Antlion Audio ModMic Wireless Manuel utilisateur

Marque
Antlion Audio
Modèle
ModMic Wireless
Taper
Manuel utilisateur
A
B
Surface Choice
Find a flat spot on the headphones for the 0.5” circle of adhesive. The adhesive will stick to smooth and
mesh surfaces but does not stick well to rubberized surfaces.
1. Put the headphones on to ensure the ModMic will reach the corner of your mouth from the desired
mounting point.
2. Thoroughly clean and dry the surface with the included alcohol pad.
ModMic Wireless
www.AntlionAudio.com Facebook: AntlionAudio Twitter: @AntlionAudio
Attaching & Orientation
1. Connect a to the ModMic base via the magnet.
2. Remove the protective backing from the adhesive.
3. While holding the ModMic, orient the mic boom
angle down so it points towards where your mouth
will be when using your headphones. This will reduce
the need for additional bends in the boom after
installation (see figure A).
4. Press the whole mic/clasp down onto the cleaned
spot and hold firmly for 60 seconds. On mesh or
curved surfaces, allow the adhesive to cure for 1
hour.
5. For best results the ModMic Wireless is designed to
be attached to the right side of your headphones so
the charging port is facing down (see figure B).
For more information/extra clasps/questions/feedback visit www.AntlionAudio.com Designed in Portland, Oregon.
Manufactured in China. ModMic and Antlion logo are trademarks of GTDevice LLC. U.S. and International patents
Initial Setup of your ModMic Wireless
1. Connect the USB extension to a USB port and attach the USB receiver. Place the receiver in clear line of sight
to your ModMic, ideally away from other wireless devices.
2. Power on the the ModMic Wireless by quickly pressing the button located on the ModMic Wireless Base .
The blue light will be solid. Your ModMic Wireless comes paired with your receiver out of the box.
3. Ensure the ModMic is unmuted (no red lights should be on).
4. Select the USB receiver as the default device in your microphone settings. Your ModMic Wireless is now
ready to use!
ModMic Wireless
SETUP
Charging
1. Insert the USB charging cable into any USB 2.0 or higher port.
2. Plug the USB cable into the ModMic Wireless’ micro USB port. A yellow indicator light should be blinking
slowly to indicate charging. A solid yellow light indicates full charge.
Mute and Power Off
1. To mute the ModMic while in use simply tap the power button. A red indicator light will appear on both
your ModMic and your Wireless Receiver.
2. To turn off the ModMic hold the power button for 2 seconds. When powered off and unplugged all
indicator lights will be off.
ModMic Wireless
FAQ
Does the ModMic Wireless or Receiver install any software or require any drivers?
No, the ModMic Wireless works with default system drivers and has no required software.
What if my device doesn't have the right size USB Port?
Certain devices no longer have a USB type-A port, however, most will operate properly if you purchase a converter
to the appropriate size.
What if I can't get the device to work?
Contact us at [email protected] or drop by our Discord for live help.
What bitrate settings should I use?
The ModMic uses 16-bit 48khz for recording in both modes.
Can I use my ModMic Wireless with other Bluetooth devices?
The ModMic Wireless will only work when paired with the Antlion USB Receiver.
As a result, it will not work with native Bluetooth devices like phones, speakers, cars, etc. unless those devices
use a USB and compatible operating system (Windows, Mac, Linux).
To which side of the headphones should I attach the ModMic Wireless?
The ModMic Wireless can attach to either side of the headphones, however, we recommend attaching the ModMic
to the right side of the headphones with the micro-USB port facing down to make it easier to charge while in use.
C D
Parts List
One ModMic Wireless
microphone
Two base clasps,
& two 3M adhesives
One foam
pop filter
Antlion USB
reciever
Carrying case &
Instruction manual
1. The mic is sensitive to plosive blast/wind
from your mouth, especially P’s (see figure C).
For best results position the mic completely
out of your breath stream and 1-2 inches
from your face.
2. Ensure the mic switch on the boom is
pointed towards your mouth (see figure D).
Do you need a little more help?
Here are some common troubleshooting steps that may help you out.
1. Ensure the ModMic Wireless mute is disabled. The red light should be off, if on, press the button once to
disable mute.
2. Make sure you have the ModMic Wireless selected as your default communication device in your recording
devices options.
3. If you're having quality or connection issues, try different USB ports on your your computer/device.
4. Use the USB extension cable to place the USB receiver in your line of sight.
5. If you need additional help contact us at [email protected].
Omni-directional
(selected)
Uni-directional
ModMic Wireless
Troubleshooting
Alcohol wipe
Getting the most from your ModMic Wireless
1 USB extension
& 1 Micro USB cable
State
Red (Mute)
Blue (pairing on/off)
Amber (battery/charge)
ModMic Wireless
LEDs and Pairing
How to Pair your ModMic Wireless
1. Connect the USB Receiver either directly of via
the USB extension cable (preferred).
2. Power on the the ModMic Wireless by briefly
pressing the power button.
3. If paired, the blue light on both will be solid.
4. If the blue light on either the receiver or the
ModMic is blinking slowly it means the device
is not detecting its paired counterpart.
5. To pair the devices, press and hold the buttons
for 5 seconds on both the ModMic and the
Antlion USB Receiver. The blue light will begin
blinking quickly on both devices.
6. Both devices should then blink slowly and
change to solid blue to indicate a connection.
The devices are now paired.
LED Diagram
Yellow LED
(Charging/Battery)
Blue LED
(Power/Pairing)
Red LED
(Mute)
For more information/extra clasps/questions/feedback visit www.AntlionAudio.com Designed in Portland, Oregon.
Manufactured in China. ModMic and Antlion logo are trademarks of GTDevice LLC. U.S. and International patents
Button
(Power/Mute)
Power On/Connected
Solid
Off
Off
Power Off
Muted
Solid
Unmuted
Off
Charging
Breathing
Fully Charged
Solid
Battery Low
Blinking
Pairing (Mic & Dongle)
Off
Fast Blinking
Connecting
Slow Blinking
indicates that the associated LED could either be ON or OFF, depending on its status.
Pursuant to FCC 15.21 of the FCC rules, changes not expressly approved by Antlion Audio might cause harmful interference and void the FCC authorization to operate
this product.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an output on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This product complies with FCC OET Bulletin 65 & Industry Canada’s RSS-102 radiation exposure limits set forth for an uncontrolled environment
Ce produit est conforme à la norme FCC OET Bulletin 65 et aux limites d'exposition au rayonnement RSS-102 d'Industrie Canada définies pour un environnement non
contrôlé.
This device complies with Part 15 of the FCC Rules and Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause harmful interference. and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à des règlements Innovation, Sciences et Développement économique Canada exempts de licence standard RSS (s). Son fonctionnement
est soumis aux deux conditions suivantes: (1) Ce dispositif ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y
compris les interférences pouvant entraîner un fonctionnement indésirable.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.
ModMic Wireless
FCC
Battery Legal
1. When charging, please put this product on a dried or ventilated area and keep it far away from heat sources
or explosive products.
2. Do not charge the battery if ModMic Wireless is hot to the touch. Otherwise it may damage the battery and
could be a fire hazard.
3. Please make sure that you use the original USB charging cable provided. If the battery appears swollen or
gets hot during charging please stop charging and contact [email protected].
4. A battery when not in use for a long time will lose its charge automatically. Charging or discharging too
often may reduce the life of the battery.
ModMic Wireless
Warranty
Warranty
FROM DATE OF PURCHASE, OUR ONE (1) YEAR LIMITED WARRANTY COVERS MANUFACTURING DEFECTS OF THE MODMIC AND/OR ITS ACCESSORIES.
If you experience a product defect and are within the return period of the reseller from which you purchased, please return the item to the retailer.
If you are outside their return window but within our warranty window of 1 year (or the minimum warranty required by your country from date of
purchase), we will repair or replace your ModMic for any manufacturing defects in the ModMic and/or its accessories at our discretion.
Our Warranty does not cover/is voided by the following:
1. Damage caused by accident, abuse, neglect, or misuse.
2. If you cannot supply a valid dated proof of purchase.
3. If the ModMic or USB Reciever has been disassembled.
Before returning your ModMic for repair or replacement please contact us first at [email protected] for further assistance!
After Warranty repair or replacement, your Warranty will remain in effect until either one (1) year after your original purchase date, or ninety (90)
days after repair or replacement, whichever is longer.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Antlion Audio ModMic Wireless Manuel utilisateur

Marque
Antlion Audio
Modèle
ModMic Wireless
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents