Thermador PRL486EDPG-01 Guide d'installation

Marque: Thermador

Modèle: PRL486EDPG-01

Catégorie: Fours

Taper: Guide d'installation

Ce manuel convient également à

For Thermador ProfessionaP PRO-GRAN DTM

Gas Ranges

Pour toutes cuisinieres a gaz Thermador Professional ®

PRO-GRAND TM

A= _>J=,=ic==3=, =..

ModeLs

PG30

PG36

PG48

Please Read Entire Instructions

Before Proceeding

mMPORTANT:

mNSTALLER:

OWNER:

Save these instructions for the Local Gas Inspector's use.

Please leave these Installation Instructions with this unit for the owner.

Please retain these instructions for future reference.

Disconnect power before installing. Before

turning power ON, be sure that all controls

are in the OFF position.

IMPORTANT

LocaJ codes vary. Installation, gas

connections and grounding must

comply with all applicable codes.

For Massachusetts Instamaations:

Installation must be performed by a qualified

or licensed contractor, plumber or gas fitter

qualified or licensed by the state, province or

region where this appliance is being in-

stalled.

Shut-off valve must be a "T" handle gas

cock.

Flexible gas connector must not be longer

than 36 inches.

If the information in this manual is not

followed exactly, a fire or explosion may

result causing property damage, personal

injury or death.

m Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO _F YOU SMELL GAS

[] Do not try to light any appliance.

[] Do not touch any electrical switch.

[] Do not use any phone in your building.

[] Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

[] If you cannot reach your gas supplier, call the

fire department.

Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

,_ WARNtNG

m All Ranges can tip

m Injury to Persons

could result

m lnstaHAnti-Tip Device

m See _nstaHation

Instructions

TO REDUCE THE RiSK OF TIPPING OF THE

APPMANCE, IT MUST BE SECURED BY A

PROPERLY INSTALU=D ANTI-TIP DEVICE.

VERIFY THAT TH_=ANTi-TIP D_=WC_=IS _=NGAG _=D

PER INSTALLATION INSTRUCTIONS. (NOTE:

ANTi-TIP DEVICE IS REQUIRED ON ALL 30" AND

36" RANGES)

Note: This Range is NOT designed for installa-

tion in manufactured (mobile) homes orfor instal-

lation in Recreational Park Trailers.

Do Not install this range outdoors.

Contents

Important Installation Information ................. 1

Step 1: Ventilation Requirements ................ 2

Step 2: Cabinet Preparation ................. 3 - 7

Step 3: Unpacking, Moving

and Placing the Range ......................... 8 - 9

Step 4: Installing AntioTip Device ...... 10 - 11

Step 5: Gas Requirements and Hookup .... 12

Step 6: Electrical Requirements,

Connection and Grounding ....................... 13

Step 7: Backguard Installation .................. 14

Step 8: Door Removal and Installation ...... 15

Step 9: Burner Test and Adjustment.. 16 - 17

Installer Checklist ...................................... 18

To Clean and Protect Exterior Surfaces .... 18

Important Installation Information

GAS type verification

Verify the type of gas supplied to the location. Ensure

that the appliance is connected to the type of gas for

which it is certified. All ranges are certified for use with

natural gas or propane (LP) gas. Make certain the

range matches the gas type available.

Important

* A backguard must be utilized when there is less than

a 12" horizontal clearance between combustible ma-

terials and the backedge of the range. The Thermador

Low Back backguard must be ordered separately and

installed at the rear of the range. For island installa-

tions and other installations with more than 12" clear-

ance, an optional stainless steel Island Trim is avail-

able to cover the backguard mounting flanges.

. Verify that the appliance is correct for the type of gas

being provided. Refer to Step 5 on Page 12 before

proceeding with the installation.

Gas Supply:

Natural Gas - 6 inch water column. (14.9 mb) min,

14 inch (34.9 rob) max.

Propane Gas - 11 inch water column. (27.4 mb), min,

14 inch (34.9 rob) max.

Electric Power Supply:

30" Model:

4 Burners - 120 VAC, 60 Hz, IPh. 15Amp circuit.

36" Models:

6 Burners- 120 VAC, 60 Hz., IPh, 15Amp circuit.

4 Burners with Grill- 120VAC, 60 Hz, 1Ph, 15Amp circuit.

4 Burners with Griddle- 120 VAC, 60 Hz, IPh, 20 Amp

circuit.

48" Models:

6 Burners with Grill- 120VAC, 60 Hz, 1Ph. 15Amp circuit.

6 Burners with Griddle- 120 VAC, 60 Hz. IPh. 20 Amp

circuit.

4 Burnerswith Grill and Griddle- 120 VAC, 60 Hz, 1Ph, 20

Amp circuit.

CAUTION

When connecting the unit to propane gas, make

certain the propane gas tank is equipped with its

own high-pressure regulator in addition to the

pressure regulator supplied with the range. The

maximum gas pressure to this appliance

must not exceed 14.0 inches water column

(34.9 rob) from the propane gas tank to the

pressure regulator.

CAUTION

This unit is designed as a cooking appliance.

Based on safety considerations, never use itfor

warming or heating a room.

This appliance complies with one or more of the following

standards:

UL 858, Standard for the Safety of Household Electric

Ranges

UL 923, Standard for the Safety of Microwave Cooking

Appliances

• UL 507, Standard for the Safety of Electric Fans

ANSi Z21.1, American National Standard for House-

hold Cooking Gas Appliances

CANiCSA-C22.2 No. 113-M1984 Fans and Ventila-

tors

CAN/CSA-C22.2 No. 61-M89 Household Cooking

Ranges

It is strong_ recommended that this appliance be

installed in conjunction with a suitable overhead vent

hood. (See Step 1 for Ventilation Requirements.) Due

to the high heat capability of this unit, particular atten-

tion should be paid to the hood and duct work instal-

lation to assure it meets local building codes.

It is the responsibility of the owner and the installer to

determine if additional requirements and!or standards

apply to specific installations.

CAUTION

To eliminate risk of burns or fire caused by

reaching over heated surface units, cabinet

storage located above the surface units

should be avoided.

Check local building codes for the proper method of

appliance installation. Local codes vary. Installation,

electrical connections and grounding must comply

with all applicable codes. In the absence of local

codes the appliance should be installed in accor-

dance with the National Fuel Gas Code ANSI Z223.1/

NFPA 54 current issue and National Electrical Code

ANSI/NFPA 70-current issue. In Canada, installation

must be in accordance with the CAN 1-B149.1 and .2

-Installation Codes for Gas Burning Appliances and/

or local codes.

Step 1

It is stron IgLv_recommended that a

suitable exhaust hood be installed

above the range. Downdraft

ventilation should notbe used. The

table below indicates the

Thermador hoods, by model

number, that are recommended

for use with all ranges.

1. Select Hood and

B ower Modems:

Forwall installations, the hood

width must, at a minimum,

equal the width of the range

cooking surface. Where

space permits, a hood larger

in width than the cooking sur-

face may be desirable for im-

proved ventilation perfor-

mance.

For island installations, the

hood width should, at a mini-

mum, overhang the range

cooking surface by 3" on each

side.

Ventilation Requirements

Ventilation hoods and blowers are

designed for use with single wall

ducting. However, some local

building codes or inspectors may

require double wall ducting. Con-

suit local building codes and/or

local agencies before starting to

assure that hood and duct instal-

lation will meet local requirements.

Do not install a microwave oven /

ventilator combination above the

range, as these types of units do

not provide the proper ventilation

and are not suitable for use with

the range.

Hood Placement:

The lower edge of the hood

should be installed a minimum

of 36" above the range cook-

ing surface. Also use a 36"

minimum clearance if the hood

contains any combustible

materials such as a wood cov-

ering. (See Figure 1).

Consider Make-Up

Air:

Due to the high volume of ven-

tilation air, a source of outside

replacement air is recom-

mended. This is particularly

important for tightly sealed and

insulated homes.

A qualified heating and venti-

lating contractor should be

consulted.

30" RANGE

36" RANGE

48" RANGE

PH30CS VTRI030D,

PHE30 / 36 VTR1530D,

orVTN1030C

HNW36YS VTRI030D,

orVTRI530D

PH36CS/42CS

PHE36 / 42

HNW36YS / 42YS

PH48CS / 54CS

PHE48 / 60

VTRI030D,

VTR1530D,

orVTNI030C

VTRI030D,

orVTRI530D

VTRI030D,

VTR1530D,

orVTNI030C

HNW48YS VTR 1030D,

or VTR1530D

HNI42YS VTRI030D

HTNI42YS orVTR1530D

HNI42YS VTRI030D

HTNI42YS orVTR1530D

HNI48YS / 54YS

HTNN8YS/54YS

VTR1530D

Notes: * For wall installations where adequate space is available, the installer or user may elect to

use a hood that is wider than the rangetop cooking surface. This may be particularly beneficial

for installations having a long duct run or when heavy usage of the grill is anticipated, in which

improved capturing of the cooking exhaust is desired.

•* Thermador offers a choice of remote (VTRI03OD or VTR1530D) or internal (VTN1030C)

blowers for use in wall installations.

Step 2: Cabinet Preparation

The range is a free standing unit. If the unit is to

be placed adjacent to cabinets, the clearances

shown in Fig. 1 are required. The same clear-

ances apply to island installations, except for the

overhead cabinets, which must have a space

wide enough to accept the flared island hood as

indicated in Fig. 1.

The 36" ranges may be recessed into the cabk

nets beyond the edge of the front face of the oven

(See Figures 2A and 2B). The 30" and 48" ranges

are not approved to be installed flush with the

cabinets.

CAUTION

In these installations, the door and cabinet on

36-inch models can cause a pinching hazard.

3. The gas and electrical supply should be within the

zones shown in Fig. 3A.

Any openings in the wall behind the range and in

the floor under the range must be sealed.

When there is less than a 12" horizontal clear-

ance between combustible material A and the

back edge of the range above the cooking sur-

face, a Thermador Low Back or Pot and Pan

Shelf must be installed. (See Fig. 2A). When

clearance to combustible material A is over 12",

a Thermador Island Trim may be used. (See Fig.

2B). Figures 2A and 2B indicate the space re-

quired for each type of backguard.

A three (3) inch minimum clearance is needed

when the range is installed beside a combustible

side wall.

Always keep appliance area clear and free from

combustible materials, gasoline and other flam-

mable vapors and liquids.

Do not obstruct the flow of combustion and ven-

tilation air to the unit.

Note: The maximum depth of over head cabinets

installed on either side of the hood is 13".

A 36-inch minimum clearance is required between

the top of the range and the bottom of an unprotected

cabinet. It is recommended that the bottom of the

wood or metal cabinet be protected by not less than

1,1'4inch of aflame retardant material covered with not

less than No. 28 MSG sheet steel, 0.015 inch (0.38

mm) thick stainless steel, 0.024 inch (0.6 mm) alumk

num, or 0.020 inch (0.5 mm) thick copper. Flame

retardant materials bear the following mark:

UNDERWRITERS LABORATORIES INC.

CLASSIFIED MINERAL AND FIBER BOARDS

SURFACE BURNING CHARACTERISTICS

Followed by the flame spread and smoke ratings,

these designations are shown as "FHC (Flame

Spread/Smoke Developed)." Materials with "O" flame

spread ratings are flame retardant. Local codes may

allow other flame spread ratings.

A As defined in the "National Fuel Gas Code"

(ANSI Z223.1 / NFPA 54, Current Edition).

Step 2: Cabinet Preparation

CAUTION:

Do not install the 30" and 48" ranges such that the oven door isflush

with the cabinet face. A flush installation could result in damage to

the cabinets due to exposure to high heat.

FIG. 1 Cabinet Clearances

18"

Min.

36"minimumfrombottomof

OverheadHoodtocooking

surface(also36"rain.ifhood

containscombustible

materialsA )

°°I

'35o7/8" iV]in,Range Height

with Leveling Legs fully

retracted

"36-3/4" Max. Range Height

with Leveling Legs fully

extended,

For 30" Ranges _ 30"or36"WideHood

36" or42" for Island

36"or42"Wide Hood

For 36" Ranges _.

42" or48"for Island

For 48" Ranges { 48", 54", or 60" Wide Hood

48" or54" for Istand

Cooking

Surface

For Electrical and Gas Supply Zone,

CAUTION: See Figs.

3" Min. to 2A, and 2B. 36"

combustible Min. to combustible

(_side watt_ material A,

materialA , I from cooking

(both sides) I surface

see Figure 3A. Zone size and position ,_

differ according to the model.

A as defined in the"National Fuet Gas Code" (ANSI Z223.1, Current Edition).

*The range height is adjustable. The level ofthe range top must beat the same

eve orabovethe countertop eve.

Step 2: Cabinet Preparation

F{G. 2A - Side View

/i'll / /// ////. /1// //// -- Combustible

_ 32-5/8'"

M_ials &

I _ 29-1/2" ,,

I Potan d _,,,]2-7/&"

Pan _ I

36"MIn. to ! Sh_tf "-4._ -I

Combustibles A I LOW L._

'_---- 26-3/8"

_25-112" max./

./Front Face

29-112"--

//// I

,[_----28-3/8" -----_-

47-3/8" 71

Kickplate

///I

3/8"

-'-Wall

////

A as defined in the "National Fuel Gas Code" (ANSI Z223.1, Current Issue).

FiG. 2B - Side View t

36" MIn._to

Combustibles A

12" Min. to

Combustibles A

with Island Trim

Island

/ Front Face

L J,

Note:

For Island Trim installations,

counter surface should have a

cantilever edge meeting the back

section of the Island Trim

accessory,

Countertop

Note:

If an inner wall is used under the

cantilever counter top, there

should be a 1/8" gap from the rear

of the range to the inner wall,

Step 2: Cabinet Preparation

GAS AND ELECTRIC SUPPLY ZONES:

F_G. 3A Gas & E_ectrica_ Supply Zones for AH Gas Ranges

Typical placement shown.

Other placement of

Electrical Supply and

Receptacle within the

Electrical and Gas Supply

Zone is acceptable.

NOTE:

If not already

present, install

gas shut-offvalve

in an easiJy

accessible

location. Make

sure all users

knowwhere and

how to shut off

the gas supply to

the range.

NOTE: The

installershould

inform the

consumer of the

location of the

gasshutzoffvalve.

3/4" Ftex Line to

Appliance

1/2"

NPT 120 VAC Receptacle

(Shown) or Junction

I Box

I .... Centerline of

Electrical

2" Maximum

Protrusion from Wait "_

_ a

for Gas Supply

Floor

Model A B C D E

30" 8" 12" 10" 6-1/2" 5ol/4"

36" 10ol/2" 15" 10ol/2" 6ol/2" 5ol/4"

48" 16-1/2" 16" 15-1/2" 6ol/2" 5ol/4"

The All Gas ranges may be con-

nected to the power supply with a

range supply cord (supplied with

range) or by hard-wiring to the power

supply. It is the responsibility of the

installer to provide the proper wiring

components (cord or conduit and

wires) and complete the gas con-

nection as dictated by local codes

and ordinances, and/or the National

Electric Code. The units must be

properly grounded. Refer to Step 6

for details.

The range must be connected

only to the type of gas for which

it is certified. If the range is to be

connected to propane gas, ensure

that the propane gas supply tank is

equipped with its own high pressure

regulator in addition to the pressure

regulator supplied with the range.

(See Step 5.)

NOTE:Any opening in the wall behind the appliance

and any opening in the floor under the appliance

must be sealed.

mMPORTANT:

The cord supplied with gas ranges having electric griddle requires

a NEMA 5-20 receptacle, shown here. Local codes may require

a different wiring method.

NEMA 5z20

RECEPTACLE

PLUG

Step 2 Cabinet Preparation

ELECTRICAL SUPPLY

Installation of the range must be planned so that the

rough-in of the junction box for the receptacle or

conduit connection will allow maximum clearance to

the rear of the unit.

To minimize binding when the unit is connected to

the receptacle or junction box, orient the receptacle

or conduit connector, and slide back into position.

F_G. 3B Wall Connection

I -1/4" Max. When

' . Plugged in

Power Cord & Receptacle

IMPORTANT

For all gas range models with an electric griddle, a

dedicated 20 Amp service is required for proper

operation.

Step 3 Unpacking, Moving and Placing the Range

CAUTION

Proper equipment and ad-

equate manpower must be

used in moving the range to

avoid injury, and to avoid

damage to the unit or the

floor. The unit is heavy

and shouJd be handled

accordingJy.

The range has an approximate

shipping weight as shown in

Chart A. The grates, griddle

plate and frame, burner caps,

front kick panel and oven racks

must be removed to facilitate

handling. This will reduce the

weight as shown in ChartA and

allow the range to pass through

30" doorways. See Figs. 2A

and 2B on Page 5. Do not

remove the grill or griddle

assemblies.

Remove the outer carton and

packing material from the ship-

ping base. The all gas ranges

are held to the skid by four (4)

bolts (see Fig. 4 and 5). After

removing the bolts the range

must be lifted and removed from

the skid.

mMPORTANT: Do not lift the

range by the oven door's

handJe, as this may damage

the door hinges and cause

the door to fit incorrectJy to

the oven cavity.

Cha_ A 30" Range 36" Range 48" Range

Shipping Weight 335 Jbs. 444 Ibs. 584 Jbs.

Weight without 285 Ibs. 390 Ibs. 524 Ibs.

packing materials

Without door(s),

burner caps, front kick

panel and oven racks

215 Ibs. 295 Ibs. 395 Ibs.

FIG. 4 - Removat of Two Front

Shipping BoJts

FiG. 5 - RernovaJ of Two Rear

Shipping BoJts

Left Rear ,if'Y"

Shipping

Bolt

NOTE: Leave adhesive-backed

foam layer over brushed-metal

surfaces to protect finish from

scratches, until the range is in-

stalled in final position.

Step 3: Unpacking, Moving and Placing the Range

Due to the weight, a dolly with soft wheels should

be used to move this unit. The weight must be

supported uniformly across the bottom (See Fig.

6).

After transporting the professional range by dolly

close to its final location, the range can be tipped

back and supported on the rear legs while the dolly

is carefully removed. THE FLOOR UNDER THE

LEGS SHOULD BE PROTECTED BEFORE

PUSHING THE UNiT mNTO POSlTmON. The

anti-tip device must be installed (Step 4), gas and

electrical connections should be made (Steps 5

and 6), and the backguard installed (Step 7)

before the range is placed in its final position.

For proper performance, the range must be

_eveL (It is very important for all products that

have the griddle feature.) The range is leveled by

adjusting the legs with a wrench.

Replace the kick panel and install the oven door.

To install door, see Page 15. Do not install the

oven door until the range is in its final loca-

tion. ff is important that the two (2) screws

retaining the kick pane_ are secure to prevent

accidenta_ access to hot surfaces.

Ensure that the burner caps are correctly

seated on the burner bases of the range's

cooktop.

Range

Musl be

Uniformly

Supported

by Braces

Provided

on Bottom

Range

22-3t4"

Remove all tape and packaging before using the

appliance. Destroy the packaging after unpacking

the appliance. Never allow children to play with

packaging material.

Grill / Griddle Tilt Adjustment (Notonallmodels)

Check the griddle frame adjustment by pouring two tablespoons of water on the back of the griddle

plate. The water should slowly roll into the grease tray. If not, adjust the two screws under the back

of the griddle frame. Start with one half turn CCW of the screws. Further adjustment should be made

by one=quarter turn until water slowly flows into the grease tray.

Step 4: Installing Anti-Tip Device

For aH 30" and 36" ranges, an anti-tip device must be installed as per these

instructions.

_, WARNING

RANGE TtPPING HAZARD

AH ranges can tip and injury can result.

To prevent accidental tipping of the range,

attach it to the floor, wall or cabinet by

installing the Anti-Tip Device supplied.

A risk of tip-over may exist if the appmi-

ance is not installed in accordance with

these instructions.

mfthe range is pulled away from the wall

for c_eaning, service or any other reason,

ensure that the Anti-Tip Device is prop-

er_y reengaged when the range is pushed

back against the wall. mnthe event of

abnorma_ usage (such as a person stand-

ing, sitting, or _eaning on an open door},

failure to take this precaution can result

in tipping of the range. Persona_ injury

might result from spilled hot _iquids or

from the range itself.

_, WARNING

o ALL RANGES CAN

T_P

o _NJURY TO PER-

SONS COULD RE-

SULT

o _NSTALL ANT_-T_P

DEVICES PACKED

W_TH RANGE

o SEE _NSTALLAT_ON

_NSTRUCT_ONS

WARNtNG

ELECTRICAL SHOCK HAZARD

. Use extreme caution when drilling ho_es

into the wall or floor. There may be con-

cealed electrica_ wires _ocated behind the

wall or under the floor.

. mdentify the e_ectricaL circuits that could

be affected by the installation of the Anti-

Tip Device, then turn off power to these

c ircu its.

. Failure to follow these instructions may

result in e_ectrica_ shock or other per-

sona_ injury.

ATTENTION

PROPERTY DAMAGE

. Contact a qualified installer or contrac-

tor to determine the proper method for

drilling ho_es through the wall or floor

materia_ (such as ceramic the, hardwood,

etc.}

. Do not s_ide the range across an unpro_

tected floor.

. Failure to follow these instructions may

result in damage to wall or floor cover-

ings.

Too_s Needed for Installation of Anti-Tip Device:

•Screwdriver, Phillips •Hammer

• Drill, electric or hand • Pencil or other marker

• Measuring tape or ruler

• 1/8" drill bit (wood or metal wall or floor)

•3/16" carbide:tipped masonry drill bit (concrete or concrete block wall or floor)

• 3/16" anchors, drywall or concrete, 4 each (not required if mounting bracket is being attached to solid wood or metal)

Step 4 Installing Anti -Tip Device

30" and 36" Ranges (Figures 7A and 7B)

Thermador Service Pa_ No. Qty

415078 4

487310 1

Description

Screw, Phillips, #10 x 1-1/2"

Anti-Tip Bracket, Floor-Mounted

_MPORTANT _NSTALLAT_ON _NFORMAT_ON:

• The anti-tip bracket may be attached to a solid

wood cabinet having a minimum wall thickness of

3/4".

• The thickness of the wall or floor may require use

of longer screws, available at your local hardware

store.

• In aJlcases, at least two (2) of the bracket mount-

ing screws must be fastened to solid wood or

metal.

• Use appropriate anchors when fastening the

mounting bracket to any material other than hard-

wood or metal.

• Prepare holes at fastener locations as identified

below:

For walls, wall studs, or floors composed of

F_G. 7A - Mounting Anti-tip Bracket

o e !

o oJ

solid wood or metal, drill 1/8" pilot holes.

For walls or floors composed of drywall,

sheet-rock or other soft materials, drill 3/16"

holes to a minimum depth of 1-3/4", then tap

plastic anchors into each of the holes using

a hammer.

For walls or floors composed of concrete or

concrete block, drill 3/16" holes to a mini-

mum depth of 1-3/4", then tap concrete

anchors into each of the holes using a

hammer.

For walls orfloors having ceramic tile cover-

_, drill 3/16" holes through the tile only, then

drill into the material behind the tile as indi-

cated immediately above.

If the range is moved to a new location, the Anti-

Tip Device must be removed and reinstalled.

MOUNTING ANT_-T_P BRACKET

The alternative floor mounted bracket shall be installed

as follows:

a) Place bracket on floor in position shown in Figure

7B.

b) Secure to floor or wall stud.

c) Later, when the unit is installed, the adjustable leg

will slide under the bracket.

F_G. 7B

- Placement of Anti-tip Bracket (Top View)

Wall Line

Cabinet

Floor

./ /

\--

Front (typical-

Right Cabinet I ether s de)

:_m 2oi/2, _ from edge of range

Step 5:

Verify the type of gas being used at the installation site.

As shipped from the factory, units are configured

for use with only natural gas or propane (LP) gas.

Make certain the range matches the type of gas

available at this location. These ranges are NOT

convertible between different types of gas.

For installation of the appliance at high altitude, please

consult your local gas company for their recommen-

dation of the correct orifice sizes and any other

necessary adjustments that will provide proper gas

combustion at specified altitudes.

CAUTION

When connecting unit to propane gas, make

certain the propane gas tank is equipped with its

own high pressure regulator in addition to the

pressure regulator supplied with the appliance.

The pressure of the gas supplied to the appli-

ance regulator must not exceed 14"

(34.9 mb) water column.

Supply Pressure:

Manifold Pressure:

Natural Gas Requirements:

Inlet Connection: 3/4" NPT external

1/2" NPT internal

(Minimum 3/4" dia. flex line.)

6" min. to 14" max. water column.

(14.9 to 34.9 mb)

5" water column (12.5 mb)

Supply Pressure:

Manifold Pressure:

Propane Gas Requirements:

Inlet Connection: 3/4" NPT external

1/2" NPT internal

(Minimum 3,14'' dia. flex line.)

11" min. to 14" max. water column.

(27.4 mb to 34.9 mb)

10" water column (24.9 mb)

WARNING

Gas Requirements and Hookup

HOOK UP

• A manual gas shut-off valve must be installed

external to the appliance, in a location accessible

from the front, for the purpose of shutting off the

gas supply. The supply line must not interfere with

the back of the unit. Make sure the gas supply is

turned off at the manual shut-off valve before

connecting the appliance.

• The range is supplied with its own pressure regu-

lator that has been permanently mounted within

the range body.

Use 3/4" flex line to connect between the gas

supply and the appliance inlet pipe, which exits the

upper rear of the appliance. The appliance pipe

connection has a 3/4" NPT external thread and a

1/2" NPT internal thread. (See Photo A.) Use

caution to avoid crimping the 3/4" flex line when

making bends.

• The gas supply connections shall be made by a

competent technician and in accordance with

local codes or ordinances. In the absence of a

local code, the installation must conform to the

National Fuel Gas Code ANSI Z223.1iNFPA54-

current issue.

Always use pipe sealing compound or Teflon®

tape on the pipe threads, and be careful not to

apply excessive pressure when tightening the

fittings.

• Leak testing of the appliance shall be in accor-

dance with the following instructions.

• Turn on gas and check supply line connections

for beaks using a soap and water solution,

Bubbles forming indicate a gas leak. Repair all

beaks immediately after finding them.

• Do not use a flame of any kind to check for

gas leaks.

Photo A

Gas line must not come in contact with any

components inside back cover of range. Run

gas line in channel in back of range.

Use 3/4" flex line to connect between the gas supply

and the appliance manifold pipe, which exits the

upper left rear of the appliance.

Step 6: Electrical Requirements, Connection & Grounding

Before installing, turn power OFF at the service

panel. Lock service panel to prevent power from

being turned ON accidentally.

Chart B: Electrica_ Suppmy Circuit Requirements

MODEL TYPE VOLTAGE CURRENTRATING FREQUENCY PHASE

30" 120 VAC 15 Amps 60 Hz. Single

36" 120 VAC 15 Amps 60 Hz. Single

36" with Grill 120VAC 15 Amps 60 Hz. Single

36" with Griddle 120 VAC 20 Amps 60 Hz. Single

48" with Grill 120VAC 15 Amps 60 Hz. Single

48" with Griddle 120 VAC 20 Amps 60 Hz. Single

48" with Grill 120 VAC 20 Amps 60 Hz. Single

and Griddle

A neutral supply wire must be provided from the

power source (breaker/fuse panel) because criti-

cal range components, including the surface

burner spark re-ignition modules, require 120

VAC to operate safely and properly. An improper

120 VAC power supply will cause malfunction,

damage to this appliance, and possibly create a

condition of shock hazard. If the correct power

supply circuit is not provided, it is the responsibil-

ity and obligation of the installer and user to have

proper power supply connected. This must be

accomplished in accordance with all applicable

local codes and ordinances by a qualified electri-

cian. In the absence of local codes and ordi-

nances, the power supply connection shall be in

accordance with the National Electrical Code.

Observe all governing codes and ordinances

when grounding. In the absence of these codes

or ordinances observe National Electrical Code

ANSI/NFPA No. 70 current issue.

Electric wiring diagrams and schematics have

been placed in the toe kick area of the range for

access by a qualified service technician.

iMPORTANT

For all gas ranges with electric griddle, dedicated 20 AMP service is required for proper operation.

Before you plug in an electrical cord, be sure all controls are in the OFF position.

For appliances equipped with a cord and plug, do not cut or remove the ground prong. It must be plugged into

a matching grounding type receptacle to avoid electrical shock. If there is any doubt as to whether the wall

receptacle is properly grounded, the customer should have it checked by a qualified electrician.

Installer - show the owner the location of the circuit breaker or fuse. Mark it for easy reference.

_, CAUTION

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-

off valve during any pressure testing of the gas supply piping system at test pressures equal to or less

than 1/2 psig (3.5kPa.).

The appliance and its individual shut off valve must be disconnected from the gas supply piping system

during any pressure testing of the system at test pressures in excess of 1/2 psig (3.5kPa.).

When checking the manifold gas pressure, the inlet pressure to the regulator should be at least 6.0" (14.9

mb) W.C. for natural gas or 11.0" (27.4 mb) for propane.

Do not attempt any adjustment of the pressure regulator.

Step 7: Backguard Installation

The backguard must be attached before sliding the

range into the final installed position. A Low Back or

Pot and Pan Shelf must be installed when there is less

than a 12" clearance between combustibles and the

back of the range above the cooking surface. (See

Fig. 2A and 2B on Page 5).

An Island Trim is available for covering the backguard

mounting flanges for island installations, where there

is a minimum of 12" of horizontal clearance between

combustibles and the back of the range. (See Fig. 2B

on Page 5).

The backguard is inserted, as shown in Fig. 8, into the

guide channels on the back of the range. Secure the

backguard with the (4) sheet metal screws provided.

Front of Unit

Chart C: Backguard Kit Mode_ Numbers

Model Width 9" Std. Low Back 12" Low Back 22" Pot and Pan Shelf

30" Included N!A HS30R

36" NiA LB36R HS36R

48" NiA LB48R HS48R

Backguard

Installed

3o3/4" island Trim

IT30R

IT36R

IT48R

Step 8: Door Removal and Installation

CAUTtON

USE CAUTION WHEN REMOVING THE

DOOR. THE DOOR IS VERY HEAVY.

o Make sure oven is cool and power to oven has

been turned off. Failure to do so could result in

electrical shock or burns.

, The oven door is heavy and fragile. Use both

hands to remove or replace the door.

o Grasp only the ends of the oven door handle.

o Failure to grasp the oven door firmly and properly

could result in personal injury and product

damage.

o With the door off, never release the levers and

try to close the hinges. Without the weight of the

door, the powerful springs will snap the hinges

closed with great force.

To Remove the Oven Door:

• Open the door fully and use a screwdriver to pry the

hinge clips away from the hinge slots. (See Photo

B.)

• Flip the hinge clip toward you. (See Photo C.)

• Close the door until it stops against the hinge clips.

The open hinge clips wilt hold the door open at a

slight angle.

• Grasp the door firmly on the ends of the door

handle, and lift the door up. (There will be some

spring resistance to overcome.) When the door is

lifted sufficient to clear the hinge hooks, the door

can be pulled straight out. (See Photo D.)

• Place the door in a safe and stable location.

To Reinstall the Oven Door:

• Position the door at a slight angle and insert the

hinges into the hinge slots - one on each side of the

range. The hinges will securely hook into the slots

when properly installed. Do not force, bend, or twist

the door.

Tip: Rest the door on your foot while using your leg for

stability.

• Open the door fully and use a screwdriver to push

the hinge clips all the way into the hinge slots. Be

careful not to scratch the range during this process.

To Check Door Fit and Operation:

• Open and close the door slowly to test the movement

and the fit of the door to the oven cavity. Do not force

the door to open or close, tf the door is properly

installed, it should move smoothly and rest straight

on the front of the range when closed.

• tf the door does not operate correctly, verify that the

hinges are properly seated into the hinge slots, and

that the hinge clips are fully engaged into the slots.

Photo B. Pry hinge clips out using a screwdriver.

Photo C. Flip hinge clips toward you.

Photo D. Hinges removed from oven.

Step 9 Burner Test and Adjustment

Install any loose components, such as burner caps

and grates that may have been removed earlier. Be

certain that burner caps seat properly into the burner

bases. Before testing operation of the appliance,

verify that the unit and the gas supply have been

carefully checked for leaks and that the unit has been

connected to the electrical power supply. Turn the

manual gas shut-off valve to the open position.

Test Rangetop Burners

Test Burner Ignition. Select a rangetop burner

knob. Push in and turn counterclockwise to HI. The

ignitor/spark module will produce a clicking sound.

Once the air has been purged from the supply lines,

the burner should light within four (4) seconds.

Test Flame: High Setting. Turn burner on to HI. See

Figure 9 for appropriate flame characteristics.

If any of the rangetop burners continue to burn mostly

or completely yellow, verify that the burner cap is

positioned properly on the burner base, then re-test. If

flame characteristics do not improve, call

Thermador@.

Test Flame: Low Setting. Turn burner on to LO.

Verify that the flame completely surrounds the burner.

There should be a flame at each burner port and there

should be no air gap between the flame and the

burner. If any burners do not carry over, call

Thermador@.

The two far left burners feature XLO®, causing the

flame to cycle on and off when the knob is set to the

XLO range. This is normal operation.

Repeat the Ignition and Flame Test procedures de-

scribed above for each rangetop burner and the grill

burner (if so equipped).

FIG. 9 Flame Characteristics

Yellow Flames:

Further adjustment is required.

Yellow Tips on Outer Cones:

Normal for LP Gas.

Soft Blue Flames:

Normal for Natural Gas.

Ifthe flame iscompletely or mostly yellow, verify that the

regulator is set for the correct fuel. After adjustment,

retest.

Some orange-colored streaking is normal during the

initial start-up.

Allow unit tooperate 4-5 minutes and re-evaluate before

making adjustments.

WHEN FLAME IS PROPERLY ADJUSTED:

. There should be a flame at each burner port.

. There should be no air gap between the flame

and burner port.

The gas grill uses a tube-style burner that has an air

shutter which allows adjustment to the amount of

primary air inside the burner tube.

Air shutters of tube-style burners are pre-adjusted at

the factory, and usually do not require re-adjustment

except under rare conditions such as installation at

high altitude.

If grill burner/flame adjustment is required, go to the

procedure: "Flame Adjustment (if necessary)".

Step 9: Burner Test and Adjustment

Test Oven Burners

Remove the oven bottom cover. Remove the 4 screws

that attach the cover to the bottom of the oven, then lift

the cover and angled baffle plate out to expose the U-

shaped bake burner.

Test Bake Burner mgnition

Set the oven to BAKE at 350°F. After a short delay, the

burner will ignite. The burner will stay lit until 350°F is

reached and then shutoff. From this point forward, the

burner will cycle on and off to maintain the tempera-

ture.

Test Bake Burner Flame

While the bake burner is lit, inspect the flame. See

Figure 9 for proper flame characteristics. If the flame

burns completely or mostly yellow, it is necessary to

adjust the bake burner air shutter. See Figure 10 and

the Flame Adjustment procedure in the following

section.

Test Broil mgnition

Set cooking mode to BROIL. The broil burners will

ignite after 30-75 seconds.

F_ame Adjustment _if necessary}i."

ances have air shutter systems which are similar to

the illustration in Figure 10, and can be adjusted using

the following method (unless adjustment is not rec-

ommended). It is necessary to remove the burner

from the appliance in order to perform air-shutter

adjustments.

• Loosen shutter screw(s) and turn shutter to new

position.

• Adjust the shutter to more-closed position if the

flame is lifting or blowing, or is not carrying over.

Adjust the shutter to more-open position if the

flame is too yellow. (See Figure 10.)

• Re-tighten the shutter screw(s).

• After adjustment, re-installthe burnerand perform

flame evaluation. The air shutter must fit over the

orifice hood for proper operation of the burner.

• Repeat procedure as needed until flame char-

acteristics are acceptable. (See Figure 9.)

NOTE: The two infrared ceramic broil burners do not

have air shutters, so no adjustment is provided.

RepLace oven bottom cover. Slide cover into place

and reattach to bottom of oven cavity.

WARNtNG

Burner adjustments must be performed by a

qualified technician. Rmproper adjustments may

cause harmfu_ by-products or void the

appliance's warranty.

AHow burners to coo_ before attempting to

remove them!

F_G. 10 Air Shutter Adjustment (if necessary)

Screw

More Carryover

Less Lifting or Blowing

Call Thermador@ if:

1. Any of the burners do not light.

2. The broil burner or bake burner flame goes

out before the oven heats to the desired

temperature.

3. Any of the burners continue to burn yellow.

La page est en cours de chargement...

Thermador PRL486EDPG-01 Guide d'installation

Marque: Thermador

Modèle: PRL486EDPG-01

Catégorie: Fours

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Thermador PRL486EDPG-01 Installation guide

Thermador PRL486EDPG-01 Guide d'installation

Ce manuel convient également à

Thermador PRL486EDPG-01 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents