DeWalt DCCS672 Manuel utilisateur

Marque: DeWalt

Modèle: DCCS672

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

final page size: 8.5 x 5.5 in

If you have questions or comments, contactus.

Pour toute question ou tout commentaire, nouscontacter.

Si tiene dudas o comentarios,contáctenos.

1‑800‑4‑DeWALT

DCCS672, DCCS677

60V Max* Chain Saw

Scie à chaîne 60V max*

Sierra de Cadena de 60V Máx*

Instruction Manual

Guide D’utilisation

Manual de instrucciones

English (original instructions) 4

Français (traduction de la notice d’instructions originale) 17

Español (traducido de las instrucciones originales) 32

Fig. A DCCS672, DCCS677

Components

1 Variable speed trigger switch

2 Lock‑off lever

3 Chain brake / front hand guard

4 Guide bar

5 Saw chain

6 Sprocket cover

7 Bar lock nuts

8 Chain tensioning screw

9 Oil level indicator

10 Oil cap

11 Guide bar scabbard

12 Rear handle

13 Front handle

14 Battery housing

15 Battery Pack

16 Battery release button

17 Wrench

Composants

1 Gâchette à vitesse variable

2 Levier de verrouillage

3 Frein de chaîne/Carter de

poignéeavant

4 Guide‑chaîne

5 Chaîne coupante

6 Cache de dent de pignon

7 Écrous de blocage du guide‑chaîne

8 Vis de tension de la chaîne

9 Témoin de niveau d’huile

10 Bouchon du réservoir d’huile

11 Fourreau du guide‑chaîne

12 Poignée arrière

13 Poignée avant

14 Logement du bloc‑piles

15 Bloc‑piles

16 Bouton de libération du bloc‑piles

17 Clé

Componentes

1 Interruptor de gatillo

de velocidad variable

2 Palanca de bloqueo en apagado

3 Freno de cadena / protector

delantero de la mano

4 Barra de guía

5 Cadena de la sierra

6 Cubierta de rueda dentada

7 Tuercas de bloqueo de barra

8 Tornillo de tensión de cadena

9 Indicador de nivel de aceite

10 Funda de la barra de guía

11 Tapón del aceite

12 Mango trasera

13 Mango delantero

14 Caja protectora de la batería

15 Batería

16 Botón de liberación de la batería

17 Llave

Fig.B Fig.C

Fig.D Fig.E

Fig.F Fig.G

1/4" (6 mm)

75–100% charged

Chargé de 75 à 100 %

75–100% cargada

51–74% charged

Chargé de 51 à 74 %

51–74% cargada

< 50% charged

Chargé de < 50 %

< 50% cargada

Pack needs to be charged

Le bloc‑piles doit être rechargé

La batería tiene que cargarse

Indicators/Témoin/Indicador

Charging

Bloc‑piles en Cours

de Chargement

Unidad en Proceso de Carga

Fully Charged

Bloc‑piles Chargé

Unidad Cargada

Hot/Cold Pack Delay

Suspension de Charge Contre

le Chaud/Froid

Restraso por Unidad Caliente/

Fría

Fig.H Fig.I

Fig.J Fig.K

Fig. MFig. L

Fig.N

60°

.025"

(0.635mm)

ENGLISH

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non‑skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off‑position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch

on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of the

power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewelry or long hair

can be caught in movingparts.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTUREREFERENCE.

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated

(cordless) powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust orfumes.

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert

symbols and words to alert you to hazardous situations and

your risk of personal injury or propertydamage.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

(Used without word) Indicates a safety relatedmessage.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Intended Use

The DCCS672 chainsaw is designed for cutting logs up to 16"

(406 mm) indiameter.

The DCCS677 chainsaw is designed for cutting logs up to 18"

(508 mm) indiameter.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This chainsaw is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

English (original instructions)

WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

ENGLISH

General Chain Saw Safety Warnings

WARNING: Additional safety warnings

forchainsaws.

a ) Follow all instructions when clearing jammed

material, storing or servicing the chain saw.

Make sure the switch is off and the battery pack

is removed. Unexpected actuation of the chain saw

while clearing the jammed material or servicing may

result in serious personalinjury.

b ) Keep all parts of the body away from the saw

chain when the chain saw is operating. Before

you start the chain saw, make sure the saw chain

is not contacting anything. A moment of inattention

while operating chain saws may cause entanglement

of your clothing or body with the sawchain.

c ) Always hold the chain saw with your right hand

on the rear handle and your left hand on the front

handle. Holding the chain saw with a reversed hand

configuration increases the risk of personal injury and

should never bedone.

d ) Hold the power tool by insulated gripping

surfaces only, because the saw chain may contact

hidden wiring. Saw chains contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electricshock.

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

e ) Do not use a battery pack or tool that is damaged

or modified. Damaged or modified batteries may

exhibit unpredictable behavior resulting in fire,

explosion or risk ofinjury.

f ) Do not expose a battery pack or tool to

fire or excessive temperature. Exposure to

fire or temperature above 265°F (130°C) may

causeexplosion.

g ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk offire.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust‑relatedhazards.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of

untrainedusers.

e ) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation. If

damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result in

a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

ENGLISH

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

a ) Maintain a firm grip, with thumbs and ﬁngers

encircling the chain saw handles, with both hands

on the saw and position your body and arm to

allow you to resist kickback forces. Kickback

forces can be controlled by the operator, if

proper precautions are taken. Do not let go of the

chainsaw.

b ) Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact

and enables better control of the chain saw in

unexpectedsituations.

c ) Only use replacement bars and chains speciﬁed

by the manufacturer. Incorrect replacement bars and

chains may cause chain breakage and/orkickback.

d ) Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increasedkickback.

The Following Precautions Should Be

Followed to Minimize Kickback:

1 . Grip saw firmly. Hold the chain saw firmly with both

hands when the motor is running. Use a firm grip

with thumbs and fingers encircling the chain saw

handles. Chain saw will pull forward when cutting on the

bottom edge of the bar, and push backward when cutting

along the top edge of thebar.

2 . Do not overreach.

3 . Keep proper footing and balance at alltimes.

4 . Don’t let the nose of the guide bar contact a log,

branch, ground or otherobstruction.

5 . Don’t cut above shoulderheight.

6 . Use devices such as low kickback chain and reduced

kickback guide bars that reduce the risks associated

withkickback.

7 . Only use replacement bars and chains specified by

the manufacturer or theequivalent.

8 . Never let the moving chain contact any object at the

tip of the guidebar.

9 . Keep the working area free from obstructions such

as other trees, branches, rocks, fences, stumps, etc.

Eliminate or avoid any obstruction that your saw chain

could hit while you are cutting through a particular log

orbranch.

10 . Keep your saw chain sharp and properly tensioned.

A loose or dull chain can increase the chance of

kickback. Check tension at regular intervals with the

motor stopped and tool unplugged, never with the

motorrunning.

11 . Begin and continue cutting only with the chain

moving at full speed. If the chain is moving at a slower

speed, there is a greater chance for kickback tooccur.

12 . Cut one log at atime.

e ) Wear eye protection. Further protective

equipment for hearing, head, hands, legs and feet

is recommended. Adequate protective equipment will

reduce personal injury from flying debris or accidental

contact with the sawchain.

f ) Do not operate a chain saw in a tree, on a ladder,

from a rooftop, or any unstable support. Operation

of a chain saw in this manner could result in serious

personalinjury.

g ) Always keep proper footing and operate the chain

saw only when standing on ﬁxed, secure and level

surface. Slippery or unstable surfaces may cause a loss

of balance or control of the chainsaw.

h ) When cutting a limb that is under tension, be

alert for spring back. When the tension in the wood

ﬁbers is released, the spring loaded limb may strike the

operator and/or throw the chain saw out ofcontrol.

i ) Use extreme caution when cutting brush and

saplings. The slender material may catch the

saw chain and be whipped toward you or pull you

offbalance.

j ) Carry the chain saw by the front handle with

the chain saw switched off and away from your

body. When transporting or storing the chain saw

always ﬁt the guide bar scabbard. Proper handling

of the chain saw will reduce the likelihood of accidental

contact with the moving sawchain.

k ) Follow instructions for lubricating, chain

tensioning and changing the bar and chain.

Improperly tensioned or lubricated chain may either

break or increase the chance forkickback.

l ) Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain

saw for cutting plastic, masonry or non‑wood

building materials. Use of the chain saw for

operations different than intended could result in a

hazardoussituation.

m ) Do not attempt to fell a tree until you have an

understanding of the risks and how to avoid

them. Serious injury could occur to the operator or

bystanders while felling atree.

Causes and Operator Prevention

ofKickback:

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in thecut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards

theoperator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards theoperator.

Either of these reactions may cause you to lose control of the

saw which could result in serious personal injury. Do not rely

exclusively upon the safety devices built into your saw. As a

chain saw user, you should take several steps to keep your

cutting jobs free from accident orinjury.

ENGLISH

• Chain Saw Powerhead ‑ A chain saw without the saw

chain and guidebar.

• Drive Sprocket or Sprocket ‑ The toothed part that drives

the sawchain.

• Felling ‑

The process of cutting down atree.

• Felling Back Cut ‑

The final cut in a tree felling operation

made on the opposite side of the tree from the notchingcut.

• Front Handle ‑ The support handle located at or toward

the front of the chainsaw.

• Front Hand Guard ‑ A structural barrier between the front

handle of a chain saw and the guide bar, typically located

close to the hand position on the fronthandle.

• Guide Bar ‑ A solid railed structure that supports and

guides the sawchain.

• Scabbard/Guide Bar Cover ‑ Enclosure fitted over guide

bar to help prevent tooth contact when saw is not inuse.

• Kickback ‑ The backward or upward motion, or both of the

guide bar occurring when the saw chain near the nose of

the top area of the guide bar contacts any object such as a

log or branch, or when the wood closes in and pinches the

saw chain in thecut.

• Kickback, Pinch ‑

The rapid pushback of the saw which

can occur when the wood closes in and pinches the moving

saw chain in the cut along the top of the guidebar.

• Kickback, Rotational ‑ The rapid upward and backward

motion of the saw which can occur when the moving saw

chain near the upper portion of the tip of the guide bar

contacts an object, such as a log orbranch.

• Limbing ‑ Removing the branches from a fallentree.

• Low‑Kickback Chain ‑ A chain that complies with the

kickback performance requirements of ANSI B175.1–2012

(when tested on a representative sample of chain saws.)

• Normal Cutting Position ‑ Those positions assumed in

performing the bucking and fellingcuts.

• Notching Undercut ‑ A notch cut in a tree that directs the

tree’sfall.

• Rear Handle ‑ The support handle located at or toward

the rear of thesaw.

• Reduced Kickback Guide Bar ‑ A guide bar which has

been demonstrated to reduce kickbacksignificantly.

• Replacement Saw Chain ‑ A chain that complies with

kickback performance requirements of ANSI B175.1–2012

when tested with specific chain saws. It may not meet

the ANSI performance requirements when used with

othersaws.

• Saw Chain ‑ A loop of chain having cutting teeth, that cut

the wood,and that is driven by the motor and is supported

by the guidebar.

• Ribbed Bumper ‑ The ribs used when felling or bucking to

pivot the saw and maintain position whilesawing.

• Switch ‑ A device that when operated will complete or

interrupt an electrical power circuit to the motor of the

chainsaw.

• Switch Linkage ‑ The mechanism that transmits motion

from a trigger to theswitch.

Chain Saw Names and Terms

• Bucking ‑ The process of cross cutting a felled tree or log

intolengths.

• Motor Brake (if equipped) ‑ A device used to stop the saw

chain when the trigger isreleased.

13 . Use extreme caution when re‑entering a previous cut.

Engage bucking spikes into wood and allow chain to reach

full speed before proceeding withcut.

14 . Do not attempt plunge cuts or borecuts.

15 . Watch for shifting logs or other forces that could

close a cut and pinch or fall intochain.

Kickback Safety Features

WARNING: The following features are included

on your saw to help reduce the hazard of kickback;

however such features will not totally eliminate this

dangerous reaction. As a chain saw user do not rely

only on safety devices. You must follow all safety

precautions, instructions, and maintenance in this

manual to help avoid kickback and other forces which

can result in seriousinjury.

• Reduced‑Kickback Guide Bar, designed with a small radius

tip which reduces the size of the kickback danger zone on

bar tip. A reduced ‑ kickback guide bar is one which has

been demonstrated to significantly reduce the number and

seriousness of kickbacks when tested in accordance with

safety requirements for electric chainsaws.

• Low‑Kickback Chain, designed with a contoured depth

gauge and guard link which deflect kickback force and

allow wood to gradually ride into the cutter. A low‑kickback

chain is a chain which has met kickback performance

requirements of ANSI B175.1–2012.

• Do not operate chain saw while in a tree, on a ladder, on a

scaffold, or from any unstablesurface.

• Hold tool by insulated gripping surfaces when performing

an operation where the cutting tool may contact hidden

wiring. Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock theoperator.

• Do not attempt operations beyond your capacity or

experience. Read thoroughly and understand completely all

instructions in thismanual.

• Before you start chain saw, make sure saw chain is not

contacting anyobject.

• Do not operate a chain saw with one hand! Serious injury

to the operator, helpers, or bystanders may result from one

handed operation. A chain saw is intended for two‑handed

useonly.

• Keep the handles dry, clean, and free of oil orgrease.

• Do not allow dirt, debris, or sawdust to build up on the

motor or outside airvents.

• Stop the chain saw before setting itdown.

• Do not cut vines and/or small underbrush.

• Use extreme caution when cutting small size brush and

saplings because slender material may catch the saw chain

and be whipped toward you or pull you offbalance.

ENGLISH

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs

WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into a

non‑compatible charger as battery pack may rupture

causing serious personal injury. Consult the chart

at the end of this manual for compatibility of batteries

andchargers.

• Charge the battery packs only in DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• DO NOT allow water or any liquid to enter batterypack.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack

can explode in a fire. Toxic fumes and materials are created

when lithium‑ion battery packs areburned.

• Do not expose a battery pack or appliance to ﬁre or

excessive temperature. Exposure to ﬁre or temperature

above 265°F (130°C) may causeexplosion.

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Wh ......................watt hours

Ah ....................... amp hours

or AC ...........alternating current

or AC/DC .... alternating or direct

current

...................... Class II Construction

(double insulated)

no .......................no load speed

n .........................rated speed

PSI....................... pounds per square

inch

......................earthing terminal

.....................safety alert symbol

..................... visible radiation

do not stare into

the light

..................... wear respiratory

protection

..................... wear eye protection

..................... wear hearing

protection

..................... read all

documentation

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

OPM .................... oscillations per

minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

Additional Safety Information

WARNING: Never modify the power tool or any part of

it. Damage or personal injury couldresult.

WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or dust

mask if operation is dusty. ALWAYS WEAR CERTIFIED

SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

WARNING: Some dust contains chemicals known

to State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these

chemicals are:

• compounds in fertilizers,

• compounds in insecticides, herbicides

andpesticides,

• arsenic and chromium from chemically

treatedlumber.

To reduce your exposure to these chemicals, wear

approved safety equipment such as dust masks that

are specially designed to filter out microscopicparticles.

WARNING: Use of this tool can generate and/or

disperse dust, which may cause serious and permanent

respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for

the dust exposure. Direct particles away from face

andbody.

WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.

CAUTION: When not in use, place tool on its

side on a stable surface where it will not cause a

tripping or falling hazard. Some tools with a large

battery pack will stand upright but may be easily

knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be caught

in movingparts.

• Switch Lockout ‑ A movable stop that prevents

the unintentional operation of the switch until

manuallyactuated.

ENGLISH

Important Safety Instructions for All

Battery Chargers

WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than a DeWALT charger. DeWALT

chargers and battery packs are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging DeWALT rechargeable battery packs.

Charging other types of battery packs may cause them to

overheat and burst, resulting in personal injury, property

damage, fire, electric shock orelectrocution.

• Do not expose the charger to rain orsnow.

• Do not allow water or any liquid to entercharger.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

The RBRC® Seal

Please take your spent battery packs to

an authorized DeWALT service center or

to your local retailer for recycling. In some

areas, it is illegal to place spent battery

packs in the trash. You may also contact your local recycling

center for information on where to drop off the spent

battery pack. Do not place in curbside recycling. For more

information visit www.call2recycle.org. or call the toll free

number in the RBRC®Seal.

RBRC® is a registered trademark of Call 2Recycle,Inc.

Attach the cap to the battery pack to ready it for shipping.

This converts the battery pack to three separate 20V

batteries. The three batteries have the Watt hour rating

labeled “Shipping” on the battery pack. If shipping without

the cap or in a tool, the pack is one battery at the Watt hour

rating labeled“Use”.

Example battery pack label:

USE: 120Wh SHIPPING: 3x 40Wh

In this example, the battery pack is three batteries with

40Watt hours each when using the cap. Otherwise, the

battery pack is one battery with 120Watthours.

Shipping the DeWALT FLEXVOLT™ Battery Pack

The DeWALT FLEXVOLT™ battery pack has a battery cap that

should be used when shipping the batterypack.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.

• Battery liquid may be flammable if exposed to spark

orflame.

• Never attempt to open the battery pack for any

reason. If the battery pack case is cracked or

damaged, do not insert into the charger. Do not crush,

drop or damage the battery pack. Do not use a battery pack

or charger that has received a sharp blow, been dropped,

run over or damaged in any way (e.g., pierced with a nail,

hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center forrecycling.

Storage Recommendations

The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold. Store the fully

charged battery pack out of thecharger.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the

battery pack using a cloth or soft non‑metallic brush. Do not

use water or any cleaningsolutions.

Fuel Gauge Battery Packs (Fig.B)

Some battery packs include a fuel gauge. When the fuel

gauge button is pressed and held, the LED lights will

indicate the approximate level of charge remaining. This

does not indicate tool functionality and is subject to

variation based on product components, temperature, and

end‑userapplication.

Transportation

WARNING: Fire hazard. Do not store, carry, or

transport the battery pack so that metal objects

can contact exposed battery terminals. For

example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc.,

with loose nails, screws, keys, coins, hand tools, etc.

When transporting individual battery packs, make

sure that the battery terminals are protected and well

insulated from materials that could contact them and

cause a short circuit. NOTE: Li‑ion battery packs should

not be put in checked baggage on airplanes and must

be properly protected from short circuits if they are in

carry‑onbaggage.

ENGLISH

4. Charger will not charge a faulty battery pack, which may

be indicated by the charging light(s) staying OFF. Take

charger and battery pack to an authorized service center

if light(s) stay(s)OFF.

NOTE: Refer to label near charging light(s) on charger

for blinkpatterns. Older chargers may have additional

information and/or may not have a yellow indicatorlight.

NOTE: To remove the battery pack, some chargers

require the battery pack release button to bepressed.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack may charge at a slower rate than a warm

batterypack.

The hot/cold pack delay will be indicated by the red light(s)

continuing to blink but with the yellow light continuously

ON. Once the battery pack has reached an appropriate

temperature, the yellow light will turn OFF and the charger

will resume the chargingprocedure.

DCB118 and DCB1112 Chargers

The DCB118 and DCB1112 chargers are equipped with

an internal fan designed to cool the battery pack. The fan

will turn on automatically when the battery pack needs to

becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li‑Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deep discharge. The tool will automatically

turn off and the battery pack will need to berecharged.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature

is between 65°F – 75°F (18° C– 24°C). DO NOT charge

when the battery pack is below +40°F (+4.5°C), or

above +104°F (+40°C). This is important and will

prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out

the lights;

c. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the heavier the cord and

thus the greater its capacity. An undersized cord will

cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size

to use depending on total length of all extension cords

plugged together, and nameplate ampere rating. If in

doubt, use the next heaviergauge.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

(meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

Ampere Rating

American Wire Gauge

More Than Not More

Than

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source.

The charger is ventilated through slots in the top and the

bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug. Have them replacedimmediately.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

• Foreign materials of a conductive nature, such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil or any buildup of metallic particles

should be kept away from the charger cavities and

ventilation slots.

• Always unplug the charger from the power supply

when there is no battery pack in thecavity.

Charging a Battery (Fig.C)

1. Plug the charger into an appropriate outlet.

2. Insert and fully seat battery pack. The red charging

light(s) will continuously blink whilecharging.

3. Charging is complete when the red charging light(s)

remain(s) continuously ON. Battery pack can be left in

charger or removed. Some chargers require the battery

pack release button to be pressed forremoval.

WARNING: Only charge batteries in air temperature

over 40° F (4.5° C) and below 104° F (+40°C).

ENGLISH

Replacing the Saw Chain (Fig.A, D, G)

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent accidental

operation, ensure the battery is removed from the

tool is unplugged before performing the following

operations. Failure to do this could result in serious

personalinjury.

1. To remove the saw chain5, place the saw on a flat,

firmsurface.

2. Remove sprocket cover6 as described in Installing the

Guide Bar and Saw Chainsection.

3. Rotate the chain tension screw8 using the flat

screwdriver end of thewrench17. Turning the screw

counterclockwise allows the guide bar4 to recede

and reduces the tension on the chain so that it may

beremoved.

Adjusting Chain Tension (Fig.A, E, F)

NOTE: Saw chain tension should be adjusted regularly before eachuse.

1. With the saw still on a firm surface check the saw

chain5 tension. The tension is correct when the saw

chain snaps back after being pulled 1/4" (6 mm) away

from the guide bar4 with light force from the middle

finger and thumb as shown in Fig.E. There should be no

“sag” between the guide bar and the saw chain on the

underside as shown in Fig.F.

2. To adjust saw chain tension, loosen bar lock nuts7.

3. Rotate the chain tension screw8 located on the

sprocket cover using the flat screwdriver end of

thewrench17.

4. Check saw chain tension, adjust ifneeded.

5. Do not over‑tension the saw chain as this will lead to

excessive wear and will reduce the life of the guide bar

and sawchain.

6. Once saw chain tension is correct, tighten bar lock

nuts7

untiltight using 6ft. lbs. (8 Nm) oftorque

7. A new chain stretches slightly during the first few hours of

use. It is important to check the tension frequently (after

removing the battery packunplugging tool) during the

first 2hours ofuse.

7. Once in place, hold the bar still, replace sprocket cover6.

Make sure bolt holes on the cover line up with the

bolts19, on the mainhousing.

8. Install the bar lock nuts7 and rotate clockwise with

the wrench 17 provided

until snug

, then loosen

the nut(s) one full turn, so that the saw chain can be

properlytensioned.

9. Using the flat screwdriver end of thewrench17 rotate

the chain tensioning screw8 clockwise to increase

tension. Make sure the saw chain5 is snug around the

guide bar4 as shown in Fig.E and Fig.F then tighten the

bar lock nut(s)7 untilsnug.

10. Follow the instructions in the section Adjusting

ChainTension.

Installing the Guide Bar and Saw Chain

(Fig.A, D–F)

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent accidental

operation, ensure the battery is removed from the tool

before performing the following operations. Failure to

do this could result in serious personalinjury.

If the saw chain5 and guide bar4 are packed separately in

the carton, the chain has to be attached to the bar, and both

must be attached to the body of thetool.

1. Place the saw on a flat, firmsurface.

2. Rotate the bar lock nuts7 counterclockwise with the

wrench 17provided.

3. Remove sprocket cover6, and bar lock nuts7.

4. Wearing protective gloves, grasp the saw chain5 and

wrap it around the guide bar4, ensuring the teeth are

facing the correctdirection.

5. Ensure the chain is properly set in the slot around the

entire guidebar.

6. Place the saw chain around the sprocket 20. While

lining up the slot on the guide bar with chain tensioning

pin18, and the bolt19, on the base of the tool as

shown in Fig.D.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Wall Mounting

Some DeWALT chargers are designed to be wall mountable

or to sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet, and

away from a corner or other obstructions which may impede

air flow. Use the back of the charger as a template for the

location of the mounting screws on the wall. Mount the

charger securely using drywall screws (purchased separately)

at least 1” (25.4mm) long, with a screw head diameter of

0.28–0.35” (7–9mm), screwed into wood to an optimal

depth leaving approximately 7/32” (5.5 mm) of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

4. You may charge a partially used pack whenever you

desire with no adverse effect on the batterypack.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non‑metallic brush. Do not use water or

any cleaningsolutions.

ENGLISH

Operating the Chain Saw (Fig.A, H, K)

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below may result

in electric shock, fire and/or serious personalinjury.

• Guard Against Kickback which can result in

severe injury or death. See General Power Tool

Safety Warnings and General Chainsaw

Safety Warnings, and Causes and Operator

Prevention of Kickback and Kickback Safety

Features, to avoid the risk ofkickback.

• Do not overreach. Do not cut above chest height.

Make sure your footing is firm. Keep feet apart.

Divide your weight evenly on bothfeet.

• Use a firm grip with your left hand on the front

handle13 and your right hand on the rear

handle12 so that your body is to the left of the

guidebar.

• Do not hold chain saw by chain brake/front hand

guard3. Keep elbow of left arm locked so that left

arm is straight to withstand akickback.

WARNING: Never use a cross‑handed grip (left hand

on the rear handle and right hand on the fronthandle).

WARNING: Never allow any part of your body to

be in line with the guide bar4 when operating the

chainsaw.

• Never operate while in a tree, in any awkward

position or on a ladder or other unstable surface.

You may lose control of saw causing severeinjury.

• Keep the chain saw running at full speed the entire

time you arecutting.

• Allow the saw chain to cut for you. Exert only light

pressure. Do not put pressure on chain saw at end

ofcut.

Installing and Removing the Battery Pack

(Fig.I)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack15 into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide it

into the handle until the battery pack is firmly seated in the

tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button16 and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

Proper hand position requires the left hand on the front

handle13, with the right hand on the rear handle12.

Proper Hand Position (Fig.H)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

OPERATION

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Transporting Chain Saw (Fig.A)

• Always remove the battery from the tool and cover the

guide bar4 with the scabbard11 when transporting

thesaw.

Saw Chain and Guide Bar Oiling (Fig.A)

Auto Oiling System

This chainsaw is equipped with an auto oiling system that

keeps the saw chain and guide bar constantly lubricated.

The oil level indicator9 shows the level of the oil in the

chainsaw. If the oil level is less than a quarter full, remove the

battery from the chainsaw and refill with the correct type of

oil. Always empty oil tank when finishedcutting.

NOTE: Use a high quality bar and chain oil for proper saw

chain and bar lubrication. As a temporary substitute, a

non‑detergent SAE30 weight motor oil can be used. The

use of a vegetable based bar and chain oil is recommended

when pruning trees. Mineral oil is not recommended

because it may harm trees. Never use waste oil or very thick

oil. These may damage yourchainsaw.

Filling the Oil Reservoir

1. Unscrew counterclockwise and then remove the oil

cap10. Fill the reservoir with the recommended bar and

chain oil until the oil level has reached the top of the oil

level indicator9.

2. Refit the oil cap and tightenclockwise.

3. Periodically switch the chainsaw off and check the oil

level indicator to ensure the bar and chain are being

properlyoiled.

Replacement chain and bar are available from your

nearest authorized servicecenter.

• The DCCS672 chain saw requires a replacement 18"

(45cm) chain DWO1DT618 and a replacement 18" (45cm)

barDWZCSB18.

• The DCCS677 chain saw requires a replacement 20"

(50cm) chain DWO1DT620 and a replacement 20" (50cm)

barDWZCSB20.

4. Wearing protective gloves, grasp the saw chain and lift

the worn saw chain out of the groove in the guidebar.

5. Flip guide bar over every time you replace the chain to

ensure evenwear.

6. Place the new chain in the slot of the guide bar, making

sure the saw teeth are facing the correct direction by

matching the arrow and graphic of the saw chain on the

sprocket cover6 shown in Fig.G.

7. Follow instructions for Installing the Guide Bar and

SawChain.

ENGLISH

• A retreat path should be planned and cleared as

necessary before cuts are started. The retreat path should

extend back and diagonally to the rear of the expected

line of fall as shownbelow.

DIRECTION

FALL

RETREAT

45°

TREE

45°

RETREAT

• Before felling is started, consider the natural lean of

the tree, the location of larger branches and the wind

direction to judge which way the tree will fall. Have

wedges (wood, plastic or aluminum) and a heavy mallet

handy. Remove dirt, stones, loose bark, nails, staples, and

wire from the tree where the felling cuts are to bemade.

• Notching Undercut - Make the notch 1/3 of the

diameter of the tree, perpendicular to the direction of

the fall. Make the lower horizontal notching cut first. This

will help to avoid pinching of either the saw chain or the

guide bar when the second notch cut is being made as

shownbelow.

• Felling Back Cut - Make the felling back cut at least 2"

(51mm) higher than the horizontal notching cut. Keep

the felling back cut parallel to the horizontal notching

cut. Make the felling back cut so enough wood is left

to act as a hinge. The hinge wood keeps the tree from

twisting and falling in the wrong direction. Do not cut

through the hinge as shownbelow.

• As the felling cut gets close to the hinge the tree should

begin to fall. If there is any chance that the tree may

not fall in the desired direction or it may rock back and

bind the saw chain, stop cutting before the felling cut

is complete and use wedges to open the cut and drop

the tree along the desired line of fall. When the tree

begins to fall remove the chainsaw from the cut, stop the

motor, put the chainsaw down, then use the retreat path

planned. Be alert for overhead limbs falling and watch

yourfooting.

2" (51 mm)

DIRECTION OF FALL

2" (51 mm)

HINGE

NOTCH

FELLING BACK CUT

Common Cutting Techniques

Felling

The process of cutting down a tree. Do not fell trees in high

windconditions.

WARNING: Felling can result in injury. It should only be

performed by a trainedperson.

WARNING: When not in use always have the chain

brake engaged and batteryremoved.

Setting the Chain Brake (Fig.K)

Your chain saw is equipped with a chain braking system

which will stop the chain quickly in case ofkickback.

1. Remove the battery from thetool.

2. To engage the chain brake, push the chain brake/front

hand guard3 forward until it clicks intoplace.

3. Pull the chain brake/front hand guard3 towards the

front handle13 into the “set” position as shown in Fig.K.

4. The tool is now ready touse.

NOTE: In the event of kickback, your left hand will come in

contact with the front guard, pushing it forward, toward the

workpiece. This will stop thetool.

Testing the Chain Brake (Fig.A, K)

Test the chain brake before every use to make sure it

operatescorrectly.

1. Place the tool on a flat, firm surface. Make sure the saw

chain5 is clear of theground.

2. Grip the tool firmly with both hands and turn the chain

sawon.

3. Rotate your left hand forward around the front

handle13 so the back of your hand comes in contact

with the chain brake/front hand guard3 and push it

forward, toward the workpiece. The saw chain should

stopimmediately.

NOTE: If saw does not stop immediately, stop use of tool and

bring it to an authorized service center nearestyou.

WARNING: Make sure to set chain brake

beforecutting.

ON/OFF Switch (Fig.J)

Always be sure of your footing and grip the chain saw firmly

with both hands with the thumb and fingers encircling

bothhandles.

1. To turn the unit on, push down on the the lock off

lever2, shown in Fig.J, and squeeze the trigger

switch1. Once the unit is running, you may release the

lock offlever.

2. In order to keep the unit running you must continue

to squeeze the trigger. To turn the unit off, release

thetrigger.

NOTE: If too much force is applied while making a cut the

saw will turn off. To restart saw, you must release the trigger

switch1 before the saw will restart. Begin your cut again this

time with less force. Allow the saw to cut at its ownpace.

WARNING: Never attempt to lock a switch in the

ONposition.

ENGLISH

MAINTENANCE

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Your DeWALT power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.

CUT FROM TOP (OVERBUCK)

AVOID CUTTING EARTH

• When supported at one end first, cut 1/3 the diameter

from the underside (underbuck). Then make the finishing

cut by overbucking to meet the firstcut as shownbelow.

2nd CUT OVERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT UNDERBUCK

(1/3 DIAMETER)

AVOID SPLINTERING

• When supported at bothends. First, cut 1/3 down from the

top overbuck. Then make the finished cut by underbucking

the lower 2/3 to meet the firstcut as shownbelow.

2nd CUT UNDERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT OVERBUCK

(1/3 DIAMETER)

TO AVOID SPLINTERING

• When on a slope always stand on the uphill side of

the log. When “cutting through”, to maintain complete

control reduce the cutting pressure near the end of the

cut without relaxing your grip on the chain saw handles.

Don’t let the chain contact the ground. After completing

the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving

from cut tocut.

Limbing

Removing the branches from a fallen tree. When limbing,

leave larger lower limbs to support the log off the ground.

Remove the small limbs in one cut. Branches under tension

should be cut from the bottom of the branch towards the

top to avoid binding the chainsaw as shown below. Trim

limbs from opposite side keeping tree stem between you

and saw. Never make cuts with saw between your legs or

straddle the limb to becut.

Bucking

WARNING: Recommend that first time users should

practice cutting on a sawhorse.

Cutting a felled tree or log into lengths. How you should

cut depends on how the log is supported. Use a saw horse

wheneverpossible as shownbelow.

1. Always start a cut with the saw chain running at

fullspeed.

2. Place the bottom spike21 of the chainsaw behind the

area of the initial cut as shownbelow.

3. Turn the chainsaw on then rotate the saw chain and bar

down into the tree, using the spike as ahinge.

4. Once the chainsaw gets to a 45° angle, level the

chainsaw again and repeat steps until you cut

fullythrough.

5. When the tree is supported along its entire length, make

a cut from the top (overbuck), but avoid cutting the earth

as this will dull your sawquickly.

ENGLISH

Repairs

The charger and battery pack are notserviceable. There are

no serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment (including brush

inspection and replacement, when applicable) should

be performed by a DeWALT factory service center or a

DeWALT authorized service center. Always use identical

replacementparts.

Saw Chain Sharpening (Fig.L–N)

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to

do this could result in serious personalinjury.

WARNING: Do not over file chain rakers, this will

increase the risk of kickback. If the chain has been

sharpened more than four times, replaceit.

Each time the chain is sharpened, it loses some of the low

kickback qualities and extra caution should beused.

It is recommended that a saw chain be sharpened no more

than fourtimes.

NOTE: The cutters will dull immediately if they touch the

ground/dirt or a nail whilecutting.

To get the best possible performance from your chainsaw it

is important to keep the teeth of the saw chain sharp. Follow

these helpful tips for proper saw chain sharpening:

1. For best results use a 5/32" (4 mm) file and a file holder

or filing guide to sharpen your saw chain. This will ensure

you always get the correct sharpeningangles.

2. Place the file holder flat on the top plate and depth

gauge of thecutter.

3. Keep the correct top plate22 filing angle line of 30° on

your file guide parallel with your chain (file at 60° from

chain viewed from the side) as shownin Fig. L.

4. Sharpen cutters on one side of the chain first. File from

the inside of each cutter to the outside. Then turn your

saw around and repeat the processes (2, 3, 4) for cutters

on the other side of thechain.

NOTE: Use a flat file to file the tops of the rakers (portion

of chain link in front of the cutter) so they are about .025"

(.635 mm) below the tips of the cutters as shownin Fig. M.

5. Keep all cutter lengthsequal as shownin Fig. N.

6. If damage is present on the chrome surface of the

top plates or side plates, file back until such damage

isremoved.

CAUTION: After filing, the cutter will be sharp, use

extra caution during thisprocess.

Recommended accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact DeWALT call 1‑800‑4‑DeWALT

(1-800-433-9258) or visit our website:www.dewalt.com.

Accessories

WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DeWALT recommended

accessories should be used with thisproduct.

Sprocket and Sprocket Cover (Fig.A, D, G)

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can

cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent accidental

operation, ensure the battery is removed from the

tool is unplugged before performing the following

operations. Failure to do this could result in serious

personalinjury.

1. Place the saw on a flat, firmsurface.

2. Remove sprocket cover6 as described in Installing the

Guide Bar and Saw Chainsection.

3. Wearing protective gloves, use a clean, soft bristle brush

to wipe away any saw dust, sticks, vines or other debris

that may have collected inside the sprocket cover6 and

around the chain5 or sprocket20.

4. Rotate the chain tension screw8 using the flat

screwdriver end of thewrench17. Turning the screw

counterclockwise allows the guide bar4 to recede

and reduces the tension on the chain so that it may

beremoved.

5. Wearing protective gloves, grasp the saw chain and

guidebar and lift them away from the tool.

6. Wearing protective gloves, use a clean, soft bristle brush

to wipe away any saw dust or other debris that may have

collected on the guide bar4 and around the chain5.

7. Install the chain, guide bar and sprocket cover6

as described in Installing the Guide Bar and Saw

Chain, Replacing the Saw Chainsections and adjust

chain tension properly before use as described in

theAdjustingChain Tensionsection.

Saw Chain and Guide Bar

After every few hours of use, remove the sprocket cover,

guide bar and chain and clean thoroughly using a soft bristle

brush. Ensure oiling hole on bar is clear of debris. When

replacing dull chains with sharp chains it is good practice to

flip the chain bar from bottom totop.

Cleaning

WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1approved eye

protection when performingthisprocedure.

WARNING: Never use solvents or other harsh

chemicals for cleaning the non‑metallic parts of the

tool. These chemicals may weaken the plastic materials

used in these parts. Use a cloth dampened only with

water and mild soap. Never let any liquid get inside the

tool; never immerse any part of the tool into aliquid.

ENGLISH

Three Year Limited Warranty

For warranty terms, go to https://www.dewalt.com/Legal/

Warranty/3‑Year‑Limited‑Warranty.

To request a written copy of the warranty terms, contact:

Customer Service at DeWALT Industrial Tool Co., 701East

Joppa Road, Towson, MD 21286or call 1‑800‑4‑DeWALT

(1-800-433-9258).

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1‑800‑4‑DeWALT

(1-800-433-9258) for a freereplacement.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of an

insurance loss, such as fire, flood or theft, your registration

of ownership will serve as your proof ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

• Register online at www.dewalt.com

FRANÇAIS

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise

àl’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Le risque de

choc électrique est plus élevé si votre corps est mis à

laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive. Ne

jamais utiliser le cordon pour transporter, tirer

ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à l’extérieur,

se servir d’une rallonge convenant à cette

application. L’utilisation d’une rallonge conçue pour

l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique est

utilisé. Ne pas utiliser d’outil électrique en cas de

fatigue ou sous l’influence de drogues, d’alcool ou

de médicaments. Un simple moment d’inattention en

utilisant un outil électrique peut entraîner des blessures

corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

AVERTISSEMENTS GÉNÉRAUX SUR LA

SÉCURITÉ DES OUTILS

AVERTISSEMENT : lisez tous les avertissements de

sécurité, toutes les instructions, les illustrations

et les caractéristiques fournis avec cet outil

électrique. Ne pas suivre toutes les instructions

comprises aux présentes peut conduire à un choc

électrique, un incendie et/ou des blessuresgraves.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN

USAGEULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sansfil).

Définitions: symboles et termes

d'alarmessécurité

Ces guides d'utilisation utilisent les symboles et termes

d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels

oumatériels.

DANGER : indique une situation dangereuse

imminente qui, si elle n’est pas évitée, entraînera la

mort ou des blessuresgraves.

AVERTISSEMENT : indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner la mort ou des blessuresgraves.

ATTENTION : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait

entraîner des blessures légères oumodérées.

(Si utilisé sans aucun terme) Indique un message

propre à lasécurité.

AVIS : indique une pratique ne posant aucun risque

de dommages corporels mais qui par contre, si rien

n’est fait pour l’éviter, pourrait poser des risques de

dommagesmatériels.

Utilisation prévue

La tronçonneuse DCCS672 est conçue pour l’élagage et la

coupe de bûches jusqu’à 406 mm (16po)) dediamètre.

La tronçonneuse DCCS677 est conçue pour l’élagage et la

coupe de bûches jusqu’à 508 mm (18po) dediamètre.

NE PAS utiliser en conditions humides ou en présence de

liquides ou de gazinflammables.

Cette tronçonneuse est un outil électriqueprofessionnel.

NE PAS laisser les enfants entrer en contact avec l’outil.

Une supervision est requise lorsque des utilisateurs

inexpérimentés utilisent cetoutil.

Français (traduction de la notice d’instructions originale)

AVERTISSEMENT : lire tous les avertissements

de sécurité et toutes les directives. Le non‑respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

FRANÇAIS

e ) Gardez les poignées et surfaces d’emprise propres

et libres de tout produit lubrifiant. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus faciles

àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en

tenant compte des conditions de travail et du

travail à effectuer. L’utilisation d’un outil électrique

pour toute opération autre que celle pour laquelle il a

été conçu estdangereuse.

h ) Garder vos mains et les surfaces de prise sèches,

propres et libres de graisse et de poussière. Les

mains et les surfaces de prise glissante ne permettent

pas la manutention et le contrôle sécuritaires de l’outil

dans les situationsimprévues.

5) Utilisation et entretien du bloc‑piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc‑piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc‑piles.

b ) Utiliser les outils électriques uniquement avec

les blocs‑piles conçus à cet effet. L’utilisation de

tout autre bloc‑piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc‑piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court‑circuit des bornes du bloc‑piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc‑piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc‑piles peut provoquer

des irritations ou desbrûlures.

e ) Ne pas utiliser de bloc‑piles ou outil qui a été

endommagé ou modifié. Les unités endommagées

ou modifiées peuvent avoir une réaction imprévisible

résultant en un incendie, une explosion ou un potentiel

deblessure.

f ) Ne pas exposer de bloc‑piles ou l’outil aux

flammes ou à des températures excessives.

L’exposition aux flammes ou à une température

au‑dessus de 130°C (265°F) pourrait causer

uneexplosion.

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position d’arrêt

avant de relier l’outil à une source d’alimentation

et/ou d’insérer un bloc‑piles, de ramasser ou de

transporter l’outil. Transporter un outil électrique

alors que le doigt repose sur l’interrupteur ou brancher

un outil électrique dont l’interrupteur est à la position

de marche risque de provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver son

équilibre en tout temps. Cela permet de mieux

maîtriser l’outil électrique dans les situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux‑ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

h ) Ne pas laisser votre connaissance acquise suite

l’utilisation fréquente des outils vous permettre

de baisser la garde et ignorer les principes de

sécurité de l’outil. Un acte irréfléchi peut causer une

blessure grave en une fraction deseconde.

4) Utilisation et entretien d’un

outilélectrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et doit

êtreréparé.

c ) Débranchez la fiche de la prise électrique et, si

amovible, retirez le bloc‑piles de l’outil avant

d’effectuer tout ajustement, changement et

entreposage de celui‑ci. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

La page charge ...

DeWalt DCCS672 Manuel utilisateur

Marque: DeWalt

Modèle: DCCS672

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCCS672 User manual
español: DeWalt DCCS672 Manual de usuario

Documents connexes

DeWalt DCCS620 Manuel utilisateur

DeWalt DCCS672 Manuel utilisateur

DeWalt DCCS672 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents