Vermont Castings GPFMP Manuel utilisateur

Marque: Vermont Castings

Modèle: GPFMP

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

Vermont Castings Gas Patio Fire

INSTALLER / CONSUMER

SAFETY INFORMATION

PLEASE READ THIS MANUAL

BEFORE INSTALLING AND

USING APPLIANCE

IMPORTANT: Installation of natu-

ral gas should be completed by a

qualified installer, service agency

or gas supplier.

WARNING: If the information in

this manual is not followed ex-

actly, a fire or explosion may

result causing property damage,

personal injury or loss of life.

FOR YOUR SAFETY

• Installation and service must be

performed by a qualified in-

staller, service agency or the gas

supplier.

• Do not store or use gasoline or

other flammable vapors and

liquids in the vicinity of this or

any other appliance.

FOR YOUR SAFETY:

If you smell gas:

• Do not touch any electrical

switches

• Do not try to light any appliance.

Extinguish any open flame

• Do not use the phone in your

building

• Immediately call your gas sup-

plier from a neighbor’s phone

• Follow your gas supplier’s in-

structions

• If you cannot reach your gas

supplier, call the fire department

WARNING: For outdoor use only!

WARNING:

Do not use for cooking!

Gas Patio Fire

Models: GPFMN, GPFMP

4237

Homeowner’s Installation and

Operating Manual

9DX5

ANSI Z21.58-1995; CGA 1.6-M95;

IAS/US 4-96

INSTALLER: Do Not Discard This Manual,

Leave For Homeowner

20004237 5/02 Rev. 4

Vermont Castings Gas Patio Fire

Table of Contents

General Information ............................................... 2

Specifications......................................................... 3

Assembly & Installation.......................................... 4

Log Placement ....................................................... 7

Operation ............................................................. 10

Maintenance ........................................................ 11

Replacement Parts .............................................. 12

Accessories.......................................................... 13

General Information

Model GPF is a decorative gas log set for outdoor use

only. This appliance must not be used for cooking.

IMPORTANT: Read all instructions and warnings

carefully before starting installation. Failure to follow

these instructions may result in a possible fire hazard

and will void the warranty.

WARNING: Improper installation, adjustment, alter-

ation, service or maintenance can cause injury or

property damage. Read the installation, operating and

maintenance instructions thoroughly before installing or

servicing this equipment.

WARNING: This appliance shall be used only outdoors

in a well-ventilated space and shall NOT be used inside

a building, garage or any other enclosed area.

WARNING: This log set must NOT be installed in an

unvented appliance.

WARNING: This unit is not for use with solid fuel.

NOTE: All new LP cylinders (and in many cases used

cylinders) may contain water, air or other contaminants.

It is essential that these be removed before filling the

cylinder and placing into service. Water vapor present

in the gas vapor may cause the regulator to “freeze up”

and cause an interruption to the gas flow. This interrup-

tion will cause the unit to shut down. To prevent this

from occurring, it is essential that a qualified individual

ALWAYS purge a new tank thoroughly before placing it

into service. It is recommended that cylinders that have

not been used for extended periods of time also be

purged before use.

The installation must conform with Local Codes or, in

the absence of local codes, with the National Fuel Gas

Code ANSI Z223.1 or CSA-B149.1 Installation Code.

The appliance and its individual shut off valve must be

disconnected from the gas supply piping system during

any pressure testing or the system at test pressure in

excess of 1/2 psig (3.5kPa).

This appliance must be isolated from the gas supply

piping system by closing its individual manual shut off

valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than

1/2 psig (3kPa).

Always keep the appliance area clear and free from

combustible materials, gasoline and other flammable

vapors and liquids.

• Children and adults should be alerted to the hazards of

high surface temperatures and should stay away to

avoid burns or clothing ignition.

•Young children should be carefully supervised when

they are in the area of the appliance.

• Never leave the unit unattended during operation.

• Clothing or other flammable materials should not be

hung from the appliance, or placed on or near the

appliance.

• Installation and repair should be done by a qualified

service person. The appliance should be inspected

before use and at least annually by a qualified service

person. More frequent cleaning may be required as

necessary. It is imperative the control compartment,

burners and circulating air passageways of the appli-

ance be kept clean.

• Inspect the fuel supply connection (including the hose

for LP models) before each use of the appliance.

• If it is evident there is excessive abrasion or wear, or

the hose is cut, it must be replaced prior to the appli-

ance being put into operation.

• The pressure regulator and hose assembly supplied

with LP models must be used. Replacement pressure

regulators and hose assemblies must be those speci-

fied in this manual.

• The LP gas supply cylinder used with LP models must

be constructed and marked in accordance with the

specifications for LP gas cylinders of the U.S. Depart-

ment of Transportation (DOT) or the specifications in

the National Standard of Canada, CAN/CSA B330,

Cylinder, Spheres and Tube for Transportation of

Dangerous Goods as applicable.

• Cylinders must be stored outdoors in a well-ventilated

area out of reach of children. Disconnected cylinders

must have threaded valve plugs tightly installed and

must not be stored in a building, garage or any other

enclosed area.

• Storage of this appliance indoors is permissible only

if it has been disconnected form its fuel supply

(natural gas line or LP gas cylinder).

• The LP gas cylinder supply system must be arranged

for vapor withdrawal.

• The LP gas cylinder used must include a collar to

protect the cylinder valve.

• When an LP model is not in use, the LP gas must be

turned off at the supply cylinder.

Vermont Castings Gas Patio Fire

GPF Dimensions

11¹⁄₂"

(292mm)

(127mm)

12"

(305mm)

3¹⁄₄"(83mm)

16¹⁄₄"

(413mm)

11³⁄₈"

(289mm)

8¹⁄₄"

(210mm)

Burner

4237

Fig. 1 Physical dimensions.

Burner Assembly

Flex Line

Valve

Propane

Regulator/Hose

Natural

Gas Hose

FP1129

Fig. 2 GPF parts.

Gas Specifications

Max. Input

Model Fuel Btu/Hr

GPFMN Natural Gas 75,000

GPFMP Propane Gas 65,000

Gas Inlet Pressures

Natural LP (Propane)

Minimum Inlet Pressure 5.5” w.c. 11.0” w.c.

Maximum Inlet Pressure 14.0”w.c. 14.0” w.c.

Minimum Clearance to Combustibles

Inches mm

Floor 0 0

Side Walls 16 406

Top of unit to ceiling 7 ft. 2.1m

Vermont Castings Gas Patio Fire

Assembly and Installation

The logs and burner assembly are shipped together.

1. Remove the gas log set and burner assembly and

check for damage. DO NOT install damaged compo-

nents. The logs are fragile - handle with care.

2. Place the burner assembly on a flat, stable surface

in an outdoor location such as a patio or a deck.

This location must be adjacent to the gas supply line

(natural gas) or LP gas supply cylinder. NOTE:

Minimum clearances to combustibles must be

maintained. (Refer to Page 3)

Remember, you must have easy access to the gas

valve control knob AFTER the appliance is installed and

connected to the gas supply.

The ON/OFF Gas Valve is used to turn gas to the

burner on and off.

Natural Gas Models

Connect the incoming gas supply line to the on/off gas

valve of the appliance. (Fig. 3) Make certain ALL gas

connections are tight. Test for leaks. Use a 50/50

solution of liquid soap and water to test for leaks at gas

fittings and joints. Apply water/soap solution with a

brush only -

do not over apply. NEVER test with an

open flame.

LP Gas Models

1. Place cylinder base (provided with unit) on a level

surface.

2. Be sure to place cylinder in ring on base.

3. Make sure tank valve is in its full OFF position. (Turn

clockwise to stop.)

4. Check tank valve features to ensure it has proper

external mating threads. (Tank valve marked: USE

WITH TYPE 1)

5. Inspect hose shipped with the unit for damage.

Never attempt to use damaged or plugged equip-

ment. See your local LP Gas Dealer for repairs.

6. After inspecting the LP hose shipped with the unit,

connect the end with the female fitting on the hose

to the male fitting on the on/off gas valve at the end

of the flex tube and make sure it is tight.

7. When connecting regulator assembly to the tank

valve, hand tighten nut clockwise to a positive stop.

DO NOT use a wrench to tighten. Use of a wrench

may damage quick closing coupling nut and result in

a hazardous condition. (Fig. 3)

8. Locate the hose out of pathways where people may

trip over it or in areas where the hose may be

subject to accidental damage.

9. Open tank valve fully (counterclockwise). Turn the

on/off valve at the unit slowly to the on position and

use a 50/50 solution of liquid soap and water to test

for leaks at gas fitting and joints. Apply water/soap

solution with a brush only -

do not over apply.

NEVER test with an open flame.

If a leak is found,

turn tank valve off and do not use the appliance

until repairs can be made by a local LP Gas Dealer.

DO NOT attempt to make repairs yourself.

10. Never attempt to use this appliance or any compo-

nents that have been damaged or exposed to an

accidental fire.

Natural Gas Supply

Line

Propane

Regulator Hose

Cylinder Base

Burner

Assembly

Burner

Assembly

Valve

FP1130

Fig. 3 Gas line connection.

Vermont Castings Gas Patio Fire

Enclosures for LP Gas Supply Systems

If you build an enclosure for an LP gas cylinder, follow

these recommended specifications. You must also

follow local codes.

Enclosures for LP gas supply cylinders shall be

ventilated by openings at the level of the cylinder valve

and at floor level. The effectiveness of the opening(s)

for purposes of ventilation shall be determined with the

LP gas supply cylinder(s) in place. This shall be accom-

plished by one of the following:

1. One side of the enclosure shall be completely open;

2. For an enclosure having four sides, a top and

bottom:

a. At least two ventilation openings at cylinder valve

level shall be provided in the side wall, equally

sized, spaced at 180 degrees (3.14 rad), and

unobstructed. Each opening shall have a total

free area of not less than 1/2 square inch per

pound (3.2 sq. cm/kg) of stored fuel capacity and

not less than a total free area of 10 square inches

(64.5 sq. cm)

b. Ventilation opening(s) shall be provided at floor

level and shall have a total free area of not less

than 1/2 inch per pound (3.2 sq. cm/kg) of stored

fuel capacity and not less than a total free area of

10 square inches (64.5 sq. cm). If ventilation

openings at floor level are in a side wall, there

shall be at least two openings. The bottom of the

openings shall be at floor level and the upper

edge no more than 5 inches (127mm) above the

floor. The openings shall be equally sized,

spaced at 180 degrees (3.14 rad) and unob-

structed.

c. Every opening shall have minimum dimensions

so as to permit the entrance of a 1/8 inch

(3.2mm) diameter rod.

3. Cylinder valves shall be readily accessible for hand

operation. A door on the enclosure to gain access to

the cylinder valve is acceptable, provided it is

nonlocking and can be opened without the use of

tools.

4. There shall be a minimum clearance of 2 inches

(50.8mm) between the lower surface of the floor of

the LP gas supply cylinder enclosure and the

ground.

5. The design of the enclosure shall be such that (1)

the LP gas supply cylinder(s) can be connected,

disconnected and the connections inspected and

tested outside the cylinder enclosure; and (2) those

connections which could be disturbed when install-

ing the cylinder(s) in the enclosure can be leak

tested inside the enclosure.

6. Be certain to mount or set the LP gas cylinder on a

flat surface and restrain it to prevent it from tipping.

Purge the gas supply line of any trapped air prior to the

first firing of the unit.

WARNING: During the initial purging and subse-

quent lightings, NEVER allow gas valve to remain in

the “Open” position without first placing a burning

match on top of the burner.

Vermont Castings Gas Patio Fire

Installation of GPF in Optional Villa Base

The Villa Base is designed as a decorative enhance-

ment for use with the Gas Patio Fire.

Tools required: 7/16”, 3/4” and 11/16” wrenches, phillips

screwdriver.

Installation Instructions

1. Remove octagonal plate from shipping carton.

2. Remove base/Villa from shipping carton. Remove

four (4) 1/4-20 fasteners, four (4) nuts and eight (8)

washers that fasten the base to the Villa. Remove base.

Remove two (2) 1/4-20 x 1/2” fasteners, two (2) wash-

ers from cast valve panel. Set hardware aside. (Fig. 4)

3. Invert the base and locate the Villa on the base.

Orient the Villa so the 3/4” diameter hole in the Villa’s

valve panel is facing 90° from the fuel line opening in

the base. Replace the fasteners, nuts and washers

removed in step 1. Be sure to use washers under both

the fastener heads and nuts. Tighten the fasteners

tight, but do not overtighten. (Fig. 5)

4. Remove the four (4) sheet metals screws that hold

the valve bracket to the leg support on the GPF and

discard.

5. Disconnect the fuel supply line from the valve using

a 3/4” wrench. Using both the 3/4” and 11/16”

wrenches, remove the fuel supply line from the venturi

(tube secured to the bottom of the burner). Assemble

Valve Bracket

Valve

Panel

Fuel Line

Opening

KT261

Fig. 5 Secure Villa to base.

mounting plate on the Villa. (Fig. 6) Orient the plate with

the long side of the rectangular opening parallel to the

valve panel. Pass the fuel line through the rectangular

opening and reconnect the fuel supply line to the

venturi on the GPF and tighten using the 3/4” and

11/16” wrenches.

GPF Burner

Assembly

Octagonal

Plate

KT262

Fig. 6 Set the octagonal plate on the Villa, then place the

GPF burner.

6. Seat the GPF burner assembly on the Villa. Pass

the burner legs through the rectangular opening in the

plate. (Fig. 7)

7. Continue with volcanic rock and log placement on

page 7.

Two optional bases are available for the Gas Patio Fire.

The Villa and the Chalet are available from your Ver-

mont Castings, Majestic Products dealer. You may also

construct your own base from noncombustible materi-

als (stone or brick) for use with the Gas Patio Fire. The

Gas Patio Fire may be placed directly on a hard flat

combustible surface (deck).

the valve and bracket assembly to the villa using the

1/4-20 x 3/8” fasteners and washers removed in Step 2.

Reconnect the fuel supply line to the valve and tighten.

Feed the fuel line from the gas supply through the fuel

line opening in the base. (Fig. 5) Place the octagonal

Octagonal Plate

Base

Valve

Panel

Villa

KT260

Fig. 4 Remove base/Villa from shipping container. Remove

base from Villa.

Vermont Castings Gas Patio Fire

Installation of GPF on

Optional Chalet Base

The Chalet Base is designed as a decorative enhance-

ment for use with the Gas Patio Fire.

Tools required: 7/16”, 3/4” and 11/16” wrenches, phillips

screwdriver.

Installation Instructions

1. Remove Chalet Base assembly from shipping

carton. Remove two (2) 1/4-20 fasteners and two (2)

washers from the cast valve panel, set aside.

2. Remove the four (4) sheet metal screws that hold

the valve brackets to the burner on the GPF and

discard.

3. Disconnect the fuel supply line from the valve using

a 3/4” wrench. (Fig. 7) Using both the 3/4” and 11/16”

wrenches, remove the fuel supply line from the venturi

(tube secured to the bottom of the burner). Assemble

the valve and bracket assembly to the Chalet using the

1/4-20 x 1/2” fasteners and washers removed in Step 2.

Reconnect the fuel supply line to the valve and tighten.

Feed the fuel line from the gas supply through the fuel

line opening in the base. Place the octagonal mounting

plate on the Chalet. (Fig. 8) Orient the plate with the

long side of the rectangular opening parallel to the

valve panel. Pass the fuel line through the rectangular

opening and reconnect the fuel supply line to the

venturi on the GPF and tighten using the 3/4” and

11/16” wrenches.

4. Seat the GPF burner assembly on the Chalet. Pass

the burner legs through the rectangular opening in the

plate. (Fig. 8)

5. Continue with volcanic rock and log placement on

page 7.

Cast Valve Panel

Valve

Valve Brackets

KT264

Fig. 7 Attach valve and brackets to cast valve brackets.

Log & Volcanic Rock Placement

Remove logs from packaging and examine each for

damage. If any logs are damaged or missing, contact

your dealer. DO NOT install damaged logs.

Volcanic Rock Placement

Pour volcanic rock into outer ring and over burner.

Make sure the volcanic rock is level with the outer ring

and builds up to cover the burner.

Log Placement

1. Arrange logs on floor near burner according to

Figure 9. As shown in Figure 9, the bottom of the

logs will be toward the outside of the burner ring.

2. Use flex line as reference. Begin with line to your

left.

C5 C6

Fig. 9 GPF logs.

LG161

GPF Burner

Assembly

Octagonal

Plate

Cast

Valve

Panel

Valve and Bracket

KT263

Fig. 8 Cutaway section of Chalet Base.

Locator Pins

Burner Pan

Volcanic Rock

Flex

Line

Burner

Ring

Fig. 10 Arrange volcanic rock evenly around and on burner

pan.

Vermont Castings Gas Patio Fire

3. Place volcanic rock evenly around and on burner

pan if you have not already done so. (Fig. 10)

4. Place log C1 on burner, using locator pins and

holes in bottom of log. (Fig. 11)

Log C1

LG162a

Fig. 11 Place log C1 on locator pins onburner.

5. Move around so that flex line is now on your right.

Place log C2 with “Y” part of log toward the outside

of the burner ring. (Fig. 12)

Log C2

Log C1

LG163a

Fig. 12 Log C2 placement.

6. Place logs C3 and C4 with flex line on your left. C3

fits just under angle of log C2. (Fig. 13)

7. Log C4 rests with ends of “Y” section on burner ring.

Top of log rests on log C2.

8. Flex line on right. Place log C5 with the notch at the

top resting next to log C3. (fig. 14)

9. Flex line on left. Place log C6 so the top of the log is

over log C3 and bottom of log is over corner of the

burner pan. (Fig. 15)

CAUTION

The logs are fragile. Use caution when placing the

cover on, or removing the cover from, the unit to

avoid damaging the logs.

Log C4

Log C2

Log C1

Log C3

LG164a

Fig. 13 Logs C3 & C4 placement.

Log C5

Log C4

Log C2

Log C1

LG165a

Fig. 14 Log C5 placement.

Log C5

Log C4

Log

Log C6

Log C2

Log C3

LG166a

Fig. 15 Log C6 placement.

Vermont Castings Gas Patio Fire

Optional GPF Cover Assembly

1. Lay all parts on the floor.

2. Attach all three frame stands to the top and bottom

rings using bolts and nuts provided. (Fig. 16)

Top Ring

Bottom Ring

Frame

Stands

FP1164

Fig. 16 Attach frame stands to top and bottom rings.

3. Place vinyl cover on the floor with the opening facing

up. Insert the frame assembly into the cover. (Fig. 17)

Vinyl Cover

FP1163

Fig. 18 Use velcro straps to hold vinyl cover to frame.

4. Use the three inside velcro straps to hold the vinyl

cover to the frame. (Fig. 18)

5. Turn the cover with the frame over and it is ready to

use.

Before using the vinyl cover turn the GPF flame to

OFF and wait unit the unit is completely cool.

When using the optional screen mesh on the GPF,

the metal support assembly needs to be removed

from inside the vinyl cover.

Frame

Assembly

Vinyl

Cover

FP1162

Fig. 17 Insert frame assembly into vinyl cover.

CAUTION: Do not leave burner on with the

cover on!

Vermont Castings Gas Patio Fire

Operation

Upon completing the gas line connection, a small

amount of air will be in the lines. When first lighting the

burner, it will take a few seconds for the lines to purge

themselves of this air. Once the purging is complete,

the burner will light and operate as indicated in the

instruction manual. Subsequent lighting of the appli-

ance will not require such purging.

WARNING: Read and follow the Safety and Lighting

Instructions page in this manual and on labels on the

appliance. IF YOU DO NOT FOLLOW THESE IN-

STRUCTIONS PRECISELY, A FIRE OR EXPLOSION

MAY RESULT AND YOU MAY BE SERIOUSLY IN-

JURED!

Lighting and Operating Instructions

FOR YOUR SAFETY, READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance must be lit manually. When lighting,

follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance

area for gas. Be sure to smell next to the floor

because some gas is heavier than air and will settle

on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance

• Do not touch any electric switch

• Do not use any phone in your building

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions

• If you cannot reach your gas supplier, call the fire

department

C. Use only your hand to turn the gas control key.

Never use tools. If the key will not turn by hand, do

not try to repair it, call a qualified service technician.

Applying force or any attempted repair may result in

a fire or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualified service technician

to inspect the appliance and to replace any part of

the gas control which has been under water.

Lighting Instructions

1. STOP! Read the safety information above.

2. Remove the cover.

3. Insert the “TEE” handle in the valve.

4. Hold the log lighter towards the center of the burner.

• For Natural Gas unit, turn the “TEE” handle

slowly counterclockwise .

• For LP unit, turn valve on the LP tank counter-

clockwise all the way and then turn the

“TEE” handle on the valve slowly counterclock-

wise .

5. If the burner does not light immediately, turn the gas

valve to “OFF”.

6. Wait at least five (5) minutes to clear out any gas.

Then smell for gas, including near the floor. If you

smell gas, STOP! Follow “B” in the safety informa-

tion above. If you do not smell gas, repeat steps.

To Turn Off Gas to Appliance

1. Turn the “TEE” handle to the “OFF” position, fully

clockwise at the unit, then turn the valve on

the LP tank to the “OFF” position, fully clockwise

. Remove “TEE” handle.

2. Replace cover, when unit has completely cooled.

Vermont Castings Gas Patio Fire

1. The appliance should be inspected before initial use

and inspected and cleaned at least annually by a

qualified field service person.

2. Tampering is DANGEROUS and voids all warran-

ties. Any component that is found to be faulty, must

be replaced with an approved component.

3. To obtain proper operation, it is imperative that the

burner flame characteristics are steady, not lifting or

floating. Check the burner flame patterns with Figure

19.

Maintenance

LG168

Fig. 19 GPF flame appearance.

4. Periodically remove the logs and examine the

burner. If dirty, clean with a soft brush. Also examine

the area around the burner air shutter. Any dirt or lint

in this area should be removed. This will ensure long

life and trouble free operation. When the appliance

is put back in service, check the burner flame

patterns with Figure 20. Reinstall the logs as shown

in the log placement instructions.

5. Periodically check the hose connecting the LP gas

cylinder to ensure it is not damaged in any way.

NOTE: Carbon (soot) may build up on the surface of

the logs with heavy use. This is more likely to occur

when using LP gas. The soot should be cleaned off the

surface of the logs periodically to prevent excessive

build up. To clean the logs, be sure the fire is out, the

gas supply is turned off and the logs are cool to the

touch. The soot can then be brushed off with a dry

bristle brush or cloth. Take care while cleaning the logs

LG169

Fig. 20 Correct burner flame appearance.

as they can become damaged if mishandled. Care

should be taken to dispose of the soot and cleaning

materials properly. Keep away from clothing and

outdoor furniture.

High Elevation Installation

This U.L. listed gas appliance is tested and approved

for elevations from 0 to 2,000 feet in the U.S. and form

0 to 4,500 feet in Canada.

When installing this appliance at an elevation above

2,00 feet (in the U.S.), it may be necessary to decrease

the input rating by changing the existing burner orifice

to a smaller size. Input should be reduced four percent

(4%) for each 1,000 feet above sea level, unless the

heating value of the gas has been reduced, in which

case this general rule will not apply. To identify the

proper orifice size, check with the local gas utility.

When installing this unit at an elevation between 2,000

and 4,500 feet (in Canada), the input rating must be

reduced by ten percent (10%).

When installing this unit at an elevation above 4,500

feet (in Canada), check with local authorities.

Consult your local gas utility for assistance in determin-

ing the proper orifice for your location.

Vermont Castings Gas Patio Fire

7a,b

4237

Vermont Castings, Majestic Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and

products at any time, without notice.

GPF

Item / Model Number Part Number

1. Complete Log Set 20004457

1a. Log C1 20004451

1b. Log C2 20004452

1c. Log C3 20004454

1d. Log C4 20004453

1e. Log C5 20004455

1f. Log C6 20004456

2. Burner Assy. 20003733

3. Hose/Regulator Assy. - LP 20004640

4. Cover 20004450

5. Dante Valve 20004482

6. Natural Supply Line 50000198

7a. Short Stem Orifice - Natural 20005016

7b. Short Stem Orifice - LP 20004498

8. Volcanic Rock 20000198

9. LP Gas Cylnder Base 20004578

10. LP Conversion Kit 20004752

11. Natural Conversion Kit 20004753

Contact The Vermont Castings Majestic Products

Company with questions concerning prices and policies

covering replacement parts. Parts may be ordered

through your distributor or dealer.

You will need the following information when ordering

replacement parts:

• The appliance model number.

• The serial number.

• A description of the part.

Should you need additional information beyond what

your dealer can furnish, contact:

The Vermont Castings Majestic Products Company

410 Admiral Blvd.

Mississauga, Ontario

Canada L5T 2N6

Vermont Castings Gas Patio Fire

Accessories

The following accessories for these appliances are available from your local Vermont Castings, Majestic Products

distributor. Each accessory comes with a separate installation instructions for the particular appliance. Be sure to read

each instruction thoroughly before installing.

Description Model Number

Patio Fire Optional Screen Kit PFOSK

Villa Patio Fire (Urn) Base PFCBVMB

Chalet Patio Fire (Octagonal) Base PFCBCMB

CAUTION: This appliance is a highly engineered system, and, as such, must be operated only with Vermont

Castings, Majestic Products approved components. If you use an unapproved component to make any

modifications, you may create a possible fire hazard and will void Vermont Castings, Majestic Products

warranty. In addition, such action may void the coverage provided by the owner’s insurance.

Vermont Castings Gas Patio Fire

LIMITED WARRANTY & EXTENDED LIFE TIME PROTECTION

For Vermont Castings Gas Appliance Products*

BASIC WARRANTY

The Vermont Castings Majestic Products company (hereinafter referred to

collectively as the “Company”) warrants that your new Vermont Castings Gas

Appliance is free from manufacturing and material defects for a period of one year

from date of installation, subject to the following conditions and limitations.

EXTENDED LIFETIME WARRANTY

The heat exchanger, combustion chamber and ceramic burner parts of every*

Vermont Castings, Majestic Products products are warranted for life to the original

owner, subject to proof of purchase and the following conditions and limitations:

1. This new Vermont Castings product must be installed by a competent,

authorized service contractor. It must be installed and operated at all times in

accordance with the installation and Operating Instructions furnished with the

product. Any alteration, willful abuse, accident or misuse of the product shall

nullify this warranty.

2. This warranty is nontransferable, and is made to the original owner, provided

that the purchase was made through an authorized supplier of the Company.

3. This warranty is limited to the repair or replacement of part(s) found to be

defective in material or workmanship, provided that such part(s) have been

subjected to normal conditions of use and service, after said defect is

confirmed by the Company’s inspection.

4. The Company may, at its discretion, fully discharge all obligations with respect

to this warranty by refunding the wholesale price of the defective part).

5. Any installation, labor, construction, transportation, or other related costs/

expenses arising from defective part(s), repair, replacement, or otherwise of

same, will not be covered by this warranty, nor shall the Company assume

responsibility for same. Further, the Company will not be responsible for any

incidental, indirect, or consequential damages, except as provided by law.

6. All other warranties - expressed or implied - with respect to the product, its

components and accessories, or any obligation/liabilities on the part of the

Company are hereby expressly excluded.

7. The Company neither assumes, nor authorizes any third party to assume, on

its behalf, any other liabilities with respect to the sale of this Vermont Castings

product.

8. The warranties as outlined within this document do not apply to chimney

components or other non Vermont Castings accessories used in conjunction

with the installation of this product.

9. The Company will not be responsible for:

a) Down drafts or spillage caused by environmental conditions such as

nearby trees, buildings, roof tops, hills or mountains.

b) Inadequate ventilation or negative air pressure caused by mechanical

systems such as furnaces, fans, clothes dryers, etc.

10. This warranty is void if:

a) The fireplace has been operated in atmospheres contaminated by chlorine,

fluorine or other damaging chemicals.

b) The fireplace is subjected to prolonged periods of dampness or condensa-

tion.

c) Any damage to the fireplace, combustion chamber, heat exchanger or

other components due to water, or weather damage which is the result of,

but not limited to, improper chimney/venting installation.

d) Any alteration, willful abuse, accident, or misuse of the product.

GLASS DOORS & BRASS PLATED PARTS

Glass doors are not warranted for breakage due to misuse or accident.

Brass parts should be cleaned with lemon oil only. Brass cleaners cannot be used.

Mortar mix and masonry cleaners may corrode the brass finish. The Company will

not be responsible for, nor will it warrant any brass parts which are damaged by

external chemicals or down draft conditions.

IF WARRANTY SERVICE IS NEEDED:

1. Contact your supplier. Make sure you have your warranty, your sales receipt,

and the model/serial number of your Vermont Castings product.

2. DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.

*Vermont Castings, Majestic Products products bearing this

special Warranty Seal of Approval, carry a comprehensive

Limited Lifetime Warranty. This includes the Insta-Flame

Ceramic Burners, Heat Exchange System and Combustion

Chamber. All other parts are covered for one year.

GARANTIE DE BASE:

Vermont Castings, Majestic Products (aux présentes nommée la "Société")

garantit votre nouveau foyer au gaz Vermont Castings contre tous défauts de

fabrication et de matières premières pour une période d'un an à compter de la

date d'installation, sujet aux conditions et limitations suivantes.

GARANTIE A VIE PROLONGEE:

Les pièces de l'échangeur de chaleur, de la chambre à combustion et du brûleur

en céramique de tout produit *Vermont Castings, Majestic Products sont

garanties pour la vie de l'acheteur d'origine, le tout sujet à une preuve d'achat

et aux conditions et limitations suivantes:

1. Ce nouveau produit Vermont Castings doit être installé par un entrepreneur

de service autorisé et compétent. Il doit être installé et utilisé en tout temps

selon les instructions d'installation et de fonctionnement fournies avec le produit.

Toute altération, abus volontaire, accident ou mauvais usage du produit annulera

cette garantie.

2. Cette garantie n'est pas transférable et est offerte à l'acheteur au détail d'origine,

à condition que l'achat soit effectué par l'entremise d'un détaillant autorisé de la

Société.

3. Cette garantie est limitée à la réparation ou au remplacement de(des) pièce(s)

trouvée(s) défectueuse(s) en matières premières ou main-d'oeuvre, à condition

que lesdites pièces aient été sujettes aux conditions normales d'usage et de

service, après que ledit défaut a été confirmé par une inspection par la Société.

4. La Société peut, à sa discrétion, se décharger entièrement de toutes obligations

se rapportant à cette garantie en remboursant le prix de gros de la(des) pièce(s)

défectueuse(s).

5. Tous les frais/dépenses d'installation, de main-d'oeuvre, de construction, de

transport ou autres causés par une (des) pièce(s) défectueuse(s), une réparation,

un remplacement ou autre, ne seront pas couverts sous cette garantie, et la

Société n'assume aucune responsabilité pour ceux-ci. De plus, la Société ne

pourra être tenue responsable pour tous dommages fortuits ou indirects sauf la

ou prévu par la loi.

6. Toutes autres garanties, exprimées ou sous-entendues, en ce qui a trait au

produit, ses composants et accessiores, ou toutes obligations/responsabilités

de la part de la Société sont aux présentes expressment excluses.

7. La Société n'assume et n'autorise personne à assumer, en son nom, toutes

responsabilités en ce qui a trait à la vente de ce produit Vermont Castings.

8. Les garanties, telles que décrites dans ce document, ne s'appliquent pas aux

compasants de cheminée ou aux autres accessoires non Vermont Castings

utilisés conjointement pour l'installation de ce produit.

9. La Société n'encourrera aucune responsabilité pour . . .

a) Les refoulements de cheminées ou débordements causés par les conditions

environnementales comme par les arbres, les édifices, les toits, les côteaux

ou les montagnes adjacents.

b) Une ventilation inadéquate ou une pression d'air négative causée par des

systèmes mécaniques comme les fournaises, les ventilateurs, les

sécheuses, etc.

10. Cette garantie est nulle si:

a) Le foyer a été utilisé dans une atmosphère contaminée par du chlore, du

fluor ou tous autres produits chimiques.

b) Le foyer est assujetti à de longues périodes d'humidité ou de condensation.

c) Des dommages sont causés au foyer, à la chambre de combustion. à

l'échangeur de chaleur ou aux autres composants par de l'eau ou par la

température qui est le résultat mais sans y être limité, d'une mauvaise

installation de cheminée/ventilation.

d) Toute altération, abus volontaire, accident ou mauvais usage du produit

annulera cette garantie.

PORTES EN VERRE & PIECES PLAQUEES LAITON

Les portes en verre ne sont pas garanties contre le bris causé par un mauvais

usage ou un accident.

Les pièces en laiton devraient être nettoyées qu'avec de l'essence de citron. Les

nettoyeurs de laiton ne peuvent pas être utilisés. La Société ne sera pas responsable

pour, et ne garantit pas les pièces en laiton qui sont endommagées par des conditions

chimiques externes ou de refoulement.

SI UN SERVICE SOUS GARANTIE EST REQUIS . . .

1. Communiquez avec votre détaillant. Assurez-vous que vous avez votre garantie,

votre reçu de caisse ainsi que le numéro de modèle/série de votre produit

Vermont Castings.

2. NE TENTEZ PAS D'EFFECTUER DES REPARATIONS VOUS-MEME.

*Les foyers à gaz Vermont Castings, Majestic Products portant ce scean

d'approbatic de la garantie spéciale sont couverts par une

garantie limitée à vie. Celle-ci inclue les brüleurs en

céramique Insta-Flame, le'échangeur de chaleur et la

chambre à combustion. Toutes les autres pièces sont

couverte pour un an.

410 Admiral Blvd.

Mississauga ON L5T 2N6

Vermont Castings Gas Patio Fire

410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777

www.majesticproducts.com • www.vermontcastings.com

Vermont Castings, Majestic Products

Vermont Castings GPFMP Manuel utilisateur

Marque: Vermont Castings

Modèle: GPFMP

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Vermont Castings GPFMP User manual

Vermont Castings GPFMP Manuel utilisateur

Ce manuel convient également à

Vermont Castings GPFMP Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents