GUBI Timberline Floor Lamp Manuel utilisateur

Taper
Manuel utilisateur
ASSEMBLY INSTRUCTIONS
for
Timberline Floor Lamp
For enquiries contact GUBI A/S - CVR: 17940384
Klubiensvej 7-9. 2150 Nordhavn. Copenhagen, Denmark
T +45 69 15 60 60 – order@gubi.com
GUBI.COM
TECHNICAL INFORMATION
ENVERIOMENTAL PROTECTION
PROTECTION DE L’ENVIRONNEMENT
INFORMATIONS TECHNIQUES
Light sources: E26, 1100 Lumen (Max 12W LED). Turn power off when changing light bulb. Isolation class II. The lamp is
not approved for outdoor use in damp/wet rooms (IP20)
Electrical products must be thrown out with domestic waste. They must be taken to a communal collecting point for
environmentally friendly disposal in accordance with local regulations. Contact your local authorities or retailer for advice
on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and
make it available for recyclable material collection-service. Do not incinerate.
Les produits électriques doivent être jetés avec les ordures ménagères. Ils doivent être déposés dans un point de collecte
conformément aux réglementations en vigueur afin de respecter la protection de l’environnement. Pour toute information
sur le recyclage veuillez-vous renseigner auprès de votre commune. L’emballage est recyclable.
Pensez bien au tri. service de collecte de matériel. Ne pas incinerar.
Sources lumineuses: E26, 1100lumens (LED 12W max.). Couper l’alimentation lors du changement d’ampoule. Classe
d’isolement II. La lampe n’est pas homologuée pour une utilisation en extérieur dans des pièces humides (IP20)
CARE INSTRUCTIONS
MESURES D’ENTRETIEN
TROUBLESHOOTING
EN CAS DE PANNE
Daily cleaning can be done by wiping the frame with a clean dry cloth. Should the surface need more attention this can
be cleaned with water and a light detergent or soap applied with a damp cloth. Wipe after with a clean dry cloth. Avoid
any abrasive materials.
Le cadre doit être nettoyé à l’aide d’un chiffon propre et sec. Pour un nettoyage plus profond, utilisez de l’eau et un
détergent léger ou du savon et appliquer sur un chiffon humide puis essuyez à nouveau à l’aide d’un chiffon propre et
sec. Éviter les matériaux abrasifs.
If lamp does not light, turn off the power. Check the bulb for a broken filament. Replace bulb if necessary, then turn it on.
If the lamp still does not light, please contact customer service at the local dealer. If the external flexible cable or cord
of this lamp is damaged, it must be replaced by a qualified electrician in order to avoid a hazard.
Si la lampe ne s’allume pas, coupez l’alimentation. Vérifiez l’ampoule pour un filament cassé. Remplacez l’ampoule si
nécessaire, puis allumez-la. Si la lampe ne s’allume toujours pas, veuillez contacter le service client du revendeur local.
Si le câble flexible externe ou le cordon de cette lampe est endommagé, il doit être remplacé par un électricien qualifié
afin d’éviter tout danger.
174-20-001-02-Timberline_Assembly_Manual
ASSEMBLY INSTRUCTIONS
CONTENTS
x1 x1 x1 x1 x1 x1 x1x2
1.
Place the curved stem on the base
and fix them with the bolt (a), tightening it with the tool (b).
Placez la tige incurvée sur la base
et fixez-les avec le boulon (a), en le serrant avec l’outil (b).
2.
a) b)
a)
d)
e)
b)
c)
Take out the shade and the ring from package (a), unfold the shade (b), and click the five
hooks on the ring (c). It is recommended to carry out this operation in two.
Fix the shade with the lampshade holder internal ring (d).
Adjust the position of shade as you prefer (e).
Sortez l’abat-jour et l’anneau de l’emballage (a), dépliez l’abat-jour (b) et cliquez sur les cinq
crochets de l’anneau (c). Il est recommandé de réaliser cette opération en deux.
Fixez l’abat-jour avec la bague intérieure du porte-abat-jour (d).
Ajustez la position de l’abat-jour selon vos préférences (e).
  • Page 1 1
  • Page 2 2

GUBI Timberline Floor Lamp Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues