Whirlpool WFW9550WW01 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WFW9550WW01

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

FRONT.LOADING

AUTOMATICWASHER

For questions about features, operation/performance,

parts, accessories, or service call: 1-800-253-1301

In Canada, call: 1-800-807-6777

or visit our website at

www.whirlpool.com or www.whirlpool.ca

LAVEUSE

AUTOMATIQUEA

CHARGEMENTFRONTAL

Au Canada, pour assistance, installation ou service, composez le :

1-800-807-6777

ou visitez notre site Internet & www.whirlpool.ea

Table of Contents/Table des matieres .................. 2

Certified to Sanitize

Homologu6 pour assainir

Designed to use only HE High Efficiency Detergent

Con(_ue pour I'utilisation d'un d6tergent haute efficacit6

seulement

W10251899C

TABLEOFCONTENTS

WASHER SAFETY ......................................................................... 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Options ......................................................................................... 4

Location Requirements ................................................................ 5

Drain System ................................................................................ 6

Electrical Requirements ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 7

Remove Transport System .......................................................... 7

Connect the Inlet Hoses ............................................................... 8

Connect the Drain Hose ............................................................... 8

Secure the Drain Hose ................................................................. 9

Level the Washer .......................................................................... 9

Complete Installation ................................................................... 9

FEATURES AND BENEFITS ........................................................ 10

WASH ER USE ............................................................................... 11

Starting Your Washer ................................................................. 11

Using the Proper Detergent ....................................................... 11

Using the Dispenser ................................................................... 12

Pausing or Restarting ................................................................. 13

Changing Cycles, Options, and Modifiers ................................. 13

Status Lights .............................................................................. 13

Cycles ......................................................................................... 14

Normal Washer Sounds ............................................................. 15

Options ....................................................................................... 16

Modifiers ..................................................................................... 16

Laundry Guide ............................................................................ 17

LAUNDRY TIPS ............................................................................ 18

Loading ....................................................................................... 18

WASHER CARE ............................................................................ 19

Cleaning Your Washer ............................................................... 19

Water Inlet Hoses ....................................................................... 19

Vacation, Storage, and Moving Care......................................... 20

TROUBLESHOOTING .................................................................. 21

ASSISTANCE OR SERVICE ......................................................... 24

In the U.S.A................................................................................ 24

In Canada ................................................................................... 24

Accessories ................................................................................ 24

WAR RANTY .................................................................................. 25

TABLEDESMATIERES

SleCURITle DE LA LAVEUSE ........................................................ 26

EXIGENCES D'INSTALLATION ................................................... 27

Outillage et pieces ...................................................................... 27

Options ....................................................................................... 27

Exigences d'emplacement ......................................................... 28

Systeme de vidange ................................................................... 29

Specifications electriques .......................................................... 30

INSTRUCTIONS D'INSTALLATION ............................................. 31

I_limination des accessoires de transport .................................. 31

Raccordement des tuyaux d'alimentation ................................. 31

Raccordement du tuyau de vidange .......................................... 32

Immobilisation du tuyau de vidange .......................................... 32

Reglage de I'aplomb de la laveuse............................................ 33

Achever I'installation .................................................................. 33

CARACTg:RISTIQUES ET AVANTAGES ..................................... 34

UTILISATION DE LA LAVEUSE ................................................... 35

Mise en marche de la laveuse.................................................... 35

Utilisation du detergent approprie ............................................. 35

Utilisation du distributeur ........................................................... 36

Pause ou remise en marche ....................................................... 37

Changement des programmes, options et modificateurs ......... 38

T6moins lumineux ...................................................................... 38

Programmes ............................................................................... 39

Sons normaux emis par la laveuse ............................................ 41

Options ....................................................................................... 41

Modificateurs .............................................................................. 42

Guide de lessivage ..................................................................... 43

CONSEILS DE LESSIVAGE .......................................................... 44

Chargement ................................................................................ 44

ENTRETIEN DE LA LAVEUSE ..................................................... 44

Nettoyage de la laveuse ............................................................. 44

Tuyaux d'arrivee d'eau ............................................................... 45

Precautions h prendre avant les vacances,

un entreposage ou un dem6nagement ...................................... 46

DlePANNAGE ................................................................................. 46

ASSISTANCE OU SERVICE ......................................................... 50

Aux #tats-Unis ............................................................................ 50

Au Canada .................................................................................. 50

Accessoires ................................................................................ 50

GARANTIE ..................................................................................... 51

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injuryto persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. Ifthe hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where it will be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

[] See "Electrical Requirements" for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

• Pliers (that open to 19/16"[39.5 mm])

• Flashlight (optional)

Tools needed for connecting the drain hose

• Locking pliers (that open to 19/16"[39.5 mm])

Tools needed for installation

• Open end wrenches 17 mm and 13 mm

• Level

• Wood block

• Ruler or measuring tape

Parts supplied:

A. Drain hose form

B. Inlet hose (2)

C. Inlet hose washer (4)

D. Transport bolt hole plug (4)

E.Beaded strap

E Drain hose

G. Hose clamp

Alternate Parts

Your installationmay require additional parts. If you are interested in

purchasing one of the items listed here, call the toll-free number on

the cover or in the "Assistance or Service" section.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (ifnot already

standpipe taller than available)

96" (2.4 m)

Overhead sewer

Floor drain

Standard 20 gal. (76 L), 30" (762 mm) tall

drain tub or utility sink and sump pump

(available from local plumbing suppliers)

Siphon break, Part Number 285834;

additional drain hose Part Number

8318155; and connector kit, Part Number

285835

Drain hose too short 4 ft (1.2 m) drain hose extension kit, Part

Number 285863

Water faucets 2 longer water fill hoses: 6 ff (1.8 m) Part

beyond reach of fill Number 76314, 10 ft (3.0 m) Part

hoses Number 350008

Pedestal

You have the option of purchasing pedestals of different heights

separately for this washer. You may select a 10" (254 mm) or a

15.5" (394 mm) pedestal. These pedestals will add to the total height

of the washer for a total height of approximately 48" (1219 mm) or

53.5" (1359 mm), respectively.

A. 10" (254 mm) pedestal

B. 15.5" (394 mm) pedestal

Toorder, call the dealer from whom you purchased your washer or

refer to the "Assistance or Service" section.

Pedestal Color Part Number

Height

10" (254 mm) White WHP1000SQ

10" (254 mm) Black WHP1000SB

10" (254 ram) Diamond Dust (Silver) WHP1000SU

15.5" (394 ram) White XHP1550VW

15.5" (394 ram) Black XHP1550VB

15.5" (394 ram) Diamond Dust (Silver) XHP1550VU

15.5" (394 ram) New Aspen (Light Green) XHP1550VA

15.5" (394 ram) Tuscan Chestnut XHP1550VC

15.5" (394 ram) Ocean Blue XHP1550VE

15.5" (394 ram) Cranberry Red XHP1550WR

15.5" (394 ram) Lunar Silver XHP1550WL

Stack Kit

Are you planning to stack your washer and dryer? Todo so you

will need to purchase a Stack Kit.

Toorder, call the dealer from whom you purchased your dryer

or refer to the "Assistance or Service" section. Ask for Part

Number 8541503.

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer "walk."

Your washer can be installed under a custom counter, or in a

basement, laundry room, closet, or recessed area. See "Drain

System."

Companion appliance location requirements should also

be considered. Proper installation is your responsibility.

You will need

• A water heater set to deliver 120°F (49°C) water to the

washer.

• A grounded electrical outlet located within 6 ft (1.8 m) of

where the power cord is attached to the back of the washer.

See "Electrical Requirements."

• Hot and cold water faucets located within 4 ft (1.2 m)

of the hot and cold water fill valves, and water pressure

of 20-100 psi (137.9-689.6 kPa).

• If you live in a hard water area, use of awater softener is

recommended to control the buildup of scale in the steamer

and other areas of the washer. Over time, the buildup of lime

scale may clog the steamer, which will reduce steamer

efficiency and performance. Excessive buildup of scale may

lead to the need for steamer replacement or repair.

• A level floor with a maximum slope of 1" (25 mm) under entire

washer. Installing the washer on soft floor surfaces, such as

carpets or surfaces with foam backing, is not recommended.

• A sturdy and solid floor to support the washer with a total weight

(water and load) of 400 Ibs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C).

Some water can remain in the washer and can cause damage in low

temperatures.

Recommended installation spacing for custom

undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

'HI M''P '1

39"rain.

(25ram) (666ram) (25ram)

Recommended installation spacing for recessed

or closet installation, with or without a pedestal

The dimensions shown are for the recommended spacing.

Recessed area or closet installation

- f

34"rain.

-- (864

1"--_11_'--32"-_q4" _--

(25ram} (813ram}(102mm}

48in.2L_

(310cm2)

24in,2

(155cm2}

.__ 3"

(76ram)

Installation clearances

• The location must be large enough to allow the washer door

to be fully opened.

• Additional spacing should be considered for ease of installation

and servicing.

• Additional clearances might be required for wall, door, and

floor moldings.

• Additional spacing of 1" (25 mm) on all sides of the washer

is recommended to reduce noise transfer.

• Companion appliance spacing should also be considered.

Washer Dimensions

51"

_(1295

A.Side view -closet or confinedarea

B.Closetdoor with vents

*Min. top and bottom air openings for closet door.

Recessed or closet installation - Washer on pedestal

._.

-- 18" mln,

(457mm)

_%-._

, v

(25ram} (686ram} (25ram} (813ram}(102ram}

A B

A.Recessedarea

B. Sideview- closet or confinedarea

Recommended installation spacing for recessed or

closet installation, with stacked washer and dryer

Thedimensionsshownarefor therecommendedspacing.

3I*

(76ram)

3 II_

"-__ (78_m)

(25ram)

*Required spacing

6"*(152ram}

[

78"

(193imm)

51/2" _ _ 1 "*"_

{140ram) {25mm)

\ _.__J/

(888ram} (25ram}

*Required spacing

**For venting out the side, 1" (25 mm) spacing is allowed.

Recommended installation spacing

for cabinet installation

• The dimensions shown are for the recommended spacing.

• For cabinet installation with a door, the minimum ventilation

openings in the top are required.

"_/7" (178ram)

_ 7"(178ram)

(102ram}

_--l"-:,,qI_---27"-----_I_-1"

(813ram} (25ram} (686ram} (25ram)

The washer can be installed using the standpipe drain system

(floor or wall), the laundry tub drain system, or the floor drain

system. Select the drain hose installation method you need.

See "Tools and Parts."

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of

2" (50 mm). The minimum carry-away capacity can be no less than

17 gal. (64 L) per minute.

The top of the standpipe must be at least 30" (762 mm) high and

no higher than 96" (2.4 m) from the bottom of the washer.

30"rain.

(702mm}

A B

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 30" (762 mm) above the floor.

Floor drain system (view D)

The floor drain system requires a siphon break that may be

purchased separately. See "Tools and Parts."

The siphon break must be a minimum of 28" (711 mm) from the

bottom of the washer. Additional hoses might be needed.

C D

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is recommended that a separate circuit

serving only this appliance be provided.

• This washer is equipped with a power supply cord having

a 3 prong grounding plug.

• To minimize possible shock hazard, the cord must be

plugged into amating, grounded 3 prong outlet, grounded

in accordance with local codes and ordinances. Ifa mating

outlet is not available, it is the personal responsibility and

obligation of the customer to have the properly grounded

outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the

washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING iNSTRUCTiONS

For a grounded, cord=connected washer:

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electdc

current. This washer is equipped with a cord having an

equipment=grounding conductor and a grounding plug. The

plug must be plugged intoan appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance -if itwill

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the washer

is within approximately 3 ft (900 ram) of its final location.

There are 4 bolts in the rear panel of the washer that support the

suspension system during transportation. These bolts also retain

the power cord inside the washer until the bolts are removed.

1. Using a 13 mm wrench, loosen each of the bolts.

Once the bolt is loose, move it to the center of the hole and

completely pull out the bolt, including the plastic spacer

covering the bolt.

3. Once all 4 bolts are removed, discard bolt and spacers. Then pull

the power cord through the opening of the rear panel and close

the hole with the attached cap.

4. Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your

local service center. To avoid suspension and structural damage

to your washer, it must be properly set up for relocation by a

certified technician.

_;_, _1_ _, ,_;,.......

Insert new flat washers (supplied) into each end of the inlet hoses.

Firmly seat the washers in the couplings.

A B

A. Coupling

B. Washer

2. Make sure the washer drum is empty.

3. Attach the hose with the red color indicator to the Hot (left) inlet

valve. Attaching the red coupling first makes it easier to tighten

connection with pliers. Screw on coupling by hand until it is

seated on the washer.

4. Attach the hose with the blue color indicator to the Cold (right)

water inlet valve. Screw on coupling by hand until it is seated

on the washer.

H.Hot waterinlet

C.Cold waterinlet

5. Using pliers, check the tightness of the hose couplings already

attached to the washer.

NOTE: Do not overtighten. Damage to the coupling can result.

6. Attach hot water hose to the hot water faucet. Screw on coupling

by hand until it is seated on the washer.

7. Attach cold water hose to the cold water faucet. Screw on

coupling by hand until it isseated on the washer.

8. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

9. Turn on the water faucets and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Remove drain hose from washer drum

1. Use locking pliers, squeeze hose clamp tabs together and insert

over the end of drain hose.

2. Slide drain hose onto washer connection.

3. Once drain hose is in place, release pliers.

4. Washer drain system can be installed using afloor drain, wall

standpipe, floor standpipe, or laundry tub.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose.

A B

A.Snapeitherend of thedrainhose form to thedrain hose

at thepoint where thecorrugationbegins.

B.Benddrainhoseover drainhose form andsnap intoplace.

To keep drain water from going back into the washer:

• Do not straighten the drain hose, and do not force excess drain

hose into standpipe. Hose should be secure, but loose enough

to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See Floor drain under "Tools and

Parts."

Drape the power cord over the washer top.

Secure the drain hose to the laundry tub leg or standpipe with

the beaded strap provided. (See illustrations A and B.)

B C

If the washer faucets and the drain standpipe are recessed

(see illustration C), put the hooked end of the drain hose in

the standpipe. Tightly wrap the beaded strap around the

water inlet hoses and the drain hose.

Do not force excess drain hose into the standpipe.

Properly leveling your washer avoids excessive noise and vibration.

1. Check the levelness of the washer by placing a level on the

top edge of the washer, first side to side, then front to back.

If the washer is against a wall, move the washer out slightly

before tipping back. If the washer is not level, first prop the

front with a wood block and adjust the feet as necessary;

then prop the back and adjust feet as necessary. Repeat this

step until washer is level.

2. Make sure all four feet are stable and resting on the floor.

Then check that the washer is perfectly level(use a level).

3. After the washer is level, use a 17 mm open-end wrench to

turn the nuts on the feet tightly against the washer cabinet.

IMPORTANT: All four feet must be tightened. Ifthe nuts are

not tight against the washer cabinet, the washer may vibrate.

4. The washer should not move front to back, side to side,

or diagonally when pushed on its top edges.

5. Slide the washer to its final location.

6. Confirm the levelness of the washer.

1. Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding

method. See "Electrical Requirements."

2. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug into a grounded 3 prong outlet.

Read "Washer Use."

Totest and clean your washer, make sure there areno clothes in

the washer and add one AFFRESH <etablet to the washer drum.

Select Power, the Clean Washer cycle and then select START.

This cycle will take approximately 65 minutes to complete. Allow

the washer to complete the entire cycle without interruption.

FEATURESANDBENEFITS

Electronic Controls

Flexible electronic controls are easy to use whether you are a

beginner or an expert.

Smart Dispensers

The Smart Dispensers make your washer truly automatic. This

washer provides a three-compartment dispenser which includes

separate compartments for main wash detergent, fabric softener,

and bleach. The dispenser has large pour zones. The dispenser is

self-cleaning, and can be easily removed. Laundry products are

diluted with fresh water and added to the load at the proper time

in the wash cycle.

Deep Clean with Steam

This washer has a built-in steaming unit which is combined with

the DEEP CLEAN option to provide multiple temperatures to help

remove a variety of stains from garments.

Clean Washer With AFFRESH TM Cycle with Steam

This cycle uses steam to raise the temperature of the washer and

makes the washer self-cleaning, flushing the machine's interior

free of dirt and other residue. The use of AFFRESH_washer cleaner

or liquid chlorine bleach with this cycle will remove and help avoid

odor-causing residue.

Auto Water Level

This washer automatically adjusts water level for optimal cleaning

and rinsing performance. Two sensors determine load size, load

composition, and suds level, then the sensors adjust the water

level to the proper setting. This eliminates guesswork. The water

level is just right for every wash load size.

Larger Load Size

Because there is no agitator, you can wash larger, bulkier items such

as a king-sized bedspread. You are also able to wash more clothes

at one time, which means fewer loads.

Stainless Steel Drum

The stainless steel drum eliminates corrosion and enables higher

spin speeds for more water extraction, helping to reduce drying

time compared to traditional top-load washers.

High-Efficiency Wash System

Your new front-loading, high-efficiency washer saves time with

fewer, larger loads. Italso lowers your water and energy bills by

helping conserve resources.

Spin Speeds

This washer automatically selects the spin speed based on the

cycle selected. This factory setting can be changed, however.

This washer offers up to five different spin speed choices, up to

1300 rpm.

Heating Element

This washer has a heating element that automatically heats the

water to the optimal temperature on select cycles. This enables

stepped cleaning, a process in which warm water is brought in

and mixed with detergent first, then the water is heated. Stepped

cleaning starts the wash cycle with warm water to remove stains

(such as blood and grass).

6th SENSE ° Intuitive Controls

Intuitive intelligence "knows every load" determining load sizes,

water levels, and how much cleaning time is needed.

sense '°

Add A Garment

When this option is available at the beginning of the cycle, the

Add A Garment Status Light will glow for the first 4-8 minutes.

This washer allows a 4-8 minute period in which other garments

may be added to a load.

Direct Injection Wash System

This washer channels 100% of the water through the dispensers

to assure thorough rinse-out and mixture of all the laundry

products before they touch any garments. The water is then

sprayed from the top front onto the center of the load, providing

even distribution and optimum cleaning performance. It is normal

for small amounts of water to remain in the dispensers when the

wash cycle is complete.

Efficient Detergent System with Anti-Escape Valve

This washer has a specially designed valve that closes during

the wash portion of the cycle so that 100% of the water and

detergent mixture is used on the load. The Efficient Detergent

System ensures that no water or detergent is wasted.

6-Point Suspension System

Shock absorbers, 2 springs, and electronic controls are specially

designed to help redistribute the load automatically and minimize

movement of the wash drum during the spin cycle. The 6-Point

Suspension System reduces the amount of force transmitted to

the floor by the washer, resulting in reduced noise and vibration.

WASHERUSE

NOTE: The panel shown above may be different from that of your model.

DelayWash

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injuryto

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

The following is a guide to using your washer. Please refer to

specific sections of this manual for more detailed information.

Do not store laundry products on the top surface of this washer.

Vibration is normal during operation.

Use only High Efficiency detergents. The package for this type

of detergent will be marked "HE" or "High Efficiency." This wash

system, along with less water, will create too much sudsing with

a regular non-HE detergent. Using regular detergent will likely

result in washer errors, longer cycle times, and reduced rinsing

performance. It may also result in component failures and noticeable

mold or mildew. HE detergents are made to produce the right

amount of suds for the best performance. Follow the manufacturer's

instructions to determine the amount of detergent to use.

Remember, concentrated detergents such as 2x or higher will use

less detergent based on load size.

Use only High Efficiency (HE) detergent.

First Wash Cycle Without Laundry

Before washing clothes for the first time, if not completed during

the final installation step, choose the QUICK WASH cycle and run

it without clothes. Use only HE detergent. Use 1/,..

the manufacturer's recommended amount for a medium-size load.

This initial cycle serves to ensure the interior is clean before

washing clothes.

For AllWash Cycles

Open the washer door by pulling on the handle. Sort laundry

according to color and type of fabric. Place a load of sorted

clothes in the washer. Do not overload washer. Overloading

can cause poor cleaning.

• The washer can be fully loaded, but not tightly packed.

Washer door should close easily.

Mix large and small items and avoid washing single items.

Load evenly.

Wash small items, such as infant socks, in mesh garment

bags. It is recommended that more than one garment bag

be used, and that each garment bag be filled with equal

amounts of material.

• When unloading garments, occasionally check under the

gray colored seal at the front of the tub for small items.

Close the washer door by pushing it firmly until the lock clicks.

The washer door will remain locked during the wash cycle.

NOTES:

After any wash cycle is completed, the door must be

opened and then closed before a new cycle can begin.

The door can be opened only if PAUSE/CANCEL is

selected while the Add A Garment light is glowing or if

the cycle has been canceled.

See "To cancel a cycle" in "Changing Cycles, Options,

and Modifiers" section.

Open the dispenser drawer and add laundry products to the

detergent, bleach, or fabric softener compartments. Close drawer

slowly to avoid spills. See "Using the Dispenser."

Turnon the washer by selecting POWER. Select one of the cycles

by turning the cycle selector. The indicator light for the selected

cycle will glow green. When you areselecting a wash cycle, the

preset options and modifiers (suchas Water Temp, Spin Speed,

Soil Level, and Rinse)for the selected cycle will glow green.

Selectable options will glow amber. If an option or modifier is

unavailable with aselected cycle, the light will not illuminate.

The display shows the estimated time remaining. The preset

settings provide the recommended fabric carefor the selected

cycle. See "Cycles."

5. Select the desired Options. Not all options areavailable with

all cycles. See "Options."

6. Select the desired modifiers such as Water Temp, Spin Speed,

Soil Level, and Rinse. Not all modifiers are available with all cycles

and options. See "Modifiers."

7. If desired, select the CYCLE SIGNAL. The signal is helpful

when you are washing items that should be removed from the

washer as soon as it stops. Select Loud, Soft, or Off.

8. If desired, select the BU-I-I-ONSOUND. This feature makes a

sound each time a button is pressed. Select Loud, Soft, or Off.

9. Select and hold START for approximately 1 second.

• If you do not select START within 5 minutes of choosing

a cycle, the washer automatically shuts off.

When the wash cycle is complete, the DONE status light

glows, the door unlocks, and the wash load can be

removed from the washer. The washer powers down

automatically 60 minutes after the cycle is complete

and the DONE light goes off. To power down the washer

manually after the wash cycle is complete, select PAUSE/

CANCEL once.

10. To use the same cycle again, press POWER first, then select

START.

11. To begin the wash cycle later

Select DELAY WASH until the desired delay time (in hours)

shows in the Estimated Time Remaining display. Select START.

The countdown to the wash cycle will show in the display

window.

IMPORTANT: When delaying a cycle, use only powdered

detergents in the main wash compartment since liquid

detergents may seep out of the compartment during Delay

Wash, before the wash cycle begins.

Your new washer has a dispenser drawer with three separate

compartments for your laundry products--one is for detergent,

one is for liquid chlorine bleach, and one is for liquid fabric

softener. Laundry products are diluted and dispensed

automatically at the proper time during the wash cycle,

making it unnecessary for you to return to the washer during

the cycle to add them.

It is normal for small amounts of water to remain in the

dispensers when the wash cycle is complete.

Do not put laundry products directly into the wash tub. Always

use the proper dispensers when adding laundry products.

Choosing the Right Detergent

Use only High Efficiency detergents. The package for this type of

detergent will be marked "HE" or "High Efficiency." This wash

system, along with less water, will create too much sudsing with a

regular non-HE detergent. Using regular detergent will likely result

in washer errors, longer cycle times, and reduced rinsing

performance. It may also result in component failures and

noticeable mold or mildew. HE detergents are made to produce

the right amount of suds for the best performance. Follow the

manufacturer's instructions to determine the amount of detergent

to use. Remember, concentrated detergents such as 2x or higher

will use less detergent based on load size.

Use only HE High Efficiency detergenL

Tofill dispenser compartments

1. Pull out the dispenser drawer.

2. Add the desired laundry product to the proper compartment.

3. Push in the dispenser drawer slowly and completely (to avoid

a spill).

Dispenser

A. Detergent type selector

B. Main Wash detergent compartment

C. Dispenser release lever

D. Chlorine bleach compartment

E. Fabric softener compartment

Main Wash detergent compartment

(Letter B in Dispenser Illustration)

Add liquid or powdered HE detergent to this compartment for

your main wash cycle. The detergent type selector (A) must

always be in the correct position for the detergent type used. Slide

the detergent type selector to the correct position.

IMPORTANT: If you are using the Delay Wash option, powdered

detergent must be used in the Main Wash compartment, since

liquid detergents may seep out of the Main Wash compartment

before the main wash begins.

• Use the detergent manufacturer's recommended amount for

load size.

• Liquid or powdered color-safe bleach may be added to the Main

Wash compartment along with the same type of detergent,

liquid or powdered.

• Liquid detergent:

Selector in position for fiquid detergent

A. Detergent type selector

• Powdered detergent:

Selectorin position for powdered detergent

A.Detergent type selector

Chlorine bleach compartment

(Letter D in Dispenser Illustration)

Add no more than 2/3cup (160 mL) liquid chlorine bleach to this

compartment. The bleach will be automatically diluted and

dispensed at the optimum time during the first rinse after the wash

cycle. This compartment cannot dilute powdered bleach.

• Always measure liquid chlorine bleach. Use a measuring cup

with a pour spout; do not guess.

• Do not fill beyond the"MAX" level.

NOTE: Overfilling could cause garment damage.

At the end of the cycle, a small amount of water may be left in

the dispenser. This is normal.

Fabric softener compartment

(Letter E in Dispenser Illustration)

Pour measured liquid fabric softener into the fabric softener

dispenser, if desired.

IMPORTANT: Dilute all fabric softener with water for atotal of

1/4cup (60 mL).

• Do not overfill. The dispenser holds 1/4cup (60 mL).

• Do not spill or drip any fabric softener onto the clothes.

NOTES:

• Use only liquid fabric softener in this dispenser.

Do not use fabric softener dispensing balls in this washer.

Dispensing balls will not operate correctly with this washer.

1. To pause the washer at any time, press PAUSE/CANCEL

2. To continue the cycle, press START (for approximately 1second).

Not all Options and Modifiers are available with all cycles.

Available modifiers will glow amber. If an option or modifier is

unavailable with aselected cycle, the light will not illuminate.

Cycles, Options, and Modifiers can be changed anytime before

START is selected.

To cancel a cycle and select a new cycle

1. Press PAUSE/CANCEL twice.

2. Press POWER.

3. Select desired cycle.

4. Select the desired Options or modifiers such as Water Temp,

Spin Speed, and Soil Level.

5. Press START(for approximately 1 second) to restart the washer

at the beginning of the new cycle.

To cancel a cycle

1. Press PAUSE/CANCEL twice.

2. The washer powers down, the door unlocks, and clothes can

be removed.

NOTE: If the water levelor the temperature istoo high, the washer

will drain automatically before the door unlocks.

To change Options or Modifiers after the cycle has

started

1. Press PAUSE/CANCEL once.

2. Select the desired Options or Modifiers such as Water Temp,

Spin Speed, and Soil Level.Available selections will glow amber.

3. Press START(for approximately 1 second) to continue the cycle.

To drain the washer manually

1. Press PAUSE/CANCEL twice.

2. Press POWER.

3. Select DRAIN/SPIN.

4. Press START(for approximately 1 second) to begin the drain.

5. When the spin is complete, the door unlocks. Items can be

removed from the washer.

These lights show which portion of the cycle the washer is

operating. They also indicate when you can add an additional

item to the wash cycle and when the controls are locked.

EstimatedTimeRemaining

Add A Garment

This washer allows a 4-8 minute period in which other garments

may be added to the load. You can add items to the washer if the

Add A Garment status light is glowing.

Toadd items when Add A Garment light is glowing

1. Select PAUSE/CANCEL once. The washer door unlocks after

afew seconds, and items can be added.

2. To continue the cycle, close the door and select and hold

START (for approximately 1 second).

Toadd items when the Add A Garment light is not glowing

1. You must cancel the current cycle by pressing PAUSE/CANCEL

twice. This will cancel the wash cycle and options. The washer

door unlocks, and items can be added.

2. Close the door, press POWER, and select the new cycle and

options. Select and hold START (for approximately 1second).

Done

The Done status light stays on for 60 minutes after the cycle is

complete, and then the washer shuts off.

Sanitized

This washer has a Sanitize water temperature that is certified

by NSF International, an independent third-party testing and

certification organization. The certification verifies that the

sanitizing cycle reduces 99.9% of bacteria typically found

on clothing, bedding, and towels, and there is no carryover

of bacteria between loads after the cycle is complete.

Cycles can be selected by turning the Cycle Control knob to the

desired cycle. Each cycle is designed for different types of fabric

and soil levels. The modifier indicator lights, on the right-hand

side of the panel, will change as cycles are selected.

NORMAL

HAND ACTIVEWEAR

WASHABLES BULKYITEMS

QUICKWASH HEAVYDUTY

wAsHcYcLes WHITEST

WHITES

Certified to Sanitize

If the "Sanitize" wash temperature was selected, when the wash

cycle is complete, the DONE status light will illuminate, the door

unlocks, and the wash load can be removed from the washer.

The washer powers down automatically 60 minutes after the

cycle is complete and the DONE status light turns off. Only cycles

with sanitize wash temperature selected have been designed to

meet the requirements of NSF Protocol P172 for Sanitizing

Efficacy.

Controls Lock/Unlock

The Controls Lock avoids unintended use of the washer. You can

also use the control lock feature to avoid unintended cycle or

option changes during a cycle. When Controls Lock is lit, all

buttons are disabled except for Pause/Cancel and Start. You can

lock the controls while the washer is operating.

To lock the controls

Press and hold CONTROLS LOCK/UNLOCK for 3 seconds after the

cycle starts, or when the washer is turned off.

ControlsLock/Unlock

Holdfol 3Seconds

The status light next to the CONTROLS LOCK/UNLOCK button

will glow.

To unlock the controls

Press and hold CONTROLS LOCK/UNLOCK for 3 seconds until

the status light turns off.

NOTE: To lock or unlock the controls when the washer is off,

press and hold CONTROLS LOCK/UNLOCK for 3 seconds.

Door Locked

Whenthe status lightglows,the door is locked.

Sensing/Revising Estimated Time

The cycle times vary automatically based on your water pressure,

water temperature, detergent, and clothes load.

The washer will automatically sense the progress in the cycle and

adjust the Estimated Time Remaining display. While the washer is

sensing, the estimated time will flash and the Sensing status light

will glow. When the sensing is complete, the flashing stops, the

status light goes off, and the Estimated Time Remaining display

is updated.

The cycle time will be extended if oversudsing occurs or the load

is unbalanced. The SUD routine removes extra suds and assures

proper rinsing of your garments. See "Troubleshooting." During

the unbalance routine, the time displayed may pause until this

activity is complete, then resume with the remainder of the cycle.

:[INSE/ SPIN

CLEANWASHER SOAK

w,th_resh

• Each cycle has a preset Soil Level (estimated cycle time),

Water Temperature, and Spin Speed, and may have preset

options. The preset settings provide the recommended fabric

care for the selected cycle.

• The preset settings will glow green to show the preselected

options and modifiers, and can be changed anytime before

START ispressed. Not all options and modifiers are available

with all cycles. Available selections glow amber. (Tochange

settings after the cycle has started, press PAUSE/CANCEL

once, then select the desired settings. Press START to continue

the cycle.)

• Powdered detergents may not dissolve well in aslow-speed

cycle. For best results, use liquid detergent inslow-speed

cycles.

Preset cycle settings

Each cycle has a preset Soil Level (cycle time), Water Temperature,

and Spin Speed. The preset settings provide the recommended

fabric care for the selected cycle. See chart.

Cycle Soil Level Water Temp Spin Speed

(cycle time)

Whitest Norm al Hot/Cold High

Whites (1:20)

Heavy Duty Normal Hot/Cold High

(1:1O)

Bulky Items Normal Warm/Cold Low

(0:55)

Active Wear Normal Warm/Cold Medium

(0:40)

Normal/ Normal Warm/Cold High

Casual (0:50)

Delicate Normal Warm/Cold Medium

(0:40)

Hand Normal Cold/Cold Low

Washables (0:30)

Quick Wash Light Warm/Cold High

(2-3 items) (0:18)

Clean N/A N/A N/A

WasherWith (1:05)

AFFRESN TM

Cycle Soil Level Water Temp Spin Speed

(cycle time)

Soak Normal Warm/Cold No Spin

(0:32)

Rinse/Spin N/A Warm/Cold High

(0:22)

Drain/Spin N/A N/A High

(0:13)

To change the preset cycle settings

Press the selector of each available setting until the desired

setting glows green.

Whitest Whites

This cycle is especially designed for cleaning loads of soiled white

fabrics with the addition of bleach. Hot washing temperatures

assure optimal bleach activity. An additional rinse provides optimal

rinse performance to avoid chlorine residues on your laundry.

This cycle combines fast-speed tumbling, longer wash time,

and high speed spin to shorten drying time.

Heavy Duty

Use this cycle to wash loads of sturdy, colorfast fabrics and heavily

soiled garments. This cycle combines fast-speed tumbling, longer

wash time, and high speed spin to shorten drying times. If the water

temperature is lower than needed for this cycle, the heater will warm

the water to the optimum temperature.

Bulky Items

Use this cycle to wash large items such as blankets and comforters.

This cycle starts with a soak to thoroughly saturate your large load.

This is followed by medium wash action and low-spin speeds to

maintain load balance.

Active Wear

Use this cycle to wash small loads of exercise wear such as biking

shorts, tank tops, running tights, and other performance clothing.

This cycle combines low-speed tumbling and medium-speed spin

for gentle fabric care.

Normal/Casual

Use this cycle to wash loads of no-iron fabrics, such as sport shirts,

blouses, casual business clothes, permanent press blends,

cottons and linens, and synthetic fabrics. This cycle combines

medium-speed tumbling, high-speed spin, and a load cooling

process to reduce wrinkling.

NOTE: For the best energy performance, use the Normal/Casual

Cycle.

Delicate

Use this cycle to wash sheer fabrics and lingerie. This cycle

combines low-speed tumbling and medium-speed spin for gentle

fabric care.

Hand Washables

Use this cycle to clean hand washable and special-care garments.

Similar to the way garments are hand washed in a sink, the wash

action of this cycle combines periods of low-speed tumbling and

soaking. Low-speed spin reduces wrinkling.

• Use meshgarment bagsasnecessary.

Quick Wash

Use this cycle to wash small loads of 2-3 lightly soiled garments

that are needed in a hurry. This cycle combines fast-speed tumbling,

a shortened wash time, and high speed spin to shorten

drying time.

Clean Washer With AFFRESH TM cycle

Use the Clean Washer With AFFRESH TM cycle once a month to

keep the inside of your washer fresh and clean. This cycle uses a

higher water level. Use with AFFRESH _ewasher cleaner tablet or

liquid chlorine bleach to thoroughly clean the inside of your washing

machine. This cycle should not be interrupted. See "Cleaning Your

Washer" in the "Washer Care" section.

IMPORTANT: Do not place garments or other items in the washer

during the Clean Washer With AFFRESH TM cycle. Use this cycle with

an empty wash drum.

Soak

Use the Soak cycle to help remove small spots of set-in stains on

fabrics. This cycle provides a soak time with warm or cold water

followed by drain. Extra water, a short tumbling phase for equal

distribution of the laundry, and asoaking time without drum

movement improve the removal of set-in stains. Drain without spin

assures gentle treatment, even for delicate articles.

Rinse/Spin

Use this cycle to get a rinse and spin only. This cycle combines fast-

speed tumbling and high speed spin. If desired, you can reduce the

spin speed by selecting the speed you want from the SPIN SPEED

modifier.

A Rinse/Spin cycle is useful for:

• Loads that need rinsing only, like swimsuits.

NOTE: For more delicate loads, when using a Rinse & Spin

cycle to rinse swimwear, change the Speed Spin Modifier

setting to Medium or Low to avoid fabric stress.

• Adding fabric softener to a load.

Drain/Spin

Use this cycle to drain your washer or to drain and spin your wash

load. The spin speed is preset to high. Ifdesired, you can reduce the

spin speed by selecting the speed you want from the SPIN SPEED

modifier.

NOTE: Loads of synthetics, delicate fabrics, hand washables, and

washable woolens should be drained with no spin or low spin speed

to avoid fabric stress.

As with any new product, you will hear sounds that you are not

accustomed to. You may hear various sounds when the door is

locked and unlocked, and during the washing, rinsing, and spinning

process. Between changes in wash actions, there will be

momentary pauses. You will hear water spraying and splashing

during the wash and rinse cycles. These new sounds and pauses

are part of normal washer operation.

You can customize your wash by adding options to your cycle

selections. You can add or change an option after starting a cycle

anytime before the selected option begins. Not all options are

available with all cycles. Available options will glow amber. Current

selections will glow green. If an option is unavailable with a selected

cycle, the light will not illuminate.

DelayWash

• DeepClean • NightQuiet

Soft

;rE_ Off

NightQuiet TM option

In this option, the washer will sense vibration in the wash cycle and

may adjust the spin speed to lower sound levels generated during

the spin.

Cycle Signal

This signal is helpful when you are removing items from the

washer as soon as it stops. Press CYCLE SIGNAL to select Loud,

Soft, or Off. To activate/deactivate button sound hold cycle signal

button for 3 seconds.

• Cycle

TumbleFresh Signal

Button Sound On/Off

Holdfor 3Sec

• See the "Laundry Guide" for an overview of possible options for

each Wash Cycle selection.

• You can select more than one option for a cycle. Some options

cannot be added to some cycles. For example, Deep Clean

cannot be added to the Quick Wash cycle.

• If an option is unavailable with aselected cycle, there will be

3 short tones, and the light for that option will not glow when

selected.

Delay Wash

To begin the wash cycle later, select DELAY WASH until the desired

delay time (in hours) shows in the Estimated Time Remaining

display, and then select START.The countdown to the wash cycle

will show in the display window, and the button indicator will blink

until the cycle begins.

IMPORTANT: When delaying a cycle, use only powdered

detergents in the high efficiency "HE" detergent compartment

since liquid detergents may seep out of the compartment during

Delay Wash, before the wash cycle begins.

TumbleFresh TM option

Use this option when you are not able to unload your clothes,

soon after the wash cycle ends. This option provides periodic

tumbling for up to 6 hours to help freshen your clothes. During

this time, the "Done" indicator remains activated, the door

remains locked, and the TumbleFresh TM indicator light will flash.

The TumbleFresh TM option will automatically stop and the door

lock will be released after this time expires, or if you press cancel

at anytime to unload your laundry.

Deep Clean with Steam

Use this option for heavily soiled loads that need improved stain

treatment, loads with multiple types of stains, or loads you

suspect as having stains, but are afraid may have been missed

(no sorting or searching for stains). When Deep Clean with Steam

is selected, the water temperature of the selected wash cycle is

automatically set to warm. The water will then be slowly heated to

the temperature selected, along with steam, to aid in stain removal.

This option will provide optimal removal of organic stains such as

blood and grass.

Preset cycle settings of Water Temperature, Spin Speed, Soil

Level, and Rinse can be changed. You can change a modifier after

starting a cycle anytime before the selected modifier begins. Not all

modifiers are available with all cycles and options. Available options

will glow amber. Current selections will glow green. If a modifier is

unavailable with aselected cycle, the light will not illuminate.

NOTE: The panel shown below may be different from that of your

model.

li sanitize [i High I!

Hot Medium • Heavy _OMax

Warm Low Normal Io Extra

Cold NoSpin Light LONormal

WaterTemp Spin S0il Rinse

All Cold Speed Level

Rinses

• To change the water temperature, select the WATER TEMP

button until the desired setting glows green.

• To change the spin speed, select the SPIN SPEED button

until the desired setting glows green.

• To change cycle time, select SOIL LEVEL button until the

desired setting glows green.

• To change the rinse, select RINSE button until the desired

setting glows green.

Water Temp

Select a water temperature based on the type of load you are

washing. Use the warmest wash water safe for fabrics. Follow

garment label instructions.

In wash water temperatures colder than 60°F (15.6°C), detergents

do not dissolve well. Soils may be difficult to remove.

• This washer has a Sanitize water temperature that is certified

by NSF International, an independent third-party testing and

certification organization. The certification verifies that the

sanitizing cycle reduces 99.9% of bacteria typically found

on clothing, bedding, and towels, and there is no carryover

of bacteria between loads after the cycle is complete.

Certified to Sanitize

• The Sanitize temperature provides an extra high temperature

to remove 99.9% of certain bacteria. It is recommended that

you set your hot water heater to 120°F (49°C) to ensure proper

performance during this cycle.

• The Sanitize Water Temp uses high water temperatures.

Please check garment care label to avoid garment damage.

• In wash water temperatures colder than 60°F (15.6°C),

detergents do not dissolve well. Soils may be difficult

to remove.

Only cycles with sanitize wash temperature selected have been

designed to meet the requirements of NSF Protocol P172 for

Sanitizing Efficacy.

6TH SENSE _ Technology

The 6TH SENSEC_Technology control electronically senses and

maintains a uniform water temperature. 6TH SENSE_ Technology

control regulates incoming hot and cold water. 6TH SENSE_

Technology control is automatically turned on when a cycle is

selected. See "Preset Cycle Settings" in "Cycles." 6TH SENSECe

Technology control ensures consistent cleaning.

6TH SENSE_Technology control works for allwash temperature

settings.

6TH SENSEe_Technology works for the rinse temperature where

the wash temperature setting is marked with an

asterisk, such as Warm*. All other rinse temperatures are

cold.

sense °

Rinse

Extra Rinse

An extra rinse can be used to aid the removal of detergent or bleach

residue from garments. This option provides an additional rinse with

the same water temperature as the normal rinse.

Max Rinse

This option provides the best rinse level to allow for even better

detergent removal.

Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these

washer cycles.

CYCLE SUGGESTED LOAD TYPE AVAILABLE OPTIONS

Delay Wash Deep Clean TumbleFresh TM NightQuiet TM

STEAM

Whitest Whites Soiled white fabrics ,/ ,/ ,/ ,/

Heavy Duty Sturdy, colorfast fabrics and heavily soiled garments ,/ ,/ ,/ ,/

Bulky Items Normally soiled blankets and comforters #" #" #" #"

Active Wear Use this cycle to wash small loads of exercise wear #" #" #"

or other high-performance clothing that require

gentle fabric care

Normal/Casual Normally soiled blouses, shirts, overalls, etc., made ,/ ,/ ,/ ,/

of polyester, nylon, cotton, linen, or cotton blends

Delicate Special-care items marked "Hand Washable" ,/ ,/ ,/

Hand Washables Special-care items marked "Hand Washable" ,/ ,/ ,/

Quick Wash 2-3 lightly soiled wear items made of cotton, #" #" #"

polyester, nylon, or cotton blends

Clean Washer No clothes, use AFFRESH_ewasher cleaner tablet

With AFFRESH TM or chlorine bleach

Soak Fabrics made of cotton, linen, polyester, or nylon ,/

Rinse/Spin Fabrics made of cotton, linen, polyester, or nylon ,/ ,/ ,/

Drain/Spin Fabrics made of cotton, linen, polyester, or nylon ,/ ,/ ,/

LAUNDRYTIPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of your

garments.

• Use only High Efficiency detergents. The package for this type

of detergent will be marked "HE" or "High Efficiency." This

wash system, along with less water, will create too much

sudsing with a regular non-HE detergent. Using regular

detergent will likely result in washer errors, longer cycle times,

and reduced rinsing performance. It may also result in

component failures and noticeable mold or mildew. HE

detergents are made to produce the right amount of suds for

the best performance. Follow the manufacturer's instructions

to determine the amount of detergent to use. Remember,

concentrated detergents such as 2x or higher will use less

detergent based on load size.

Sorting

• Separate heavily soiled items from lightly soiled ones, even if

they would normally be washed together. Separate lint-givers

(towels, chenille) from lint-takers (corduroy, synthetics,

permanent press). When possible, turn lint-givers inside out.

Separate dark colors from light colors, colorfast items from

noncolorfast items.

Sort by fabric and construction (sturdy cottons, knits, delicate

items).

Unloading

• Remove clothes from washer after the cycle is completed.

Metal objects such as zippers, snaps, and buckles may rust

if left in the washer basket for a long time.

• When unloading garments, occasionally check under the gray

colored seal at the front of the tub for small items.

Use only HE detergenL

Close zippers, snaps, and hooks to avoid snagging other items.

Remove pins, buckles, and other hard objects to avoid

scratching the washer interior. Remove non-washable trim

and ornaments.

Empty pockets and turn them inside out.

Turn down cuffs; brush away lint and dirt.

Turn wool and synthetic knits inside out to avoid pilling.

Tie strings and sashes so they will not tangle.

Mend tears, loose hems, and seams.

Treat spots and stains.

Stained or wet garments should be washed promptly for best

results.

Mix large and small items, avoid washing single items,

and load evenly.

Wash small items, such as infant socks, in amesh garment bag.

Tocreate a balanced load, it is recommended that more than

one garment bag be used, and that each garment bag be filled

with equal amounts of material.

NOTE: If you are washing only small items, it is recommended

that more than one mesh garment bag be used, and that each

garment bag be filled with equal amounts of material.

Loading suggestions

Heavy Work Clothes

4 jeans 2 sweatpants

4 workpants 2 sweatshirts

4 workshirts

Towels

10 bath towels 14 washcloths

10 hand towels

Mixed Load

3 sheets (1 king, 2 twin) 9 T-shirts

4 pillowcases 9 shorts

3 shirts 10 handkerchiefs

3 blouses

Quick Wash

(2-3 garments) 2 dress shirts

1 pair dress pants

WASHERCARE

The Washer Maintenance Procedure should be performed on a

monthly basis.

Cleaning the door seal

1. Open the washer door and remove any clothing or items from

the washer.

2. Inspect the gray colored seal between the door opening and

the basket for stained areas. Pull back the seal to inspect all

areas under the seal and to check for foreign objects.

A. Seal

3. If stained areas are found, wipe down these areas of the seal,

using the procedure that follows.

a} Mix a dilute solution, using s/4cup (177 mL) of liquid

chlorine bleach, and 1 gal. (3.8 L) of warm tap water.

b} Wipe the seal area with the dilute solution, using a damp

cloth.

c} Let stand 5 minutes.

d} Wipe down area thoroughly with a dry cloth and let the

washer interior air dry with door open.

IM PORTANI"."

• Wear rubber gloves when cleaning for prolonged periods.

• Refer to the bleach manufacturer's instructions for proper use.

Washer Maintenance Procedure

This washer has a special cycle that uses higher water volumes

and steam, in combination with AFFRESH Qwasher cleaner or

liquid chlorine bleach, to thoroughly clean the inside of the

washer.

NOTES:

• Read these instructions completely before beginning the

cleaning process.

• If necessary, the cleaning cycle may be interrupted by pressing

the Pause/Cancel button. However, this will not immediately

stop the cycle. The machine will display "int" (interrupt) and

continue with several rinse and drain steps to ensure that all

remaining bleach is rinsed from the washer.

If using liquid chlorine bleach:

Open the dispenser drawer and immediately add 2/scup

(160 mL) of liquid chlorine bleach to the bleach compartment.

NOTE: Do not add any detergent to this cycle. Use of more

than 2/scup (160 mL) of bleach will cause product damage

over time.

3. Close the washer door and dispenser drawer.

4. Select the CLEAN WASHER With AFFRESH Mcycle.

5. Press START.

NOTE: The basket will rotate, then the door will unlock, lock

again, and then the cycle will continue.

• The machine will bring in some inlet water, and the basket

will rotate while the washer runs a short sensing cycle. This

will take approximately 3 minutes.

6. The cycle will determine whether clothing or other items are in

the washer.

a} If no items are detected in the washer, it will proceed to

Step 7.

b} If any items are detected in the washer, "rL" (remove load)

will be displayed, and the WASH and CONTROL LOCK

lights will remain lit. The door will unlock. Open and

remove any garments in the wash drum.

• Press PAUSE/CANCEL to cancel the failure code. Then

repeat steps 3, 4, and 5 to start the cycle again.

7. Once the cycle has begun, allow the cycle to complete.

8. After the cycle is complete, leave the door open slightly, to

allow for better ventilation and drying of washer interior.

Always do the following to maintain washer freshness

• Use only HE High Efficiency detergent.

• Leave the door slightly open after each cycle to allow for better

ventilation and drying of washer interior.

• Repeat the cleaning procedure monthly, using one AFFRESH <e

tablet or 2/scup (160 mL) of liquid chlorine bleach.

• If the procedure does not sufficiently improve the machine

freshness, evaluate your installation and usage conditions for

other causes.

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to keep it looking

new. Use mild soap and water. Do not use abrasive products.

Cleaning the dispenser drawer

The dispenser drawer is removable for easy cleaning.

1. Unlock the dispenser drawer by pressing the Release Lever in

the Prewash compartment. See "Using the Dispenser."

Remove the drawer.

2. Remove the inserts (the siphon from the softener and bleach

compartments and the detergent selector).

3. Wash the parts under running water.

4. Replace the inserts and return the dispenser to the drawer.

Begin procedure

1. Open the washer door and remove any clothing or items from

the washer.

2. Using the AFFRESH _ washer cleaner (Recommended):

Add one AFFRESH <_washer cleaner tablet to the washer

drum.

Replace inlet hoses after 5 years of use to reduce the risk of hose

failure. Periodically inspect and replace inlet hoses if bulges, kinks,

cuts, wear, or leaks are found.

When replacing your inlet hoses, record the date of replacement.

_ _,_ _-_'_ _ _'/ _,_ _÷f_ _ _-_ _ _

Install and store your washer where it will not freeze. Because

some water may stay in the hoses, freezing can damage your

washer. Ifstoring or moving your washer during freezing weather,

winterize it.

Non-use or vacation care:

Operate your washer only when you are at home. If you will be on

vacation or not using your washer for an extended period of time,

you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer. This helps avoid

unintended flooding (due to a water pressure surge) while

you are away.

• Slightly open door to provide ventilation.

To winterize washer:

1. Put 1 qt (1 L)of R.V.-type antifreeze in the drum.

2. Run washer on a Drain/Spin cycle.

3. Unplug washer or disconnect power.

4. Shut off both water faucets.

5. Disconnect water inlet hoses from faucets and drain.

To use washer again:

1. Flush water pipes. Reconnect water inlet hoses to faucets.

Turn on both water faucets.

To transport the washer:

1. If washer will be moved during freezing weather, put in 1 qt

(1 L) of R.V.-type antifreeze in the drum. Run washer on a

Drain/Spin cycle.

2. Unplug the power cord.

3. Disconnect the drain hose from the drain system and attach

to rear panel clips.

4. Shut off both water faucets.

5. Disconnect the water inlet hoses from faucets, then drain the

hoses and clip them to the rear panel of the washer.

IMPORTANT: Call for service. Do not reuse transport bolts.

Washer must be transported in the upright position. To avoid

suspension and structural damage to your washer, it must be

properly set up for relocation by a certified technician.

Reinstalling the washer

1. Follow the "Installation Instructions" to locate, level,and connect

the washer.

2. Run the washer through the Quick Wash cycle with W the

manufacturer's recommended amount of HE detergent for a

medium-size load, to clean the washer and remove the antifreeze,

if used.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Falure to follow these instructions can result in death,

fire, or electrical shock.

Plug in washer or reconnect power.

Run the washer through the Quick Wash cycle with _/2the

manufacturer's recommended amount of HE detergent for a

medium-size load, to clean the washer and remove the

antifreeze, if used.

La page charge ...

Whirlpool WFW9550WW01 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WFW9550WW01

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WFW9550WW01 Owner's manual

Whirlpool WFW9550WW01 Le manuel du propriétaire

Ce manuel convient également à

Whirlpool WFW9550WW01 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents