Magma C10-601T-CSA Le manuel du propriétaire

Marque: Magma

Modèle: C10-601T-CSA

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Gas Grill Models: C10-601T-CSA, C10-603T-CSA

OWNER’S MANUAL

IMPORTANT, read these instructions carefully before use. Familiarize yourself with the appliance

before connecting it to its gas container. Keep these instructions for future reference.

800

MAGMA

7:00 a.m. - 5:00 p.m.

Pacific Time Monday thru Friday

or e-mail us at

[email protected]

For questions regarding performance,

assembly, operation, parts, or returns,

contact the experts at MAGMA directly

by calling TOLL FREE

For questions regarding performance, assembly,

operation, parts, or returns, contact the experts

at MAGMA by calling (562) 627-0500

7:00 a.m. - 5:00 p.m. Pacific Time Monday thru

Friday or e-mail us at mail@MagmaProducts.com

POUR VOTRE SÉCURITÉ

Que faire si vous sentez une odeur de gaz:

1.Ne pas tenter d’allumer d’appareils.

2.Éteindre toute ﬂamme.

3.Couper l’alimentation en gaz à la source.

FOR YOUR SAFETY

If you smell gas:

1.Do not attempt to light appliance.

2.Extinguish any open ﬂame.

3.Disconnect from fuel Supply.

MONOXYDE DE CARBONE

Cet appareil peut produire du

monoxyde de carbone, un gaz

inodore.

L’utilisation de cet appareil dans

des espaces clos peut entraîner

la mort.

Ne jamais utiliser cet appareil

dans un espace clos comme un

véhicule de camping, une tente,

une automobile ou une maison.

CARBON MONOXIDE HAZARD

This appliance can produce

carbon monoxide which has no

odor.

Using it in an enclosed space

can kill you.

Never use this appliance in

an enclosed space such as a

camper, tent, car or home.

POUR VOTRE SÉCURITÉ

Ne pas entreposer ni utiliser d’essence ni

d’autres vapeurs ou liquides inﬂammables à

appareil.

FOR YOUR SAFETY

Do not store or use gasoline or other liquids

with ﬂammable vapours in the vicinity of

this or any other appliance

DANGERDANGER

• USE OUTDOORS ONLY.

• DO NOT USE THIS APPLIANCE INSIDE ANY ENCLOSED SPACE.

• GRILLS RADIATE HEAT. CLEARANCE FROM COMBUSTIBLES, 24” SIDES AND BACK. NEVER USE UNDER AWNINGS,

PATIO COVERS, ETC.

• USE PROPANE GAS ONLY. FUEL STORAGE SHOULD BE IN COMPLIANCE WITH THE NATIONAL FIRE PROTECTION

ASSOCIATION (NFPA) STANDARD 58 LIQUID PETROLEUM GAS CODE AND OCCUPATIONAL HEALTH AND SAFETY

ADMINISTRATION (OSHA) STANDARD 29 CFR 1910.101

• FOR NATURAL GAS APPLICATION CONTACT MAGMA.

• ALWAYS LIGHT GRILL WITH LID OPEN.

• NEVER LEAVE HOT GRILL UNATTENDED.

• DO NOT OVERHEAT GRILL, SEE OPERATING INSTRUCTIONS

• ALWAYS TURN GRILL OFF AFTER USE.

• USE GLOVE OR HOT PAD WHEN HANDLING HOT GRILL.

• NEVER LEAVE GAS CYLINDERS AND REGULATOR CONNECTED WHEN Stored.

• STORE GAS CYLINDERS IN A SECURE WELL VENTILATED AREA, OFF OF THE GROUND, ON A NON-

COMBUSTIBLE BASE.

• DO NOT STORE GAS CYLINDERS INDOORS, IN DIRECT SUNLIGHT, BELOW DECKS ON BOATS, OR IN LOCKERS

NOT APPROVED FOR BUTANE OR PROPANE STORAGE.

• CAUTION: CHECK FOR GAS LEAKS EACH TIME CYLINDER IS CHANGED.

• NEVER CHECK FOR GAS LEAKS WITH A FLAME!

• DO NOT BLOCK, RESTRICT, OR OTHERWISE OBSTRUCT COMBUSTION OR VENTILATION AIR OPENINGS.

• DO NOT MODIFY THIS APPLIANCE.

• KEEP AREA CLEAR AND FREE FROM COMBUSTIBLE MATERIALS, GASOLINE, AND OTHER

FLAMMABLE VAPOURS AND LIQUIDS.

• CHECK THAT VALVE SEALING WASHER (A) IS IN PLACE AND IN GOOD CONDITION BEFORE

CONNECTING THE GAS CONTAINER.

• INSTALL CANISTERS IN WELL VENTILLATED AREA AND AWAY FROM OPEN FLAME, HEAT

SOURCE OR SPARKS. KEEP AWAY FROM OTHER PEOPLE OR FLAMMABLE MATERIALS.

IMPORTANT SAFETY WARNINGS

READ ALL INSTRUCTIONS BEFORE OPERATING.

Each Magma

Gas Grill is individually fire tested before it leaves the factory.

For this reason, the burner on your grill may be slightly discolored.

INSTALLATION INSTRUCTIONS

See Magma website

for replacement part numbers

and valve applications.

www.MagmaProducts.com

MOUNT HARDWARE

Fasteners are supplied for Single Mount

mounting option. See Magma Website for

mount selection.

Carriage bolt,

washer & lock nut

Single mount through-bolt applications

4 Carriage bolts, washers & lock nuts.

Note: Place washers on carriage bolts as shown above.

Burner

Lid Lock

Lid

Handle

Grill Grates

Radiant Plate

Outer Shell

Match Light Hole

Mount Support Pad

with Folding Legs

Valve Chamber

Electronic

Ignition

Slide Out Grease Tray

Control Valve

Regulator Type1

Low-Output

Thermometer

CONTROL VALVE REGULATOR

•Uses standard 1-lb. disposable propane canisters (DOT-39 NRC).

•Prior to installing valve, become familiar with the valve function and graphics

on valve knob. Never force the knob. Always turn or push gently.

•Turn control valve to “lock” and install gas canister being careful not to cross

the threads. Check for leaks prior to use, by brushing soapy water solution

around threads and orifice hole checking for bubbles.

•Position valve with gas bottle as shown (A). Gently insert valve stem into

valve chamber. Rotate until valve stem key aligns with lock detent allowing

valve to fully insert. Rotate gas canister down, so knob faces you (B) or

straight up (C) depending on application.

Indicator

Off

Medium

Lock

Unlock

High

Low

(A)

(B)

(C)

Valve will feel loose and will rotate easily. Even though the valve feels loose, it will not leak. The

valve was designed to be loose fitting in order to allow safe, easy installation and removal of

the propane canister and so it easily swings without resistance to fit all applications.

OPERATING PROCEDURES

OPERATE ONLY ON “LOW” WHEN LID IS CLOSED.

ALWAYS OPERATE WITH GREASE TRAY IN PLACE.

WARNING: Do not overheat grill.

Magma Grills do not require pre-heating. Stainless Steel loses

anti-corrosive characteristics when subjected to extreme heat. Most grilling is done on low

temperature with the lid closed. If medium or high heat is required, grill with lid open.

LIGHTING INSTRUCTIONS

• Open lid during lighting.

• Depress knob and rotate counter-clockwise to the “HIGH” flame position.

• Push Electronic Igniter. • Visually confirm ignition. • Turn knob to adjust flame.

• If grill does not light (see page 5).

•

If electronic ignition fails to ignite the gas, see MATCH LIGHTING INSTRUCTIONS.

NOTE: Before lighting, lid lock must be positioned not to engage. Open lid and turn lock to

locked position.

NOTE: Electronic ignition comes equipped with battery preinstalled. Replace with “AAA”

alkaline battery only.

MATCH LIGHTING INSTRUCTIONS

(Back up system allows use of grill until ignition system is repaired.)

• Open lid during lighting. • Place flame up to burner through the match light hole.

• Depress valve and turn counter-clockwise to the “HIGH” flame position.

• Visually confirm ignition.

TO REDUCE FLARE-UP

• Empty and clean grease tray prior to each use.

• Trim excess fats from meat. • Use non-oil based marinades.

• Reduce heat. • Use water spray directly on flare-ups.

FOLDING LEGS

For storage, transport or while using mounting option. Fold up back legs first, then front legs (as

shown). If legs become loose they can be tightened with a 5/32” Hex Key Wrench.

PRACTICAL HINTS:

Before lighting your grill, be sure that …

•

Grill is secure and properly mounted.

•

Internal components and grease tray are clean and correctly positioned.

•

You have plenty of gas in the canister.

•

Gas canister is attached properly and there are no gas leaks.

•

Lid lock has been set not to engage.

•

You have a water spray bottle handy to cool a hot grill or stop any flare-ups.

STOWING TIPS

• Always disconnect the fuel canister from the valve prior to stowing.

• Stow the valve in a clean, dry area to protect from corrosion to valve.

•

Always store propane in a sealed propane storage locker that allows leakage to vent

or use Magma Propane / Butane Storage Locker / Tote Bag.

Indicator

Off

Medium

Lock

Unlock

High

Low

Indicator

Off

Medium

Lock

Unlock

High

Low

ELECTRODE SPARK ADJUSTMENT

CAUTION: Spark can cause small shock. Do not leave

fingers on or near electrode wire while engaging igniter.

• Electrode wire should be

approximately 1/8” from gas

exit hole in burner

. Carefully adjust wire if required.

DISASSEMBLY & RE-ASSEMBLY

• Remove radiant plate’s retainer pin (see B) and remove radiant plate by sliding it out

of securing tabs (see E).

• Remove burner retainer pin (see C), remove burner. Inspect burner, remove obstructions.

CAUTION: WHEN REPLACING BURNER, CUT SLOTS IN BURNER MUST FACE DOWN.

• Remove lid by removing hinge screws and nuts with 3/16” hex key wrench

(supplied) and 1/2” wrench or pliers. CAUTION LOCK NUTS MUST BE INSTALLED WITH

LOCKING INDENT MARKS SHOWING (see F). IMPROPER INSTALLATION WILL DAMAGE

HINGE SCREWS AND LOCK NUT.

• Clean as indicated in Maintenance (page 6).

• To disconnect or replace igniters ceramic electrode. First remove two screws on valve

chamber (see D) and remove cover plate. Gently pull wire off connector (see D).

Remove electrode screw and nut with a small Phillips head screwdriver and 1/4”

wrench or pliers. Gently pull electrode with wire out of grill body inspect for damage,

replace if necessary.

• To re-assemble, reverse above procedure.

Electrode

Disconnect

wire

Screws

Battery

Locking

Indents

Retainer Pin Retainer Pin

Radiant Plate

Securing Tabs

Burner

MAINTENANCE

USING GRILL WITH LPG (PROPANE) SYSTEMS

Stainless steel contrary to popular belief can rust. Most commonly, deposits on surface of the product will trap moisture. It is

this moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel to form a protective layer of

chrome oxide. Robbed of oxygen, this reaction does not take place and “crevice corrosion” or “surface rusting” occurs. To

minimize this effect, thoroughly clean your grill with soap and water, rinse with fresh water, and dry. Avoid using stainless steel

polishes on grill exterior as most leave a residue that may discolor when grill is heated.

Additionally, stainless steel that is exposed to high heat will change color and texture over time. The “amber” color of grill

exterior and internal components is not a failure of the stainless steel and will not affect products operation. When this happens,

we recommend using “Magma Magic” Grill Restorer to remove the “amber” color and return grill to its original luster.

However, prolonged exposure to extreme high heat will cause chromium and nickel to “burn out” of stainless steel. At this point

stainless steel will become more susceptible to corrosion and will start to deteriorate. We recommended replacement of internal

components as they become seriously deteriorated.

We recommend thoroughly cleaning grill and internal components after each outing. Disassemble interior components and

remove all food residue. Use a “Scotch Brite” pad or similar product and “Easy-Off” oven cleaner for cleaning grills interior

components, followed by thoroughly washing with soap and water, rinse with fresh water & dry. AVOID CONTACT OF OVEN

CLEANER WITH SKIN, CONTROL VALVE, IGNITOR ELECTRODE & WIRE. CAUTION: DO NOT USE ANY TYPE OF ABRASIVE PAD ON

EXTERIOR MIRROR FINISH AS IT WILL SCRATCH SURFACE, USE ONLY A SOFT CLOTH. We recommend covering grill between uses.

Grill covers are available at Magma retailers or directly from Magma. See our website: magmaproducts.com After cooking Do

Not turn grill to high heat to burn off grilling residue. The grill is not a self cleaning oven & this extreme heat can damage

stainless steel components.

Grill Grates - Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for burnt-on residue. Wash with

soapy water and dry prior to storage.

Ceramic Electrode - Located just beside the burner, it should be kept clean of grease and debris. Be careful not to damage the

ceramic insulation or the wire. See page 5 for electrode spark adjustment.

Control Valve - All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in any way.

Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris obstructing the orifice.

Repair/Replacement Parts - All replacement parts are readily available at your Magma Retailers or directly from Magma.

For a complete list of replacement parts visit our website MagmaProducts.com.

• Magma LPG (Propane) Valves & Hose Kits allow Magma

Grills to be installed within existing, pre-regulated low

pressure LPG (Propane) system.

• Use only Magma Type 3 Low Pressure LPG (Propane)

Valves. See our Valve Application Guide at

MagmaProducts.com for correct valve.

• In North America use Magma A10-225 LPG 10' Gas

Grill Connection Kit in conjunction with Type 3 Valve.

Outside North America check

your local dealer for proper hose and fittings.

• A primary shutoff valve (supplied with Gas Grill

Connection Kit) must be used with this control valve at

point of connection into your system. This allows shut off

of gas supply to hose leading to grill.

• In Australia & New Zealand LPG fuel systems must

be installed by a certified

gas technician.

Gourmet

Gas Grill

Align valve stem key

to valve chamber

lock detent and rotate

Gourmet

Gas Grill

Propane (LPG)

Gas Regulator

A10-225 LPG (Propane)

10' Gas Grill Connection Kit

To other LPG

appliance

or use cap

Shut off

valve

Cylinder Valve

Gauge

Gourmet

Gas Grill

Gourmet

Gas Grill

Type 3

Valve

Type 3

Valve

Solenoid

Typical Pre-Regulated

LPG Application

Gourmet

Gas Grill

Align valve stem key

to valve chamber

lock detent and rotate

Gourmet

Gas Grill

Propane (LPG)

Gas Regulator

A10-225 LPG (Propane)

10' Gas Grill Connection Kit

To other LPG

appliance

or use cap

Shut off

valve

Cylinder Valve

Gauge

Gourmet

Gas Grill

Gourmet

Gas Grill

Type 3

Valve

Type 3

Valve

Solenoid

Typical Marine &

R.V. Application

USING GRILL WITH CNG (NATURAL GAS) SYSTEMS

• Magma on-board CNG (natural gas) valves allow Magma grills to be installed to an existing on-board, pre-regulated low

pressure CNG (natural gas) system.

• Use only Magma Type 4 Low Pressure CNG (natural gas) control valves. Visit out website at MagmaProducts.com to view

valve application guide. See your local dealer for proper hose and fittings.

Problem

Electrode covered with grease or residue

Igniter/electrode too far from burner

Electrode wire loose, disconnected, or corroded

Wire is shorted causing spark from wire before

electrode

No spark being generated

No gas flow

Obstructed gas flow

Excessive cooking temperature

Grease and/or residue build-up

Excessive fat in meats

Excessive oils in marinades

Obstructed gas flow

Flame too low

Wind directly on burner

Obstructed gas flow

Grill not level

Grease or residue build-up

Excessive fat in meats

Excessive oil in marinades

Clean electrode

Adjust electrode until proper spark appears

(see page 5)

Clean, adjust & reconnect wire between igniter

& electrode, see Complete Disassembly (page 5)

Replace Igniter, Electrode & Wire

See website for part number

Adjust electrode until proper spark appears.

Unscrew igniter push button, remove/inspect

“AAA” battery, replace “AAA” alkaline battery if

necessary, reinstall & re-assemble push button

Replace Igniter, Electrode & Wire

See website for part number

Check fuel level, replace canister or

refill cylinder

Clean burner and valve orifice.

Remove debris/spider webs

Operate only on low when lid is closed

Reduce flame level

Leave lid open

Use water spray to cool

Clean components

Trim fat from cuts of meat before grilling

Use non-oil based marinades

Clean burner and valve orifice.

Remove debris/spider webs

Increase flame

Block wind when opening lid

Clean burner and valve orifice.

Remove debris/spider webs

Level Grill

Clean components

Trim fat from cuts of meat before grilling

Use non-oil based marinades

Hot Spots

Blow-out

Yellow sooty

flame

Flare-up

Burner will

not light even

with match

Burner will

not light with

igniter

TROUBLE SHOOTING GUIDE

Possible Solution

Possible Cause

LIMITED WARRANTY

Magma Products, Inc. guarantees this product to be free from defects in materials or workmanship to the original consumer. This guarantee is for the

periods herein speciﬁed when used under normal and reasonable conditions, one (l) year from the date of original purchase. This warranty does not include

the cost of property damage or any inconvenience due to the failure of the product. Nor does it cover damage due to misuse, abuse, accident, or damage

resulting from transportation of the product. Nor does it include damage resulting from the commercial use of this product. Nor does it include, on stainless

steel products, "Surface Rust'; Excessive Corrosion due to exposure to salt water; or Discoloration or Corrosion caused by exposure to excessive heat or failure

to properly clean and care for the stainless steel surfaces. If the product fails to operate due to a defect in materials or workmanship during the warranty

period, the defective part will be repaired or replaced at Magma's option. If you wish to obtain performance under this limited warranty, you should contact

Magma's Customer Service Department via telephone at (562) 627-0500, or via e-mail at [email protected], or via U.S. Postal Service mail at "Magma

Products, Inc., Attention Customer Service, 3940 Pixie Ave. Lakewood, CA, 90712". The defective part, along with proof of purchase, must be returned post-

age prepaid to Magma Products, Inc. We suggest that you keep your purchase receipt as we may require reasonable proof of purchase.

In the state of California only, if reﬁnishing or replacement of the product is not commercially practicable, the retailer selling the product, or Magma

Products, Inc., will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer prior to the discovery

of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment from which it was purchased or to any

retail establishment selling this product in order to obtain performance under this warranty. All implied warranties, including the implied warranties of mer-

chantability and ﬁtness for a particular purpose, are limited in duration to the express warranty periods speciﬁed herein for the parts described herein. Some

states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither Magma dealers, nor the retail

establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above.

Magma's maximum liability shall not exceed the purchase price of the product paid by the original consumer. Some states do not allow the exclusion or limita-

tion of incidental or consequential damages, so the above limitation orexclusions may not apply to you. The warranty gives you speciﬁc legal rights and you

may also have other rights which vary from state to state.

MAGMA and the Magma logo are registered trademarks of Magma Products, Inc. • Newport is a trademark of Magma Products, Inc. • Patent pending.

Magma Products, Inc.

3940 Pixie Avenue, Lakewood, CA 90712 • USA

Phone (562) 627-0500 • e-mail: mail@MagmaProducts.com

MagmaProducts.com

83-600T-CSA 0217

CALIFORNIA PROPOSITION 65 – WARNING – The burning of gas cooking fuel generates some by-products, which are on the list of substances, which

are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of potential exposure to

such substances. To minimize exposure to these substances, always operate this unit according to the use and care manual, ensuring you provide good

ventilation when cooking with gas.

CONTENTS

Contents

x 4 x 4

A) (1) 3/16” Hex key wrench for lid removel.

B) Pack of (4) 1/4”-20 x 5/8” carriage bolts and lock nuts

for dual mount and single mount applications.