.
3
Connect the AC Adaptor and AC Cable.
The AC Cables outlet plug cannot be pushed fully into the AC Adaptor
Jack. A gap will remain as shown
1
.
Before disconnecting the power supply, set the [OFF/ON/MODE] Switch on
the Palmcorder to [OFF].
Battery cannot be charged if DC Cable is connected to AC Adapter.
ª Using the Battery
Before use, fully charge the battery.
1
Attach the Battery to AC Adaptor and charge it.
Since the Battery will not be charged when the DC Cable is connected
to the AC Adaptor, disconnect it.
The [POWER] Lamp and [CHARGE] Lamp lights up, and charging
starts.
When the [CHARGE] Lamp goes off, charging is completed.
2
Attach the charged Battery to the Palmcorder.
Disconnecting the Power Source
Set the [OFF/ON/MODE] Switch
1
to [OFF], and the [BATT] Lever to the
right
2
, and then slide the Battery to remove it.
When attaching or removing battery, set [OFF/ON/MODE] Switch to
[OFF] and make sure the Operation Mode Lamp is not lit.
For other notes, see page 56.
~~~~~~~~~~~~~~~~~~~~~~~~
Charging Time and Available Recording Time
A
Charging Time
B Maximum Continuous Recording Time
1 h 20 min." indicates 1 hour and 20 minutes.
Battery CGR-D08R is supplied.
The hours shown in the table are approximate hours. The numeric
characters in parentheses indicate the recording time when the LCD
monitor is used. In actual use, the available recording time may be shorter
in some cases.
The hours shown in the table are for continuous recording at a temperature
of 68xF (20xC) and humidity of 60%. If the Battery is charged at a higher or
lower temperature, the charging time may longer.
1
2
O
F
F
O
N
M
O
D
E
BAT T
13
R E C
SAVE
1
2
1
4
OPEN/
EJECT
1
3
CLOSE
PUSH
1
2
3
1
Lens Cap and Grip Belt
ª Attach the Lens Cap
To protect the Lens surface, attach the Lens Cap.
1
Pass the end of the Lens Cap String through the Lens Cap
String holder.
2
Pass the other end of the String through the loop made by
the String itself and pull it toward the direction indicated by
an arrow.
3
Fit the lens cap onto the lens cap string.
The removed Lens Cap can be hooked onto the Grip Belt
1
. (When you
are not recording, be sure to keep the Lens Cap attached to the Lens for
protection.)
ª Adjust the Grip Belt
Adjust the length of the Grip Belt to the size of your hand.
1
11
1
Detach the tip of the Grip Belt and adjust the length of it.
2
22
2
Reattach the Grip Belt.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Attaching the Shoulder Strap
We recommend that you attach the Shoulder Strap before going outdoors to
record so as to avoid dropping the Palmcorder.
1
Pass the tip of the Shoulder Strap through the Shoulder
Strap Holder on the Palmcorder and pull the Shoulder Strap.
2
Fold the tip of the Shoulder Strap, pass it through the
Shoulder Strap Length Adjuster, and pull it.
Pull it out more than 1 inch (2 cm)
1
from the Shoulder Strap Length
Adjuster so that it cannot slip off.
~~~~~~~~~~~~~~~~~~~~~~~~~
Inserting a Cassette
When power is supplied to the Palmcorder, the cassette can be taken out
without turning the Palmcorder on.
1
Slide the [OPEN/EJECT] Lever toward the front and pull
down to open the Cassette Compartment.
2
Insert a Cassette.
3
Close the Cassette Compartment by pressing the
[PUSH CLOSE] Button.
4
Close the Cassette Compartment Cover.
For other notes, see page 56.
ª Accidental Erasure Prevention
Opening the accidental erasure prevention slider
1
on the cassette (by
sliding it in the [SAVE] arrow direction) prevents recording. To enable
recording, close the accidental erasure protection slider (by sliding it in the
[REC] arrow direction.)
1
2
1
14
23
180x 90x
12:30:45AM
OCT 15 2002
12:30:45AM
OCT 15 2002
12:30:45AM
OCT 15 2002
12:30:45AM
OCT 15 2002
LCD/EVF SET
PUSH MENU TO RETURN
LCD BRIGHTNESS
LOW||||----HIGH
LCD COLOR LEVEL
LOW||||----HIGH
EVF BRIGHTNESS
LOW||||----HIGH
1
OPEN
2
1
Turning on/off the Palmcorder and Selecting
Modes
Turn on the power first and then select Modes.
ª How to Turn on the Power
1
Set the [OFF/ON/MODE] Switch to [ON] while pressing the
center Button
1
.
The [CAMERA] Lamp lights up.
ª How to Switch Modes
2
Rotate the [OFF/ON/MODE] Switch.
With each slide of the Switch, the Mode switches in the order of Camera
Mode, VCR Mode, and Card Playback Mode.
(PV-DC252/PV-DC252-K)
The appropriate Mode Lamp lights up.
ª How to Turn off the Power
3
Set the [OFF/ON/MODE] Switch to [OFF] while pressing the
center Button
1
.
~~~~~~~~~~~~~~~~~~~~~~~~
Using the Viewfinder
Before using the Viewfinder, adjust the field of view so that the displays inside
the Viewfinder become clear and easy to read.
1
Pull the Viewfinder.
2
Adjust by turning the Eyepiece Corrector Knob
1
.
Using the LCD Monitor
With the LCD Monitor open, you can also record the picture while watching it.
1
11
1
Set the [OFF/ON/MODE] Switch to [ON].
2
22
2
Bring out the [OPEN] Tab about 90x in the direction of the
arrow to open the LCD Monitor.
The Viewfinder goes off.
3
33
3
Adjust the LCD Monitor angle according to the desired
recording angle.
The LCD Monitor can rotate a maximum of 180x
2
from the vertical
position to the upward direction and a maximum of 90x
3
to the
downward direction. Forcefully rotating the LCD monitor beyond these
ranges will damage the Palmcorder.
Closing the LCD monitor
Push the LCD Monitor until it is securely locked.
ª Adjusting Brightness and Color Level
When [LCD/EVF SET] on the [DISPLAY SETUP] Sub-menu is set to [YES],
the following items are displayed:
LCD Brightness [LCD BRIGHTNESS]
Adjusts the brightness of the image on the LCD screen.
LCD Color Level [LCD COLOR LEVEL]
Adjusts the color saturation of the image on the LCD screen.
Brightness of the Viewfinder [EVF BRIGHTNESS]
Adjust the brightness of the image in the Viewfinder.
1
Press the [PUSH] Dial and select the item you want to adjust.
2
Rotate the [PUSH] Dial and increase or decrease the number
of the vertical bars on the Bar Indication.
The Bar Indication has 8 steps. A larger number of vertical bars
indicates stronger brightness or color saturation.
Increasing the Brightness of the Entire LCD Monitor
Set the [LCD MODE] on the [DISPLAY SETUP] Sub-Menu to [BRIGHT].
These adjustments do not affect the recorded images.
For other notes, see page 62.
O
F
F
O
N
M
O
D
E
1, 2
3
1
CAMERA
VCR
CARD
P.B.
15
Using the Menu Screen
To facilitate the selection of a desired function or setting, this Palmcorder
displays various function settings on menus.
1
Press the [MENU] Button.
The Menu corresponding to the Mode selected by using the [OFF/ON/
MODE] Switch
1
is displayed.
When the [CAMERA] Lamp is on, the Camera Function Menu is
displayed.
2
When the [VCR] Lamp is on, the VCR Function Menu is displayed.
3
When the [CARD P.B.] Lamp is on, the Card Function Menu is
displayed.
4
(PV-DC252/PV-DC252-K)
2
Rotate the [PUSH] Dial to select a desired Sub-Menu.
Rotate the [PUSH] dial to display the items highlighted.
3
Press the [PUSH] Dial to display the selected Sub-Menu.
4
Rotate the [PUSH] Dial to select the item to be set.
5
Press the [PUSH] Dial to set the selected item to a desired
Mode.
With each press of the [PUSH] Dial, the cursor [1] brings up a
subsequent Mode. Menu items that cannot be used in combination with
the selected menu items are displayed in dark blue.
While a Menu is displayed, you cannot begin to record or play back. Menus
can be displayed during playback but not during recording.
The above operations can be carried out using the Remote Controller.
(l 10)
To display the Menu, press the [MENU] Button
5
on the Remote
Controller.
To select items on the Menu, press the [ITEM] Button
6
on the
Remote Controller.
To set the mode for the selected items, press the [SET] Button
7
on the Remote Controller.
To Exit the Menu Screen
Press the [MENU] Button again.
About the Menu Mode Setting
The setting selected on the Menu will be retained even when the Palmcorder
is turned off. However, if the Battery or AC Adaptor is disconnected before
Turning the Palmcorder off, the selected setting may not be retained.
(But, the setup of [EFFECT2] (l 27) is not retained.)
Menu operation flow is shown in this text by >>.
ª File Selection in the Card Playback Mode
(PV-DC252/PV-DC252-K)
A File Selection Operation may be necessary during Menu Operations. In this
case, carry out the following procedure.
1
11
1
Turn the [PUSH] Dial and select a file.
The selected file is marked by a frame
8
.
2
22
2
Press the [PUSH] Dial to confirm the selection of the file.
After the above File Selection Procedure, carry out the various Menu
Operations. (The above procedure will not be repeated in the following
instructions.)
PICTURE
No.25 100-0012
8
2
CAMERA FUNCTIONS
PUSH MENU TO EXIT
1.
CAMERA SETUP
2.
DIGITAL EFFECT
3.
CARD SETUP
5.
RECORDING SETUP
6.
DISPLAY SETUP
7.
OTHER FUNCTIONS
PUSH MENU TO EXIT
2.
DIGITAL EFFECT
3.
CARD SETUP
4.
RECORDING SETUP
5.
DISPLAY SETUP
6.
OTHER FUNCTIONS
1.
PLAYBACK FUNCTIONS
CARD FUNCTIONS
PUSH MENU TO EXIT
1.
DELETE CARD FILE
2.
CARD EDITING
3.
DISPLAY SETUP
4.
OTHER FUNCTIONS
VCR FUNCTIONS
3
4
4.
MULTI-PICTURES
1
M
E
N
U
1
2, 3, 4, 5
O
F
F
O
N
M
O
D
E
CAMERA
VCR
CARD
P.B.
2
3
4
ZOOM
INDEX INDEX
SELECT
STORE
STOP
KL
OSD
COUNTER
V
/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE
T
W
sVOL r
¥REC
MULTI/
P-IN-P
PHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAUSE
FF/
W
STILL ADV
MENU
ITEM
SET
61 5
;
ED
VAR.
SEARCH
P. B.
ZOOM
5
7
6
16
PROG.AE OFF
5 7
4 º
RETURN ---- YES
PROGRESSIVE AUTO ON OFF
EIS
D.ZOOM
OFF ON
OFF 25 700
CINEMA OFF ON
RETURN
CAMERA SETUP
PUSH MENU TO EXIT
1)
2)
3)
4)
5)
6)
7)
8)
AUDIO-REC 12bit
RETURN ---- YES
SP LP
2HOUR DAY
WIND-CUT OFF ON
ZOOM MIC OFF ON
RECORDING SETUP
PRESS MENU TO EXIT
DATE/TIME
C.DISPLAY LINEAR MEMORY
T.CODE
RETURN ---- YES
OFF D/T DATE
C.RESET ---- YES
DISPLAY ALL PARTIAL OFF
LCD/EVF SET ---- YES
LCD MODE NORMAL BRIGHT
DISPLAY SETUP
PUSH MENU TO EXIT
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
25)
26)
9)
10)
11)
12)
13)
14)
SCAN MODE
SPEED FAST NORMAL SLOW
RETURN ---- YES
STROBE MANUAL
SWING OFF ON
P-IN-P 1 2 3 4
MULTI-PICTURES
PUSH MENU TO EXIT
REMOTE
TALLY LED OFF ON
RETURN ---- YES
VCR1 VCR2 OFF
BEEP OFF ON
SHUTTER OFF ON
SELF-REC NORMAL MIRROR
CLOCK-SET
---- YES
OTHER FUNCTIONS
PUSH MENU TO EXIT
27)
28)
29)
30)
31)
WIPE MIX STROBE
GAIN-UP TRAIL
MOSAIC MIRROR
EFFECT1
MONO SOLARI
OFF MULTI P-IN-P
EFFECT2 OFF NEGA SEPIA
RETURN ---- YES
DIGITAL EFFECT
PUSH MENU TO EXIT
CARD SETUP
PUSH MENU TO EXIT
RETURN ---- YES
---- YES
PICTURE QUALITY
FINE NORMAL ECONOMY
CREATE TITLE
REC-SPEED
INDEX
RECORDING SETUP
PUSH
MENU TO EXIT
16bit
List of Menus
The illustrations of the Menus are for explanation purposes only, and they are
different from the actual Menus.
Camera Mode Main-Menu [CAMERA FUNCTIONS]
[CAMERA SETUP] Sub-Menu
1) Auto Exposure Mode [PROG.AE] (l 24)
2) Progressive PhotoShot Mode [PROGRESSIVE] (l 21)
3) Digital Effect Image Stabilizer [EIS] (l 22)
4) Digital Zoom [D.ZOOM] (l 22)
5) Cinema-like Format Recording [CINEMA] (l 23)
6) Returning to the Main-Menu [RETURN]
[DIGITAL EFFECT] Sub-Menu
7) Digital Effects 1 [EFFECT1] (l 27)
8) Digital Effects 2 [EFFECT2] (l 27)
[CARD SETUP] Sub-Menu (PV-DC252/PV-DC252-K)
9) Picture Quality [PICTURE QUALITY] (l 35)
10) Title Creation [CREATE TITLE] (l 39)
[MULTI-PICTURES] Sub-Menu
11) Multi-Picture Mode [SCAN MODE] (l 28)
12) Strobe Multi-Picture Speed [SPEED] (l 28)
13) Swing Mode [SWING] (l 28)
14) Position of Small Picture inside Normal Picture [P-IN-P] (l 28)
[RECORDING SETUP] Sub-Menu
15) Recording Speed Mode [REC-SPEED] (l 19)
16) Audio Recording Mode [AUDIO-REC] (l 19, 33)
17) Index Mode [INDEX] (l 31)
18) Wind Noise Reduction [WIND-CUT] (l 24)
If this function is set to [ON], the sound of wind hitting the microphone
can be reduced for recording.
19) Zoom Microphone [ZOOM MIC] (l 21)
[DISPLAY SETUP] Sub-Menu
20) Date and Time Indication [DATE/TIME] (l 55)
21) Counter Display Mode [C.DISPLAY] (l 55)
22) Counter Reset [C.RESET] (l 63)
Set the counter value to zero. However, it cannot reset the Time Code.
23) Display Mode [DISPLAY] (l 55)
24) LCD Brightness [LCD MODE] (l 14)
25) LCD and Viewfinder Adjustment [LCD/EVF SET] (l 14)
[OTHER FUNCTIONS] Sub-Menu
26) Remote Controller Mode [REMOTE] (l 11)
27) Recording Lamp [TALLY LED] (l 20)
28) Beep Sound [BEEP] (l 56)
29) Shutter Effect [SHUTTER] (l 21)
30) Date and Time Setting [CLOCK-SET] (l 19)
31) Self-Recording [SELF-REC] (l 20)
17
DIGITAL EFFECT
PUSH MENU TO EXIT
RETURN ---- YES
EFFECT OFF ON
EFFECT SELECT
OFF WIPE MIX
STROBE NEGA SEPIA
MONO TRAIL SOLARI
MOSAIC MIRROR
BLANK SEARCH ---- YES
RETURN ---- YES
RECORD TO CARD ---- YES
PLAYBACK FUNCTIONS
PUSH MENU TO EXIT
INDEX PHOTO SCENE
AUDIO OUT STEREO L R
AUDIO ST1 ST2 MIX
2)
1)
3)
4)
6)
7)
8)
9)
OTHER FUNCTIONS
PUSH MENU TO EXIT
REMOTE VCR1 VCR2 OFF
RETURN ---- YES
CLOCK-SET ---- YES
RECORDING SETUP
PUSH MENU TO EXIT
REC-SPEED SP LP
AUDIO-REC 12bit
16bit
RETURN ---- YES
DISPLAY SETUP
PUSH MENU TO EXIT
DATE/TIME OFF D/T DATE
C.DISPLAY LINEAR MEMORY
T.CODE
C.RESET ---- YES
DISPLAY ALL PARTIAL OFF
LCD MODE NORMAL BRIGHT
LCD/EVF SET ---- YES
RETURN ---- YES
11)
12)
10)
5)
CARD SETUP
PUSH MENU TO EXIT
PICTURE QUALITY
FINE NORMAL ECONOMY
RETURN ---- YES
---- YES
CREATE TITLE
VCR Mode Main-Menu [VCR FUNCTIONS]
[PLAYBACK FUNCTIONS] Sub-Menu
1) Blank Search [BLANK SEARCH] (l 30)
2) Recording to Card [RECORD TO CARD] (PV-DC252/PV-DC252-K)
(l 35)
3) Index Search Mode [INDEX] (l 31)
4) Audio Selector [AUDIO] (l 33)
5) Audio Output Mode [AUDIO OUT] (l 58)
6) Returning to the Main-Menu [RETURN]
[DIGITAL EFFECT] Sub-Menu
7) Digital Effect On/Off [EFFECT] (l 32)
8) Digital Effect Selection [EFFECT SELECT] (l 32)
[CARD SETUP] Sub-Menu (PV-DC252/PV-DC252-K)
9) Picture Quality [PICTURE QUALITY] (l 35)
10) Title Creation [CREATE TITLE] (l 39)
[RECORDING SETUP] Sub-Menu
11) Recording Speed Mode [REC-SPEED] (l 19)
12) Audio Recording Mode [AUDIO-REC] (l 19, 33)
[DISPLAY SETUP] Sub-Menu
Same as described on page 16.
[OTHER FUNCTIONS] Sub-Menu
Same as described on page 16.
18
Card Playback Mode Main-Menu [CARD FUNCTIONS]
(PV-DC252/PV-DC252-K)
[DELETE CARD
FILE] Sub-Menu
1) Selecting and deleting a File [DELETE FILE BY SELECTION] (l 40)
2) Deleting All Files [DELETE ALL FILES] (l 40)
3) Selecting and Deleting a Title [DELETE TITLE BY SELECTION] (l 40)
[CARD EDITING] Sub-Menu
4) Recording to Cassette [RECORD TO TAPE] (l 37)
5) Searching a File [FILE SEARCH] (l 36)
6) Setting the Lock [FILE LOCK] (l 40)
7) Setting a Slide Show [SLIDE SHOW] (l 38)
8) Setting DPOF [DPOF SETTING] (l 41)
9) Formatting a Card [CARD FORMAT] (l 41)
[DISPLAY SETUP] Sub-Menu
Same as described on page 16.
[OTHER FUNCTIONS] Sub-Menu
Same as described on page 16.
Short-Cut Menus of the Card Playback Mode
(PV-DC252/PV-DC252-K)
A
If you use the Short-Cut Menu, the Card Playback Mode Menu can be called
up quickly. Press the [PUSH] Dial to display the Short-Cut Menu, and turn the
[PUSH] Dial to select the desired Menu.
10) [FILE SEARCH]:
The [FILE SEARCH] Menu for finding files by number appears. (l 36)
11) [DELETE FILE]:
The [DELETE FILE] Menu for deleting the file being displayed appears.
(l 40) Use this Menu after the file to be erased appears.
12) [FILE LOCK]:
The [FILE LOCK] Menu to prevent the accidental erasure of files (Lock
Setting) being displayed appears. (l 40) Use this Menu after the file to
be locked appears.
13) [DPOF SETTING]:
The [DPOF SETTING] Menu for performing the DPOF settings for the
displayed picture appears. (l 41) Use this Menu after the picture whose
DPOF settings are to be performed has appeared.
14) [EXIT]:
For terminating the Short-Cut Menu.
RETURN ---- YES
PUSH MENU TO EXIT
RETURN ---- YES
DISPLAY SETUP
PUSH MENU TO EXIT
DATE/TIME OFF D/T DATE
C.DISPLAY LINEAR MEMORY
T.CODE
C.RESET ---- YES
DISPLAY ALL PARTIAL OFF
LCD MODE NORMAL BRIGHT
LCD/EVF SET ---- YES
OTHER FUNCTIONS
PUSH MENU TO EXIT
REMOTE VCR1 VCR2 OFF
CLOCK-SET ---- YES
DPOF SETTING ---- YES
CARD EDITING
PUSH MENU TO EXIT
RECORD TO TAPE ---- YES
FILE SEARCH ---- YES
RETURN ---- YES
RETURN ---- YES
FILE LOCK ---- YES
SLIDE SHOW ---- YES
CARD FORMAT ---- YES
DELETE CARD FILE
1.
DELETE FILE
BY SELECTION
2.
DELETE ALL FILES
3.
DELETE TITLE
BY SELECTION
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
FILE SEARCH
DELETE FILE
FILE LOCK
DPOF SETTING
EXIT
A
19
CLOCK-SET
PUSH MENU TO RETURN
YEAR :2002
MONTH :JAN
DAY :20
HOUR : 8PM
MINUTE:46
M
E
N
U
1, 3
1, 2
CAMERA FUNCTIONS
PUSH MENU TO EXIT
1.
CAMERA SETUP
2.
DIGITAL EFFECT
3.
CARD SETUP
4.
MULTI-PICTURES
5.
RECORDING SETUP
6.
DISPLAY SETUP
7.
OTHER FUNCTIONS
1
2
AUDIO-REC
REC-SPEED
AUDIO-REC 12bit
RETURN ---- YES
SP LP
INDEX 2HOUR
WIND-CUT OFF
RECORDING SETUP
PUSH
MENU TO EXIT
ZOOM MIC
ON
REC-SPEED
12bit
RETURN ---- YES
SP
INDEX 2HOUR
WIND-CUT OFF
RECORDING SETUP
PUSH
MENU TO EXIT
ZOOM MIC
ON
16bit
Setting Date and Time
1
Press the [MENU] Button and rotate the [PUSH] Dial to select
[OTHER FUNCTIONS] >> [CLOCK-SET] >> [YES].
2
Rotate and press the [PUSH] Dial to select [YEAR]/[MONTH]/
[DAY]/[HOUR]/[MINUTE] and set it to a desired value.
Year will cycle in the order shown below.
2000 ) 2001 ) ... ) 2089 ) 2000 ) ...
3
Press the [MENU] Button to finish setting the date and time.
The clock operation starts from [00] seconds.
The menu will disappear when the [MENU] button is pressed again.
It is possible that the built-in clock in the Palmcorder may become
inaccurate. Please check the time before recording. If the [0] Indication is
flashing, charge the built-in lithium battery and reset the date and time.
~~~~~~~~~~~~~~~~~~~~~~~~~
Internal Lithium Battery Recharge
The internal lithium battery sustains the operation of the clock. When the [0]
Indication
1
is lit, the internal lithium battery is near discharge.
1
11
1
Connect the AC Adaptor to the Palmcorder with the power
turned off and then connect to the AC Jack.
After charging for 4 hours, the built-in lithium battery can power the
clock for approximately 3 months.
~~~~~~~~~~~~~~~~~~~~~~~~~
LP Mode
A desired recording speed can be selected with [REC-SPEED] on the
[RECORDING SETUP] Sub-Menu.
1
If LP Mode is selected, the recording time becomes 1.5 times longer
than that of SP Mode.
Although the image quality does not decrease with the LP Mode recording,
mosaic-like noise patterns may appear on a playback image, or some normal
functions may be restricted.
The contents that are recorded in LP Mode are not completely compatible
with other equipment.
Audio Dubbing is not possible with LP Mode. (l 33)
~~~~~~~~~~~~~~~~~~~~~~~~~
Audio Recording Mode
The sound quality of the recorded sound can be selected with [AUDIO-REC]
on the [RECORDING SETUP] Sub-Menu.
2
High sound-quality recording is possible with 16bit 48kHz 2 track Mode.
With the 12bit 32kHz 4 track Mode, the original sound can be recorded on
2 tracks in stereo, while the other 2 tracks can be used for re-recording.
1
20
3
2
RECORD
REC
4
PAUSE
PAUSE
1
CAMERA
VCR
CARD
P.B.
1
3,
4
AUTO MANU
MANU
AL FOCUS
FOCUS
5
O
F
F
O
N
M
O
D
E
2
TAPE
CARD
CARD
CAMERA Mode
Recording
1
Set the [OFF/ON/MODE] Switch to [ON].
The [CAMERA] Lamp lights up.
1
2
Slide the [TAPE/CARD] Selector towards [TAPE].
(PV-DC252/PV-DC252-K)
3
Press the Recording Start/Stop Button.
Recording starts.
After the [RECORD] indicator is displayed, it changes to [REC].
2
The Tally Lamp (LED Lamp)
3
lights up during recording and alerts
those being recorded that recording is in progress. The Tally Lamp
does not light up if the [TALLY LED] on the [OTHER FUNCTIONS]
Sub-menu is set to [OFF].
4
Press the Recording Start/Stop Button again to pause the
recording.
[PAUSE] Indication is displayed.
4
If the Recording Pause Mode continues for more than 5 minutes, the power
is turned off automatically for tape protection and power conservation. To
resume recording from this condition, turn on the power again.
When recording while the Mode Selector Switch is set to [AUTO]
5
, the
Palmcorder automatically adjusts the focus and white balance. (In some
cases, they cannot be adjusted automatically and need to be adjusted
manually.) (l 25, 26)
ª To Check the Recording
By pressing the [S] Button
6
in the Recording Pause Mode, you can play
back the last few seconds of the recorded scene.
[CHK]
is displayed. After checking, the Palmcorder resumes the Recording
Pause Mode.
ª To View the recorded scene while the Recording is
paused
(Camera Search)
The recorded scene can be viewed by holding down the [SEARCHj] Button
6
or [SEARCHi] Button
7
in the Recording Pause Mode.
The Camera Search function is useful for finding the starting point of a new
scene to create a smooth transition from one scene to another.
When the [SEARCHj] Button is pressed, images are played back in the
reverse direction.
When the [SEARCHi] Button is pressed, images are played back in the
forward direction.
ª Self-Recording
By opening the LCD Monitor and turning it so that it faces forward (to the lens
side), you can let the subject in front of the Palmcorder monitor the shot while
shooting is in progress.
When the LCD Monitor is opened, the Viewfinder is disabled automatically.
However, when the LCD Monitor is rotated forward, the image is also
shown in the Viewfinder.
If you prefer to have the image on the LCD Monitor to look like an image in
a mirror, set [SELF-REC] on the [OTHER FUNCTIONS] Sub-Menu to
[MIRROR]. (Mirror Mode)
Images are recorded normally and no left and right reversal occurs.
If [MIRROR] is selected, only recording Indication [¥], recording pause
Indication [¥;], Card PhotoShot Indication [ ] (PV-DC252/
PV-DC252-K) and Remaining Battery Power Indication [x] are
displayed
8
.
If a general Warning/Alarm Indication [°] appears, return the LCD Monitor
to the original position in order to check the specific content of the Warning/
Alarm Indication.
ª To Finish the Recording
Set the [OFF/ON/MODE] Switch to [OFF].
For other notes, see page 56.
8
SEARCH
7
SEARCH
6
°
x
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148

Panasonic PVDC152 Le manuel du propriétaire

Catégorie
Caméscopes
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues