WiFi Adapter Manual
1. Introduction
WiFi Adapter is a device for SENA WIFI2.4G that charges and provides auto firmware upgrade.
WiFi Adapter can automatically connect to the router through the mobile app, automatically
download the latest firmware available for SENA Device, and can always upgrade to the latest
firmware through comparing firmware version when the user plugs SENA Device into the USB
port to charge.
2. WiFi Adapter features
●Supports WiFi related IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
●Smartphone App for iPhone and Android
●Firmware upgradeable
3. Contents
- Wifi Adapter
4. Product description
5. Getting started
a. Power On:
Insert the USB port into the charger and insert the Micro USB Port into the “USB power
port”
b. Connecting to WiFi
1. Open the mobile app
2. Connect to WiFi Docking
3. Setting WiFi Docking Station configuration
4. Select the WiFi router to connect to.
5. Enter the password of the selected WiFi router and click “Connect”
6. WiFi Adapter is connecting to the router.
7. Click “Setup Complete” when connected
8. After following these steps, WiFi Adapter should be connected to WiFi. “WiFi status” LED will
show blue light if the WiFi router is connected successful and show red light if there has
been a failure to connect.
9. To change the router connection, repeat the steps above.
10. You can update Sena devices such as 30K manually and update WiFi Docking Station
c. Charging SENA Bluetooth device
Plug in the Micro USB to sena Bluetooth device to charge the device. The “Charging status
LED” will show red light while charging and turn blue when the device is fully charged.
d. Upgrading Firmware
Firmware will be upgraded automatically while charging 30K through checking the firmware
version and downloading the latest firmware available.
“Firmware upgrade status” LED will show blue light when upgrade finished and blink while
firmware is upgrading.
FCC Warning
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed
and operated with minimum distance between 20cm the radiator your body: Use only the
supplied antenna.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Pour maintenir la conformité avec les lignes directrices de l’exposition RF de FCC, cet
équipement devrait être installé et exploité à une distance minimale de 20 cm le
radiateur de votre corps : utilisez seulement l’antenne fournie.
Manufacturer's Name: SENA TECHNOLOGIES.Inc
Product Name: WiFi Adapter
Trade Mark: SENA
Model number: SP126
Operating Temperature: -10°C to 40° C
This device is in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. All essential radio test suites have been carried out.
Detailed DOC file see attachment
The device complies with RF specifications when the device used at 20cm from your
body.
. The product shall only be connected to a USB interface of version USB2.0
Care for the environment! Must not be discarded with household waste!
RF Secification:
Function
Operation Frequency
Max RF
outputpower:
Limit
WIFI 802.11b/g/n(HT20)
802.11b/g/n(20MHz): 2412~2472MHz;
802.11b: 17.08dBm;
802.11g: 17.21dBm;
802.11n20: 16.49dBm;
20 dBm.
This product can be used across EU member states.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
dans d''autres langues
- English: Sena SP126 User manual
Autres documents
-
Comtrend Corporation WAP-5903 Manuel utilisateur
-
Extron WAP 100AC Manuel utilisateur
-
-
Netgear MBR1516 Manuel utilisateur
-
-
King WiFiMax KWM1000 Installation And Operating Instructions Manual
-
Alcatel-Lucent OA5710V Guide d'installation
-
Cradlepoint MBR1400 Series Manuel utilisateur
-
-
TP-LINK TGR1900 Manuel utilisateur