Husqvarna 967144301 Mode d'emploi

360BT

2-23

24-45

46-67

KEY TO SYMBOLS

2 – English

Symbols

WARNING! The machine can be a

dangerous tool if used incorrectly or

carelessly, which can cause serious or

fatal injury to the operator or others.

Please read the operator’s manual

carefully and make sure you

understand the instructions before

using the machine.

Always wear:

• Hearing protection

• Approved eye protection

A breathing mask should be used when

there is a risk of dust.

Gloves should be worn when

necessary.

The blower can forcibly throw

objects that can bounce back.

This can result in serious eye

injuries if the recommended

safety equipment is not used.

The blower operator

must make sure that no

bystanders or animals

come nearer than 15

metres. Whenever

several operators are working in the same work area, they

should maintain a safe distance of at least 15 metres from

one another.

Keep all parts of your body away from

hot surfaces.

Air purge

Other symbols/decals on the machine refer to special

certiﬁcation requirements for certain markets.

Switch off the engine by moving the stop

switch to the STOP position before

carrying out any checks or maintenance.

Always wear protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be

worn.

Refuelling.

Choke lever in ”open position”.

Choke lever in ”closed position”.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

CONTENTS

English

–

3

Contents Note the following before

starting:

Please read the operator’s manual carefully.

This decal certiﬁes that the product has been approved in

accordance with American exhaust emissions

requirements EPA Ph III and CARB Tier III. The

Emissions Compliance Period referred to on the

Emissions Compliance label indicates the numbers of

operating hours for which the engine has been shown to

meet Federal and California emission requirements.

Husqvarna AB has a policy of continuous product

development and therefore reserves the right to modify

the design and appearance of products without prior

notice.

The machine is only designed for blowing lawns,

pathways, asphalt roads and the like.

For customer assistance, contact us at our website:

www.husqvarna.com

KEY TO SYMBOLS

Symbols ................................................................ 2

CONTENTS

Contents ............................................................... 3

Note the following before starting: ........................ 3

INTRODUCTION

Dear customer! ..................................................... 4

WHAT IS WHAT?

What is what on the blower? ................................ 5

GENERAL SAFETY PRECAUTIONS

General ................................................................. 6

SAFETY INSTRUCTIONS

Personal protective equipment ............................. 8

Machine′s safety equipment ................................. 8

Checking, maintaining and servicing the

machine′s safety equipment ................................. 9

General working instructions ................................ 10

ASSEMBLY

Assembling the blow pipe and control handle ...... 13

FUEL HANDLING

Fuel ...................................................................... 14

Fueling .................................................................. 15

STARTING AND STOPPING

Starting and stopping ........................................... 16

MAINTENANCE

General ................................................................. 17

Carburetor ............................................................ 17

Mufﬂer .................................................................. 17

Cooling system ..................................................... 17

Air intake screen ................................................... 18

Spark plug ............................................................ 18

Air ﬁlter ................................................................. 18

Shoulder strap ...................................................... 19

Maintenance schedule ......................................... 20

TECHNICAL DATA

Technical data ...................................................... 21

FEDERAL AND CALIFORNIA EMISSIONS

CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS 22

!

WARNING! Long-term exposure to noise

can result in permanent hearing

impairment. So always use approved

hearing protection.

!

WARNING! Under no circumstances may

the design of the machine be modiﬁed

without the permission of the

manufacturer. Always use genuine

accessories. Non-authorized

modiﬁcations and/or accessories can

result in serious personal injury or the

death of the operator or others.

Your warranty may not cover damage or

liability caused by the use of non-

authorized accessories or replacement

parts.

!

WARNING! A blower is a dangerous tool

if used carelessly or incorrectly and can

cause serious, even fatal injuries. It is

extremely important that you read and

understand the contents of this

Operator’s manual.

Jan. 2011

4 – English

INTRODUCTION

Dear customer!

Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,

when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production

of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-

powered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different

products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst

motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working

today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our

highest priority. We develop, manufacture and market high quality motor driven products for forestry and gardening as

well as for building and construction industry.

Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the

retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this

operator′s manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and

the second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the

borrower or buyer gets the operator′s manual, so they will also know how to properly maintain and use it.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

English – 5

WHAT IS WHAT?

1

11

5

2

25

7

26

12

13

12

17

10

6

2

4

9

15

14

16

18

20

19

21

22

23

24

What is what on the blower? 360BT

1 Frame

2 Harness

3 Engine cover

4 Fan shell

5 Air intake screen

6 Fan

7 Air ﬁlter

8 Starter handle

9 Fuel tank

10 Pad

11 Spark plug

12 Vibration damping system

13 Choke control

14 Control handle/Operating handle

15 Stop switch with throttle position setting

16 Throttle trigger

17 Handlebar (Accessory)

18 Elbow

19 Clamp

20 Flexible hose

21 Control pipe

22 Clamp

23 Intermediate pipe

24 Blower nozzle

25 Operator’s manual

26 Combination spanner

GENERAL SAFETY PRECAUTIONS

6 – English

General

Starting

• Never start the machine indoors. Exhaust fumes can

be dangerous if inhaled.

• Observe the surroundings and ensure that no people

or animals can come into contact with the blower.

• Place the machine on the ground, press the machine

body against the ground with your left hand (NOTE!

Not your foot). Now grasp the starter handle with your

right hand and then pull quickly and ﬁrmly.

Fuel safety

• Always use a fuel container with an anti-spill valve.

• Never refuel the machine while the engine is running.

Always stop the engine and let it cool for a few minutes

before refueling.

• Make sure there is plenty of ventilation when refuelling

or mixing fuel (gasoline and 2-stroke oil).

• Avoid all skin contact with fuel. Fuel is a skin irritant

and may even cause skin changes.

• Move the machine at least 10 ft (3 m) from the

refuelling point before starting it.

• Never start the machine:

- If you have spilled fuel on it. Wipe off the spillage and

allow remaining fuel to evaporate.

- If you have spilled fuel on yourself or your clothes,

change your clothes. Wash any part of your body that has

come in contact with fuel. Use soap and water.

- If the machine is leaking fuel. Check regularly for leaks

from the fuel cap and fuel lines.

IMPORTANT!

The machine is only designed for blowing lawns,

pathways, asphalt roads and the like.

Do an overall inspection of the machine before use, see

maintenance schedule.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect

your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions

under the heading ”Personal protective equipment”.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Never use a machine that is faulty. Carry out the safety

checks, maintenance and service instructions

described in this manual. Some maintenance and

service measures must be carried out by trained and

qualiﬁed specialists. See instructions under the heading

Maintenance.

All covers and guards must be ﬁtted before starting.

Ensure that the spark plug cap and ignition lead are

undamaged to avoid the risk of electric shock.

The blower operator must make sure that no bystanders

or animals come nearer than 15 metres. Whenever

several operators are working in the same work area,

they should maintain a safe distance of at least 15

metres from one another.

Never allow children to use the machine.

Never allow anyone else to use the machine without ﬁrst

ensuring that they have read and understood the

contents of the operator’s manual.

Always check for any objects that may block the air

intake screen before beginning work.

Never remove the air intake screen.

In case of emergency, release yourself from the

machine by opening the waist and chest belt and let the

machine fall backwards.

Always contact local authorities and make sure you are

following applicable directives.

Keep all parts of your body away from hot surfaces.

!

WARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants. To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants consult their physician and the

medical implant manufacturer before

operating this machine.

GENERAL SAFETY PRECAUTIONS

English

–

7

Transport and storage

• Store and transport the machine and fuel so that there

is no risk of any leakage or fumes coming into contact

with sparks or open ﬂames, for example, from

electrical machinery, electric motors, electrical relays/

switches or boilers.

• When storing and transporting fuel always use

approved containers intended for this purpose.

• When storing the machine for long periods the fuel

tank must be emptied. Contact your local gas station

to ﬁnd out where to dispose of excess fuel. Empty the

fuel tank and press the primer until all fuel has been

emptied. Remove the spark plug and drop a spoon of

2-stroke oil in the cylinder. Turn over the engine a few

times and then put the spark plug back in place.

• Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

• Secure the machine during transport.

• Store the machine in a dry, cool, well-aired and dust-

free location. Store the machine out of reach of

children.

Adjusting the harness

A correctly adjusted harness and machine signiﬁcantly

facilitates the work. Adjust the harness to give the best

working position.

Tighten the side straps so that the pressure is evenly

distributed across the shoulders.

Tighten and adjust the breast belt for the best working

position.

!

WARNING! Take care when handling fuel.

Bear in mind the risk of ﬁre, explosion

and inhaling fumes.

!

WARNING! The harness must always be

worn when working with the machine.

Failure to do so means you will be unable

to manoeuvre safely and this can result

in injury to yourself or others.

SAFETY INSTRUCTIONS

8 – English

Personal protective equipment

• Gloves should be worn when necessary.

• Wear hearing protection that provides adequate noise

reduction.

• Always wear approved eye protection. If you use a

visor then you must also wear approved protective

goggles. Approved protective goggles must comply

with standard ANSI Z87.1 in the USA or EN 166 in EU

countries. Blows from branches or objects that are

thrown can damage the eyes.

• Wear sturdy, non-slip boots.

• Always wear heavy, long pants, boots, gloves, and a

long-sleeve shirt. To reduce the risk of injury

associated with objects being drawn into rotating

parts, do not wear loose clothing, scarves, jewelry,

etc. Secure hair so it is above shoulder level.

• A breathing mask should be used when there is a risk

of dust.

• Always have a ﬁrst aid kit nearby.

Machine′s safety equipment

This section describes the machine′s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

Stop switch

Use the stop switch to switch off the engine.

Remove the ignition cable and the spark plug to carry out

inspection and maintenance.

!

WARNING! You must use approved

personal protective equipment whenever

you use the machine. Personal protective

equipment cannot eliminate the risk of

injury but it will reduce the degree of

injury if an accident does happen. Ask

your dealer for help in choosing the right

equipment. Please read the operator’s

manual carefully and make sure you

understand the instructions before using

the machine.

!

WARNING! Listen out for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

!

WARNING! Never use a machine that has

faulty safety equipment! Carry out the

inspection, maintenance and service

routines listed in this section.

SAFETY INSTRUCTIONS

English – 9

Vibration damping system

Your machine is equipped with a vibration damping

system that is designed to reduce vibration and make

operation easier.

Mufﬂer

The mufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user.

In countries that have a warm and dry climate there is a

signiﬁcant risk of ﬁre. Consequently, we have equipped

the mufﬂer with a spark arrestor screen mounted inside

the mufﬂer.

For mufﬂers it is very important that you follow the

instructions on checking, maintaining and servicing your

machine. See instructions under the heading Checking,

maintaining and servicing the machine’s safety

equipment.

Checking, maintaining and

servicing the machine′s safety

equipment

Stop switch

• Start the engine and make sure the engine stops

when you move the stop switch to the stop setting.

!

WARNING! Overexposure to vibration

can lead to circulatory damage or nerve

damage in people who have impaired

circulation. Contact your doctor if you

experience symptoms of overexposure

to vibration. Such symptoms include

numbness, loss of feeling, tingling,

pricking, pain, loss of strength, changes

in skin colour or condition. These

symptoms normally appear in the

ﬁngers, hands or wrists. The risk

increases at low temperatures.

x2

!

WARNING!

Bear in mind that: Engine exhaust fumes

contain carbon monoxide, which can

cause carbon monoxide poisoning. For

this reason you should not start or run

the machine indoors, or anywhere that is

poorly ventilated.

The exhaust fumes from the engine are

hot and may contain sparks which can

start a ﬁre. Never start the machine

indoors or near combustible material!

!

WARNING! The inside of the mufﬂer

contain chemicals that may be

carcinogenic. Avoid contact with these

elements in the event of a damaged

mufﬂer.

!

WARNING! All servicing and repair work

on the machine requires special training.

This is especially true of the machine′s

safety equipment. If your machine fails

any of the checks described below you

must contact your service agent. When

you buy any of our products we

guarantee the availability of professional

repairs and service. If the retailer who

sells your machine is not a servicing

dealer, ask him for the address of your

nearest service agent.

SAFETY INSTRUCTIONS

10 – English

Vibration damping system

• Check the vibration damping units regularly for cracks

or deformation. Replace them if damaged.

• Check that the vibration damping element is

undamaged and securely attached.

Mufﬂer

• Never use a machine that has a faulty mufﬂer.

• Regularly check that the mufﬂer is securely attached

to the machine.

• The mufﬂer on your machine is equipped with a spark

arrestor screen; this must be cleaned regularly. See

the heading Mufﬂer in the Maintenance chapter. A

blocked screen will cause the engine to overheat and

may lead to serious damage. Never use a mufﬂer with

a defective spark arrestor screen.

Air ﬁlter

Never use the leaf blower without an air ﬁlter or with a

damaged or deformed ﬁlter element as unﬁltered, dusty

air can quickly destroy the engine.

General working instructions

Show consideration to persons in your surroundings by

avoiding using the machine at unsuitable times, such as

late in the evening or early in the morning. To reduce

sound levels, limit the number of pieces of equipment

used at any one time. Read through and follow the simple

directions so that you disturb your surroundings as little as

possible.

• Use the blower with the lowest possible throttle. It is

seldom necessary to use full throttle, and many work

procedures can be done at half throttle. A lower

throttle means less noise and less dust, and it is also

easier to keep control over the rubbish collected

together/moved.

• Use a rake or a brush to release rubbish stuck to the

ground.

• Hold the opening of the blower as close to the ground

as possible. Utilise the entire length of the blow pipe

to keep the air current close to the ground.

• Clean up afterwards. Make sure that you have not

blown rubbish into someone’s garden.

• Operate power equipment only at reasonable hours,

not early in the morning or late at night when people

might be disturbed. Comply with times listed in local

ordinances.

x2

!

WARNING! Never use a machine with

faulty safety equipment. The machine’s

safety equipment must be checked and

maintained as described in this section.

If your machine fails any of these checks

contact your service agent to get it

repaired.

IMPORTANT! This section considers basic safety rules

when working with blowers. If you encounter a situation

where you are uncertain how to proceed you should ask

an expert. Contact your dealer or your service

workshop. Avoid all usage which you consider to be

beyond your capability.

!

WARNING! Be aware of your

surroundings. If anyone approaches your

work area, set the throttle control to the

lowest throttle until the person is at a

safe distance. Direct the blower away

from people, animals, play areas, open

windows and cars etc.

SAFETY INSTRUCTIONS

English – 11

Basic safety rules

• No unauthorised persons or animals may be present

in the working area, which is 15 metres.

• Allow the engine to cool before refueling.

• Keep all parts of your body away from hot surfaces.

• If the machine catches ﬁre or other emergency occurs

which forces you to release yourself from the

machine, open the harness straps and let the

machine fall backwards.

• The powerful currents of air can move objects at such

a speed that they can bounce back and cause serious

eye injuries.

• Do not direct the air jet towards people or animals.

• Stop the engine before assembling or dismantling

accessories or other parts.

• Do not use the machine in bad weather, such as

dense fog, heavy rain, strong wind, intense cold, etc.

Working in bad weather is tiring and can lead to

dangerous conditions, e.g. slippery surfaces.

• Minimise the blowing time by lightly wetting dusty

areas or using spray equipment.

• Conserve water by using power blowers instead of

hoses for many lawn and garden applications,

including areas such as gutters, screens, patios, grills,

porches and gardens.

• Make sure you can move and stand safely. Check the

area around you for possible obstacles (roots, rocks,

branches, ditches, etc.) in case you have to move

suddenly. Take great care when working on sloping

ground.

• Never put the machine down with the engine running

unless you have it in clear sight.

• Engine exhaust fumes contain carbon monoxide,

which can cause carbon monoxide poisoning. For this

reason you should not start or run the machine

indoors, or anywhere that is poorly ventilated.

• The blower must not be used while on a ladder or

scaffolding.

• CAUTION! Do not use the machine unless you are

able to call for help in the event of an accident.

Basic working techniques

• This blower is a backpack type, and is carried using a

shoulder harness while operating. It is operated and

controlled with the handle on the tube using the right

hand.

!

WARNING! Watch out for thrown objects.

Always wear eye protection. Stones,

rubbish, etc. can be thrown up into the

eyes causing blindness or serious injury.

Keep unauthorised persons at a

distance. Children, animals, onlookers

and helpers should be kept outside the

safety zone of 15 m. Stop the machine

immediately if anyone approaches.

!

WARNING! Always stop the engine

before cleaning.

SAFETY INSTRUCTIONS

12 – English

• The speed of the air jet is regulated by means of the

throttle. Select the speed best suited for respective

tasks.

You can set the throttle position using the ”stop switch”

and by doing so not need to hold your ﬁnger on the throttle

all the time you are using the blower. Full throttle is

obtained when the control is held back fully.

• Check that the air intake is not blocked, for example,

by leaves or rubbish. A clogged air intake reduces the

machine’s blowing capacity and increases the

engine’s working temperature, which can result in

engine failure. Stop the engine and remove the object.

• Be aware of the wind direction. Work with the wind to

make your work easier.

• Using the blower to move large piles is time

consuming and creates unnecessary noise.

• Keep a good balance and a ﬁrm foothold.

• When work is ﬁnished the machine should be stored

vertically.

ASSEMBLY

English – 13

Assembling the blow pipe and

control handle

• Connect the blower and control pipe with the ﬂexible

hose. Clamp both ends of the ﬂexible hose in place.

Use the accompanying hardware.

1 Flexible hose

2 Control pipe

3 Clamp

4 Clamp

NOTE!

Lubricate the pipes a little to facilitate assembly.

• Fasten the handle holder to the control pipe and

tighten the knob on the holder. Please make sure to

align the handle holder with the convex of the control

pipe.

• Use the clamp to fasten the cabling to the ﬂexible

hose.

• Connect the straight pipe and pipe end. Push the

pipes together and turn them so they lock.

Accessories

Handlebar

Disassemble the intermediate pipe. Disassemble the

knob from the holder and puch the holder on to the holder

pipe. Assemble the knob and tighten.

Assemble the intermediate pipe.

• If higher air speed is required, the round blow pipe is

replaced by the ﬂat nozzle.

3

1

4

2

FUEL HANDLING

14 – English

Fuel

CAUTION! The machine is equipped with a two-stroke

engine and must always be run using a mixture of

gasoline and two-stroke engine oil. It is important to

accurately measure the amount of oil to be mixed to

ensure that the correct mixture is obtained. When mixing

small amounts of fuel, even small inaccuracies can

drastically affect the ratio of the mixture.

Gasoline

CAUTION! Always use high grade oil mixed gasoline

(minimum 87 RON).

• This engine is certiﬁed to operate on unleaded

gasoline.

• The lowest recommended octane rating is 87. If you

run the engine on lower octane rating than 87 so-

called “knocking“ can occur. This leads to an

increased engine temperature, which can result in a

serious engine breakdown.

• When working at continuous high revs a higher octane

rating is recommended. Use good quality unleaded

gasoline.

Husqvarna alkylate fuel

Husqvarna recommends the use of Husqvarna alkylate

fuel for best performance. Husqvarna alkylate fuel is not

available in all markets.

Ethanol blended fuel, E10 may be used (max 10%

ethanol blend). Using ethanol blends higher than E10 will

create lean running condition which can cause engine

damage.

Two-stroke oil

• For best results and performance use HUSQVARNA

two-stroke oil, which is specially formulated for our

two-stroke engines. Mixture 1:50 (2%).

• If HUSQVARNA two-stroke oil is not available, you

may use another two-stroke oil of good quality that is

intended for air cooled engines. Contact your dealer

when selecting an oil.

• Never use two-stroke oil intended for water-cooled

outboard engines, sometimes referred to as outboard

oil.

• Never use oil intended for four-stroke engines.

Mixing

• Always mix the gasoline and oil in a clean container

intended for fuel.

• Always start by ﬁlling half the amount of the gasoline

to be used. Then add the entire amount of oil. Mix

(shake) the fuel mixture. Add the remaining amount of

gasoline.

• Mix (shake) the fuel mixture thoroughly before ﬁlling

the machine’s fuel tank.

• Do not mix more than one month’s supply of fuel at a

time.

• If the machine is not used for some time the fuel tank

should be emptied and cleaned.

• This engine is certiﬁed to operate on unleaded

gasoline.

!

WARNING! Always ensure there is

adequate ventilation when handling fuel.

Gasoline, litre Two-stroke oil, litre

2% (50:1)

5 0,10

10 0.42/0,20

15 0,6/0,30

20 0,40

US gallon US ﬂ. oz.

1 2 1/2

2 1/2 6 1/2

5 12 7/8

FUEL HANDLING

English – 15

Fueling

• Move the machine at least 10 ft (3 m) from the

refuelling point before starting it.

• Clean the area around the fuel cap. Contamination in

the tank can cause operating problems.

• Ensure that the fuel is well mixed by shaking the

container before ﬁlling the tank.

• Check the fuel level before each use and leave space

for the fuel to expand, because the heat from the

engine and the sun may otherwise cause the fuel to

expand and overﬂow.

!

WARNING! Taking the following

precautions, will lessen the risk of ﬁre:

Refuel in a well ventilated area. Never

fuel the machine indoors.

Do not smoke or place hot objects near

fuel.

Always shut off the engine before

refueling.

Always stop the engine and let it cool for

a few minutes before refueling.

When refuelling, open the fuel cap slowly

so that any excess pressure is released

gently.

Tighten the fuel cap carefully after

refueling.

If you have spilled fuel on it. Wipe off the

spillage and allow remaining fuel to

evaporate.

Always move the machine away from the

refueling area and source before

starting.

STARTING AND STOPPING

16 – English

Starting and stopping

Cold engine

Ignition: Set the stop switch to the start position. About

one third open.

It is not allowed to set the stop switch in full throttle

position.

Choke: Set the choke control in the choke position.

Primer bulb: Press the air purge repeatedly until fuel

begins to ﬁll the bulb. The bulb need not be completely

ﬁlled.

Warm engine

Use the same starting procedure as for a cold engine but

without setting the choke control in the choke position.

Starting

Hold the body of the machine on the ground using your

left hand (CAUTION! Not with your foot!). Grip the starter

handle, slowly pull out the cord with your right hand until

you feel some resistance (the starter pawls grip), now

quickly and powerfully pull the cord.

Never wrap the starter cord around your hand

Repeat pulling the cord until the engine starts. When the

engine starts, return choke control to run position.

CAUTION! Do not pull the starter cord all the way out and

do not let go of the starter handle when the cord is fully

extended. This can damage the machine.

NOTE!

Air is released as soon as the engine is started, even

when idling.

Set the required engine speed with the throttle control.

Allow the engine to warm for a few minutes.

1 Full throttle

2 About one third open.

3 Idle speed

4 Stop switch

Stopping

The engine is stopped by moving the stop switch to the

stop position.

!

WARNING! Always move the machine

away from the refueling area and source

before starting. Place the machine on a

ﬂat surface.

Make sure no unauthorised persons are

in the working area, otherwise there is a

risk of serious personal injury. The safety

distance is 15 meters (50 ft.).

The machine may only be started in its

complete design. If the machine is

started without all the guards ﬁtted there

is a risk of personal injuries.

(4)

(3)

(2)

(1)

(4)

(3)

(2)

(1)

MAINTENANCE

English – 17

General

Remove the ignition cable and the spark plug to carry out

inspection and maintenance. Keep all parts of your body

away from hot surfaces.

Carburetor

Adjustment of the idle speed

Before any adjustments are made, make sure that the air

ﬁlter is clean and the air ﬁlter cover is ﬁtted.

The factory idle speed setting is 2,000 rpm. Use the

adjustment screw at the upper edge of the carburettor if

the idle speed has to be adjusted.

Mufﬂer

The mufﬂer is designed to reduce the noise level and to

direct the exhaust gases away from the operator. The

exhaust gases are hot and can contain sparks, which may

cause ﬁre if directed against dry and combustible

material.

The mufﬂer is equipped with a special spark arrestor

screen. The spark arrestor screen should be cleaned

once a month. This is best done with a wire brush.

To remove the spark arrestor screen proceed as follows:

• Remove the exhaust duct (4, 5).

• Remove the spark arrester (3).

• Pull out the spark arrestor screen and clean using a

wire brush. Replace the spark arrestor screen if it is

defective.

CAUTION! Never use a machine with a defective mufﬂer.

Check regularly that the mufﬂer is complete and secured

correctly. (1), (2) Tighten the screws. 8-10Nm

Check that the spark arrester and the exhaust duct are

screwed in place correctly (5). Tighten to 2-3 Nm.

Cooling system

To keep the working temperature as low as possible the

machine is equipped with a cooling system.

The cooling system consists of:

• Cooling ﬁns on the cylinder.

• Air intake screen

Clean the cooling system with a brush once a week, more

often in demanding conditions. A dirty or blocked cooling

system results in the machine overheating which causes

damage to the piston and cylinder. Check that the nozzles

are not blocked.

3

4

5

!

WARNING! The mufﬂer gets very hot

during use and remain so for some time

after stopping. This also applies at idle

speed. Contact can result in burns to the

skin. Remember the risk of ﬁre!

1

2

MAINTENANCE

18 – English

Air intake screen

Check that the air intake is not blocked on all sides

including the underside, for example, by leaves or

rubbish. A clogged air intake reduces the machine’s

blowing capacity and increases the engine’s working

temperature, which can result in engine failure. Stop the

engine and remove the object.

Spark plug

The spark plug condition is inﬂuenced by:

• Incorrect carburetor adjustment.

• An incorrect fuel mixture (too much or incorrect type

of oil).

• A dirty air ﬁlter.

These factors cause deposits on the spark plug

electrodes, which may result in operating problems and

starting difﬁculties.

Clean the outside of the spark plug. Remove it and check

the electrode gap. Adjust the gap to 0,6-0,7 mm, or

replace the spark plug. Check that the spark plug is ﬁtted

with a suppressor.

CAUTION! Always use the recommended spark plug

type! Use of the wrong spark plug can damage the piston/

cylinder.

Air ﬁlter

The air ﬁlter must be regularly cleaned to remove dust

and dirt in order to avoid:

• Carburettor malfunctions.

• Starting problems.

• Loss of engine power.

• Unnecessary wear to engine parts

• Excessive fuel consumption.

Clean the ﬁlter every 40 hours, or more regularly if

conditions are exceptionally dusty.

Avoid contact with hot surfaces on mufﬂer, cylinder etc.

Contact can result in burns to the skin.

Cleaning the air ﬁlter

Remove the air ﬁlter cover and take out the ﬁlter. Wash it

clean in warm, soapy water.

If the machine is used in dusty conditions the air ﬁlter

should be soaked in oil. See instructions under the

heading Oiling the air ﬁlter.

An air ﬁlter that has been in use for a long time cannot be

cleaned completely. The ﬁlter must therefore be replaced

with a new one at regular intervals. A damaged air ﬁlter

must always be replaced.

• Reﬁt the air ﬁlter and air ﬁlter cover.

!

WARNING! Never use the blower if the

screen is not in place. Before use, check

that the screen is in place and

undamaged.

0,6-0,7

MAINTENANCE

English – 19

Oiling the air ﬁlter

Always use special ﬁlter oil. Filter oil contains a solvent to

make it spread evenly through the ﬁlter. You should

therefore avoid skin contact.

Put the ﬁlter in a plastic bag and pour the ﬁlter oil over it.

Knead the plastic bag to distribute the oil. Squeeze the

excess oil out of the ﬁlter inside the plastic bag and pour

off the excess before ﬁtting the ﬁlter to the machine. Never

use common engine oil. This would drain through the ﬁlter

quite quickly and collect in the bottom.

Shoulder strap

If the shoulder strap is damaged, it may break while in use

and the machine may fall causing personal injury. Follow

the instructions below to replace the shoulder strap.

1 Remove the clamp from the strap.

2 Run the end of the strap through the hanger.

3 Reﬁt the clamp to the strap.

!

WARNING! Check that the thick round

pin in the clamp is inserted in the strap. If

it is inserted incorrectly it may lead to

personal injury.

20 – English

MAINTENANCE

Maintenance schedule

Below you will ﬁnd some general maintenance instructions. If you need further information please contact your service

workshop.

IMPORTANT!

Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or

injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/

or attachments not speciﬁcally recommended by HUSQVARNA.

Maintenance

Daily

Maintenance

Weekly

maintenance

Monthly

maintenance

Clean the outside of the machine. X

Check that the throttle control functions safely. X

Check that the stop switch works correctly. X

Clean the air ﬁlter. Replace if necessary. X

Check that nuts and screws are tight. X

Check that there are no fuel leaks from the engine, tank or fuel

lines.

X

Check the fuel ﬁlter for contamination and the fuel hose for cracks

or other defects. Replace if necessary.

X

Clean or replace the spark arrestor screen on the mufﬂer (only

applies to mufﬂers without a catalytic converter).

X

Check that all sides of the air intake screen are not blocked. X

Check the starter and starter cord. X

Check that the vibration damping elements are not damaged. X

Clean the outside of the spark plug. Remove it and check the

electrode gap. Adjust the gap to 0,6-0,7 mm, or replace the spark

plug. Check that the spark plug is ﬁtted with a suppressor.

X

Clean the machine’s cooling system. X

Clean the outside of the carburettor and the space around it. X

Check all cables and connections. X

Replace the spark plug. Check that the spark plug is ﬁtted with a

suppressor.

X

Check and clean the spark arrestor screen on the mufﬂer (only

applies to mufﬂers ﬁtted with a catalytic converter).

X

Clean the fuel tank. X

La page charge ...

Husqvarna 967144301 Mode d'emploi

Husqvarna 967144301 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents