Admiral MDB5651AWB - Jetclean II Series Full Console Dishwasher Le manuel du propriétaire

Marque: Admiral

Modèle: MDB5651AWB - Jetclean II Series Full Console Dishwasher

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

M_AYI AG

MDB-5

I=l_l¢j;{Ct'iki1.,_!;!

Operating Tips ............. 2

Loading ................ 2-5

Dishwasher Use ............ 6

Cycles, Options

and Lights .............. 7-10

What Can &

Cannot be Washed ......... 10

Care & Cleaning .......... 11

Troubleshooting ........ 12-14

Warranty & Service ........ 15

Guide d'utilisation

et d'entretien .............. 16

Gui_ de Uso y Cuidado ..... 32

Part No. 6 919201 A www.maytag.com _2004 Maytag Appliances Sales Co.

Products with a .U_L)label have been listed with

Underwriter's Laboratories, Inc. - those with a CSA tag [lave

been listed with Canadian Standards Association.

Nevertheless, as with any other equipment using electricity

and moving parts, there is a potential hazard.

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this

manual are not meant to cover all possible conditions and

situations that may occur. Common sense, caution and care

must be exercised when installing, maintaining or operating

tile dishwasher.

Always contact your dealer, distributor, service agent or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words, Labels

Important Safety Instructions

1. Readall instructions before using the dishwasher.

2. Use the dishwasher only for its intended function.

3. Disconnect electrical power to dishwasher before

attempting to service.

4. Toavoid electrical shock hazard, the sides and back

must be enclosed and the front panels must be

attached before electrical power is applied to the

dishwasher. Refer to the installation instructions for

proper grounding procedures.

5. Connect to a properly rated, protected and sized

power supply circuit to avoid electrical overload.

6. Children should never be permitted to operate, or play

in, with, or around this dishwasher.

Z Toreduce tile risk of injury when loading items to be

washed, sharp or pointed items should be located with

the handles up. Also, load sharp items so they are not

likely to damage the door seal.

8. Do not touch the heating element on the bottom of

tile tub during or at tile completion of a cycle. It will

be hot.

9. Use only detergents and rinse additives designed for a

residential automatic dishwasher. Never use soap,

laundry detergent, or hand washing detergent in your

dishwasher. Keep these products out of reach of

children.

10. Do not sit, stand on or abuse tile door or dish racks of

the disilwasiler.

11. Under certain conditions, ilydrogen gas may be

produced in a ilot water system that ilas not been

used for two weeks or more. Hydrogen gas is

explosive. If the hot water system has not been used

for sucil a period, turn on all hot water faucets and let

tile water flow from eacil for several minutes. Tilis will

release any accumulated ilydrogen gas. As tile gas is

flammable, do not smoke or use an open flame during

tilis process.

12. Do not wash plastic items unless marked "dishwasher

safe" or tile equivalent. For plastic items not so

marked, cileck the manufacturer's recommendations.

13. Do not tamper witil controls.

14. To prevent accidental child entrapment and

suffocation risks, always remove tile door to tile

washing compartment when removing an old

dishwasher from service or discarding it.

15. Use caution when unloading tile dishwasher. Dishes

will be hot if unloaded shortly after a cycle has

completed.

16. Certified residential dishwashers are not intended for

licensed food establishments.

Save These Instructions

for Future Reference

Before You Start

, Don't prerinse. Simply scrape off any bones or

large food particles.

, If connected to a food waste disposer, make certain

the disposer is empty before starting the

dishwasher.

, Scrape off tomato-based food soils [see page 11}}.

, Remove certain foods such as mustard,

mayonnaise, lemon juice, vinegar, salt or dressings

from stainmess steem flatware as soon as possibme°

These foods may cause rusting and pitting if allowed

to remain in contact with the surface for an extended

period of time.

Operating the Dishwasher

1. After loading the dishwasher and adding detergent,

select the desired cycle and options by pressing

the pads. The indicator lights for the selected cycle

and options will illuminate. To cancel an option

press the pad again.

2. To start a cycle, close the door until it latches then

press the START/Cancem pad once. After a pause,

the fill will begin. The display countdown (select

models}} will flash until START!Cancem is pressed.

Adding a Forgotten item

For best cleaning, the forgotten item should be added

early in the cycle.

1. Grasp door handle and unlatch door without

opening completely. All lights will flash to indicate

that the cycle is suspended.

2. Wait for the water circulation to stop.

3. Open the door and add the item.

4. Close and latch the door. Lights will stop flashing

when the door is properly shut. After a slight delay,

the cycle resumes automatically at the point of

interruption.

, If the door is opened during a running cycle,

there may be up to a 30 second delay before the

dishwasher restarts after closing the door.

, Extended interruption of the wash cycle is not

recommended.

Loadlng

If START/Cancel is not pressed within 30

seconds of choosing your cycle, the dishwasher

will turn oft

The dishwasher remembers your last cycle so you

do not have to reset the cycle each time. To start

the dishwasher using the same cycle and options

selected on the previous wash, just press the

START/Cancel pad.

To cancel a running cycle, press the

START/Oancem pad once. The dishwasher will

drain, then shut off. To turn the dishwasher off

without draining, press the START/Oancem pad

twice. To prevent unplanned cycle or option

changes, these selections are "locked in" after 1

minute.

General Recommendations

(Rack features vary by mode[}

, Items can be centered behind a single tine or loaded

at an angle to maximize space.

, Avoid blocking or preventing the spray arms from

spinning freely. Do not allow items to extend beyond

the racks.

, Face soiled surfaces toward the center of the

dishwasher.

For best dishwashing results follow guidelines on

following pages to determine the best arrangement for

your items.

Conto

, If a cycle pad is pressed after the controls have

been "locked in," the light above the current cycle

will flash three times.

10 Place Setting Load

Upper Rack (Models with

folding and convertible bowl

tines in the lower rack)

Upper Rack (Models without

folding and convertible bowl

tines in the lower rack)

3breadand

hatterplates

areloadedon

therackunder

the

RackShelf

(select

models)

3saucersare

loadedonthe

rackunderthe

Stack-Rack

Shelf

(select

models)

Lower Rack (Models

with folding and

convertible bowl tines)

Lower Rack (Models

without folding and

convertible bowl tines)

Upper Rack

Glasses, cups, stemware, light-weight plastics, plates,

bowls, pans, Iong-handbd utensils etc. can be loaded

in this rack Do not load glasses over the tines.

The Stack-Rack (sebct

models} on the right side

of the upper rack folds

up or down for loading

flexibility. Fold it down to

hold long-handled

knives, spatulas and spoons or short items like cups or

juice glasses. Fold it up for taller items like glasses,

bowls, plates, etc.

The edge of the Stack-

Rack (select models} is

designed to hold

stemware in place. Taller

stemware will fit better on

the right side as the

upper rack is deeper on

this side.

The Folding Tines (select

models} located in the

front right corner provide

convenient loading space

for large, bulky items like

pots and pans or mixing

bowls.

To lower tines, carefully push the tines out of each

holder toward the center of the rack and lay the tines

down.

The Cup Clips (select

models} located in the

center of the upper rack

can be used to hold light-

weight plastic items,

cooking utensils, knives,

etc. in place. Clip the item

between the tine and the clip.

The Vari-Lock" Snugger

(select models} on the left

secures lightweight items

in place. It can be

adjusted by grasping the

wavy wire and rotating it

left to snug items against

the outer rack or to the

right to rest on top of light items. Do not load items

on top of the were.

For best results with tall

glasses, rest the bottom of

the glass against the wavy

wire of the Vari-Lock "_

Snugger (select models}.

Lower Rack

A variety of items such as

dinner plates, mixing bowls,

pots and pans and baking

dishes can be loaded in this

rack

Tall items such as bakeware

and large platters can be

placed on the left side.

With the Stack-

Rack (select

models} shelf

raised, thin items

like cookie sheets

or pizza pans

may be placed

along the left

side. With the shelf down, two levels of glasses and

cups can be loaded.

Positioning the Fold-

Away" Tines (select

models} flat in the back,

left corner provides

convenient loading space

for large, bulky items like

pots and pans or mixing

bowls.

Back

Convertible Tines (select

models} in the back, right

corner can be adjusted to

provide narrow spacing for

loading plates or wide spacing

for loading deep bowls, pots or

pans. Flip tines up for narrow

spacing or down for wider

spacing.

Back

i .......

Utensil Baskets

Removable Standard Utensil Basket {select

models}

For best cleaning results, prevent

items from nesting together by

placing some items in the basket

with handles up and some with

handles down. Load knives,

handles up and spoons and forks

handles down, through the slots in

the hinged covered section(s}

(when closed}.

Be sure that thin, finely pointed items do not extend

through the baskeL This could block the lower wash

arm.

Small, lightweight items like baby spoons and plastic

measuring spoons should be placed in the section(s}

with the hinged cover(s}.

Spilt & }:it TM Utensit Basket

(select models)

The split silverware basket can

be separated and placed in

several locations in the bottom

rack. Load flatware and utensils

into both sections or just one,

depending on your load.

To split the basket, hold the

basket

firmJy along

the sides.

Unlock

baskets as

shown here.

Auxiliary Basket {select models}

Use this supplemental

basket in the upper rack

for loading miscellaneous

items and utensils. This is

also a safe place to bad

sharp knives and pointed

items.

Conto

Adjustable Rack

(select models)

The Adjustabme Upper Rack (semect modems[} can be

raised or lowered to accommodate taller plates,

platters, pans, etc. optimizing useable space in both

upper and lower racks. Full size dinner plates can be

loaded in the upper rack if it is in the lower position.

Always adjust the upper rack before loading.

To mower the rack:

1. Pull the rack fully out.

2. Place thumbs on

each lever on

the adjuster

while holding

rack with hands.

Adjusters

3. Press down on

the levers with

thumbs and

push rack down.

The rack will come to a stop when it is in position.

To raise the rack:

1. Pull the rack fully out.

2. Place hands on both sides and lift up until rack

comes to a stop and latches in place.

. The dishwasher will not

operate correctmy if the

rack wash arm

connection is not amigned

with one of the water

intact homes on back wall

of the dishwasher.

The left and right side adjusters on the racks

must both be fully in the upward or downward

position for proper connection.

Removing the Upper Rack

The rack can be removed when tail or oversized items

need to be loaded into the lower rack. Unload the

rack before removing it from the dishwasher.

To remove rack with push tab rack stops (select

modelsl}:

Roll the rack '/:_to '/_of the way out.

To remove each plastic push tab rack stop from the

end of each track, push inward (toward the rack} on

the ridged area of the rack stop. The rack stop will

snap open and can be easily removed by pulling

straight ouL Take

care to support the

track while

removing rack

stops.

Roll the rack all ......

the way out of the

track and remove

from the

dishwasher_ Push Tab

Rack Stop

To replace:

Reverse the above procedure to replace the rack into

the dishwasher_

To remove tack with tab-lock tack stops

(select models]l

Roll the rack 1/3 to 1/2 of the way out.

Locate the rack stops at the end of each track.

Squeeze the tab in the middle of the rack stop and

pull the rack stop straight out. Take care to support

the rack while removing the rack stops.

Roll the rack all the way out of the track and remove

from the

dishwasher_ I

Tab Lock

Rack Stop

To replace:

1. Replace the

dishwasher rack

by guiding the

wheels into the

tracks.

Push each rack stop

squarely into the end of the track until

the catch pops into the small hole on the

side of the track

Hot Water

For optimal cmeaning and drying results, hot water

is necessary° The incoming water temperature

should be 120 ° I: {[49° C) to properly activate the

detergent and memt greasy food soHso

To check the incoming water temperature, turn on the

hot water faucet nearest the dishwasher and let it run

into a glass in the sink. Place a candy thermometer in

the glass and check the temperature once it has

stopped rising.

Add recommended amount of detergent to each cup

as shown and close the detergent lid.

Use a detergent designed specifically for use in an

automatic dishwasher. Be sure it is fresh. Store

granular detergent in a cool, dry place (not under the

sink}.

Recommended Amount

Too little detergent results in poor cleaning, hard water

filming!spotting and poor drying. Too much detergent

can cause permanent etching/cloudiness.

The amount of detergent to use is determined by the

hardness of the water and soil level of the load. Refer

to the following chart for detergent usage

recom mendations.

Light Soil 2 tsp 6 tsp

Soft (0-4 gpg) Normal Soil 4 tsp 6 tsp

Heavy Soil 4 tsp 7 tsp

Light Soil 4 tsp 6 tsp

Medium (5-9 gpg) Normal Soil 4 tsp 6 tsp

Heavy Soil 5 tsp 7 tsp

Hard (10-12 gpg) All Levels 5 tsp 8 tsp

'Your local water utility or state university extension service can tell

you the degree of water hardness in your area.

Unextremely hard water conditions (13 grains per

gallon or morea), it is difficult to achieve good

results with any dishwasher. A mechanical water

softener may be necessary to improve water

quality, detergent effectiveness, and protect the

dishwasher parts from the damage that hard

water can cause°

Do not use detergent with the Rinse Onmy cycle.

Leave the detergent lid open when running Rinse

Only.

Rinse Aid

Regular use of a rinse aid improves drying,

reduces spotting and filming, and reduces

moisture left on the dishwasher interior.

An automatic rinse aid dispenser is located next to the

detergent cup.

The window next to the dispenser cap indicates when

the rinse aid reservoir needs to be refilled. When the

level of rinse aid is below the indicator marks and the

window is nearly clear, it is time to refill the dispenser.

Check the dispenser

monthlyo

To add rinse aid to the

dispenser, turn the cap

counterclockwise to open.

Remove the cap and pour

liquid rinse aid into the

opening. The amount of rinse aid dispensed during the

cycle is adjustable by moving the lever inside the reservoir

area. For most water conditions use the manufacturer

recommended setting of "2". Adjust it up to the "MAX"

setting for hard water. Set the lever anywhere between

these amounts as needed to get the best results. Replace

the cap and turn it clockwise to close.

Cycles,OptionsondLights

Cycmes

Choose the cycle that best describes your dishload by pressing the corresponding touchpad. (See page 2,

Operating Tips, for how to begin the cycle).

Heavy Wash Long cycle for heavy food soils. 131 2 washes/3 rinses

Medium cycle for average food

Normal Wash soils, Precision CleanTM Turbidity 97-118 1-2 washes*/1-2 rinses*

sensor is active with this cycle,

Light Wash Short cycle for light food soils, 82 2 washes/1 rinse

Designed to select the number

Auto Clean of water fills best suited for the

soil level of each load, Precision 97-131 1-2 washes*/1-3 rinses*

(select models) Clean°'Turbidity sensor is active

with this cycle.

Rinses dishes being held until 9 1 rinse

Rinse Only there is a full load.

Quick Wash Quick cycle for light food soils, 38 I wash/1 rinse

(select models) Does not include drying time,

Numberof fills will varydependingonthe soillevelof eachload.

Notes

• Depending on water temperature, there may be time added to the cycle to bring water up to temperature.

• Cycle times shown in the numerical display (select models) will increase or decrease, based on each load's soil

level, water temperature and selected options.

• Only the following certified cycles have been designed to meet NSF requirements (NSF/ANSI 18/4 Residential

Dishwasher) for sanitization: Auto Clean (select models), Heavy Wash, Normal Wash and Light Wash.

Cycles,OptionsondLights

Cycle Options

In addition to choosing a cycle from page 7,choose as many available options as are needed for your dishload.

ToughScrubV

ToughScrub T"Plus

(select models)

Sanitize

(select models)

Selected when washing loads with hard-to-remove food soils.

Depending on which cycle is being used, this option adds

heat and/or wash time to the wash cycle.

Sanitizes dishware. When cycle monitor recognizes that the

proper conditions have been met, SANITIZED light will activate

at the end of the cycle. Sanitization may not be achieved if

there is an interruption of the cycle, power failure or if the

incoming water temperature is below 120° F (/49° C).

Heavy Wash

Normal Wash

Light Wash

Auto Clean (selectmodelsJ

Heavy Wash*

Normal Wash*

Light Wash*

Auto Clean* (selectmodels)

Extra Rinse Adds an additional rinse to cycle. An extra rinse helps to All cycles

(select models) improve results in hard water situations. (except Rinse Only)

Raises temperature in the final rinse to 160° F. This option can

160 ° Wash be used with any cycle except Quick Wash (select models) Heavy Wash

Normal Wash

(select models) and Rinse Only. Auto Clean* (selectmoaek_

Heated Dry

For enhanced drying results select this option. When Heated

Dry is not selected, towel drying of some items such as plastic

and items with non-stick surfaces may be necessary and more

moisture may be noticed adhering to the dishwasher interior.

In models with plastic interiors, it is normal to notice vapor

escaping from the door vent as the heat dries your dishes.

Vapor will escape even if Heated Dry is not selected.

All cycles

(except Rinse Only)

Only these cycles have been designated to meet NSF requirements (NSF/ANS1184 Residential Dishwashe0 fol sanitization.

Start/Cancel Starts and stops dishwasher. See page 2 under Operating Tips: All Cycles

Operating the Dishwasher, for explanation.

Used to automatically start the cycle at a later time. See page 9 All Cycles

Delay for instructions.

Control Lock Option Locks control touchpad to prevent unwanted use. See page 9 All Cycles

(select models) for instructions.

Cont.

0 |

The Demay option can be used to automatically start

the cycle at a later time to reduce daytime heat

buildup in the home or to take advantage of reduced

energy costs if available in your area. This option is

also useful for conserving hot water at times of high

household usage (showers, laundry,.

To set up a [}emay:

1. Select the appropriate cycle and options for the

load. Close the door.

2. Press the Demay pad until the desired amount of

delay time is selected.

3. The Demay indicator and the count down display

(select models_ will flash until the START!Cancem

pad is pressed.

As soon as the START/Cancel pad is pressed, the

flashing will stop and the delay time will begin

counting down. The Demay indicator will remain lit

until the delay time has counted down.

The cycle will automatically start as soon as the

delay time expires.

Control Leek

Option {[select models[}

The control touchpads can be locked to prevent

unwanted use. If this feature is activated between

cycles, the dishwasher cannot be operated until the

controls are unlocked. If desired, the controls can be

locked after a cycle or delay has started.

Setting the Control Lock:

1. Press the Heated Dry pad for three seconds.

2. An indicator light next to the lock graphic will

ilhminate when the controls are locked.

To Cancel:

I, Press the Heated Dry pad for three seconds.

2. The indicator light will go off.

, If a cycle or option pad is pressed after the

controls have been locked, the indicator light next

to the lock graphic will flash five times. On

selected models with a countdown display, the

display will flash an "L" simultaneously with the

lock indicator.

. This option does not lock the door, only the

dishwasher controls.

, If 30 seconds elapse between setting the cycle

and options and pressing the START!Cancem

pad, the dishwasher will turn off.

To cancem a Delay:

When the delay is counting down, press the Delay pad

again. The indicator light will go out and the cycle will

start or resume immediately.

To cancem a Delay and the cycle:

, Press ST,_RT!Cancem once to drain and turn off the

dishwasher.

Press START/Cancem twice to turn dishwasher off

without draining.

Cvcles,OptionsandLights

Lights/Display (seuectmode s)

TIME REMAINING Display Shows approximate minutes remaining in a cycle. The symbol "2H" will appear when cycle time is greater

than 99 minutes. Cycle times shown in the numerical display (select models) will increaseor decrease,

(select models) based on each load's soil level, water temperature and selected options.

CLEAN Light Illuminates at the end of the cycle and remains lit until the door has been open for 30 seconds

continuously.

DRYING Light Illuminates during the entire dry period and goes out when the cycle is completed.

(select models)

WASHING Light Illuminates during all rinse and wash portions of the cycle.

(select models)

HEATING DELAY Light Illuminateswhen cycle is being extended to heat tile water.

(select models)

SANITIZED Light Illuminates at the end of the cycle when conditions have been met to achieve sanitization. The light will

(select models) remain lit until the door has been open for 30 seconds continuously.

Notes

• When Sanitize is selected, cycles are monitored to assure sanitization. The SANITIZED light will not activate if sanitization

requirements are not met. This could happen if the cycle is interrupted, power failure occurs or incoming water

temperature is below 120° F (49° FJ.

• The CLEAN and SANITIZED indicator lights (select models_)will not relight after a power failure until after the next cycle is run.

WhatCanandCannotBeWashed

Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.

Aluminum Yes, except anodized. High water temperature and detergents may affect finish.

Cast Iron No Seasoning will be removed, and iron will rust.

Yes, except antique or Always check manufacturer's recommendation before washing. Antique, hand-

China/Stoneware hand-painted, painted or over-the-glaze patterns may fade. Gold leaf may discolor.

Crystal Yes, except antique or Always check manufacturer's recommendation before washing. Some types of

delicate crystal, leaded crystal may etch with repeated washings.

Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.

Glass Yes A specialty glass called milk glass can yellow with repeated dishwasher washing.

Gold-Plated Flatware No Will discolor.

Pewter, Tin No

Yes,top rack, except Always check manufacturer's recommendation before washing. Plastics vary in

Plastics disposable plastic items, their capacity to withstand high water temperatures and detergents. Disposable

plastic items are not dishwasher safe for this reason.

Yes Run a Rinse Only cycle if not washing immediately. Prolonged contact with

Stainless Steel foods containing salt, vinegar, milk products or juice could damage finish.

No, if has commercial Always check manufacturer's recommendation before washing. Run a Rinse

Sterling Silver or "darkening". Only cycle if not washing immediately. Prolonged contact with food containing

Silverplate salt, acid or sulfide (eggs, mayonnaise and seafood) could damage finish.

Commercial "darkening" may be removed by detergent.

Wooden Items No Wood may warp, crack or discolor.

CareandCleaning

Genera Recommendations

The dishwasher interior is normally self-cleaning.

Periodically check the bottom of the dishwasher tub

to see if any large particles remain.

Wipe the edge of the inner door liner to remove any

food soil splashes which occurred during loading.

When cleaning stainless steel, always wipe with the

grain. Never use products containing chlorine bleach

or citric add.

The color from some tomato-based food soils may

occasionally adhere to various components of the

dishwasher interior, causing temporary discoloration.

To minimize this:

Remove excess tomato-based food soils from

dishes before loading.

Run the Heavy Wash cycle when washing loads

containing tomato-based food soils.

Be sure to use a dishwasher detergent that

contains chlorine to better fight staining.

Standard Exterior

Stainless Steel Exterior

Cseleet models)

Light to moderate Soft damp cloth and liquid spray cleaner. Do Not use

abrasive powders or cleaning pads.

Daily cleaning and light soil Soft cloth or sponge and one of the following:

• Mild detergent and water

• A solution of white vinegar and water

• Formula 409 Glass and Surface Cleaner*, or similar

multi-surface cleaner.

• Do Not use products containing chlorine bleach or

citric acid.

Follow with rinse and dry.

Moderate to heavy soil Soft cloth or damp sponge and Bon AmP. Follow with

rinse and dry.

Streaks or fingerprints/restore shine Soft cloth and Stainless Steel Magic Spray**.

Discoloration Soft cloth or damp sponge and Cameo Stainless Steel

Cleaner*. Rinse immediately and dry.

Interior Light to moderate Soft cloth or damp sponge.

Discoloration, or tomato-based stain Switch dishwasher detergent to chlorine-based product.

*Brand names are trademarks of the respective manufacturer.

**Call 1-877-232-6771 to order.

Storage/Moving

Fill detergent cup with a fresh-scented dishwasher

detergent or baking soda and select the Normal

Wash cycle. Allow the dishwasher to complete the

cycle. Then turn the water supply off and drain the

dishwasher. To drain, press the START/Cancel pad

once to activate the dishwasher. Press START/Cancel

again to activate the drain. Operate the drain twice to

ensure most of the water is removed. Last, disconnect

the electrical supply and prop open the door.

When turning the water supply to the home off, the

water shut off at the dishwasher must be turned off

also.

Troubleshooting

CHECK THESE POINTS TO HELP SAVE YOU TiME AND MONEY.

Dishwasher will not fill • Press the START/Cancel pad to start the dishwasher.

• Be sure door is latched securely.

• Be sure the water is turned on.

• Check that the pad is properly selected for a cycle.

• Check your home's circuit breaker or fuse box.

• Check inlet [lose for a kink.

• Check water valve inlet for sediment and clean if necessary.

Dishwasher will not drain/

Water in tub bottom

Dishwasher adds water at

end of cycle

Detergent cup is not empty

Dishwasher seems noisy

Cycle takes too long [Heating

Delay light [select models]

stays on)

Dishwasher has an odor

Dishwasher leaks

• If hooked up to a food waste disposer, be sure the knock-out is removed from the

disposer inlet.

• Check for food obstruction in the drain or disposer.

• Check drain hose for a kink.

• Check your home's circuit breaker or fuse box.

• Check that the cycle is completed.

• This is normal. The sensor (select models) in the pump must stay submerged so a

short fill of water is added after the cycle's last drain.

• Check that the cycle is completed.

• Be sure dispenser is not blocked.

• Use fresh detergent stored in a cool, dry place.

• A water valve hiss during fill is normal.

• Water circulation sounds are normal.

• A thumping sound may be a wash arm bumping an item that is extending beyond the

racks. Readjust load to avoid obstructing wash arm.

• Chopping or grinding sounds may be heard as the internal food disposer chops hard

items like fruit seeds, nuts, etc.

• Humming during the drain is normal.

• A snap noise is the detergent cup lid hitting the door liner when the dishwasher door

is opened at the end of the cycle. This is normal.

• Proper installation affects the noise level.

• ToughScrub TM, ToughScrubTM Plus or Sanitize (select models) has been selected and

the cycle is extended to heat water.

• Check to see that the incoming water temperature is 120° F (49° C).

Run dishes being held in the dishwasher through a Rinse Only cycle.

Many dishwashers have a "new" smell when first installed. This will dissipate with use.

Dishwasher may not be draining properly. (See "Dishwasher Will Not Drain" section.)

For a strong odor, place baking soda in both sides of the detergent cup. Select Light

Wash cycle and allow the water to circulate for about 10 minutes. Interrupt the cycle

by unlatching the door and let it stand overnight. Restart the dishwasher by latching

the door and allow it to complete the cycle. Another alternative is to use a dishwasher

cleaning product such as Jet-Dry Dishwasher Cleaner*.

• Check that the dishwasher is level. (Refer to the Installation Instructions.)

• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use

only detergents designed for use in a dishwasher. Less detergent is needed in soft

water. Try another brand of detergent if sudsing continues.

• Follow directions closely on [low to add a forgotten item (log.2).

• To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached.

*Brand names are trademarks of the respective manufacturer.

Cont.

Troubleshooting

Display time suddenly drops • This is normal when the Auto Clean (select models) or Normal Wash cycle is

or increases by several selected and the dishwasher decides to skip or add a drain and refill.

minutes (:select models:)

Indicator lights flashing

Glasses are cloudy/spotted

Food soil remains on dishes

Items washed in the

dishwasher or the dishwasher

tub itself are stained/

discolored

• The countdown display (select models) flashes after a cycle is selected until the

START/Cancel pad is pressed.

• The countdown display (select models) and the delay indicatorflash after a delay is

selected until the START/Cancel pad is pressed.

• All active display indicatorsflash ifthe door isopened during a running cycle or delay.

• The currently selected cycle flashes if an attempt is made to change the cycle after

cycle "lock-in".

• The lock indicatorflashes and the countdown display (selected models) flashes an"L"

if a pad ispressed while the control lock is enabled.

• Select Extra Rinse (select models).

• Check water temperature. Incoming water should be 120° F(49° C).

• Always use a rinse aid.

• Confirm that the cloudiness is removable by soaking the item in white vinegar for

approximately 5 minutes. If removed, the problem is due to hard water. Adjust

detergent amount being used to match water hardness (pg. 6). Be sure detergent is

fresh, stored properly and is a high quality brand.

• If cloudiness is not removable, it is etching. This is an erosion of the surface of the

glassware and can be caused bywater that is too hot, from using too much detergent

or by prewashing. Detergent needs food soil to act upon. If etching has occurred, the

glassware is permanently damaged. Toprevent further etching, adjust the detergent

amount to match the water hardness, stop prewashing, and usewater heating options

only when incoming water temperature is below 120° F (49° C).

• Check water temperature (pg 6).

• Run hot water at the sink before starting the dishwasher.

• Select ToughScrub '°or ToughScrub TM Plus option (select models).

• Check water hardness and adjust detergent amount accordingly (log.6).

• Use fresh detergent stored in a cool dry place.

• Select proper cycle for the soil level (log.7).

• Make sure the upper rack wash arm connector is correctly aligned in one of the water

inlet holes (pg. 5).

• Load items so they do not block the wash arms (pg. 2-5).

• Load the utensil basket with knife handles up and spoon and fork handles down

through the slots in the covers.

• Do not place glasses over tines.

• Priorto loading,scrape off burnt on foods and wipe the starchyfilm from utensils usedwith

pasta,riceand oatmeal. Thesesoils require more energy than the restof the load to clean.

• Aluminum utensils or pans can leave marks when they rub against other items. Leave

a slight space between items.

• Iron deposits in the water can leave a yellow, brown or orange film on dishes or the

dishwasher tub. A rust filter may be needed, check with a water treatment company.

• Separate silver or silver-plated silverware from stainless steel. These metals can be

damaged by contact with each other during washing.

• Color from tomato sauces may adhere to the interior parts of the dishwasher (pg. 11).

If light staining has occurred, leave the door open to oxidize the stain away. Change

dishwasher detergent and be sure to usea dishwasher detergent that contains chlorine

to better fight staining.

• Certain dishwasher detergents may stain silver. Try another brand of detergent.

*Brand names are trademarks of the respective manufacturer.

Troubleshooting

Items not properly dried/

moisture is present on the

dishwasher interior after the

dry cycle

• Be sure Heated Dry is selected.

• Water droplets may form on the inner door as part of the drying process.

• Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid*

regularly, to improve drying. Turn the rinse aid selector toward the MAX setting.

• Check water temperature (pg. 6).

• Select Sanitize.

• Increase detergent amount to match water hardness (pg. 6).

• Load properly. (pg. 2-5)

• Plastic and items with non-stick surfaces are difficult to dry because they have a

porous surface which tends to collect water droplets. Towel drying may be necessary.

• Glasses and cups with concave bottoms hold water and require towel drying. Locate

these items on the more slanted side of the rack for improved results.

Dishware is chipped

Sanitized light does not

illuminate at the end of the

cycle (select models)

• Load dishes according to instructions so they do not strike each other (pg. 2-5).

• Washing fine antique china/crystal in the dishwasher is not recommended.

• Do not load glasses over the tines.

• Do not overload.

Sanitize was not selected.

Sanitization can only beachieved with the Auto Clean (select models), Heavy Wash,

Normal Wash or Light Wash cycles.

Sanitization may not be achieved if there is an interruption of the cycle, power failure

or if incoming water temperature is below 120° F (49° C).

Dishwasher door will not • Be sure adjustable racks (select models) are properly adjusted to upper or lower

close position (pg. 5).

•Brandnamesaretrademarksof the res3ectivemanufacturer.

Wurrumvu,d Service

What is Not Covered By These Warranties:

1. Conditions and damages resulting from any of the

following:

a. Improper installation, delivery, or maintenance.

b. Any repair, modification, alteration, or adjustment not

authorized by the manufacturer or an authorized

servicer.

c. Misuse, abuse, accidents, or unreasonable use.

d. Incorrect electric current, voltage, or supply.

e. Improper setting of any control.

2. Warranties are void if the original serial numbers have

been removed, altered or cannot be readily determined.

3. Products purchased for commercial or industrial use.

4. The cost of service or service call to:

a. Correct installation errors.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to the servicer.

5. Consequential or incidental damages sustained by any

person as a result of any breach of these warranties.

Some states do not allow the exclusion or limitation of

consequential or incidental damages, so the above

exclusion may not apply.

To Receive Warranty Service

To locate an authorized service company in your area

contact the Maytag dealer from whom your appliance was

purchased or call Maytag ServicessM,Maytag Customer

Assistance at the number listed below. Should you not

receive satisfactory warranty service, please call or write:

Maytag Services sM

Attn: CAIR" Center

RO. Box 2370, Cleveland, TN 37320-2370

U.S. 1-800-688-9900

Canada 1-800-688-2002

U.S. customers using TTY for deaf, hearing impaired

or speech impaired, call 1-800-688-2080.

Notes

When writing or calling about a service problem, please

include the following information:

a. Your name, address and telephone number;

b. Model number and serial number of your

appliance;

c. Name and address of your dealer or servicer and

the date the appliance was purchased;

d. A clear description of the problem you are having;

e. Water hardness, detergent brand and amount,

water temperature and cycle used;

f. Proof of purchase (sales receipt).

• User's guides, service manuals and parts information

are available from Maytag ServicessM,Maytag Customer

Assistance.

Maytag • 403 West Fourth Street North

P.O. Box 39 • Newton, Iowa 50208

NIA TAG

MDB-5

I:l_l:l_t_'dl,i f.'_E

Conseils d'utilisation ....... 18

Chargement .......... 18-21

Utilisation du

lave-vaisselle ............. 22

Cycles, options et

t6moins lumineux ...... 23-26

Articles lavables ou non

en lave-vaisselle ........... 26

Entretien et nettoyage ...... 27

Dbpannage ............ 28-30

Garantie et service ........ 31

Gui_ de Uso y Cuidado ..... 32

Lesproduits portant une etiquette (_) ont ete homologues par

Underwriter's Laboratories,Inc.- ceux portant une etiquette

CSAont ete homologues par la CanadianStandards Association

(CSA). Neanmoins,comme pour tout autre equipement utilisant

I'electriciteet des pieces mobiles,il y a undanger potentiel.

Securit6

Ce que vous devez savoir sur

les instructions de s curti

Lesinstructions de securite importantes et les avertissements

paraissant dans ce guide ne sont pas destines _ couvrir toutes

les situations et conditions eventuelles qui peuvent se

presenter. II faut faire preuve de bon senset de prudence Iors

de I'installation, de I'entretien ou de I'utilisation de I'appareil.

Prenez toujours contact avec votre detaillant, distributeur,

agent de service ou fabricant, au sujet de problemes ou

conditions que vous ne comprenez pas.

Reconnaissez les etiquettes, phrases

ou symboles sur la s6curite

Instructions de securite importantes

Conserver ces

1. Lire la totalite des instructions avant d'utiliser le lave-

vaisselle.

2. Utiliser le lave-vaisselle uniquement pour les

applications.

3. Debrancher le lave-vaisselle avant tout entretien.

4. Pour eviter tout risque de choc electrique, les c6tes et

I'arriere doivent 8tre fermes et le panneau avant doit

6tre fixe avant de brancher le lave-vaisselle. Se

reporter aux instructions d'installation pour les

met[lodes correctes de raise _ la terre.

5. Brancher le lave-vaisselle _ un circuit electrique

correctement protege, d'une puissance nominale

appropriee et avec ills de calibre adequat.

6. II ne faut jamais laisser les enfants utiliser ou jouer

dans, avec ou autour du lave-vaisselle.

7. Pour reduire le risque de blessure Iors du chargement

du lave-vaisselle, il faut placer les articles pointus ou

aiguises avec le manche vers le dessus. De meme,

Ioger les articles pointus pour qu'ils n'endommagent

pas le joint de la porte.

8. Ne pas toucher _ I'element chauffant au bas de la

cuve durant ou _ la fin d'un cycle car il est chaud.

9. N'utiliser que des detergents et des agents de rin(_age

con(_uspour un lave-vaisselle residentiel automatique.

Ne jamais utiliser de savon, de detergent lessiviel ou de

detergent de lavage _ la main dans votre lave-vaisselle.

Garder ces produits hors de portee des enfants.

10. Ne pas s'asseoir, se mettre debout ou maltraiter la

porte ou les paniers du lave-vaisselle.

11. Souscertaines conditions, de I'hydrogene peut se former

dans un systemed'eau chaude qui n'a pas ete utilise

pendant deux semaines ou plus. L'hydreg#ne est un

gaz explesif Si le systemed'eau chaude n'a pasete

utilise pendant une telle periode, ouvrir tousles robinets

d'eau chaude et laissercouler I'eau pendant plusieurs

minutes. Ceci diminuera I'accumulation d'hydrogene.

Comme il s'agit d'un gaz inflammable, ne pasfumer ou

utiliser de flamme vivedurant cette operation.

12. Ne pas laver d'articles en plastique ne portant pas

I'indication davable en lave-vaisselle>>.Pour des

articles en plastique sans indication, verifier les

recommandations du fabricant.

13. Ne pas circonvenir les commandes.

14. Pour eviter tout risque d'enfermement et/ou de

suffocation accidentelle d'un enfant, toujours enlever

la porte du compartiment de lavage Iorsque I'on

enleve un ancien lave-vaisselle ou qu'on le jette.

15. Faire preuve de prudence en dechargeant le lave-

vaisselle. La vaisselle peut etre chaude si elle est

dechargee peu de temps apres la fin d'un cycle.

16. Les lave-vaisselle_ usage residentiel certifie ne sont pas

con£;uspour les etablissements alimentaires

homologues.

instructions

Avant de ¢o encer

Ne pas pr_rincer° Ulsuffit de jeter os et gros

morceau× de nourriture°

. Si le lave-vaisselle est raccord6 _ un broyeur

dechets, veimmer_ ce que celui_ci soit vide avant

de mettre DeJave_vaisseHe en marche.

. Gratter Destaches tenaees laissees par Des

aiiments _ base de tomate (voir page 27).

. Emiminer certains amiments (tels que moutarde,

mayonnaise, jus de citron, vinaigre, sel et

vinaigrettes) des articles en acier ino×ydabme

aussi rapidement que possibme. Ces aliments

peuvent provoquer de la rouille et du piquage s'ils

restent en contact prolonge avec la surface.

UtiJisation du Jave-vaisseHe

Apres avoir charge le lave-vaisselle et ajout6 du

detergent, choisir le cycle et les options desires en

appuyant sur les touches. Les temoins lumineux

des options et cycles choisis s'allument. Pour

annulet une option, appuyer a nouveau sur la

touche.

Pour demarrer un cycle, fermer la porte jusqu'_ ce

qu'elle se verrouille, puis appuyer une fois sur la

touche START/Cancel (MUSE EN MARCHE/

AnnuJationD. A la suite d'une pause, le

remplissage commence. Le decompte de I'afficheur

(certains modeles) clignote jusqu'_ ce que I'on

appuie sur START!Cancel.

Remarque

* Si I'on n'appuie pas sur la touche START/Oancem

dans les 30 secondes suivant la selection du

cycle, le lave-vaisselle s'arrete.

Le lave-vaisselle se souvient du dernier cycle choisL

II n'est donc pas necessaire de reprogrammer le

cycle a chaque fois. Pour mettre en marche le lave-

vaisselle avec le meme cycle et les memes options

que ceux choisis Iors du lavage precedent, il suffit

d'appuyer sur la touche START/Cancel

Pour annulet un cycle en cours de fonctionnement,

appuyer une fois sur la touche START/Cancel Le

lave-vaisselle procede _ une vidange puis s'arrete.

Pour arreter le lave-vaisselle sans qu'il ne commence

une vidange, appuyer deux lois sur la touche

START/Cancel. Pour empecher des changements

non prevus de cycle ou d'option, il n'est plus

possible de changer ces selections apres 1 minute.

Remarque

, Si I'on appuie sur une touche de cycle apres le

verrouflhge des commandes, le t@moin lumineux

situe au-dessus du cycle en cours clignote trois lois.

Aleut d'un article oubii

Pour de meflleurs resultats de nettoyage, I'article oublie

devra etre ajoute au debut du cycle.

Saisir la poignee de porte et deverroufller la porte

sans I'ouvrir completement. Tousles temoins

hmineux clignotent pour indiquer que le cycle est

interrompu.

Attendre I'arret de la circulation d'eau.

Ouvrir la porte et ajouter I'articJe.

Fermer la porte et JaverrouiJJer. Les temoins

lumineux cessent de clignoter Iorsque la porte est

correctement fermee. Apres un court instant, le cycle

reprend automatiquement au point oQ il s'est arret&

Remarques

. Si la porte est ouverte pendant le fonctionnement

d'un cycle, il peut y avoir jusqu'a 30 secondes

d'attente avant que I'appareil ne se remette en

marche une lois la porte fermee.

. II n'est pas recommande d'interrompre le cycle de

lavage pendant une periode prolongee.

Char jemem

Recommandations d'ordre

(Les caract_ristiques des paniers varient selon le

module)

. Les articles peuvent etre centres derriere une tige de

retenue ou charges en biais pour tirer le meilleur

patti possible de I'espace.

. Eviter de bloquer les bras gicleurs. Ne rien hisser

depasser des paniers.

,Tourner les surfaces souillees vers le centre du lave-

vaisselle.

Pour obtenir les meflleurs resultats de lavage, observer

les directives suivantes pour determiner la disposition

qui convient le mieux aux articles a laver.

Suiteooo

Chargement

10 couverts

Panier sup_rieur (_modhles

avec tiges pliables et tiges

convertibles pour bols dans

le panier inf_rieur.)

Panier sup_rieur (mod_les

sans tiges pliables et tiges

convertibles pour bols darts

le panier inf_rieur.)

3 assiettes

pain et beurre

sont plac_es

sur le panier

SOBS

I'_tag_re

Stack-Rack

(certains

mod_les)

Partier inf_rieur

(mod_les avec tiges

pliables et tiges

convertibles pour bols.)

3 soucoupes

sent plac_es

sur le partier

SOBS

I'_tag_re

Stack-Rack

(certains

mod_les)

Partier inf_rieur

(mod_les sans tiges

pliables et tiges

convertibles pour bols.)

Partier sup6rieur

II peut recevoir verres, tasses, articles en plastJque

16get, assbttes, bob, casseroles, ustensJles _ long

manche, etc. Ne pas placer les verres sur les tiges

de retenue,

L'6tagere Stack-Rack

(certaJns modeles} _ la

droite du panbr

supeMeur, se rel6ve ou

s'abaJsse pour plus de

souplesse de

chargement. L'abaJsser pour retenir les couteaux, Jes

spatuJes et les cuill6res _ long manche ou les articles

courts comme les tasses et bs verres _ jus. La relever

pour Ioger les grands articles comme les verres, les

bob, les assJettes, etc.

Le bord de I'_tagere

Stack-Rack (certaJns

mod6les} est con_u pour

retenir les verres _ pied

en place. II est pref6rabJe

de placer les verres dont

le pied est plus long _ droJte, car le panier superieur

est plus profond _ cet endroit.

Les Tiges piiabies

(certaJns modebs}

sJtu6es dans le coin avant

droit, foumissent un

espace pratique pour bs

grands articles

encombrants comme bs

marmites ou bob

m61angeurs.

Pour abaJsser les tJges, les pousser soJgneusement

hors de chacun des supports et vers le centre du

panier pour les mettre _ plaL

Les attaches _ tasses

(certains mod6bs} situes

au centre du partier

sup6Meur, peuvent

recevoir des articles

legers en phstique, des

ustensibs de cuisine, des

couteaux, etc. Fixer

I'articb entre la tige et I'attache.

Le serreartJcles Vario[.eck'" (certaJns modules} sJtu6

gauche, permet de

maintenir en place les

articles 16gers. II peut 6tre

ajust(! en faJsant passer le

fil ondule vers la gauche

pour maJntenJr les articles

contre I'exterieur du

panier, ou vers JadroJte

pour qu'il repose sur bs articles 16gers. Ne pas

placer d'articJes sur ce fiL

Pour obtenJr de meJJJeursr6sultats avec les verres

hauts, poser le bas du verre

contre le fil ondule du serre-

articles Vari_[.oc_" (certaJns

modeles}.

La page charge ...

Admiral MDB5651AWB - Jetclean II Series Full Console Dishwasher Le manuel du propriétaire

Marque: Admiral

Modèle: MDB5651AWB - Jetclean II Series Full Console Dishwasher

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

Documents connexes

Maytag PDBL390AWB Le manuel du propriétaire

Admiral MDB5651AWB - Jetclean II Series Full Console Dishwasher Le manuel du propriétaire

Admiral MDB5651AWB - Jetclean II Series Full Console Dishwasher Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents