Chief PACHFK2 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
PACHFK2 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: This equipment must be installed and
assembled by qualified service personnel in accordance with
local building codes. The wall to which the mount is being
attached may have a maximum drywall thickness of 5/8"
(1.6cm).
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support the combined weight of the PAC-502 accessory
and all attached equipment not to exceed 200 lbs (90.72 kg).
DIMENSIONS
20.00
INSIDE
SPACING
.31
7.9
CUTOUTS PROVIDE CLEARANCE
FOR ELECTRICAL KNOCKOUTS ON
PAC-502 ENCLOSURE
1.50
38.1
18.60
472.6
1.75
44.5
20.21
OUTSIDE
SPACING
513.3
.84
21.4
.31
7.9
DIMENSIONS: INCHES
[MILLIMETERS]
Installation Instructions PACHFK2
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PACHFK2 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
3/16"
(Included) M4 Allen Head Bit
(Included)
A (2)
B (4)
08 x 1-1/2" C (16)
M7 x 40mm
F (8)
5/16-18 x 5/8"
E (8)
1/4"
G (1)
3/16"
D (1)
[M4 Allen Head Bit]
[Header/footer
brackets]
Installation Instructions PACHFK2
5
INSTALLATION
WARNING: IMPROPER INSTALLATION CAN RESULT IN
DEATH OR SERIOUS PERSONAL INJURY! This accessory
should be installed by qualified personnel.
IMPORTANT ! : The following installation procedure
assumes that a Chief PAC502 In-Wall Enclosure has
been purchased and is available for use during this
procedure. Dimensions for creating an opening in the
wall without having the PAC-502 as a template can be
found below.
Site Preparation
Locate and Prepare Mounting Site
IMPORTANT ! : This accessory is designed for in-wall
installation spanning a minimum of three wood studs, 16"
on center. Installation of this accesory and the PAC-502
in 2" x 4" wood stud wall results in nearly direct contact
with vertical studs and back wall. Inadequate space will
remain for electrical wires/cables, plumbing, ductwork, or
insulation. Locate installation accordingly.
1. Identify a suitable wall location for the in-wall enclosure.
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL WIRES OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surfaces is free
of electrical wires and cables before cutting, drilling, or
installing fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surfaces is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
2. Using a stud sensor, locate and mark studs.
3. Center and level PAC502 housing between marked studs.
(See Figure 1)
4. Using PAC502 housing as a template, draw pencil line
around housing. (See Figure 1)
NOTE: If the PAC502 is not available mark opening to height
dimension (See Figure 2) and to inside stud edge on
either side.
5. Cut drywall on outside edge of line and remove drywall.
(See Figure 1) and (See Figure 2)
Figure 1
Install PACHFK2 Frame Support Brackets
The exposed portion of the center wood stud must be removed.
WARNING: STRUCTURAL FAILURE HAZARD! FAILURE
TO TAKE ADEQUATE PRECAUTIONS CAN LEAD TO
DEATH OR SERIOUS INJURY! Ensure removal of center
stud will not cause unacceptable loss of structural strength.
Consult a qualified building contractor and applicable building
codes. (See Figure 2)
1. Remove exposed portion of center stud flush with upper
and lower drywall edges. (See Figure 2)
Figure 2
Wood Studs
PAC-502
4
20.375"
5
PACHFK2 Installation Instructions
6
2. Orient header and footer brackets (A) within the cut-out
drywall area. (See Figure 3)
Figure 3
3. Raise and lower brackets (A) until brackets rest against
center stud. (See Figure 4)
NOTE: Front flange on both upper and lower bracket should be
slid behind drywall. (See Figure 5)
Figure 4
Figure 5
4. Make sure upper and lower brackets are level and there is
a minimum of 20.375" between them at bracket centers and
at both ends of brackets.
5. Secure upper and lower brackets to center studs using four
08 x 1-1/2" Phillips flat head wood screws (B) at center
studs. (See Figure 6)
6. Secure upper and lower brackets to side studs using
sixteen M7 x 40mm connector screws (C) and M4 Allen
head bit (D). (See Figure 6)
Figure 6
(A) x 2
2
(A) x 2
Center Stud
Center Stud
3
Front
flange
of bracket
Drywall
(B) x 4
(C) x 16
6
5
Installation Instructions PACHFK2
7
7. Orient PAC-502 enclosure following the installation
instructions provided with the PAC-502 and slide enclosure
into opening between upper and lower brackets (A).
(See Figure 7)
Figure 7
8. Secure PAC-502 enclosure to brackets using eight 1/4" flat
washers (E) and eight 5/16-18 x 5/8" button head cap
screws (F) using the 3/16" hex wrench (G). (See Figure 8)
CAUTION: PAC-502 enclosure must be secured on both
sides to side studs using lag screws and bushings following
the installation instructions provided with the PAC502
accessory.
Figure 8
7
(F) x 8
(E) x 8
8
PACHFK2 Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8807-002020 Rev00
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
09/10
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief PACHFK2 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief PACHFK2 Installation guide