Lorex W452AS Series Mode d'emploi

Marque: Lorex

Modèle: W452AS Series

Taper: Mode d'emploi

V261LC_QSG_EN_R1

HD Video Floodlight

To prepare for installation:

Before assembly, there are important preparations to make.

• TURN OFF POWER TO YOUR

FLOODLIGHT CIRCUIT AT THE

FUSEBOX TO ENSURE NO

POWER IS BEING SENT. If you

are unsure of which breaker

controls the circuit, then turn

off the main power switch.

If you do not know where

your breaker is or how to turn

off power, consult a licensed

electrician.

• Verify that the supply voltage

is correct. Connect xture to a

100 VAC~240 VAC 50/60 Hz

power source.

• DO NOT connect oodlight to a

dimmer switch or timer.

• If you are not replacing a light

xture, you will need to run

power cabling to the install

location, and purchase a

UL listed junction box for a

licensed electrician to install.

LED Indicator

Quick Start Guide

Series

lorex.com

2k Outdoor Floodlight Camera

Package Contents

STEP 1: Preparation

Need Help?

Visit us online for up-to-date software

and complete instruction manuals

Click on the Downloads tab

Visit lorex.com

Search for the model

number of your product

Click on your product

in the search results

As our products are subject to continuous improvement, Lorex reserves the right to

modify product design, specications and prices, without notice and without incurring

Mounting Screws &

Anchors (×3)

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use and handling of the product.

• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh,

chemical-based cleaners.

• Use the product within given temperature, humidity and voltage levels noted in the

product’s specications.

• Do not disassemble the oodlight.

Safety Precautions

• Always follow code standards when installing wired connections.

• This oodlight camera must be installed on a wall and a UL listed junction box.

• This oodlight includes an Auto Mechanical IR Cut Filter. When the camera

changes between Day/Night viewing modes, an audible clicking noise may be

heard from the oodlight. This clicking is normal, and indicates that the camera

lter is working.

• Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation

assumes no liability for use of its products that does not conform with local laws.

Disclaimers

CAUTION

Risk of re.

Do not install camera near ammable or combustible surfaces.

Risk of electrical shock.

Disconnect the power at the fuse box before installation.

Hooks

Mounting Bracket

Scan for

Lorex Home APP

11.4”

290mm

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE

FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT

MAY CAUSE UNDESIRED OPERATION.

FCC Notice

Product Overview

PIR motion sensor

Speaker

Microphone

Camera

IR LED

Top cover

Light sensor

Memory slot*

Reset button**

Floodlights

Adjusting knobs

Wire Caps (×3)

Bracket Screws

A and B (×2)

Phillips Machine Screw

32 Feet

12.8” / 325mm

7.3” / 185mm

Mount the oodlight camera 10 feet (3 meters) high with the

motion detector levelled to the ground for optimizal detection

of human-sized objects as far as 32 feet (10 meters).

Recommendation:

Front Panel

Back Panel

Behavior Meaning

(steady) Operating correctly.

(ashing) Ready for connection.

(ashing rapidly) Mobile device is attempting to connect to the camera.

(steady) Device malfunction. Try resetting the camera and repeating the setup.

(ashing) Network connection failed. Try resetting the camera and repeating the setup.

(ashing rapidly) Memory slot error. Try removing and re-inserting the included memory slot card,

or try a different card.

(alternating) Firmware upgrade in progress. * To access the memory slot and reset button, twist left to open the top cover.

** To reset the camera, hold down the reset button until the chime sounds and the LED Indicator turns red.

V261LC_QSG_EN_R1.indd 1V261LC_QSG_EN_R1.indd 1 2020-03-03 5:40:22 PM2020-03-03 5:40:22 PM

W452AS

The user manual for local area network devices shall contain instructions

related to the restrictions mentioned in the above sections, namely that:

(i) the maximum antenna gain permitted for devices in the bands 5250-

5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(ii) the maximum antenna gain permitted for devices in the band 5725-

5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point

and non point-to-point operation as appropriate.

(i)ÿle gain d'antenne maximal autorisé pour les appareils dans les

bandes 5250-5350 MHz et 5470-5725 MHz doivent respecter le pire

limiter; et

(ii)ÿle gain d'antenne maximal autorisé pour les appareils dans la

bande 5725-5825 MHz doivent respecter le pire limites spécifiées pour

le point-à-point et l'exploitation non point à point, le cas échéant.

Users should also be advised that high-power radars are allocated as

primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650

-5850 MHz and that these radars could cause interference and/or

damage to LE-LAN devices.

Les utilisateurs de radars de haute puissance sont désignés utilisateurs

principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz

et 5650-5850 MHz et que ces radars pourraient causer du brouillage

et/ou des dommages aux dispositifs LAN-EL.

V261LC_QSG_EN_R1

Next, install the oodlight’s mounting bracket. Next, install the oodlight camera.

STEP 2: Secure the Mounting Bracket STEP 4: Secure the Floodlight

Hang the oodlight camera from the

mounting bracket using

the supplied hooks.

The copper wire from the camera is ground wire.

Connect the ground wire to the existing ground

wire inside of your junction box.

Use the supplied wire cap.

In the case that you are not wiring from a junction

box, twist your ground wire around the green

screw on the bracket.

The white wire from the camera is neutral

wire. Use a wire cap to connect the neutral

wires from the camera and junction box.

The black wire from your camera is a hot

wire. Use a wire cap to connect the hot

wires from the camera and junction box.*

1. With the power shut off, remove the existing light xture and

bracket from the wall.

2. Disconnect the wires.

1. Carefully push all the wires through the middle opening of the bracket

into the junction box, and secure the oodlight camera through the

middle hole using the Phillips machine screw.

In the case that you are installing the oodlight camera directly to the

bracket, t the wires into the back openings of the camera.

Hook one end into your oodlight camera.

Hook the other end into the bracket.

Overview of Lorex Home app

STEP 3: Connect the Wires

Back to

screen

Device

settings

Device name

Lorex Floodlight

Pause / Play FullscreenViewing

modes

Mute /

Unmute

Streaming

quality*

Play back

recorded

video

Snapshot

Siren

Manual

recording

Light

2-way audio: tap to speak, tap again to disable

* Change the streaming quality to SD (Standard Denition) to conserve bandwidth while

watching live video. This will not impact the quality of recorded video.

Live viewing screen:

To wire the oodlight:

To install directly to a junction box:

To install directly on a wall:

* Power wire colors in your home may be

different. In such a case consult a licensed

electrician.

IMPORTANT: Properly ground xture.

Floodlight Password:

1. Once the status LED on the oodlight is ashing green, tap Next in

the Lorex Home app. The app will connect your mobile device to the

oodlight’s hotspot.

2. Create a secure password for the oodlight. Record your oodlight

password below and store in a secure location:

3. Select your Wi-Fi

network from the list,

then enter the Wi-Fi

password to connect

your oodlight to the

Internet.

To link the oodlight:

4. Once the status LED on the oodlight is solid green, tap Next to add

the oodlight to your Lorex Home account.

5. Set a name for the oodlight and congure date & time preferences,

then tap Complete.

NOTE: Be sure to follow the “Front” / ”Up” directions on the mounting bracket.

3. Run the wires through the

middle of the supplied

mounting bracket.

4. Secure the mounting

bracket to your junction

box using one of the

bracket screws, A or B

depending on which

size ts.

STEP 5: In-app Setup

Next, connect the oodlight camera to the Lorex Home app.

NOTE: If the Wi-Fi

connection is weak,

try moving your router

closer or adding a Wi-Fi

extender.

1. Download and install the free Lorex Home app from

the App Store or Google Play Store.

2. Tap the Lorex Home icon to launch the app. Tap Sign

up, then follow the on screen prompts to create an

account. Record your account details below and

store in a secure location:

Email:

Account Password:

3. Wait for the oodlight to start up. This may take up to 5 minutes after

reconnecting power at the breaker.

To scan the QR code:

4. Once the status LED on

the oodlight is ashing

green, tap + in the Lorex

Home app.

5. Scan the QR code on the

side of the oodlight

camera using your

mobile device’s camera.

NOTE: If your mobile

device cannot scan the

QR code, tap Manually

enter Device ID.

2. Adjust the lens and light angle using the adjusting knobs.

3. To enforce a water resistant seal, apply silicone compound around the

entire perimeter where the junction box is attached to the bracket.

4. You may now restore power at the fusebox.

NOTE: If the status LED on the oodlight camera does not turn on, check

to make sure wiring is done correctly.

3. Use the mounting bracket

as a template to mark 3

holes in a triangular pattern.

4. Use a 1/4” drill bit to drill in

the marked holes.

5. Gently tap the supplied

mounting anchors into

the drilled holes with a

hammer.

6. Align the bracket and use

a Phillips head screwdriver

to secure the supplied

mounting screws into the

mounted anchors.

V261LC_QSG_EN_R1.indd 2V261LC_QSG_EN_R1.indd 2 2020-03-03 5:40:28 PM2020-03-03 5:40:28 PM

Please take attention that changes or modification not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation

of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts

de licence. L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.

This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm between

the radiator & your body.

ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 énoncée

dans un autre environnement.cette eqipment devrait être installé et exploité avec distance minimale de

20 entre le radiateur et votre corps.

Lorex W452AS Series Mode d'emploi

Marque: Lorex

Modèle: W452AS Series

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Lorex W452AS Series User guide

Lorex W452AS Series Mode d'emploi

Lorex W452AS Series Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents