Extron DTP T FB 332 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

User Guide
DTP T FB 332
DTP T FB 232
DTP Systems
Two-Input Universal Floor Box
Twisted Pair Transmitters
68-2682-01 Rev. D
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 简体中文
警告 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压,
险。
注意 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站 , www.extron.com,参见
Extron 安全规范指南,产品编号 68-290-01
安全記事 • 繁體中文
警告: 若產品上使用此號,是為了提醒使用者產品機殼內存
可能會導致觸電之風險的未絕緣危險電
注意 產品使用此符號,是為提醒使用備隨附的用戶手冊中有
重要的操作和維(維修説明
有關安全性指導方法規遵EMI/EMF 相容取範圍和相關主題的詳細
訊,請瀏覽 Extron 網站www.extron.com然後參閱《Extron 安全性與法規
守手準則編號 68-290-01
安全上の注意
日本語
警告: この 製品上に表示されている場合は、筐体内に絶縁され
いない高電圧が流れ、感電の危険があるこていま
意:この が製品上に表されている場合は、の取扱説書に
されている重作と保()のについてユーザー
を喚起するものです
安全上の注意、法規厳守、EMI/EMF適合性、その他の関連項目
スト イト www.extron.com Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ださい。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
Copyright
© 2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks(
®
), registered service marks(
SM
), and trademarks(
TM
) are the property of RGBSystems, Inc. or
ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator,
GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,
PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork,
TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTPSystems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple
Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator,
DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP,
MicroDigital, Opti-Torque, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, Show Me,
SIS, SimpleInstructionSet, Skew-Free, SpeedNav, StudioStation, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, and
ZipCaddy
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
ATTENTION: The Twisted Pair Extension technology works with unshielded twisted
pair (UTP) or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE
compliance, STP cables and STP Connectors are required.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and Regulatory
Compliance Guide on the Extron website.
NOTES:
This unit was tested with shielded I/O cables on the peripheral devices. Shielded
cables must be used to ensur
e compliance with FCC emissions limits.
For mor
e information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide on the Extron website.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
Risk of property damage.
Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,0p1 scene 1,1 ^B 51 ^W^C.0
[01]
R
0004
00300
00400
00800
00600
[02]
35
[17] [03]
E X! *X1&* X1(* X2#* X2) CE}
NOTE: For commands and examples of computer or device responses used in this
guide, the character “0” is used for the number zero and “O” is the capital letter
“o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the
File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.
viiDTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Contents
Introduction ...................................................1
About this Guide ................................................. 1
About the DTP T FB 332 and DTP T FB 232
Switching Transmitters ....................................... 1
Features ............................................................. 3
Installation ..................................................... 4
Installation Overview ........................................... 4
Adapter Plates .................................................... 5
Side Panel Features ............................................ 7
Connectors and Switch Below the Adapter
Plates ............................................................ 7
Connectors Above the Adapter Plates ............ 8
Top Panel Features ............................................. 9
Mounting .......................................................... 10
Ackermann GB3 (OBO Bettermann)
Floor Box ..................................................... 10
MK Electric CableLink Plus - Single Pan
Floor Box ..................................................... 11
MK Electric CableLink Plus - Modular
Floor Box ..................................................... 11
Electraplan or PUK Floor Box ....................... 12
Connection and Wiring Details ...................... 12
Operation ......................................................... 17
Indications .................................................... 17
Switch Modes............................................... 17
EDID ............................................................. 17
Reset Mode .................................................. 17
Troubleshooting — If No Image Appears ........... 18
Remote Control ...........................................19
Simple Instruction Set Control .......................... 19
Host-to-Switcher Communications ............... 19
Switcher-Initiated Messages ......................... 19
Error Responses ........................................... 20
Timeout ........................................................ 20
Using the Command and Response Table .... 20
Product Configuration Software ........................ 26
Installing the Software ................................... 26
Starting the Program .................................... 28
Updating the Firmware ................................. 30
Contents
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Contents viii
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Introduction 1
Introduction
About this Guide
About the DTP T FB 332 and DTP T FB 232 Switching Transmitters
Features
About this Guide
This guide describes the following two floor box-mounted switching transmitter models:
DTP T FB 332
DTP T FB 232
NOTE: In this guide:
The units ar
e commonly referred to as “switchers” or “switching transmitters.”
Unless specifically identified by the model name, the discussions in the manual
apply to either model.
The switcher outputs a signal to a compatible DTP r
eceiver. This guide describes how to
install, operate, and configure the switcher.
About the DTP T FB 332 and DTP T FB 232 Switching Transmitters
The DTP T FB 332 and DTP T FB 232 are 2-input VGA and HDMI switchers with DTP
transmitter outputs (see figure 1, on the next page). The switchers are HDCP compliant,
and support 1080p @ 60 Hz Deep Color and 1920x1200 signals.
Each switcher selects between one analog VGA and one HDMI input, including embedded
audio (or DVI video with the appropriate adapter). The switcher converts the selected input,
an optional analog audio input, and bidirectional RS-232 and infrared (IR) control signals to
a proprietary digital signal. The switcher and a compatible DTP receiver extend the usable
distance of video, audio, and control signals over a single Extron XTP DTP 24 shielded
twisted pair (STP) cable (recommended) or Category (CAT) 5e, CAT 6, or CAT 6a STP cable.
The DTP T FB 332 is compatible with a DTP HDMI 330 Rx or DTP DVI 330 Rx receiver, with
a range of up 330 feet (100 meters).
The DTP T FB 232 is compatible with a DTP HDMI 230 Rx or DTP DVI 230 Rx receiver, with
a range of up 230 feet (70 meters).
The switchers fit into floor boxes from OBO Bettermann, MK by Honeywell, Electraplan, and
PUK.
The included external 12 VDC power supply accepts 100 to 240 VAC, 50-60 Hz. A single
power supply connected to either the transmitter or the compatible receiver can power both
units through the STP cable.
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Introduction 2
POWER
12V
2
--A MAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, Y, R-Y, B-Y HDMI HDMI
SIG LINK
DTP OUT
AUDIO
CONTACTRS-232TALLY
3
123G 123+V
RESET
INPUTS
OVER DTPREMOTE
50-60 Hz
100-240V ~
2.0 A MAX
1
L
R
SIG LINK
OUT
SIG LINK
OUT
1
3
4
4
XTP
RS-232 IR
Tx Rx
RTSCTS
GTxRxG Tx Rx G
RS-232 IR
Tx Rx Tx RxG
Tx Rx G
Tx Rx Tx Rx
XTP
RESET
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
LAN 2
LAN 1
LAN 3
HDBT
G
DTP
HDBT
2
1234
5
7
8
6
DTP CROSSPOINT 84
4
CLASS 2 WIRING
8/
R
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
REMOTE
SIG LINK
IN
SIG LINK
IN
AUDIO INPUTS
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
S
DMP EXPANSION
SGG
1
1
2
2
C34C
INPUTS
-S G+S+V
PWR OUT = 6W
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
IR/SERIALeBUSRELAYS
DTP HDMI 330 Rx
OVER DTP
RS-232
IR
Tx Rx Tx RxG
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
Extron
DTP T FB 332
(shown in OBO Bettermann
GESR7 oorbox assembly)
Extron Extron
OUTPUTS
AUDIO
Tx Rx GTxRx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx GTxRx
RS-232 IR
OVER DTP
Monday, December 16, 2013 7:04 AM
Menu DeleteKey
2
ABC
3
DEF
6
MNO
5
JKL
4
GHI
9
WXYZ
8
TUV
0
7
PQRS
1
800.633.9876
End
Call
Call
Enter
Full
Screen
CameraDisplay Presets
Privacy
Near
End
Zoom
In
Zoom
Out
Far
End
Contacts
Name +-
Sources
Andrew
Video Window
Beth
Charlie
David
Ervin
Frank
Greg
Harold
Kevin
Mike
Andrew
(800) 633 - 9876
1 2 3
DTP T FB 232
VGA IN
HDMI IN
HDMI
VGA
HDCP
AUTO
CLIP
AUDIO IN
OTE
32
T
CONFIG
RESET
Tx
Rx
G
Tx
Rx
OVER TP
RS-232
IR
XT
Display
CATx Cable
up to 330'
(100 m)
CATx Cable
up to 330'
(100 m)
CATx Cable
up to 230'
(70 m)
CATx Cable
up to 330'
(100 m)
RS-232HDMI
RS-232 HDMI
Extron
DTP HDMI
230 D Rx
Receiver
AudioAudio
Extron
DTP T USW 333
DTP Transmitter
Inputs
Outputs
Microphones
Extron
SM 26
Surface Mount
Speakers
Extron
DTP CrossPoint 84 IPCP SA
Scaling Presentation Matrix
Ethernet
Wireless
Relay
Ethernet
Extron
TLP Pro 1220
TG
12" Tabletop
TouchLink Pro
Touchpanel
TouchLink
for iPad
TCP/IP
Network
Extron
DTP HDMI 330 Rx
Receiver
Projector
Screen Control
Fits GB2 and GB3
mounting slots
Figure 1. Typical Transmitter and Receiver Application
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Introduction 3
Features
Transmits HDMI or analog video, control, and analog audio up to 330 feet
(100 meters) (DTP T FB 332) or 230 feet (70 meters) (DTP T FB 232) over a
single STP cable — The units provide high reliability and maximum performance on an
economical and easily installed cable infrastructure.
HDBaseT compatible — The DTP output can be configured to send video and embedded
audio, plus bidirectional RS-232 and IR signals to an HDBaseT-enabled display.
Supports computer video to 1920x1200, including HDTV 1080p/60 Deep Color and 2K
Analog stereo audio embedding — Analog stereo audio signals can be selectively
embedded onto the digital video output signal and transported over DTP. The HDMI inputs
can be set to pass the embedded digital audio, embed the analog audio, or to automatically
embed the analog audio when no digital audio is detected.
Accepts additional analog stereo audio signals — The DTP transmitters support
a direct pass through connection for stereo analog audio signals for simultaneous
transmission over the same single twisted pair cable. Analog audio is embedded onto the
digital video signal. A DTP 330 or DTP 230 receiver can output balanced and unbalanced
audio, allowing streamlined integration within an AV system.
Bidirectional RS-232 and IR insertion for AV device control — Control and IR signals
can be transmitted alongside the video signal over DTP connections, allowing the remote
device to be controlled without the need for additional cabling. Bidirectional control insertion
eliminates the need for control system wiring to remote devices.
Remote powering of transmitter or receiver — For simplified installation, only one
power supply is necessary to power both devices.
Digital conversion of analog input signals — Analog signals are digitized, ensuring that
a reliable, high quality digital video signal is sent to the output destination.
EDID Minder — Automatically manages EDID communication between connected devices,
ensuring that all sources power up properly and reliably output content for display.
Key Minder — Authenticates and maintains continuous HDCP encryption between input
and output devices, verifying HDCP compliance for quick, reliable switching in professional
AV environments.
Compatible with all DTP HDMI 330 (230) and DTP DVI 330 (230) receivers, and
DTP 330- (230-) enabled products — The switching transmitters can be used with the
Extron IN1608, DTP CrossPoint 84, and other DTP 330- (230-) enabled products to meet
application requirements.
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 4
Installation
Installation Overview
Adapter Plates
Side Panel Featur
es
T
op Panel Features
Mounting
Operation
T
roubleshooting — If No Image Appears
Installation Overview
The DTP T FB unit is to be installed in an Ackermann GB3 (OBO Bettermann), MK Electric
CableLink Plus Modular, MK Electric CableLink Plus Single Pan, Electraplan, or PUK floor box.
CAUTION: Failure to check the items listed below may result in personal injury or
property damage.
ATTENTION : La non-vérication des éléments listés ci-dessous peut provoquer des
blessures ou dommages matériels.
1. Check that the installation of the floor box meets government, building, electrical, and
safety codes.
2. Install the floor box according to the instructions of the manufacturer.
3. Prepare and pull the cables through the floor box.
TIP: Secure cables with clamps or ties to provide strain relief.
4.
T
rim back and insulate shields with heat shrink.
ATTENTION:
To prevent short circuits, the outer foil shield can be cut back to the point
where the cable exits the cable clamp. Both braided and foil shields should be
connected to an equipment ground at the other end of the cable.
Afin d’éviter les court cir
cuits, le blindage en aluminium extérieur peut être
réduit jusqu’à ce que le câble sorte de la cosse de câble. Le blindage tressé et
le blindage en aluminium devraient être connectés à la masse d’un équipement
à l’autre bout du câble.
5.
Install the appr
opriate adapters to the desired position in the floor box (see Adapter
Plates on the next page).
6.
Connect cables to the side panel connectors located below the adapter plates (see
Connectors and Switch Below the Adapter Plates
on page 7).
7.
Mount the DTP T FB unit to the floor box (see
Mounting on page 10).
8.
Connect appr
opriate devices to the remaining side (see Connectors Above the
Adapter Plates on page 8) and top (see Top Panel Features on page 9) panel
connectors.
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 5
9. Configure the DTP T FB unit with SIS commands (see Simple Instruction Set Control
on page 19) or the Product Configuration Software (see Product Configuration
Software on page 26).
Adapter Plates
Each floor box model requires a specific pair of provided adapter plates to secure the device
to the box (see the table below for the appropriate adapter plates to use with certain floor
boxes).
Floor Box Adapter Plate Example
Ackermann GB3 (OBO Bettermann) 995241
995242
MK Electric CableLink Plus Single Pan 995243
MK Electric CableLink Plus Modular 995244
Electraplan 995300
PUK 995300
NOTE: The 995242 adapter plate is only used for position 2 of the Ackermann GB3
(OBO Bettermann) floor box.
1. Determine the position in the floor box to install the DTP T FB unit. Each compatible
floor box contains three positions to install devices (see figure 2).
NOTE: For the MK Electric CableLink Plus Single Pan floor box, do not use
position 2.
OBO Bettermann
GESR7 Floorbox Assembly
1
2
3
Figure 2. Example of Positions in a Floor Box
(Ackermann GB3 [OBO Bettermann] Shown)
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 6
2. Insert the top flange of the adapter plate into a mounting slot that is no higher than the
third slot from the top (see figure 3).
Figure 3. Installing an Adapter Plate (995241 Shown) into a Mounting Slot
NOTES:
Install adapter plates in
mounting slots of the
same position in the
floor box.
The MK Electric
CableLink Plus Single
Pan floor box does not
have mounting slots.
Use a mounting scr
ew
to secure the large
mounting hole of the
995243 adapter plate to
the mounting hole of the
floor box position (see
figure 4).
MK Electric
CableLink Plus
Single Pan Floor Box
995243
995243
Figure 4. Installing 995243 Adapter Plates
3. Rotate the adapter plate down so the bottom flange rests against the wall of the floor
box (see figure 5).
Figure 5. Fixing the Adapter Plate (995241 Shown) in Place
4. If the desired position is position 2 of the Ackermann GB3 (OBO Bettermann) floor box,
use the provided screws to secure the 995242 adapter plate to a 995241 adapter plate
(see figure 6).
Figure 6. Installing the 995242 Adapter Plate to a 995241 Adapter Plate
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 7
Side Panel Features
Connectors and Switch Below the Adapter Plates
DTP
DTP
HDBT
OUT
REMOTE
RS-232
POWER
1.0A MAX
12V
DTP T FB 332
+- G Rx Tx
LINK SIG
Side Panel
D
B
C
D
A
Figure 7. Side Panel Connectors and Switch Below the Adapter Plates
A
Power connector (see below)
B
Remote RS-232 port
C
TP connector
D
TP function switch (see the next page)
A
Power connector and LED — Plug the included external 12 VDC power
+-
1.0A MAX
12V
POWER
supply into either this 2-pole connector (see Power supply wiring on page 15 to
wire the connector). Or, power the receiver (see the DTP HDMI 330 User Guide
or DTP HDMI 230 User Guide, available at www.extron.com) and leave the TP
function switch in the DTP position.
NOTE: When the TP function switch (item
D
) is in the DTP position, one
power supply can power both units.
When the TP function switch is in the HDBT position, the transmitter
and receiver each requires a local 12 VDC power supply.
B
Remote RS-232 port — Plug a host device into the switching transmitter via
GRxTx
RS-232
the 3.5 mm, 3-pole captive screw connector for remote control of the
transmitter (see IR and RS-232 connector wiring on page 14 to wire the
connector).
9600 Baud 8 data bits No parity 1 stop bit
C
TP connector — Plug one end of a STP cable to this RJ-45 female jack.
LINK SIG
OUT
Plug the opposite end of this cable into the DTP Input RJ-45 connector on
a compatible receiver (see TP cable termination and recommendations
on page 13 to properly wire the RJ-45 connector and for detailed NOTES).
Signal LED indicator — Lights green when the transmitter outputs a video signal.
Link LED indicator — Lights yellow when XTP devices are connected and
communication is established.
ATTENTION:
Do not connect this connector to a computer data or telecommunications
network.
Ne connectez pas ces port à des données informatiques ou à un réseau
de télécommunications.
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 8
D
TP function switch (see figure 7 on the previous page) —
HDTP
DTP
ATTENTION:
Position this switch
BEFORE connecting the appropriate device to the TP
connector. Failure to comply can damage the endpoint.
Positionnez le sélecteur
AVANT de connecter l’appareil approprié au
connecteur TP. Ne pas respecter cette procédure pourrait endommager le
point de connexion.
If the connected receiving device is in the Extron DTP series, set this switch to the DTP
position. For an HDBaseT-enabled receiver type, set this switch to the HDBT position.
This switch tailors the output signal as follows:
HDBT position — The TP output consists of HDMI with embedded audio plus
RS-232 and IR.
DTP position — The TP output consists of HDMI with embedded audio, analog
audio, RS-232 and IR, and remote power.
NOTES:
When the switch is in the HDBT position, the transmitter and receiver
each requires a local 12 VDC power supply.
When the switch is in the DTP position
, one 12 VDC power supply,
connected to either the transmitter or the receiver, can power both units.
Connectors Above the Adapter Plates
DTP
HDBT
OUT
REMOTE
RS-232
POWER
1.0A MAX
12V
+- G Rx Tx
LINK SIG
Side Panel
F
E
Figure 8. Side Panel Connectors Above the Adapter Plates
E
HDMI input port — Plug a digital video source into the switching transmitter
via this HDMI port. It can accept HDMI or DVI (with an appropriate adapter)
video sources.
NOTES:
The maximum HDMI cable length is 15 feet (4.5 m).
Use an Extron LockIt lacing bracket to secure the HDMI connector to the
device (see HDMI Connectors on page 12).
F
Analog video input port — Connect an analog (RGB
RGB
or component) video source into the switching transmitter via this
15-pin HD connector (see VGA connector wiring on page 13 to for
connector pinout).
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 9
Top Panel Features
CONFIG
G
RS-232 IR
Rx
Tx
Tx
Rx
HDMI IN VGA IN
DTP T FB 332
HDMI
VGA
HDCP
AUTO
AUDIO IN
OVER DTP
RESET
Top Panel
A
B
C
D
Figure 9. Top Panel Features
A
Audio in connector (see below)
B
Over DTP port (see the next page)
C
Config(uration) port
D
Reset button
A
Audio In connector — If desired, plug
A
UDIO
an analog audio source into the
switching transmitter via this 3.5 mm
tip-ring-sleeve (TRS) jack. Both video inputs
can share this audio input.
NOTES:
See figur
e 10 to identify the connector
tip, ring, and sleeve when you are
making connections for the switching
transmitter from existing audio cables.
A mono audio connector consists of the
tip and sleeve. A stereo audio connector
consists of the tip, ring, and sleeve.
Sleeve ( )
Ring (
-
)
Tip (+)
3.5 mm Stereo Plug Connector
(balanced)
Figure 10. Wiring for TRS Connector
The analog audio can be assigned to
a specific input or set to be always
output (see
Assign analog audio SIS
command on page 22).
By default, audio input is selected automatically (see Assign analog audio SIS
commands on page 22 to manually select audio inputs). When the HDMI input is
selected with automatic audio input selection, the transmitter prioritizes embedded
digital audio. The following table shows the audio format that is sent over the DTP
connection when a specific audio format is not specified.
Selected
Video Input
HDMI Embedded
Audio Present
Analog Audio
Present
Audio Sent Over
TP Cable
VGA N/A Yes Analog audio
VGA N/A No No audio
HDMI Yes No HDMI embedded audio
HDMI Yes Yes HDMI embedded audio
HDMI No Yes Analog audio
HDMI No No No audio
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 10
B
Over DTP RS-232 and IR port (see figure 9 on the previous page—
RxTx RxTxG
RS-232 IR
Plug a serial RS-232 signal, a modulated IR signal (up to 40 kHz), or both
into this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232
and IR communication (see IR and RS-232 connector wiring on page 14
to wire the connector). RS-232 and IR data can be transmitted
simultaneously.
C
Config(uration) port — Connect a host device to the front panel mini USB B
CONFIG
configuration port. This port serves a similar communications function as the side
panel Remote RS-232 port, but it is easier to access than the side port after the
switcher has been installed and cabled.
NOTE: A top panel Configuration port connection and a side panel Remote RS-232
port connection can both be active at the same time. If commands are sent
simultaneously to both, the command that reaches the processor first is handled
first.
D
Reset button — Initiates two levels of reset of the switcher. For the different reset
RESET
levels, press and hold the button while the switcher is running or while you power
up the switcher (see Reset Mode on page 17 for details).
Mounting
Before mounting the floor box, consider the mounting location and prepare the surface as
necessary.
1. If not already completed, install the appropriate adapter plates in the desired position
and mounting slots (see Adapter Plates on page 5).
2. Align the screw holes on the DTP T FB unit with the screw holes on the adapter plates.
3. Using the provided self-threading screws and washers, secure the DTP T FB unit to the
adapter plates (see figures 11 though 14).
Ackermann GB3 (OBO Bettermann) Floor Box
DTP T FB 332
POWER
DTP T FB 332
REMOTE
RS-232
- +
G
Rx
Tx
12V
A MAX
XTP OUT
995242
995241
Figure 11. Mounting the Unit into an Ackermann GB3 (OBO Bettermann) Floor Box
NOTE: Position 2 requires the installation of the 995242 adapter plate on top of one of
the 995241 adapter plates.
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 11
MK Electric CableLink Plus - Single Pan Floor Box
DTP T FB 332
POWER
DTP T FB 332
REMOTE
RS-232
-
+
G
Rx
Tx
12V
A MAX
XT
POWER
DTP T FB 332
REMOTE
RS-232
12V
A MAX
995243
995243
Figure 12. Mounting the Unit into an MK Electric CableLink Plus - Single Pan Floor
Box
ATTENTION:
Do not install the DTP T FB 332 or DTP T FB 232 in position 2 (see figure 2 on
page 5).
Ne pas installer le DTPTFB332 ou DTP T FB 232 en position 2 (voir
l’illustration2
sur la page5).
MK Electric CableLink Plus - Modular Floor Box
DTP T FB 332
POWER
DTP T FB 332
REMOTE
RS-232
-
+
G
Rx
Tx
12V
A MAX
XTP OUT
995244
995244
Figure 13. Mounting the Unit into an MK Electric CableLink Plus - Modular Floor Box
DTP T FB 332 and DTP T FB 232 Twisted Pair Transmitters • Installation 12
Electraplan or PUK Floor Box
DTP T FB 332
POWER
XTP T FB 202
REMOTE
RS-232
-
+
G
Rx
Tx
12V
A MAX
XTP OUT
995300
995300
Figure 14. Mounting the Unit into an Electraplan or PUK Floor Box
Connection and Wiring Details
HDMI connectors
Use the Extron LockIt Lacing Bracket, supplied with the switcher, to securely fasten the
HDMI cable to the device. The LockIt lacing bracket can be applied to the top or the side
mounting screws. The following directions describe how to attach a LockIt lacing bracket to
the top mounting screw (see figure 15):
1. Plug the HDMI cable into the panel connection (see figure 15,
1
).
3
33
11
44
55
22
Figure 15. Installing the LockIt Lacing Bracket
2. Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it (
2
). The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then
tighten the screw to secure the bracket (
3
).
ATTENTION:
Do not overtighten the HDMI connector mounting screw. The shield to which it
fastens is very thin and can easily be stripped.
Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel
elle est attachée est très fin et peut facilement être dénudé.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket (
4
).
5. While holding the connector securely against the lacing bracket, use pliers or similar
tools to tighten the tie wrap (
5
), then remove any excess length.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Extron DTP T FB 332 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues