Bercomac C151 61676 3 _ C151 61677 3 Manuel utilisateur

1

OWNER’S

MANUAL

MODEL NO.

C 151 61676 3

C 151 61677 3

Caution:

Read and Follow

All Safety Rules

and Instructions

Before Operating

This Equipment

44" AND 48" NORTHEAST TWO

STAGE SNOWBLOWER FOR

CRAFTSMAN TRACTORS

·Assembly

·Operation

·Maintenance

·Repair Parts

Sears Canada, Inc., Toronto, Ontario M5B 2B8

104752 K-02

*104752*

2

LIMITED ONE (1) YEAR WARRANTY ON CRAFTSMAN

TRACTOR ATTACHMENTS "SNOWBLOWER"

For one (1) year from date of purchase, Sears Canada Inc. will repair or replace free of charge at Sears option any

parts which are defective as a result of defective material or faulty workmanship.

COMMERCIAL OR RENTAL USE:

Warranty on Tractor Attachments "Snowblower" used for commercial or rental purposes is limited to 90 days.

This warranty does NOT cover:

* Wear items, such as shear pins and shear bolts, belts

* Repairs due to customer abuse or neglect

* Pre-delivery set-up

* In Home service

Warranty service is available by returning the Craftsman Tractor Attachment to the nearest Sears Service Centre /

Department in Canada. This warranty applies only while this product is in use in Canada.

This warranty is in addition to any statutory warranty and does not exclude or limit legal rights you may have but shall

run concurrently with applicable provincial legislation. Furthermore, some provinces do NOT allow limitation on how

long an implied warranty will last so the above limitations may not apply to you.

SEARS CANADA INC., TORONTO, ONTARIO, M5B 2B8

FOR SERVICE PLEASE CALL

SEARS HOME CENTRAL

1-800-4-MY-HOME®

WARRANTY

1

INTRODUCTION ...................................................................................................................................... 2

SAFETY PRECAUTIONS ......................................................................................................................... 3

SAFETY DECALS ..................................................................................................................................... 5

ASSEMBLY

Tools Required ................................................................................................................ 6

Step 1: Tractor Preparation .......................................................................................................... 6

Step 2: Subframe Installation ....................................................................................................... 7

Step 3: Drive Mechanism Preparation ......................................................................................... 13

Step 4: Drive Mechanism Installation ........................................................................................... 17

Step 5: Snowblower Preparation ................................................................................................. 19

Step 6: Snowblower Installation ................................................................................................... 20

OPERATION

Snowblower Operation ................................................................................................................. 22

Controls ........................................................................................................................................ 22

Snow Removal ............................................................................................................................. 22

MAINTENANCE

Maintenance ................................................................................................................................ 23

Adjustments ................................................................................................................................. 23

Lubrication ................................................................................................................................... 23

Clearing a Clogged Discharge Chute .......................................................................................... 23

Cutting Edge Maintenance ........................................................................................................... 23

Auger and Fan Shear Bolt Replacement ..................................................................................... 23

End of Season Storage ................................................................................................................ 23

Belt Installation, Adjustment and Replacement ........................................................................... 24

DISMOUNTING

Snowblower Dismounting ............................................................................................................ 26

Drive Mechanism Dismounting .................................................................................................... 26

TROUBLESHOOTING .............................................................................................................................. 27

TORQUE SPECIFICATION TABLE .......................................................................................................... 29

PARTS BREAKDOWN & LISTS

Chute .......................................................................................................................................... 30

Northeast Drive Mechanism ......................................................................................................... 32

Subframe ..................................................................................................................................... 34

Snowblower ................................................................................................................................. 37

OPTIONS & ATTACHMENTS ............................................................................................... 41

CONSUMER INFORMATION .............................................................................................................................. 42

TABLE OF CONTENTS

Page

2

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your accessory.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use.

Carefully read, understand and follow these recommendations and insist that they be followed by those who will use

this accessory.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL

THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER,

WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD.

HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions are

not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not

followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are not

followed.

Record your accessory serial number and purchase date in the section reserved below. Your dealer requires this

information to give you prompt, efficient service when ordering replacement parts. Use only genuine parts when

replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

PURCHASE DATE : ___________________________

3

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the accessory’s

safety labels to warn of the possibility of serious

injury. Please take special care in reading and

understanding the safety precautions before

operating the vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before starting to clear snow.

7. Always wear safety glasses or eye shields during

operation or while performing an adjustment or

repairs to protect the eyes from foreign objects that

may be thrown from the accessory.

8. Never modify the accessory or any part without

the written consent from the manufacturer.

4

SAFETY PRECAUTIONS

OPERATION:

1. Do not put hands or feet near, under or inside

rotating parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine

(motor), disconnect the wire from the spark plug(s)

and keep wire away to prevent accidental starting.

Thoroughly inspect the accessory for any damage

and repair damage before restarting and using the

accessory.

4. If the unit should start to vibrate abnormally, stop

the engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when

starting the engine and for transporting in or out of

the building. Do not operate or let motor run in a

storage area without ventilation because gas

contains carbon monoxide which is odorless,

colorless and can cause death.

7. Never clean across the face of slopes, go from top

to bottom. Exercise extreme caution when using

equipment on slopes. Do not attempt to clear a

steep slope.

8. Never use an accessory without proper guards,

plates, or other safety protective devices in place

9. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

10.Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

11.Do not carry passengers.

12.Disengage power to the accessory when it is

transported or not in use.

WHENEVER YOU SEE THIS SYMBOL

IT MEANS:

WARNING!

BECOME ALERT !

YOUR SAFETY IS INVOLVED!

MAINTENANCE AND STORAGE

1.When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. Disconnect wire from the spark plug

(s) and keep wire away to prevent accidental

starting.

2. Check all the bolts at frequent intervals to make

sure that they are properly tightened .

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources

are present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6. For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter every

day. Clean it or replace it as necessary. Change the

oil more often when working in dusty conditions.

See the vehicle’s and accessory's owner’s manual.

13.Never operate the accessory without good visibility

or light.

14.Keep the accessory away from heat sources or

flames.

15.Always wear a dust mask when working in a dusty

environment.

5

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

Decal # 102125 Decal # 102126

Decal # 102127 Decal # 103951

Decal # 102124

Decal # 102128

6

ASSEMBLY

IMPORTANT: TORQUE ALL BOLTS ACCORDING

TO TORQUE SPECIFICATION TABLE (SEE TABLE

OF CONTENTS) WHEN STATED: TIGHTEN

FIRMLY. REFER TO PARTS BREAKDOWN

SECTION FOR PARTS IDENTIFICATION.

NOTE: This subframe was designed to fit various

models of tractors. Make sure to follow the

instructions that correspond to your tractor. The

VGT frame sometimes requires a particular

procedure.

This subframe may be used to install different

attachments (see attachments page). Once installed,

it may remain permanently on the tractor. Before

doing any modifications or installations on the tractor,

open the tractor hood, disconnect the headlights and

remove the hood. Disconnect the wire from the spark

plug(s) and keep away from spark plug(s) to prevent

accidental starting.

STEP 1

TRACTOR PREPARATION:

It is not necessary to remove mower deck at this step.

According to the model of the tractor, remove the mower

front attaching supports if they are bolted to the outside

of the tractor’s frame on each side.

In order to install the subframe’s supports, it may be

necessary to remove certain bolts or certain parts.

NOTE: Take note of the place and how the bolts and

parts were installed in order to reinstall them in the same

manner and place as before.

If applicable, make sure that the belt guide does not

touch any mobile part when reinstalled.

How to:

Take the right support (item 1) and place it on the right

side of the tractor’s frame.

Align the hole (item 2) on the right support with the hole

(item 3) which is about 2” (according to the model of the

tractor) from the edge of the tractor’s front frame.

Remove all the bolts and parts from the tractor’s frame

that will interfere with the installation of the right support.

Do the same operation on the left side with the left

support.

Align the holes in order to identify and remove the

bolts and/or parts that come into interference with the

support

View of VGT tractor frame

View of tractor frame

TOOLS REQUIRED

1 Square head screwdriver #2

2 Wrenches 3/8’’, 9/16’’

1 Ratchet

3 Sockets 7/16’’, 9/16’’, 1/2’’

1 extension for ratchet

7

ASSEMBLY

Install brace pin

STEP 2

SUBFRAME INSTALLATION:

For other tractors:

Use brace pin (item 4) and follow the

installation instructions below.

Install the brace pin (item 4) on the right support (item

2) with two carriage bolts 3/8’’ x 1’’ (item 3;heads

outside) and two 3/8" flange nuts.

Tighten firmly.

NOTE: Generally, the brace pin must be over the

lawnmower belt and at the same time, as low as

possible.

No interference is allowed.

See chart.

Tractor Hole

(inside view of item 2) Position of

brace pin

2006 and

2007

(most)

Bottom Upwards

VGT

frame Bottom Downwards

Others Top Upwards

or

downwards

You must choose which brace pin (item 1 or item 4)

that is appropriate for your tractor model.

Tractors with a clutch that measures 5.5”

high only (as shown):

You must use brace pin (item 1) and install it in the

bottom holes of the right support (item 2) with two

carriage bolts 3/8’’ x 1’’ (item 3;heads outside) and

two 3/8" flange nuts.

Tighten firmly.

NOTE: This brace pin must be under the lawnmower

belt.

The belt must not touch the brace pin.

8

RIGHT SUPPORT:

Install the right support (item 1) on the right side.

The chart identifies the hardware according to the

holes in the tractor’s frame. Even though some holes

may not exist on certain models of tractors, use the

maximum of holes & bolts possible to ensure the

solidity of the kit.

Carr. B. = Carriage bolt; head towards the inside.

Hex B. = Hexagonal bolt; head towards the outside.

N/A = Not applicable

Install right support .

ASSEMBLY

NOTES:

1. On new tractors, turning the wheels to the left will

facilitate installation.

2. The spacer (item 15) is used to strengthen

certain heat shields.

If necessary, slide the shim (item 14) between the

tractor frame (item 16) and the right support; in line

with hole (item 9 or item 11). (Make sure that the shim

stays perpendicular with the top of the support).

Do not tighten the screws or the nuts.

2 Carr. B 3/8 x 3/4’’

Flange nut 3/8’’ Thread cutting

screw 3/8 x 1’’

3 N/A Thread cutting

screw 3/8 x 1’’

4 N/A Thread cutting

screw 3/8 x 1’’

5 Carr. B. 5/16 x 1’’

Flange nut 5/16’’ N/A

6 N/A Thread cutting

screw 5/16 x 1’’

7, 9 Hex B. 3/8 x 1’’

Flange nut 3/8’’ N/A

10, 11 N/A Hex B. 3/8 x 1’’

12 Set screw 5/16 x 1/2’’

(on support for the

cab)

N/A

Item # If square holes on

tractor If threaded holes

on tractor

13 Tractor bolt and

Spacer (Round hole) N/A

8 Hex B. 3/8 x 1’’

Flange nut 3/8’’ Thread cutting

screw 3/8 x 1’’

9

ASSEMBLY

Install the left support and handle support

LEFT SUPPORT AND HANDLE SUPPORT:

Install the left support (item 1) and the handle support

(item 17). Secure the brace pin (item 19)

The chart identifies the hardware according to the

holes in the tractor’s frame. Even though some holes

may not exist on certain models of tractors, use the

maximum of holes & bolts possible to ensure the

solidity of the kit.

Carr. B. = Carriage bolt; head towards the inside.

Hex B. = Hexagonal bolt; head towards the outside,

except 14 & 16.

N/A = Not applicable.

NOTE:

1. On new tractors, turning the wheels to the right

will facilitate installation .

2. The spacer (item 15) is used to strengthen

certain heat shields.

2 Carr. B. 3/8 x 3/4’’

Flange nut 3/8’’ Thread cutting

screw 3/8 x 1’’

3 Hex. B. 3/8 x 1’’ Thread cutting

screw 3/8 x 1’’

4 N/A Thread cutting

screw 3/8 x 1’’

5 Carr. B. 5/16 x 1’’

Flange nut 5/16’’ N/A

6 N/A

Thread cutting

screw 5/16 x 1’’

7, 9 Hex. bolt 3/8 x 1’’

Flange nut 3/8’’ N/A

10, 11 Hex. B 3/8 x 1’’

Flange nut 3/8’’

(round holes)

N/A

12 Set screw 5/16 x 1/2’’

(on support for the cab) N/A

Item # If square holes

on tractor If threaded

holes on tractor

14, 16 Hex. B 3/8 x 1’’

Flange nut 3/8’’

(round holes)

N/A

18 Plastic grommet

(round hole in support) N/A

13 Tractor bolt and Spacer

(round holes) N/A

8 Hex. bolt 3/8 x 1’’

Flange nut 3/8’’ Thread cutting

screw 3/8 x 1’’

10

ASSEMBLY

Install the mower brackets inside the support and

other parts if applicable.

If necessary, slide the shim (item 20, previous page)

between the tractor frame and the support, in line with

hole (item 9 or item 11). (Make sure that the shim

stays perpendicular with the top of the support).

Slightly tighten the screws and bolts.

Make sure that the brace pin stays straight and does

not come into contact with any part of the tractor (ex:

the engine belt when mower deck is in raised

position).

If there is a contact, turn the brace pin upside down.

MOWER BRACKET

If you have removed the original supports from the

tractor, in order to install the mower brackets (item

19) (included in this kit) inside the support; insert two

hex. bolts 3/8 x 1 1/4" (item 20) (the heads on the

outside) in the top holes of the right support .

From the inside of the support, place the shim (item

21; notice orientation) and the mower bracket (item

19) on the bolts. Secure with two flange nuts.

Do the same operation on the left side.

Tighten firmly.

Reinstall the parts:

Reinstall the parts previously removed in their original

position.

11

ASSEMBLY

TRACTORS WITH A MANUAL CLUTCH

ACTIVATED BY A CABLE:

If it is not possible to put back in place the tractor’s

belt guides, use the replacement belt guides supplied.

Insert the collars (item 1) on the brace pin (item 4).

Tighten slightly. Place a belt guide (item 2) on each

collar. Secure with a #10 x 3/4" machine screw (item

3) and nylon insert lock nut.

The belt guides must not touch the belt (item 5) when

the drive mechanism is engaged.

When the drive mechanism is disengaged, the belt

guides (item 6) must push enough on the belt (item 7)

so that the drive mechanism pulley does not turn.

Tighten the collar screws and the nuts tightly.

WARNING

TO PREVENT INJURIES:

It is the person who installs the belt guides

responsibility to make sure that when the

lawnmower is disengaged that all moving parts

stop.

For more information, do not hesitate to contact

the technical support.

Install belt guide/drive mechanism engaged

Drive mechanism disengaged

12

ASSEMBLY

Assemble the lift arm

ASSEMBLY

Secure with the hair pin (item 3).

Tighten all the bolts.

If there is interference between the pivot support and

the tractor heat shield, replace with the heat shield

(item 4) supplied.

NOTE: If the original heat shield is bolted to the front

of tractor frame, detach the top part (item 6) of the

heat shield supplied by folding it up and down along

the dotted line.

Be careful not to cut yourself on the sharp edges. For

your safety sand down the sharp edges.

Use the tractor bolts to secure in place.

PIVOT SUPPORT:

Turn the front wheels towards the right.

Install the pivot support (item 1) between the two

supports and slide in place the pin (item 2) in the

required holes. The other holes get the hooked end

(item 5) of the pin. See table.

Install the pivot support.

Tires Holes in pivot support

15’’ x 6’’ or smaller Top

16’’ x 6.5’’ or bigger Bottom

LIFT ARM:

Insert the nylon bushings (item 1) in the lift arm (item

2).

Install the handgrip (item 3) on the lift arm as shown.

13

LIFT MECHANISM:

Slide the link (item 1) inside the box of the right

support (item 2). Insert the pin (item 3) inside the link.

Insert the lift arm (item 4) on the pin (item 5) of the

right support and on the pin (item 3).

Secure the arm with one washer (item 6) and one hair

pin 4 mm (item 7).

Secure the pin in place with a flat washer (item 8)

and a hair pin 2.5 mm (item 9, inserted from the

bottom to the top).

Secure the link to the pivot support (item 10) with a

pin (item 11) and a hair pin 2.5 mm (item 12).

Install the lift mechanism

ASSEMBLY

STEP 3

DRIVE MECHANISM PREPARATION:

SUPPORTS-GENERAL INSTALLATION:

Secure the left support (See table) with two carriage

bolts 3/8’’ x 3/4’’ (item 3) heads outside. Secure with

two flange nuts.

NOTE: Install only one support on the right side.

Side Support

Left 104345

(item 2)

Right

(If no interference with mower deck) 104345

(Item 2)

Right

(If 104345 interferes with mower deck) 104346

(item 1)

On the right side, install the mounting support (item 4)

inside the frame. Install on the outside (according to

chart) the support (item 1 or 2), two washers

7/16" (item 5) and secure with two hair pins (item 6).

NOTE:On certain models of tractors, when the mower

deck is lifted to its highest position, it comes into

contact with the right hand support.

This installation will allow to remove the supports very

easliy at the end of the season.

Install supports (General installation).

14

ASSEMBLY

NOTE: If a bracket is installed on the outside of the

lefthand side of the tractor frame:

1 Install the left support on the inside of the frame.

Secure both bracket and left support to frame using

hardware already mentionned.

2 Insert two flat washers 7/16’’ between the right

support and the frame, but only in this case.

SUPPORTS-VGT FRAME INSTALLATION:

To install the drive mechanism, you must remove the

two bolts from the footrests (from each side).

Secure the left support (item 2) (longest support with

point towards the front) and the right support (item 1)

(shortest support with point towards the front) with the

bolts removed from the footrests.

Install supports (VGT frame)

NOTE:

1) This drive mechanism may be mounted on tractors

with two types of clutch mechanisms. See the

following instructions on the next pages for those

that are appropriate for your tractor.

2) The mower deck must be removed to install / use

the drive mechanism.

NOTE: The drive mechanism must be straight, to

make sure the belt works well.

15

Tractor Position

2006 (most models, factory installed) A

VGT frame B

Others C

2007 (most models tractors) D

Place the support (item 1) in the required position

according to chart, secure with the bolts (item 3 )and

tighten firmly.

NOTE: For position D, use the shim (item 4) and two

1/4 x 3/4" hex bolts supplied in the hardware bag.

Remove the flat pulley (item 5). Turn upside down

and reposition the pulley as shown in A with the flat

washers.

Reinstall the spring (item 2) in its original place.

Remove and reinstall the spring

ASSEMBLY

Use the following instructions to reposition the

support (item 1) as needed.

To make the job easier, remove the spring (item 2).

Remove the support (item 1) by removing the two

hex. bolts 1/4’’ x 1/2’’ (item 3).

Reposition the support

Reposition the pulley

16

TRACTOR WITH AN ELECTRIC CLUTCH.

No modifications are needed.

TRACTORS WITH A MANUAL CLUTCH ACTI-

VATED BY A CABLE.

Remove the spring that is hooked in holes (item1) of

idler arm (item 2) and drive frame (item 10).

Hook the spring of the tractor’s cable (item 5) on the

tension arm.

Cut the tie wrap that holds the cable to the frame.

NOTE: Depending on the mower deck model, there

are different cable lengths. To determine where to

place the cable holder (item 7), hook the end of the

cable spring (item 5) on the idler arm (item 2). Slide

the cable shield (item 6) temporarily into the slot on

the cable holder (item 7). To identify into which

holes the cable holder will be bolted in, you must

apply a slight tension on the cable. This adjustment

must be done with the clutch arm in the disengaged

position.

Remove the cable shield and secure the cable

holder (item 7) on the frame using two 1/4 x 3/4"

hex bolts (item 8) and flange nuts.

Reinstall the cable shield into the cable holder and

secure with a 2mm hair pin (item 9).

Install cable holder

ASSEMBLY

17

ASSEMBLY

STEP 4

DRIVE MECHANISM INSTALLATION:

NOTE: You must remove mower deck to install

the drive mechanism.

Install the drive mechanism (item 1) by hooking the

front part of the drive frame (item 2) on the brace pin

(item 3).

Lift and attach the rear portion of the drive frame

between the supports (items 4 or 5 or 6) by inserting

a pin on each side. Select the correct holes using the

chart.

Install drive mechanism .

Adjust belt guides/ Drive mechanism engaged

(View of top of drive mechanism)

Support Holes

104345 right side Bottom

104346 left side Top

104093 & 104094 Only one possibility

Item #

4

6

5

TRACTOR WITH A MANUAL CLUTCH ACTIVATED

BY A CABLE

Readjust the belt-guides (item 2). If the belt guides

are not installed yet, refer to TRACTOR WITH A

MANUAL CLUTCH ACTIVATED BY A CABLE of

STEP 2

The belt guides (item 2) must not touch the belt (item

1) when the drive mechanism is engaged.

Secure with two 2.5 mm hair pins (item 7).

Install the belt (item 8) on the engine pulley and route

inside the belt guide (item 9).

WARNING

TO PREVENT INJURIES:

It is the person who installs the drive mechanism

responsibility to make sure that when the clutch

is disengaged that all moving parts stop.

For more information, do not hesitate to contact

the technical support.

18

ASSEMBLY

When the drive mechanism is disengaged, the belt

guides (item 4) must push enough on the belt (item 3)

so that the drive mechanism pulley does not turn.

Tighten the collar screw and the nut tightly.

WARNING

TO PREVENT INJURIES DO THIS VERIFICATION

WHEN THE ENGINE IS STOPPED.

NOTE: After installation, attach the cable to the frame

with the new tie wrap supplied with this kit.

Drive mechanism disengaged

BELT ALIGNMENT VERIFICATION:

Make sure the drive mechanism pulley (item 1) is

aligned with the engine pulley (item 2).

If not, you may change the position of the support

(104344) and / or the position of the rear pins as

needed.

If the top edge of the belt touches the edge of the flat

pulley (item 3), remove the flat washer (item 4).

NOTE:Electric Clutch :

If your tractor is equipped with an electric clutch,

make sure the spring is well inserted in its place and

the belt does not touch the belt guides at any point.

NOTE: Manual Clutch:

If your tractor is equipped with a manual clutch, make

sure the belt guide does not touch the belt at any

point while the drive mechanism is engaged .

La page charge ...

Bercomac C151 61676 3 _ C151 61677 3 Manuel utilisateur

Bercomac C151 61676 3 _ C151 61677 3 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents