LG TWC101KLMK6 Le manuel du propriétaire

ROOM AIR CONDITIONER

OWNER'S MANUAL

MANUEL D'UTILISATION

CLIMATISEUR DE FENÊTRE

website http://www.LG.ca

Please read the operating instructions and safety precautions

carefully and thoroughly before installing and operating your

room air conditioner.

Veuillez lire attentivement et en entier ce guide d’utilisation et

le

s mesures de sécurité ci-incluses avant de procéder à

l’installation et au fonctionnement de votre climatiseur.

MODEL, MODÉLE

WL Series:

2 Room Air Conditioner

Window-Type Air Conditioner Owner’s Manual

TABLE OF CONTENTS

FOR YOUR RECORDS

Write the model and serial numbers here:

Model #

Serial #

You can find them on a label on the side of each unit.

Dealer's Name

Date Purchased

■ Staple your receipt to this page in the event you need

it to prove date of purchase or for warranty issues.

READ THIS MANUAL

Inside you will find many helpful hints on how to use

and maintain your air conditioner properly. Just a little

preventive care on your part can save you a great deal

of time and money over the life of your air conditioner.

You'll find many answers to common problems in the

chart of troubleshooting tips. If you review our chart of

Troubleshooting Tips first, you may not need to call

for service at all.

PRECAUTION

• Contact the authorized service technician for repair or

maintenance of this unit.

• Contact the installer for installation of this unit.

• The air conditioner is not intended for use by young

children or invalids without supervision.

• Young children should be supervised to ensure that

they do not play with the air conditioner.

• When the power cord is to be replaced, replacement

work shall be performed by authorized personnel only

using only genuine replacement parts.

• Installation work must be performed in accordance with

the National Electric Code by qualified and authorized

personnel only.

Safety Precautions.....................3

Operating Instructions ..............8

Care and Maintenance.............11

Hardware Installation ..............13

Common Issues.......................27

Owner's Manual 3

Safety Precautions

ENGLISH

To prevent injury to the user or other people and property damage, the following instructions must

be followed.

■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is

classified by the following indications.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

■ Meanings of symbols used in this manual are as shown below.

Be sure not to do.

Be sure to follow the instruction.

WARNING

■ Installation

Always install the expansion panel(s).

• No installation may cause fire and electric

shock accident.

Do not place the power cord near a heater.

• It may cause fire and electric shock.

Do not use the power cord near flammable

gas or combustibles such as gasoline,

benzene, thinner, etc.

• It may cause explosion or fire.

Do not disassemble or modify products.

• It may cause failure and electric shock.

Gasolin

Safety Precautions

4 Room Air Conditioner

Safety Precautions

■ Operation

Plug in the power plug

properly.

• Otherwise, it will cause

electric shock or fire due to

heat generation or electric

shock.

Do not operate or stop the

unit by inserting or pulling

out the power plug.

• It will cause electric shock or

fire due to heat generation.

Do not damage or use an

unspecified power cord.

• It will cause electric shock or

fire.

Do not modify power cord

length.

• It will cause electric shock or

fire due to heat generation.

Do not share the outlet with

other appliances.

• It will cause electric shock or

fire due to heat generation.

Always plug into a

grounded outlet.

• No grounding may cause

electric shock (See

Installation Manual).

Unplug the unit if strange

sounds, odors, or smoke

come from it.

• Otherwise it may cause fire

and electric shock accident.

Do not use the socket if it is

loose or damaged.

• It may cause fire and electric

shock.

Do not operate with wet

hands or in damp

environment.

• It will cause electric shock.

ON

Owner's Manual 5

Safety Precautions

ENGLISH

Do not allow water to run

into electric parts.

• It will cause failure of machine

or electric shock.

Leave the door closed while

the air conditioner is

running.

• It is not designed to cool the

entire house.

Ventilate before operating

air conditioner when gas

goes out.

• It may cause explosion, fire,

and burn.

Never touch the metal parts

of the unit when removing

the filter.

• They are sharp and may

cause injury.

Do not block the inlet or

outlet.

• It may cause failure of

appliance or accident.

Ensure that the outer case

is not damaged by age or

wear.

• If leaving appliance damaged,

there is concern of damage

due to the falling of product.

Be cautious not to touch the

sharp edges when

installing.

• It may cause injury.

Hold the plug by the head

when taking it out.

• It may cause electric shock

and damage.

Turn off the main power

switch when not using it for

a long time.

• Prevent accidental startup

and the possibility of injury.

CAUTION

■ Installation

Sharp

edges

■ Operation

6 Room Air Conditioner

Safety Precautions

Do not place heavy object

on the power cord and take

care so that the cord should

not be pressed.

• There is danger of fire or

electric shock.

If water enters the product,

turn off the the power switch

of the main body of appliance.

Contact service center after

taking the power-plug out

from the socket.

Do not clean the air

conditioner with water.

• Water may enter the unit and

degrade the insulation. It may

cause an electric shock.

Turn off the power and

breaker firstly when

cleansing the unit.

• Since the fan rotates at high

speed during operation, it

may cause injury.

Do not put a pet or house

plant where it will be

exposed to direct air flow.

• This could injure the pet or

plant.

Do not use this appliance

for special purposes such

as pets, foods, precision

machinery, or objects of art.

• It is an air conditioner, not a

precision refrigeration system.

Always insert the filter

securely.

Clean it every two weeks.

• Operation without filters will

cause failure.

Use a soft cloth to clean. Do

not use wax, thinner, or a

strong detergent.

• The appearance of the air

conditioner may deteriorate,

change color, or develop

surface flaws.

Do not drink water drained

from air conditioner. / Do

not direct airflow at room

occupants only.

• It contains containments and

will make you sick. / This

could damage your health.

Wax

Thinner

Owner's Manual 7

Safety Precautions

ENGLISH

Preparing for operation

Contact an installation specialist for installation.

Plug in the power plug properly.

Do not share the same outlet with other appliances

Do not use an extension cord.

Do not start/stop operation by plugging/unplugging the power cord.

If cord/plug is damaged, replace only with an authorized part.

6

5

4

3

2

1

Usage

Cleaning and maintenance

Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp

metal edges.

Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading

to possible electric shock.

When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a

very high speed during operation. There is a possibility of injury if the unit’s power is accidentally

triggered on while cleaning inner parts of the unit.

3

2

1

Service

For repair and maintenance, contact your authorized service dealer.

Being exposed to direct airflow for an extended period of time could be hazardous to your health. Do not

expose occupants, pets, or plants to direct airflow for extended periods of time.

Due to the possibility of oxygen deficiency, ventilate the room when using together with stoves or other

heating devices.

Do not use this air conditioner for non-specified special purposes (e.g. preserving precision devices,

food, pets, plants, and art objects). Usage in such a manner could harm such property.

3

2

1

Prior to Operation

OPERATIONTHERMOSTAT

OFF

HIGH

COOL

MED

COOL

LOW COOL

MED

FAN

LOW

FAN

8 Room Air Conditioner

Operating Instructions

Location and Function of Controls

The controls will look like following picture.

■ OPERATION

High Cool, Med Cool and Low Cool provide cooling with different fan speeds. Med Fan or Low

Fan provides air circulation and filtering without cooling. Off turns the air conditioner off.

: If you move the switch from a cool setting to off or to a fan setting, wait at least 3 minutes

before switching back to a cool setting.

Cooling Descriptions

For Normal Cooling- Select High Cool or Med Cool with the Operation knob at the midpoint of

Thermostat knob.

For Maximum Cooling- Select High Cool with the Operation knob at the highest number

available on your Thermostat knob.

For Quieter & Nighttime Cooling- Select Low Cool with the Operation knob at the midpoint of

Thermostat knob.

■ THERMOSTAT

The THERMOSTAT is used to maintain the room temperature. The compressor will cycle on

and off to keep the room at the same level of comfort. When you turn the knob to a higher

number(the right side) and the indoor air will become cooler.

The 5 or 6 position (the middle position of arc) is a normal setting for average conditions.

CAUTION

: When the air conditioner has been performed its cooling operation and is turned off or set to

the fan position, wait at least 3 minutes before resetting to the cooling operation again.

NOTICE

Function of Controls

Owner's Manual 9

Operating Instructions

ENGLISH

Power

Te mp

Fan Speed

Timer Mode

˚C

TIMER POWERMODE

TEMP

FAN

SPEED

F1 LOW

F2 MED

F3 HIGH

Dry Timer

Fan

Energy

Saver

Cool

1

2

6

3 45

1

2

3

4

5

Push out the cover on the back of the remote control with your thumb

Pay attention to polarity and insert two new AAA 1.5V batteries.

Reattach the cover.

:

Do not use rechargeable batteries. Make sure that both batteries are new.

• In order to prevent discharge, remove the batteries from the remote control if the air

conditioner is not going to be used for an extended period of time

Keep the remote control away from extremely hot or humid places.

To maintain optimal operation of the remote control, the remote sensor should not be

exposed to direct sunlight.

• The remote control can be mounted on a wall using the mountable holder.

NOTICE

3

2

1

Inserting the Remote Control Batteries

POWER

Operation starts when this button is pressed and

stops when you press the button again.

TEMPERATURE CONTROL

The thermostat monitors room temperature to

maintain the desired temperature.

The thermostat can be set between 16°C~30°C.

The unit takes an average of 30 minutes to adjust

the room temperature by 1°C.

OPERATION MODE SELECTOR

Select cooling mode to cool the room.

Select energy saver mode for energy saving

operation.

Select fan mode for basic ventilating fan

operation.

Select dry mode for dry operation.

FAN SPEED SELECTOR

For increased power while cooling, select a

higher fan speed.

3 steps: High ➔ Low ➔ Med

ON/OFF TIMER

The timer can be set to start and stop the unit in

hourly increments (up to 12 hours).

REMOTE CONTROL SENSOR

6

5

4

3

2

1

Remote Control OperationsRemote Control Operations

AUTO RESTART

In failure of electric power, the unit runs as previous setting operation.

The remote control and control panel will look like those represented in the following pictures.

10 Room Air Conditioner

Operating Instructions

VENTCLOSE

OPEN

Part

A

Vent Control

For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation.

OPENtheventtodischargestaleair.

Adjusting the Air Flow Direction

• Recommended orientation of louvers

Adjust louvers to face upwards when cooling to maximize cooling efficiency.

Airflow can be adjusted by changing the direction of the air conditioner's louvers. This can also increase the

cooling efficiency of the air conditioner.

: Before using the ventilation feature, position the vent lever by

pulling Part A out straight and snapping it into place.

NOTICE

Adjusting horizontal air flow Adjusting vertical air flow

• Adjusting Horizontal Air Flow Direction

Adjusting the vertical louvers left and right will

change horizontal airflow.

• Adjusting Vertical Air Flow Direction

Adjusting the horizontal vane up and down will

change vertical airflow. The vane can be adjusted

by nudging the vane backward or forward.

Adjusting the Air Flow Direction

Owner's Manual 11

Care and Maintenance

ENGLISH

Drain pipe

Drain cap

Turn the power off and unplug the power plug before cleaning the air conditioner.

Air Filter

The air filter behind the inlet grille should be checked and cleaned at least once every 2 weeks (or as

necessary) to maintain optimal performance of the air conditioner.

How to remove the air filter

The grille may be opened from the top for easy

maintenance after installation.

Open the inlet grille by pulling off the exposed door

on the top of the unit (based on installation).

Pull the tab slightly to release the filter. Pull the filter

in the same direction as the opening.

Clean the filter with warm, soapy water. The water

should be below 40°C (104°F).

Rinse off and gently shake off excess water from the

filter. Let it dry before replaceing it.

5

4

3

2

1

Drainage

The base pan may overflow due to high humidity. To drain the excess

water, remove the drain cap from the back of the unit and secure the

drainpipe.

When pressing the drainpipe into place, apply force in the direction

away from the fins to avoid injuring yourself.

Care and Maintenance

12 Room Air Conditioner

Care and Maintenance

CABINET

DRAIN

PAN

DRAIN HOSE

SCREW

Take the drain pan which is located in the air

discharge.

Remove the hole rubber from the base-pan (for

some models).

Install the drain pan to the right corner of the

cabinet with 4 (or 2) screws.

Connect the drain hose of 3/5" inside diameter to

the outlet located at the bottom of the drain

pan.You can purchase the drain hose or tubing

locally to satisfy your particular needs. (Drain

hose is not supplied).

4

3

2

1

How to Attach Drain Pan (Optional)

The air conditioner employs a proper drain method whereby the condensed water (moisture removed from the

air) is drained to the outside.

In very humid weather, (and for reverse cycle models in the reverse mode) excessive condensate water removed

from the air may cause some water to collect. To remove this excess water you can install the drain pan as

detailed below.

Owner's Manual 13

Hardware Installation

ENGLISH

B

A

Power cord

4

6

5

8

1

2

3

13

15

11

14

12

10

9

7

Product Features

1. CABINET

2. FRONT GRILLE

3. AIR FILTER

4. AIR INTAKE (INLET GRILLE)

5. AIR DISCHARGE

6. VERTICAL AIR DEFLECTOR

(HORIZONTAL LOUVER)

7. EVAPORATOR

8. HORIZONTAL AIR DEFLECTOR

(VERTICAL LOUVER)

9. CONTROL PANEL

10. POWER CORD

11. COMPRESSOR

12. BASE PAN

13. BRACE

14. CONDENSER

15. REMOTE CONTROLLER(OPTIONAL)

Remote Control Operations

Installing the Power cord

You can choose between two methods below according to your window stool shape and preference.

• Fasten the stopper using 2 screw holes, and lead

out the power cord through slit "A".

• Fasten the stopper using left screw hole, and rotate

properly to lead the power cord out through slit "B".

Using slit "A" Using slit "B"

CAUTION

: This appliance should be installed in accordance with national wiring regulations. The

following information serves acts as a guide to help to explain product features.

Hardware Installation

14 Room Air Conditioner

Hardware Installation

About

1

/2"

30"~60"

Awning

Cooled air

Fence

Over 20"

Heat

radiation

23" to 36"

Offset

1

/2" to 1

1

/4"

Sill

Exterior

Interior wall

20

1

/12" min.

(Without frame curtain)

Stool

15" min

(With frame curtain)

How to Install the Unit

To prevent vibration and noise, make sure the unit

is installed securely and firmly.

Install the unit where the sunlight does not shine

directly on the unit.

The outside of the cabinet must extend outward for

at least 12" and there should be no obstacles, such

as a fence or wall, within 20" from the back of the

cabinet because it will prevent heat radiation of the

condenser.

Restriction of outside air will greatly reduce the

cooling efficiency of the air conditioner.

CAUTION

: All side louvers of the cabinet must remain exposed to the outside of the structure.

Install the unit a little slanted so the back is slightly lower than the front (about 1/2").

This will force condensed water to flow to the outside.

Install the unit with the bottom about 30"~60" above the floor level.

5

4

3

2

1

Window Requirements

: All supporting parts should be secured to firm wood,

masonry, or metal.

• This unit is designed for installation in standard double

hung windows with actual opening widths from 23"

to 36".

• The top and bottom window sash must open sufficiently

to allow a clear vertical opening of 15" from the bottom

of the upper sash to the window stool.

NOTICE

WK Series

Owner's Manual 15

Hardware Installation

ENGLISH

About

1

/2"

30"~60"

Awning

Cooled air

Fence

Over 20"

Heat

radiation

27" to 39"

Offset

1

/2" to 1

1

/4"

Sill

Exterior

Interior wall

23

5

/8" min.

(Without frame curtain)

Stool

16" min

(With frame curtain)

How to Install the Unit

To prevent vibration and noise, make sure the unit

is installed securely and firmly.

Install the unit where the sunlight does not shine

directly on the unit.

The outside of the cabinet must extend outward for

at least 12" and there should be no obstacles, such

as a fence or wall, within 20" from the back of the

cabinet because it will prevent heat radiation of the

condenser.

Restriction of outside air will greatly reduce the

cooling efficiency of the air conditioner.

CAUTION

: All side louvers of the cabinet must remain exposed to the outside of the structure.

Install the unit a little slanted so the back is slightly lower than the front (about 1/2").

This will force condensed water to flow to the outside.

Install the unit with the bottom about 30"~60" above the floor level.

5

4

3

2

1

Window Requirements

: All supporting parts should be secured to firm wood,

masonry, or metal.

• This unit is designed for installation in standard double

hung windows with actual opening widths from 27"

to 39".

• The top and bottom window sash must open sufficiently

to allow a clear vertical opening of 16" from the bottom

of the upper sash to the window stool.

NOTICE

WL Series

16 Room Air Conditioner

Hardware Installation

About

1

/2"

30"~60"

Awning

Cooled air

Fence

Over 20"

Heat

radiation

29" to 41"

18" min.

Inner sill

Offset

Window

Sash

Sill

Exterior

Interior wall

29" min.

(Without frame curtain)

How to Install the Unit

To prevent vibration and noise, make sure the unit

is installed securely and firmly.

Install the unit where the sunlight does not shine

directly on the unit.

There should be no obstacles, such as a fence and

wall, within 20" from the back of the cabinet

because it will prevent heat radiation of the

condenser.

Restriction of outside air will greatly reduce the

cooling efficiency of the air conditioner.

CAUTION

: All side louvers of the cabinet must remain exposed to the outside of the structure.

Install the unit a little slanted so the back is slightly lower than the front (about 1/2").

This will force condensed water to flow to the outside.

Install the unit with the bottom about 30"~60" above the floor level.

5

4

3

2

1

Window Requirements

: All supporting parts should be secured to firm wood, masonry, or metal.

• This unit is designed for installation in standard double

hung windows with actual opening widths from 29"

to 41".

• The top and bottom window sash must open sufficiently

to allow a clear vertical opening of 18" from the bottom

of the upper sash to the window stool.

NOTICE

WP Series

Owner's Manual 17

Hardware Installation

ENGLISH

1

2 3 4

8 13

10

765

12

119

10

13

Shipping

Screws

(Type A)

5

11

5

Upper guide

Installation Kits Contents

Suggested Tool Requirements

NO. NAME OF PARTS Q'TY

1 FRAME CURTAIN 2

2 SILL SUPPORT 2

3BOLT 2

4NUT 2

5 SCREW (TYPE A) 16

6 SCREW (TYPE B) 3

7 SCREW (TYPE C) 5

8FOAM-STRIP 1

9DRAINPIPE 1

10 FOAM-PE 1

11 FRAME GUIDE 2

12 WINDOW LOCKING BRACKET 1

13 FOAM-PE 1

PREPARATION OF CHASSIS

Remove the screws which fasten the cabinet at both

sides and at the back.

Slide the unit from the cabinet by gripping the base pan

handle and pulling forward while bracing the cabinet.

Cut the window sash seal to the proper length.

Peel off the backing and attach the Foam-PE

to the

underside of the window sash.

Remove the backing from the top upper guide Foam-PE

and attach it to the bottom of the Upper Guide.

Attach the upper guide onto the top of the cabinet with 3

Type A screws

.

Insert the Frame Guides into the bottom of the

cabinet.

Insert the Frame Curtain

into the Upper Guide and

Frame Guides .

Fasten the curtains to the unit with 4 Type

A screws .

8

7

6

5

4

3

2

1

SCREWDRIVER(Philips and Flatead), RULER, KNIFE, HAMMER, PENCIL, LEVEL

WK, WL Series

18 Room Air Conditioner

Hardware Installation

Cabinet Installation

Open the window. Mark a line on center of the

window stool.

Carefully place the cabinet on the window stool and

align the center mark on the bottom front with the

center line marked in the window stool.

Pull the bottom window sash down behind the Upper

Guide until it meets.

: Do not pull the window sash down tightly that the

movement of Frame Curtain

is restricted.

Loosely assemble the Sill Support using the parts

in Fig. 3.

Select the position that will place the Sill Support

near the outer most point on sill (See Fig. 4)

: Be careful when you install the cabinet

(Frame Guides are broken easily).

Attach the Sill Support to the cabinet track hole in

relation to the selected position using 2 Type A

screws in each support (See Fig. 4).

5

NOTICE

4

3

NOTICE

2

1

INDOOR OUTDOOR

Sill Support

2

Nut

4

Bolt

3

INDOOR OUTDOOR

Cabinet

About

1

/2"

Frame Guide

11

Screw(Type A)

5

Upper Guide

Window stool

Front Angle

Window Sash Upper guide

Frame Curtain

1

Foam-pe

10

Foam-pe

13

Cabinet

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Owner's Manual 19

Hardware Installation

ENGLISH

Sash track

Front Angle

About

1

/2"

Screw(Type B)

6

Screw(Type B)

6

Sill Support

2

Sill Support

2

Foam-Strip

8

Fig. 5

Type C

7

Fig. 6

Screw(Type A)

Screw

(Type A)

Power cord

Fig. 7

Fig. 8

The cabinet should be installed with a very slight tilt

(about 1/2") downward toward the outside

(See Fig. 5).

Adjust the bolt and the nut of Sill Support for

balancing the cabinet.

Attach the cabinet to the window stool by driving

the screws

(Type B: Length 16mm (5/8 inch)

and below.) through the front angle into window

stool.

Pull each Frame Curtain

fully to each window

sash track, and repeat step 2.

Attach each Frame Curtain the window sash using

screws (Type C). (See Fig. 6)

CAUTION

:

Donotdrillaholeinthebottompan.

The unit is designed to operate with

approximately 1/2" of water in bottom pan.

There is no need to add water if the

panisdry.

Slide the unit into the cabinet. (See Fig. 7)

CAUTION

:

For security purpose, reinstall screws

(Type A) at cabinet's sides.

Cut the Foam-Strip to the proper length and insert

between the upper window sash and the lower

window sash. (See Fig. 8)

11

10

9

8

7

6

20 Room Air Conditioner

Hardware Installation

Attach the Window Locking Bracket withaType

C screw .(SeeFig.9)

Attach the front grille to the cabinet by inserting the

tabsonthegrilleintothetabsonthefrontofthe

cabinet. Push the grille in until it snaps into place.

(See Fig. 10)

Pull down the inlet grille and secure it with a Type

A screw

through the front grille. (See Fig. 11)

Window installation of room air conditioner is

now completed. See ELECTRICAL DATA for

attaching power cord to electrical outlet.

15

14

13

12

Window locking

bracket

12

Fig. 9

Fig. 10

Fig. 11

La page charge ...

LG TWC101KLMK6 Le manuel du propriétaire

Ce manuel convient également à

LG TWC101KLMK6 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents