Air King AK150LS Manuel utilisateur

Marque: Air King

Modèle: AK150LS

Catégorie: Barbecues

Taper: Manuel utilisateur

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT

YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions

should always be followed to reduce the risk of fire,

electric shock and injury to person, including the following:

1. Read all instructions before installing or using exhaust fan.

2. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer.

3. Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the

service panel.

4. Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-related construction.

5. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent back drafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA)

and the American Society for Heating, Refrigeration, and Air

Conditioning Engineers (ASHRAE), and the local code authorities.

CAUTION: FOR GENERAL VENTILATING USE ONLY. DO

NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS

AND VAPORS.

Models: AK150LS,

AK200LS, AK300LS

www.airkinglimited.com

210572051 Rev. A 8-05

Exhaust Fan

SAVE THESE INSTRUCTIONS

6. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

7. Ducted fans must always be vented to the outdoors.

8. This unit must be grounded.

9. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off

power unit.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL

DEVICE.

10. Acceptable for use over a bathtub or shower when installed

in a GFCI protected branch circuit.

11. NEVER place a switch where it can be reached from a tub or

shower.

WARNING: DO NOT USE IN KITCHENS

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

1 of 12

1c. Installation on 24" Centers Joists or Larger than 2x6 Joists on 16"

Centers: Install two - 2x4 headers (not included) between the joists

(Figure 4). Install the mounting brackets through the top set of slots

on the fan housing and secure in place with the four included #10-

32 nuts as shown. Position the fan housing between the headers

and secure the mounting brackets with screws or nails (not included)

to the header. Adjust the height of the housing so that it is flush

with the finished ceiling by loosening the mounting bracket nuts

and sliding the housing up or down on the bracket. Fully tighten all

four nuts to secure the housing in place (Figure 5).

SECTION 3

Ducting

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND

NATIONAL BUILDING CODES.

1. Connect the ducting to the fan’s duct collar (Figure 6). Secure in

place using tape or screw clamp. Always duct the fan to the outside

through a wall or roof cap.

INSTALLATION INSTRUCTIONS

CAUTION:

MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and confirm that all pieces are present.

In addition to the exhaust fan you should have:

1 - Grill

1 - Damper Assembly (attached)

2 - Mounting Brackets

1 - Mounting Flange

4 - 10-32 Nuts

1 - Instruction/Safety Sheet

2. Choose the location for your fan. To ensure the best air and sound

performance, it is recommended that the length of ducting and the

number of elbows be kept to a minimum, and that insulated hard

ducting be used. Larger duct sizes will

reduce noise and airflow restrictions.

This fan will require at least 10" of

clearance in the ceiling or wall, and will

mount through drywall up to 3/4" thick.

3. Select the most convenient electrical

knockout and remove using a straight-

blade screw driver (Figure 1).

SECTION 2

Mounting the Housing

1a. Installation on 2x4 Joists on 16" Centers: Install the mounting

brackets through the second set of slots on the fan housing and

secure in place with the four included #10-32 nuts as shown. Center

the fan housing between the joists and secure the mounting

brackets with screws or nails (not included) to the joist. Adjust the

height of the housing so that it is flush with the finished ceiling by

loosening the mounting bracket nuts and sliding the housing up or

down on the bracket. Full tighten all four nuts to secure the housing

in place (Figure 2).

1b. Installation on 2x6 Joists on 16" Centers: Install the mounting

brackets through the second set of slots on the fan housing and

secure in place with the four included #10-32 nuts as shown. Center

the fan housing between the joists and secure the mounting

brackets with screws or nails (not included) to the joist. Adjust the

height of the housing so that it is flush with the finished ceiling by

loosening the mounting bracket nuts and sliding the housing up or

down on the bracket. Fully tighten all four nuts to secure the

housing in place (Figure 3).

Figure 1

www.airkinglimited.com

210572051 Rev. A 8-05 2 of 12

Figure 3

Joist

Housing

Bracket

Nut

Figure 2

Joist

Housing

Bracket

Nut

Figure 5

Header

Housing

Bracket

Nut

Figure 4

Joist

2 x 4 Header

Joist

2 x 4 Header

Ceiling

SECTION 4

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE

IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL

ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF

INSTALLING ELECTRICAL WIRING, SECURE THE SERVICES OF A

QUALIFIED ELECTRICIAN.

NOTE: This unit includes a side access panel for wiring that does not

require the removal of the fan’s blower assembly. If you choose to wire

the unit from the inside, you will need to remove the blower assembly

and internal wiring compartment. Both methods are equally effective.

1a. External Wire Compartment: Remove the wire compartment cover

screw and place cover in a secure place (Figure 7).

1b. Internal Wire Compartment: Using a 7/16" socket, remove the two

hex nuts holding the blower assembly in place. Lift up on the

assembly and slide it out of the tabs on the housing (Figure 8).

Remove the wire compartment cover screw and place the cover

in a secure place (Figure 9).

NOTE: If the fan motor plug is connected to the fan housing receptacle,

unplug so the blower assembly can be completely removed.

2. Run wiring from an approved wall switch carrying the appropriate

rating. One neutral (white), one ground (green or bare copper), and

one hot (black lead connected to the switch). Secure the electrical

wires to the housing with an approved electrical connector. Make

sure you leave enough wiring in the box to make the connection

to the fan’s receptacle.

3. From where you have chosen to access the fan’s junction box,

connect the white wire from the house to the white wire from the

fan’s receptacle. Connect the black wire from the wall switch to

the black wire from the fan’s receptacle. Connect the ground wire

from the house to the green wire from the fan housing (Figure 10).

Use approved methods for all connections.

NOTE: The fan’s receptacle wires might need to be pulled outside

compartment for connection. Only pull the three loose wires outside of

compartment. Additional wires will be present.

4. Carefully tuck wire back inside wire compartment and replace wire

compartment cover securing with the screw that was removed earlier.

SECTION 5

Completing the Installation

1. If the fan’s blower assembly was removed during the wiring

process, reinstall the blower by reversing the directions in Section

4 (Wiring)

, Step 1b

2. Plug the fan’s quick connect motor cord into the receptacle. This

cord will only fit one way into the receptacle (Figure 11).

3. Install the ceiling mounting flange to cover any gaps which exist

between the housing and the finished ceiling. Line up the slots in

the ceiling mounting flange with the screws on the inside of the

www.airkinglimited.com

3 of 12

Figure 7

Screw

Wire

Compartment

Cover

Figure 8

Plug

Hex Nuts

Tabs

Ground

Hot (Black)

White

Supply from

house

Figure 11

Ducting

Duct

Collar

Figure 6

Screw

Wire Compartment

Cover

Figure 9

Figure 10

210572051 Rev. A 8-05

housing and press flange in place so it is tight against the ceiling.

Tighten both screws inside the housing. Install drywall screws (not

included) through the holes in the flange and into the ceiling. Install

as many drywall screws needed to ensure the flange fits tightly

against the ceiling (Figure 12).

4. Install the grill by squeezing the two ends of the springs together

and installing them up into the slots on the fan’s housing. Push the

grill up into position (Figure 13).

5. Restore power and test your installation.

www.airkinglimited.com

210572051 Rev. A 8-05 4 of 12

Figure 13

Figure 12

Drywall Screw

Ceiling

Mounting

Flange

Slots

Screws

SECTION 6

Use and Care

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE SERVICING THE UNIT.

1. Cleaning the Grill: Remove grill and use a mild detergent, such as

dishwashing liquid, and dry with a soft cloth. NEVER USE ANY

ABRASIVE PADS OR SCOURING POWDERS. Completely dry grill

before reinstalling. Refer to instructions in Section 5

Finishing the

Installation

, to reinstall grill.

2. Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently

vacuum the fan. NEVER IMMERSE ELECTRICAL PARTS IN WATER.

Troubleshooting Guide

Trouble Probable Cause Suggested Remedy

1. Fan does not operate when the switch is on. 1a. A fuse may be blown or a circuit tripped. 1a. Replace fuse or reset circuit breaker.

1b. Connector plug from motor is not plugged in. 1b. Turn off power to unit. Remove Grill and plug motor into receptacle

in housing. Restore power to unit.

1c. Wiring is not connected properly. 1c. Turn off power to unit. Check that all wires are connected.

1d. Motor has stopped operating. 1d. Replace motor.

2. Fan is operating, but air moves slower than normal. 2. Obstruction in the exhaust ducting. 2. Check for any obstructions in the ducting. The most common are bird nests

in the roof cap or wall cap where the fan exhausts to the outside.

3. Fan is operating louder than normal. 3a. Motor is loose. 3a. Turn off power to unit. Remove grill and check that all screws are fully

tightened. Restore power to unit.

3b. Fan blade is hitting housing of unit. 3b. Call your dealer for service.

LIMITED WARRANTY

All products manufactured by Air King Limited are warranted for one year from the date of purchase against defects in workmanship and/or

material. In addition, all ventilating/exhaust fans, heaters, combination fan lights and/or heaters, and range hoods are guaranteed for five years

from the date of purchase against defects in workmanship and/or material.

This warranty does not cover any labor or shipping costs or the cost of replacement components as part of routine maintenance such as: range

hood grease filters, charcoal filters or combination charcoal/grease filters; replacement light bulbs in range hoods or bathroom fan/light/bulb

heater combinations. As well, any damage or failure caused by abuse, misuse, abnormal usage, faulty installation, or improper maintenance

will not be covered by this warranty.

In order to make a claim on this warranty, you must be the original consumer of the product. You will be required to present to Air King the

original bill of sale showing: date of purchase, place of purchase and model purchased. Failure to meet these requirements will void your

warranty.

Air King will not be held responsible for any bodily injury or damages to personal property or real estate whether caused directly or indirectly

by the product. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some states do

not allow limitations on how long an implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you

specific legal rights and you may have other rights which vary from state to state and province to province.

FOR PARTS OR TECHNICAL ASSISTANCE

Please call: 1-800-465-7300, MONDAY THROUGH FRIDAY, BETWEEN THE HOURS OF 8 AM AND 4:00 PM EST.

PLEASE DO NOT RETURN PRODUCT TO PLACE OF PURCHASE.

Reference the type and style of product (located on label inside of the product) when you call.

For more information please visit our website: wwwairkinglimited.com

www.airkinglimited.com

210572051 Rev. A 8-05 5 of 12

Installer: _________________________________________________________ Installation Date:_________________________________________

Place of Purchase: _________________________________________________ Model Number: __________________________________________

www.airkinglimited.com

210572051 Rev. A 8-05 6 of 12

# Qty. Description Replacement Part #

1 1 Fan Housing 5S1202044

2 2 Mounting Bar 5S1202045

3 4 Nuts 5S1202041

4 1 Metal Collar 5S5202007

5 2 Bushing 5S5202003

6 1 Spring 5S5202008

7 2 Damper 5S5202009

8 1 Rod 5S5202010

9 2 Grill Springs 5S1202046

10 1 Grill 5S1202048

11 2 Flange Screw 5S1202049

12 1 Ceiling Flange 5S1202050

13 2 Nuts 5S1202031

14 2 Blower Grommet 5S1202032

15 1 Blower Housing 5S2202022

16 1 Blower Wheel 5S2202023

17 1 Nut 5S2202014

REPLACEMENT PARTS DIAGRAM

# Qty. Description Replacement Part #

18 1 Motor - AK150LS, AK200LS 5S2202024

1 Motor - AK300LS 5S2202025

19 1 Motor Plate 5S2202020

20 3 Screw 5S2202027

21 5 Screw 5S2202017

22 1 Motor Cap Harness - AK150LS 5S2202012

1 Motor Cap Harness - AK200LS 5S2202010

1 Motor Cap Harness - AK300LS 5S1202051

23 1 Internal Wire Cover - AK150LS, AK200LS 5S1202004

1 Internal Wire Cover - AK300LS 5S1202052

24 6 Screw 5S1999010

25 1 Outlet Gasket 5S1202053

26 1 Collar Gasket 5S1202054

27 1 External Wire Cover 5S1202007

28 1 14 ga Ground Wire 5S1999003

29 1 #10 Ground Screw 5S1999002

LIRE ET CONSERVER CES INSTRUCTIONS

LIRE SOIGNEUSEMENT AVANT DE TENTER D’ASSEMBLER, INSTALLER, OPÉRER OU DE RÉPARER LE PRODUIT DÉCRIT. PROTÉGEZ

VOUS-MÊME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SÉCURITÉ. FAILLIR À SE CONFORMER AUX

INSTRUCTIONS PEUT RÉSULTER EN BLESSURE PERSONNELLE GRAVE ET/OU EN DOMMAGE À LA PROPRIÉTÉ.

CONSERVER CES INSTRUCTIONS POUR RÉFÉRENCES FUTURES.

INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ

Lors de l’utilisation d’appareils électriques, des précautions de base doivent

toujours être suivies pour réduire les risques d’incendie, de choc

électrique et de blessures corporelles, incluant ce qui suit:

1. Bien lire toutes les instructions avant d’installer ou d’utiliser

le ventilateur d’évacuation.

2. Utiliser cette unité seulement de la manière pour laquelle le

fabricant l’a conçu. Si vous aviez des questions, veuillez

contacter le fabricant.

3. Avant d’effectuer un service ou de nettoyer l’unité, couper

l’alimentation électrique dans le panneau de distribution et

verrouiller le dispositif de déconnexion afin d’éviter que

l’alimentation ne revienne accidentellement. Lorsque le

dispositif ne peut être verrouillé, fixer solidement un avis

d’avertissement, tel qu’une étiquette, au panneau de distribution.

4. Le travail d’installation et le câblage électrique doivent être

effectués par une(des) personne(s) qualifiée(s) en conformité

avec tous les codes et normes applicables, incluant la

construction relative aux incendies.

5. De l’air en quantité suffisante est requis pour la bonne

combustion et l’évacuation de gaz par le conduit (cheminée)

provenant d’équipement de brûlage au combustible pour

prévenir un refoulement. Suivre les directives du fabricant

de l’équipement de chauffage et les normes de sécurité telles

que celles publiées par la National Fire Protection Association

(NFPA) et de la American Society for Heating, Refrigeration,

and Air Conditioning Engineers (ASHRAE), et de celles des

autorités locales du code.

Modéles: AK150LS,

AK200LS, AK300LS

www.airkinglimited.com

210572051 Rev. A 8-05

Ventilateur d’Évacuation

CONSERVER CES INSTRUCTIONS

AVERTISSEMENT: POUR USAGE DE VENTILATION

GÉNÉRALE EXCLUSIVEMENT. NE PAS UTILISER POUR ÉVACUER

DU MATÉRIEL ET DES VAPEURS DANGEREUSES OU EXPLOSIVES.

6. Lors de coupe ou de perçage des murs et plafonds, ne pas

endommager le filage électrique et autres utilités cachées.

7. Les ventilateurs avec conduits doivent toujours être évacués

vers l’extérieur.

8. Cette unité doit être mise à la terre.

9. Pour éviter des dommages aux roulements des moteurs et/ou

des hélices bruyantes ou déséquilibrées, empêcher la

poussière de cloison sèche, poussière de construction, etc.,

d’atteindre l’unité de puissance.

AVERTISSEMENT: POUR RÉDUIRE LES RISQUES

D’INCENDIE OU DE CHOC ÉLECTRIQUE, NE PAS UTILISER CE

VENTILATEUR AVEC UN RÉGULATEUR DE VITESSE ÉLECTRONIQUE.

10. Acceptable pour utilisation au-dessus d’une baignoire ou

d’une douche lorsque installé dans un circuit protégé par un

disjoncteur de fuite de terre.

11. NE JAMAIS placer un interrupteur à un endroit qui puisse

être atteint de la baignoire ou de la douche.

AVERTISSEMENT: NE PAS UTILISER DANS LES CUISINES

INSTRUCTIONS IMPORTANTES –

MANUEL D’OPÉRATION

7 of 12

1c. Installation sur des solives de 61 cm (24 po) au centre ou plus

larges que des solives de 40,6 cm (16 po): Installer deux chevêtres

de 5,08 cm x 10,16 cm (2x4 po) (non-compris) entre les solives

(Figure 4). Installer les supports de montage dans le second jeu de

fentes sur le châssis du ventilateur et fixer en place avec les quatre

écrous #10-32 inclus tel qu’indiqué. Centrer le châssis du ventilateur

entre les solives et fixer les supports de montage avec des vis ou

des clous (non-compris) au chevêtre. Ajuster la hauteur du châssis

pour qu’il soit à effleurement avec le plafond fini en desserrant les

écrous de support de montage et en glissant le châssis vers le

haut ou vers le bas sur le support de montage. Serrer à fond tous

les quatre écrous pour fixer le châssis en place. (Figure 5).

SECTION 3

Conduits

AVERTISSEMENT: TOUS LES CONDUITS DOIVENT ÊTRE

CONFORMES AUX CODES DU BÂTIMENT LOCAUX ET NATIONAUX.

1. Raccorder le conduit au collet de conduit du ventilateur (Figure 6).

Fixer en place à l’aide de ruban ou de serre-joint. Toujours évacuer

le ventilateur vers l’extérieur au travers de chapeau mural ou de toit.

INSTRUCTIONS D’INSTALLATION

AVERTISSEMENT:

VOUS ASSURER QUE L’ALIMENTATION

EST COUPÉE AU PANNEAU DE SERVICE AVANT DE COMMENCER

L’INSTALLATION.

SECTION 1

Préparation du Ventilateur d’évacuation

1. Sortir le ventilateur de sa boite et confirmer que toutes les pièces

sont présentes. En plus du ventilateur d’évacuation vous devriez avoir:

1 - Grille

1 - Ensemble de clapet (attaché)

2 - Supports de montage

1 - Bride de montage

4 - Écrous 10-32

1 - Feuillet d’instructions / sécurité

2. Choisir un emplacement pour votre ventilateur. Pour assurer la

meilleure performance du débit d’air et sonore, il est recommandé

que la longueur des conduits et que le nombre de coudes soient

gardés au minimum et que des conduits rigides isolés soient utilisés.

Ce ventilateur nécessitera au moins

20,3cm (8po) de dégagement dans le

plafond ou le mur, et s’installe au travers

de cloison sèche d’une épaisseur de

jusqu’à 1,9cm (3/4po).

3. Sélectionner l’alvéole défonçable la

mieux appropriée et l’enlever à l’aide d’un

tournevis à lame plate (Figure 1).

SECTION 2

Montage du Châssis

1a. Installation sur des solives en 5,08 cm x 10,16 cm (2x4 po) au centre

de 40,6 cm (16 po): Installer les supports de montage dans le second

jeu de fentes sur le châssis du ventilateur et fixer en place avec les

quatre écrous #10-32 inclus tel qu’indiqué. Centrer le châssis du

ventilateur entre les solives et fixer les supports de montage avec

des vis ou des clous (non-compris) à la solive. Ajuster la hauteur du

châssis pour qu’il soit à effleurement avec le plafond fini en desserrant

les écrous de support de montage et en glissant le châssis vers le

haut ou vers le bas sur le support de montage. Serrer à fond tous

les quatre écrous pour fixer le châssis en place. (Figure 2).

1b. Installation sur des solives en 5,08 cm x 15,24 cm (2x6 po) au centre