Extron DTP T DSW 4K 333 Manuel utilisateur
- Catégorie
- Commutateurs vidéo
- Taper
- Manuel utilisateur
Ce manuel convient également à
User Guide
DTP T DSW 4K Series
Video Products
DTP Switchers
68-2761-01 Rev. C
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVISO: Questo simbolo, ,quando viene utilizzato il prodotto, serve
ad avvisare l’utente della presenza di tensioni pericolose non isolate
all’interno del prodotto, che può presentare un rischio di scosse
elettriche.
ATTENTZIONE: Questo simbolo, , quando viene utilizzato il
prodotto, serve ad avvisare l’utente di importanti istruzioni di uso e
manutenzione (assistenza) nella letteratura fornita con l’apparecchiatura.
Per informazioni sulle linee guida di sicurezza, adempimenti normativi,
compatibilità EMI/EMF, accessibilità e argomenti correlati, vedere la sicurezza
di Extron e Regulatory Compliance Guide, parte numero
68-290-01, sul sito Web Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01
。
安全記事 • 繁體中文
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有
重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資
訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。
安全上のご注意
• 日本語
警告: この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 が製品上に表示されている場合は、本機の取扱説明書に
記載されている重要な操作と保守(整備)の指示についてユーザーの注意
を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウェブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.
com)의 Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
ATTENTION: The Twisted Pair Extension technology works with shielded twisted pair
(STP) cables only. To ensure FCC Class A and CE compliance, STP cables and STP
connectors are also required.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and Regulatory
Compliance Guide” on the Extron website.
Copyright
© 2017
-2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks
®
, registered service marks
(SM)
, and trademarks
(TM)
are the property of RGB Systems, Inc. or
Extron Electronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(®)
AVTrac, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Global Configurator,
GlobalScripter, GlobalViewer, Hideaway, Inline, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,
PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink,
V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTPSystems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple Suppression),
DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital Sync
Validation Processing), eLink, EQIP, EverLast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque,
ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, SIS, SimpleInstructionSet, Skew-Free,
SpeedNav, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, ZipCaddy, and ZipClip
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
• Risk of property damage.
• Risque de dommages matériels.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&* X2)* X2#* X2! CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” is the capital
letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at www.extron.com/technology/glossary.aspx.
viExtron DTP T DSW 4K Series • Contents
Contents
Introduction............................................................ 1
DTP T DSW 4K Series Description ..................... 1
Features ............................................................. 1
Application Diagram ........................................... 2
Installation and Features .................................... 3
Mounting the Units ............................................. 3
Tabletop Use .................................................. 3
Mounting Kits ................................................. 3
UL Rack-Mounting Guidelines ........................ 4
Front Panel Features ........................................... 4
Rear Panel Features ........................................... 5
Twisted Pair Recommendations for DTP
Communication ................................................. 8
Supported Cables .......................................... 8
Cable Recommendations ............................... 8
Power Supply Wiring .......................................... 9
SIS Commands ................................................... 11
Introduction to SIS ........................................... 11
Host-to-Switcher
Communications ......................................... 11
Switcher-Initiated Messages ......................... 11
Copyright Information ................................... 11
Symbols Used in this Guide .............................. 12
Symbol Definitions ........................................ 12
Error Messages ............................................ 14
EDID ............................................................. 14
TMDS Output Format ................................... 14
DTP T DSW 4K Series EDID
Memory Locations ........................................... 15
Command and Response Table for SIS
Commands ..................................................... 16
Extron DTP T DSW 4K Series • Introduction 1
Introduction
This guide describes the function, installation, and operation of the DTP T DSW 4K series
of switchers. Unless otherwise stated, the terms “switcher” and “transmitter” are used
interchangeably in this guide to refer to all of the products in the series.
This section provides the following information:
• DTP T DSW 4K Series Description
• Features
• Application Diagram
DTP T DSW 4K Series Description
The DTP T DSW 4K series extends and switches RGB, HDMI, and DisplayPort™ signals up
to 230 feet (70 meters) for the 233 model, and 330 feet (100 meters) for the 333 model over
shielded twisted pair (STP) cables. Both models are fully High-bandwidth Digital Content
Protection (HDCP) compliant on the HDMI and DisplayPort connections.
These switchers support data rates up to 10.2 Gbps (3.4 Gbps per color) with up to 12-bit
deep color and use the EDID Minder feature for EDID management.
The automatic output compatibility correction feature scans each output device to ensure
that the output signal is compatible with the color depth and format requirements of the
device.
Features
• The DTP T DSW 4K 233 and DTP T DSW 4K 333 transmit DisplayPort, HDMI,
or VGA plus control and analog audio up to 230 (70 meters) and 330 feet (100
meters), respectively, over an STP cable — The DTP T DSW 4K series provides
high reliability and maximum performance on an economical and easily installed cable
infrastructure.
• Inputs: One DisplayPort, one HDMI, and one VGA on 15‑pin HD, one 3.5 mm
stereo mini jack for audio — The DTP T DSW 4K 333 allows for switching between
DisplayPort, HDMI, and analog video sources.
• Output: One DTP 230 or 330 (depending on model) twisted pair output on RJ‑45
• Auto‑switching between inputs — Auto-switching allows for simple, unmanaged
installation in locations such as in a lectern or under a conference table. When multiple
inputs are active, the switching priority is configurable.
• Supports computer and video resolutions up to 4K, including 1080p/60 Deep
Color
• Analog stereo audio embedding — Analog stereo audio signals can be selectively
embedded onto the digital video output signal and transported over DTP. The
DisplayPort and HDMI inputs can be set to pass the embedded digital audio, embed
the analog audio, or to automatically (HDMI and DP inputs only) embed the analog
audio when no digital audio is detected.
Extron DTP T DSW 4K Series • Introduction 2
• DTP output is compatible with HDBaseT‑enabled devices — The DTP output
can be configured to send video and embedded audio, plus bidirectional RS-232 and
unidirectional IR signals to an HDBaseT-enabled display.
• Accepts additional analog stereo audio signals — The DTP T DSW 4K series
accepts stereo analog audio signals for simultaneous transmission over the same
shielded twisted pair cable.
• Bidirectional RS‑232 and IR pass‑through for AV device control — Bidirectional
RS-232 control and IR signals can be transmitted alongside the video signal, allowing
remote AV devices to be controlled without the need for additional cabling.
• HDCP compliant — Ensures display of content-protected media and interoperability
with other HDCP-compliant devices.
• Supports DisplayPort SST — Single Stream Transport data rates up to 10.8 Gbps
• Supported HDMI specification features include data rates up to 10.2 Gbps,
Deep Color up to 12‑bit, 3D, and HD lossless audio formats
• Digital conversion of analog input signals — Analog video signals up to 1920x1200
are digitized, ensuring that a reliable, high quality digital video signal is sent to the output
destination.
• RS‑232 control port — Enables the use of serial commands for integration into
a control system. Extron products use the SIS - Simple Instruction Set command
protocol, a set of basic ASCII commands that allow for quick and easy programming.
• Contact closure remote control with tally output — Allows for remote selection of
an input channel, while a tally output provides +5 VDC to light an LED to indicate the
currently selected input.
• Compatible with all DTP 230 and 330 Series receivers and DTP 230‑ and
330‑enabled products — Enables mixing and matching with desktop and wallplate
receivers, as well as other DTP 230- and 330-enabled products to meet application
requirements.
Application Diagram
The diagram below shows a typical application for the DTP T DSW 4K 333.
Figure 1. DTP T DSW 4K 333 Application Diagram
100-240V ~ -- A MAX
1
2
CONFIGURABLE
HDMI
HDMI
5
6
7
8
C
RS-232 IR
RS-232 IR
Tx Rx TxRxG
Tx Rx TxRxG
Tx Rx TxRxG
HDMI
A
B
3
4
INPUTS
OUTPUTS
Tx Rx
RS-232
G
LAN
2x25W(8
RESET
AUDIO INPUTS
OUTPUTS
REMOTE
LL1R R
L2
R
L
3
CLASS 2 WIRING
L4
R
L5R
+48V
+48V
12
LR
VARIABLE
IN1608 SA
2
MIC/LINE
L6
R
SIG LINK
DTP IN
SIG LINK
DTP IN
SIG LINK
DTP OUT
50/60 Hz
RS-232 IR
OVER DTP
OVER DTP
OVER DTP
AMPLIFIED OUTPUT
SCALING PRESENTATION SWITCHER
INPUTS
1
HDCP
SIGNAL
OUTPUTS
ENTER
MENU
Extron
2 3 4 5 6 7 8 A B C
INPUTS
1 2 3 4 5 6 7 8
CONFIG
POWER
12V
2
--A MAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, YUVHDMIDP
SIG LINK
OUT
AUDIO
CONTACT IN RS-232TALLY OUT
3
123G 123+V
INPUTS
OVER TP REMOTE
DTP
HDBT
T
x
R
x
RS
-23
2
G
LAN
2x25W
(
8
R
E
S
E
T
REM
O
T
E
L
C
LA
SS
2 WIRIN
G
A
MPLIFIED OUTPUT
SC
ALIN
G
PRE
S
ENTATI
O
N
S
WIT
C
HE
R
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
12345678
100
LINK
ACT
COM
IR/S
TX
RX
TX
RX
RTS
CTS
R
5
1
6
2
7
3
8
4
RELAY
FLEX
I/O
5
1
6
2
3
1
4
2
eBUS
ACT LIMIT
OVER
SWITCHED
12VDC
3
1
4
OVER
2
LIMIT
IR
7
3
8
4
IPCP 505
TLP 1000TV
IPCP 505
IN1608
DTP HDMI 330 Rx
Projector
Extron
DTP T DSW 4K 333
Transmitter
Ethernet
HDMI
PC
Blu-Ray
RGB
Laptop
XTP DTP 24 Cable
330'
HDMI
DisplayPort
Extron DTP T DSW 4K Series • Installation and Operation 3
Installation and
Features
This section of the guide describes the following topics concerned with the installation,
setup, and operation of the DTP T DSW 4K series.
• Mounting the Units
• Front Panel Features
• Rear Panel Features
• Power Supply Wiring
• Twisted Pair Recommendations for DTP Communication
Mounting the Units
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé
uniquement.
The DTP T DSW 4K series can be placed on a table, mounted in a rack, or mounted under
a desk or table.
Tabletop Use
Affix the included rubber feet to the bottom of the unit and place it in any convenient
location.
Mounting Kits
Mount the unit using any optional compatible mounting kit listed on the Extron website
(www.extron.com), in accordance with the directions included with the kit. For rack
mounting, see UL Rack‑Mounting Guidelines below.
UL Rack-Mounting Guidelines
The following Underwriters Laboratories (UL) requirements pertain to the installation of the
unit into a rack.
• Elevated operating ambient temperature — If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater
than room ambient. Therefore, consider installing the equipment in an environment
compatible with the maximum ambient temperature (TMA = +122 °F, +50 °C) specified
by Extron.
• Reduced air flow — Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
Extron DTP T DSW 4K Series • Installation and Operation 4
• Mechanical loading — Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
• Circuit overloading — Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might have
on overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
• Reliable Earthing — Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply a connection other than a
direct connection to a branch circuit, such as by using a power strip.
Front Panel Features
AUTO
SWITCH
DTP T DSW 4K 333
3
CONFIG
231
STAT US
SIGNAL
HDCP
AUTO
2
NORMAL
1
MODE
POWER
12V
2
1.4 A MAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, YUV HDMI DP
SIG LINK
OUT
AUDIO
CONTACT IN RS-232TALLY OUT
3
123G 123+V
INPUTS
OVER TP REMOTE
DTP
HDBT
B
C
C
A
G
B
C
C
C
A
D
E
F
E
D
C
Figure 2. DTP T DSW 4K Series Front Panel
A
Auto Switch LED — Lights green when auto switch mode is enabled.
• When enabled, auto switch mode automatically selects the highest numbered input
with an active signal (based on sync/clock).
• To enable auto-switch mode via the front panel, press and hold the MODE (Input 1)
button, then press and release the AUTO (Input 3) button.
• Once enabled, to return to normal (manual) switch mode, press and hold the MODE
(Input 1) button, then press and release the NORMAL (Input 2) button. The Auto
Switch LED turns off.
B
USB Config port — Used for firmware updates, SIS configuration, and software
control.
C
Input selection buttons — Selects the active input and used to change switching
modes. Each button has an associated LED that lights green to indicate input selection
status.
• Executive Mode — Executive Mode locks out the front panel buttons, preventing
input selections via the front panel.
NOTE: Control via RS-232 and USB is still possible when Executive Mode is
enabled.
To enable or disable Executive Mode via the front panel, press and hold all three
input selection buttons for 5 seconds. All front panel LEDs flash three times
simultaneously to indicate the enabling or disabling of Executive Mode.
NOTE: If input selection is attempted while Executive Mode is enabled, all front
panel LEDs flash once to indicate they are locked out.
D
Input signal LEDs — Light green when a signal is detected on the associated input.
E
Input HDCP LEDs — Light green when HDCP presence is detected on the associated
input.
Extron DTP T DSW 4K Series • Installation and Operation 5
Rear Panel Features
AUTO
SWITCH
DTP T DSW 4K 333
3
CONFIG
231
STAT US
SIGNAL
HDCP
AUTO
2
NORMAL
1
MODE
POWER
12V
2
1.4 A MAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, YUV HDMI DP
SIG LINK
OUT
AUDIO
CONTACT IN RS-232TALLY OUT
3
123G 123+V
INPUTS
OVER TP REMOTE
DTP
HDBT
B
C
C
A
G
B
C
C
C
A
D
E
F
E
D
C
Figure 3. DTP T DSW 4K Series Rear Panel
A
DC power input connector — Wire and connect the included external 12 VDC 2 A
power supply into this 2-pole connector. The DTP T DSW 4K series can provide remote
power to a compatible receiver (see Power Supply Wiring on page 9).
ATTENTION:
• Remote power is intended for indoors use only. No part of a network that uses
remote power can be routed outdoors.
• L’alimentation à distance est exclusivement réservée à un usage en intérieur.
Un réseau utilisant une alimentation à distance ne peut pas être routé en
extérieur.
• Do NOT connect an HDBaseT unit if using DTP transmission. The power
carried over DTP may damage the unit.
• Ne PAS connecter une unité HDBaseT si vous utilisez la transmission DTP.
L’alimentation transmise sur DTP peut endommager l’unité.
B
Audio input — Wire and connect an audio source to this 3.5 mm
tip-ring-sleeve (TRS) connector for analog audio input. Wire the
connector as shown to the right.
C
Input Connectors
• RGB, YUV — Connect a video source to this 15-pin HD connector.
• HDMI — Connect a video source to this HDMI connector.
• DisplayPort (DP) — Connect a video source to this DisplayPort connector.
A
DC power input connector
E
DTP/HDBaseT configuration switch
B
Audio input connector
F
Over TP RS‑232/IR connector
C
Input connectors
G
Remote connectors
D
DTP/HDBaseT output
Sleeve ( )
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
Extron DTP T DSW 4K Series • Installation and Operation 6
D
DTP/HDBaseT output — Use an STP cable to connect this output to the input of a
compatible receiver (see Twisted Pair Recommendations for DTP Communication
on page 8 for more information).
ATTENTION:
• Do not connect these ports to a computer data network or a
telecommunications network.
• Veuillez ne pas connecter ces ports à un réseau de données informatiques ou
à un réseau de télécommunications.
• Do NOT connect an HDBaseT unit if using DTP transmission. The power
carried over DTP may damage the unit.
• Ne PAS connecter une unité HDBaseT si vous utilisez la transmission DTP.
L’alimentation transmise sur DTP peut endommager l’unité.
• Remote power is intended for indoors use only. No part of a network that uses
remote power can be routed outdoors.
• L’alimentation à distance est exclusivement réservée à un usage en intérieur.
Un réseau utilisant une alimentation à distance ne peut pas être routé en
extérieur.
E
DTP/HDBaseT configuration switch — Set this 2-position, recessed switch to
configure the output between DTP and HDBaseT modes. When configured for DTP, use
a DTP-compatible receiver. When configured for HDBaseT, use an HDBaseT-compatible
receiver.
NOTES:
• When the switch is set to DTP mode and the unit is locally powered, the
DTP T DSW 4K units can provide remote power to a compatible receiver. The
units cannot receive remote power in either mode.
• When the switch is set to HDBaseT mode, remote power is disabled and
power supplies are required for both switcher and receiver. Analog audio is
enabled, but incompatible with third-party HDBaseT devices.
F
Over TP port
• RS‑232 Over TP port — To pass bidirectional serial control between
DTP-compatible or HDBaseT-compatible devices, connect a control
device to the 5-pole captive screw connector. This port includes only the
3 poles labeled “RS-232” (see image below for wiring instructions).
• IR Over TP port — To transmit and receive IR signals, connect a
control device to the 5-pole captive screw connector. This port includes
only the 2 poles labeled “IR” and shares the ground pole with the RS-
232 port (see figure 4 for wiring instructions).
Tx/Rx
Pins
Rx GTx
RS‑232 IR
RxTx
TxRx
RxTx
Gnd
Gnd
IR Device
RS-232 Device
Figure 4. Over TP Port Wiring
NOTE: RS-232 and IR data can be transmitted simultaneously.
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
RS-232
Extron DTP T DSW 4K Series • Installation and Operation 7
G
Remote connectors
• Contact input — Connect a locally-constructed contact closure device to the
4-pole captive screw connector. The three left ports (1, 2, and 3) are used to select
inputs 1 through 3 when momentarily shorted to the fourth port (G). The closure
accepts a momentary or latching contact.
• Tally output — If desired, to remotely identify the currently selected input, plug a
locally-constructed device into the 4-pole captive screw connector. Connect the
power wire for the device into the +V pin and connect the ground wire for the each
indicator into the corresponding tally out pin, 1, 2, or 3. When an input is selected,
by either contact closure or front panel selection, the corresponding tally out pin
shorts to ground, closing the circuit and lighting the connected indicator (LED).
TIP: The Contact and Tally connectors can be used with Extron “Show Me”
cables. For each “Show Me” cable, connect the red pigtail to the associated
pin of the Contact Closure input connector and the black pigtail to the
associated pin on the Tally Out connector (see figure 5). For more information
and installation details for the Extron “Show Me” cable, see the “Show Me”
Cable Series Setup Guide at www.extron.com.
• RS‑232 — Connect a 3.5 mm, 3-pole captive screw connector for RS-232 control
of the unit (see figure 5 for wiring instructions).
Figure 5. RS‑232, Contact, and Tally Connector Wiring
CONTACT IN
+V321
G321
TALLY OUT
REMOTE
Red
Black
“Show Me” Cable
Tx Rx G
RS‑232
Ground
Transmit pin on connected uni
t
Receive pin on connected unit
Extron DTP T DSW 4K Series • Installation and Operation 8
Twisted Pair Recommendations for DTP Communication
Use the following pin configurations for shielded twisted pair cables.
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA
T568B
TP Wires
12345678
Pins:
Figure 6. TP Connector Wiring
Supported Cables
The switchers are compatible with shielded twisted pair cable (F/UTP, SF/UTP, and
S/FTP).
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable to link the device with DTP transmitters or receivers.
• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF-4
d’Extron ou le câble STP201 pour relier le appareil avec les émetteurs ou les
récepteurs DTP.
Cable Recommendations
Extron recommends using the following practices to achieve full transmission distances and
reduce transmission errors.
• Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best
performance:
• XTP DTP 24/1000 Non-Plenum 1000’ (305 m) spool 22-236-03
• XTP DTP 24P/1000 Plenum 1000’ (305 m) spool 22-235-03
• XTP DTP 24 Plug Package of 10 101-005-02
• If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid
conductor, STP cable with a minimum bandwidth of 400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (see figure 6).
• Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, and couplers. If these pass-through points are required, use
shielded couplers and punch down connectors.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the
following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 meters, where cables are straightened,
aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
Extron DTP T DSW 4K Series • Installation and Operation 9
Power Supply Wiring
NOTES:
• In point-to-point applications, only one power supply is required; a single power
supply connected to the switcher can power both the switcher and a compatible
receiver.
• The DTP T DSW 4K series can only transmit remote power. It cannot receive
remote power from a locally powered receiver.
• Remote power is only available when the unit is set to DTP mode. When the unit is
set to HDBaseT mode, remote power and analog audio are disabled.
• A power supply is included with each individually-packaged switcher.
• Do not tin the power supply leads before installing them in the direct insertion
connector. Tinned wires are not as secure in the connectors and could be pulled
out.
Figure 7 shows how to wire the connector.
Power
Receptacle
DC Power Cord
Captive Screw
Connector
DTP T DSW 4K
Switcher
DC Power
Outputs
DO NOT USE
AC Power Cord
Tie
Wrap
Captive Scr
ew
Connector
Power Supply
Output Cord
PS 1220
Power Supply
POWER
12V
1.4A MAX
Figure 7. Power Connector Wiring
CAUTION: The wires must be kept separate while the power supply is plugged in.
Remove power before wiring.
ATTENTION : Les deux cordons d’alimentation doivent être tenus à l’écart l’un de
l’autre quand l’alimentation est branchée. Couper l’alimentation avant de faire
l’installation électrique.
Extron DTP T DSW 4K Series • Installation and Operation 10
ATTENTION:
• Always use a power supply supplied and or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit
final.
• If not provided with a power supply, this product is intended to be supplied by a
power source marked “Class 2” or “LPS” and rated at 12 VDC and a minimum of
2.0 A.
• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit
être alimenté par une source d’alimentation de classe 2 ou LPS et paramétré à 12 V
et 2.0 A minimum.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to
building structure or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui s’applique au
National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical Code,
partie1, section16. La source d’alimentation ne devra pas être fixée de façon
permanente à une structure de bâtiment ou à une structure similaire.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage
the power supply and the unit. The ridges on the side of the cord (see figure 7 on
previous page) identify the power cord negative lead.
• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte
pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du
cordon permettent de repérer le pôle négatif du cordon d’alimentation.
• To verify the polarity before connection, plug in the power supply with no load and
check the output with a voltmeter.
• Pour vérifier la polarité avant la connexion, brancher l’alimentation hors charge et
mesurer sa sortie avec un voltmètre.
• The length of the exposed (stripped) copper wires is important.
The ideal length is 3/16 inch (5 mm). Longer bare wires can short together.
Shorter wires are not as secure in the connectors and could be pulled out.
• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus
longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils
sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis
captives.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales.
Extron DTP T DSW 4K Series • SIS Commands 11
SIS Commands
This section provides information about the SIS commands that are used to configure the
DTP T DSW4K series. The following topics are discussed:
• Introduction to SIS
• Symbols Used in this Guide
• DTP T DSW 4K EDID Memory Locations
• Command and Response Table for SIS Commands
Introduction to SIS
The switcher can be set up and controlled remotely via Extron SIS commands that are
issued from a host computer running the Extron DataViewer utility or other control system.
The host device can be connected to the USB mini-B config port on the front panel or the
RS-232 port on the rear panel.
NOTE: The wiring in the RS-232 cables crosses over so that the unit transmit (Tx) wire
connects with the control device receive (Rx) and vice versa.
Host-to-Switcher Communications
SIS commands consist of strings (one or more characters per command field). No special
characters are required to begin or end a command sequence. Unless otherwise stated,
upper and lower case characters can be used interchangeably. Most responses from the
switcher end with a carriage return and a line feed (CR/LF = ]), which signals the end
of the response character string. When the device determines that a command is valid, it
executes the command and sends a response to the host device.
Switcher-Initiated Messages
When a local event such as a change in signal status takes place, the switcher responds by
sending a message to the host, indicating the status change. No response is required from
the host.
Copyright Information
The copyright message is displayed upon connecting to a switcher via USB or RS-232.
] © Copyright 20yy, Extron Electronics, DTP T DSW 4K 233/333,
Vx.xx,60-xxxx-01]
20yy is the year the currently installed firmware was released, Vx.xx is the firmware
version number, and 60-xxxx-01 is the catalog part number.
Extron DTP T DSW 4K Series • SIS Commands
12
Symbols Used in this Guide
When programming in the field, certain characters are most conveniently represented by
their hexadecimal rather than their ASCII values. The table below shows the hexadecimal
equivalent of each ASCII character:
ASCII to HEX Conversion Table
Space
.
Symbol Definitions
•
= Space
]
= Carriage return with line feed
| or }
= Carriage return with no line feed
E or
W
= Escape
X!
= Input selection
0 = deselect input (break tie)
1 = RGB input
2 = HDMI input
3 = DisplayPort input
X@
= Status
0 = disabled/off/undetected
1 = enabled/on/detected
X#
= Auto switch mode
0 = disabled (default)
1 = enabled (highest active input has priority)
2 = enabled (lowest active input has priority)
X$
= EDID memory location 1-33
See the DTP T DSW 4K EDID Memory
Locations table on page 15.
X%
= Input HDCP status
0 = no source detected
1 = source with HDCP detected
2 = source without HDCP detected
X^
= Output HDCP status
0 = no sink detected
1 = sink with HDCP detected
2 = sink without HDCP detected
X&
= Unit name: Up to 24
alphanumeric characters
(including hyphen [-])
No spaces allowed
No distinction between upper and lower case
letters
First character must be a letter
Last character cannot be a hyphen (-)
Default is model name
X*
= 128 or 256 byte EDID raw HEX
X(
= Video color bit depth
0 = auto, based on EDID of sink (default)
1 = force 8-bit
Extron DTP T DSW 4K Series • SIS Commands
13
X1)
= TMDS output format
0 = Auto (default)
1 = DVI RGB 444
2 = HDMI RGB “Full”
3 = HDMI RGB “Limited”
4 = HDMI YUV 444 “Full”
5 = HDMI YUV 444 “Limited”
6 = HDMI YUV 422 “Full”
7 = HDMI YUV 422 “Limited”
X1!
= Native resolution and refresh rate
from selected EDID
Example:
1920x1200 @ 60Hz
X1@
= Pixel phase
0 to 63 (32 is default)
X1#
= Total pixels
±255 of the default value (depends on input rate)
X1$
= Horizontal/Vertical start
0 to 255 (128 is default)
X1&
= Verbose mode
0 = clear/none
1 = verbose mode (default)
2 = tagged responses for queries
3 = verbose mode and tagged responses for
queries
X1*
= Tally pin mode on channel mute
0 = always on (default)
1 = off when muted
2 = blink when muted
X1(
= Embedded audio format HDMI and DisplayPort:
0 = auto (default)
1 = force existing digital/embedded audio
2 = force embedded analog audio
VGA:
0 = disable embedded DVI format audio
(default)
1 = enable embedded audio (HDMI format)
X2)
= DTP/HDBaseT switch position
0 = DTP mode (default)
1 = HDBaseT mode
X2!
= HDCP output mode
0 = Encrypt as required by input
(Continuous trials for HDMI sinks, attempt for
10 seconds on DVI sinks,then fail)
1 = Always encrypt
(Continuous trials for HDMI sinks, attempt for
10 seconds on DVI sinks,then fail)
2 = Encrypt as required by input
(Continuous trials for HDMI sinks and DVI sinks)
3 = Always encrypt
(Continuous trials for HDMI sinks and DVI sinks)
Extron DTP T DSW 4K Series • SIS Commands
14
Error Messages
E01 — Invalid input channel number (too large)
E06 — Invalid channel change (unit is in auto switch mode)
E10 — Invalid command
E13 — Invalid parameter
E14 — Not valid for this configuration
E17 — Invalid command for signal type
EDID
User assigned mode
In user assigned mode, the user can select from 29 factory loaded EDID files, each
categorized by rate type (IT or CE), video format (DVI or HDMI), audio type (2-Ch), and
native resolution. The unit retains this setting after a power cycle.
Additionally, three user-loaded slots are available to save the EDID of any connected display.
EDID saved to these slots are retained after a power cycle. Upon a factory reset, these EDID
revert to the factory default (720p @ 60 Hz, 2-Ch audio).
A table showing the factory loaded EDID options is shown on the following page. The EDID
memory location is labelled
X$
for consistency with the value in the SIS commands.
TMDS Output Format
The TMDS output format has three components:
• Video format (HDMI or DVI)
• Colorspace (RGB 4:4:4, YUV 4:2:2, or YUV 4:4:4)
• Quantization range (full [0-255] or limited [16-235])
By default, the output format is configured for AUTO, which automatically forces RGB 4:4:4
Full, with the video format being dependent on the source signal and the sink capabilities.
NOTE: When the source signal is detected as 4K/UHD @ 60 Hz with YUV 4:2:0 (based
on AVI infoframe data), it must pass unaltered, overriding the TMDS output format
setting. If the TMDS output format is changed while this signal type is passing, the
setting is applied, but with no observable change. The TMDS output format resumes
as configured when the source signal changes to a signal other than
4K/UHD @ 60 Hz with YUV 4:2:0.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Extron DTP T DSW 4K 333 Manuel utilisateur
- Catégorie
- Commutateurs vidéo
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Extron DTP T DSW 4K 333 User manual
Documents connexes
-
Extron DTP T USW 333 Manuel utilisateur
-
-
-
Extron DTP T DP 4K 330 Manuel utilisateur
-
-
-
Extron DTP T FB 332 Manuel utilisateur
-
-
Extron DTP T SW4 HD 4K Manuel utilisateur
-
Extron XTP T USW 103 4K Manuel utilisateur
Autres documents
-
BluStream HMXL44ARC-KIT Guide de référence
-
Lindy 38281 Manuel utilisateur
-
-
-
NEC NP01SW3 Le manuel du propriétaire
-
C2G 30020 Le manuel du propriétaire
-
StarTech.com MDP2HDVGAW Manuel utilisateur
-
StarTech.com DP2HDVGA Guide d'installation