Bosch GKS Professional Manuel utilisateur

Marque: Bosch

Modèle: GKS Professional

Taper: Manuel utilisateur

Robert Bosch Power Tools GmbH

70538 Stuttgart

GERMANY

www.bosch-pt.com

1 609 92A 5MD (2020.03) O / 149

en Original instructions

fr Notice originale

pt Manual original

es Manual original

pt Manual de instruções original

zh 正本使用明

zh 原始使用說明書

th 



id Petunjuk-Petunjuk untuk

Penggunaan Orisinal

vi Bn gc hng dn s dng

ar   

fa   

1 609 92A 5MD

GKS Professional

18V-68 GC I 18V-68 C

2 |

English ................................................... Page 7

Français .................................................. Page 19

Português .............................................. Página 31

Español ................................................ Página 42

Português do Brasil..................................... Página 54

 ....................................................... 66

.................................................. 75

......................................................  84

Bahasa Indonesia..................................... Halaman 96

Ting Vit ............................................... Trang 107

..................................................  119

 .................................................. 131

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

| 3

GKS 18V-68 GC

(20)

(22)

(2)

(1) (3)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(14)

(15)

(17)

(19)

(24)

(13)

(16)

(21)

(4)

(18)

GKS 18V-68 C

(1)

(2)

(4)(23)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(16)

(17)

(18) (19)

(20) (21)

(24)

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

4 |

GKS 18V-68 GC

A(30)

(25)

(26)

(29)

(27)

(28)

(31)

(10)

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

| 5

F G

(32)

(22)

(17)

(11)

(33)

(3)(40)

(39)

(38)

(37)

(34)

(35)

(36)

(18)

(13)

(6)

GKS 18V-68 GC GKS 18V-68 C

(23) (17)

GKS 18V-68 GC

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

6 |

(33)

(41)

(42)

(43)

(44)

(45)

GKS 18V-68 GC

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

English | 7

English

Safety instructions

General Power Tool Safety Warnings

WARNING Read all safety warnings, instruc-

tions, illustrations and specifica-

tions provided with this power tool. Failure to follow all in-

structions listed below may result in electric shock, fire and/

or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cord-

less) power tool.

Work area safety

uKeep work area clean and well lit. Cluttered or dark

areas invite accidents.

uDo not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust

or fumes.

uKeep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

Electrical safety

uPower tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

uAvoid body contact with earthed or grounded sur-

faces, such as pipes, radiators, ranges and refrigerat-

ors. There is an increased risk of electric shock if your

body is earthed or grounded.

uDo not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of elec-

tric shock.

uDo not abuse the cord. Never use the cord for carry-

ing, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric

shock.

uWhen operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suit-

able for outdoor use reduces the risk of electric shock.

uIf operating a power tool in a damp location is un-

avoidable, use a residual current device (RCD) protec-

ted supply. Use of an RCD reduces the risk of electric

shock.

Personal safety

uStay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inatten-

tion while operating power tools may result in serious per-

sonal injury.

uUse personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non-skid safety shoes, hard hat or hearing protection

used for appropriate conditions will reduce personal in-

juries.

uPrevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or en-

ergising power tools that have the switch on invites acci-

dents.

uRemove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal in-

jury.

uDo not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

uDress properly. Do not wear loose clothing or jew-

ellery. Keep your hair and clothing away from moving

parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

uIf devices are provided for the connection of dust ex-

traction and collection facilities, ensure these are con-

nected and properly used. Use of dust collection can re-

duce dust-related hazards.

uDo not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe in-

jury within a fraction of a second.

Power tool use and care

uDo not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was de-

signed.

uDo not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

uDisconnect the plug from the power source and/or re-

move the battery pack, if detachable, from the power

tool before making any adjustments, changing ac-

cessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

uStore idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

uMaintain power tools and accessories. Check for mis-

alignment or binding of moving parts, breakage of

parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

8 | English

uKeep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

uUse the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into ac-

count the working conditions and the work to be per-

formed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

uKeep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

Battery tool use and care

uRecharge only with the charger specified by the manu-

facturer. A charger that is suitable for one type of bat-

tery pack may create a risk of fire when used with another

battery pack.

uUse power tools only with specifically designated bat-

tery packs. Use of any other battery packs may create a

risk of injury and fire.

uWhen battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a fire.

uUnder abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally oc-

curs, flush with water. If liquid contacts eyes, addi-

tionally seek medical help. Liquid ejected from the bat-

tery may cause irritation or burns.

uDo not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

of injury.

uDo not expose a battery pack or tool to fire or excess-

ive temperature. Exposure to fire or temperature above

130°C may cause explosion.

uFollow all charging instructions and do not charge the

battery pack or tool outside the temperature range

specified in the instructions. Charging improperly or at

temperatures outside the specified range may damage

the battery and increase the risk of fire.

Service

uHave your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

uNever service damaged battery packs. Service of bat-

tery packs should only be performed by the manufacturer

or authorized service providers.

Safety instructions for circular saws

Cutting procedures

u DANGER: Keep hands away from cutting area and

the blade. Keep your second hand on auxiliary handle,

or motor housing. If both hands are holding the saw,

they cannot be cut by the blade.

uDo not reach underneath the workpiece. The guard

cannot protect you from the blade below the workpiece.

uAdjust the cutting depth to the thickness of the work-

piece. Less than a full tooth of the blade teeth should be

visible below the workpiece.

uNever hold the workpiece in your hands or across your

leg while cutting. Secure the workpiece to a stable

platform. It is important to support the work properly to

minimise body exposure, blade binding, or loss of con-

trol.

uHold the power tool by insulated gripping surfaces,

when performing an operation where the cutting tool

may contact hidden wiring. Contact with a "live" wire

will also make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

uWhen ripping always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces the

chance of blade binding.

uAlways use blades with correct size and shape (dia-

mond versus round) of arbour holes. Blades that do not

match the mounting hardware of the saw will run off-

centre, causing loss of control.

uNever use damaged or incorrect blade washers or

bolt. The blade washers and bolt were specially designed

for your saw, for optimum performance and safety of op-

eration.

Kickback causes and related warnings

- kickback is a sudden reaction to a pinched, jammed or mis-

aligned saw blade, causing an uncontrolled saw to lift up and

out of the workpiece toward the operator;

- when the blade is pinched or jammed tightly by the kerf

closing down, the blade stalls and the motor reaction drives

the unit rapidly back toward the operator;

- if the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top sur-

face of the wood causing the blade to climb out of the kerf

and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect operat-

ing procedures or conditions and can be avoided by taking

proper precautions as given below.

uMaintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line

with the blade. Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by the

operator, if proper precautions are taken.

uWhen blade is binding, or when interrupting a cut for

any reason, release the trigger and hold the saw mo-

tionless in the material until the blade comes to a com-

plete stop. Never attempt to remove the saw from the

work or pull the saw backward while the blade is in

motion or kickback may occur. Investigate and take cor-

rective actions to eliminate the cause of blade binding.

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

English | 9

uWhen restarting a saw in the workpiece, centre the

saw blade in the kerf so that the saw teeth are not en-

gaged into the material. If a saw blade binds, it may walk

up or kickback from the workpiece as the saw is restar-

ted.

uSupport large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the edge

of the panel.

uDo not use dull or damaged blades. Unsharpened or im-

properly set blades produce narrow kerf causing excess-

ive friction, blade binding and kickback.

uBlade depth and bevel adjusting locking levers must

be tight and secure before making the cut. If blade ad-

justment shifts while cutting, it may cause binding and

kickback.

uUse extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

Lower guard function

uCheck the lower guard for proper closing before each

use. Do not operate the saw if the lower guard does

not move freely and close instantly. Never clamp or tie

the lower guard into the open position.If the saw is ac-

cidentally dropped, the lower guard may be bent. Raise

the lower guard with the retracting handle and make sure

it moves freely and does not touch the blade or any other

part, in all angles and depths of cut.

uCheck the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

uThe lower guard may be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts”. Raise the lower guard by the retracting handle

and as soon as the blade enters the material, the lower

guard must be released.For all other sawing, the lower

guard should operate automatically.

uAlways observe that the lower guard is covering the

blade before placing the saw down on bench or

floor.An unprotected, coasting blade will cause the saw

to walk backwards, cutting whatever is in its path. Be

aware of the time it takes for the blade to stop after

switch is released.

Additional safety warnings

uDo not allow the chip ejector to come into contact with

your hands. You may be injured by rotating parts.

uDo not use the saw above the level of your head. Doing

so will mean you have inadequate control of the power

tool.

uUse suitable detectors to determine if there are hid-

den supply lines or contact the local utility company

for assistance. Contact with electric cables can cause

fire and electric shock. Damaging gas lines can lead to ex-

plosion. Breaking water pipes causes property damage.

uHold the power tool firmly with both hands and make

sure you have a stable footing. The power tool can be

more securely guided with both hands.

uDo not operate the power tool when stationary . It is

not suitable for operation with a saw table.

uWhen performing plunge cuts which are not right-

angled, secure the guide plate of the saw so that it will

not shift sideways.In the event of a sideways shift, the

saw blade may become jammed, which could lead to kick-

back.

uSecure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than by

hand.

uAlways wait until the power tool has come to a com-

plete stop before placing it down. The application tool

can jam and cause you to lose control of the power tool.

uDo not use HSS saw blades. Such saw blades can easily

break.

uDo not saw any ferrous metals. Hot chips may ignite the

dust extractor.

uWear a dust mask.

uIn case of damage and improper use of the battery, va-

pours may be emitted. The battery can set alight or ex-

plode. Ensure the area is well ventilated and seek medical

attention should you experience any adverse effects. The

vapours may irritate the respiratory system.

uDo not open the battery. There is a risk of short-circuit-

ing.

uThe battery can be damaged by pointed objects such

as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to

burn, smoke, explode or overheat.

uOnly use the battery with products from the manufac-

turer. This is the only way in which you can protect the

battery against dangerous overload.

Protect the battery against heat, e.g. against

continuous intense sunlight, fire, dirt, water

and moisture. There is a risk of explosion and

short-circuiting.

uCaution! When using the power tool with Bluetooth®, a

fault may occur in other devices and systems, aero-

planes and medical devices (e.g. pacemakers, hearing

aids). Also, damage to people and animals in the im-

mediate vicinity cannot be completely excluded. Do

not use the power tool with Bluetooth® in the vicinity of

medical devices, petrol stations, chemical plants,

areas with a potentially explosive atmosphere or in

blasting areas. Do not use the power tool with

Bluetooth® in aircraft. Avoid using the product near

your body for extended periods.

The Bluetooth® word mark and logos are registered trade-

marks owned by Bluetooth SIG, Inc. and any use of such

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

10 | English

marks by Robert Bosch Power Tools GmbH is under li-

cense.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-

structions may result in electric shock, fire

and/or serious injury.

Please observe the illustrations at the beginning of this oper-

ating manual.

Intended use

The power tool is intended for making straight cuts in wood

with and against the grain and mitre cuts in wood while rest-

ing firmly against the workpiece.

With the Bluetooth® Low Energy Module GCY42 inserted,

power tool data and settings can be transferred between the

power tool and a mobile device by means of Bluetooth® wire-

less technology.

Product features

The numbering of the product features refers to the diagram

of the power tool on the graphics page.

(1) Lock-off button for on/off switch

(2) On/off switch

(3) User interface A)

(4) Auxiliary handle

(5) Adjusting lever for mitre/bevel angle preselection

(6) Wing bolt for parallel guide

(7) Scale for mitre/bevel angles

(8) Cut mark 45° (0°on GKS18V-68GC)

(9) Cut mark 0° (45°on GKS18V-68GC)

(10) Spindle lock button

(11) Parallel guide

(12) Retracting blade guard

(13) Base plate

(14) Adjusting lever for retracting blade guard

(15) Wing bolt for mitre/bevel angle preselectionA)

(16) Protective guard

(17) Cutting depth scale

(18) Chip ejector

(19) BatteryB)

(20) Cover for GCY42 Bluetooth® Low Energy Module

(21) GCY42 Bluetooth® Low Energy ModuleB)

(22) Button for cutting depth preselectionA)

(23) Lever for cutting depth preselection

(24) Handle (insulated gripping surface)

(25) Saw spindle

(26) Mounting flange

(27) Circular saw bladeB)

(28) Clamping flange

(29) Clamping bolt with washer

(30) Battery release buttonB)

(31) Hex key

(32) Dust/chip boxB)

(33) Pair of screw clampsB)

(34) Battery charge indicator (user interface)A)

(35) ECO mode indicator (user interface)A)

(36) Button for speed preselection (user interface)A)

(37) Speed stage/mode indicator (user interface)A)

(38) Smartphone indicator (user interface)A)

(39) Power tool status indicator (user interface)A)

(40) Temperature indicator (user interface)A)

(41) Guide railB)

(42) Extraction hoseB)

(43) Connection pieceA)B)

(44) Groove for Bosch and Mafell guide rail systemsA)

(45) Groove for Festool and Makita guide rail systemsA)

A) only for GKS18V-68GC

B) Accessories shown or described are not included with the

product as standard. You can find the complete selection of

accessories in our accessories range.

Technical data

Hand-held circular saw GKS18V-68 GC GKS18V-68 C

Article number 3 601 FB5 1.. 3 601 FB5 0..

Rated voltage V= 18 18

No-load speedA) min–1 2500–5000 5000

Max. cutting depth

– at a 0° mitre/bevel angle mm 68 70

– at a 45° mitre/bevel angle mm 49.8 49.5

– at a 50° mitre/bevel angle mm 45.8 44.4

Spindle lock ● ●

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

English | 11

Hand-held circular saw GKS18V-68 GC GKS18V-68 C

Use with FSN guide rail system ● –

Base plate dimensions mm 206x346 177.5x329

Max. saw blade diameter mm 190 190

Min. saw blade diameter mm 184 184

Max. base blade thickness mm 2.0 2.0

Min. base blade thickness mm 1.0 1.0

Locating bore mm 20 20

Weight according to EPTA-Procedure 01:2014B) kg 4.7–5.5 4.4–5.2

Recommended ambient temperature during char-

ging

°C 0 to +35 0 to +35

Permitted ambient temperature during opera-

tionC) and during storage

°C –20 to +50 –20 to +50

Compatible rechargeable batteries GBA 18V...

ProCORE18V...

GBA 18V...

ProCORE18V...

Recommended rechargeable batteries for max-

imum performance

ProCORE18V... ≥5.5Ah ProCORE18V... ≥5.5Ah

Recommended chargers GAL 18...

GAX 18...

GAL 36...

GAL 18...

GAX 18...

GAL 36...

Data transmission

Bluetooth®Bluetooth®4.2

(Low Energy)D)

Bluetooth®4.2

(Low Energy)D)

Signal interval s 8 8

Max. signal rangeE) m 30 30

A) measured at 20-25°C with battery ProCORE18V 8.0Ah.

B) Depends on battery in use

C) Limited performance at temperatures <0°C

D) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.2) and support the Generic Access Profile

(GAP).

E) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-

ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).

Noise/Vibration Information

Noise emission values determined according to

EN62841-2-5.

Typically, the A-weighted noise level of the power tool is:

Sound pressure level 98dB(A); sound power level

109dB(A). Uncertainty K=3dB.

Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty K

determined according toEN62841-2-5:

Sawing wood: ah<2.5m/s2, K=1.5m/s2

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Fitting

uOnly use saw blades the maximum permitted speed of

which is higher than the no-load speed of the power

tool.

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

12 | English

Using the



® Low Energy Module

GCY42

Read the corresponding operating instructions for informa-

tion about the Bluetooth® Low Energy ModuleGCY42.

Battery Charging

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the battery

The battery (19) is equipped with two locking levels to pre-

vent the battery from falling out if the battery release button

(30) is pressed unintentionally. As long as the battery is in-

serted in the power tool, it is held in position by means of a

spring.

To remove the battery (19), press the release button (30)

and pull the battery to the rear and out of the power tool. Do

not use force to do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the

state of charge of the battery. For safety reasons, it is only

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

Note: The state of charge of the battery is also displayed on

the user interface (3) (see "Zustandsanzeigen", page15).

Battery model GBA 18V...

LEDs Capacity

3× continuous green light 60−100%

2× continuous green light 30−60%

LEDs Capacity

1× continuous green light 5−30%

1× flashing green light 0−5%

Battery model ProCORE18V...

LEDs Capacity

5× continuous green light 80−100%

4× continuous green light 60−80%

3× continuous green light 40−60%

2× continuous green light 20−40%

1× continuous green light 5−20%

1× flashing green light 0−5%

Inserting/changing the circular saw blade

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uWear protective gloves when fitting the saw blade.

Danger of injury when touching the saw blade.

uOnly use saw blades that match the specifications

given in this operating manual and that are tested and

marked in accordance with EN 847-1

uThe permitted speed of the application tool must be at

least equal to the maximum speed marked on the

power tool. If accessories run faster than their rated

speed, they may break and fly off.

uDo not use abrasive wheels as the application tool un-

der any circumstances.

Selecting the saw blade

You will find an overview of recommended saw blades at the

end of these operating instructions.

Removing the saw blade (see figure A)

To change tools, we recommend that you place the power

tool down on the front side of the motor housing.

– Press and hold the spindle lock button (10).

uDo not press the spindle lock button (10) while the

saw spindle is moving. The power tool may become

damaged if this happens.

– Use the hex key (31) to undo the clamping bolt (29) in ro-

tational direction .

– Swing the retracting blade guard (12) back and hold on

to it firmly.

– Remove the clamping flange (28) and the saw blade (27)

from the saw spindle (25).

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

English | 13

Fitting the saw blade (see figure A)

To change tools, we recommend that you place the power

tool down on the front side of the motor housing.

– Clean the saw blade (27) and all the clamping elements

to be fitted.

– Swing the retracting blade guard (12) back and hold on

to it firmly.

– Place the saw blade (27) on the mounting flange (26).

The cutting direction of the teeth (direction of the arrow

on the saw blade) must match the rotational direction of

the arrow on the retracting blade guard (12).

– Attach the clamping flange (28) and screw in the clamp-

ing bolt (29) in rotational direction . Ensure that the

mounting flange (26) and clamping flange (28) are in-

stalled in the correct position.

– Press and hold the spindle lock button (10).

– Use the hex key (31) to tighten the clamping bolt (29) in

rotational direction . The tightening torque should be

6–9Nm, which corresponds to hand-tight plus ¼ turn.

Dust/chip extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Chip ejector (see figureB)

The chip ejector (18) can turn freely.

An extraction hose with a diameter of 35mm or a dust/chip

box (32) can be connected to the chip ejector (18).

To ensure optimum extraction, the chip ejector (18) must be

cleaned regularly.

External dust extraction

Connect the extraction hose (42) to a dust extractor (ac-

cessory). You will find an overview of connecting to various

dust extractors at the end of these operating instructions.

The power tool can be directly connected to the socket of a

Bosch all-purpose dust extractor with remote starter. This

dust extractor is started up automatically when the power

tool is switched on.

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Operation

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Operating modes

uRemove the battery before carrying out any work on

the power tool.

Setting the cutting depth (seefiguresD–E)

uAdapt the cutting depth to the thickness of the work-

piece. A space of less than the height of one full tooth

should be visible under the workpiece.

GKS 18V-68 GC

The cutting depth can be set using the button for cutting

depth preselection(22).

GKS 18V-68 C

The cutting depth can be set using the lever for cutting depth

preselection(23).

For a smaller cutting depth, pull the saw away from the base

plate(13); for a larger cutting depth, push the saw towards

the base plate(13). Set the required cutting depth on the

scale(17).

Adjusting the mitre/bevel angle

We recommend that you place the power tool down on the

front side of the protective guard (16).

GKS 18V-68 GC

Loosen the adjusting lever for mitre/bevel angle preselection

(5) and the wing bolt (15). Swivel the saw to the side. Set

the required mitre angle on the scale (7). Retighten the ad-

justing lever (5) and the wing bolt (15).

Note: When making mitre cuts, the cutting depth is less than

the value shown on the cutting depth scale (17).

GKS 18V-68 C

Loosen the adjusting lever for mitre/bevel angle preselec-

tion(5). Swivel the saw to the side. Set the required mitre/

bevel angle on the scale(7). Screw the adjusting lever(5)

back on again.

Note: When making mitre cuts, the cutting depth is less than

the value shown on the cutting depth scale (17).

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

14 | English

Cut Marks

GKS 18V-68 GC

0 45

045

The 0° cut mark(8) indicates the position of the saw blade

when making a right-angled cut. The 45° cut mark(9) indic-

ates the position of the saw blade when making a 45° cut.

For a precise cut, place the circular saw against the work-

piece as shown in the figure. We recommend making a test

cut.

GKS 18V-68 C

045

0 45

The 0° cut mark(9) indicates the position of the saw blade

when making a right-angled cut. The 45° cut mark(8) indic-

ates the position of the saw blade when making a 45° cut.

For a precise cut, place the circular saw against the work-

piece as shown in the figure. We recommend making a test

cut.

Using the FSN Guide Rail System

GKS 18V-68 GC

When using the FSN guide rail system, the power tool can

stay in the holder for the guide rail when making mitre cuts.

(8)

Use only cut marks (8) when

making a right-angled cut

and a 45º cut with the guide

rail.

Start-up

Inserting the battery

Push the charged battery (19) into the power tool until the

battery is securely locked.

Switching on/off

To start the power tool, first press the lock-off switch (1),

then press and hold the on/off switch (2).

To switch off the power tool, release the on/off switch (2).

Note: For safety reasons, the on/off switch (2) cannot be

locked; it must remain pressed during the entire operation.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharge

by the Electronic Cell Protection (ECP). When the battery is

discharged, the power tool is switched off by means of a pro-

tective circuit: The application tool no longer rotates.

ECO Mode

GKS 18V-68 GC

If the power tool is operated in the energy-saving ECO mode,

the battery life may be up to 30 % longer.

If the ECO mode is active, the symbol E is shown on the

speed setting/mode indicator (37).

User Interface (see figure C)

GKS 18V-68 GC

The user interface (3) is used to preselect the speed and to

indicate the status of the power tool.

Speed preselection

GKS 18V-68 GC

Six speed settings and the ECO mode are preset in the basic settings. Using a special application (Bosch Toolbox app), two to

six speed settings can be programmed.

The information in the table below describes the preset speeds (default settings) for each programmed number of levels.

Basic speed setting at level

1 2 3 4 5 6

[min-1] [min-1] [min-1] [min-1] [min-1] [min-1]

Number of speed settings

ECO 3630A) – – – – –

22500 5000 – – – –

32500 3800 5000 – – –

42500 3300 4200 5000 – –

52500 3100 3800 4400 5000 –

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

English | 15

Basic speed setting at level

1 2 3 4 5 6

[min-1] [min-1] [min-1] [min-1] [min-1] [min-1]

Number of speed settings

62500 3000 3500 4000 4500 5000

A) ±25%

You can use the button for speed preselection (36) to preselect the required speed, even during operation.

Status indications

GKS 18V-68 GC

Battery charge indicator

(user interface)(34) Meaning/cause Solution

Green (2 to 5 bars) Battery charged –

Yellow (1 bar) Battery almost empty Replace or charge battery soon

Red (1 bar) Battery empty Replace or charge battery

Temperature indicator (40) Meaning/cause Solution

Yellow Critical temperature has been reached (mo-

tor, electronics, battery)

Run the power tool at no load and allow it to

cool down

Red Power tool is overheated and will switch off Leave the power tool to cool down

Smartphone indicator(38)

and Power tool status indic-

ator (39)

Meaning/cause Solution

Yellow Service reminder For more information see Bosch Toolbox App

or Service

Power tool status indic-

ator(39) Meaning/cause Solution

Green Status OK –

Yellow Critical temperature has been reached or bat-

tery is almost empty

Run the power tool at no load and allow it to

cool down, or replace or charge the battery

soon

Red Power tool is overheated or battery is empty Allow the power tool to cool down, or replace

or charge the battery

Flashing red Restart protection is triggered Turn the power tool off and on again; if neces-

sary, remove the battery and reinsert it.

Connectivity functions

GKS 18V-68 GC

In conjunction with the Bluetooth® Low Energy Module

GCY42, the following connectivity functions are available

for the power tool:

– Registration and personalisation

– Status check, output of warning messages

– General information and settings

– Management

– Setting the speed levels

The smartphone indicator(38) lights up if the power tool

sends information (e.g.a temperature warning) to a mobile

device via Bluetooth® wireless technology.

Read the corresponding operating instructions for informa-

tion about the Bluetooth® Low Energy ModuleGCY42.

GKS 18V-68 C

In conjunction with the Bluetooth® Low Energy Mod-

uleGCY42, the following connectivity functions are avail-

able for the power tool:

– Registration and personalisation

– Status check, output of warning messages

– General information

– Management

Read the corresponding operating instructions for informa-

tion about the Bluetooth® Low Energy ModuleGCY42.

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

16 | English

Practical advice

uWith the Bluetooth® Low Energy Module GCY 42, the

power tool is equipped with a radio interface. Local

operating restrictions, e.g. in aircraft or hospitals,

must be observed.

uIn areas where the Bluetooth® wireless technology is

not allowed to be used, the Bluetooth® Low Energy

Module GCY42 and the button cell must be removed.

The width of cut varies depending on the saw blade used.

Protect saw blades against shock and impact.

Guide the power tool evenly, pushing it gently in the cutting

direction. Applying too much pressure to the power tool

when moving it in the cutting direction significantly reduces

the service life of the application tools and can damage the

power tool.

The sawing performance and the quality of the cut essen-

tially depend on the condition and the tooth shape of the

saw blade. This is why you should only use sharp saw blades

that are suitable for the material being machined.

Sawing wood

Choosing the right saw blade depends on the wood type,

wood quality and whether cuts with or against the grain are

required.

Making cuts in spruce with the grain produces long, spiral-

shaped chips.

Beech and oak dust is especially detrimental to health.

Therefore, work only with dust extraction.

Sawing with a parallel guide (see figure F)

The parallel guide (11) allows you to make precise cuts

along the edge of a workpiece and cut strips with the same

dimensions.

Slide the guide rod of the parallel guide (11) through the

guide into the base plate (13). Mount the parallel guide (11)

with the wing bolt (6).

Sawing with an auxiliary guide (see figure G)

For working on large workpieces or for cutting straight

edges, you can securely fasten a board or rail to the work-

piece as an auxiliary guide. The circular saw can be guided

along the path of this auxiliary guide with the base plate.

Sawing with the guide rail (see figures H – I)

GKS 18V-68 GC

You can use the guide rail (41) to produce straight cuts.

The adhesive layer prevents the guide rail from slipping and

preserves the surface of the workpiece. The guide rail's coat-

ing allows the power tool to glide more easily.

Place the circular saw directly on the guide rail (41). Fasten

the guide rail (41) to the workpiece using suitable clamping

devices, e.g. screw clamps, so that the narrow side of the

guide rail (41) is facing the saw blade.

The guide rail (41) must not protrude over the edge of

the workpiece being sawn into.

Switch on the power tool and push it gently in the cutting dir-

ection, guiding it evenly.

The connector (43) can be used to join two guide rails. The

four screws in the connector are used for the purpose of

clamping.

The groove (44) is suitable for guide rail systems from Bosch

and Mafell.

The groove (45) is suitable for guide rail systems from Fes-

tool and Makita.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of −20 to

50°C. Do not leave the battery in your car in the summer, for

example.

Occasionally clean the ventilation slots on the battery using a

soft brush that is clean and dry.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

The retracting blade guard must always be able to move

freely and retract automatically. It is therefore important to

keep the area around the retracting blade guard clean at all

times. Remove dust and chips with a paintbrush.

Non-coated saw blades can be protected against corrosion

using a thin layer of acid-free oil. Remove the oil again before

sawing as failure to do so will stain the wood.

Resin or glue residue on the saw blade has a detrimental ef-

fect on the quality of the cut. You should therefore clean saw

blades straight after use.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

Cambodia

Robert Bosch (Cambodia) Co., Ltd

Unit 8BC, GT Tower, 08th Floor, Street 169,

Czechoslovakia Blvd, Sangkat Veal Vong

Khan 7 Makara, Phnom Penh

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

English | 17

VAT TIN: 100 169 511

Tel.: +855 23 900 685

Tel.: +855 23 900 660

www.bosch.com.kh

People’s Republic of China

China Mainland

Bosch Power Tool (China) Co. Ltd.

Bosch Service Center

567, Bin Kang Road

Bin Kang District

Hangzhou, Zhejiang Province

China 310052

Tel.: (0571) 8887 5566 / 5588

Fax: (0571) 8887 6688 x 5566# / 5588#

E-Mail: [email protected]

www.bosch-pt.com.cn

HK and Macau Special Administrative Regions

Robert Bosch Co. Ltd.

21st Floor, 625 King’s Road

North Point, Hong Kong

Customer Service Hotline: +852 2101 0235

Fax: +852 2590 9762

E-Mail: [email protected]

www.bosch-pt.com.hk

India

Bosch Service Center

69, Habibullah Road, (Next to PSBB School), T. Nagar

Chennai–600077

Phone: (044) 64561816

Bosch Service Center

18, Community Center

Phase 1, Mayapuri

New Delhi–110064

Phone: (011) 43166190

Indonesia

PT Robert Bosch

Palma Tower 10th Floor

Jalan RA Kartini II-S Kaveling 6

Pondok Pinang, Kebayoran Lama

Jakarta Selatan 12310

Tel.: (21) 3005-5800

www.bosch-pt.co.id

Malaysia

Robert Bosch Sdn. Bhd.(220975-V) PT/SMY

No. 8A, Jalan 13/6

46200 Petaling Jaya

Selangor

Tel.: (03) 79663194

Toll-Free: 1800 880188

Fax: (03) 79583838

E-Mail: [email protected]

www.bosch-pt.com.my

Pakistan

Robert Bosch Middle East FZE – Pakistan Liaison Office

2nd Floor Plaza # 10, CCA Block, DHA Phase 5

Lahore, 54810

Phone: +92(303)4444311

Email: [email protected]

Philippines

Robert Bosch, Inc.

11th Floor Ten West Campus

20 LeGrand Ave., McKinley West

Fort Bonifacio, Taguig City 1634

Tel.: (+632) 8703871

www.bosch-pt.com.ph

Singapore

Powerwell Service Centre Ptd Ltd

Bosch Authorised Service Centre (Power Tools)

4012 Ang Mo Kio Ave 10, #01-02 TECHplace

Singapore 569628

Tel.: 6452 1770

Fax: 6452 1760

E-Mail: [email protected]

www.powerwellsc.com

www.bosch-pt.com.sg

Thailand

Robert Bosch Ltd.

FYI Center Tower 1, 5th Floor,

2525 Rama IV Road, Klongtoei,

Bangkok 10110

Tel.: 02 0128888

Fax: 02 0645802

www.bosch.co.th

Bosch Service – Training Centre

La Salle Tower Ground Floor Unit No.2

10/11 La Salle Moo 16

Srinakharin Road

Bangkaew, Bang Plee

Samutprakarn 10540

Tel.: 02 7587555

Fax: 02 7587525

Vietnam

Branch of Bosch Vietnam Co., Ltd in HCMC

14th floor, Deutsches Haus, 33 Le Duan

Ben Nghe Ward, District 1, Ho Chi Minh City

Tel.: (028) 6258 3690

Fax: (028) 6258 3692 - 6258 3694

Hotline: (028) 6250 8555

Email: [email protected]

www.bosch-pt.com.vn

Bahrain

EA Juffali and Brothers for Technical Equipment Company.

Kingdom of Bahrain, Al Aker - Block 0624 - Road 2403 -

Building 0055D

Phone: +97317704537

Fax: +973177045257

Email: [email protected]

Egypt

RBEG-LLC

22 Kamal Eldin Hussein

Sheraton Heliopolis

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

18 | English

11799 Cairo

E-mail: [email protected]

Iran

Robert Bosch Iran

3rd Floor, No 3, Maadiran Building

Aftab St., Khodami St., Vanak Sq.

Tehran 1994834571

Phone: +9821- 86092057

Iraq

Sahba Technology Group

Al Muthana airport road

Baghdad

Phone Bagdad: +964 (0) 7 901 930366

Phone Dubai: +971 (0) 4 422 1898

Email: [email protected]

Jordan

Roots Arabia – Jordan

Al-Hurriyah Street, Al-Muqabalein

Amman 11623, Jordan

P.O. Box: 110068

Tel. : +962 6 4398990

E-mail: [email protected]

Kuwait

Shuwaikh Industrial Area, Block 1, Plot 16, Street 3rd

P.O. Box 164 – Safat 13002

Phone: +965 - 2496 88 88

Fax: +965 - 2481 08 79

E-mail: [email protected]

Lebanon

Tehini Hana & Co. S.A.R.L.

P.O. Box 90-449

Jdeideh 1202 2040

Dora-Beirut

Phone: +9611255211

Email: [email protected]

Libya

El Naser for Workshop Tools

Swanee Road, Alfalah Area

Tripoli

Phone: +218 21 4811184

Oman

Malatan Trading & Contracting LLC

P.O. Box 131, Ruwi, Muscat

Postal Code: 112, Sultanate of Oman

Phone: +968 2479 4035/4089/4901

Mob: +968-91315465

Fax: +968 2479 4058

E-Mail: [email protected]

Qatar

International Construction Solutions W L L

P. O. Box 51, Doha

Phone: +974 40065458

Fax: +974 4453 8585

Email: [email protected]

Saudi Arabia

Juffali Technical Equipment Co. (JTECO)

P.O.Box: 1049 – Jeddah 21431 – KSA

Jeddah: 00966(0)126920770 – Ext433

Riyadh: 00966(0)114093976 – Ext-30/34/39

Dammam: 00966(0)138339565

E-mail: [email protected]

Syria

Dallal Establishment for Power Tools

Damascus. Baramkeh street - Ibn Amer street,

Phone: +963112241006 or 009631122414009

Mobile: 00963991141005

Email: [email protected]

United Arab Emirates

Central Motors & Equipment,

P.O. Box 26255, Dubai

Dubai: 00971(0)43090920/3090930

Abu Dhabi: 00971(0)24017745

Sharjah: 00971(0)65932777

Al Ain: 00971(0)37157419

E- Mail: [email protected]

Yemen

Abu Alrejal Trading Corporation

P.O. Box : 17024 , Zubeiry St.

Sana'a, Yemen

Tel: +967-1-20 20 10

Fax: +967-1-47 19 17

E-mail: [email protected]/[email protected]

Ethiopia

Forever plc

Kebele 2,754, BP 4806,

Addis Ababa

Phone: +251 111 560 600

Email: [email protected]

Ghana

Robert Bosch Ghana Limited

21 Kofi Annan Road Airport Residential Area Accra

Tel. +233(0)302794616

Kenya

Robert Bosch East Africa Ltd

Mpaka Road P.O. Box 856

00606 Nairobi

Nigeria

Robert Bosch Nigeria Ltd.

52–54 Isaac John Street P.O. Box

GRA Ikeja – Lagos

Tanzania

Diesel & Autoelectric Service Ltd.

117 Nyerere Rd., P.O. Box 70839

Vingunguti 12109, Dar Es Salaam

Phone: +255 222 861 793/794

Myanmar

Asia Era Company Limited

No.(40/44), Parami Road, 4th Quarter,South Okkalapa Tsp,

Yangon, Myanmar

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

Français | 19

Republic of South Africa

Customer service

Hotline: (011) 6519600

Gauteng – BSC Service Centre

35 Roper Street, New Centre

Johannesburg

Tel.: (011) 4939375

Fax: (011) 4930126

E-Mail: [email protected]

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street

Pinetown

Tel.: (031) 7012120

Fax: (031) 7012446

E-Mail: [email protected]

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: (021) 5512577

Fax: (021) 5513223

E-Mail: [email protected]

Bosch Headquarters

Midrand, Gauteng

Tel.: (011) 6519600

Fax: (011) 6519880

E-Mail: [email protected]

Transport

The contained lithium-ion batteries are subject to the Dan-

gerous Goods Legislation requirements. The batteries are

suitable for road-transport by the user without further re-

strictions.

When shipping by third parties (e.g.: by air transport or for-

warding agency), special requirements on packaging and la-

belling must be observed. For preparation of the item being

shipped, consulting an expert for hazardous material is re-

quired.

Dispatch battery packs only when the housing is undam-

aged. Tape or mask off open contacts and pack up the bat-

tery in such a manner that it cannot move around in the

packaging. Please also observe the possibility of more de-

tailed national regulations.

Disposal

Power tools, rechargeable batteries, accessor-

ies and packaging should be sorted for environ-

mental-friendly recycling.

Do not dispose of power tools and batteries/re-

chargeable batteries into household waste!

Battery packs/batteries:

Li-ion:

Please observe the notes in the section on transport (see

"Transport", page19).

Français

Consignes de sécurité

Avertissements de sécurité généraux pour l’outil

électrique

AVERTISSE-

MENT

Lire tous les avertissements de sé-

curité, les instructions, les illustra-

tions et les spécifications fournis

avec cet outil électrique. Ne pas suivre les instructions

énumérées ci-dessous peut provoquer un choc électrique,

un incendie et/ou une blessure sérieuse.

Conserver tous les avertissements et toutes les instruc-

tions pour pouvoir s'y reporter ultérieurement.

Le terme "outil électrique" dans les avertissements fait réfé-

rence à votre outil électrique alimenté par le secteur (avec

cordon d’alimentation) ou votre outil électrique fonctionnant

sur batterie (sans cordon d’alimentation).

Sécurité de la zone de travail

uConserver la zone de travail propre et bien éclairée.

Les zones en désordre ou sombres sont propices aux ac-

cidents.

uNe pas faire fonctionner les outils électriques en at-

mosphère explosive, par exemple en présence de li-

quides inflammables, de gaz ou de poussières. Les ou-

tils électriques produisent des étincelles qui peuvent en-

flammer les poussières ou les fumées.

uMaintenir les enfants et les personnes présentes à

l’écart pendant l’utilisation de l’outil électrique. Les

distractions peuvent vous faire perdre le contrôle de l’ou-

til.

Sécurité électrique

uIl faut que les fiches de l’outil électrique soient adap-

tées au socle. Ne jamais modifier la fiche de quelque

façon que ce soit. Ne pas utiliser d’adaptateurs avec

des outils électriques à branchement de terre. Des

fiches non modifiées et des socles adaptés réduisent le

risque de choc électrique.

uÉviter tout contact du corps avec des surfaces reliées

à la terre telles que les tuyaux, les radiateurs, les cui-

sinières et les réfrigérateurs. Il existe un risque accru

de choc électrique si votre corps est relié à la terre.

uNe pas exposer les outils électriques à la pluie ou à des

conditions humides. La pénétration d‘eau à l’intérieur

d’un outil électrique augmente le risque de choc élec-

trique.

uNe pas maltraiter le cordon. Ne jamais utiliser le cor-

don pour porter, tirer ou débrancher l’outil électrique.

Maintenir le cordon à l’écart de la chaleur, du lubri-

fiant, des arêtes vives ou des parties en mouvement.

Des cordons endommagés ou emmêlés augmentent le

risque de choc électrique.

uLorsqu’on utilise un outil électrique à l’extérieur, utili-

ser un prolongateur adapté à l’utilisation extérieure.

Bosch Power Tools 1 609 92A 5MD | (19.03.2020)

20 | Français

L’utilisation d’un cordon adapté à l’utilisation extérieure

réduit le risque de choc électrique.

uSi l'usage d'un outil électrique dans un emplacement

humide est inévitable, utiliser une alimentation proté-

gée par un dispositif à courant différentiel résiduel

(RCD). L'usage d'un RCD réduit le risque de choc élec-

trique.

Sécurité des personnes

uRester vigilant, regarder ce que vous êtes en train de

faire et faire preuve de bon sens dans votre utilisation

de l’outil électrique. Ne pas utiliser un outil électrique

lorsque vous êtes fatigué ou sous l’emprise de

drogues, de l’alcool ou de médicaments. Un moment

d’inattention en cours d’utilisation d’un outil électrique

peut entraîner des blessures graves.

uUtiliser un équipement de protection individuelle.

Toujours porter une protection pour les yeux. Les

équipements de protection individuelle tels que les

masques contre les poussières, les chaussures de sécuri-

té antidérapantes, les casques ou les protections audi-

tives utilisés pour les conditions appropriées réduisent

les blessures.

uÉviter tout démarrage intempestif. S’assurer que l’in-

terrupteur est en position arrêt avant de brancher

l’outil au secteur et/ou au bloc de batteries, de le ra-

masser ou de le porter. Porter les outils électriques en

ayant le doigt sur l’interrupteur ou brancher des outils

électriques dont l’interrupteur est en position marche est

source d’accidents.

uRetirer toute clé de réglage avant de mettre l’outil

électrique en marche. Une clé laissée fixée sur une par-

tie tournante de l’outil électrique peut donner lieu à des

blessures.

uNe pas se précipiter. Garder une position et un équi-

libre adaptés à tout moment. Cela permet un meilleur

contrôle de l’outil électrique dans des situations inatten-

dues.

uS’habiller de manière adaptée. Ne pas porter de vête-

ments amples ou de bijoux. Garder les cheveux et les

vêtements à distance des parties en mouvement. Des

vêtements amples, des bijoux ou les cheveux longs

peuvent être pris dans des parties en mouvement.

uSi des dispositifs sont fournis pour le raccordement

d’équipements pour l’extraction et la récupération des

poussières, s’assurer qu’ils sont connectés et correc-

tement utilisés. Utiliser des collecteurs de poussière

peut réduire les risques dus aux poussières.

uRester vigilant et ne pas négliger les principes de sé-

curité de l'outil sous prétexte que vous avez l'habitude

de l'utiliser. Une fraction de seconde d'inattention peut

provoquer une blessure grave.

Utilisation et entretien de l’outil électrique

uNe pas forcer l’outil électrique. Utiliser l’outil élec-

trique adapté à votre application. L’outil électrique

adapté réalise mieux le travail et de manière plus sûre au

régime pour lequel il a été construit.

uNe pas utiliser l’outil électrique si l’interrupteur ne

permet pas de passer de l’état de marche à arrêt et in-

versement. Tout outil électrique qui ne peut pas être

commandé par l’interrupteur est dangereux et il faut le ré-

parer.

uDébrancher la fiche de la source d’alimentation et/ou

enlever le bloc de batteries, s'il est amovible, avant

tout réglage, changement d’accessoires ou avant de

ranger l’outil électrique. De telles mesures de sécurité

préventives réduisent le risque de démarrage accidentel

de l’outil électrique.

uConserver les outils électriques à l’arrêt hors de la

portée des enfants et ne pas permettre à des per-

sonnes ne connaissant pas l’outil électrique ou les pré-

sentes instructions de le faire fonctionner. Les outils

électriques sont dangereux entre les mains d’utilisateurs

novices.

uObserver la maintenance des outils électriques et des

accessoires. Vérifier qu’il n’y a pas de mauvais aligne-

ment ou de blocage des parties mobiles, des pièces

cassées ou toute autre condition pouvant affecter le

fonctionnement de l’outil électrique. En cas de dom-

mages, faire réparer l’outil électrique avant de l’utili-

ser. De nombreux accidents sont dus à des outils élec-

triques mal entretenus.

uGarder affûtés et propres les outils permettant de

couper. Des outils destinés à couper correctement en-

tretenus avec des pièces coupantes tranchantes sont

moins susceptibles de bloquer et sont plus faciles à

contrôler.

uUtiliser l’outil électrique, les accessoires et les lames

etc., conformément à ces instructions, en tenant

compte des conditions de travail et du travail à réali-

ser. L’utilisation de l’outil électrique pour des opérations

différentes de celles prévues peut donner lieu à des situa-

tions dangereuses.

uIl faut que les poignées et les surfaces de préhension

restent sèches, propres et dépourvues d'huiles et de

graisses. Des poignées et des surfaces de préhension

glissantes rendent impossibles la manipulation et le

contrôle en toute sécurité de l'outil dans les situations in-

attendues.

Utilisation des outils fonctionnant sur batteries et

précautions d’emploi

uNe recharger qu’avec le chargeur spécifié par le fabri-

cant. Un chargeur qui est adapté à un type de bloc de

batteries peut créer un risque de feu lorsqu’il est utilisé

avec un autre type de bloc de batteries.

uN’utiliser les outils électriques qu’avec des blocs de

batteries spécifiquement désignés. L’utilisation de tout

autre bloc de batteries peut créer un risque de blessure et

de feu.

uLorsqu’un bloc de batteries n’est pas utilisé, le mainte-

nir à l’écart de tout autre objet métallique, par

exemple trombones, pièces de monnaie, clés, clous,

vis ou autres objets de petite taille qui peuvent donner

1 609 92A 5MD | (19.03.2020) Bosch Power Tools

La page charge ...

Bosch GKS Professional Manuel utilisateur

Marque: Bosch

Modèle: GKS Professional

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

português: Bosch GKS Professional Manual do usuário
日本語: Bosch GKS Professional ユーザーマニュアル

Documents connexes

Autres documents

Bosch Power Tools GmbH GDR GDX Manuel utilisateur