Vermont Castings Stardance SNV30RP Manuel utilisateur

Marque: Vermont Castings

Modèle: Stardance SNV30RP

Catégorie: Cheminées

Taper: Manuel utilisateur

INSTALLER / CONSUMER

SAFETY INFORMATION

20007067 1/07 Rev. 8

PLEASE READ THIS MANUAL

BEFORE INSTALLING AND USING

APPLIANCE.

WARNING!

IF THE INFORMATION IN THIS

MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL

INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY

Installation and service must be

performed by a qualiﬁed installer,

service agency or the gas suppler.

WHAT TO DO IF YOU SMELL

GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from your neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the ﬁre department.

DO NOT STORE OR USE

GASOLINE OR OTHER

FLAMMABLE VAPORS AND

LIQUIDS IN THE VICINITY OF THIS

OR ANY OTHER APPLIANCE.

This appliance may be installed in an

after market permanently located

manufactured (mobile) home where not

prohibited by local codes.

This appliance is only for use with the

type of gas indicated on the rating plate.

This appliance is not convertible for use

with other gases unless a certiﬁed kit is

used.

Stardance

Natural Vent Gas Heater

Model SNV30: 3980-3996

Homeowner’s Installation

and Operating Manual

CE R TI F IE D



































7067

SDV fully assembled

cover

12/22/03

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Stardance Natural Vent Gas Heater

20007067

PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE.

Thank you and congratulations on your purchase of a Vermont Castings stove.

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these

instructions may result in a possible ﬁre hazard and will void the warranty.

Table of Contents

Installation & Operating Instructions .........................................................................................3

Stove Dimensions ...............................................................................................................4

Clearance Requirements .....................................................................................................5

Alcove Minimum Dimensions ..............................................................................................5

Hearth Requirements ..........................................................................................................5

Gas Speciﬁcations ...............................................................................................................6

Gas Inlet and Manifold Pressures .......................................................................................6

High Elevations ...................................................................................................................6

Venting Requirements .........................................................................................................6

Vent Layout and Height Requirements ................................................................................6

Passing Through a Combustible Wall or Ceiling .................................................................7

Venting Requirements .........................................................................................................7

Installation

Unpack the Stove ................................................................................................................8

Install the Optional Fan .......................................................................................................8

Venting System Assembly ...................................................................................................9

Paint Option for Enamelled Stoves ...................................................................................10

Connect the Gas Supply Line ............................................................................................10

Burner Information ............................................................................................................. 11

Install ON/OFF Switch ....................................................................................................... 11

Thermostat Connection ..................................................................................................... 11

Install the Logset ............................................................................................................... 11

Install the Front Plate ........................................................................................................12

Operation

Your First Fire ....................................................................................................................13

Pilot and Burner Inspection ...............................................................................................13

Flame & Temperature Adjustment .....................................................................................13

Flame Characteristics ........................................................................................................13

Lighting and Operating Instructions ...................................................................................14

Troubleshooting .................................................................................................................15

Fuel Conversion Instructions .............................................................................................16

Maintenance

Annual System Inspection .................................................................................................19

Logset and Burner Cleaning and Inspection .....................................................................19

Care of Cast Iron ...............................................................................................................19

Cleaning the Glass ............................................................................................................19

Glass Replacement ...........................................................................................................19

Gasket Replacement .........................................................................................................20

Inspect the Vent System Annually .....................................................................................20

Check the Gas Flame Regularly .......................................................................................20

Stove Disassembly ............................................................................................................20

Wiring Diagrams ................................................................................................................21

Replacement Parts .....................................................................................................................22

Optional Accessories ..................................................................................................................25

Warranty .......................................................................................................................................30

Energuide .....................................................................................................................................32

Stardance Natural Vent Gas Heater

20007067

The Stardance Natural Vent Room Heater, Model Nos. 3980-

3996 is a vented gas appliance listed to the ANSI standard

Z21.88b-2002 and CSA-2.33b-2002 for Vented Room Heaters,

and CSA 2.17-M91, Gas-Fired Appliances For Use at High Al

titudes.

The installation of the Stardance Natural Vent Room Heater

must conform with local codes, or in the absence of local codes,

with National Fuel Gas Code, ANSI Z223.1/NFPA 54 — latest edi-

tion and CSA B-149.1 Installation Code. (EXCEPTION: Do not

derate this appliance for altitude. Maintain the manifold pressure

at 3.5” w.c. for Natural Gas and 10” w.c. for LP gas at maximum

input.)

This appliance is only for use with the type of gas indicated on

the rating plate. This appliance is not convertible for use with other

gases unless a certiﬁed kit is used.

Installation and replacement of gas piping, gas utilization

equipment or accessories, and repair and servicing of equip-

ment shall be performed only by a qualiﬁed agency. The term

“qualiﬁed agency” means any individual, ﬁrm, corporation, or

company that either in person or through a representative is

engaged in and is responsible for (a) installation or replace-

ment of gas piping, or (b), the connection, installation, repair,

or servicing of equipment, who is experienced in such work,

familiar with all precautions required, and has complied with

all the requirements of the authority having jurisdiction.

The Stardance Natural Vent Room Heater should be

inspected before use and at least annually by a qualiﬁed

service agency. It is imperative that control compartments,

burners, and circulating air passageways of the appliance

be kept clean.

The Stardance Natural Vent Room Heater and its individual

shut-off valve must be disconnected from the gas supply piping

during any pressure testing of that system at test pressures in

excess of 1/2 psig (3.5 kPa).

The Stardance Natural Vent Room Heater must be isolated

from the gas supply piping system by closing its individual manual

shutoff valve during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig.

An accessible tap is located above the pilot/on-off knob for

checking the inlet pressure.

This appliance needs fresh air for safe operation and must be

installed so there are provisions for adequate combustion and

ventilation air.

This appliance must be properly connected to a listed 4”

(100mm) Type B venting system or to an approved masonry or

factory-built chimney system. In Canada, a complete reline of

Class A chimneys is required. This heater is equipped with a vent

safety shutoff system.

This appliance must be properly connected to a venting

system. WARNING: Operation of this heater when not con-

nected to a properly installed and maintained venting system

or tampering with the vent safety shutoff sytem can result in

carbon monoxide (CO) poisoning and possible death.

This appliance is approved for bedroom installations in the

U.S. and Canada.

This appliance may be installed in an aftermarket* manufactured

(mobile) home, where not prohibited by state or local codes.

The Stardance Natural Vent Room Heater, when installed,

must be electrically grounded in accordance with local codes or,

in the absence of local codes, with the National Electrical Code

ANSI/NFPA 70, (latest edition), or of the current Canadian Electri-

cal Code C22.1.

Due to high temperatures this appliance should be located

out of trafﬁc and away from furniture and draperies.

WARNING: This appliance is hot while in operation. Keep

children, clothing, and furniture away. Contact may cause

burns or ignition of combustible materials.

Children and adults should be alerted to the hazards of high

surface temperatures and should stay away to avoid burns or

clothing ignition. Young children should be carefully super

vised when they are in the same room as the appliance.

Clothing or other ﬂammable materials should not be placed

on or near the appliance.

Any safety screen, glass or guard removed for servicing

an appliance must be replaced prior to operating the appli-

ance.

The appliance area must be kept clear and free from com-

bustible materials, gasoline, and other ﬂammable vapors

and liquids.

The ﬂow of combustion and ventilation air must not be ob-

structed. The installation must include adequate accessibility

and clearance for servicing and proper operation.

WARNING: Do not operate the Room Heater with the glass

panel removed, cracked or broken. Replacement of the panel

should be done by a licensed or qualiﬁed service person.

Do not use this appliance if any part has been under water.

Immediately call a qualiﬁed service technician to inspect the

appliance and to replace any part of the control system and

any gas control which has been under water.

Do not burn wood, trash or any other material for which

this appliance was not designed. This appliance is designed

to burn either natural gas or propane only.

This gas appliance must not be connected to a chimney

ﬂue serving a separate solid-fuel burning appliance.

CAUTION: Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper and

dangerous operation.

Verify proper operation after servicing.

* Aftermarket: Completion of sale, nor for purpose of resale,

from the manufacturer.

General Information

Proposition 65 Warning: Fuels used in gas, woodburning

or oil ﬁred appliances, and the products of combustion of such

fuels, contain chemicals known to the State of California to

cause cancer, birth defects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

Stardance Natural Vent Gas Heater

20007067

(229mm)

Valve

Inlet

26"

(680 mm)

25"

(635 mm)

14"

(355 mm)

(76 mm)

7067

Stardance fully assembled

dimensions

12/22/03 djt

Valve Inlet

See Page 5 for Flue Collar

Centerline Dimensions.

4406

Fig. 1 Stardance dimensions.

Stardance Natural Vent Gas Heater Dimensions

Stardance Natural Vent Gas Heater

20007067

Clearance Requirements

Minimum Clearances to

Combustible Materials

Measure side clearances as shown in Figures 2

through 5 from the outer edge of the cast iron stove top.

Measure rear clearances from the outermost surface of

the sheet metal rear skirt.

The Stardance heater is approved for installation into

an alcove constructed of combustible materials to the

dimensions and clearances shown on the next page.

The same clearances apply in a standard parallel instal

lation.

Parallel Installation: Minimum Clearance

and Flue Centerline

Stove Clearances A: 5” (125mm)

B: 4” (102mm)

Pipe Centerlines C: 16” (406mm)

D: 9¹⁄₄” (235mm)

ST128b

Fig. 2 Parallel installation requirements.

ST128b

SNV flue centerline

5/11/00 djt

Corner Installation: Minimum Clearance and

Flue Centerline

ST129b

SNV

corner specs

5/25/01 djt

Stove Clearance A: 4” (102mm)

Pipe Centerline B: 17” (432mm)

ST129b

Fig. 3 Corner installation requirements.

Hearth Requirements

The Stardance Heater must be installed on rigid ﬂoor-

ing. When the heater is installed directly on any com-

bustible surface other than wood ﬂooring, a metal or

wood panel extending the full width and depth of the

unit must be used as the hearth. There are no other

hearth requirements.

WARNING:

• Always maintain required clearances

(air spaces) to nearby combustibles

to prevent ﬁre hazard. Do not ﬁll air

spaces with insulation. All venting compo

nents must maintain a 1” (25 mm) clearance to

combustible materials. Maintain a 6” (152 mm)

learance when using single wall pipe.

• The gas appliance and vent system must be

vented directly to the outside of the building

and never be attached to a chimney serving a

separate solid fuel or gas-burning appliance.

• Refer to the manufacturer’s instructions in

cluded with the venting system for complete

installation procedures.

Ceiling Clearances

ST657

Fig. 4 Minimum ceiling clearance; minimu alcove height.

72"

(1829mm)

ST657

SNV

Min. Clg Clrnc

5/25/01 djt

45"

(1140mm)

Alcove Minimum Dimensions

ST658

SNV

alcove mins.

5/25/01 djt

A: 4” (102mm)

B: 33” (838mm)

C: 5” (125mm)

ST658

Fig. 5 The Stardance Natural Vent Stove is approved for

installation into alcoves built of combustible materials.

Stardance Natural Vent Gas Heater

20007067

Venting Requirements and Options

The Stardance must be properly connected to a listed

4” (102 mm) Type B venting system or to an approved

Class A masonry or factory-built chimney system. In

Canada, a complete relining of Class A chimney sys-

tems is required.

The Stardance Natural Vent stove will accept decora-

tive 6” (152 mm) stove pipe around the Type B venting

system, for aesthetic purposes.

Complete Type B vent systems are available from a

number of manufacturers, and your dealer can usually

supply one. Pipe sections from different makers are not

interchangeable; do not mix pipe or vent sections from

different makers. Follow the vent system manufactur-

er’s instructions.

The vent system should conform to the speciﬁcations of

the National Fuel Gas Code, latest edition.

If connecting to a Class A chimney system, use 4” (102

mm) single wall or 4” Type B vent connector. Single wall

vent connector requires a minimum 6” (152 mm) clear-

ance to combustible surfaces.

Exterior chimneys may be subject to ﬂow reversal or

condensation. To lessen these conditions, enclose Type

B vents in an insulated chase, or reline exterior Class A

chimneys.

An approved pass-through device is always required,

whether the vent system passes through a wall or

a ceiling. Use a pass-through device from the same

maker who supplies the venting system.

Venting terminals shall not be recessed into a wall or

siding.

Vent Layout and Height Requirements

Venting for a Stardance can rise vertically through the

home, or can pass through an exterior wall and rise

along the outside of the home. Some codes require that

a Type B vent system rising on the outside of the home

be enclosed in a chase. Check your local codes for

requirements.

The minimum vent system height for the Stardance

Natural Vent Stove is 8’ (2.43 m), (Fig. 7) measured

from the top of the stove. To determine the minimum

height the vent system must extend through or past the

roof, refer to the 1993 edition of the National Fuel Gas

Code.

Weight: Fully assembled 350 lbs.

Inlet Minimum 5.5” w.c. 11” w.c.

Inlet Maximum 14” w.c. 14” w.c.

Manifold Pressure 3.5” w.c. 10” w.c.

Gas Inlet and Manifold Pressures

Natural LP (Propane)

Stardance Natural Vent

Certiﬁed to:

ANSI Z21.88-2005 / CSA Z2.33-2005

Vented Gas Fireplace Heaters

The installation must conform with local codes or, in

the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 - latest edition. (EXCEP-

TION: Do not derate this appliance for altitude. Main-

tain the manifold pressure at 3.5” w.c. for Natural Gas

and 10” w.c. for Propane.)

High Elevations

Input ratings are shown in BTU per hour and are

certiﬁed without deration for elevations up to

4,500 feet (1,370m) above sea level.

For elevations above 4,500 feet (1,370m) in USA,

installations must be in accordance with the

current ANSI Z223.1/NFPA 54 and/or local codes

having jurisdiction.

In Canada, please consult provincial and/or local

authorities having jurisdiction for installations at

elevations above 4,500 feet (1,370m).

WARNING: Improper installation, adjust-

ment, alteration, service or maintenance

can cause injury or property damage. Refer

to this manual for correct installation and

operational procedures. For assistance or

additional information consult a qualiﬁed

installer, service agency, or the gas supplier.

Gas Speciﬁcations

Max. Min.

Input Input

Model Fuel Gas Control BTU/h BTU/h

SNV30RN Nat Millivolt 28,000 19,000

SNV30RP Prop Millivolt 28,000 21,500

Stardance Natural Vent Gas Heater

20007067

Passing Through a

Combustible Wall or Ceiling

An approved pass-through device is always required

when a vent passes through a combustible wall or ceil-

ing. Check with the maker of the vent system for the

correct listed devices that are available. A listed pass-

through device is required whether or not the installa-

tion includes decorative pipe around the Type B venting

system. NOTE: It is essential to seal between the ceil-

ing support (sometimes called a ‘ﬁrestop spacer’) and

the decorative pipe, if installed, with a high-temperature

silicone sealant. (Fig. 6)

Complete the venting system installation according to

the manufacturer’s instructions.

ST361

Ceiling pass thru

5/11/00 djt

Joists

Ceiling

Support

Trim Col

lar

Air Space

Listed 4”

(102 mm)

B-Vent

Decorative

6” Pipe

High-tempera-

ture Silicone

Sealant

Air Space as Re-

quired by Code

ST361

Fig. 6 A ceiling pass-through, with decorative pipe around the

vent.

High-tem-

perature

Silicone

Sealant

Fig. 7 Vent termination window.

Venting Requirements

FP567

NVBR/NVBC VENTING RUNS

11/12/97

Venting Runs

A: Vertical installations up to 36 feet (12m) in

height. Up to an 18 ft. horizontal vent run can be

installed within the vent system using a

maximum of two 90-degree elbows or four

45-degree elbows.

B: Vertical installations up to 36 feet (12m) in

height. Up to a 24 ft. horizontal vent run can be

installed within the vent system using a

maximum of two 45-degree elbows.

(Ratio = 2/3, Hor./Vert.)

= Acceptable venting configuration

= Unacceptable venting configuration

NOTE: When venting staight vertical, without an

elbow, a minimum of 8 ft. vertical is required

off the top of the stove.

Horizontal Run (in feet)

Vertical Run (in feet)

(Measured from top of the unit before any elbow)

1 2 4 6 8 10 12 14 16 18 20 22 24

FP567b

Stardance Natural Vent Gas Heater

20007067

ST640

RUVSOD

snapstat

7/01

Snapstat Bracket

Snapstat Module

Pinch

Grommet to

Remove

ST670

Fig. 9 Remove the snapstat and grommet from the bracket

4. Connect snapstat leads. Disconnect the snapstat

module from the leads inside the snapstat bracket.

(Fig. 9) Bend open the snapstat bracket. Use needle

nose pliers to remove the black plastic grommet

from the bracket. Discard the bracket. Connect

the two wires to the two snapstat extension leads

located between the inner and outer shroud.

5. Position the fan assembly so the ducts slide be

tween the inner and outer shroud. The inner shroud

should engage with the two slots in the ends of the

bracket so the bracket and shroud are interlocked.

(Fig. 10) Secure the bracket with the four sheet

metal screws provided in the ﬁnish bag.

6. Install the snapstat by loosening the front screw on

the inner side of the duct. (Fig. 11) Slide the snapstat

under the head of the screw and tighten. Connect

the leads to the snapstat. Make sure the snapstat

assembly is mounted straight front to back.

7. Reattach rear shroud assembly in reverse order of

Step 2. Tighten bottom bolts to hold shroud in place.

WARNING

This appliance is equipped with a three-prong

(grounded) plug for your protection against shock

hazard and should be plugged directly into a

properly grounded three-prong receptacle. Do not

cut or remove the grounding prong from this plug.

Install the Optional Fan

If you are installing the optional convection Fan Kit

#2767 (FK26), continue here. If you are not installing a

fan kit, proceed to Venting System Assembly.

1. The fan kit includes a blower assembly and a rheo

stat assembly, connected by a cable. The blower as-

sembly mounts to the bottom rear of the stove, and

the rheostat mounts to the left side of the valve. The

assembly includes a ‘snapstat’ which automatically

turns the fan ON (or OFF) above (or below) approxi-

mately 109°F. The rheostat also provides a range

of fan speed settings from Off (which overrides the

snapstat function) to High. Unpack and inspect the

blower assembly. Conﬁrm that the fan spins freely.

2. Remove the rear shroud by loosening the two (2)

bolts at the bottom left and right side of the shroud.

Slide shroud straight up, rotate the bottom out and

away from stove and pull shroud out.

3. Attach the fan assembly to the fan bracket provided

in the log box. Use #10 sheet metal screws provided

in fan kit. Do not remove ﬁnger guard screws. (Fig.

Installation

Unpack the Stove

The Stardance is shipped fully assembled on its back.

Unpack the stove and carefully set it upright.

ST669

RUVSOD

attach fan to bracket

7/01

Snapstat

Wire

Rheostat Wire

Fan Bracket

Finger Guard

ST669

Fig. 8 Attach the fan assembly to the fan bracket.

CAUTION

Porcelain enamelled surfaces are fragile. Handle

porcelain enamelled castings tenderly. Familiarize

yourself with the assembly steps before you begin

and proceed with deliberation and care. If possible,

have assistance available.

Place enamelled castings on a soft, cushioned sur-

face until you are ready to assemble.

Avoid contact between the castings and other hard

surfaces or objects.

Stardance Natural Vent Gas Heater

20007067

ST194

attach fan to shroud

11/99

Outer

Shroud

Slot

Inner Shroud

Slot

ST194

Fig. 10 Position the fan to engage the inner shroud with the

fan bracket slots and secure with sheet metal screws.

ST347a

JUV

FK28 

rheostat install

9/21/00

Retaining Nut

Control Knob

ST347a

Fig. 12 Attach rheostat to left side of valve.

MOTOR

SNAPSTAT

ON/OFF

RHEOSTAT

WHT

BLK

GRN

BLK

POWER

ST196

FK26 fan diangram

11/99

ST196

Fig. 13 #2767 / FK26 fan wiring diagram.

Venting System Assembly

Adjust the leg levelers as needed. They should not

extend any further from the leg than necessary.

The venting collar is on the sheet metal draft hood/heat

exchanger assembly, over the ﬁrebox. Use a B-vent

adapter, from the same maker as the rest of the B-vent

components, to join the ﬁrst section of venting to the

draft hood.

The SNV30 stove includes a spill switch. Operating this

stove when not connected to a properly installed and

maintained venting system, or tampering with or discon-

necting the spill switch, can result in carbon monoxide

(CO) poisoning and possible death.

The stove includes a bracket for installing decorative 6”

(152mm) round stove pipe around the B-vent, for ap-

pearance purposes only. The decorative pipe need not

be concentric with the vent pipe.

If the installation includes decorative stove pipe around

the venting system, make a cardboard template of the

decorative pipe by tracing its circumference. Put this

template in the ﬂue recess in the stove top. Position the

template to ﬁt well against the front of the recess. (Fig.

14) Use this template to locate the bracket to hold the

decorative pipe. Depending on spacing, the bracket

may ﬁt inside the decorative pipe without interfering

with the vent system. Fasten the bracket to the draft

hood/heat exchanger assembly with a sheet metal

screw.

ST372

attach

decorator pipe

bracket

5/19/00 djt

Template

Sheet Metal Screw

Bracket

ST372

Fig. 14 Use a template to locate the bracket for decorative

pipe to surround the B-vent pipe.

ST671

attach snapstat

Snapstat

Left Air Duct

ST671

Fig. 11 Install the snapstat and connect the extension wire

terminals. View is with top removed, however, access is avail-

able through the grille opening.

NOTE: Shown without

top for clarity.

8. The rheostat control switch attaches to the left side

of the valve bracket at the front of the stove. (Fig.

12)

• Remove retaining nut from shaft of rheostat. (if

preinstalled)

• Insert the rheostat through the hole in the back

of the left side of the valve bracket, aligning the

locator pin with the smaller hole in that bracket.

• Thread the retaining nut onto the shaft of the

rheostat, tightening with a wrench. Do not over-

tighten.

• Attach the control knob to the rheostat shaft.

• Use the wire tie to secure the fan and rheostat

wire harnesses together.

9. Plug the power cord into a standard grounded 110

volt household outlet. If the fan control knob is not

turned to the OFF position, the fan will turn on when

the temperature at the snapstat reaches approxi-

mately 109°F.

1010

Stardance Natural Vent Gas Heater

20007067

Insert the B-vent adapter into the ﬂue collar and drill

1/8” (3mm) pilot holes through both the stove’s collar

and the adapter. Attach the adapter to the ﬂue collar

with sheet metal screws. (Fig. 15)

Attach the ﬁrst section of venting to the B-vent adapter.

Depending on the length of the individual venting

sections and the lengths of the decorative pipe, you

may need to slip the decorative pipe over the venting

sections before attaching upper sections to lower ones.

The sections of decorative pipe should be oriented with

their seams (if any) toward the wall; sections usually

do not need to be fastened at each joint, other than slip

sections. The decorative pipe need not be fastened to

the locating bracket on the stove. If the layout includes

a slip section, this should be the last section of pipe vis-

ible in the room at the ceiling. Refer to Page 7, Figure 6

for details on joining the decorative pipe at the ceiling.

ST373

attach

b vent adapter

5/19/00 djt

ST373

Fig. 15 Attach the B-vent adapter to the ﬂue.

ST374

attach

decorative pipe

5/19/00 djt

B-vent Pipe

Decorative

Pipe 7FSSK

Bracket

ST374

Fig. 16 Install decorative pipe over the B-vent pipe.

Paint Option for Enamelled Stoves

If you wish to match the decorative or vent pipe to the

color of the stove, paint the pipe before installation. Use

only a high-temperature paint. Paint only in a well-venti-

lated area. Mask the surroundings to prevent overspray.

Apply the paint lightly; two light coats will result in a

better ﬁnish than a single heavy coat. Let the paint dry

thoroughly before handling painted parts.

Connect the Gas Supply Line

Check the Rating Plate attached by a steel cable to the

ﬁrebox, to conﬁrm that you have the appropriate ﬁrebox

for the type of fuel to be used. The Stardance may be

converted from one gas to another using the appropri-

ate Fuel Conversion Kit listed on Page 24.

This appliance should only be connect-

ed by a qualiﬁed gas technician. Test to

conﬁrm manifold pressures as speciﬁed

below.

The Stardance Heater and its individual shutoff

valve must be disconnected from the gas supply

piping during any pressure testing of that system

at test pressures in excess of 1/2 psig (3.5 kPa).

The Stardance Heater must be isolated from the

gas supply piping system by closing its indi-

vidual manual shutoff valve during any pressure

testing of the gas supply piping system at test

pressure equal to or less than 1/2 psig.

There must be a gas shutoff between the stove

and the supply.

In order to connect Natural Gas, use a ﬁtting with

3/8” NPT nipple on the valve side and 1/2” natural

gas supply line with an input of 28,000 BTUs at

a manifold pressure of 3.5” and a minimum inlet

supply pressure of 5.5” w.c.

In order to connect Propane, use a ﬁtting with

3/8” NPT nipple on the valve side and 1/2” pro-

pane gas supply line with an input of 26,000

BTUs at a manifold pressure of 10.0” and a mini-

mum inlet supply pressure of 11.0” w.c.

In the U.S.; Gas connection should be made in ac-

cordance with current National Fuel Gas Code, ANSI

Z223.1/NFPA 54. Since some municipalities have

additional local codes, be sure to consult you local

authority.

In Canada; consult the local authority and CSA-B149.1

installation code.

Connect the gas supply and test for leaks. Use a 50/50

solution of liquid soap and water to test for leaks at gas

ﬁttings and joints. Apply water/soap solution with brush

only - do not over apply. NEVER test with an open

ﬂame. Light the pilot according to the directions on

Page 14, before going to the next step.

CAUTION

Stardance Natural Vent Gas Heater

20007067

Burner Information

The appliance must only use the gas speciﬁed on the

rating plate, unless converted using a Fuel Conversion

Kit. Refer to Page 25 for the correct Fuel Conversion Kit

for your model.

Conversion instructions are provided with each kit and

beginning on Page 16 in this manual.

In order to connect Natural Gas, use a ﬁtting with

3/8” NPT nipple on the valve side and 1/2” natural gas

supply line with an input of 28,000 BTUs at a manifold

pressure of 3.5” and a minimum inlet supply pressure of

5.5” w.c.

In order to connect Propane, use a ﬁtting with 3/8”

NPT nipple on the valve side and 1/2” propane gas

supply line with an input of 26,000 BTUs at a manifold

pressure of 10.0” and a minimum inlet supply pressure

of 11.0” w.c.

Install ON/OFF Switch

The switch assembly parts are found in the parts bag.

1. Attach switch assembly to left rear side of stove

shroud (when facing shroud) using two screws and

existing holes in shroud. (Fig. 17)

2. Run wires down back of stove, under bottom of rear

shroud to valve.

3. Attach wires to valve terminals. (Fig. 18)

ST315

attach switch assy

1/31/00 djt

Switch As-

sembly

Screws

Existing

Holes

ST315

Fig. 17 Attach switch assembly to rear shroud.

THIS APPLIANCE SHOULD BE CON-

NECTED TO THE GAS SUPPLY ONLY BY

A QUALIFIED GAS SERVICE TECHNICIAN.

FOLLOW ALL LOCAL CODES.

THERE MUST BE A GAS SHUT-OFF BE

TWEEN THE STOVE AND THE SUPPLY.

PILOT

ADJ

TPTH

ST228

attach switch

wires to valve

12/99

ST228

Fig. 18 Attach switch wires to valve.

Install the Log Set

NOTE: The bracket shipped with logs is for fan installa-

tion only.

1. Remove the logs from their packaging, and inspect

each piece for damage. DO NOT INSTALL DAM-

AGED LOGS.

2. Install the rear log centering it side to side on the

sheet metal shelf at the back of the ﬁrebox. (Fig. 19)

The log will touch both sides and the back wall of the

ﬁrebox.

3. Install the right log by engaging hole on bottom with

pin on the rear log. (Fig. 19) Then set right bottom

side on the burner so the edge of the log touches

the right side of the ﬁrebox. The right log does not

use the locator pins on the burner to stay in place.

4. Install the left log by engaging hole on bottom with

pin on rear log. (Fig. 21) Then set left bottom side

on the burner so the edge of the log touches the left

side of the ﬁrebox.

5. Loosely sprinkle the lava rocks directly on top of the

burner in front of and between the decorative grate

and the right and left logs. Use the lava rock to cover

brackets on the burner. (Fig. 20)

Thermostat

Wire / Gauge Maximum Run

18 40 feet

20 25 feet

22 16 feet

Thermostat Connection (optional)

Use only a thermostat rated for 500 - 750 millivolts.

Check the table below for the appropriate gauge

thermostat wire to use for the length of lead required in

your installation.

1. Install the wall thermostat in the desired location and

run the wires to the stove location. Terminate these

leads with 1/4” female connectors.

2. Connect the thermostat wires to the valve. (Fig. 18)

1212

Stardance Natural Vent Gas Heater

20007067

Install the Front Plate

Hold the front plate by the window bars and lift it into

position, engaging the two steel tabs on the top corners

behind the adjacent bosses in the side plates. (Fig. 21)

Then seat the Front against the sides so the tabs at the

bottom lip engage with the notches in the stove legs.

When properly installed, the bottom of the Front Plate

cannot be pulled away from the sides without also lifting

it.

This completes assembly of the Stardance stove.

LG142

Fig. 20 Completed log installation.

LG142

Stardance



Install logs 2



12/11/00 djt

Lava Rock

Fig. 19 Install the back, left and right logs.

LG141

Right

Log

LG141

Stardance

Install logs 1

12/11/00 djt

Decorative Grate

Rear Log

Left Log

ST783

SNV

Install front

11/20/03

Engage steel tabs

behind the cast

iron bosses

Bottom tabs engage

notch in the leg

ST783a

Fig. 21 Install the front plate.

Stardance Natural Vent Gas Heater

20007067

Fig. 22 To open the front doors, turn handle clockwise.

ST261

Stardance

operable doors

1/31/01

Clockwise

to Open

Counterclockwise

to Close

ST624

The Stardance is operated with the operable door front

plate in place with the doors open or closed. To open

the front doors, insert the handle into the door latch

stub and turn it to the left and up. (Fig. 22) When not in

use, the handle may be stored in the handle holder on

the right side of the rear shroud. (Fig. 23)

Operation

Your First Fire

Read these instructions carefully and familiarize

yourself with the burner controls shown in Figure 27.

Locate the pilot assembly, Figure 24. Follow the lighting

instructions on Page 14 exactly.

During the ﬁrst ﬁre, it is not unusual to smell some

odor associated with new logs, paint and metal being

heated. Odors should dissipate within an hour or so,

however, you can open a window to provide fresh air to

alleviate the condition.

Pilot and Burner Inspection

Each time you light your heater check that the pilot

ﬂame and burner ﬂame patterns are as shown in Figure

26. If ﬂame patterns are incorrect, turn the heater off.

Contact your dealer or a qualiﬁed gas technician for as-

sistance. Do not operate the heater until the pilot ﬂame

is correct.

Follow regular maintenance procedures as described

on Page 19.

ST624

handle holder

2/6/01

Handle

Holder

ST624

Fig. 23 When not in use, store handle in the handle holder.

ST477

Stardance

pilot location

10/4/00

Fig. 24 Pilot Assembly location.

ST476

Pilot As-

sembly

Flame & Temperature Adjustment

For stoves equipped with HI/LO valves, ﬂame adjust-

ment is accomplished by rotating the HI/LO adjustment

knob located near the center of the gas control valve.

(Fig. 25)

Flame Characteristics

It is important to periodically perform a visual check

of the pilot and the burner ﬂames. Compare them to

Figure 26. If any of the ﬂames appear abnormal, call a

service person.





Turn

counterclockwise

to decrease

flame height

Turn clockwise

to increase

flame height

HV102

Honeywell hi/lo knob

4/5/99 djt

Fig. 25 Flame adjustment knob for Honeywell valve.

CO105c

Pilot flame

4/10/00 djt

LG143

Fig. 26 Correct pilot and burner ﬂame pattern.

LG142

Stardance

Install logs 2

12/11/00 djt

Red Glow

CO105c

1414

Stardance Natural Vent Gas Heater

20007067

3. Open control access panel.

4. Push in gas control knob slightly and turn clock-

wise to “OFF”. Do not force.

5. Close control access panel.

1. STOP! Read the safety information above.

2. Turn off all electrical power to the ﬁreplace.

3. For MN/MP/TN/TP appliances ONLY, go on to

Step 4. For RN/RP appliances turn the On/Off

switch to “OFF” position or set thermostat to

lowest level.

4. Open control access panel.

5. Push in gas control knob slightly and turn

clockwise to “OFF”.

10. Push the control knob all the way in and hold.

Immediately light the pilot by repeatedly depress-

ing the piezo spark ignitor until a ﬂame appears.

Continue to hold the control knob in for about one

(1) minute after the pilot is lit. Release knob and it

will pop back up. Pilot should remain lit. If it goes

out, repeat steps 5 through 8.

FOR YOUR SAFETY READ BEFORE LIGHTING

• If you cannot reach your gas supplier, call the

Fire Department

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will not

push in or turn by hand, do not try to repair it, call a

qualiﬁed service technician. Applying force or any

attempted repair may result in a ﬁre or explosion.

D. Do not use this ﬁreplace if any part has been under

water. Immediately call a qualiﬁed service techni

cian to inspect the heater and to replace any part of

the control system and any gas control which has

been under water.

A. This heater has a pilot which must be lit manu-

ally. When lighting the pilot follow these instruc-

tions exactly.

B. BEFORE LIGHTING smell all around the heater

area for gas. Be sure to smell next to the ﬂoor

because some gas is heavier than air and will

settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any ﬁreplace

• Do not touch any electric switch

• Do not use any phone in your building

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

To Turn Off Gas To Heater

Lighting and Operating Instructions

1. Turn the On/Off switch to Off position or set the

thermostat to lowest setting.

2. Turn off all electric power to the ﬁreplace if

service is to be performed.

Lighting Instructions

6. Wait ﬁve (5) minutes to clear out any gas. Then

smell for gas, including near the ﬂoor. If you

smell gas, STOP! Follow “B” in the safety infor-

mation above. If you do not smell gas, go to the

next step.

7. Remove glass door before lighting pilot. (See

Glass Frame Removal section).

8. Visibly locate pilot by the main burner.

9. Turn knob on gas control counterclockwise

to “PILOT”.

• If knob does not pop up when released, stop

and immediately call your service technician or

gas supplier.

• If after several tries, the pilot will not stay lit,

turn the gas control knob to “OFF” and call your

service technician or gas supplier.

11. Replace glass door.

12. Turn gas control knob to “ON” position.

13. For RN/RP appliances turn the On/Off switch to

“ON” position or set thermostat to desired setting.

14. Turn on all electrical power to the ﬁreplace.

WARNING:If you do not follow these instructions exactly, a ﬁre or explosion

may result causing property damage, personal injury or loss of life.

Euro SIT SIT NOVA

Honeywell

PILOT

OFF

FP1067

lighting instruction

knobs

3/9/01 djt

3/8" - 1/2"

FP1068

Lighting instructions

Pilots

Stardance Natural Vent Gas Heater

20007067

A. Defective or misaligned Using a match, light [ilot. If pilot lights, turn off pilot and

electrode at the pilot push the ignitor button again. If pilot will not light, check

gap at electrode and pilot - it should be 1/8” to have a

strong spark.

B. Defective ignitor (push Push piezo ignitor button. Check for spark at electrode

button) and pilot. If there is no spark at the pilot, and electrode

wire is properly connected, replace ignitor.

A. Defective pilot generator Check pilot ﬂame. It must impinge on the thermocouple

(thermocouple) or thermopile. NOTE: This pilot burner assembly uses

both a thermocouple adn a thermopile. The thermo-

couple operates the pilot ﬂame. Tighten the thermo-

couple. The thermopile operates the main valve. (ON

and OFF) Clean and/or adjust pilot for maximum ﬂame

impingement on thermocouple and thermopile.

B. Defective automatic valve Turn valve knob to “Pilot”. Maintain ﬂow to pilot; millivolt

operator mete should read greater than 10mV. If the reading is

okay and the pilot does not stay on, replace the gas

valve. NOTE: An interrupter block (not supplied) must

be used to conduct this test.

C.Defective safety switch Check the continuity accross the safety limit switch with

the unit cold. If there is no continuity, the safety switch

needs to be replaced.

A. Remote switch or wires Check rocker switch and wires for proper connection

defective Use jumper wires across terminals at rocker switch. If

burner lights, replace rocker switch. If okay, use jumper

wires across rocker switch wires at the valve. If burner

lights, wires are faulty or connections are bad.

B. Thermopile may not gen- 1. Be sure wire connecitons from thermopile at gas

ate sufﬁcient voltage valve terminals are tight and thermopile is fully inserted

into pilot bracket.

2. One of the rocker switch wires may be grounded

Remove rocker switch wire form valve termianls. If

burner now stays lit, trace rocker switch wiring from

ground. It may be grounded to the appliance of the

gas supply line.

3. Check the thermopile with a millivolt meter. Take

reading at thermopile (“TP” and “TP/TH”) terminals of

gas valve. Should read 325 millivolts minimum while

holding valve knob depressed in PILOT position and

with rocker switch OFF. Replace faulty thermopile if

reading is below speciﬁed minimum.

C. Plugged burner oriﬁce Check burner oriﬁces for debris, and remove.

D. Defective automatic valve Turn knob to ON, place rocker switch to ON. Millivolt

operator meter should read greater than 10mV. If the reading is

okay and the burner does not light, replace the valve.

A. Pilot ﬂame may be too low Clean and/or adjust pilot ﬂame for maximum ﬂame

or high, (blowing or lifting). impingement on thermocouple and thermopile.

causing the pilot to drop out

B. Possible blockage of the Check the vent termianl for blockage.

vent terminal

Troubleshooting / Honeywell #8420 Gas Control System

NOTE: Before troubleshooting the gas control system, be sure the external gas shutoff is in the “ON” position.

WARNING: REMOVE THE GLASS PANEL BEFORE PERFORMING ANY GAS CONTROL SERVICE WORK.

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

1. Spark ignitor will

not light

2. Pilot will not stay lit

after carefully fol-

lowing the lighting

instructions

3. Pilot lights, no gas

to burner, valve

knob ON, remote

switch (rocker

switch) ON

4. Frequent pilot out-

age

1616

Stardance Natural Vent Gas Heater

20007067

Conversion Precautions

Conversion must be completed only by qualiﬁed

personnel. Before proceeding, turn control knob on

valve to OFF and turn gas supply OFF. Turn OFF any

electricity that may be going to the appliance. CAU-

TION: Allow stove to cool completely before beginning

conversion.

Conversion Procedure

1. Remove stove front. Lift stove front up and then

swing bottom out and away to disengage from the

stove body. (Page 19, Fig. 35)

2. Swing open the swiveling latches at the top left and

right corners of the glass frame. (Page 20, Fig. 36)

3. Pull the top edge of the glass and frame assembly

away from the ﬁrebox face. Place the assembly out

of the way on a ﬂat, padded surface such as a coun

ter protected by a towel.

4. Remove the logset from the ﬁrebox.

5. Remove the rear log bracket by loosening the screw

and sliding the bracket up. CAUTION: Do not re-

move the screw completely. It would be very difﬁcult

to replace. (Fig. 28)

CO100

Gas conversion

HI-LO knob

3/15/99 djt

Cap

Hi-Lo

Knob

Lift Open

Center Screw

CO100

Fig. 29 Remove center screw from Hi-Lo knob.

Fuel Conversion Instructions

WARNING! This conversion kit shall be installed

by a qualiﬁed service agency in accordance with

the manufacturer’s instructions and all applicable

codes and requirements of the authority having

jurisdiction. If the information in these instruc-

tions is not followed exactly, a ﬁre, explosion

or production of carbon monoxide may result

causing property damage, personal injury or loss

of life. The qualiﬁed service agency is respon-

sible for the proper installation of this kit. The

installation is not proper and complete until the

operation of the converted appliance is checked

as speciﬁed in the manufacturer’s instructions

supplied with the kit.

CAUTION: The gas supply shall be shut off prior

to disconnecting the electrical power, before pro-

ceeding with the conversion.

ST350

Jefferson

air shutter adj

3/20/00 djt

Remove

Screws

Rear Log Bracket

Pilot

Left & Right Log

Bracket Assembly

ST350

Fig. 28 Remove rear log bracket and left and right log

bracket assembly.

Loosen Screw

ST226

attach gas line

12/8/99 djt

PILO

Main

Gas Line

Gas Supply Inlet

ST226

Fig. 27 Attach the gas line to the left side of the valve.

6. Remove the right and left log bracket assembly by

unfastening the two screws which hold the burner in

place. (Fig. 28)

7. Hold the burner at the right hand side and lift to clear

the right burner leg. Then pull to the right to clear the

injectors on the left hand side.

8. Remove injector oriﬁces from left burner leg using

1/2” wrench. (Fig. 34)

9. Install conversion oriﬁces. (Refer to Table 2)

Valve Conversion

Honeywell Valve

1. Remove cap from Hi-Lo knob. This can be accom

plished by lifting the plastic cap off the screw. (Fig.

29)

2. Remove the screw from center of Hi-Lo knob with

small screwdriver turning counterclockwise. (Fig. 29)

3. Insert blue painted screw when converting to natural

gas and red painted screw when converting to LP.

4. Tighten screw (do not over tighten), replace cap.

SIT 820 Valve

1. Using TORX T20 bit, remove and discard the three

(3) pressure regulator mounting screws (A), pres-

sure regulator tower (B) and the spring and dia-

phragm assembly (C). (Fig. 30)

2. Insure the rubber gasket (D) is properly positioned

and install the new HI/LO pressure regulator assem-

bly to the valve using the new screws (E) supplied

with the kit. Tighten the screws securely. (Ref. torque

= 25 in/lb) (Fig. 31)

Stardance Natural Vent Gas Heater

20007067

FC107

SIT820

valve conversion

10/03

Fig. 30 Remove mounting screws, pressure regulator tower

and spring and diaphragm assembly.

FC107

FC108

SIT

regulator

conversion

10/03

FC108

Fig. 31 Replace regulator.

3. Install the enclosed conversion label (F) to the valve

body where it can easily be seen. (Fig. 31)

Pilot Oriﬁce Conversion

14. Locate pilot. (Fig. 28)

15. Replace pilot oriﬁce.

• Remove pilot hood by lifting up. (Fig. 32) NOTE:

It is not necessary to remove the pilot tube for

conversion.

• Remove pilot oriﬁce with allen wrench. (Fig. 33)

• Install the conversion oriﬁce.

• Reinstall pilot hood. Be sure to align hood with

index tab.

16. Adjust air shutter on the burner. The air shutter is

located on the bottom of the burner on the left. (Fig.

34) Loosen the two nuts holding the shutter in place.

On natural gas units, the shutter is shipped fully

closed. To convert to LP, reset the shutter as speci-

ﬁed in Table 2. (Fig. 35) On propane unit the shutter

CO105a

gas conversion

Pilot

1/28/00 djt

Pilot Hood

Pilot

Bracket

CO105a

Fig. 32 Remove pilot hood.

CO106a

DV360/580

Gas Conversion

Pilot2

1/28/00 djt

Index Tab

Snap Ring

Allen Wrench

CO106a

Fig. 33 Remove pilot oriﬁce.

is set at 1/8” or 3/8” opening depending on rating

plate serial number. To convert to natural gas, the

shutter should set to fully closed. Refasten the two

nuts. (Fig. 35)

NOTE: Be sure burner leg remains at a 90° angle to

ﬁrebox base after conversion.

ST785

SNV

air shutter

lp gas position

11/20/03 djt

3/8"

Air Shutter

(LP Position)

ST785

Fig. 34 LP air shutter settings.

ST718

SNV

air shutter

natural gas position

8/23/02 djt

Burner

Air Shutter

ST784

Fig. 35 Natural gas air shutter setting.

Rear

Injector

Air Inlet

Covered

Front Injector

Air Inlet

1818

Stardance Natural Vent Gas Heater

20007067

17. Replace burner. Slide the burner in at an angle

with left side lower than the right side. Slide the left

side onto the injectors, making sure the burner leg

remains at a 90° angle to the base. Lower the right

hand side down in to place. Make sure the burner is

as far left as possible and the injector shoulders are

inside the burner.

NOTE: It is very critical to keep the left burner leg,

which holds the injectors, at a 90° angel to the base.

(Fig. 36) This keeps the oriﬁces aligned with the

tubes inside burner. Failure to do so could affect the

ﬂame appearance and performance of the unit.

18. Place conversion label on valve.

19. Reinstall the right and left log bracket assembly.

20. Replace logs.

21. Replace glass and stove front.

22. Check manifold pressure.

23. Conversion is complete.

Fig. 36 Remove and replace injector oriﬁces.

ST353a

injector orifice

replace

3/21/00 djt

90°

Left Burner Leg

Injector Oriﬁces

ST353a

Conversion to LP Input (BTU/h) Air Shutter

Kit # Front Part # Rear Part # Minimum Maximum Setting

000-5022 #69 / .029” 30000513 #54 / .055” 20000130 21,500 28,000 3/8” Open

Conversion to Natural Gas Input (BTU/h) Air Shutter

Kit # Front Part # Rear Part # Minimum Maximum Setting

000-5021 #54 / .055” 20000130 #44 / .086” 30000334 19,000 28,000 Fully Closed

Table 2. Injector Oriﬁce Size Matrix

Stardance Natural Vent Gas Heater

20007067

Maintenance

Your Stardance Gas Heater will provide years of service

with minimal upkeep. The following procedures will help

ensure that your stove continues to function properly.

Annual System Inspection

Have the entire heater and venting system inspected

annually by a qualiﬁed gas technician. Replace any

worn or broken parts.

Logset and Burner /

Cleaning and Inspection

Cleanliness is critical to the proper function of the

heater. The logset and burner must all be kept free of

dust and unobstructed by debris. Inspect these areas

before each use and clean as necessary.

1. Turn the burner OFF and let the heater cool com

pletely before cleaning.

2. Lift the Stove Front up and then swing the bottom

out to disengage it from the heater shell. (Fig. 37)

3. Carefully remove the glass and frame assembly and

place it out of the way on a ﬂat, padded surface such

as a counter protected by a towel.

4. Carefully inspect the Logs for damage. Contact your

local dealer if any damage is evident. DO NOT OP-

ERATE THE HEATER WITH DAMAGED LOGS.

5. Use a soft bristled brush to sweep dust or debris

from the Logs, Pilot and Burner. Use care as the

logs are fragile and susceptible to damage.

6. Replace the glass panel and frame assembly.

7. Replace the Stove Front.

Care of Cast Iron

An occasional dusting with a dry rag will help keep the

painted surfaces looking new. Use high-temperature

stove paints, available through your local dealer, to

touch-up areas as needed. Clean areas to be painted

with a wire brush and be sure to cover the logs, burner

and valve assembly, glass and frame assembly. Apply

the paint sparingly; two light coats of paint will give bet-

ter results than a single heavy coat.

Clean porcelain enamel surfaces with a soft, damp

cloth. Do not use abrasive cleaning agents. If neces-

sary, use only a cleaning agent formulated especially

for use on porcelain enamel surfaces.

CAUTION

TURN THE PILOT OFF BEFORE PAINTING.

ALLOW THE HEATER TO COOL COMPLETELY

BEFORE PAINTING.

Cleaning the Glass

WARNING: Let the glass cool completely before at-

tempting to clean.

It will be necessary to clean the glass periodically. Dur-

ing start-up, condensation, which is normal, forms on

the inside of the glass and causes lint, dust and other

airborne particles to cling to the glass surface. Also,

initial paint curing may deposit a slight ﬁlm on the glass.

It is therefore recommended that the glass be cleaned

two or three times with a non-ammonia household

cleaner and warm water (we recommend gas ﬁreplace

glass cleaner). After that the glass should be cleaned

two or three times during each heating season depend-

ing on the circumstances present.

Clean glass after ﬁrst two weeks of opera

tion.

Glass Replacement

Replace glass only with CFM Corporation approved

parts. Refer to Page 22 for Replacement Parts. Refer to

Figure 38 and previous instructions for removal of the

damaged glass frame.

Fig. 37 Remove the Stove Front.

ST474d

Stardance fully assembled

Remove Front

1/04

2020

Stardance Natural Vent Gas Heater

20007067

Gasket Replacement

The Stardance Gas Heater uses a ‘tadpole’ type gasket

to seal between the glass panel and the frame. In time,

this gasket can become brittle and compressed and

should be replaced. New gasket is available from your

dealer.

Shut off the gas supply and allow the stove to cool.

Wear safety goggles and a dust mask.

1. Remove the Front, Glass Frame and Glass Panel.

(Figs. 37, 38) Remove the old gasket. Use a razor

blade, with rounded corners, to separate the glass

and gasket from the frame, and to clean the glass of

any remaining cement or bits of gasket.

2. Determine the correct length of gasket by laying it

out around the edge of the glass. Allow an extra 1

- 2” (25-51mm). Mark the spot to be cut. Use a utility

knife.

3. Starting on a long edge, remove about 6” of the pro

tective paper strip and apply the ﬂat adhesive face

of the gasket around the outside-facing edge of the

panel. Continue around the panel, applying a bout 6”

at a time and being careful to not stretch the mate-

rial. Do not overlap the gasket ends. (Fig. 39)

4. Apply a thin bead of high temperature silicone

rubber sealant along the inside corner of the glass

frame, all around the perimeter. Place the ﬂat

gasketed side of the glass panel back into the steel

frame. Pinch the rounded inside-facing gasket mate-

rial to bulk it up.

5. Replace the glass frame and front panel as previ

ously described.

Inspect the Vent System Annually

Have the vent system inspected annually by a quali-

ﬁed technician. Shut off the main gas supply before

inspecting the system. Both the inner exhaust pipe and

the outer combustion supply pipe must be checked to

conﬁrm that they are unblocked and in good condition.

Check the Gas Flame Regularly

To ensure that the stove is operating properly, check

the ﬂames periodically to conﬁrm that they match

Figure 40. The ﬂames will be blue during the ﬁrst 15-20

minutes of operation, and will gradually turn to yellow

after that.

Do not use your stove if the ﬂame pattern differs from

that shown here. Contact your Vermont Castings dealer

or a qualiﬁed technician for help.

ST179

glass gasket detail

11/99

ST179

Fig. 39 Wrap the gasket material around the outside edge of

the glass.

Stove Disassembly

If there is ever a need to remove the ﬁrebox assem-

bly from the stove shell, support the ﬁrebox with solid

stands about 6” (152mm) tall under the left and right

outer edges of the ﬁrebox base. Do not set the ﬁrebox

assembly directly on the ﬂoor; this can damage the

control valve and/or the gas lines from the valve to the

ﬁrebox.

Before removing the ﬁrebox from the shell, disconnect

the on/off switch wires from the valve. If the assembly

includes the optional fan, disconnect the fan rheostat.

If the installation includes a wall thermostat, disconnect

the thermostat leads from valve.

Disconnection and reconnection to the gas line should

only be done by a qualiﬁed gas service technician.

Upon reinstallation, the vent system must be sealed to

the ﬁrebox as shown in the installation section, Page 9.

Also be sure the logs are placed in the ﬁrebox correctly,

as shown in Page 12, Figures 19, 20.

Fig. 40 Correct ﬂame pattern.

LG143

LG142

Stardance

Install logs 2

12/1

1/00 djt

Red Glow

ST582a

Fig. 38 Release the latches to release the glass frame.

NOTE: Shown without top for clarity.

ST582a

SNV

release glass

latches

La page est en cours de chargement...

Vermont Castings Stardance SNV30RP Manuel utilisateur

Marque: Vermont Castings

Modèle: Stardance SNV30RP

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Vermont Castings Stardance SNV30RP User manual

Vermont Castings Stardance SNV30RP Manuel utilisateur

Vermont Castings Stardance SNV30RP Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents