Grundfos MQ 3-35 Guide d'installation

GRUNDFOS INSTRUCTIONS

MQ

Installation and operating instructions

US

C

2

3

Table of contents

MQ

English (US)

Installation and operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Español (MX)

Instrucciones de instalación y operación. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Français (CA)

Notice d'installation et de fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Appendix 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

4

English (US)

English (US) Installation and operating instructions

Original installation and operating instructions.

CONTENTS

Page

1. Limited warranty

Products manufactured by GRUNDFOS PUMPS

CORPORATION (Grundfos) are warranted to the

original user only to be free of defects in material and

workmanship for a period of 24 months from date of

installation, but not more than 30 months from date

of manufacture. Grundfos' liability under this

warranty shall be limited to repairing or replacing at

Grundfos' option, without charge, F.O.B.

Grundfos' factory or authorized service station, any

product of Grundfos' manufacture. Grundfos will not

be liable for any costs of removal, installation,

transportation, or any other charges which may arise

in connection with a warranty claim. Products which

are sold but not manufactured by Grundfos are

subject to the warranty provided by the manufacturer

of said products and not by Grundfos' warranty.

Grundfos will not be liable for damage or wear to

products caused by abnormal operating conditions,

accident, abuse, misuse, unauthorized alteration or

repair, or if the product was not installed in

accordance with Grundfos' printed installation and

operating instructions.

To obtain service under this warranty, the defective

product must be returned to the distributor or dealer

of Grundfos' products from which it was purchased

together with proof of purchase and installation date,

failure date, and supporting installation data.

Unless otherwise provided, the distributor or dealer

will contact Grundfos or an authorized service station

for instructions. Any defective product to be returned

to Grundfos or a service station must be sent freight

prepaid; documentation supporting the warranty

claim and/or a Return Material Authorization must be

included if so instructed.

GRUNDFOS WILL NOT BE LIABLE FOR ANY

INCIDENTAL OR CONSEQUENTIAL DAMAGES,

LOSSES, OR EXPENSES ARISING FROM

INSTALLATION, USE, OR ANY OTHER CAUSES.

THERE ARE NO EXPRESS OR IMPLIED

WARRANTIES, INCLUDING MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE,

WHICH EXTEND BEYOND THOSE WARRANTIES

DESCRIBED OR REFERRED TO ABOVE.

Some jurisdictions do not allow the exclusion or

limitation of incidental or consequential damages

and some jurisdictions do not allow limit actions on

how long implied warranties may last. Therefore, the

above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights and you

may also have other rights which vary from

jurisdiction to jurisdiction.

1. Limited warranty 4

2. Symbols used in this document 5

3. Introduction 5

4. Items supplied 5

5. Applications 5

5.1 Pumped liquids 5

6. Identification 6

6.1 Type key 6

7. Operating conditions 7

7.1 Suction lift 7

8. Mechanical installation 8

8.1 Location 8

8.2 Foundation 8

8.3 Space requirement 9

8.4 Pipework 9

8.5 Protective cover 10

9. Electrical connection 11

9.1 Generator or inverter 11

9.2 Wiring diagram 12

9.3 Winding resistance measurement 12

9.4 Winding resistance measurement 13

9.5 Startup 14

10. Functions 15

10.1 Control panel 15

10.2 Pump stop 16

11. Maintenance 17

11.1 Service kits 17

11.2 Shaft seal run-in 17

11.3 Start-up after a long period of inactivity 17

12. Service 17

13. Technical data 18

13.1 Dimensions 18

13.2 Electrical data 18

13.3 Approvals 18

14. Accessories 18

15. Fault finding chart 19

16. MQ frequently asked questions 20

17. Disposal 20

Warning

Prior to installation, read these

installation and operating instructions.

Installation and operation must comply

with local regulations and accepted

codes of good practice.

5

English (US)

2. Symbols used in this document

3. Introduction

The MQ is a low-noise water supply system

consisting of pump, motor, pressure tank and

controller combined into one compact unit.

The system is suitable for both indoor and outdoor

use.

The self-priming pump starts automatically when

water is consumed in the installation and stops when

consumption ceases. The internal, built-in non-return

valve prevents backflow during priming and

operation.

The MQ pump incorporates overtemperature and

dry-running protection as well as a user-friendly

control panel.

The built-in pressure tank reduces the number of

starts and stops in case of leakage in the installation.

4. Items supplied

The MQ packaging contains these items:

• MQ water supply system with built-in non-return

valve

• non-return inlet valve in plastic bag

• installation and operating instructions.

5. Applications

The MQ water supply system is designed for these

typical applications:

• water pressure boosting

(maximum inlet pressure: 40 psi)

• water supply from wells

(maximum suction lift: 25 ft), for example

– in private homes

– on farms

– in market gardens and other large gardens.

The pump is suitable for rain water.

5.1 Pumped liquids

Thin, clean, non-aggressive liquids, not containing

solid particles or fibres.

Warning

If these safety instructions are not

observed, it may result in personal

injury.

Caution

If these safety instructions are not

observed, it may result in malfunction

or damage to the equipment.

Note

Notes or instructions that make the job

easier and ensure safe operation.

6

English (US)

6. Identification

6.1 Type key

Fig. 1 MQ water supply system. Protective cover is required for outdoor use.

Example MQ 3 -35 A -O -A BVBP

Pump type

Rated flow rate [m3/h]

Head [m]

Code for pump version

A: Standard

Code for pipework connection

Code for materials

A: Standard

Code for shaft seal

TM04 3648 4908

Base plate

Drain plug

Suction port

Priming plug

Discharge port Control panel Pressure tank cover

End-cover plug

Protective cover

(accessory)

7

English (US)

7. Operating conditions

7.1 Suction lift

The maximum suction lift of the pump can be

determined from the diagram, page 56.

Example:

If the suction lift is 10 ft, the length of the suction pipe

must not exceed 72 ft.

MQ 3-35 MQ 3-45

Maximum flow rate [gpm] 22

Maximum inlet pressure [psi] 40

Pump discharge range [psi] 15-49 18-63

Maximum combined discharge pressure: Max.

Inlet + pump discharge range [psi] 55-89 58-103

Maximum suction lift [ft]; see page 56 25

Minimum ambient temperature [°F]/[°C] 32/0

Maximum ambient temperature [°F]/[°C] 113/45

Minimum liquid temperature [°F]/[°C] 32/0

Maximum liquid temperature [°F]/[°C] 95/35

Net weight [lbs] 29

Sound pressure level [dB(A)] < 70

Tank volume [oz] 13.5

Air pressure in tank [psi] 22 to 25

Connections 1" NPT

Priming and drain plugs 3/8" GAS

8

English (US)

8. Mechanical installation

8.1 Location

The pump is suitable for indoor and outdoor

installation. It is resistant to sunlight.

8.2 Foundation

Mount the pump on the base plate with horizontal

suction port and vertical discharge port.

The pump must be installed horizontally.

The maximum permissible inclination angle is ± 18 °.

See fig. 2.

Fig. 2 Horizontal installation of MQ

To prevent movement and vibrations, the pump and

base plate can be secured to a solid foundation by

means of the bolt holes in the base plate.

For pipework connection, see section 8.4 Pipework.

The bolt holes are covered by a thin plastic layer that

must be knocked out before use. See fig. 3.

Fig. 3 Knocking out the plastic layer in bolt

hole

Fig. 4 Base plate

Note

For outdoor installation, the pump

must be fitted with a protective cover

(accessory). See section 8.5 Protective

cover and 14. Accessories.

Caution

Should the unlikely event of an internal

leakage occur, pumped liquid will be

drained out from the base and/or end

cover instead of damaging the pump.

Install the pump in such a way that no

undesirable collateral damage can

arise.

TM01 9691 2600

Max. ± 18 °

TM05 5156 3412TM01 9692 2600

11.4 cm

19.0 cm

9

English (US)

8.3 Space requirement

For inspection and service, allow a minimum

clearance of 6" behind the pump.

Fig. 5 Minimum clearance behind the pump

Being self-cooling, the pump requires no space or

ventilation at the sides.

8.4 Pipework

The pump is supplied with 1" NPT screwed

connections. Fit the connections in the suction and

discharge ports. See fig. 6. The pump discharge port

is flexible, ± 5 °, to facilitate the fitting.

Fig. 6 Fitting of screwed connections in suction

and discharge ports

Carefully screw the discharge connection into the

discharge port, using a spanner or similar tool.

Hold the discharge connection, and tighten the pump

discharge union nut with your hand. See fig. 7.

Fig. 7 Correct: Tighten the discharge union nut

with your hand

Fig. 8 Wrong: Do not use a tool to tighten the

discharge union nut

8.4.1 Suction pipes connected to a well

If the pump draws water from a well, we recommend

to fit a foot valve to the end of the suction pipe.

See fig. 9.

Fig. 9 Suction pipes connected to a well

TM04 3746 5008

Note

Ensure that the maximum ambient

temperatures do not exceed the values

stated in section 7. Operating

conditions.

Note

Never use unnecessary force when

connecting the pipes.

TM01 9698 2600

6"

TM04 4271 1009TM 044272 1009TM01 9693 2600

Foot valve

10

English (US)

8.4.2 Suction hose instead of pipe

If a suction hose is used instead of a pipe, the hose

should not exceed the lengths stated in the graph,

page 56. The suction hose must be minimum ∅1".

The hose must be of the non-collapsible type.

8.4.3 Long suction pipes

A separate non-return inlet valve is supplied with the

pump. In case of long suction pipes, we recommend

to fit the non-return inlet valve in the pump suction

port. See section 8.4.4 Fitting of the non-return inlet

valve

The pipes must be adequately supported on either

side of the pump to avoid straining the pump

connections.

8.4.4 Fitting of the non-return inlet valve

The non-return inlet valve reduces the risk of losing

pump priming in negative suction applications and

improves the auto-aspiration capability, for example

in water supply from a cistern.

Install the non-return inlet valve as follows,

see fig. 10:

1. Remove the suction connection of the pump.

2. Fit the non-return inlet valve into the suction port

in the direction shown in fig. 10.

3. Refit the pump connection.

Fig. 10 Fitting of non-return inlet valve

8.5 Protective cover

The protective cover protects the control panel

against the weather. It is available as an accessory.

See section 14. Accessories.

To fit the protective cover, click the cover onto the

top of the control panel so that it engages with the

top cooling ribs.

To remove the cover, pull the two clips outwards, free

of the cooling ribs, and pull the cover upwards.

Fig. 11 Protective cover

Note

Applications with positive inlet

pressure do not require installation of

the non-return inlet valve due to the

fact that the MQ pump incorporates an

internal non-return valve at the

discharge side.

TM04 4121 0809

Note

Failure to use the protective cover in

outdoor installations will invalidate the

warranty.

TM04 3745 5008

11

English (US)

9. Electrical connection

The electrical connections and additional protection

should be carried out by qualified persons in

accordance with local regulations.

The operating voltage and frequency are marked on

the nameplate. Make sure that the motor is suitable

for the electricity supply on which it will be used.

The pump must be connected to the mains via a

sheathed cable with a protective ground lead.

It is possible to replace the mains supply cable.

See fig. 12.

Fig. 12 Electrical connection

Connect the mains supply cable of the pump to the

electricity supply. When the cable is connected, a red

and a green indicator light on the control panel will

be on. See fig. 13.

Fig. 13 When mains supply cable is connected,

these two indicator lights will be on

9.1 Generator or inverter

Warning

Non-submersible pump.

If the power cord is damaged, it must

be replaced by the manufacturer, an

authorized service center or by a

qualified person in order to avoid risks.

Never make any connections in the

pump terminal box unless the

electricity supply has been switched

off for at least 5 minutes.

Risk of electric shock:

This pump is supplied with a grounding

conductor and grounding type

attachment plug. To reduce the risk of

electric shock, install only on circuit

protected by a Ground-Fault-Circuit-

Interrupter (GFCI).

This pump is not intended, nor has it

been investigated for use in swimming

pool or marine areas.

This pump has been evaluated for use

with water only.

Do not start the pump until it has been

filled with water (primed, see fig. 14).

Acceptable for indoor and outdoor use.

Enclosure type 3.

TM01 9694 2600TM01 9695 2600

Note

The MQ can be powered by a generator

or an inverter. However, the pump will

only operate satisfactorily if the

generator or inverter generates a true

sinusoidal wave with the necessary

power and voltage input. The generator

must be sized 10 % above the P1

(input power) of the pump. For P1,

see section 13.1 Dimensions.

12

English (US)

9.2 Wiring diagram

9.2.1 115 V

Fig. 14 Wiring diagram - 115 V

9.3 Winding resistance measurement

The measurement can be done with or without cables connected to the PCB and the capacitor.

TM02 2424 4708

Black (phase)

Red

Black

Orange > Flow sensor

> Pressure switch

Capacitor

Yellow

Electric motor

Yellow/green (ground)

Red (main)

Black

White (neutral) > Cable

BA

Yellow

White C

Motor

[V/Hz] Measuring point Winding Resistance

[Ω ± 10 %]

Ambient temperature

[°F] [°C]

115/60 A-B (black - red) Main 1.4 70 21

A-C (black - white) Aux 5.5

13

English (US)

9.3.1 230 V

Fig. 15 Wiring diagram - 230 V

9.4 Winding resistance measurement

The measurement can be done with or without cables connected to the PCB and the capacitor.

TM02 2424 2409

Black (phase)

Red

Black

Orange > Flow sensor

> Pressure switch

Capacitor

Yellow

Electric motor

Yellow/green (ground)

Blue

White (neutral) > Cable

BA

Yellow

White

Red (main)

Motor

[V/Hz] Measuring point Winding Resistance

[Ω ± 10 %]

Ambient temperature

[°F] [°C]

230/60 A-B (blue - red) Main 5.4 70 21

A-C (blue - white) Aux 5.4

14

English (US)

9.5 Startup

Before start-up, the pump must be filled with 1.2 to

1.5 gallons of water to enable it to self-prime,

see fig. 16. The pump is self-priming with a

maximum suction lift of 25 ft.

Fig. 16 Priming the pump

When started, the pump begins to self-prime.

When it has been primed, the pump will

automatically change over to normal operation.

If the priming has not been completed within

5 minutes, the pump will stop automatically and

attempt to restart after 30 minutes. It is possible to

reset the pump manually, see point 2 in the table of

section 10.1 Control panel.

TM01 9696 2600

Warning

Running the pump at a higher inlet

pressure than recommended (44 psi)

can cause the pump to leak.

Grundfos cannot be held responsible

for any damage to the pump and/or its

surroundings if this warning is not

followed.

15

English (US)

10. Functions

10.1 Control panel

The MQ pump is operated entirely by means of the

control panel. See fig. 1. The control panel offers the

possibility of starting/stopping the pump. The pump

settings and operating condition are indicated by

indicator lights. See fig. 17.

Fig. 17 Control panel

The functions of the control panel are described in the table below:

TM01 9684 2600

Illustration Description

1

Indicator light (red):

When the indicator light is on, the pump is on standby.

2

On/off button:

The pump is started/stopped by means of the on/off button.

The on/off button can also be used for manual resetting in case

of an alarm condition:

• press once for resetting and

• press once more for starting.

3

Indicator light (green):

Indicates that the pump is ready for operation.

When the indicator light is on, the pump will start automatically

when water is consumed. After-run time depends on the

flexibility of the discharge pipe, but will be at least 10 seconds.

4

Pump on (green):

The indicator light is on when the pump is running.

16

English (US)

10.2 Pump stop

The pump incorporates an electronic protective

function that will stop the pump in case of

• dry running

• overtemperature

• overloaded motor

• seized-up motor/pump.

The pump will restart automatically after 30 minutes

(for 24 hours) in case of any type of fault if the auto-

reset function is activated (the green indicator light

on the control panel is on, see point 5 in the table of

section 10.1 Control panel).

5

Auto-reset (green):

As standard, this function is activated on delivery (does not

apply to pump versions for Australia).

When the indicator light is

• on, the Auto-reset function is activated. The pump will

automatically attempt to restart every 30 minutes after an

alarm/fault over a period of 24 hours. After this period, the

pump will remain in the alarm condition.

• off, the Auto-reset function is deactivated. The pump will not

restart after an alarm/fault.

The Auto-reset function can be activated/deactivated by

pressing the on/off button for 5 seconds.

Note: When water is consumed, the pump will start and stop

automatically, whether the Auto-reset light is on or off.

6

Alarm (red):

The indicator light is on when the pump is in alarm condition.

The alarm condition may have been caused by:

• dry running

• overtemperature

• overloaded motor

• seized-up motor/pump.

See section 10.2 Pump stop.

Illustration Description

Note

The pump settings are stored.

After supply failure, the pump will

automatically revert to its previous

operating condition when the

electricity supply is reconnected.

17

English (US)

11. Maintenance

Under normal operating conditions, the pump is

maintenance-free. However, it is recommended to

keep the pump clean.

If there is any risk of frost damage, drain the pump

through the drain hole and slacken the union nut on

the discharge pipe, see fig. 18. The pump must be

filled with liquid before it is started up again.

See fig. 16.

Fig. 18 Draining the pump

11.1 Service kits

Service kits are available for the MQ pump.

The service kits consist of the following replaceable

parts:

• shaft seal

• motor

• electronic units

• hydraulic components.

11.2 Shaft seal run-in

The seal faces are lubricated by the pumped liquid,

meaning that there may be a certain amount of

leakage from the shaft seal.

When the pump is started up for the first time, or

when a new shaft seal is installed, a certain run-in

period is required before the leakage is reduced to

an acceptable level. The time required for this

depends on the operating conditions, i.e. every time

the operating conditions change, a new run-in period

will be started.

Under normal conditions, the leaking liquid will

evaporate, which means that no leakage will be

detected.

11.3 Start-up after a long period of

inactivity

The end cover incorporates a plug which can be

removed by means of a suitable tool. See fig. 19.

It is then possible to free the pump rotor if it has

seized up as a result of inactivity. If it has been

drained, the pump must be filled with liquid before

start-up. See fig. 16.

Fig. 19 Removing the end-cover plug

12. Service

If Grundfos is requested to service the pump,

Grundfos must be contacted with details about the

pumped liquid, etc. before the pump is returned for

service. Otherwise Grundfos can refuse to accept

the pump for service.

Possible costs of returning the pump are paid by the

customer.

However, any application for service (no matter to

whom it may be made) must include details about

the pumped liquid if the pump has been used for

liquids which are injurious to health or toxic.

Warning

Do not remove the pressure tank from

the pump unless it has been vented

through the air escape valve.

Never touch the electronics unless the

pump has been switched off for at least

5 minutes.

TM01 9697 4403

TM04 3633 4608

Note

If a pump has been used for a liquid

that is injurious to health or toxic, the

pump will be classified as

contaminated.

18

English (US)

13. Technical data

13.1 Dimensions

13.2 Electrical data

13.3 Approvals

CSA-approved for USA and Canada

Class 6861 08 - Mechanical devices - NSF/ANSI 61

Section 8 - Certified to NSF/ANSI 61

Class 6853 01 - Low lead content certification

program - Plumbing products

Class 3385 01 - Liquid pumps

Class 3851 81 - Liquid pumps - Certified to US

standards

14. Accessories

TM01 9799 5008

MQ 3-35 MQ 3-45

Enclosure type 3

Enclosure class IP54

Insulation class B

Supply cable 6.56 ft SJTW 18 awg with/without plug

Voltage, power consumption,

P1 [W] 1 x 115-120 V - 10/+ 6 %, 60 Hz 900 W / 8.0 A 1100 W / 10.0 A

1 x 220-240 V - 10/+ 6 %, 60 Hz 850 W / 4.0 A 1050 W / 4.8 A

Model Designation Product number

MQ 3-35 / MQ 3-45 Protective cover 96693071

19

English (US)

15. Fault finding chart

If the pump does not start when the fault has been corrected, contact your pump supplier or Grundfos for

further information.

Fault Cause Remedy

1. The pump does

not start. a) Insufficient water. Check the water supply/suction pipe.

b) Overheating due to excessive liquid

temperature (above +95 °F / +35 °C). Supply cold liquid to the pump.

c) Overheating due to seized-up/

choked-up pump. Contact your pump supplier.

d) Too low or too high supply voltage. Check the supply voltage and correct the

fault, if possible.

e) No electricity supply. Connect the electricity supply.

f) No water consumption. Open a tap. Check that the height

between the top point of the discharge

pipe and the pump does not exceed 50 ft.

g) Shaft is blocked. Rotate the shaft as described in

11.3 Start-up after a long period of

inactivity.

h) Pump is in alarm condition. Reset the pump by means of the on/off

button. See point 2 in the table of

section 10.1 Control panel.

2. The pump does

not stop. a) Existing pipework is leaking or

defective. Repair the pipework.

b) Non-return valve is blocked or

missing. Clean the valve or fit a new non-return

valve.

3. The pump cuts

out during

operation.

a) Dry running. Check the water supply/suction pipe.

b) Overheating due to excessive liquid

temperature (above +95 °F / +35 °C). Supply cold liquid to the pump.

c) Overheating caused by:

– high ambient temperature

(> 113 °F / 45 °C)

– overloaded motor

– seized-up motor/pump.

Contact your pump supplier.

d) Too low supply voltage. Check the supply voltage and correct the

fault, if possible.

4. The pump starts

and stops too

frequently.

a) Leakage in suction pipe or air in

water. Check the water and the supply/suction

pipe.

b) Too low or too high pressure in

pressure tank. Check the pressure in the pressure tank.

See section 7. Operating conditions.

5. The pump gives

electric shocks. a) Defective ground connection. Connect the ground connection to the

pump in accordance with local

regulations.

6. The pump starts

when no water is

consumed.

a) Internal non-return valve is

defective, or the existing pipework

is leaking or defective. Clean the valve or fit a new one.

20

English (US)

16. MQ frequently asked questions

1. What causes the MQ to start?

Answer: The MQ is equipped with both an

internal flow switch and pressure switch. Each of

these can turn the MQ on, depending on water

consumption. The pump will start when:

The flow rate is greater than 0.3 gpm

OR

the pressure is below 29 psi.

2. What causes the MQ to stop?

Answer: Other than the manual on/off button,

only the flow switch is authorized to automatically

stop the MQ during normal operation when flow

drops below 0.3 gpm. The pump will shut off in

12-15 seconds after flow stops.

Additionally, the MQ will be turned off in the event

of a dry-run or overtemperature alarm.

3. What is the maximum height of a tap above

the MQ?

Answer: If a tap or faucet is installed at heights

greater than 50 ft above the MQ, there is the

potential risk that the MQ will never start.

In cases where the MQ starts due to low pressure

(low flow rates), the pressure has to fall below

the pressure switch activation point (28-30 psi

factory setting). To allow for the pressure of 50 ft

of water, tolerances and a safety margin, we

recommend a maximum height of 50 ft between

the MQ and any tap.

4. What is the purpose of the built-in pressure

tank?

Answer: The built-in pressure tank comes from

the factory, pressurized at approximately 23 psi

(with the pump pressure at zero) and holds a

volume of 14 ounces of water. It is designed to

minimize motor startup due to small leaks.

5. How is the dry-run condition determined?

Answer: The dry-run alarm is declared when the

motor is running AND the flow rate is less than

1.6 gpm AND when pressure is less than the

pressure switch setting. When this condition lasts

for 12 seconds, the alarm will be declared after

1 minute, and the motor is stopped. The MQ

attempts to automatically restart every

30 minutes for a maximum of 24 hours. If more

than 24 hours pass without water, the pump must

be restarted manually.

6. What is the maximum inlet pressure allowed

in the MQ?

Answer: For both MQ 3-35 and MQ 3-45, the

maximum internal pressure allowed is 109 psi.

The maximum inlet pressure when added to the

MQ pressure must not exceed 109 psi.

Remember that inlet pressure adds to the MQ

pressure, so with a 40 psi inlet pressure supplied

to the MQ 3-45, internal pressures can reach

approximately 105 psi (65 + 40 psi).

Additionally, if inlet pressures exceed the built-in

pressure switch activation point (28-30 psi

factory setting), the pressure switch will be

unable to activate, and the ability to turn the MQ

on at low flow rates will be lost. In this situation,

only the flow switch will be able to turn the MQ on

at flow rates above its activation point of 0.3 gpm.

7. What is the priming capacity of the MQ?

Answer: Approx. 1.2 gallons.

8. How is overload temperature/overtemperature

of the MQ detected?

Answer: The motor has a thermal switch

incorporated in the motor windings.

The switch will cut out the motor and start again.

See the table below.

9. Where can a pressure gauge be easily

installed to measure the discharge pressure?

Answer: In the discharge piping or in 3/8" GAS

straight thread opening used to add priming

water to the pump.

17. Disposal

This product or parts of it must be disposed of in an

environmentally sound way:

1. Use the public or private waste collection service.

2. If this is not possible, contact the nearest

Grundfos company or service workshop.

Subject to alterations.

Thermal protection

[V][°F][°C]

Cut-out 115 302 150

230 275 135

Cut-in Both 151 65-67

La page charge ...

Grundfos MQ 3-35 Guide d'installation

Ce manuel convient également à

Grundfos MQ 3-35 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents