Hitachi CJ 14DSL Manuel utilisateur

Marque: Hitachi

Modèle: CJ 14DSL

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

CJ 18DSL

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires

avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un

endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool.

This manual should be stored in safe place.

Model Cordless Jig Saw

Modèle Scie sauteuse sans fil

Modelo Sierra de calar a batería

CJ 14DSL

•

CJ 18DSL

CJ14DSL

00Cover_CJ14DSL_US 08/11/7, 09:311

CONTENTS

Page

IMPORTANT SAFETY INSTRUCTIONS ............... 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 3

GENERAL POWER TOOL SAFETY WARNINGS ... 3

SPECIFIC SAFETY RULES AND SYMBOLS ......... 5

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER ...................................... 6

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER ...................................... 7

CAUTION ON LITHIUM-ION BATTERY ............... 7

FUNCTIONAL DESCRIPTION .................................... 9

NAME OF PARTS .................................................. 9

SPECIFICATIONS ................................................ 10

ASSEMBLY AND OPERATION ............................... 11

Page

APPLICATIONS ................................................... 11

REMOVAL AND INSTALLATION METHOD OF

BATTERY ...................................................... 11

CHARGING METHOD ......................................... 11

PRIOR TO OPERATION ....................................... 13

CUTTING ............................................................. 15

CONNECTING WITH CLEANER ......................... 17

CONCERNING CUTTING OF STAINLESS

STEEL PLATES ............................................. 17

SELECTION OF BLADES ..................................... 18

HOUSING THE ALLEN WRENCH ....................... 18

MAINTENANCE AND INSPECTION ....................... 20

ACCESSORIES ......................................................... 21

STANDARD ACCESSORIES ............................... 21

OPTIONAL ACCESSORIES ................................. 21

PARTS LIST .............................................................. 62

English

ÍNDICE

Español

Página

INSTRUCCIONES IMPORTANTES SOBRE

SEGURIDAD ................................................. 42

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ............................................ 42

SEGURIDAD ............................................................. 42

ADVERTENCIAS DE SEGURIDAD GENERAL

DE LA HERRAMIENTA ELÉCTRICA ............ 42

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ................................................. 44

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA EL CARGADOR DE

BATERÍAS ..................................................... 45

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA LA BATERÍA Y EL

CARGADOR DE BATERÍAS ......................... 46

ADVERTENCIA DE LA BATERÍA DE LITIO ......... 47

DESCRIPCIÓN FUNCIONAL .................................... 49

NOMENCLATURA ............................................... 49

ESPECIFICACIONES ............................................ 50

Página

MONTAJE Y OPERACIÓN ...................................... 51

APLICACIONES ................................................... 51

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 51

MÉTODO DE CARGA .......................................... 51

ANTES DE LA OPERACIÓN ................................ 53

CORTAR ............................................................... 56

CONEXION CON EL LIMPIADOR ....................... 57

SOBRE EL CORTE DE CHAPAS DE ACERO

INOXIDABLE ................................................ 58

SELECCION DE LAS CUCHILLAS ...................... 58

ALOJAMIENTO DE LA LLAVE ALLEN ............... 58

MANTENIMIENTO E INSPECCIÓN ........................ 60

ACCESORIOS ........................................................... 61

ACCESORIOS ESTÁNDAR ................................. 61

ACCESORIOS OPCIONALES .............................. 61

LISTA DE PIEZAS .................................................... 62

Page

CONSIGNES DE SÉCURITÉ IMPORTANTES ...........

SIGNIFICATION DES MOTS

D’AVERTISSEMENT .................................... 22

SECURITE ................................................................ 22

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES ........

REGLES DE SECURITE SPECIFIQUES ET

SYMBOLES .................................................. 24

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE .......... 25

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DE LA BATTERIE ET

DU CHARGEUR DE BATTERIE .................... 26

PRÉCAUTIONS RELATIVES A LA BATTERIE AU

LITHIUM ION ................................................ 27

DESCRIPTION FONCTIONNELLE ........................... 29

NOM DES PARTIES ............................................ 29

SPECIFICATIONS ................................................ 30

Français

Page

ASSEMBLAGE ET FONCTIONNEMENT ................ 31

UTILISATIONS .................................................... 31

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 31

MÉTHODE DE RECHARGE ................................. 31

AVANT L’UTILISATION ...................................... 33

COUPE ................................................................. 36

RACCORDEMENT AU NETTOYEUR .................. 37

AU SUJET DU DECOUPAGE DE PLAQUES

EN ACIER INOXYDABLE ............................. 38

CHOIX DES LAMES ............................................ 38

RANGEMENT DE LA CLÉ ALLEN ....................... 38

ENTRETIEN ET INSPECTION .................................. 40

ACCESSOIRES ......................................................... 41

ACCESSOIRES STANDARD ............................... 41

ACCESSOIRES SUR OPTION ............................. 41

LISTE DES PIECES ................................................... 62

TABLE DES MATIERES

00Cover_CJ14DSL_US 08/11/7, 09:312

English

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust of fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the influence of drugs, alcohol or

medication.

01Eng_CJ14DSL_US 08/11/7, 09:323

English

A moment of inattention while operating

power tools may result in serious personal

injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different

from those intended could result in a

hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by

the manufacturer.

A charger that is suitable for one type of

battery pack may create a risk of fire when

used with another battery pack.

b) Use power tools only with specifically

designated battery packs.

Use of any other battery packs may create a

risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts.

This will ensure that the safety of the power

tool is maintained.

01Eng_CJ14DSL_US 08/11/7, 09:324

English

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

●

Lead from lead-based paints,

●

Crystalline silica from bricks and cement and other

masonry products, and

●

Arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to filter out microscopic particles.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Use clamps or another practical way to secure and

support the workpiece to a stable platform.

Holding the work by hand or against your body

leaves it unstable and may lead to loss of control.

3. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

4. NEVER touch moving parts.

NEVER place your hands, fingers or

other body parts near the tool’s moving

parts.

5. NEVER operate without all guards in place.

NEVER operate this tool without all guards or

safety features in place and in proper working

order. If maintenance or servicing requires the

removal of a guard or safety feature, be sure to

replace the guard or safety feature before resuming

operation of the tool.

6. Use right tool.

Don’t force small tool or attachment to do the job

of a heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

7. NEVER use a power tool for applications other

than those specified.

NEVER use a power tool for applications other than

those specified in the Instruction Manual.

8. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

9. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

10. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

11. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to yourself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure

and tight.

12. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so

that air can freely flow at all times. Check for dust

build-up frequently.

13. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange

for repairs by a Hitachi authorized service center.

14. NEVER leave tool running unattended. Turn power

off.

Don’t leave tool until it comes to a complete stop.

15. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry thoroughly.

17. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

01Eng_CJ14DSL_US 08/11/7, 09:325

English

18. ALWAYS wear a mask or respirator to protect

yourself from dust or potentially harmful particles

generated during operation.

19. ALWAYS firmly grip the handle while operating.

20. ALWAYS be careful with buried object such as an

underground wiring.

Touching these active wiring or electric cable with

this tool, you may receive an electric shock.

Confirm if there are any buried object such as

electric cable within the wall, floor or ceiling where

you are going to operate here after.

21. Definitions for symbols used on this tool

V ............... volts

—

---

.............. direct current

Hz ............. hertz

A ............... amperes

no ............ no load speed

---/min ...... revolutions or reciprocation per minute

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER

WARNING:

Death or serious bodily injury could result from

improper or unsafe use of battery chargers. To avoid

these risks, follow these basic safety instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and

operating instructions for battery charger Model

UC18YRSL.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger,

(2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI

rechargeable battery type BSL1430 and BSL1830.

Other type of batteries may burst causing personal

injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold

by the battery charger manufacturer may result in

a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

7. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected

to damage or stress.

8. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in

good electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as specified in

Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

02 1818 18 16

23 1818 16 14

34 1818 16 14

* If the input rating of a battery charger is given in

watts rather than in amperes, the corresponding

ampere rating is to be determined by dividing the

wattage rating by the voltage rating–for example:

1,250 watts

125 volts

= 10 amperes

9. Do not operate battery charger with damaged cord

or plug-replace them immediately.

10. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged

in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a

qualified serviceman when service or repair is

required. Incorrect reassembly may result in a risk

of electric shock or fire.

12. To reduce risk of electric shock, unplug charger

from receptacle before attempting any

maintenance or cleaning. Removing the battery

will not reduce this risk.

01Eng_CJ14DSL_US 08/11/7, 09:326

English

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE BATTERY AND BATTERY

CHARGER

You must charge the battery before you can use the

power tool. Before using the model

UC18YRSL battery charger, be sure to read all

instructions and cautionary statements on it, the battery

and in this manual.

CAUTION:

USE ONLY HITACHI BATTERY TYPE BSL1430 AND

BSL1830. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery or battery charger can

lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is

damaged or is completely worn out. The battery

can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery

charger’s air vents. Electric shock or damage to

the battery charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is

low humidity and good ventilation.

6. NEVER charge when the temperature is below

32°F (0°C) or above 104°F (40°C).

Charging the battery at temperatures outside the

range of 32°F – 104°F (0°C – 40°C) may prevent

proper charging and reduce battery life.

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in

places where the temperature may reach or exceed

104°F (40°C).

12.

ALWAYS

operate charger on standard household

electrical power (120 volts). Using the charger on

any other voltage may overheat and damage the

charger.

13.

ALWAYS

wait at least 15 minutes between charges

to avoid overheating the charger.

14.

ALWAYS

disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor

may stop. This is not the trouble but the result of

protection function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work,

the battery power may stop.

In this case, stop using the battery and let the

battery cool. After that, you can use it again (only

BSL1830).

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on

the battery.

䡬

During work make sure that swarf and dust do not

fall on the battery.

䡬

Make sure that any swarf and dust falling on the

power tool during work do not collect on the

battery.

䡬

Do not store an unused battery in a location

exposed to swarf and dust.

䡬

Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it

together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or

subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

7. If the battery charging fails to complete even when

a specified recharging time has elapsed,

immediately stop further recharging.

8. Do not put or subject the battery to high

temperatures or high pressure such as into a

microwave oven, dryer, or high pressure container.

9. Keep away from fire immediately when leakage

or foul odor are detected.

10. Do not use in a location where strong static

electricity generates.

01Eng_CJ14DSL_US 08/11/7, 09:327

English

11. If there is battery leakage, foul odor, heat

generated, discolored or deformed, or in any way

appears abnormal during use, recharging or

storage, immediately remove it from the

equipment or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your

eyes, do not rub your eyes and wash them well

with fresh clean water such as tap water and

contact a doctor immediately.

If left untreated, the liquid may cause eye-

problems.

2. If liquid leaks onto your skin or clothes, wash well

with clean water such as tap water immediately.

There is a possibility that this can cause skin

irritation.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

3. If you find rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the first time, do not use and return

it to your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of fire. Please observe the

following matters when storing the battery.

䡬

Do not place electrically conductive cuttings, nails,

steel wire, copper wire or other wire in the storage

case.

䡬

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 1).

01Eng_CJ14DSL_US 08/11/7, 09:328

English

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ from those on your

own power tool.

NAME OF PARTS

1. Cordless Jig Saw (CJ14DSL / CJ18DSL)

䡬

Battery

Fig. 1

Lever

Blade

Switch

Base

Guide roller

Change knob

LED light

Lock off button

Battery

Latch

Ventilation holes

Terminals

Battery cover

Battery

Latch

Ventilation holes

Terminals

Battery cover

01Eng_CJ14DSL_US 08/11/7, 09:329

English

2. Battery Charger (UC18YRSL)

Fig. 2

SPECIFICATIONS

1. Cordless jig saw

Model CJ14DSL CJ18DSL

Motor DC motor

No-Load Speed 0-2,400/min

Capacity Wood 5-5/16" (135mm)

Mind steel 3/8" (10mm)

Stroke 1" (26mm)

Min. cutting radius 1" (25mm)

Model BSL1430 BSL1830

Type Lithium – ion battery

Battery

Voltage DC 14.4V DC 18V

Capacity 3.0 Ah

Weight 5.1 lbs (2.3 kg) 5.3 lbs (2.4 kg)

Pilot lamp

Cord

Nameplate

Guide rail

2. Battery Charger (UC18YRSL)

NOTE: The charging time may vary according to ambient temperature and power source voltage.

Input power source Single phase: AC 120 V 60 Hz

Charging time Approx. 45 min.

Charger

Charging voltage DC 14.4 V 18 V

Charging current DC 3.5 A

Weight 1.3 lbs. (0.6 kg)

01Eng_CJ14DSL_US 08/11/7, 09:3210

English

APPLICATIONS

䡬

Cutting various lumber and pocket cutting

䡬

Cutting mild steel plate, aluminum plate, and

copper plate

䡬

Cutting plastics, such as phenol resin and vinyl

chloride

䡬

Cutting thin and soft construction materials

䡬

Cutting stainless steel plate (With No. 97 blade)

REMOVAL AND INSTALLATION METHOD

OF BATTERY

1. Battery removal

Hold the handle tightly and push the battery latch

to remove the battery (see Fig. 3).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 3).

Fig. 3

CHARGING METHOD

NOTE:

Before plugging into the receptacle, make sure the

following points.

䡬

The power source voltage is stated on the

nameplate.

䡬

The cord is not damaged.

ASSEMBLY AND OPERATION

WARNING:

Do not charge at voltage higher than indicated on

the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals)

WARNING:

Do not use the electrical cord if

damaged. Have it repaired

immediately.

2. Insert the battery into the charger.

Firmly insert the battery into the charger until the

line is visible, as shown in Fig. 4 .

Rechargeable

battery

Charger

Pilot lamp

Fig. 4

Latch

Battery

Pull out

Insert

Push

Line

Line

01Eng_CJ14DSL_US 08/11/7, 09:3211

English

3. Charging

When the battery is connected to the battery

charger, charging will commence and the pilot

lamp will light in red. (See Table 2)

NOTE:

If the pilot lamp flikers in red, pull out the plug

from the receptacle and check if the battery is

properly mounted.

When the battery is fully charged, the pilot lamp

will blink in red slowly. (At 1-second intervals) (See

Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown

in Table 2, according to the condition of the charger

or the rechargeable battery.

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1

seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Blinks

Lights

Blinks

Flickers

Lights

Malfunction in the

battery or the charger

Battery overheated.

Unable to charge

(Charging will

commence when

battery cools).

Overheat

standby

The

pilot

lamp

lights or

blinks in

red.

The

pilot lamp

lights in

green.

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in the Table 3, and batteries that have

become hot should be cooled for a while before

being recharged.

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time (At 20°C)

NOTE:

The charging time may vary according to

temperature and power source voltage.

4. Disconnect battery charger from the receptacle.

CAUTION

●

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out

the battery from the battery charger.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its

battery. If you continue to use the tool and exhaust

the electric current, the battery may be damaged

and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately

after use. If such a battery is recharged

immediately after use, its internal chemical

substance will deteriorate, and the battery life will

be shortened. Leave the battery and recharge it

after it has cooled for a while.

Table 3 Recharging ranges of batteries

Rechargeable Temperatures at which the

batteries battery can be recharged

BSL1430, 32°F–104°F

BSL1830 (0°C–40°C)

Charger

UC18YRSL

Battery

BSL1430, BSL1830 Approx. 45 min.

01Eng_CJ14DSL_US 08/11/7, 09:3212

English

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes rest

until the next charging.

●

If the battery is rechraged when it is warm due to

battery use or exposure to sunlight, the pilot lamp

may light in green.

The battery will not be recharged. In such a case,

let the battery cool before charging.

●

When the pilot lamp flikers rapidly in red (at 0.2–

second intervals), check for and take out any

foreign objects in the charger’s battery installation

hole. If there are no foreign objects, it is probable

that the battery or charger is malfunctioning. Take

it to your authorized Service Center.

PRIOR TO OPERATION

1. Power switch

Ensure that the switch is in the OFF position.

2. Confirming condition of the environment:

Confirm that the work site is placed under

appropriate conditions conforming to prescribed

precautions.

3. Dust produced in operation

The dust produced in normal operation may affect

the operator’s health. Either of following way is

recommended.

a) Wear a dust mask

b) Use external dust collection equipment

When using the external dust collection

equipment, connect the adapter with the hose from

external dust collection equipment. (Fig. 5)

4. Changing blades

CAUTION:

●

Be sure to switch power OFF and disconnect the

battery from the body when changing blades.

●

Do not open the lever when plunger is moving.

Lever

Blade

holder

Fig. 6

Fig. 7

Blade holder

Blade

Fig. 8

Roller

Blade

Roller

Blade

Fig. 5

Base

Rear

hole

Dust

collector

Adapter

Cleaner

Hook

Notch

(1) Open the lever up to the stop. (Fig. 6-arrow I)

(2) Remove fitted blade.

(3) Insert new blade up to the stop in the blade holder.

(Fig. 6-arrow II)

(4) Close the lever. (Fig. 6-arrow III)

NOTE:

䡬

Confirm the protrusions of blade inserted to the

blade holder surely. (Fig. 7)

䡬

Confirm the blade located between the groove of

roller. (Fig. 8)

01Eng_CJ14DSL_US 08/11/7, 09:3213

English

5. Switch operation

(1) Lock-off button (Fig. 9)

The jig saw is equipped with a lock-off button. To

activate the trigger lock, move the button to the

lock position. Move the button to the free position

to operate the tool.

CAUTION:

Always lock the switch when carrying or storing

the tool eliminate unintentional starting.

(2) Trigger switch (Fig. 10)

䡬

The number of strokes of the blade can be adjusted

to within the range of 0 to 2,400 strokes/minute

depending on the amount the switch is pulled. In

addition, releasing the switch activates a break that

stops the blade immediately.

䡬

When the switch is turned on, an LED lamp lights

to illuminate the end of the blade. This lamp goes

out when the switch is released.

CAUTION:

●

Always make sure to push in the lock off button

to the locked position when not using the saw.

●

Do not look directly into the light from the LED

lamp. Continuous and direct exposure to the light

from the LED lamp can injure your eyes.

6. Adjusting the orbital operation

(1) This Jig Saw employs orbital operation which

moves the blade back and forth, as well as up and

down. Set the change knob shown in Fig. 11 to

“0” to eliminate the orbital operation (the blade

moves only up and down). The orbital operation

can be selected in 4 steps from “0” to “III”.

(2) For the hard material, such as a steel plate, etc.,

decrease the orbital operation. For the soft

material, such as lumber, plastic, etc., increase the

orbital operation to increase work efficiency. To

cut the material accurately, decrease the orbital

operation.

7. Cutting stainless steel plates

This Jig Saw can cut stainless steel plates by using

No. 97 blade. Carefully read “Concerning cutting

of stainless steel plates” for proper operation.

8. Splinter guard

Using the splinter guard when cutting wood

materials will reduce splintering of cut surfaces.

Insert the splinter guard in the space on the base,

and push it completely. (See Fig. 12)

9. Chip cover

Chip cover prevents chips from flying off and

improves the efficiency of dust collector.

Insert the chip cover between the base and lever,

and push with a slight pressure until it catches in

place. (Fig. 13)

When removing chip cover, hold both sides of knob

and slightly open until it can be removed from the

Jig Saw. (Fig. 14)

NOTE:

There is a possibility that chip cover is frosted when

cutting the metal.

Fig. 9

Lock off button

Lock

Free

Fig. 11

Change knob

Fig. 12

Splinter

guard

Base

Insert

Fig. 10

Switch

LED light

01Eng_CJ14DSL_US 08/11/7, 09:3214

English

10. Sub base (Sold separately)

Using the sub base (made from steel) will reduce

abrasion of aluminium base especially in cutting

metals.

Using the sub base (made from resin) will reduce

scratching of cut surface. Attach the sub base to

the bottom surface of base by attached 4 screws.

11. About Remaining Battery Indicator

When pressing the remaining battery indicator

switch, the remaining battery indicator lamp lights

and the battery remaining power can be checked.

(Fig.15) When releasing your finger from the

remaining battery indicator switch, the remaining

battery indicator lamp goes off. The table 5 shows

the state of remaining battery indicator lamp and

the battery remaining power.

As the remaining battery indicator shows

somewhat differently depending on ambient

temperature and battery characteristics, read it as

a reference.

Fig. 15

NOTE:

䡬

Do not give a strong shock to the switch panel or

break it.It may lead to a trouble.

䡬

To save the battery power consumption, the

remaining battery indicator lamp lights while

pressing the remaining battery indicator switch.

CUTTING

CAUTION:

on lithium-ion battery

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the causes

of overloading.

CAUTION:

䡬

In order to prevent blade dislodging, damage or

excessive wear on the Plunger, please make sure

to have surface of the base plate attached to the

work piece while sawing.

䡬

At low speed do not cut a wood with a thickness

of more than 3/8” (10 mm) or metal with a

thickness of more than 1/32” (1 mm).

1. Rectilinear cutting

When cutting on a straight line, first draw a

marking gauge line and advance the saw along

that line. Using the guide (sold separately) will

make it possible to cut accurately on a straight line.

(1) Loosen the base bolt by allen wrench attached on

base. (Fig. 16)

(2) Move the base fully forward (Fig. 17), and tighten

the base bolt again.

(3) Attach the guide by passing it through the

attachment hole on the base and tighten the M5

bolt. (Fig. 18)

(4) Set the orbital position to “0”.

Fig. 13

Chip cover

Lever

Base

Insert

Fig. 14

Chip cover

Open

State of lamp Battery Remaining Power

The battery remaining power

is enough.

The battery remaining power

is a half.

The battery remaining power

is nearly empty.

Re-charge the battery soonest

possible.

Table 5

Remaining battery

indicator lamp

Remaining battery

indicator switch

01Eng_CJ14DSL_US 08/11/7, 09:3215

English

NOTE:

To ensure accurate cutting when using the guide

(Fig. 18), always set the orbital position to “0”.

Fig. 16

Base

Base bolt

Allen wrench

Fig. 17

Base

Forward

Attachment

hole

Guide

M5 bolt

Fig. 18

2. Sawing curved lines

When sawing a small circular arc, reduce the

feeding speed of the machine. If the machine is

fed too fast, it could cause the blade to break.

Fig. 19

Guide Nail or screw

Guide hole

Fig. 20

3. Cutting a circle or a circular arc

The guide also will be helpful for circular cutting.

After attaching the guide by same way noted as

above, drive the nail or screw into the material

through the hole on the guide, then use it for an

axis when cutting. (Fig. 19)

NOTE:

Circular cutting must be done with the blade

approximately vertical to the bottom surface of the

base.

4. Cutting metallic materials

(1) Set the orbital position to “0” or “I”.

(2) Cut the material at medium speed.

(3) Always use an appropriate cutting fluid (spindle

oil, soapy water, etc.). When a liquid cutting fluid

is not available, apply grease to the back surface

of the material to be cut.

5. Pocket cutting

(1) In lumber

Aligning the blade direction with the grain of the

wood, cut step by step until a window hole is cut

in the center of the lumber. (Fig. 20)

(2) In other materials

When cutting a window hole in materials other

than lumber, initially bore a hole with a drill or

similar tool from which to start cutting.

01Eng_CJ14DSL_US 08/11/7, 09:3216

English

6. Angular cutting

The base can be swiveled to both sides by up to

45° for angular cutting. (Fig. 21)

(1) Loosen the base bolt by allen wrench attached on

base and move the base fully forward. (Fig. 16,

17)

(2) Align the scale (from 0 degrees to 45 degrees by 15-

degree increments) of the semi-circular part of the

base with the [ ] mark on the gear cover. (Fig. 22)

(3) Tighten the M5 bolt again. (Fig. 16)

(4) Set the orbital position to “0”.

NOTE:

Angular cutting can not be done when adopting

chip cover or dust collector.

(6) Insert dust collector into the rear hole of the base

until the hook catches in the notch. (Fig. 24)

(7) Press the hook to remove the dust collector.

NOTE:

Wear the dust mask additionally, if available.

CONCERNING CUTTING OF STAINLESS

STEEL PLATES

CAUTION:

In order to prevent blade dislodging, damage or

excessive wear on the Plunger, please make sure to

have surface of the base plate attached to the work

piece while sawing.

When cutting stainless steel plates, adjust the unit as

described below:

1. Adjust the speed

NOTE:

The higher the speed is, the quicker the material is

cut. But the service life of the blade will be reduced

in this case. When the speed is too low, cutting

will take longer, although the service life will be

prolonged. Make adjustments as desired.

Fig. 21

Base

Fig. 22

-mark

Semi-

circular part

CONNECTING WITH CLEANER

By connecting with cleaner (sold separately) through

dust collector (sold separately) and adapter (sold

separately), most of dust can be collected.

(1) Remove the allen wrench from the base.

(2) Move the base fully forward. (Fig. 16, 17)

(3) Attach the chip cover.

(4) Connect the dust collector with adapter. (Fig. 23)

(5) Connect the adapter with the nose of cleaner. (Fig.

23)

Fig. 24

Base

Rear

hole

Dust

collector

Adapter

Nose

Hook

Notch

Blade Thickness of material Speed

1/16” – 5/32”

No. 97

(1.5 – 2.5 mm)

Middle speed

Fig. 23

Base

Chip

cover

Dust

collector

Adapter

Nose

Cleaner

Scale

01Eng_CJ14DSL_US 08/11/7, 09:3217

English

2. Set the orbital position to “0”

NOTE:

䡬

When cutting use cutting fluid (oil base cutting

fluid) to prolong the blade’s service life.

SELECTION OF BLADES

䡬

Accessory blades

To ensure maximum operating efficiency and

results, it is very important to select the appropriate

blade best suited to the type and thickness of the

material to be cut. Three types of blades are

provided as standard accessories. The blade

number is engraved in the vicinity of the mounting

portion of each blade. Select appropriate blades

by referring to Table 6.

HOUSING THE ALLEN WRENCH

It is possible to house the allen wrench on the base.

(See Fig. 25)

Fig. 25

Base

Allen wrench

01Eng_CJ14DSL_US 08/11/7, 09:3218

English

No. 1 No. 1

No. 11 No. 12 No. 15 No. 16

No. 21 No. 22 No. 41 No. 97

(Long)

(Super Long)

Thickness of material: inch (mm)

Below Below 3/8

–

2-5/32 Below 3/8

–

2-5/32 3/16

–

1-9/16 3/8

–

2-9/16

4-1/8 (105)

5-5/16 (135)

(10 – 55) 3/4(20) (10

–

55) (5

–

40) (10

–

65)

3/16

–

1-3/16

Below 3/16

–

1-3/16 1/8

–

3/4

–

30) 3/8 (10) (5

–

30) (3

–

20)

1/8

–

15/64 Below 5/64

–

3/16

–

6) 1/8(3) (2

–

1/16

–

5/32

(1.5

–

2.5)

1/8

–

15/32 Below Below

–

12) 1/8(3) 3/16(5)

Height Height

up to up to

63/64(25

)

63/64(25)

3/16

–

3/4 Below 3/16

–

19/32 Below 3/16

–

19/32

–

20) 1/4(6) (5

–

15) 1/4(6) (5

–

15)

3/16–1-3/16

Below 3/16

–

3/4 Below 3/16

–

1-3/16 1/8

–

3/4 3/16

–

19/32

–

30) 3/8(10) (5

–

20) 3/16(5) (5

–

30) (3

–

20) (5

–

15)

3/8

–

2-5/32 1/8

–

63/64 3/16

–

63/64 1/8

–

63/64 3/8

–

2-5/32 1/8

–

1-1/2 3/16

–

63/64

(10

–

55) (3

–

25) (5

–

25) (3

–

25) (10

–

55) (3

–

40) (5

–

25)

3/8

–

2-5/32 1/8

–

63/64 3/8

–

2-5/32 1/8

–

1-1/2

(10

–

55) (3

–

25) (10

–

55) (3

–

40)

1/8

–

63/64 Below 1/8

–

63/64

–

25) 1/4(6) (3

–

25)

Below

1/4(6)

Table 6 List of appropriate blades

NOTE:

䡬

The minimum cutting radius of No. 1 (Long), No. 1 ( Super Long), No. 21, No. 22 and No. 41 blades is 3-15/16" (100 mm).

Blade

Material

quality

General lumber

Plywood

Mild steel plate

Stainless steel

plate

Aluminium

copper, brass

Aluminium sash

Phenol resin,

melamin resin, etc.

Vinyl chloride,

acryl resin, etc.

Foamed polyethyl-

ene, foamed styrol

Card board,

corrugated paper

Hardboard

Fiberboard

Material

to be cut

Lumber

Iron plate

Nonferrous

metal

Plastics

Pulp

01Eng_CJ14DSL_US 08/11/7, 09:3219

English

8. Service parts list

CAUTION:

●

Repair, modification and inspection of Hitachi

Power Tools must be carried out by a Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest

technological advancements.

Accordingly, some parts may be changed without

prior notice.

MAINTENANCE AND INSPECTION

WARNING:

Be sure to turned off the switch and pull out the battery.

1. Inspecting the blade

Continued use of a dull or damaged blade will

result in reduced cutting efficiency and may cause

overloading of the motor. Replace the blade with

a new one as soon as excessive abrasion is noted.

2. Check the Screws

Loose screws are dangerous. Regularly inspect

them and make sure they are tight.

CAUTION:

Using this power tool with loosened screws is

extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner,

for they may damage the plastics.

5. Disposal of the exhausted battery

WARNING:

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable. At

the end of it’s useful life, under various state and

local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste officials for details in

your area for recycling options or proper disposal.

6. Storage

Storing in a place below 104°F (40°C) and out of

the reach of children.

7. Service and repairs

All quality power tools will eventually require

servicing or replacement of parts because of wear

from normal use. To assure that only authorized

replacement parts will be used, all service and

repairs must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

01Eng_CJ14DSL_US 08/11/7, 09:3220

La page charge ...

Hitachi CJ 14DSL Manuel utilisateur

Marque: Hitachi

Modèle: CJ 14DSL

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

CJ 18DSL

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi CJ 14DSL User manual
español: Hitachi CJ 14DSL Manual de usuario

Documents connexes

Autres documents

Hikoki UR18DA Manuel utilisateur